Professional Documents
Culture Documents
ITEM TOTAL TOTAL ITEM TOTAL TOTAL ITEM TOTAL TOTAL ITEM TOTAL TOTAL
No.
QTY. DESCRIPTION MATERIAL LEN./AREA WEIGHT
No.
QTY. DESCRIPTION MATERIAL LEN./AREA WEIGHT
No.
QTY. DESCRIPTION MATERIAL LEN./AREA WEIGHT
No.
QTY. DESCRIPTION MATERIAL LEN./AREA WEIGHT NOTES
(M / M 2 ) (Kg.) (M / M 2 ) (Kg.) (M / M 2 ) (Kg.) (M / M 2 ) - (Kg.)
1a 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.4 32.2 3d 1 UB 203x133x30 BS EN-10025-2-S355JR 0.6 18.0 16a 1 UC 152x152x37 BS EN-10025-2-S355JR 5.0 185.0 30c7 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 0.4 1.4
GENERAL NOTES:
1b 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3e 1 UB 203x133x30 BS EN-10025-2-S355JR 4.5 135.0 16b 1 UC 152x152x37 BS EN-10025-2-S355JR 5.0 185.0 30c8 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 1.4 4.8 1. Do not scale from this drawing.
1c 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3f 1 UB 203x133x30 BS EN-10025-2-S355JR 6.0 180.0 17a 1 PFC 150x75x18 BS EN-10025-2-S355JR 1.8 32.2 30c9 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 0.4 1.4 2. All dimensions are in millimetres(mm) and all levels are in
1d 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3g 1 UB 203x133x30 BS EN-10025-2-S355JR 4.0 120.0 17b 1 PFC 150x75x18 BS EN-10025-2-S355JR 1.5 26.9 30d1 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 0.8 2.7 metres(m) AOD, unless noted otherwise.
1e 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 3h 1 UB 203x133x30 BS EN-10025-2-S355JR 6.0 180.0 17c 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.4 7.2 30d2 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 3.5 11.9 3. All Dimensions and levels to be checked on site and any
1f 2 PFC 200x75x23 BS EN-10025-2-S355JR 2.2 51.4 3j 1 UB 203x133x30 BS EN-10025-2-S355JR 4.5 135.0 17d 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.3 5.4 30d3 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 0.5 1.7 discrepancies should be reported to GHD LIVIGUNN.
1g 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3k 1 UB 203x133x30 BS EN-10025-2-S355JR 3.6 108.0 4. This drawing is to be read in conjunction with relevant project
17e 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.4 7.2 30d4 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 2.6 8.8
standards and specification.
1h 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3l 1 UB 203x133x30 BS EN-10025-2-S355JR 6.9 207.0 17f 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.3 5.4 30d5 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 1.1 3.7 5. Holes to be drilled through and fastened to gusset plates using
1j 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3m 1 UB 203x133x30 BS EN-10025-2-S355JR 1.4 42.0 17g 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.7 12.5 30d6 47 CHS 42.2x3.6, l=1040 BS EN-10210-2-S355JRH 47.9 162.9 M20 bolts.
1k 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 3n 1 UB 203x133x30 BS EN-10025-2-S355JR 1.4 42.0 17h 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.3 5.4 30d7 6 CHS 42.2x3.6, l=1175 BS EN-10210-2-S355JRH 7.1 24.1 6. Pipe supports on hold.
1l 1 PFC 200x75x23 BS EN-10025-2-S355JR 0.7 16.4 3p 1 UB 203x133x30 BS EN-10025-2-S355JR 1.6 48.0 17j 1 PFC 150x75x18 BS EN-10025-2-S355JR 1.2 21.5 31a 4 RB 50, l=100 BS EN-10025-2-S355JR 0.4 6.2
1m 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.4 32.8 3q 1 UB 203x133x30 BS EN-10025-2-S355JR 3.0 90.0 17k 1 PFC 150x75x18 BS EN-10025-2-S355JR 1.2 21.5 31b 2 RB 50, l=75 BS EN-10025-2-S355JR 0.2 3.1 STEELWORK:
1n 2 PFC 200x75x23 BS EN-10025-2-S355JR 1.6 37.4 3r 1 UB 203x133x30 BS EN-10025-2-S355JR 0.9 27.0 17l 1 PFC 150x75x18 BS EN-10025-2-S355JR 1.2 21.5 32 2 RB 20, l=170 BS EN-10025-2-S355JR 0.2 0.5
1. All works are to be carried out in accordance with the
1p 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.1 25.7 3s 1 UB 203x133x30 BS EN-10025-2-S355JR 2.7 81.0 17m 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.7 12.5 33 1 PLATE 8 thk. BS EN-10025-2-S355JR 0.2 12.6 recomendation of the of the national structural steelwork
1q 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3t 1 UB 203x133x30 BS EN-10025-2-S355JR 2.7 81.0 17n 1 PFC 150x75x18 BS EN-10025-2-S355JR 0.3 5.4 34 49 C02 - 90 ELBOW TYPE C02G32 - - 27.0 specification (NSSS) Fifth Edition 2010, CE Marking Version.
1r 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 3u 1 UB 203x133x30 BS EN-10025-2-S355JR 2.8 84.0 18a 1 SHSC 200x200x10 BS EN-10210-2-S355JRH 2.7 158.8 C05 - VARIABLE ELBOW 2. All hot rolled general steelwork and base plates to be grade
35a 22 - - 15.0
1s 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 3v 1 UB 203x133x30 BS EN-10025-2-S355JR 0.2 6.0 18b 1 SHSC 200x200x10 BS EN-10210-2-S355JRH 2.7 158.8 TYPE C05G32 S355JR to BS EN 10025-2. All structural hollow sections to be
1t 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 3w 1 UB 203x133x30 BS EN-10025-2-S355JR 4.1 123.0 19a 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 C29 - ADJUSTABLE SHORT grade S355JRH to BS EN 10210-2.
35b 4 - - 3.5 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
1u 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 3x 1 UB 203x133x30 BS EN-10025-2-S355JR 0.6 18.0 19b 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 TEE TYPE C29G32
and Holding Down Bolts designed by client. Details to be confirmed
1v 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.7 39.8 4a 1 UC 203x203x46 BS EN-10025-2-S355JR 1.4 64.5 19c 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 36 51 C03 - SHORT TEE TYPE C03G32 - - 22.4 by civil contractor.
1w 1 PFC 200x75x23 BS EN-10025-2-S355JR 0.5 11.7 4b 1 UC 203x203x46 BS EN-10025-2-S355JR 1.0 46.1 19d 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 37 38 C22 - TWO SOCKET CROSS - - 23.6 4. Steel overhead runway beams shall be tested in accordance with
1x 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.0 46.8 4c 1 UC 203x203x46 BS EN-10025-2-S355JR 1.0 46.1 19e 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 TYPE C22G32 BS 1993-6 and BS 2853.
