Professional Documents
Culture Documents
ENCLOSURES
14
MAS 18
mild steel
IP 66; NEMA 4, 12, 13
IK 10
H: 200-1200
W: 200-800
D: 155-400
MAD 22
mild steel
IP 55; NEMA 12,13
IK 10
H: 600-1400
W: 800-1200
D: 300
MAP 24
mild steel
IP 66; NEMA 4, 12, 13
IK 10
H: 300
W: 600-1200
D: 300
ASR 28
stainless steel
IP 66; NEMA 4X,12,13
IK 10
H: 180-1400
W: 200-800
D: 150-400
Accessories
Mounting plates 34
ADR 30 Fixation 36
stainless steel
Doors 37
IP 55; NEMA 12,13
IK 10 Locks 40
H: 1000
W: 1000-1200 Rainhoods 42
D: 300
Plinths 43
Cable management 44
15
Eldon MultiMount mild steel of the equipment on the mounting plate and
holes in top and bottom have been applied for
cable fixing.
The enclosure consists of two parts: the body Furthermore the mounting plate is equipped with
and the door. The door is secured by means of side markings every 10mm for easy mounting
16
MultiMount mild steel
wall mounting enclosures
Typical applications:
heating, ventilation,
air conditioning OEMs,
small control systems,
distribution solutions.
Multi-purpose:
mounting plate,
19 inch profiles,
swing frame,
modular system.
Easy-to-work-with.
Factory customisation.
17
CATALOGUE 2011.book Page 18 Monday, July 11, 2011 2:29 PM
IP 66/NEMA 4, 12, 13
Technical data IK 10
Material: Body: 1.2mm mild steel / 1.4mm MAS0606021R5 and Mounting plate: The mounting plate is marked vertically at
above / 1.5mm MAS1008026R5 and above, and 400mm depth 10mm intervals for easy horizontal positioning of equipment. On
enclosures. Gland plate: 1.4mm mild steel. Door: 1.2mm mild the top and bottom there are holes to facilitate cable fixing. Fixed
steel / 1.4mm MAS0606021R5 and above / 1.8mm onto M8 press welded studs to the rear of the enclosure. All sides
MAS1006026R5 and above. Mounting plate: 2mm galvanized from 800mm and above are strengthened by folded edges. By
steel. using the AMG accessory the mounting plate position can be
Body: Folded and seam welded. Four 8.5mm diameter holes for adjusted to any depth.
wall fixing, pressed out in 20.4mm diameter x 2mm depressions Gland Plate Opening: Situated at the far rear of the enclosure to
to allow air circulation around the rear part of the enclosure. make cabling onto the mounting plate easier.
Door: Surface mounted with 130 opening. Concealed Protection: Complies with IP 66, and NEMA 4, 12 and 13. For
removable hinges with captive pin. Hinges can be mounted to outdoor installation the use of rain hood ARF is recommended,
allow left or right hand opening. From height 300mm and above and the corrosion resistance must be taken into consideration.
there are studs to mount door profiles MMDP, and from height Finish: RAL 7035 structure powder coating.
600 and above the profiles are included as standard. Sealing is Delivery: Enclosure with door, and two door mounting profiles
ensured by an injected one piece polyurethane gasket. from size MAS0604015R5 and above. Gland plate(s) with
Lock: Customised lock with double grip for easy opening of the gasket(s), plastic double-bit 3mm key, and mounting accessories.
door. Double-bit 3mm insert and 90 movement. 1000mm high Earthing facilities.
enclosures and above have espagnolette three point locking.
Other inserts are available as an accessory.
Product specifications, CAD drawings and information available on the website Wall Mounting 19
Chapter_01_WALL_MOUNTING__2011_61898_0.fm Page 20 Thursday, July 28, 2011 10:55 AM
Product specifications, CAD drawings and information available on the website Wall Mounting 21
Chapter_01_WALL_MOUNTING__2011_61898_0.fm Page 22 Thursday, July 28, 2011 12:50 PM
IP 55 / NEMA 12,13
Technical data IK 10
Material: Body: 1.4mm mild steel MAD0608030R5 / 1.5mm On the top and bottom there are holes to facilitate cable fixing.
