Professional Documents
Culture Documents
uk
4 3
2
1
9
6
5
UK
Ireland
Australia
New Zealand
Downloaded from www.Manualslib.com manuals search engine
13 11 12
5
6
A B
5
14 8
C D
7
15
3
9 10
E F
2
Downloaded from www.Manualslib.com manuals search engine
Intended use 3. Personal safety
Your Black & Decker drill/screwdriver has been designed for a. Stay alert, watch what you are doing and use common
screwdriving applications and for drilling in wood, metal and sense when operating a power tool. Do not use a
plastics. This tool is intended for consumer use only. power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
Safety instructions while operating power tools may result in serious personal
injury.
General power tool safety warnings b. Use personal protective equipment. Always wear eye
@
protection. Protective equipment such as dust mask,
Warning! Read all safety warnings and all non-skid safety shoes, hard hat, or hearing protection
instructions. Failure to follow the warnings and used for appropriate conditions will reduce personal
instructions listed below may result in electric shock, injuries.
fire and/or serious injury. c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
Save all warnings and instructions for future reference. and/or battery pack, picking up or carrying the tool.
The term "power tool" in all of the warnings listed below refers Carrying power tools with your finger on the switch or
to your mains operated (corded) power tool or battery energising power tools that have the switch on invites
operated (cordless) power tool. accidents.
d. Remove any adjusting key or wrench before turning
1. Work area safety the power tool on. A wrench or a key left attached to a
a. Keep work area clean and well lit. Cluttered or dark rotating part of the power tool may result in personal injury.
areas invite accidents. e. Do not overreach. Keep proper footing and balance at
b. Do not operate power tools in explosive atmospheres, all times. This enables better control of the power tool in
such as in the presence of flammable liquids, gases unexpected situations.
or dust. Power tools create sparks which may ignite the f. Dress properly. Do not wear loose clothing or
dust or fumes. jewellery. Keep your hair, clothing and gloves away
c. Keep children and bystanders away while operating from moving parts. Loose clothes, jewellery or long hair
a power tool. Distractions can cause you to lose control. can be caught in moving parts.
g. If devices are provided for the connection of dust
2. Electrical safety extraction and collection facilities, ensure these are
a. Power tool plugs must match the outlet. Never modify connected and properly used. Use of dust collection can
the plug in any way. Do not use any adapter plugs reduce dust-related hazards.
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock. 4. Power tool use and care
b. Avoid body contact with earthed or grounded a. Do not force the power tool. Use the correct power
surfaces such as pipes, radiators, ranges and tool for your application. The correct power tool will do
refrigerators. There is an increased risk of electric shock the job better and safer at the rate for which it was
if your body is earthed or grounded. designed.
c. Do not expose power tools to rain or wet conditions. b. Do not use the power tool if the switch does not turn it
Water entering a power tool will increase the risk of on and off. Any power tool that cannot be controlled with
electric shock. the switch is dangerous and must be repaired.
d. Do not abuse the cord. Never use the cord for carrying, c. Disconnect the plug from the power source and/or the
pulling or unplugging the power tool. Keep cord away battery pack from the power tool before making any
from heat, oil, sharp edges or moving parts. Damaged or adjustments, changing accessories, or storing power
entangled cords increase the risk of electric shock. tools. Such preventive safety measures reduce the risk of
e. When operating a power tool outdoors, use an starting the power tool accidentally.
extension cord suitable for outdoor use. Use of a cord d. Store idle power tools out of the reach of children and
suitable for outdoor use reduces the risk of electric shock. do not allow persons unfamiliar with the power tool or
f. If operating a power tool in a damp location is these instructions to operate the power tool. Power
unavoidable, use a residual current device (RCD) tools are dangerous in the hands of untrained users.
protected supply. Use of an RCD reduces the risk of
electric shock.
3
Downloaded from www.Manualslib.com manuals search engine
e. Maintain power tools. Check for misalignment or Hold power tool by insulated gripping surfaces when
binding of moving parts, breakage of parts and any performing an operation where the cutting accessory
other condition that may affect the power tools may contact hidden wiring or its own cord. Cutting
operation. If damaged, have the power tool repaired accessory contacting a "live" wire may make exposed
before use. Many accidents are caused by poorly metal parts of the power tool "live" and shock the operator.
maintained power tools. Use clamps or another practical way to secure and
f. Keep cutting tools sharp and clean. Properly support the workpiece to a stable platform. Holding the
maintained cutting tools with sharp cutting edges are less work by hand or against your body leaves it unstable and
likely to bind and are easier to control. may lead to loss of control.
g. Use the power tool, accessories and tool bits etc., Before drilling into walls, floors or ceilings, check for the
in accordance with these instructions, taking into location of wiring and pipes.
account the working conditions and the work to be Avoid touching the tip of a drill bit just after drilling, as it
performed. Use of the power tool for operations different may be hot.
from those intended could result in a hazardous situation. This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
5. Battery tool use and care capabilities, or lack of experience and knowledge, unless
a. Recharge only with the charger specified by the they have been given supervision or instruction
manufacturer. A charger that is suitable for one type of concerning use of the appliance by a person responsible
battery pack may create a risk of fire when used with for their safety. Children should be supervised to ensure
another battery pack. that they do not play with the appliance.