1y 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.0 23.4 4d 1 UC 203x203x46 BS EN-10025-2-S355JR 6.4 295.5 19f 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 38 6 C28 - 36 CROSS TYPE C28G32 - - 7.0 5. All Connections forces shown are U.L.S. value.
1z 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.0 46.8 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
4e 1 UC 203x203x46 BS EN-10025-2-S355JR 0.6 27.7 19g 1 CHS 60.3x4 BS EN-10210-2-S355JRH 2.0 11.2 C18 - 90 BASE FLANGE
39 46 - - 12.0 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
1a1 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.0 46.8 4f 1 UC 203x203x46 BS EN-10025-2-S355JR 0.6 27.7 19h 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 TYPE C18G32 bolts
1a2 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.1 25.7 4g 1 UC 203x203x46 BS EN-10025-2-S355JR 1.4 64.5 19j 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 C12 - RAILING BASE FLANGE 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
40a 1 - - 1.1
1a3 1 PFC 200x75x23 BS EN-10025-2-S355JR 0.7 16.4 5a 1 UB 254x146x37 BS EN-10025-2-S355JR 2.7 99.9 19k 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 TYPE C12G32 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
1a4 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.9 44.5 5b 1 UB 254x146x37 BS EN-10025-2-S355JR 2.7 99.9 19l 1 CHS 60.3x4 BS EN-10210-2-S355JRH 1.0 5.6 63-7 ANGLE BASE FLANGE, to be 4mm fillet welds.
40b 4 - - 4.7 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
1a5 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.9 44.5 5c 1 UB 254x146x37 BS EN-10025-2-S355JR 2.7 99.9 20a 1 UB 152x89x16 BS EN-10025-2-S355JR 2.7 43.2 42.2mm OD, KEE KLAMP
galvanised coating to be min 85m. Environment category C3 to BS
1a6 1 PFC 200x75x23 BS EN-10025-2-S355JR 6.7 156.8 5d 1 UB 254x146x37 BS EN-10025-2-S355JR 2.7 99.9 20b 1 UB 152x89x16 BS EN-10025-2-S355JR 2.7 43.2 41 15 STAIRTREAD 25x5 W100 HOT DIP GALVANIZED - 109.5 EN ISO 14713-1 and design life of 25 years. The surface protection
1a7 1 PFC 200x75x23 BS EN-10025-2-S355JR 6.7 156.8 5e 1 UB 254x146x37 BS EN-10025-2-S355JR 3.2 118.4 21 1 PLATE 230x230x6mm thk. BS EN-10025-2-S355JR 0.1 4.7 853 M20 SCREW(BS 3692), BS EN ISO 898-1 - classification shall be as follows conforming to the classes defined
1a8 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.3 53.8 5f 1 UB 254x146x37 BS EN-10025-2-S355JR 5.0 185.0 22 1 PLATE 10 thk. BS EN-10025-2-S355JR 10.0 785.0 L=60 in EN BS 12944:
1a9 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.2 51.5 6a 1 UB 305x165x40 BS EN-10025-2-S355JR 6.3 253.9 23a 1 FB 100x10 thk. BS EN-10025-2-S355JR 10.2 80.6 - For any steel elements inside, not including insulated piping and
853 M20 NUTS(BS 3692) BS EN ISO 898-2 - - lagging: Class C3(Urban and Industrial atmosphere, moderate
1b1 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.2 51.5 7a 1 PFC 180x90x26 BS EN-10025-2-S355JR 0.3 7.8 23b 1 FB 100x10 thk. BS EN-10025-2-S355JR 2.2 17.4 42
sulphur dioxide levels and production areas with the high humidity).
1b2 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 7b 1 PFC 180x90x26 BS EN-10025-2-S355JR 0.3 7.8 23c 1 FB 100x10 thk. BS EN-10025-2-S355JR 1.0 7.9 - For the steel elements in the fuel storage, not including insulated
1b3 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 8a 1 EA 80x10 BS EN-10025-2-S355JR 1.6 19.0 23d 1 FB 100x10 thk. BS EN-10025-2-S355JR 0.6 4.7 1706 M20 WASHERS(BS 3692) GR 300-370 HV - and lagging: Class C4(Industrial and coastal chemical processing
1b4 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.2 51.5 8b 1 EA 80x10 BS EN-10025-2-S355JR 1.8 21.4 23e 1 FB 100x10 thk. BS EN-10025-2-S355JR 4.1 32.4 plants).
1b5 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.2 51.5 8c 1 EA 80x10 BS EN-10025-2-S355JR 1.7 20.2 23f 1 FB 100x10 thk. BS EN-10025-2-S355JR 0.8 6.3 M20 SCREW(BS 3692), - For the outside steel elements, not including insulated piping and
2 BS EN ISO 898-1 -
1b6 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.3 53.8 8d 1 EA 80x10 BS EN-10025-2-S355JR 1.5 17.9 23g 1 FB 100x10 thk. BS EN-10025-2-S355JR 5.2 41.1 L=270 lagging: Class C4(Industrial and Coastal chemical processing plants)
1b7 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.9 44.5 8e 1 EA 80x10 BS EN-10025-2-S355JR 1.7 20.2 23h 1 FB 100x10 thk. BS EN-10025-2-S355JR 0.9 7.1 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
43 4 M20 NUTS(BS 3692) BS EN ISO 898-2 - - following structure which are defined as EXC3:
1b8 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.9 44.5 8f 1 EA 80x10 BS EN-10025-2-S355JR 1.7 20.2 23j 1 FB 100x10 thk. BS EN-10025-2-S355JR 0.3 2.4
1b9
1c1
1
1
PFC 200x75x23
PFC 200x75x23
BS
BS
EN-10025-2-S355JR
EN-10025-2-S355JR
0.9
0.6
21.1
14.0
8g
8h
1
1
EA 80x10
EA 80x10
BS
BS
EN-10025-2-S355JR
EN-10025-2-S355JR
1.9
2.4
22.6
28.6
23k
23l
1
1
FB 100x10 thk.
FB 100x10 thk.