MAD0801230R5 and above. Gland plate: 1.4mm mild steel. Fixed onto M8 press welded studs to the rear of the enclosure. All
Doors: 1.4mm mild steel / 1.8mm MAD0801230R5 and above. sides from 800mm and above are strengthened by folded edges.
Mounting plate: 2mm galvanized steel / 2.5mm MAD1001030R5 By using the AMG accessory the mounting plate position can be
and above. adjusted to any depth.
Body: Folded and seam welded. Four 8.5mm diameter holes for Gland Plate Opening: Situated at the far rear of the enclosure to
wall fixing, pressed out in 20.4mm diameter x 2mm depressions make cabling onto the mounting plate easier.
to allow air circulation around the rear part of the enclosure. Protection: Complies with IP 55, and NEMA 12, 13. For outdoor
Door: Surface mounted with 130 opening. Concealed installation the use of rain hood ARF is recommended, and the
removable hinges with captive pin. Two removable mounting corrosion resistance must be taken in consideration.
profiles in the right hand door. Sealing is ensured by an extruded Finish: RAL 7035 structure powder coating.
one piece polyurethane gasket. Delivery: Enclosure with doors, and two door mounting profiles
Lock: Customised lock with double grip for easy opening of the on the right door. Gland plate(s) with gasket(s), plastic DIN 3mm
door, double-bit 3mm insert and 90 movement. Espagnolette key, and mounting accessories. Earthing facilities.
three point locking. Other inserts are available as an accessory.
Mounting plate: The mounting plate is marked vertically at
10mm intervals for easy horizontal positioning of equipment.
Dimensions
Product specifications, CAD drawings and information available on the website Wall Mounting 23
Chapter_01_WALL_MOUNTING__2011_61898_0.fm Page 24 Tuesday, August 2, 2011 4:21 PM
The MAP is an incredibly versatile enclosure, for use in either stand alone applications, or in conjunction with MAS/MAD as a
cableway.
IP 66 / NEMA 4, 12, 13
Technical data IK 10
Material: Body: 1.4mm mild steel. Panel: 1.4mm mild steel. All sides from 800mm and above are strengthened by folded
Mounting plate: 2mm galvanized steel. edges. By using the AMG accessory the mounting plate position
Body: Folded and seam welded. Four 8.5mm diameter holes for can be adjusted to any depth.
wall fixing pressed out in 20.4mm diameter x 2mm depressions to Gland Plate Opening: In top and bottom. Situated at the far rear
allow air circulation around the rear part of the enclosure. of the enclosure to make cabling onto the mounting plate easier.
Front panel: Surface mounted with 90 opening. Concealed Gland plates (AF) and gaskets (AG) are not included. The gland
removable hinges with captive pin. Hinges can be mounted to plates used are those delivered with the MAS or MAD enclosures.
allow top or bottom opening. Mechanical door stop keeps panel Protection: Mounted stand alone complies with IP 66, and
open. One removable mounting profile on the hinge side. Sealing NEMA 4, 12 and 13, as long as you mount the gland plate(s) and
is ensured by an extruded one piece polyurethane gasket. gasket(s), supplied as an accessory. Combined with MAS or
Lock: Customised lock with double grip for easy opening of the MAD complies with IP 55 and NEMA 12. For outdoor installation
panel. double-bit 3mm insert and 90 movement. Other inserts the use of rain hood ARF is recommended, and the corrosion
are available as an accessory. resistance must be taken in consideration.
Mounting plate: The mounting plate is marked vertically at Finish: RAL 7035 structure powder coating.
10mm intervals for easy horizontal positioning of equipment. On Delivery: Enclosure with panel, and one panel mounting profile.
the top and bottom there are holes to facilitate cable fixing. Fixed Plastic double-bit 3mm key, and mounting accessories. Earthing
onto M8 press welded studs to the rear of the enclosure. facilities.
