Professional Documents
Culture Documents
MODEL C
MODEL CW
Model Identification........................................................................................................................................................... 3
Design Benefits
Features and Benefits................................................................................................................................................... 4
Factory Mounted Options............................................................................................................................................. 5
Field Installed Accessories........................................................................................................................................... 6
Performance Data
Hot Water Sample Sizing Calculations......................................................................................................................... 7
Hot Water Correction Factors.................................................................................................................................... 8-9
Hot Water Performance Data (Single Row Coil)........................................................................................................ 10
Hot Water Performance Data (Two Row Coil).............................................................................................................11
Steam Sample Sizing Calculations............................................................................................................................. 12
Steam Correction Factors........................................................................................................................................... 13
Steam Performance Data........................................................................................................................................... 14
Mounting Height Correction Factors........................................................................................................................... 15
Model Dimensional / Motor Data
Model C - Floor Mounted Units................................................................................................................................... 16
Model CW - Wall Mounted Units................................................................................................................................ 17
Duct Collar Dimensional Data..................................................................................................................................... 18
Specifications
Unit Data Specifications.............................................................................................................................................. 19
Unit Mechanical Specifications................................................................................................................................... 19
The Modine Breeze AccuSpec is the fastest way to generate performance data based
on actual job conditions. The Breeze AccuSpec program is a web-based sizing and selection
program. The program provides a series of step-by-step questions that allow for the easy
configuration of Modine products. After a model has been configured, the program can
generate Submittal Schedules, Submittal Data (including performance and dimensional
drawings), and Specifications.
1,2 - Model Type (MT) 8 - Arrangement Digit Two (ADT) 12 - Access Side (AS) 16 - Motor Type (MT)
C - Pedestal Style 0 - Bottom In, Top Out L - Left S - Shaded Pole
CW - E xposed, Recessed, or 6 - Front In, Top Out R - Right P - PSC
Ceiling Unit 7 - Bottom In, Front Out H - High Static
8 - Front In, Front Out 13 - Coil Rows (CR) G - Shaded Pole with Plug-In Leads
4,5,6 - Nominal Air Flow (CFM) 1 - 1 Row Coil F - PSC with Plug-In Leads
002 - 250 CFM 9 - Development Sequence (DS) 2 - 2 Row Coil I - High Static with Plug-In Leads
003 - 330 CFM A - Current
004 - 450 CFM 14 - Access Doors (AD) 17 - Leveling Bolts (LB)
006 - 620 CFM 10 - Inlet Style (IS) 1 - None 0 - None
008 - 840 CFM L - Louvers 2 - Top 1 - Leveling Bolts
010 - 1050 CFM B - Bar Grille 3 - Front Panel
012 - 1240 CFM D - Duct Collar 4 - Top with Key Locks 18 - Outside Air (OA)
014 - 1430 CFM 5 - Front Panel with Key Locks 0 - None
11 - Outlet Style (OS) 1 - 25% OA Duct Collar
7 - Arrangement Digit One (ADO) L - Louvers 15 - Panel Fasteners (PF) 2 - 100% OA Duct Collar
0 - Wall or Floor B - Bar Grille 0 - None 3 - 25% OA Manual Damper
5 - Ceiling D - Duct Collar 1 - Spanner Head 4 - 100% OA Manual Damper
9 - Inverted A - Adjustable Louvers 2 - Key Locks 5 - 100% OA Motorized Damper
6 - 25% OA Motorized Damper
As Modine Manufacturing Company has a continuous product improvement program, it reserves the right to change design and specifications without notice.