BS EN-10025-2-S355JR
BS EN-10025-2-S355JR
0.6
7.0
4.7
55.3
4 M20 WASHERS(BS 3692) GR 300-370 HV
-
Runway Beam
Brackets supporting runway beam
Column supporting brackets
ON HOLD
1c2 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.8 42.1 8j 1 EA 80x10 BS EN-10025-2-S355JR 2.4 28.6 23m 1 FB 100x10 thk. BS EN-10025-2-S355JR 2.5 19.8 44 2 SS SPRING SS - - Horizontal TIE members
1c3 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.8 42.1 8k 1 EA 80x10 BS EN-10025-2-S355JR 1.6 19.0 23n 1 FB 100x10 thk. BS EN-10025-2-S355JR 1.2 9.5 45a 112 EA 80x10, l=145 BS EN-10025-2-S355JR 16.7 198.7 Overhead crane supporting structures
(Turbine building, workshop)
1c4 1 PFC 200x75x23 BS EN-10025-2-S355JR 0.8 18.7 8l 1 EA 80x10 BS EN-10025-2-S355JR 1.9 22.6 23p 1 FB 100x10 thk. BS EN-10025-2-S355JR 3.3 26.1 45b 1 EA 80x10, l=120 BS EN-10025-2-S355JR 0.2 2.4 11. Allowance for levelling shims and grout thickness not to be less
1c5 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 8m 1 EA 80x10 BS EN-10025-2-S355JR 1.5 17.9 23q 1 FB 100x10 thk. BS EN-10025-2-S355JR 2.0 15.8 46 1 PLATE 20 thk. BS EN-10025-2-S355JR 4.0 628.0 than 15mm and no more than 25mm. May vary for large base plates.
1c6 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.4 32.8 8n 1 EA 80x10 BS EN-10025-2-S355JR 1.9 22.6 23r 1 FB 100x10 thk. BS EN-10025-2-S355JR 0.9 7.1 47 1 PLATE 25 thk. BS EN-10025-2-S355JR 0.3 58.9 12. Use non-shrink flowable grout fosroc conbextra GP or similar
1c7 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 8p 1 EA 80x10 BS EN-10025-2-S355JR 2.0 23.8 23s 1 FB 100x10 thk. BS EN-10025-2-S355JR 1.5 11.9 STEELWAY FLS 25x5, 67.0 2,299.5 approved for grouting operatiions. The grout must extend between
1c8 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 48 1 HOT DIP GALVANIZED 120mm and 50mm past the base plates edges.
8q 1 EA 80x10 BS EN-10025-2-S355JR 2.4 28.6 23t 1 FB 100x10 thk. BS EN-10025-2-S355JR 1.5 11.9 TYPE 30 x 100
13. Nominal grout thickness is 25mm u.n.o.
1c9 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.2 28.1 8r 1 EA 80x10 BS EN-10025-2-S355JR 1.9 22.6 23u 1 FB 100x10 thk. BS EN-10025-2-S355JR 3.6 28.4 49 PLATE 12 thk. BS EN-10025-2-S355JR 0.2 19 14. Access platforms, handrails, stairs, ladders shall conforming to:
1d1 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.0 23.4 8s 1 EA 80x10 BS EN-10025-2-S355JR 2.0 23.8 23v 1 FB 100x10 thk. BS EN-10025-2-S355JR 2.7 21.3 Total Net Weight: 16,472.1 BS 4952 Grating
1d2 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.4 32.8 8t 1 EA 80x10 BS EN-10025-2-S355JR 1.9 22.6 23w 1 FB 100x10 thk. BS EN-10025-2-S355JR 12.0 94.7 BS 5395/EN ISO 14122 Platform, Stairs
1d3 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 8u 1 EA 80x10 BS EN-10025-2-S355JR 1.2 14.3 24 2 FB 65x10 thk. BS EN-10025-2-S355JR 6.7 34.2 BS 8300 Handrails
1d4 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 8v 1 EA 80x10 BS EN-10025-2-S355JR 1.5 17.9 25 4 FB 50x10 thk. l=320 BS EN-10025-2-S355JR 1.3 5.1 To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
1d5 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 8w 1 EA 80x10 BS EN-10025-2-S355JR 1.1 13.1 26 8 FB 25x6 thk. l=4360 BS EN-10025-2-S355JR 34.9 34.9 with HIT-V-R Rods, minimum 270mm embedent.
1d6 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 8x 1 EA 80x10 BS EN-10025-2-S355JR 1.6 19.1 27a 1 FB 50x6 thk. BS EN-10025-2-S355JR 2.9 5.8 16. Over material (O.M.) to be cut and cut out to be applied after final
1d7 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 8y 1 EA 80x10 BS EN-10025-2-S355JR 1.7 20.2 27b 3 FB 50x6 thk. l=1945 BS EN-10025-2-S355JR 5.9 11.8 dimension check.
1d8 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 9a 1 UC 203x203x71 BS EN-10025-2-S355JR 3.8 269.8 28 2 EA 75x10, L=100 BS EN-10025-2-S355JR 0.2 2.2 17. - Indidacates area on base plate for drilling holes for
1d9 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 10a 1 UC 152x152x23 BS EN-10025-2-S355JR 4.0 92.0 29 29 RB 20, L=400 BS EN-10025-2-S355JR 11.6 29.0 chemical anchors.
1e1 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 10b 1 UC 152x152x23 BS EN-10025-2-S355JR 5.0 115.0 30a 6 CHS 42.2x3.6, l=894 BS EN-10210-2-S355JRH 5.4 18.4
1e2 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.3 53.8 10c 1 UC 152x152x23 BS EN-10025-2-S355JR 4.0 92.0 30b 6 CHS 42.2x3.6, l=1535 BS EN-10210-2-S355JRH 9.3 31.6
1e3 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.3 30.4 10d 2 UC 152x152x23, l=275 BS EN-10025-2-S355JR 0.6 13.8 30c 6 CHS 42.2x3.6, l=1230 BS EN-10210-2-S355JRH 7.4 25.2 REFERENCE DOCUMENTS:
1e4 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 11a 1 CHS 88.9x5 BS EN-10210-2-S355JRH 3.7 38.1 30d 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 2.4 8.2 - KEY PLAN - BARRY_01_DWG_23_20700
1e5 1 PFC 200x75x23 BS EN-10025-2-S355JR 3.0 70.2 11b 1 CHS 88.9x5 BS EN-10210-2-S355JRH 2.2 22.7 30e 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 10.1 34.3 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
1e6 1 PFC 200x75x23 BS EN-10025-2-S355JR 1.1 25.7 11c 1 CHS 88.9x5 BS EN-10210-2-S355JRH 2.2 22.7 30f 4 CHS 42.2x3.6, l=201 BS EN-10210-2-S355JRH 0.2 0.7 - C & S REPORT (REP) - BARRY_01_20076
1e7 1 PFC 200x75x23 BS EN-10025-2-S355JR 2.1 49.1 11d 1 CHS 88.9x5 BS EN-10210-2-S355JRH 1.7 17.5 30g 20 CHS 42.2x3.6, l=1440 BS EN-10210-2-S355JRH 28.9 112.9 - C & S REPORT (REP) - BARRY_01_20077
1e8 1 PFC 200x75x23 BS EN-10025-2-S355JR 0.8 18.7 11e 1 CHS 88.9x5 BS EN-10210-2-S355JRH 1.7 17.5 30h 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 0.4 1.4 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
1e9 1 PFC 200x75x23 BS EN-10025-2-S355JR 0.8 18.7 11f 2 CHS 88.9x5, l=810 BS EN-10210-2-S355JRH 1.7 17.5 30j 1 CHS 42.2x3.6 BS EN-10210-2-S355JRH 0.8 2.4 Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
STEELWORK:
N. 56.000m - DRAWING LIMIT 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
LADDER TO STEELWAY
TURBINE OR APPROVED EQUIVALENT
WITH SELF-CLOSING GATE
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
PIT grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
COVER and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
TURBINE/WALFARE BUILDING 4. Steel overhead runway beams shall be tested in accordance with
COLUMNS UC 305x305x97
PIT GRATING/STEELWORK REFER DRAWING BS 1993-6 and BS 2853.