Dimensions
Product specifications, CAD drawings and information available on the website Wall Mounting 25
Eldon MultiMount in the enclosure:
either against the rear wall of the enclosure
or using a mounting kit, which is adjustable
Technical Information The enclosure consists of two parts: the base To comply with EMC guidelines, the mounting
and the door. The door is secured by means of plate is manufactured from Sendzimir zinc-plated
two or three stainless steel hinges and its angle steel plate 2-2.5mm thick. This plate provides
of opening is at least 130. The hinges are not an equipotential mass connection between all
Sturdy cruciform body folded from cold pressed visible in closed position and are fitted with a devices in the enclosure.
1/1.5mm pre-grained AISI 304 / AISI 316L captive hinge pin. The opening direction of the
stainless steel. The enclosure edge is folded in door is left-right and is reversible. The enclosure offers maximum protection to
the shape of a channel to avoid water stagnating the user and equipment by a protection degree
on the seal. The single doors are closed by one, two or three IP66 -IK 10 as per lEC 60529 and NBN G20-001
point locking system, the double doors by means (IP55 - IK 10 for enclosures with double door
The door is made out 1.5/2mm pre-grained AISI of three point espagnolette system. The door also and enclosures with glazed door). When using an
304 / AISI 316L stainless steel with M6 studs has a seamless polyurethane gasket. interior door or modular framework or 19 swing
allowing mounting of MMDP profiles (accessory) frame, protection degree IP 20 is guaranteed
for easy installation of cable tracks, profiles, etc. The chrome plated Eldon customized 3mm within the enclosure. Complying with NEMA
Body and door are provided with M8 threaded double-bit lock with 90-degree movement can 4x, 12 and 13.
studs for earthing connection. be interchanged with other inserts.
Possibility for integrated sloping and overhanging
The enclosure has external a pre-grained finish, The door opens within the outer dimensions of roof is one of the standard options especially
which gives the product an aesthetically and the enclosure body allowing enclosures to be designed for harsh environments.
highly professional appearance. mounted directly next to each other without the
door interference. The enclosures have the UL approval, as per
Finish of the outer door and body 240s pre UL standard 508 and also comply with the CSA
grained (average 0.5 microns), which makes it The mounting plate can be set up and wired certification mark, as per C22.2 no. 94.
highly suitable for the food industries (HACCP). outside the enclosure. It is placed subsequently
26
MultiMount stainless steel
wall mounting enclosures
Multi-purpose:
mounting plate,
19 inch profiles,
swing frame.
27
Chapter_01_WALL_MOUNTING__2011_61898_0.fm Page 28 Tuesday, August 2, 2011 5:37 PM
The Eldon ASR range, designed with cleanliness and ingress protection in mind, provides high resistance to corrosion and
ensures performance of equipment. Intended for harsh environments, the ASR range is the ideal solution for food and
chemical industries, pharmaceutical plants, outdoor applications and marine environments.
IP 66/NEMA 4X,12,13
IK10
Technical data
Material: AISI 304 / AISI 316L pre-grained stainless steel In enclosures with height or width of 800mm or more, the
Body: 1.0mm/ 1.5mm ASR0406021 and larger mounting plate has a fold to all four sides for extra rigidity. By
Door: 1.5mm/ 2mm ASR 1008030 and larger using the AMG accessory the mounting plate can be adjusted in
Mounting plate: 2.0mm galvanized steel. depth.
Frame: Monoblock body, folded and seam welded. Cable access: No gland plate openings as standard to maximise
Door: Corner formed in one piece. Surface mounted with 130 sealing and clean lines.
opening. Concealed AISI 304 stainless steel hinges with Protection: Corresponds with IP 66 and NEMA 4X, 12 and 13, IK
removable pin. Can be mounted to give left or right hand opening. 10.
Sealing is ensured by an injected one piece polyurethane gasket. Finish: 240s pre grained stainless steel (average 0.5 micron).
