Professional Documents
Culture Documents
E
CONTENTS
SERVICE INFORMATION ............................ 3 FRONT DOOR FINISHER ................................. 16 F
Component ..............................................................16
MODIFICATION NOTICE .................................... 3 Removal and Installation .........................................16
Major Modification Notice .......................................... 3 G
REAR DOOR FINISHER ................................... 17
PRECAUTIONS ................................................... 4
Precaution for Supplemental Restraint System DOUBLE CAB ............................................................17
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- DOUBLE CAB : Component ....................................17 H
SIONER" ................................................................... 4 DOUBLE CAB : Removal and Installation ...............17
Precaution for Procedure without Cowl Top Cover...... 4
KING CAB ..................................................................17
Precaution for Work .................................................. 4 EI
KING CAB : Component ..........................................18
PREPARATION ................................................... 5 KING CAB : Removal and Installation .....................18
Commercial Service Tool .......................................... 5
BODY SIDE TRIM ............................................. 19 J
FRONT BUMPER ................................................ 6 Component ..............................................................19
Component ................................................................ 6 Removal and Installation .........................................20
Removal and Installation ........................................... 7 K
BACK SIDE TRIM ............................................. 22
REAR BUMPER .................................................. 8 DOUBLE CAB ............................................................22
Component ................................................................ 8
DOUBLE CAB : Component ....................................22 L
Removal and Installation ........................................... 8
DOUBLE CAB : Removal and Installation ...............22
FRONT GRILLE .................................................. 9 KING CAB ..................................................................22
Component ................................................................ 9 KING CAB : Component ..........................................23 M
COWL TOP .........................................................10 KING CAB : Removal and Installation .....................23
Component .............................................................. 10 SINGLE CAB .............................................................23
Removal and Installation ......................................... 10 SINGLE CAB : Component .....................................24 N
SINGLE CAB : Removal and Installation .................24
FENDER PROTECTOR ......................................11
Component .............................................................. 11 FLOOR TRIM .................................................... 25 O
MUDGUARD .......................................................12 DOUBLE CAB ............................................................25
Component .............................................................. 12 DOUBLE CAB : Component ....................................25
P
RUNNING BOARDS ...........................................13 KING CAB ..................................................................25
Component .............................................................. 13 KING CAB : Component ..........................................26
Removal and Installation ......................................... 14
SINGLE CAB .............................................................26
DOOR OUTSIDE MOLDING ..............................15 SINGLE CAB : Component .....................................27
Component .............................................................. 15
Removal and Installation ......................................... 15 HEADLINING .................................................... 28
EI
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SUPPLEMENTAL
RESTRAINT SYSTEM” and “SEAT BELTS” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SUPPLEMENTAL RESTRAINT SYSTEM”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Procedure without Cowl Top Cover INFOID:0000000003810993
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
PIIB3706J
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
B
Tool name Description
C
Engine ear
Locating the noise
D
SIIA0995E
PIIB1407E G
H
Remover tool Remove the clip and pawl and metal clip
EI
PIIB7923J
JMKIA1625ZZ
1. License plate bracket 2. Front air spoiler (center) 3. Front air spoiler (side) RH
4. Front bumper fascia 5. Front bumper side bracket A (RH) 6. Front bumper side bracket B (RH)
7. Rivet 8. Front fog lamp assembly 9. Front bumper retainer
10. Front bumper side bracket B (LH) 11. Front bumper side bracket A (LH) 12. Front air spoiler (side) LH
13. Front engine under cover 14. Front fog lamp opening finisher
Refer to GI-7, "Component" for symbols in the figure.
EI
L
JMKIA1626ZZ
REMOVAL
CAUTION:
• Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
• When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
MIIB9225E
1. Rear bumper reinforcement 2. Rear bumper carriage nut 3. Upper step pad
4. Rear bumper assembly 5. Carriage bolt 6. License lamp gasket
7. License lamp RH/LH 8. Lower step pad
REMOVAL
CAUTION:
• Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
• When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
EI
PIIB9550E
RHD models
PIIB9551E
INSTALLATION
CAUTION:
• When installing cowl top cover, make sure that blind clips are securely fitted in panel holes on body,
and then press them in.
• After installing, perform adjustment of wiper arms. Refer to WW-16, "Removal and Installation of
Front Wiper Arms, Adjustment of Wiper Arms Stop Location".