SHALL HAVE A HINGED TYPE BARRY_01_DWG_07_20612 5. All Connections forces shown are U.L.S. value.
OPENING TO ALLOW FOR PUMP 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
REMOVAL & MAINTENANCE
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
4887
BEARING OF 5kN/m2
- For any steel elements inside, not including insulated piping and
lagging: Class C3(Urban and Industrial atmosphere, moderate
PFC 200x75x23
PFC 200x75x23
TAW (Turbine building, workshop)
2 11. Allowance for levelling shims and grout thickness not to be less
TYPE 8 TYPE 3 TYPE 3
458
1b8 (SHT.18) 2c (SHT.17) (SHT.17) 1c1 than 15mm and no more than 25mm. May vary for large base plates.
PFC 200x75x23 SIMILAR PFC 200x90x30 SIMILAR PFC 200x90x30 SIMILAR 1 12. Use non-shrink flowable grout fosroc conbextra GP or similar
1005
1c2 approved for grouting operatiions. The grout must extend between
UC 203x203x46
PF
4a PS - 579 UPH 1 1c3
C
2e 1b9 120mm and 50mm past the base plates edges.
20
TYPE 79a
UC 203x203x46
PFC 200x90x30
0
1g5
x7
2d
5x
H TYPE 4 (SHT.17)
TYPE 3 TYPE 3 H (SHT.8) 13. Nominal grout thickness is 25mm u.n.o.
800
23
1g9
3a 3b G1 (SHT.17)
PFC 200x75x23
PS - 585 UPH (SHT.17) PS - 587 UPH PFC 200x75x23 (SHT.17) PFC 200x75x23 PFC 200x75x23
1g8
14. Access platforms, handrails, stairs, ladders shall conforming to:
1350
PFC 200x90x30
PFC 200x90x30
TYPE 9b TYPE 8
2g (SHT.18) (SHT.18) G1 (SHT.9) BS 5395/EN ISO 14122 Platform, Stairs
730
PFC 200x75x23 TYPE 3 1b6 2g 1b4 BS 8300 Handrails
TYPE 4 TYPE 3 TYPE 3 1b5 TYPE 3 TYPE 3 1b3 TYPE 1
1b7 (SHT.17) 4g SIMILAR
G 1g4 SIMILAR
(SHT.17)
PFC 200x90x30
SIMILAR PFC 200x90x30 PFC 200x75x23 G (SHT.9) PFC 200x75x23
(SHT.17)
PFC 200x75x23
(SHT.17)
PFC 200x75x23
(SHT.17) To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
2a 2b 1a8 1a9 1b1 1b2 16. Over material (O.M.) to be cut and cut out to be applied after final
715
dimension check.
Y (SHT.10) X (SHT.10) W(SHT.10) V (SHT.10) V (SHT.10) TYPE 1
(SHT.17)
TYPE 1
17. - Indidacates area on base plate for drilling holes for
2292
(SHT.17)
PFC 200x75x23
PS - 582 UPH PS - 586 UPH chemical anchors.
TURBINE F 1u F (SHT.7)
3990
ACCESS REFERENCE DOCUMENTS:
1a6 1a7 - KEY PLAN - BARRY_01_DWG_23_20700
PLATFORM - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
- C & S REPORT (REP) - BARRY_01_20076
4000
2585
- C & S REPORT (REP) - BARRY_01_20077
E. 191.600m - CONT. ON DRAWING BARRY_01_DWG_23_20719
PFC 200x75x23
PFC 200x75x23
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
7976
Z U T S R Q P N Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
6678
Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
PS - 590 Plan El 13.500
TYPE 1 TYPE 1 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
(SHT.17) (SHT.17)
PFC 200x75x23 Sections A, B, P, R
2966
568 655 128 735 540 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
PS - 576 UPH PS - 577 UPH PS - 578 UPH PS - 589 UPH Sections C, D.
E E (SHT.7)
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
700
1t
TYPE 1 TYPE 1 1m TYPE 3 1q TYPE 3 1r TYPE 1 TYPE 3 TYPE 1 Hall Sections E, F, G
(SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17)
1465
PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
1015
Revision
PFC 200x75x23
TYPE 9a 1p 1f (SHT.17)
D PFC 200x75x23
1l TYPE 2 TYPE 3 TYPE 3
1a2
TYPE 1 TYPE 3 TYPE 1
D (SHT.8)
HARRIS PYE UK LIMITED,
1658
PFC 200x75x23 (SHT.17) PFC 200x75x23 (SHT.17) PFC 200x75x23 (SHT.17) PFC 200x75x23 (SHT.17) (SHT.17) (SHT.17) HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
TYPE 1 TYPE 3
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
NEAR COWBRIDGE
800
(SHT.17) (SHT.17)
1k
1g 1h 1a1 1j VALE OF GLAMORGAN, CF71 7PB
C TYPE 8 1x 1y 1z C (SHT.7) www.harrispye.com
935
(SHT.18) TYPE 3
PFC 200x75x23
(SHT.17)
PFC 200x75x23 TYPE 1 TYPE 1 TYPE 3 TYPE 3
TYPE 2 (SHT.17) (SHT.17)
PFC 200x75x23 (SHT.17) PFC 200x75x23
(SHT.17)
PFC 200x75x23 PFC 200x75x23
660
290
1b 1c 1d 1e
TAW A A (SHT.7)
1
N. 42.000m - CONT. ON DRAWING BARRY_01_DWG_09_20723 488 290 2222 1404 550 1047 2461 539 1140 1175 473
PROJECT
1350 3000 3000 3000
PS - 599A UPH
PS - 607 UPH
PS - 608A
- For the steel elements in the fuel storage, not including insulated
Y W FOR EARTHING ATTACHMENT
DETAILS REFER DRAWINGS
M J and lagging: Class C4(Industrial and coastal chemical processing
CHANGED TO BOLTED plants).
