You are on page 1of 24

Process engineering

Collection and disposal of commercial food waste


ACO Waste-Jet – Wet refuse collection system
ACO. The future
of drainage.

The ACO system chain provides drainage solutions to meet


tomorrow‘s environmental challenges
The increase in extreme weather conditions requires more complex approaches to
water drainage. ACO provides smart system solutions which work in both directions:
They protect people from water – and vice versa. Each ACO product within the ACO
system chain sends the water in the right direction, with the aim of being able to re-
cycle it in a way that makes sense both ecologically and economically. Within the
ACO group it is ACO Haustechnik which supports the overall system chain, and com-
bines system solutions for drainage, separation and pumping in order to create total
drainage solutions for buildings.

collect: clean: hold: release:


Collect and store Pre-clean and treat Keep away from Pump, drain and re-use
and hold back

Floor drainage systems Grease separators Backflow systems Lifting plants


Bathroom drainage Starch separators Pumping stations
Roof drainage Light oil separators
Multi-storey parking Process technology
deck drainage
Balcony and terrace
Drainage pipe systems

The ACO system


chain in action
Filling the collection station Temporary storage in tanks Emptying into the suction vehicle

Every product from ACO Haustechnik integrates into the ACO system chain

Contents
ACO Waste-Jet wet refuse collection system – ACO Waste-Jet
Collection and disposal of commercial food waste ACO System chain for drainage
4
While metal and plastic waste can be disposed of without problems, kitchen waste has of commercial kitchens
to be stored and disposed of separately. Commercial food waste is normally collected in Traditional waste disposal and
6
drums, which need to be stored in cold rooms to avoid smells and rodent infestation. At modern waste management
regular intervals these are then removed by a specialist disposal company. Function 8
Product overview 11
Handling commercial food waste costs time and money. In addition, hygiene concerns defi- ACO Waste-Jet Comfort type 3 12
nitely apply. By using a system to collect and dispose of commercial food waste the cost ACO Waste-Jet Comfort type 6 14
can, however, be significantly reduced. ACO wet refuse technology is presented in detail ACO Waste-Jet OD Classic 16
below. ACO Waste-Jet OA Classic 18
ACO Waste-Jet OAE Classic 20
Collection stations/Accessories 22
Process engineering

The ACO system chain at work in the domain

of total drainage of commercial kitchens

Disposal

Wet refuse collection system Wet refuse collection system


ACO Waste-Jet Comfort ACO Waste-Jet Classic

Kitchen design in commercial kitchens is stainless steel Disposal of food waste


Kitchen design is a diverse and complex (material grade 304 or 316). Its main Wherever meals are prepared organic
process. The wastewater has to be col- benefits are its smooth surface and its waste is created from the preparation
lected using drainage channels, floor robustness. and the consumption of meals. This is
4 gullies and pipework systems and then normally collected in drums, which need
fed into the sewers through grease sep- Wastewater processing to be stored in cold rooms to avoid
arators. Special attention needs to be Kitchen wastewater generally contains smells and rodent infestation. This kind
paid to the collection and transmission grease and so needs to be cleaned. of disposal costs time and money.
of food waste. Here ACO can literally Wastewater which contains grease is a
offer a one-stop solution. threat to pipes, drainage elements and By installing an ACO Waste-Jet system,
sewers. the collection and disposal of commer-
Kitchen drainage cial food waste is not only dealt with
Whether for renovations or new projects, Grease and oils are deposited with professionally, but also ecologically and
ACO can offer a complete range based other wastewater components on the hygienically, as the risk of cross-contam-
on a modular approach. Depending on walls of the pipes and lead to corrosion, ination is removed.
the quantity of water falling onto the blockages and noisome smells. ACO
surface to be drained, and the position Haustechnik has a wide range of grease
of the drainage elements, a combination separators available, either free-standing
of box channels, high capacity channels, or below ground. Free-standing grease
slot channels and floor gullies are used. separators are one of two kinds: full dis-
The material of choice for floor drainage posal or partial disposal.
Process engineering

