Professional Documents
Culture Documents
Operating data
Requested flow rate 659.9 m³/h Actual flow rate 659.9 m³/h
Requested developed head 5.1 m Actual developed head 5.1 m
Pumped medium Water, rainwater Efficiency 72.0 %
with strainer Power absorbed 12.8 kW
Not containing chemical and Pump speed of rotation 865 rpm
mechanical substances which Shutoff head 8.0 m
affect the materials Design Single system 1 x 100 %
Ambient air temperature 20.0 °C Performance test No
Fluid temperature 20.0 °C
Fluid density 998 kg/m³
Design
Design Close-coupled submersible Material code (MS inboard) SIC/SIC/NBR
Orientation Vertical Impeller type Multivane radial flow impeller
Suction flange pump drilled unmachined (K)
according to(DN1) Wear ring Casing wear ring
Discharge flange pump drilled EN 1092-2 / DN 300 / PN 10 Impeller diameter 340.0 mm
according to(DN2) Free passage size 135.0 mm
Shaft seal 2 mech. seals in tandem Direction of rotation from drive Clockwise
arrangement with oil reservoir
Manufacturer KSB
Type (MS inboard) MG
Driver, accessories
Driver type Electric motor Motor service factor 1.15
Model (make) KSB Temperature sensor Bimetal switch 2x
Motor const. type KSB Sub. motor Motor winding 440 V
NEMA code letter C Number of poles 8
Designed for operation with Yes Starting mode Direct-on-line starting
frequency inverter Connection mode Delta
Frequency 60 Hz Motor cooling method Surface cooling
Rated voltage 440 V Motor version U
Rated power P2 16.4 kW Cable design Rubber hose
Available reserve 28.09 % Cable entry Sealed along entire length
Rated current 34.0 A Power cable AWG 11-7+15-5
Starting current ratio 3.1 Number of power cables 1
Insulation class F to IEC 34-1 Moisture sensor With
Motor enclosure IP68 Cable length 10.00 m
Cos phi at 4/4 load 0.77
Motor efficiency at 4/4 load 82.7 %
Data sheet
Materials G
Notes O-Ring (412) Nitrile rubber NBR
General criteria for a water analysis: pH-value >= 7; chloride Casing wear ring (502.1) Cast iron A 48 Class 35 B
content (Cl) <=250 mg/kg. Chlorine (Cl2) <=0.6 mg/kg. Motor housing (811) Cast iron A 48 Class 35 B
Pump casing (101) Cast iron A 48 Class 35 B Motor cable (824) Chloroprene rubber
Discharge cover (163) Cast iron A 48 Class 35 B Screw (900) Stainless steel A 193 B8M
Shaft (210) Chrome steel A 276 Type 410
T
Impeller (230) Cast iron A 48 Class 35 B
Packaging
Packaging category B2 With desiccants in PE- Packaging for storage Indoor
plastic sheeting, heat-sealed Outdoor storage at -40°C to +50°C, up to 12 months. Packet
water-proof, in must be covered.
wooden/plywood case,
outdoor storage up to 12
months
Packaging for transport Ship
IPPC Standard ISPM 15 Yes
Nameplates
Nameplates language International Duplicate nameplate With
Installation parts
Installation type Stationary with guide wire Type Chain
Scope of supply Pump with installation parts Material CrNiMo steel 1.4404
Installation depth 4.50 m Length 5.00 m
Material concept G Max. load 850 kg
Duckfoot bend
Size DN 300
Flange design ASME
Duckfoot bend size (DN2 / DN 300 Drilled according to
DN3) ASME
Material Cast iron A 48 Class 35 B
Mounting type Composite anchor bolts
Foundation rail Without
Claw
Design straight
Size DN 300
Coating
KSB coating code A1 to AA-0080-06-01 / 1 Final coating 2-component epoxy resin high
Surface preparation Free from dirt, grease, rust solid
Primer Zinc phosphate synthetic Color Ultramarine blue (RAL 5002)
resin KSB-blue
Total film thickness approx. 150 µm
Performance curve
Qmin
10
Total developed head
[m] Qmin
Qmin
5 ø408.0/393.0/376.0/6°/A06
Qmax
ø375.0/340.0/327.0/14°/A06
ø367.0/331.0/327.0/14°/A06
[m]
NPSH req.
50
Efficiency
[%]
0
0 200 [m³/h] 400 600 800 1000 1200
14
Power Input
[kW]
10
8
0 200 [m³/h] 400 600 800 1000 1200
Flow
Curve data
Speed of rotation 865 rpm Efficiency 72.0 %
Fluid density 998 kg/m³ Power absorbed 12.8 kW
Viscosity 1.00 mm²/s NPSH req. 3% 3.9 m
Flow rate 659.9 m³/h Curve number K43039s
Requested flow rate 659.9 m³/h Effective impeller diameter 340.0 mm
Total developed head 5.1 m Acceptance standard Tolerances to ISO 9906
Requested developed head 5.1 m Class 3B; below 10 kW
acc. to paragraph 4.4.2
Installation plan
300
250
150 100
ø 18
150 ø 10
1488
420
1265
1065
330
1240
DN3
1) (Lifting bail optional)
1068
840
min 800
440
DN1
ø 28
320
210
180 400 410
1711
1) Minimum water level t1
530
495
850 min 950 420
Access opening
min 1350
Motor Connections
Motor manufacturer KSB Suction flange pump drilled unmachined
Motor size 17 according to(DN1)
Motor power 16.4 kW Duckfoot bend size (DN2 / DN 300 Drilled according to
Number of poles 8 DN3) ASME
Speed of rotation 855 rpm
Weight net
Pump, Motor, Cable 715 kg
Claw / Foot 110 kg
Total 825 kg
Connect pipes without stress or strain! For auxiliary connections see
Dimensional tolerances for shaft axis height: DIN 747 separate drawing.
Dimensions without tolerances, middle tolerances to: ISO 2768-m
Connection dimensions for pumps: EN735
Dimensions without tolerances - welded parts: ISO 13920-B
Dimensions without tolerances - gray cast iron parts: ISO 8062-CT9