BARRY_01_DWG_18_60401/60402
- For the outside steel elements, not including insulated piping and
150 790 1070 995 lagging: Class C4(Industrial and Coastal chemical processing plants)
FOR VERTICAL LADDER
DET. REF. SHT.16 TYPE 21b 21 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
(SHT.21) TYPE 10 TYPE 22 230 LONG x 6 THICK PLATE following structure which are defined as EXC3:
(SHT.21)
3d
(SHT.18) TYPE 18 TYPE 11 WELDED TO FLANGES OF 3c Runway Beam
(SHT.20)
ON HOLD
(SHT.18)
UB 254x146x37 PS - 665
UB 203x133x30
TAW Brackets supporting runway beam
2 Column supporting brackets
UB 203x133x30
8f Horizontal TIE members
PS - 664
3x 760 5e
688
8d Overhead crane supporting structures
810
(SHT.17) 8e 1d4
TYPE 1 (Turbine building, workshop)
PFC 200x75x23
PFC 200x75x23
1255
SIMILAR
EA
10
550
x10
11. Allowance for levelling shims and grout thickness not to be less
80x
PFC 200x75x23
80
80
x10
9a than 15mm and no more than 25mm. May vary for large base plates.
EA
EA
1c8 7a 3c
12. Use non-shrink flowable grout fosroc conbextra GP or similar
444
H UC 203x203x71 1n UB 254x146x37
5d
PS - 608
H (SHT.8)
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
TYPE 17 TYPE 14 13. Nominal grout thickness is 25mm u.n.o.
(SHT.20) (SHT.19)
TYPE 25 TYPE 25 TYPE 12 14. Access platforms, handrails, stairs, ladders shall conforming to:
F (SHT.19) TYPE 13
F (SHT.7)
PFC 200x75x23
PFC 200x75x23
(SHT.22) (SHT.22)
(SHT.19) BS 4952 Grating
PS - 609 TPS
1c7
12.290m
1260
AT EL.
1261
PS - 625
x10
947
80
FOR COOLING WATER PIPE SUPPORT SETOUT FOR STEELWORK REFER SPIG
8c 5f BS 8300 Handrails
EA
DETAILS REFER DRAWING REFER SHEET NO.2 CONSTRUCTION DRAWINGS 6a To steelway or approved equivalent supplier.
G 5c
G (SHT.9) 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
TURBINE PIPING UB 254x146x37
with HIT-V-R Rods, minimum 270mm embedent.
4995
Y (SHT.10)
W (SHT.10)
ACCESS 16. Over material (O.M.) to be cut and cut out to be applied after final
PLATFORM TYPE 15 TYPE 17 TYPE 14
dimension check.
A4 A4
UB 254x146x37
PFC 200x75x23
(SHT.20) (SHT.20) (SHT.19) (SHT.10)
UB 305x165x40
TYPE 16 17. - Indidacates area on base plate for drilling holes for
875
PS - 614 TPS
PS - 613 TPS
(SHT.20) 1d2 chemical anchors.
P
1218
1d1
1363
1365
EA
PFC 200x75x23
6531
80
PS - 610 FPS
x10
1c6 PFC 200x75x23
490
450
TYPE 15
(SHT.20) UB 254x146x37
5b REFERENCE DOCUMENTS:
- KEY PLAN - BARRY_01_DWG_23_20700
300
A2 A2
7975
(SHT.10)
E. 191.600m - CONT. ON DRAWING BARRY_01_DWG_23_20719
PS - 615 TPS
TYPE 17 TYPE 14 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
PFC 200x75x23
(SHT.20) (SHT.20) - C & S REPORT (REP) - BARRY_01_20076
789
T R Q 1c5
635
1c4 TYPE 19 - C & S REPORT (REP) - BARRY_01_20077
1115
PFC 200x75x23
35
0
(SHT.21)
x1
A1 A1 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
80
(SHT.10)
EA
8a 1c9 7b Plan El 10.400m
(SHT.17) (SHT.17)
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
328
328
TYPE 1 TYPE 1 UB 254x146x37
SIMILAR PS - 612 Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
TYPE 18 TYPE 23
E TYPE 15
(SHT.20) (SHT.20) (SHT.22) E (SHT.7) Plan El 13.500
TYPE 20
5a
HOLD
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
PS - 643
(SHT21) Sections A, B, P, R
12.943m
AT EL.
PS - 611 TPS
PS - 604
1463
1465
Sections C, D.
10d 10a 10d
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
UC 152x152x23 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
TYPE 21
Rev Date Description By Chk App
TYPE 26 TYPE 26
(SHT.22) (SHT.22) (SHT.21)
Revision
947
HARRIS PYE UK LIMITED,
1515
HANGER 5 & 6, BONA ROAD
C C (SHT.7)
LLANDOW TRADING ESTATE,
NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
B B (SHT.7)
TAW
1
CLIENT
N. 42.000m - CONT. ON DRAWING BARRY_01_DWG_09_20723
3917 548
PROJECT
T (SHT.10)
R (SHT.10)
Q (SHT.10)
P (SHT.10)
M (SHT.9)
J (SHT.9)
4887
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
6460
TYPE 27
REFERENCE DOCUMENTS:
(SHT.22) - KEY PLAN - BARRY_01_DWG_23_20700
E. 191.600m - CONT. ON DRAWING BARRY_01_DWG_23_20719
AT LEVEL
PS - 604
PS - 606
12.943m
12.249m
4568
TYPE 30
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
(SHT.23) Sections C, D.