Separate

Our Brochure “Grease separators”

Any business which creates wastewater


is required by law to ensure that any
substances and fluids which could cre-
ate blockages or smells do not reach
the public sewerage system. In order
ACO Variant-CR to ensure that organic fats and oils are
box channels held back as required, grease separa-
tors are used in kitchens, meat-process-
ing businesses and a very wide variety
ACO Hydrojet Grease of foodstuff producers.
separator connected
to an ACO wastewa-
ter Muli-Mini duo
lifting plant

Storage and processing Our Brochure “Stainless steel


floor gullies and channels”

Wastewater drops onto the floor during


the storage and preparation of food- 5
stuffs In a commercial area this must
always be drained off through hygieni-
cally impeccable drainage systems. For
this, generally floor gullies, box chan-
nels, high-capacity channels and slot
channels made from stainless steel are
used. Depending on the type of applica-
ACO Variant-CR tion there are various different gratings
box channels available.
ACO Variant-CR
high-capacity channels
ACO Variant-CR
floor gullies
ACO Variant-CR
slot channels
Process engineering

Traditional waste disposal in commercial kitchens

using bins and wet waste coolers

Waste Foodstuffs

Dirty Clean

Wastewater Fresh water

The use of normal waste buckets and For example, when carrying the waste In order to avoid unpleasant odours
bins to store and dispose of kitchen bin with the wet waste out of the clean from the organic waste collection bins
waste of animal and plant origin (wet area to the organic waste collection bins these then need to be stored, with the
waste) carries with it a significant risk to in the unclean area there is a risk of attendant energy costs, in chilled rooms
the problem-free and responsible man- cross contamination, because this offers until they are disposed of by an expert
agement of a commercial kitchen. micro organisms a route into preparation company.
areas in the kitchen.
Some degree of chilling of kitchen waste
also needs to be applied for temporary
storage in wet waste cool boxes.
Process engineering

Modern refuse management using

ACO Waste-jet wet refuse collection systems

Waste Foodstuffs

Clean

Wastewater Fresh water

The use of the ACO Waste-Jet wet refuse The kitchen waste is transported from As the tanks used in the ACO Waste-Jet
collection system creates a closed its point of origin via a collection station wet refuse collection systems are sealed
hygiene chain from the point of origin directly into a tank. and odour-proof containers, no further
of the kitchen wastes to disposal by a chilling of the wet waste is required. In
specialist company. So no waste bins need to be provided addition, these benefits also mean that
in the kitchen, meaning that cross-con- the time lapse between each emptying
tamination during their removal from the of the tank is considerably longer when
clean area is eliminated. compared to the use of organic waste
collection bins.
Process engineering

How the ACO Waste-Jet wet refuse collection system works

Input
Kitchen waste of animal or plant origin (wet refuse) that is created during the preparation of meals or when clearing away dishes,
is removed through a collection station right where it is created in the kitchen, or next to the dishwasher.
Free-standing or built into the worktop
Fully automatic operation

Shredding and transporting


With added water, the food waste is finely shredded and prepared to be moved on into the tank. The drawing off of the wet waste
from the collection station is done by either a pneumatic pressure system or a feed pump, depending which system you select.
Effective shredding and homogenising
Integrated safety mechanisms
Process engineering

Temporary storage
The wet waste is stored in the collection tank until the tank’s maximum storage capacity is reached. The fact that the tank is full is
displayed visually at the collection station.
  Flexible, odour-proof tank system
  Compact construction without pressure, easy to install

Disposal
The contents of the tank are pumped directly into a disposal vehicle via a draw-off connection.
Then the system is ready to use once again.
  High pressure internal cleaning for odourless cleaning of the container.
  Feed pump for reliable disposal over lengthy pipes.
Process engineering

10
Process engineering

Product overview

Wet refuse collection systems

Tank
The tanks for temporary storage in the The fill-level monitoring is done using
ACO Waste-Jet system may be made monitoring systems which are integrated
from either stainless steel (grade 304) in the tank. All containers are sealed
or plastic (polyethylene). to be odour-free and have inspection
hatches for maintenance.
Depending on the application and the
selected material, the tanks come in dif-   Page 12
ferent sizes and versions (high-pressure
internal cleaning, disposal pump etc.).