EI
MIIB9055E
JMKIA1627ZZ
P
JMKIA1628ZZ
EI
MIIB9126E
REMOVAL
CAUTION:
When removing running boards, 2 workers are required so as to prevent it from dropping.
INSTALLATION
CAUTION:
When installing running boards, 2 workers are required so as to prevent it from dropping.
EI
J
PIIB9552E
1. Front door outside molding 2. Front door assembly 3. Rear door outside molding (King K
cab)
4. Rear door assembly (King cab)
Refer to GI-7, "Component" for symbols in the figure. L
M
REMOVAL
CAUTION:
Be careful not to damage the body.
N
RHD models
PIIB9553E
REMOVAL
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
INSTALLATION
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
EI
PIIB9554E
K
1. Rear door 2. Pull handle escutcheon 3. Pull handle cover
4. Ashtray 5. Power window switch finisher 6. Armrest
L
7. Rear door finisher 8. Rear door handle bracket 9. Inner seal
: Clip
: Pawl M
N
REMOVAL
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
O
INSTALLATION
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then P
press them in.
KING CAB
PIIB9555E
REMOVAL
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth before remove.
INSTALLATION
CAUTION:
When installing door finisher, check that clips are securely fitted in panel holes on body, and then
press them in.
Double Cab B
EI
PIIB9556E
N
1. Center pillar upper garnish 2. Center pillar assist grip 3. Rear body side welt
4. Rear kicking plate 5. Center pillar lower garnish 6. Front body side welt
7. Front kicking plate 8. Dash side lower finisher 9. Dash side upper finisher O
10. Front pillar garnish 11. Front pillar assist grip 12. Side defroster grille
: Clip
: Pawl
P
: Metal clip
PIIB9557E
REMOVAL
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• Be careful not to damage the body.
• When removing or installing body side welts, never allow butyl seal to come in contact with pillar
garnish.
INSTALLATION
EI
PIIB9558E
1. Back pillar upper garnish 2. Back panel garnish 3. Air drafter assembly
4. Back panel finisher 5. Back pillar lower garnish
: Clip
: Pawl
: Metal clip
REMOVAL
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• Be careful not to damage the body.
• When removing or installing body side welts, never allow butyl seal to come in contact with pillar
garnish.
INSTALLATION
CAUTION:
When installing body side and backside trim, check that clips are securely fitted in panel holes on
body, and then press them in.
KING CAB
EI
PIIB9559E
J
1. Lock pillar upper garnish 2. Back panel garnish (side) RH 3. Back panel garnish (center)
4. Back panel garnish (side) LH 5. Air drafter assembly 6. Back panel finisher
7. Lock pillar lower garnish
K
: Clip
: Pawl L
: Metal clip
REMOVAL
CAUTION: N
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• Be careful not to damage the body.
• When removing or installing body side welts, never allow butyl seal to come in contact with pillar
garnish. O
INSTALLATION
CAUTION:
P
When installing body side and backside trim, check that clips are securely fitted in panel holes on
body, and then press them in.
SINGLE CAB
JMJIA1794ZZ
1. Lock pillar upper garnish RH 2. Lock pillar lower garnish RH 3. Lock pillar lower garnish LH
4. Lock pillar upper garnish LH 5. Back panel garnish
: Clip
: Pawl
: Metal clip
REMOVAL
CAUTION:
• Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
• Be careful not to damage the body.
• When removing or installing body side welts, never allow butyl seal to come in contact with pillar
garnish.
INSTALLATION
CAUTION:
When installing body side and backside trim, check that clips are securely fitted in panel holes on
body, and then press them in.
EI
PIIB9560E K
KING CAB L
RHD models
PIIB9561E
SINGLE CAB
A
RHD models
EI
JMJIA1795ZZ J
RHD models
PIIB9562E
REMOVAL
CAUTION:
• Always use SST, and attach a cloth to protect from damage.
• Disconnect negative battery terminal in advance.
• When removing, 2 workers are required. (1 for each front and rear of headlining)
• Never bend headlining when removing.
INSTALLATION
RHD models
C
EI
M
PIIB9563E
REMOVAL
CAUTION:
• Always use SST, and attach a cloth to protect from damage.
• Disconnect negative battery terminal in advance.
RHD models
JMJIA1796ZZ
REMOVAL
CAUTION:
• Always use SST, and attach a cloth to protect from damage.
• Disconnect negative battery terminal in advance.
EI
PIIB9564E
REMOVAL
CAUTION:
Be careful not to damage the body.