b. Use power tools only with specifically designated The intended use is described in this instruction manual.
battery packs. Use of any other battery packs may create The use of any accessory or attachment or performance
a risk of injury and fire. of any operation with this tool other than those
c. When battery pack is not in use, keep it away from recommended in this instruction manual may present
other metal objects, like paper clips, coins, keys, a risk of personal injury and/or damage to property.
nails, screws, or other small metal objects, that can
make a connection from one terminal to another. Additional safety instructions for batteries and
Shorting the battery terminals together may cause burns chargers
or a fire.
d. Under abusive conditions, liquid may be ejected from Batteries
the battery; avoid contact. If contact accidentally Never attempt to open for any reason.
occurs, flush with water. If liquid contacts eyes, Do not expose the battery to water.
additionally seek medical help. Liquid ejected from the Do not expose the battery to heat.
battery may cause irritation or burns. Do not store in locations where the temperature may
exceed 40 °C.
6. Service Charge only at ambient temperatures between 10 °C and
a. Have your power tool serviced by a qualified repair 40 °C.
person using only identical replacement parts. This will Charge only using the charger provided with the tool.
ensure that the safety of the power tool is maintained. When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Additional power tool safety warnings
@
Under extreme conditions, battery leakage may occur.
When you notice liquid on the battery, proceed as follows:
Warning! Additional safety warnings for drills and - Carefully wipe the liquid off using a cloth. Avoid skin
impact drills contact.
- In case of skin or eye contact, follow the instructions
Wear ear protectors with impact drills. Exposure to below.
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of Warning! The battery fluid, a 25-30% solution of potassium
control can cause personal injury. hydroxide, can be harmful. In case of skin contact, immediately
rinse with water. Neutralise with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse abundantly with
clean water for at least 10 minutes. Consult a physician.
4
Downloaded from www.Manualslib.com manuals search engine
Electrical safety
#
Fire hazard! Avoid short-circuiting the contacts of
a detached battery (e.g. when storing the battery in
o
a toolbox). Your charger is double insulated; therefore no earth
wire is required. Always check that the mains voltage
corresponds to the voltage on the rating plate.
p
Do not incinerate the battery. Never attempt to replace the charger unit with
a regular mains plug.
Do not attempt to charge damaged batteries. If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Chargers Centre in order to avoid a hazard.
Use your Black & Decker charger only to charge the
$
Do not probe the charger. 5. Battery
6. Battery release button
:
The following pictograms are shown on the tool: Open the chuck by turning the front part (11) with one
hand while holding the rear part (12) with the other (fig. B).
Warning! To reduce the risk of injury, the user must Insert the bit shank (17) into the chuck.
read the instruction manual. Firmly tighten the chuck by turning the front part (11) with
one hand while holding the rear part (12) with the other.
5
Downloaded from www.Manualslib.com manuals search engine
Removing and refitting the chuck (fig. C) Selecting the direction of rotation
Open the chuck as far as possible. For drilling and for tightening screws, use forward (clockwise)
Remove the chuck retaining screw by turning it clockwise rotation. For loosening screws or removing a jammed drill bit,
using a screwdriver. use reverse (counterclockwise) rotation.
Tighten an Allen key (14) into the chuck and strike it with To select forward rotation, push the forward/reverse slider
after prolonged storage, it will only accept an 80% charge. the drilling position by aligning the symbol with the
After several charge and discharge cycles, the battery will marking (15).
attain full capacity. The battery may become warm while For screwdriving, set the collar to the desired setting. If you
charging; this is normal and does not indicate a problem. do not yet know the appropriate setting, proceed as follows:
- Set the collar (3) to the lowest torque setting.
Warning! Do not charge the battery at ambient temperatures - Tighten the first screw.
below 4 °C or above 40 °C. Recommended charging - If the clutch ratchets before the desired result is
temperature: approx. 24 °C. achieved, increase the collar setting and continue
tightening the screw. Repeat until you reach the correct
Charger with charging base (fig. D) setting. Use this setting for the remaining screws.
To charge the battery (5), remove it from the tool and
insert it into the charging base (8). The battery will only fit Switching on and off
into the charging base in one way. Do not force. Be sure
that the battery is fully seated in the charging base. Variable speed switch
Plug in the charger. To switch the tool on, press the variable speed switch (1).
After normal use, a charging time of 3 hours will provide The tool speed depends on how far you press the switch.
sufficient power for most applications. However, further To switch the tool off, release the variable speed switch.
6
Downloaded from www.Manualslib.com manuals search engine
Use HSS drill bits when drilling in metal. Black & Decker provides a facility for the collection and
Use masonry bits when drilling in soft masonry. recycling of Black & Decker products once they have reached
Use a lubricant when drilling metals other than cast iron the end of their working life. To take advantage of this service
and brass. please return your product to any authorised repair agent who
Make an indentation using a centre punch at the centre of will collect them on our behalf.
the hole to be drilled in order to improve accuracy.