Collection station 11
In the ACO Waste-Jet system the tanks The collection stations for the Waste-Jet
are filled using collection stations. Comfort system transfer the wet waste
to the tank using a vacuum system,
These collection stations can, depending while the Waste-Jet Classic system uses
on requirements, by installed free-stand- feed pumps. When the tank is full this
ing in the kitchen and next to dishwash- is displayed visually at the collection
ers, or can built into work-surfaces. station.

  Page 22
Process engineering

ACO Waste-Jet Comfort type 3

Product information

ACO Product benefits ■ Optionally with


 Total system control via a touch
■ Hygienic collection and disposal
panel
 No need for cold storage
 Remote diagnosis
 No interim storage in drums is
 Connection to building control sys-
necessary
tem/central technical supervision
■ modular construction
■ 3 vacuum connections
 Takes up little space
 Pneumatic valve DN 50
 Easy to transport and mount
 vacuum created using ejector
■ Hydro-mechanical high-pressure
■ Stainless steel, material grade 316
cleaning at 175 bar
■ For installation in frost-free environ-
 Only cold-water feed needed
ment
 Built-in automatic sludge liquor
■ Emptying connection, fire hose quick
draining
coupling B 2½”
 Reduced volumes to dispose of
■ Disposal pump
■ Integrated disposal pump
■ Hydro-mechanical high pressure
 Pressure and vacuum operation
internal cleaning
■ Nominal pressure: 175 bar
■ capacity: 13 l/min
■ Food waste collection tank for con-
■ circulation pump
nection to ACO Waste-Jet collection
 20 m3/h bei 1 bar
station and/or ACO Grease separa-
■ Sludge measurement
tor, compliant with DIN EN 1825/DIN
■ sludge liquor draw-off pump
4040-100 for NS 2 – 25
 12 m3/h at 0.5 bar
■ Completely sealed odour-proof instal-
■ 1-stage piston compressor
lation
■ Pressure container: 250 l
■ Fully automatic controls
■ suction volume: 660 l/min
■ Incident warnings using volt free
■ motor power: 3 kW
contacts
■ Electrical connection for total system
controls

12

Possible arrangements for


low-pressure connectors (1–3)

Option 1: Option 2:

A
1 2 3
A
1 1
A
2
2
A
3 ACO Waste-Jet
B
Type 3

3
Waste
Fats
Sludge A = collection station B = grease separator
Process engineering

Dimensions Type 3

Discharge connection with Max. segment height

500
Min 150
fire-hose quick connector (without extensions)

min.
2 1/2 DIN 14308

950 x 650 800,210


800, 210tief
deep

Touch panel
(Option)

890

1.000
Sludge measurement
H3

2.000
H2

H1

Total system controls


(mounted on container or wall)
High pressure pump

Sludge liquor draw-off pump


Circulation pump

Piston pump
Draining/ ØD
discharge pump Max. RR
max.

Maintenance hatch HD orbital spray head


LW diameter 500

Vent connection for pump truck


R2½

Level detection via


dynamic pressure reading

3 vacuum connections

13

Product parameter Type 3

Useful Dimensions Weight Type 3


ACO volume Diam R H1 H2 H3 empty full
Waste-Jet
[l] [mm] [mm] [mm] [mm] [mm] [kg] [kg]
2.500 1.500 1.250 1.800 2.000 2.200 580 3.080
3.300 1.500 1.250 2.100 2.300 2.500 650 3.950
Type 3
4.400 1.750 1.400 2.300 2.500 2.700 690 5.100
6.000 1.750 1.400 3.000 3.200 3.400 760 6.750