Inside of door fitted with four welded studs for equipment profiles. Delivery: Mounting plate, complete with fitting accessories and
Lock: Eldon customized chrome plated double-bit 3mm lock with earthing facilities. Packaged in a reusable carton.
90 movement and anti-vibration mechanism. 1000mm high Additional information: The use of Thermal Management
enclosures and above have espagnolette three point locking. Equipment, venting and rainhoods is advised for harsh and
Stainless steel lock and other versions are available as outdoor applications. Please see our general accessories section
accessories. and Technical chapter for additional information.
Mounting plate: Fixed onto M8 studs welded to the rear of the
enclosure.
Dimensions
Product specifications, CAD drawings and information available on the website Wall Mounting 29
Chapter_01_WALL_MOUNTING__2011_61898_0.fm Page 30 Thursday, July 14, 2011 3:29 PM
IP 55/NEMA 12, 13
Technical data IK10
Material: AISI 304 / AISI 316L pre-grained stainless Mounting plate: Fixed onto M8 studs welded to the rear of the
Body: 1.5mm. Door: 2,0mm. enclosure. In enclosures with height or width of 800mm or more,
Mounting plate: 2.5mm galvanized steel. the mounting plate has a fold to all four sides for extra rigidity. By
Body: Monoblock body, folded and seam welded. using the AMG accessory the mounting plate can be adjusted in
Door: Corner formed in one piece. Surface mounted with 130 depth.
opening. Concealed AISI 304 stainless steel hinges with Finish: 240s pre grained stainless steel (average 0.5 micron).
removable pin. Inside of door carries four welded studs for Protection: Corresponds with IP55 and NEMA 12,13, IK10.
equipment profiles. Sealing is ensured by an injected one piece Delivery: Mounting plate, complete with fitting accessories and
polyurethane gasket. earthing facilities. Packaged in a reusable carton.
Lock: Eldon customized chrome plated double-bit 3mm lock with Additional information: The use of Thermal Management
90 movement and anti-vibration mechanism. Espagnolette three Equipment, venting and rainhoods is advised for harsh and
points locking. Stainless steel lock and other versions are outdoor applications Please see our general accessories section
available as accessories. and Technical chapter for additional information.
Dimensions
50
Product specifications, CAD drawings and information available on the website Wall Mounting 31
CATALOGUE 2011.book Page 32 Monday, July 11, 2011 2:29 PM
IP 66/NEMA4x ,12,13
Technical data IK 10
Material: AISI 304 pre-grained stainless steel/AISI 316L (on Mounting plate: Fixed onto M8 studs welded to the rear of the
request). enclosure. In enclosures with height or width of 800 mm or more,
Body: 1.5mm, Door: 1.5mm/2 mm on AFS 10083 and larger. the mounting plate has a fold to all four sides for extra rigidity. By
Mounting plate: 2.0mm galvanized steel. using the AMG accessory the mounting plate can be adjusted in
Body: The top of the body is equipped with a sloping roof at an depth.
angle of between 8 and 20 degrees sloping towards the front, Cable access: No gland openings as standard to maximise the
giving a 10 mm overhang to remove any liquids away from the sealing and clean lines according to the HACCP.
door. Folded and seam welded. Protection: Corresponds with IP 66 and NEMA 4X, 12, 13, IK10
Door: Corner formed in one piece. Surface mounted with 130 Finish: 240s pre grained stainless steel (average 0.5 micron).
opening. Concealed AISI 304 stainless steel hinges with Delivery: Mounting plate, complete with fitting accessories and
removable pin. Can be mounted to give left or right hand opening earthing facilities. Packaged in a re-usable carton.
(Machining is required). Sealing is ensured by an injected one Additional information: The use of Thermal Management
piece polyurethane gasket. Inside of door fitted with four welded Equipment, and venting should be utilised for harsh and outdoor
studs for equipment profiles. applications Please see our general accessories section and
Lock: Chrome plated double-bit 3mm lock with 90 movement. Technical chapter for additional information.