TYPE 38 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
(SHT.26)
TYPE 28 TYPE 31 3f TYPE 30 TYPE 33 3g TYPE 36 TYPE 30 TYPE 39 3w TYPE 42 Hall Sections E, F, G
(SHT.23) (SHT.24) (SHT.23) (SHT.25) (SHT.26) (SHT.23) (SHT.27) (SHT.28)
UB 203x133x30 UB 203x133x30 UB 203x133x30 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
Rev Date Description By Chk App
0 EA
80x
1 80x 8v 8x 8y 1d9 8z Revision
EA 10 10 8w
80x 1d8 11a
UB 203x133x30
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
1225
EA
UB 203x133x30
UB 203x133x30
EA (SHT.27) 10
EA
0 0
x1 x1 HARRIS PYE UK LIMITED,
80
80 80 80 80x
1518
x10
CHS
80x
8s 8u EA EA
x1
0 EA 88.9 HANGER 5 & 6, BONA ROAD
C C (SHT.7)
10
x5
3h 8t 3m 3j 1d7 3n 3k 3p LLANDOW TRADING ESTATE,
TYPE 43
25
(SHT.28)
NEAR COWBRIDGE
UB 203x133x30 UB 203x133x30 UB 203x133x30 VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
290
UB 203x133x30
TYPE 30 TYPE 32 TYPE 35 TYPE 37 TAW
(SHT.23) (SHT.24) (SHT.25) (SHT.26)
(SHT.23) 1
TYPE 29 TYPE 34 TYPE 40 TYPE 44
(SHT.27) (SHT.28) CLIENT
N. 42.000m - CONT. ON DRAWING BARRY_01_DWG_09_20723 1548 1958 3l
PS - 598 UPH
PS - 603
PS - 597
PS - 605
PS - 602
PS - 599
PS - 600
PS - 601
PROJECT
1978 1978 1979 885 1386 800 1394 3506 3325
5935 4465 6835
BARRY - BIOMASS UK No 2 LLP
TITLE
T (SHT.10) Q (SHT.10) P (SHT.10) M (SHT.9) J (SHT.9)
TURBINE PLATFORM
PLAN - EL 13.750m FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
1:50 A1 ES/MU
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
34,29
DO NOT SCALE - IF IN DOUBT ASK
4
SITE NOTES
TR
UE GENERAL NOTES:
1. Do not scale from this drawing.
TAW TAW TAW TAW 2. All dimensions are in millimetres(mm) and all levels are in
A B C D metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
M J PIPE SUPPORT TYPE (PS) 4. This drawing is to be read in conjunction with relevant project
standards and specification.
5935 4465 6835 PS-XXX-FPS - "F" POST PIPE SUPPORT 5. Holes to be drilled through and fastened to plates
PS-XXX-TPS - "T" POST PIPE SUPPORT 6. Pipe supports on hold.
PS-XXX-PPS - PIPE TO PIPE SUPPORT
PS-XXX-UPS - UNDER PLATFORM PIPE SUPPORT
PS-XXX-UPH - UNDER PLATFORM PIPE HANGER STEELWORK:
PS-XXX - PIPE TO PIPE RACK SUPPORT
1. All works are to be carried out in accordance with the
5650 790 395
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
N. 56.000m - DRAWING LIMIT 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
UB 254x102x28 BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
TYPE 45 TYPE 46 TYPE 46 TYPE 47 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
(SHT.29)
13a (SHT.29) (SHT.29)
(SHT.29)
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
1550
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
PFC 200x75x23 classification shall be as follows conforming to the classes defined
TYPE 48 TYPE 48 in EN BS 12944:
UB 254x102x28
UB 254x102x28
- For the steel elements in the fuel storage, not including insulated
1585
4886
and lagging: Class C4(Industrial and coastal chemical processing
LOCATION OF A 1.5 TON LIFTING 1079 1064 plants).
DAVIT TO AID VALVE REMOVAL TO - For the outside steel elements, not including insulated piping and
GROUND LEVEL 13b 13c lagging: Class C4(Industrial and Coastal chemical processing plants)
PFC 200x75x23 PFC 200x75x23 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
TYPE 48
(SHT.29) (SHT.29) Runway Beam
ON HOLD
(SHT.29)
TYPE 49 TYPE 50 TYPE 48
(SHT.29)
1e7
SIMILAR
1e8 Brackets supporting runway beam
1038
Column supporting brackets
PFC 200x90x30
2f
1g1 Horizontal TIE members
TYPE 52 1e6 TYPE 53
TYPE 51 (SHT.30) (SHT.30)
Overhead crane supporting structures
(SHT.30)
PFC 200x75x23 PFC 200x75x23 PFC 200x75x23
(Turbine building, workshop)
FOR EARTHING ATTACHMENT 11. Allowance for levelling shims and grout thickness not to be less
DETAILS REFER DRAWINGS
BARRY_01_DWG_18_60401/60402
EA
80
8h
8j 80
x10 EA
80
1f8
TYPE 48
(SHT.29)
HOLD than 15mm and no more than 25mm. May vary for large base plates.
715
x10
EA x1
0
12. Use non-shrink flowable grout fosroc conbextra GP or similar
TYPE 54 TYPE 58
(SHT.30) (SHT.32) approved for grouting operatiions. The grout must extend between
UB 356x171x45
TAW 120mm and 50mm past the base plates edges.
2 13. Nominal grout thickness is 25mm u.n.o.
12c 8k 14. Access platforms, handrails, stairs, ladders shall conforming to:
TYPE 57
BS 4952 Grating
810
758 (SHT.31)
H 1n
TYPE 55
TYPE 56
(SHT.31)
H (SHT.8) BS 5395/EN ISO 14122 Platform, Stairs
PFC 200x75x23 8l (SHT.31) BS 8300 Handrails
To steelway or approved equivalent supplier.
TURBINE PIPING TYPE 49 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
2100
10
80x
ACCESS PLATFORM (SHT.29) with HIT-V-R Rods, minimum 270mm embedent.
EA
1f6 1f7 16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
PFC 200x75x23
PFC 200x75x23
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
1e5
PFC 200x75x23
FOR VERTICAL LADDER TYPE 60
TYPE 3 TYPE 3
DET. REF. SHT.16
(SHT.17) (SHT.17) (SHT.32) REFERENCE DOCUMENTS:
TYPE 59
(SHT.32)
- KEY PLAN - BARRY_01_DWG_23_20700
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
8m - C & S REPORT (REP) - BARRY_01_20076
1f4 1f5 12b
- C & S REPORT (REP) - BARRY_01_20077
9825
2140
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
PFC 200x75x23
PFC 200x75x23
UB 356x171x45
UB 356x171x45
EA
80x
Plan El 10.400m
0 1
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
TYPE 61 Plan El 10.400m
(SHT.32) - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
1e4 Plan El 13.500
8078
E. 191.600m - CONT. ON DRAWING BARRY_01_DWG_23_20719
PFC 200x75x23
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
TYPE 1 TYPE 60 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
387
TYPE 49 TYPE 62 (SHT.17) (SHT.32)
PFC 200x75x23 Sections C, D.