2 11-160.7
model identification
Figure 3.4 - Standard Air Flow Options Figure 3.5 - Inverted Air Flow Options
Floor Mounted WITH FRESH AIR OPTION
(REFER TO OPTION DESCRIPTIONS)
WITH FRESH AIR OPTION
(REFER TO OPTION DESCRIPTIONS)
Floor Mounted
Recessed Wall
Model CW Model CW
Arrangement 06 Arrangement 08
Recessed Wall
Recessed Ceiling
11-160.7 3
fEATURES AND BENEFITS
4 11-160.7
Factory Mounted options
11-160.7 5
field installed accessories
Model Size A B
002-006 15 7/8" 6"
008-014 23 5/8" 6"
6 11-160.7
sample sizing calculations - hot water
11-160.7 7
correction factors - hot water
8 11-160.7
correction factors - hot water
11-160.7 9
performance data - hot water
Unit High Fan Speed Data Low Fan Speed Data Water Data
Size CFM Btu/hr WTD FAT CFM Btu/hr WTD FAT GPM WPD (ft)
10,700 44.7 100 8,200 34.1 110 0.5 0.1
11,900 24.9 104 9,100 19.0 116 1 0.1
002 250 12,400 20.0 106 150 9,500 15.2 118 1.3 0.2
12,700 17.6 107 9,700 13.4 119 1.5 0.2
12,900 13.4 107 9,800 10.2 120 2 0.3
18,000 37.5 110 12,100 25.3 117 1 0.1
20,100 27.9 116 13,600 18.9 124 1.5 0.2
003 330 22,400 20.0 123 195 15,100 13.5 131 2.3 0.3
22,700 18.9 123 15,300 12.7 132 2.5 0.4
23,000 16.0 124 15,600 10.8 134 3 0.5
20,400 42.5 102 15,100 31.4 111 1 0.1
25,200 26.3 112 18,700 19.4 124 2 0.3
004 450 28,400 20.0 118 270 21,000 14.8 132 3 0.5
30,400 15.8 122 22,500 11.7 137 4 0.7
30,700 12.8 123 22,800 9.5 138 5 0.9
37,000 38.6 115 27,100 28.2 128 2 0.3
40,700 28.3 121 29,800 20.7 134 3 0.6
006 620 44,800 20.0 127 370 32,800 14.6 142 4.7 1.0
45,300 18.9 127 33,200 13.8 143 5 1.1
46,200 16.0 129 33,800 11.7 144 6 1.4
41,900 43.6 106 31,200 32.5 113 2 0.1
47,000 24.5 112 35,100 18.3 119 4 0.2
008 840 49,000 20.0 114 545 36,600 14.9 122 5.1 0.4
50,100 17.4 115 37,400 13.0 123 6 0.5
50,100 17.4 115 37,400 13.0 123 8 0.5
50,800 35.3 105 39,600 27.5 113 3 0.1
54,700 22.8 108 42,700 17.8 117 5 0.4
010 1050 55,900 20.0 109 685 43,600 15.6 119 5.8 0.5
57,200 17.0 110 44,600 13.3 120 7 0.7
58,200 13.5 111 45,300 10.5 121 9 1.1
68,200 35.5 111 51,300 26.7 119 4 0.2
70,800 24.6 113 53,300 18.5 121 6 0.6
012 1240 72,400 20.0 114 805 54,500 15.1 122 7.5 0.9
74,200 15.4 115 55,800 11.6 124 10 1.4
74,800 13.0 116 56,300 9.8 124 12 1.8
73,800 38.4 108 56,900 29.6 116 4 0.2
76,900 26.7 110 59,300 20.6 119 6 0.6
014 1430 79,500 20.0 111 930 61,200 15.4 121 8.3 1.0
80,600 16.8 112 62,100 12.9 122 10 1.4
81,200 14.1 112 62,600 10.9 122 12 1.8
10 11-160.7
performance data - hot water
Table 11.1 - Optional High Capacity Two Row Coil at Standard Conditions
