Professional Documents
Culture Documents
owner's manual
1
Before cleaning, be sure to stop the operation, turn the
breaker off or pull out the supply cord. 2. PARTS NAMES
Otherwise, an electric shock and injury may result. 5
After a long use, check the unit stand and fitting for 4 Fig.2-1
damage.
If damaged, the unit may fall and result in injury.
1 Air inlet (Both in Left and right sides, as well as in rear side. )
To avoid oxygen deficiency, ventilate the room 2 Refrigerant pipe connective opening
sufficiently if equipment with burner is used together
with the air conditioner. 3 Wires outlet (Some types have not wires outlet)
4 Fixed foot
Arrange the drain hose to ensure smooth drainage.
Air outlet (Heat air to be blows out in the cooling operation,
Incomplete drainage may cause wetting of the building, 5
vice versa while the heating. )
furniture etc.
owner's manual
2
3. When the Priority Mode has been set, the first indoor unit will
Protection Device
work in Heating Mode that is Heating Priority, please refer to the
This protection device will stop the unit automatically in case
ITEM 1 for the control logic. If the first indoor unit is work in
the air conditioner is on forced running mode. When protection
Cooling Mode, that is the Cooling Priority Mode, please refer to
device is activated, running indicator light is lightened and
the ITEM 2 for the control logic;
query light flashes.Protection device may start under the
4. In terms of the settings only respond the Heating Mode, the following circumstances:
indoor unit will run in Heating Mode normally, if unit be run in the
Cooling Mode or air Supply Mode, the indoor unit will display cooling operation:
Mode Conflicting;
● The air inlet or air outlet of outdoor unit is blocked.
5. In terms of the settings only respond the Cooling Mode, the
indoor unit will run in Cooling Mode or air supply mode normally, if ● Strong wind is continuously blowing to the air outlet of the
unit be run in the Heating Mode, the indoor unit will display Mode outdoor unit.
Conflicting.
heating operation:
Features of heating operation
● Too much dust and rubbish adhere to the dust filter in the
● Warm air will not be blown out immediately at the beginning of the indoor unit
heating operation, after 3~5minutes (depends on the indoor and
outdoor temperature), until the indoor heat exchanger become Power cut
hot, then blows out warm air.
● If power is cut during operation, stop all the operation
● During operation, the fan motor in the outdoor unit may stop
immediately.
running under high temperature.
● Power comes again. The operation indicator on the wire
● During Fan operation, if other indoor Units are running on heating controller flashes.
mode, the fan may stop in order to prevent sending heat wind.
Defrost in the heating operation ● Push the ON/OFF button again if you want to restart the
unit.
● During heating operation, outdoor unit sometimes will frost. To
increase efficiency, the unit will start defrosting automatcally Mishanding in operation
(about 2~10 minutes), and then water will be drained out from In case of mishandling caused by lighting or mobile wireless,
outdoor unit. please switch off the manual power off the manual power.
Push ON/OFF again when restarting.
● During defrosting, both the fan motors in the outdoor unit and
indoor unit will stop running. Heating capacity
Operation conditions ● The heating process is :absorb heat from outdoor, while
For proper performance, run the air conditioner under the expel heat to indoor by hot pump. Once the outdoor
following temperature conditions: temperature drop down, heating capacity is degraded
correspondingly.
Table.3-1
Temperature ● It is command to equip with other warming facility, when
Outdoor Indoor Room relative outdoor temperature is low.
Mode temperature temperature humidity
● It is better to equip with additional purchase indoor
Room
Cooling mode auxiliary heating device in paramos area where is in
-5°C ~ 48°C 17°C ~ 32°C below 80%
particularly low outdoor temperature.(See Indoor Unit
Heating mode Operation Manual for detail information)
-15°C ~ 24°C ≤27°C
(Cooling only type without)
NOTE NOTE
Protective device may start if running the unit outside the Please switch off the power when protection device starts.
above condition, which will prevent the unit from operation. Do not restart until the problems are solved.
CAUTION
owner's manual
3
Please read the following illustration(before apply for servicing) Table.4-1
Troubles Causes
Outdoor unit
FAN function stop automatically to defrost. It is
White mist or water
the start and stop sound of the solenoid valve
The sound of “hiss”
At the beginning and the end of the running
process, sounds like water flow in valve occurs,
which will be amplified in 3~15 minutes, this is
caused by dehumidifying process of refrigerant
current.
Not malfunction Indoor unit Pieces of the wall, carpet, furniture, cloth,
Bad odor cigarette, cosmetics are adhere to the unit.
Operation lamp flashes Switch on the power after the power cut.
Check it again
owner's manual
4
5. MALFUNCTION
Malfunction display of outdoor nuit’s DSP1
Table.5-1
No. Error code Error or protection type Note
4 E3 Reserve
5 E4 The pipe temp. sensor (for sensing the ambient temp. ) error
6 E5 Reserve
7 E6 Reserve
15 H5 P2 protection occur 3 times within 30 minutes Must be re-powered on for the recovery
16 H6 P4 protection occur 3 times within 100 minutes Must be re-powered on for the recovery
30 L0 Modual error
31 L1 Lo. voltage protection of DC main lead
32 L2 Hi. voltage protection of DC main lead
33 L3
34 L4 MCE error / synchro / closed loop
36 L6
37 L7 Phase sequency error protection
If the problem still existing, please contact the sales distributor or the service center, tell us your model No. and the detail of the
error.
owner's manual
5
6. CONSTRAINT COOLING AND QUERY
MAIN BOARD
(OUTDOOR UNIT)
Query button
Constraint Cooling
Once pressing the constraint cooling button(see the chart on the Constraint cooling button
right), all the indoor unit will be on forced cooling mode and the
wind speed is HIGH.
CHECK COOL
Fig.6-1
Query
Table 6-1
Normal display Display content Note
7 Operation mode 0, 1, 2, 3, 4
23 The last time error orprotective code Without protection or error displays as 00
owner's manual
6
7. AFTERSALE SERVICE
If the air conditioner was operate abnormally, please plug
off the power supply firstly, and contact with After-sales
Center or Special Distributor. For detail please refer to the
attached accessory Consumer Service Instruction.
owner's manual
7
MDV09U-020IW
202000171469
版本更换明细(本页不出菲林,仅作文档说明)
A升级B
1、更改第三页中Table3-1的温度值更改。
2、最后一页更换版本号。
B升级C
1、第一页与第二页按认证要求增加相关内容
2、最后一页更换版本号。
C升级D
1、第5页增加15和16点的H5\H6描述.
2、最后一页更换版本号。
D升级E
1、第2、5、7页删除midea字样.
2、最后一页更换版本号。
E升级F
1、封面修改说明书名称,且右下角增加注意事项的说明;
2、第1页右下角CAUTION部分增加与封面注意事项一样的说明;
3、第2页CAUTION部分内容调整顺序;
4、第3页Table.3-1中Heating mode下增加“Cooling only type without”,并取消压缩机限频图;
5、第6页3-Heating后面增加(Cooling only type without);
6、第7页将AFTERSALE SERVICE下面的内容改到左侧;
7、封底升级版本号。
F升级G
1、第一页 near the coast 后面增加 except for the models with corrosion-resistant function。
2、封底版本号升级。
G升级H
1、第二页 外观示意图更换为880新结构。
2、封底版本号升级。
H升级I
1、根据营销公司要求产品中不出现在“V4+”字样,更改说明书封面产品的描述.
2、封底版本号升级。