Professional Documents
Culture Documents
Bijeesh P
Associate Professor
Saintgits College of Engineering, Kerala, India
Abstract
Most of the heat energy released from the fuel of an internal combustion engine is wasted to the environment. This is a serious
issue in this world of depleting fuels. So an effort is made to recover the heat wasted from the exhaust gas of an internal
combustion engine. If the heat wasted out through the exhaust gas is utilised, we can improve the efficiency of the engine to
some extent. There are a lot of research works in the field of waste heat recovery systems. Many succeeded in their own
methodologies. We hereby attempt to recover the waste heat from the exhaust gas and use the heat energy recovered to improve
the efficiency of the internal combustion engine. For the same we studied the exhaust gas temperature of a four stroke diesel
engine at various RPM. The exhaust gas temperature at 4000 RPM has got the maximum temperature. So a recovery system for a
constant RPM of 4000 is designed. The recovery system consists of a shell and tube heat exchanger and a uniflow steam engine
which is coupled to the main engine. The coupled steam engine improves the efficiency of the main engine by lowering the
frictional power at the power stroke and idle stroke of the main engine. The initial cost of the system is high due to the additional
recovery system. But in the long run the system proves to be profitable.
Keywords: IC Engine, Exhaust Gas, Efficiency
_______________________________________________________________________________________________________
I. INTRODUCTION
In this age of globalization there is a decreasing availability of fossil fuels. So there is a need of conserving it for the future
generations. In normal IC engines, a major part of fuel energy is wasted through exhaust gas, cooling water and other losses. We
know that a normal IC engine is only 30 to 40 %. This means that the rest of the 70 to 60 % of the heat is lost as waste to the
environment. But we know from the basic law of thermodynamics we cannot tap 100% of the available energy. But if we
synthesis a method to tap the lost heat from the sink and formulate a method to increase the efficiency of the IC engine, it would
be worth for the future generation.
We could tap this lost heat by many ways and utilized it for many purposes. In this project we used a heat exchanger to tap the
heat. This heat is further used to increase the efficiency of the engine with the help of a steam. The steam engine cylinder used is
considered as an extra cylinder which working together with the other cylinders of the engine whose efficiency is to be
increased. The steam engine used gives additional power to the whole system. This additional power decreases the frictional
power of the system thereby increasing the efficiency of the IC engine.
II. METHODOLOGY
The heat energy released to the exhaust gas in engines of various cubic capacities is analyzed.
Engine suitable for this system is selected.
The amount of heat in exhaust gas is calculated.
Suitable heat exchanger type is selected.
Numerical designing of heat exchanger is done.
The different parts of the heat exchanger are modeled using CATIA.
The volume of steam chamber required is calculated.
The power developed from the steam chamber is calculated.
The software analysis of the heat exchanger and the steam chamber are done using ANSYS.
A. Engine Selection:
Field analysis and literature study on different engines of various cubic capacity from 150cc to 1500cc were conducted. We
studied the temperature of exhaust gas from these engines and found that the temperature is too low for low capacity engines.
C in engines of higher capacities. Also, the mass flow rate of the exhaust is higher
in large engines. Finally we selected 1573cc diesel engine.
Engine specification:
Engine type : inline 4 cylinder
Bore : 75mm
Stroke : 89mm
Displacement : 1573cc
Compression ratio : 18
Rated power : 80bhp@4000rpm
We also checked the exhaust gas temperature from the engine when it is working under various rpm, i.e. from 1000rpm to
4000 rpm. Here we also found that the temperature is high when the engine speed is 4000 rpm.
Table-1: Exhaust Gas Properties at Various Engine Speeds
ITEM CONTENT
Engine Speed(rpm) 1000 2000 3000 4000
Engine Power (kW) 14.9 50.2 70.8 84.8
Exhaust temperature(K) 801.5 862.4 890.8 900.5
Exhaust mass flow rate(g/s) 18.7 59.6 83.3 108
This is the maximum heat that can be transferred from exhaust gas to the cooling fluid.
D. Design Considerations:
The working is fed to the heat exchanger at a pressure of 10bar and the heat exchanger designed should provide steam at the
outlet of shell with pressure drops within allowable limit. The exhaust gas is fed to the tube at a pressure of 5bar. Designing of
the heat exchanger is usually done on the basis of certain assumptions.
There is no heat transfer between the fluid streams and the outside environment. There are no leakages from the fluid streams to
each other or to the environment. No heat is generated or lost via chemical or nuclear reactions, mechanical work or other means.
There is no heat conduction along the length of the heat transfer surface, only in the direction of the normal of the surface. Fluid
flow rates are equally distributed throughout the whole cross-sectional areas of flow. Where temperature distribution transverse
to the flow direction is relevant, any fluid flow can be considered either completely mixed or completely unmixed. Properties of
fluids are constant inside the heat exchanger. Overall heat transfer coefficient is a constant at all locations of the heat exchanger.