Order information Type 3

Useful
ACO Included in volume Suitable for
Art. no.
Waste-Jet product grease separator NS ...
[l]
2.500 2 To 4 7950.00.00
3.300 5,5 To 8,5 7950.00.01
Manual switch
4.400 10 To 15 7950.00.02
6.000 20 To 25 7950.00.03
Type 3
2.500 2 To 4 7950.01.00
3.300 5,5 To 8,5 7950.01.01
Touch panel
4.400 10 To 15 7950.01.02
6.000 20 To 25 7950.01.03
Process engineering

ACO Waste-Jet Comfort type 6

Product information

ACO Product benefits ■ Optionally with


 Total system control via a touch
■ Hygienic collection and disposal
panel
 No need for cold storage
 Remote diagnosis
 No interim storage in drums is
 Connection to building control sys-
necessary
tem/central technical supervision
■ modular construction
■ 6 vacuum connections
 Takes up little space
 Pneumatic valve DN 50
 Easy to transport and mount
 vacuum created using ejector
■ Hydro-mechanical high-pressure clean-
■ Stainless steel, material grade 316
ing at 175 bar
■ For installation in frost-free environ-
 Only cold-water feed needed
ment
 Built-in automatic sludge liquor
■ Emptying connection, fire hose quick
draining
coupling B 2½”
 Reduced volumes to dispose of
■ Disposal pump
■ Integrated disposal pump
 20 m3/hr at 1 bar
 Pressure and vacuum operation
■ Hydro-mechanical high pressure
internal cleaning
■ Wet waste collection tank for con- ■ Nominal pressure: 175 bar
nection to ACO Waste-Jet collection ■ capacity: 13 l/min
station and/or ACO Grease separator, ■ circulation pump
compliant with DIN EN 1825/  20 m3/hr at 1 bar
DIN 4040-100 for NS 2 – 25 ■ Sludge measurement
■ Completely sealed odour-proof instal- ■ sludge liquor draw-off pump
lation  12 m3/hr at 0.5 bar
■ Fully automatic controls ■ 2-stage piston compressor
■ Incident warnings using volt free ■ Pressure container: 500 l
contacts ■ suction volume: 750 l/min
■ motor power: 5.5 kW
■ Electrical connection for total system
controls

14 Possible arrangements for


low-pressure connectors (1–6)

Option 1: Option 2: Option 3: Option 4:

A A 1
A
1 1 1
A A A B
2 2 2
A A 2
3 3
A A
4 4 3 3
A
5 5 B B

A
6 B
4 4

6 5 5

1 2 3 4 5 6 B B

6 6

ACO Waste-Jet Waste

Type 6 Fats
Sludge

A = collection station B = grease separator


Process engineering

Dimensions Type 6

Discharge connection with Max. segment height

500
Min 150
fire-hose quick connector (without extensions)

min.
2 1/2 DIN 14308

1.000 x 950 800,210


800, 210tief
deep

Touch panel
(Option)

890

1.000
Sludge measurement
H3

2.150
H2

H1

Total system controls


(mounted on container or wall)
High pressure pump

Sludge liquor draw-off pump


Circulation pump

Piston pump
Draining/ ØD
discharge pump Max. RR
max.

HD orbital spray head 3 vacuum connections

Maintenance hatch
LW diameter 500 Vent connection for pump truck
R2½

Level detection via


dynamic pressure reading

3 vacuum connections

15

Product parameter Type 6

Useful Dimensions Weight Type 6


ACO volume Diam R H1 H2 H3 empty full
Waste-Jet
[l] [mm] [mm] [mm] [mm] [mm] [kg] [kg]
2.500 1.500 1.250 1.800 2.000 2.200 670 3.150
3.300 1.500 1.250 2.100 2.300 2.500 690 3.990
Type 6
4.400 1.750 1.400 2.300 2.500 2.700 800 5.200
6.000 1.750 1.400 3.000 3.200 3.400 880 6.880