(200F Entering Water/60F Entering Air)
Unit High Fan Speed Data Low Fan Speed Data Water Data
Size CFM Btu/hr WTD FAT CFM Btu/hr WTD FAT GPM WPD (ft)
20,200 42.0 134 13,000 27.1 146 1 0.7
21,600 30.1 140 13,900 19.4 152 1.5 152.0
002 250 22,700 23.7 144 140 14,600 15.2 156 2 1.8
23,400 20.0 146 15,000 12.9 159 2.4 2.7
23,700 16.5 148 15,300 10.6 161 3 4.3
31,100 32.4 148 21,000 21.9 159 2 1.4
31,900 26.6 151 21,600 18.0 162 2.5 2.1
003 330 32,600 22.6 152 195 22,000 15.3 164 3 2.8
33,000 20.0 154 22,300 13.5 166 3.4 3.5
33,300 17.4 155 22,500 11.7 167 4 4.5
41,200 43.0 146 28,300 29.4 156 2 1.5
42,600 35.3 149 29,000 24.2 159 2.5 2.4
004 450 43,300 30.1 151 270 29,700 20.6 161 3 2.9
44,500 23.2 153 30,500 15.9 164 4 5.0
44,900 20.0 154 30,800 13.7 165 4.7 8.7
49,700 51.7 134 34,600 36.0 146 2 1.4
53,600 37.2 140 37,300 25.9 153 3 2.8
006 620 56,500 29.5 145 370 39,300 20.5 158 4 4.8
58,400 24.3 148 40,600 16.9 161 5 7.2
59,300 20.0 149 41,200 13.9 163 6.2 10.7
66,800 27.9 134 50,500 21.1 146 5 1.0
70,900 21.1 138 53,600 15.9 151 7 1.7
008 840 71,700 20.0 139 540 54,200 15.1 152 7.5 1.9
74,900 15.6 143 56,600 11.8 157 10 3.2
76,100 13.2 144 57,500 10.0 158 4.3
79,400 28.0 130 61,600 21.4 144 6 1.4
83,000 21.6 134 64,500 16.8 147 8 2.2
010 1050 84,200 20.0 135 680 65,400 15.5 149 8.8 2.5
87,600 15.2 138 68,000 11.8 152 12 4.3
88,500 13.2 138 68,700 10.2 153 14 5.8
99,000 29.4 135 76,400 22.7 149 7 1.7
102,300 23.7 137 78,900 18.3 152 9 2.6
012 1240 104,800 20.0 139 790 80,800 15.4 154 10.9 3.7
106,800 17.1 141 82,400 13.2 156 13 5.0
107,900 15.0 142 83,300 11.6 157 15 6.5
113,400 26.2 134 87,000 20.1 148 9 2.6
115,900 22.0 136 89,000 16.9 150 11 3.7
014 1430 117,200 20.0 137 915 90,000 15.4 151 12.2 4.5
119,500 16.6 138 91,800 12.7 152 15 6.5
120,600 14.8 139 92,600 11.3 153 17 8.2
11-160.7 11
sample sizing calculations - steam
12 11-160.7
correction factors - steam
Latent
Steam Steam Heat T
emperature of Entering Air (F)
Press. Temp. of
(psig) (F) Steam 30 40 50 60 70 80 90 100
0 212 970 1.19 1.11 1.03 0.96 0.88 0.81 0.74 0.67
2 219 966 1.24 1.16 1.08 1.00 0.93 0.85 0.78 0.71
5 227 961 1.29 1.21 1.13 1.05 0.97 0.90 0.83 0.76
10 239 953 1.38 1.29 1.21 1.13 1.06 0.98 0.91 0.84
The following conversion factors may be used with standard steam data Table 14.1, page 14.
Formulas: Steam
13.1) BTUA = BTUS x Factor (Table 13.1 or 13.2) Identification of Symbols
BTU = Btu/hr performance
13.2) BTUS = BTUA C = Condensate (LBS/hr.)