Initial assumption that overall heat transfer coefficient U = 150 W/m2. Negligible fouling resistance occur in the heat exchanger
E. Designing Procedure:
The process of sizing a heat exchanger will inevitably be an iterative one. To calculate the area one has to have at least an
estimate of U, once an area is calculated on the basis of the estimate (or guess), the geometry of the heat exchanger will be
known so that a better estimate of U can be calculated, leading to a better estimate of the area, therefore some change in
geometry, requiring a new value of U to be calculated, and so on.
Processes taking place in heat exchanger:
Heating working fluid from 30 to 179.9
Vaporization of the working fluid at 179.9
Superheating of the working fluid to 205 .
Since these stages occur
-
Calculation of mass flow rate of working fluid:
We know the maximum heat transferred from the working fluid. We also know the processes happening to the working fluid. So
the flow rate of working fluid can be calculated by the following steps.
To increase temp of WF
Q1 = wf cpwf T
= wf 4.18 (179.9 30)
= 626.528 wf
To vaporize
Q2 = wf hfg
= 2013.6 wf
To superheat
Q3 = wf cpwf T
= wf 2.085(205-179.9)
= 52.335 wf
Qmax = Q1 + Q2 + Q3
90.481= wf (626.582+2013.6+52.335)
= wf 2692.5155
wf = 0.03360kg/sec
1) - NTU Method:
The -NTU method of heat exchanger analysis is based on three dimensionless parameters: the heat exchanger effectiveness ,
ratio of heat capacity rates of the fluid streams CR, and number of transfer units NTU. is a function of heat duty and/or outlet
temperatures and NTU a function of heat transfer area. Functions correlating the three dimensionless parameters to each other
exist for a variety of flow arrangements. Use of the -NTU method starts by solving two of the dimensionless parameters from
what is known about the situation, and then using the correct -NTU relationship to find the third. From that value and definition
of the third dimensionless parameter one then solves what needs to be determined: for example the required heat transfer area
from NTU in a sizing problem, or fluid outlet temperatures from in a rating problem.
Find out the mass flow rate of working
Finding out the temperature of exhaust gas after each phase
Finding out the value of heat capacity ratio R;
Based on the value of R from standard graph between - NTU, take values of NTU for maximum effectiveness.
Take estimated value of U for shell and tube heat exchanger for doing initial iteration
Calculate the area required
Fix standard tube and shell diameters
Find out the number of tubes required
Fix the number of tubes as specified by s standards
Assume single pass and find out the velocity and Reynolds number for exhaust flow
Table-2: Heat Exchanger Design Specifications
PROPERTY VALUE
Effectiveness 76.3
Total heat exchange area 18.27m2
Tube pitch 1 inch square pitch
Tube inner diameter 12.2mm
Tube outer diameter 19.1mm
Shell inner diameter 438.15mm
No of tubes 150
No of passes 6
No of baffles 11
Parts of the heat exchanger is designed and made using CATIA. The major parts of heat exchanger are:
Tube
Shell
Front end head
Rear end head
Tube Plate
From the above analysis done in ANSYS R15.0, we could understand that the maximum stress on the parts is much lesser than
the yield strength of the material made. Hence the design is safe.
The factor safety of shell cover = = 17.98
The factor safety of shell = = 8.84
The factor of safety of the tube = = 4.79
From the above analysis we could clearly understand that the design safe with a very high factor of safety.
=
= 0.014188 m3/sec
Bore of steam chamber = 2
= *2
= 0.055211 m
= 55.2 mm
C. Cam Design:
The cam profile is designed such that the cut off of the working fluid is at 50%. The lift of the valve is 4.5mm which is
5
45.
This is the required cam profile that is used to produce the required displacement of the valve.
Where,
S = suction stroke
C = compression stroke
P = power stroke
E = exhaust stroke
VII. CONCLUSION
This is a novel mechanism which improves the performance of the engine. The power of the engine increases from 80 kW at
4000 RPM to 81.91895 kW. The thermal efficiency increases from 37.3% to 38.19%.There is a decrease in the bsfc by 5.28
g/kWhr. The initial cost of the recovery mechanism is very high. But this becomes economic in long run. The analysis is carried
out theoreticallybut there may be differences when it is experimentally analyzed. The low value of the recovered heat is due to
the small engine that we took. The improvement in the performance of the engine is due to the fact that the power developed by
the mechanism is utilized to decrease part of the frictional power of the engine.
ACKNOWLEDGEMENT
The authors would like to acknowledge the support of Mechanical Engineering Department of Saintgits College of Engineering
for conducting the present investigation
REFERENCES
[1] Jianqin Fu, Jingping Liu, Yanping Yang, Chengqin Ren, Guohui Zhu- A ,
Applied Energy, 2013, pp.150-159.
[2] J.S. Jadhao, D.G. Thombare- R I , Applied Energy, 2013.
[3] Kiran K. KattaMyoungjin Kim- E - , Applied Energy, 2007.
[4] Q.A Kern P
[5] C P Kothandaraman, S Subramanyan H