Order information Type 6

Useful
ACO Included in volume Suitable for
Art. no.
Waste-Jet product grease separator NS ...
[l]
2.500 2 To 4 7950.02.00
3.300 5,5 To 8,5 7950.02.01
Manual switch
4.400 10 To 15 7950.02.02
6.000 20 To 25 7950.02.03
Type 6
2.500 2 To 4 7950.03.00
3.300 5,5 To 8,5 7950.03.01
Touch panel
4.400 10 To 15 7950.03.02
6.000 20 To 25 7950.03.03
Process engineering

ACO Waste-Jet OD Classic

Polyethylene wet waste collection tank

Product information

ACO Product benefits ■ DN 65 drainage connector for direct


pumping
■ Hygienic collection and disposal
■ Rinsing by opening the cover
■ No need for cold storage
■ For installation in frost-free environment
■ No interim storage in drums is
■ Polyethylene collection tank
necessary
■ DN 40 connection option for
■ Compact installation
connection to collection station
■ Structural stability with proof of
■ Fill level monitoring
stability for over 25 years
■ DN 100 ventilation connection
■ Two maintenance hatches 450 mm
diameter sealed with tension ring
against odours

16
Process engineering

Dimensions of base model


with direct draw-off

HH

LLxxW B Lx

Order information ACO Waste-Jet OD Classic

ACO Useful Dimensions Weight


Waste-Jet volume L W H empty full Art. no.
Classic [l] [mm] [mm] [mm] [kg] [kg]
OD 1 830 2.000 700 1.700 100 930 7950.10.00
OD 2 2.000 2.690 950 1.850 226 2.226 7950.11.00
17

Sludge liquor draw-off for Waste-Jet Classic

■■ To make optimum use of the capacity of Waste-Jet Classic‘s


tank volume
■■ Sludge liquor draw-off takes place in the ACO grease separator
■■ Including fixings and connectors
■■ With controls and centrifugal pump 0.37 kW, 230 V/50 Hz

Product Description Art. no.


Sludge liquor draw-off for ACO Grease separator DN 100, 150 or 200 0155.09.84
Connection set (T-junction and pipe connector) 0155.03.53 x 1
for connection to DN 100 grease separator 0150.24.92 x 2
Connection set (T-junction and pipe connector) 0155.03.54 x 1
for connection to DN 150 grease separator 0150.24.93 x 2
Connection set (T-junction and pipe connector) 0155.03.55 x 1
for connection to DN 200 grease separator 0150.24.94 x 2
Process engineering

ACO Waste-Jet OA Classic

Polyethylene wet waste collection tank

Product information

ACO Product benefits ■ DN 65 drainage connector for direct


pumping
■ Hygienic collection and disposal
■ 400 V/50 Hz/17 A/3.9 kW electrical
 No need for cold storage
connection
 No interim storage in drums is
■ For installation in frost-free environment
necessary
■ Polyethylene collection tank
■ Compact installation
■ DN 40 connection option for
■ Structural stability with proof of stabil-
connection to collection station
ity for over 25 years
■ Fill level monitoring
■ Fully automated hydro-mechanical high
■ DN 100 ventilation connection
pressure internal cleaning for disposal
■ Two maintenance hatches 450 mm
and cleaning using a cold-water con-
diameter sealed with tension ring
nection
against odours
■ High-pressure unit and wall-mounted
controls

18
Process engineering

Dimensions of extension level 1


with direct draw-off and high pressure internal cleaning

HH

LLxx WB LxB

Order information ACO Waste-Jet OA Classic

ACO Useful Dimensions Weight


Waste-Jet volume L W H empty full Art. no.
Classic [l] [mm] [mm] [mm] [kg] [kg]
OA 1 830 2.060 700 1.700 135 965 7950.10.01
OA 2 2.000 2.750 950 1.850 252 2.252 7950.11.01
19

Sludge liquor draw-off for Waste-Jet Classic

■■ To make optimum use of the capacity of Waste-Jet Classic‘s


tank volume
■■ Sludge liquor draw-off takes place in the ACO grease separator
■■ Including fixings and connectors
■■ With controls and centrifugal pump 0.37 kW, 230 V/50 Hz

Product Description Art. no.