Factor (Table 13.1 or 13.2) E = E
ntering air temperature (F)
F = Final air temperature (F)
13.3) CA = BTUA
Latent Heat of Steam Subscripts
S = Standard operating condition (2 lbs. steam, 60F EAT)
13.4) FA = BTUA A = Actual operating conditions
+ EA
CFMA x 1.085
11-160.7 13
performance data - steam
Table 14.1 - Standard One Row Coil at Standard Conditions (2 lbs. Steam/60F Entering Air)
High Fan Speed Data Low Fan Speed Data
Coil Type Unit Size Condensate Final Air Condensate Final Air
CFM Btu/hr CFM Btu/hr
(lbs/hr) Temp (F) (lbs/hr) Temp (F)
002 250 19,800 133 21 150 14,600 156 15
003 330 28,300 139 29 195 18,000 145 19
Standard 1-Row Coil
14 11-160.7
correction factors
Mounting Height
Height at which cabinet unit heaters are installed is critical. Strong opposing drafts, large obstructions in the air stream of
Maximum mounting heights for all units are listed in the tables the unit, and higher than normal discharge air temperatures
below. The data in tables are based on operating conditions (resulting from high steam pressures) can prevent the heated
of 2 lbs. steam or 220F entering water with 60F entering air discharged by the cabinet unit from reaching the floor.
air. When operating conditions are other than those above,
refer to chart for mounting height correction factor. To obtain Under unfavorable conditions such as these, allowances must
the maximum mounting height at actual operating conditions, be made to assure maintenance of desired comfort.
multiply the appropriate factor from chart by the mounting
height in Tables. The mounting heights must be followed
closely to assure maximum comfort.
003 8 18 003 8 10
004 9 22 H 004 8 11
H
006 9 23 006 8 12
008 10 26 008 10 16
T
010 10 18 T
010 10 27
Inverted Air Flow Inverted Air Flow
012 11 26 012 11 20
Wall-Mounted Wall-Mounted
014 11 27 014 11 21
T
Maximum mounting height M
aximum mounting height
and corresponding heat and corresponding heat
throw of heaters operating H throw of heaters operating
at standard conditions (2 at standard conditions (2
H
lbs. steam or 220F entering lbs. steam or 220F entering
water, 60 T water, 60
entering air). entering air).
Table 15.3
Maximum Mounting Heights Correction Factors
These correction factors are to be used as multipliers to correct the
maximum recommended mounting heights H or heat throw T of cabinet
unit heaters when operated with steam pressures other than 2 pounds or
with water at other than entering temperature of 220F.
1.3
correction factor R
Steam Pressure
1.2 2 5 10
1.1
1.0
.9
.8
.7
.6
.5
150 160 170 180 190 200 210 220 230 240
average water temp. (F)
11-160.7 15
model C dimensional data
Figure 16.1 - Floor Model C, Sizes 002-014 Steam/Hot Water Cabinet Unit Heaters
access access
door door
43/4"
F
C
coil connections
sizes 002-006: 3/4" Npt for standard coil
51/2"
5
/8" i.d. sweat for two row coil
sizes 008-014: 1" Npt, one or two row coil
G speed control
L and j-box
N 7
/16" mounting holes
sizes 008-014 only
J
(Size 008-014 only) /2"
1
3"
Optional
Outlet
41/2" 11"
speed
control
and j-box
23/4"
K B
M 41/2" sizes
002-006
4 /8" x 3/8"
5
slotted
mounting
holes in
E filter rear
Air Inlet
flange
H
D
A
note: Left hand piping is standard, right hand piping available when specified.
Bottoms of end compartments are open for piping and electrical access.
Table 16.1 - Cabinet Dimensions (inches) Table 16.2 - Filter Dimensions (inches)
Approx. Model Size Filter Size
Unit a b c d e f g h j Shipping
Size Weight 002 8-1/2 x 20-3/4 x 1/2
lbs.