Stainless steel lock and other locks available on request.
Dimensions
W DD+10 W-50
148
DD-20
=
50
H
H
HH-25
=
148
76.5
85
W-100
DD
50 50
W-62.5
Product specifications, CAD drawings and information available on the website Wall Mounting 33
CATALOGUE 2011.book Page 34 Monday, July 11, 2011 2:29 PM
Description: Steel mounting plate for MultiMount enclosure. Description: Insulated mounting plate for MultiMount
All sides from 800 mm and above are strengthened by folded enclosures. By using the AMG accessory, the mounting plate
edges. By using the AMG accessory, the mounting plate position can be adjusted to any depth.
position can be adjusted to any depth. Material: Bakelite
Material: Galvanized steel. Pack quantity: 1 piece.
Pack quantity: 1 piece.
Enclosure dimension Mounting plate dimension Enclosure dimension Mounting plate dimension
H W h w Part No. H W h w Part No.
200 200 170 150 AMP02020 200 200 170 150 AMI02020
250 200 220 150 AMP02520 250 200 220 150 AMI02520
250 220 200 AMP02525 250 220 200 AMI02525
300 250 270 200 AMP03025 300 250 270 200 AMI03025
300 270 250 AMP03030 300 270 250 AMI03030
600 270 550 AMP03060 350 250 320 200 AMI03525
800 270 750 AMP03080 400 300 370 250 AMI04030
1000 270 950 AMP03100 400 370 350 AMI04040
1200 270 1150 AMP03120 500 370 450 AMI04050
350 250 320 200 AMP03525 600 370 550 AMI04060
400 300 370 250 AMP04030 500 300 470 250 AMI05030
400 370 350 AMP04040 400 470 350 AMI05040
500 370 450 AMP04050 500 470 450 AMI05050
600 370 550 AMP04060 600 400 570 350 AMI06040
500 300 470 250 AMP05030 500 570 450 AMI06050
400 470 350 AMP05040 600 570 550 AMI06060
500 470 450 AMP05050 800 570 750 AMI06080
600 400 570 350 AMP06040 700 500 670 450 AMI07050
500 570 450 AMP06050 800 400 770 350 AMI08040
600 570 550 AMP06060 600 770 550 AMI08060
800 570 750 AMP06080 800 770 750 AMI08080
700 500 670 450 AMP07050 1000 600 970 550 AMI10060
800 400 770 350 AMP08040 800 970 750 AMI10080
600 770 550 AMP08060 1200 600 1170 550 AMI12060
800 770 750 AMP08080 800 1170 750 AMI12080
1200 770 1150 AMP08120
1000 600 970 550 AMP10060
800 970 750 AMP10080
1000 970 950 AMP10100
1200 600 1170 550 AMP12060
800 1170 750 AMP12080
1000 1170 950 AMP12100
1400 1000 1370 950 AMP14100
Description: It simplifies installation and equipment mounting. Description: To provide depth adjustment for different
Rectangular holes 26 x 11mm to obtain required fixing accessories: mounting plate, 19" profiles and inner door. In
positions with snap nuts. The nuts can be moved around within stainless steel enclosure machining is required.
the rectangular hole. By using the AMG accessory, the Material: 2mm galvanized steel.
mounting plate position can be adjusted to any depth. Depth adjustment: Distance to the door D-35 to 65mm.
Material: Galvanized steel. Pack quantity: 2 pairs with mounting accessories.
Pack quantity: 1 piece.
Product specifications, CAD drawings and information available on the website Wall Mounting 35
CATALOGUE 2011.book Page 36 Monday, July 11, 2011 2:29 PM
MMH, Hinges
.
Description: To replace the standard door, it provides a clear Description: To replace the standard door, provides a clear
view of the components installed inside the enclosure. Allows view of the components installed inside the enclosure.
all the options of the locking program. Allows all the options of the locking program.