Sludge liquor draw-off for ACO Grease separator DN 100, 150 or 200 0155.09.84
Connection set (T-junction and pipe connector) 0155.03.53 x 1
for connection to DN 100 grease separator 0150.24.92 x 2
Connection set (T-junction and pipe connector) 0155.03.54 x 1
for connection to DN 150 grease separator 0150.24.93 x 2
Connection set (T-junction and pipe connector) 0155.03.55 x 1
for connection to DN 200 grease separator 0150.24.94 x 2
Process engineering

ACO Waste-Jet OAE Classic

Polyethylene wet waste collection tank

Product information

ACO Product benefits ■ DN 65 drainage connector for direct


pumping
■ Hygienic collection and disposal
■ High-pressure unit and wall-mounted
 No need for cold storage
controls
 No interim storage in drums is
■ 400 V/50 Hz/17 A/6.9 kW electrical
necessary
connection
■ Compact installation
■ DN 65 drainage connector for direct
■ Structural stability with proof of stabil-
pumping
ity for over 25 years
■ Rinsing by opening the cover
■ Fully automated hydro-mechanical high
■ For installation in frost-free environment
pressure internal cleaning for disposal
■ Polyethylene collection tank
and cleaning using a cold-water con-
■ DN 40 connection option for
nection
connection to collection station
■ Automatic drainage pump, motor
■ Fill level monitoring
power: 3.0 kW/2850 rpm – delivery
■ DN 100 ventilation connection
performance: 20 m³/h at 1 bar me-
■ Two maintenance hatches 450 mm
dium delivery head
diameter sealed with tension ring
against odours

20
Process engineering

Dimensions of extension level 2


with drainage pump and high pressure internal cleaning

H
H

LLxx WB

Order information ACO Waste-Jet OAE Classic

ACO Useful Dimensions Weight


Waste-Jet volume L W H empty full Art. no.
Classic [l] [mm] [mm] [mm] [kg] [kg]
OAE 1 830 2.460 930 1.650 210 1.040 7950.10.02
OAE 1 2.000 3.150 1.180 1.850 337 2.337 7950.11.02
21

Sludge liquor draw-off for Waste-Jet Classic

■■ To make optimum use of the capacity of Waste-Jet Classic‘s


tank volume
■■ Sludge liquor draw-off takes place in the ACO grease separator
■■ Including fixings and connectors
■■ With controls and centrifugal pump 0.37 kW, 230 V/50 Hz

Product Description Art. no.


Sludge liquor draw-off for ACO Grease separator DN 100, 150 or 200 0155.09.84
Connection set (T-junction and pipe connector) 0155.03.53 x 1
for connection to DN 100 grease separator 0150.24.92 x 2
Connection set (T-junction and pipe connector) 0155.03.54 x 1
for connection to DN 150 grease separator 0150.24.93 x 2
Connection set (T-junction and pipe connector) 0155.03.55 x 1
for connection to DN 200 grease separator 0150.24.94 x 2
Process engineering

Collection station for ACO Waste-Jet Comfort axb

Separate collection station


Free-standing installation in the kitchen
Shredding and homogenising
Fill level detection
Rinsing nozzles in the collection funnel
Hand spray for manual cleaning

c
Hot and cold water connections R ¾”
Automatic controls
Electrical connection 400 V;
50 Hz/1.5 – 2.2 kW
IP 55 protection