003 8-1/2 x 25-3/4 x 1/2
002 38-3/4 25 9-3/4 8 5 5-1/8 15-5/8 19-5/8 80
004 8-1/2 x 30-3/4 x 1/2
003 43-3/4 25 9-3/4 8 5 5-1/8 19-5/8 23-5/8 90
006 8-1/2 x 43-3/4 x 1/2
004 48-3/4 25 9-3/4 8 5 5-1/8 27-5/8 27-5/8 110
006 61-3/4 25 9-3/4 8 5 5-1/8 39-5/8 39-5/8 120 008 & 010 10-3/4 x 49-3/4 x 1/2
008 71-3/4 28 12 10 7 5-1/8 47-5/8 30-5/8 9-3/4 160 012 & 014 10-3/4 x 61-3/4 x 1/2
010 71-3/4 28 12 10 7 5-7/8 47-5/8 39-5/8 9-3/4 165 Filters are permanent/cleanable.
012 83-3/4 28 12 10 7 5-1/8 59-5/8 51-5/8 9-3/4 185
014 83-3/4 28 12 10 7 5-7/8 59-5/8 51-5/8 9-3/4 190
16 11-160.7
model CW dimensional data
Figure 17.1 - Wall or Ceiling Model CW, Sizes 002-014 Steam/Hot Water Cabinet Unit Heaters
F C
coil connections
sizes 002-006: 3/4" Npt for standard coil
5
/8" i.d. sweat for two row coil G
sizes 008-014: 1" Npt, one or two row coil
L Standard
N Outlet
7
/16" mounting holes
J
(Size 008-014 only) Model Sizes 008-014 only /2"
1
3"
Optional
Outlet
41/4"
speed
control
and j-box 11"
K
B
93/4"
M
Optional sizes
Inlet 002-006
4 /8" x 3/8"
5
41/4" slotted
mounting
23/4" holes in
rear
flange
Standard
Inlet A
note: Left hand piping is standard, right hand piping available when specified.
Bottoms of end compartments are open for piping and electrical access.
For inverted airflow applications, the unit is flipped 180 upside down from what is shown in Figure 17.1.
Table 17.1 - Cabinet Dimensions (inches) Table 17.2 - Filter Dimensions (inches)
Approx. Model Size Filter Size
a b c f g j Shipping
002 8-1/2 x 20-3/4 x 1/2
Unit Weight
Size lbs. 003 8-1/2 x 25-3/4 x 1/2
002 38-3/4 25 9-3/4 5-1/8 15-5/8 90 004 8-1/2 x 30-3/4 x 1/2
003 43-3/4 25 9-3/4 5-1/8 19-5/8 100 006 8-1/2 x 43-3/4 x 1/2
004 48-3/4 25 9-3/4 5-1/8 27-5/8 120
008 & 010 10-3/4 x 49-3/4 x 1/2
006 61-3/4 25 9-3/4 5-1/8 39-5/8 130
012 & 014 10-3/4 x 61-3/4 x 1/2
008 71-3/4 28 12 5-1/8 47-5/8 9-3/4 170
010 71-3/4 28 12 5-7/8 47-5/8 9-3/4 175 Filters are permanent/cleanable.