UB 203x133x30
(SHT.29) 8n (SHT.33)
PFC 200x75x23
0
x1 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
80 TYPE 30
EA TYPE 60
(SHT.23) 1e3 Hall Sections E, F, G
503
3r (SHT.32)
A7 1f3
PS - 620
A7(SHT.10) A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
PFC 200x75x23
PFC 200x75x23
1e2
EA
890
1f2 472
80
TYPE 24 TYPE 24
x10
PS - 642
(SHT.35) (SHT.35) HARRIS PYE UK LIMITED,
PS - 618 UPH HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
1e1 NEAR COWBRIDGE
415
8p
VALE OF GLAMORGAN, CF71 7PB
A6 PFC 200x75x23
PS - 621 A6(SHT.10) www.harrispye.com
TYPE 60
TYPE 49 (SHT.32)
(SHT.29)
8q TYPE 64
(SHT.33) CLIENT
PFC 200x75x23
1545
x10
80
12a 1f1
EA
3q TYPE 66
(SHT.34)
UB 203x133x30
TAW PROJECT
1
TYPE 65 TYPE 30
BARRY - BIOMASS UK No 2 LLP
100
(SHT.34)
N. 42.000m - CONT. ON DRAWING BARRY_01_DWG_09_20723
A5 A5(SHT.10)
TITLE
1072 1858
SPIG DIA.1700 DUCT SHALL BE
TURBINE PLATFORM
3505 2930 395 INSTALLED & SUPPORTED BEFORE THE
INSTALLATION OF THE PLATFORM FABRICATION DRAWING
STEEL WORK
SCALE DRAWING SIZE DRAWN
M (SHT.9) J (SHT.9) 1:50 A1 ES/MU
PLAN - EL 15.475m DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
34,29
DO NOT SCALE - IF IN DOUBT ASK
4
SITE NOTES
TR
UE GENERAL NOTES:
1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
standards and specification.
5. Holes to be drilled through and fastened to plates
6. Pipe supports on hold.
STEELWORK:
1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
TAW TAW TAW 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
B C D and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
1955 4498 6835
4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
1950 2335 2170 1550 577 390 675 1210 473 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
34 215 bolts
TYPE 73 TYPE 73 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
TAW (SHT.35) TYPE 70 (SHT.35) 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
(SHT.35)
2 to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
433
57
1050
classification shall be as follows conforming to the classes defined
TYPE 69 TYPE 69 TYPE 69 TYPE 69 TYPE 69 TYPE 68 TYPE 67 in EN BS 12944:
(SHT.35) - For any steel elements inside, not including insulated piping and
622
(SHT.35)
622
1443
Runway Beam
TYPE 68 TYPE 67
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
(SHT.35) (SHT.35)
Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
2510
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
7975
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
TYPE 68 TYPE 67
(SHT.35)
TYPE 72 REFERENCE DOCUMENTS:
(SHT.35) (SHT.35)
- KEY PLAN - BARRY_01_DWG_23_20700
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
- C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
1465
Plan El 13.500
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
TYPE 68 TYPE 68 TYPE 71 TYPE 68 TYPE 71 TYPE 68
TYPE 71 TYPE 68 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
(SHT.35) (SHT.35)
(SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
Rev Date Description By Chk App
Revision
895
TYPE 67 TYPE 67 TYPE 67 TYPE 67 TYPE 67 TYPE 67
(SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35)
HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
620
TAW CLIENT
1
1350 450
BARRY - BIOMASS UK No 2 LLP
1800 2550 3000 3000 2748
TITLE
TURBINE PLATFORM
TURBINE PLATFORM FOOTPRINTS FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
1:50 A1 ES/MU
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
TAW
220
D NOTES
65
TYP
10
22
4 NOS.
GENERAL NOTES:
2854
TAW TAW TAW TAW C10 C10
TYP
150
947 1. Do not scale from this drawing.
A B C D 1f9
PFC 200x75x23 2. All dimensions are in millimetres(mm) and all levels are in
Scale 1:20 SHSC 90x
14h 350 300 242 metres(m) AOD, unless noted otherwise.
90x5
3. All Dimensions and levels to be checked on site and any
PFC 180x
7b
discrepancies should be reported to GHD LIVIGUNN.
500
90x26
456
SHSC 90x
90x5 14m 4. This drawing is to be read in conjunction with relevant project
UB 254x146x37 EL 12.750 T.O.S.
standards and specification.
5. Holes to be drilled through and fastened to plates
225 6. Pipe supports on hold.
TYP 15 22
TYP
(SHT.20) 150 22
10
5a
PFC 150x75x18
17n STEELWORK:
2135
C10
150
FOR HANDRAIL DET. 1. All works are to be carried out in accordance with the
UC 152x152x23
REF. SHT.11
Scale 1:20 recomendation of the of the national structural steelwork
22 specification (NSSS) Fifth Edition 2010, CE Marking Version.
1140
3985
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
700
PFC 150x75x18
17m 1t 10c
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
EL 9.915 T.O.S PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 EL 9.915 T.O.S. PFC 200x75x23
TYP 1 and Holding Down Bolts designed by client. Details to be confirmed
TYP 1
(SHT.17)
(SHT.17) by civil contractor.
SHSC 70x70x5
SHSC 70x70x5
TYP 1 TYP 3 TYP 3 TYP 3 TYP 1 22 TRIPPING 4. Steel overhead runway beams shall be tested in accordance with
1150
(SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17)
1b 1c 1d 1e BKT. BS 1993-6 and BS 2853.
488 335
5. All Connections forces shown are U.L.S. value.
15p 15q
EL 8.764 U/S EL 8.764 U/S 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
BASE PLATE BASE PLATE Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
TYP 68 TYP 67 TYP 72 bolts
(SHT.35) (SHT.35) (SHT.35)
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
675 1210 473
to be 4mm fillet welds.
5447 4953 5187
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
SECTION A-A SECTION E-E classification shall be as follows conforming to the classes defined
in EN BS 12944:
- For any steel elements inside, not including insulated piping and
lagging: Class C3(Urban and Industrial atmosphere, moderate
TAW sulphur dioxide levels and production areas with the high humidity).
D - For the steel elements in the fuel storage, not including insulated
TAW TAW TAW TAW 2855 and lagging: Class C4(Industrial and coastal chemical processing
plants).
A B C D - For the outside steel elements, not including insulated piping and
300 242 lagging: Class C4(Industrial and Coastal chemical processing plants)
PFC 180x90x26
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
7a following structure which are defined as EXC3:
EL 12.750 T.O.S Runway Beam
60
TYP 12 TYP 17
UB 254x146x37
TYP 13 TYP 14
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
(SHT.19) (SHT.20) 5d (SHT.19) (SHT.19)
C15
Overhead crane supporting structures
22
(Turbine building, workshop)
175
~10~
11. Allowance for levelling shims and grout thickness not to be less
1336 2140
than 15mm and no more than 25mm. May vary for large base plates.
2835
P1
800 C15
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
1140 120mm and 50mm past the base plates edges.