Material: 1.2mm mild steel / 1.4mm ADC06060R5 and above / Material: 1.5mm AISI 304 stainless steel, 2mm ASR 1008030
1.8mm ADC10060R5 and above, and 4mm clear safety glass. and above, and 4mm clear safety glass.
Finish: RAL 7035 structure powder coating. Finish: 240s pre-grained stainless steel (average 0.5 micron)
Protection: Complies with IP 55 and NEMA 12,13 Protection: Complies with IP 55 and NEMA 12, 13.
Pack quantity: 1 door. Pack quantity: 1 door
Product specifications, CAD drawings and information available on the website Wall Mounting 37
CATALOGUE 2011.book Page 38 Monday, July 11, 2011 2:29 PM
Product specifications, CAD drawings and information available on the website Wall Mounting 39
CATALOGUE 2011.book Page 40 Monday, July 11, 2011 2:29 PM
ALT, Handles
Description: To strengthen the door, mounted on the inside of .
the door on the M6 welded studs. equipped with 10mm hole
pattern.
Material: 1.4mm galvanized steel.
Dimension: 15 x 14mm.
Pack quantity: 1 pair with mounting accessories.
For enclosure
H Part No.
500 MMDP050
600 MMDP060 Description: Alternative handles to replace the standard lock.
700 MMDP070 Pack quantity: 1 piece.
800 MMDP080
1000 MMDP100
1200 MMDP120
1400 MMDP140
Description Part No.
Plastic handle ALT560
Plastic handle with cylinder lock, ALT563
Key 5333
Chrome plated T-handle with cylinder lock, key ALT561
C21323
Chrome plated handle with cylinder lock, key ALT562
C21323
Description: Key with Eldon logo. Easy to use design and Description: Multi-Key function with Eldon logo and a different
provides a good grip. key in every end: double-bit 5mm, square 8mm, triangle 8mm
Material: Die cast alloy and a standard hexagonal adaptor to use with the screw ends.
Pack quantity: 1 piece Material: Steel.
Pack quantity: 1 piece.
ALI, Inserts
.
Product specifications, CAD drawings and information available on the website Wall Mounting 41
CATALOGUE 2011.book Page 42 Monday, July 11, 2011 2:29 PM
Fan Cover
H W D Suitable for Part No. Part No.
fans AISI 304 AISI 316L
144 134 100 EF100 / EF200 EFCS20 EFCS20-316*
Description: M12 thread. Complies with DIN580 lifting 275 265 100 EF250 / EF300 EFCS25-30 EFCS25-30-316*
requirements. Machining is required. 353 343 100 EF500 / EF700 EFCS50-60 EFCS50-60-316*
Material: Steel. *Delivery times upon request
Pack quantity: 2 eye-bolts, 2 reinforcements and mounting
accessories.
Part No.
AL9301
Description: Four corner pieces with removable front covers. Description: Four U-section side pieces fixed by screws to the
The side panels PA must be ordered separately. Available corner sections. (Machining is required)
heights: 100 and 200mm. Machining is required. Material: 2 mm AISI 304/AISI 316L pre-grained stainless steel
Material: 2.5mm mild steel for corner pieces, and 1.5mm mild Finish: 240s pre-grained (0,5 microns average).
steel for covers. Pack quantity: 1 plinth with mounting material
Finish: RAL 7022 structure powder coating.
Pack quantity: 4 corner pieces and 2 front covers, with
mounting accessories.
H W D Part No. Part No.
AISI 304 AISI 316L
100 600 300 MSVS1063 MSVS1063-316*
800 300 MSVS1083 MSVS1083-316*
H W Part No. 400 MSVS1084 MSVS1084-316*
100 400 P1040 1000 300 MSVS1103 MSVS1103-316*
500 P1050 1200 300 MSVS1123 MSVS1123-316*
600 P1060 *Delivery times upon request
800 P1080
1000 P1100
1200 P1120
200 400 P2040
PFF, Floor stands
500 P2050 .
600 P2060
800 P2080
1000 P2100
1200 P2120
Product specifications, CAD drawings and information available on the website Wall Mounting 43
CATALOGUE 2011.book Page 44 Monday, July 11, 2011 2:29 PM
Description: Gland plate for the standard gland opening. Description: Louvered plate, pressed out 5 mm.