Useful Dimensions Grinder Through- Weight


Type volume a b c performance put empty full Art. no.
[l] [mm] [mm] [mm] [kW] [kg/min] [kg] [kg]
F5 20 600 400 910 1,5 10–15 150 170 0150.33.94
F12 20 750 700 890 2,2 15–20 160 180 0150.33.95
F25 50 1.200 500 910 2,2 15–20 180 230 0150.33.96

axb

Separate collection station


for dishwasher
For fitting in the dishwashing line or
upstream of commercial dishwashers
Shredding and homogenising
Fill level detection
Rinsing nozzles in the collection funnel

c
Hot and cold water connections R ¾”
Automatic controls
Electrical connection 400 V; 50 Hz/1.5 kW
IP 55 protection

22 Useful Dimensions Grinder Through- Weight


Type volume a b c performance put Controls empty full Art. no.
[l] [mm] [mm] [mm] [kW] [kg/min] [kg] [kg]
S1 20 980 360 870 1,5 15–20 1x lengthwise 142 165 0150.44.56
S2 20 980 360 870 1,5 15–20 2x lengthwise 142 165 0150.44.57
Process engineering

Collection station for ACO Waste-Jet Classic

Separate collection station


■■ Stainless steel, (grade 304) ■■ Fill level detection
■■ Free-standing construction in frost- ■■ Rinsing nozzles in the collection funnel
free areas ■■ Hand spray for manual cleaning
■■ Useful volume 20 litres ■■ R ¾“ hot and cold water connections
■■ Shredding and homogenising, power: including mixer valve
1.5 kW (throughput: 10 kg/min.) ■■ Automatic controls
■■ With separate feed pump for wall ■■ Electrical connection 400 V;
mounting, DN 40 pressure connection 50 Hz/1.5 – 2.2 kW
■■ maximum length of pipe between feed ■■ IP 55 protection
pump and tank: 15 m ■■ Control on the front
■■ maximum length of pipe between feed
pump and tank: 50 m

Useful Dimensions Grinder Through- Weight


Type volume a b c performance put empty full Art. no.
[l] [mm] [mm] [mm] [kW] [kg/min] [kg] [kg]
F5 with pump 20 600 400 910 1,5 10–15 150 170 0150.45.74

Separate collection station


for dishwasher
■■ Stainless steel, (grade 304) ■■ Rinsing nozzles in the collection funnel
■■ Free-standing construction in frost- ■■ R ¾“ hot and cold water connections
free areas including mixer valve
■■ Useful volume 20 litres ■■ Automatic controls
■■ Shredding and homogenising, power: ■■ Electrical connection 400 V;
1.5 kW (throughput: 10 kg/min.) 50 Hz/1.5–2.2 kW
■■ With separate feed pump for wall ■■ IP 55 protection
mounting, DN 40 pressure connection ■■ Controls on both ends
■■ maximum length of pipe between feed
pump and tank: 15 m
■■ maximum length of pipe between feed
pump and tank: 50 m

23
Useful Dimensions Grinder Through- Weight
Type volume a b c performance put Controls empty full Art. no.
[l] [mm] [mm] [mm] [kW] [kg/min] [kg] [kg]
S2 with pump 20 980 360 870 1,5 15–20 2x lengthwise 142 165 0150.45.75

Accessories for ACO Waste-Jet Classic

Illustration Product Description Version Art. no.

Remote control
■■ To be fitted on site with a connection box
■■ Control line: 7 x 1.0 mm2 (on-site) Extension stage 3 0150.45.78
■■ IP 54 protection Extension stage 3E 0150.45.79

Connection box
■■ For evacuation connection and remote control
■■ Stainless steel, (grade 304) 7601.80.20
■■ Fixing: „On wall“
■■ Width x Depth x Height 500 x 160 x 500 mm

Flush frame
■■ For connection box 7601.80.20 7601.80.21
■■ Width x Depth x Height 565 x 15 x 565 mm
ACO. The future
of drainage.

Geb 132/04/2013 Subject to alterations

www.aco.com

You might also like