Professional Documents
Culture Documents
bracket. Gear shifting operation Mounting the shifting lever Chain length Smallest
sprocket
Largest
chainring
In addition, if pedaling performance does not feel normal, check this once more.
Check that there is no looseness in any joints or connections before riding the bicycle. (BB-FC, FC-PD) < GS > < SS >
< SL-TX50-L >
Do not wash the bottom bracket with high-pressure jets of water. Use a handlebar grip Add 2 links (with the chain on both Chain
If you feel any looseness in the bottom bracket axle, the bottom bracket should be replaced. To shift from a small chainring to a larger chainring Smallest Largest FD-C051 / C050
with a maximum outer the largest sprocket and the largest sprocket chainring
If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts. When lever is pressed once, there is a shift of one step from diameter of 32 mm. chainring)
If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur. a small chainring to a larger chainring.
You should periodically wash the chainrings in a neutral detergent and then lubricate them again. In addition, cleaning the Largest Largest
Chain
chain with neutral detergent and lubricating it can be a effective way of extending the useful life of the chainrings and the Example: sprocket chainring
Guide pulley 5. Adjustment of the intermediate chainring (SL-TX50-L)
chain. from intermediate
Tension pulley 90
If the chain keeps coming off the chainrings during use, replace the chainrings and the chain. chainring to largest Set the chain onto the largest sprocket, and at the front, move the chain from
Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides. chainring. Right angle to the ground the largest chainring to the intermediate chainring. Adjust using the cable
Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way. adjusting bolt so that the clearance between the chain guide inner plate and
Chain
Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly. the chain is 0 - 0.5 mm.
Tightening torque:
Operation of the levers related to gear shifting should be made only when the front chainwheel is turning. 2.5 Nm {22 in. lbs.}
For smooth operation, use the specified outer casing and bottom bracket cable guide. Chain position
To ensure the best performance, be sure to use only the specified type of chain. The wide type chain cannot be used. To shift from a large chainring to a smaller chainring
For maximum performance we highly recommend Shimano lubricants and maintenance products. When lever is pressed once, there is a shift of one step from
Adjustment Largest
sprocket
Intermediate
chainring
Parts are not guaranteed against natural wear or deterioration resulting from normal use. a large chainring to a smaller chainring. Be sure to follow the sequence described below.
For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional
bicycle dealer. 1. Low adjustment
Example: Outer casing
Chain guide
inner plate
from largest chainring to < FD-C051 / FD-C050 / FD-TY30 / FD-TY10 > adjustment barrel
intermediate chainring.
First remove the Pro-Set alignment block. Next, Chain
set so that the clearance between the chain guide FD-C051 / C050
inner plate and the chain is 0 - 0.5 mm.
Install the shifting lever in a position where it will not If shifting is difficult from the
Loosen the top adjustment screw
intermediate chainring to the largest
obstruct brake operation and gear shifting operation. Chain guide inner counterclockwise (about 1/8 turn).
Technical Service Instructions SI-6DK0B Pedaling becomes lighter Do not use in a combination which causes brake plate chainring
operation to be obstructed. If shifting is difficult from the
Chain Loosen the low adjustment screw
intermediate chainring to the
counterclockwise (about 1/4 turn).
smallest chainring
I MA
NO
end with the marking. After cutting the outer casing, make
SG
NO
SG
-3
0
the end round so that the inside of the hole has a uniform
E-
40