Material: 1.4mm mild steel. Material: 1.4mm mild steel.
Finish: RAL 7035 structure powder coating.
Finish: RAL 7035 structure powder coating. Protection: Complies with IP 23, in bottom or vertical position
Pack quantity: 1 piece. Pack quantity: 1 piece.
Size For opening Part No. Size For opening Part No.
0S 110 x 56 AF00SR5 1 210 x 96 AFR01R5
1S 210 x 56 AF01SR5 2 310 x 96 AFR02R5
2S 310 x 56 AF02SR5 3 410 x 96 AFR03R5
3S 410 x 56 AF03SR5 4 510 x 96 AFR04R5
1 210 x 96 AF01R5
2 310 x 96 AF02R5
3 410 x 96 AF03R5
AFG, Ventilated gland plate with fly-net
4 510 x 96 AF04R5 .
Product specifications, CAD drawings and information available on the website Wall Mounting 45
Chapter_01_WALL_MOUNTING__2011_61898_1.fm Page 46 Monday, July 11, 2011 2:51 PM
Product specifications, CAD drawings and information available on the website Wall Mounting 47
CATALOGUE 2011.book Page 48 Monday, July 11, 2011 2:29 PM
Product specifications, CAD drawings and information available on the website Wall Mounting 49
Chapter_01_WALL_MOUNTING__2011_61898_1.fm Page 50 Thursday, July 21, 2011 11:01 AM
Description: Support kit for the mounting of the modular Description: Front panel for modules. Provided with one DIN
panels and components by steps of 150mm. A space for rail (PP 1535) per row for MCB (Mini Circuit Bracker).
equipment of 46mm high is provided. Independent of the depth Material: 1.2mm steel plate.
of the enclosure, the system can be used in combination with Finish: Structure powder paint, RAL 7035.
glazed door and a mounting plate is still usable. 50mm of Pack quantity: 1 piece with mounting material.
space is provided for the equipment between the door and the
panels. In order to allow easy installation of the equipment and
the wiring, the system can be assembled, fully equipped and
pre-wired outside the enclosure, and then fitted into the H W N of N of Part No.
module rows
enclosure. Cut-outs are provided on the sides of the vertical
150 600 24/1 1 MCP1506R5
profiles for cable routing. The kit contains two vertical profiles, 800 35/1 1 MCP1508R5
top and bottom blanking plates and fixing material. 200 600 24/1 1 MCP2006R5
Material: 1.35mm steel plate. Structure powder paint, RAL 800 35/1 1 MCP2008R5
7035. 300 600 48/2 2 MCP3006R5
Pack quantity: 1 kit with fitting material. 800 70/2 2 MCP3008R5
450 600 72/3 3 MCP4506R5
800 105/3 3 MCP4508R5
600 600 96/4 4 MCP6006R5
800 140/4 4 MCP6008R5
Description: Front panel with cut outs for control meters and
network analyser. To be mounted in a CMV profile for MultiFlex
or in an ACM for a MultiMount enclosure.
Material: 1.2mm steel plate.
Finish: Structure powder paint, RAL 7035.
Pack quantity: 1 piece with mounting material.
Description: Front blank panel to cover unused space or to Description: Allowing fixing MCCBs of any manufacturer
mount special equipment. Panels are with flanged top and (machining is required). Requires MD depth adjustment kit.
bottom to provide extra stiffness. Material: 2mm galvanized steel plate.
Material: 1.2mm steel plate. Pack quantity: 1 piece.
Finish: Structure powder paint, RAL 7035.
Pack quantity: 1 piece with mounting material.
Part No.
MD4
Product specifications, CAD drawings and information available on the website Wall Mounting 51