You can check the location of your nearest authorised repair
Screwdriving agent by contacting your local Black & Decker office at the
Always use the correct type and size of screwdriver bit. address indicated in this manual. Alternatively, a list of
If screws are difficult to tighten, try applying a small authorised Black & Decker repair agents and full details of our
amount of washing liquid or soap as a lubricant. after-sales service and contacts are available on the Internet
Always hold the tool and screwdriver bit in a straight line at: www.2helpU.com
with the screw.
Batteries
h
Maintenance
Your Black & Decker tool has been designed to operate over Black & Decker batteries can be recharged many
a long period of time with a minimum of maintenance. times. At the end of their useful life, discard batteries
Continuous satisfactory operation depends upon proper tool with due care for our environment:
care and regular cleaning.
Run the battery down completely, then remove it from the
Your charger does not require any maintenance apart from tool.
regular cleaning. NiCd, NiMH and Li-Ion batteries are recyclable. Take them
to any authorised repair agent or a local recycling station.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before Technical data
cleaning it. CD12 CD112
Regularly clean the ventilation slots in your tool and Voltage VDC 12 12
charger using a soft brush or dry cloth. No-load speed min-1 700 700
Regularly clean the motor housing using a damp cloth. Max. torque Nm 8 8
Do not use any abrasive or solvent-based cleaner. Chuck capacity mm 10 10
Regularly open the chuck and tap it to remove any dust Max drilling capacity
from the interior. Steel mm 10 10
Wood mm 25 25
Protecting the environment Weight kg 0.9 0.9
Z
Separate collection. This product must not be CD14 CD18
disposed of with normal household waste. Voltage VDC 14.4 18
No-load speed min-1 750 850
Should you find one day that your Black & Decker product Max. torque Nm 12.5 13
needs replacement, or if it is of no further use to you, do not Chuck capacity mm 10 10
dispose of it with household waste. Make this product Max drilling capacity
Steel mm 10 10
z
available for separate collection.
Wood mm 25 25
Separate collection of used products and packaging Weight kg 1.01 1.03
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
7
Downloaded from www.Manualslib.com manuals search engine
KC12GT KC14GT If a Black & Decker product becomes defective due to faulty
Voltage VDC 12 14,4 materials, workmanship or lack of conformity, within 24 months
No-load speed min-1 700 750 from the date of purchase, Black & Decker guarantees to
Max. torque Nm 8 12,5 replace defective parts, repair products subjected to fair wear
Chuck capacity mm 10 10 and tear or replace such products to ensure minimum
Max drilling capacity inconvenience to the customer unless:
Steel mm 10 10 The product has been used for trade, professional or hire
Wood mm 25 25 purposes;
Weight kg 0,9 1,01 The product has been subjected to misuse or neglect;
Capacity Ah 1.0 1.2 1.2 authorised repair agents or Black & Decker service staff.
Weight kg 0.5 0.7 0.73 To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
Charger check the location of your nearest authorised repair agent by
Input voltage VAC 230 contacting your local Black & Decker office at the address
Approx. charging time h 3 indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
EC declaration of conformity service and contacts are available on the Internet at:
CD12/CD112/CD14/CD18/KC12GT/KC14GT www.2helpU.com
Black & Decker declares that these products conform to:
98/37/EC, EN 60745 Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up to
Level of sound pressure according to EN 60745: date on new products and special offers. Further information
Sound pressure (LpA) 65.8 dB(A), uncertainty (K) 3 dB(A) on the Black & Decker brand and our range of products is
Acoustic power (LWA) 76.8 dB(A), uncertainty (K) 3 dB(A) available at www.blackanddecker.co.uk
_
uncertainty (K) 1.5 m/s2
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-8-2007
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
8
Downloaded from www.Manualslib.com manuals search engine
TYP.
CD12C - CD12CA - CD12CAH - CD12CE -
CD12GTK - CD112CE - CD14C - CD18C
2
19 6
CD12CA - CD12CAH -
CD12CE - CD12GTK - 5
CD112CE 10
4
1
CD12GTK -
CD14GTK
18
17
11
8
3
14 CD12GTK -
CD14GTK
9
16
15
1
12
15
XE
13
13
E13503 www.2helpU.com 23 - 10 - 07
9
Downloaded from www.Manualslib.com manuals search engine
TYP.
KC12GT 1
5
10
17
18
4
3
11
1
19 1
8
15
14 9
16
12
12
13
20
E13908 www.2helpU.com 19 - 09 - 07
10
Downloaded from www.Manualslib.com manuals search engine
TYP.
KC14GTK 1
2 7
6
10
5
4
17
18
19
3 11
1
1
8
15
9
14
16
12
12
13
20
E14154 www.2helpU.com 19 - 09 - 07
11
Downloaded from www.Manualslib.com manuals search engine
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark, Fax 03-9727 5940
Victoria, 3138
New Zealand
Black & Decker Tel. +64 9 259 1133
5 Te Apunga Place Fax +64 9 259 1122
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker Tel. 01753 511234
210 Bath Road Fax 01753 551155
Slough, Berkshire SL1 3YD Helpline 01753 574277
90527180 10/07