11-160.7 17
duct collar / PERMA-LAP FRAME dimensional data
Figure 18.1 - Model CW - Duct Collars Table 18.1 - Model CW - 100% Air Inlet or Outlet Duct
Collars
C A C D B E
Unit
Size a b c d e
3/4" 002 18-1/4 4-1/4 10-3/8 2-1/2 3
003 23-1/4 4-1/4 10-3/8 2-1/2 3
004 28-1/4 4-1/4 10-3/8 2-1/2 3
006 41-1/4 4-1/4 10-3/8 2-1/2 3
008 44-1/4 4-1/4 10-7/8 2-1/2 5-1/4
010 44-1/4 5-1/4 10-7/8 2-1/2 4-1/4
3/4" 012 58-1/4 4-1/4 12-7/8 2-1/2 5-1/4
014 58-1/4 5-1/4 12-7/8 2-1/2 4-1/4
B E
C A C
Figure 18.2 - Model C - Outside Air Duct Collar Table 18.2 - Model C - 25% and 100% Fresh Air Duct
Collar
Outside Air Percentage
25%
Nomen 100%
Digit 18 1, 3 or 6 2, 4 or 5
Unit Size A B C A B C
002 12 1/4 3 1/2 13 1/4 18 1/2 4 1/4 10 1/8
003 12 1/4 3 1/2 15 3/4 23 1/2 4 1/4 10 1/8
004 12 1/4 3 1/2 18 1/4 28 1/2 4 1/4 10 1/8
006 12 1/4 3 1/2 24 3/4 41 1/2 4 1/4 10 1/8
008 24 1/4 3 1/2 23 3/4 44 1/2 4 1/4 13 5/8
010 24 1/4 3 1/2 23 3/4 44 1/2 5 1/4 13 5/8
3/4" 012 24 1/4 3 1/2 29 3/4 58 1/2 4 1/4 12 5/8
B
014 24 1/4 3 1/2 29 3/4 58 1/2 5 1/4 12 5/8
UNIT SHOWN
1.50 IN DASHED LINES FOR
REFERENCE ONLY
1.50
18 11-160.7
unit / mechanical specifications
Wall or ceiling models shall have cabinets with stamped 2. The damper shall be controlled by an electric, spring-return
louvers. The entire bottom of the unit must be enclosed. Access type motor, which will be energized when the blower motor
to the speed control shall be through the easy access 16-gauge is turned on thus moving the damper to the 25% or 100%
front panels. position. It will be de-energized and close the damper when
the blower motor is off.
(Available, when specified, as optional equipment) an access
door shall be provided for speed control access. Motors, Blowers and Drives
Blowers shall be of the centrifugal, forward curved type, to
All models shall have two 9" minimum wide piping end pockets. provide even air distribution and low sound level.
All wall and ceiling units shall have safety hinged access panels All units shall have shaded pole (permanent split capacitor
that can be easily removed during installation. available when specified as optional equipment) direct-drive
motors. The motor and blower assembly shall be capable
Coils of being easily removed from the unit. Motors are built for
The heating coils shall provide specified capacities and not continuous duty to NEMA standards.
exceed the pressure drop and GPM listed in this catalog. Coils
shall be suitable for 200 PSI working pressure with 240F water Grilles (optional equipment)
or 10psi steam. When specified, aluminum linear bar inlet and/or outlet grilles
shall be provided.
Motor Speed Control
The unit shall have a unit-mounted solid state motor speed When specified, outlet may have two-way deflection louvers.
control, with high through low speeds and off positions on all
models. Filters
All air, both fresh and return, shall be filtered by a cleanable
expanded aluminum filter.
11-160.7 19
Products from Modine are designed to provide indoor air-comfort and ventilation
solutions for residential, commercial, institutional and industrial applications.
The Modine brand has been the Whatever your heating, ventilating and air conditioning requirements, Modine
has the product to satisfy your needs, including:
industry standard since Arthur B.
HVAC
Modine invented and patented
Unit Heaters:
the first lightweight, suspended Gas
Hydronic
hydronic unit heater in 1923.
Electric
No other manufacturer can Oil
Ceiling Cassettes
provide the combined application
Duct Furnaces
flexibility, technical expertise and Hydronic Cabinet Unit Heaters, Fin Tube, Convectors
fast delivery found at Modine. Infrared Heaters
Make-up Air Systems
Consult your local Modine
Unit Ventilators
distributor for help in solving your
Ventilation
indoor air problems. Packaged Rooftop Ventilation
School Products
Vertical Packaged Classroom HVAC:
DX Cooling/Heat Pump
Water/Ground Source Heat Pump
Horizontal/Vertical Unit Ventilators
Geothermal
Water-to-Water
Water-to-Air
Combination
Specific catalogs are available for each product. Catalogs 75-136 and 75-137
provide details on all Modine HVAC equipment.