FOR HANDRAIL STAIRCASE 13. Nominal grout thickness is 25mm u.n.o.
TYPICAL
SHSC 90x90x5
427
60x175x10 1u
864
DET. REF. SHT.11 17 NOS 14. Access platforms, handrails, stairs, ladders shall conforming to:
TYP 2 14a 22 22 TRIPPING BKT 38
(SHT.17) TYP 1 BS 4952 Grating
EL 9.915 T.O.S PFC 200x75x23 PFC 200x75x23
60x175x10 60x175x10 EL 9.915 T.O.S. (SHT.17)
PFC 200x75x23
TRIPPING BKT TRIPPING BKT BS 5395/EN ISO 14122 Platform, Stairs
TYP 1 BS 8300 Handrails
3 (SHT.17)
x2 22 TRIPPING
5 To steelway or approved equivalent supplier.
SHSC 70x70x5
SHSC 70x70x5
x7 TYP 8
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
00
TYP
1150
1150
1150
8 2 (SHT.18) 22 BKT.
P FC 1g2 1a 15s 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
36
75x172x10
15a 15b
TRIPPING BKT
15c 15d 15e 15f with HIT-V-R Rods, minimum 270mm embedent.
1a4
EL 8.764 U/S EL 8.764 U/S 16. Over material (O.M.) to be cut and cut out to be applied after final
BASE PLATE BASE PLATE dimension check.
TYP 67 TYP 67 TYP 67 TYP 67 TYP 67 TYP 67 TYP 68 15r TYP 67
(SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) 17. - Indidacates area on base plate for drilling holes for
chemical anchors.
675 1683
4135 1350 450 335 2215 1915 1085 3000 1065 1683
17b TYP 21
(SHT.21) TAW TAW HARRIS PYE UK LIMITED,
EL 12.249 T.O.S.
1 2 HANGER 5 & 6, BONA ROAD
10d 10a 10d PFC 150x75x18 LLANDOW TRADING ESTATE,
NEAR COWBRIDGE
7975
TYPE 80 VALE OF GLAMORGAN, CF71 7PB
(SHT.36) www.harrispye.com
17a 6688 219 1336 8
1336
CLIENT
UC 152x152x37
UC 152x152x37
UC 152x152x23
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
00 15n x2
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
3
C2 (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17)
1145
8 PF 1g3 1g 1h 1j 1k 1a7
1a5 15g 15h 15j 15k 15l
15f 15q 15s
1g8
1c3
BARRY - BIOMASS UK No 2 LLP
EL 8.764 U/S EL 8.764 U/S EL 8.770 U/S
BASE PLATE BASE PLATE BASE PLATE
TYP 68 TYP 68 TYP 71 TYP 68 TYP 71 TYP 68 TYP 71 TYP 68 TYP 67 TYP 67 TYP 67 TYP 67
(SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) (SHT.35) TITLE
1044 558
1960 2175 1350 450 2550 1365 TURBINE PLATFORM
620 2360 2510 1443 1602
5935
1915
4465
550 1085 2423
6835
577
FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
1:50 A1 ES / MU
SECTION C-C SECTION K-K DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
GENERAL NOTES:
1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
225 discrepancies should be reported to GHD LIVIGUNN.
17h 150 4. This drawing is to be read in conjunction with relevant project
TYP
10
standards and specification.
5. Holes to be drilled through and fastened to plates
BKT 100 x 100 x 10 =280= =280= C10
6. Pipe supports on hold.
150
22
SIM TO OPP SIDE
4 NOS. 17f
PFC 150x75x18 PFC 150x75x18
TAW TAW STEELWORK:
700
17d
TAW TAW TAW C10 C10 C10 C10
TAW 1 2
PFC 150x75x18
TYP
TYP
400
A B C TYP D 1. All works are to be carried out in accordance with the
17c 17e 17g recomendation of the of the national structural steelwork
PFC 200x75x23 specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
22
6687 229 1336
S355JR to BS EN 10025-2. All structural hollow sections to be
SIM TO
OPP SIDE
grade S355JRH to BS EN 10210-2.
2 NOS. 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
BKT 100 x 100 x 10 329 895 761 731
22
SIM TO OPP SIDE and Holding Down Bolts designed by client. Details to be confirmed
4 NOS. by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
17m FOR HANDRAIL STAIRCASE
BS 1993-6 and BS 2853.
PFC 150x75x18
PFC 150x75x18
DET. REF. SHT.11
17g 5. All Connections forces shown are U.L.S. value.
700
TYP
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
EL 9.915 T.O.S. PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 EL 9.915 TOS PFC 200x75x23
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
PF
bolts
C2
PFC 200x75x23 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
SHSC 70x70x5
TYP 1 TYP 1 TYP 1 TYP 1 TYP 1 TYP 1 TYP 3 TYP 1 TYP 3 TYP 3 TYP 3 TYP 1 TYP 1 TYP 3 TYP 9b 00
1145
1150
x7
1151
(SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.17) (SHT.18) 5x
1m 1q 1r 1s 1a6 23 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
1g9
15e 15l 15p 15r 15m to be 4mm fillet welds.
1c2
EL 8.764 U/S EL 8.764 U/S 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
BASE PLATE BASE PLATE galvanised coating to be min 85m. Environment category C3 to BS
TYP 67 TYP 68 TYP 68 TYP 68 TYP 68
620
(SHT.35)
895
(SHT.35)
1465
(SHT.35)
2510
(SHT.35) (SHT.35)
1443 1044 558 EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
7975 in EN BS 12944:
- For any steel elements inside, not including insulated piping and
4098 1838 4467 2760 735 540 1150 1648
lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
plants).
- For the outside steel elements, not including insulated piping and
UB 152x89x16
20a 20b lagging: Class C4(Industrial and Coastal chemical processing plants)
SECTION D-D SECTION L-L 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
2682
following structure which are defined as EXC3:
11f
Runway Beam
ON HOLD
CH
Brackets supporting runway beam
S
57
88.
Column supporting brackets
9x5
Horizontal TIE members
Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
TYPE 55,56 TYPE 75
(SHT.31) than 15mm and no more than 25mm. May vary for large base plates.
(SHT.36)
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
TAW TAW TAW TAW 120mm and 50mm past the base plates edges.
A B C D 13. Nominal grout thickness is 25mm u.n.o.
3330 14. Access platforms, handrails, stairs, ladders shall conforming to:
1035 1110 1185 BS 4952 Grating
PFC 150x75x18
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
PS - 627 To steelway or approved equivalent supplier.
17l
UB 152x89x16
UB 152x89x16
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
1665
16. Over material (O.M.) to be cut and cut out to be applied after final
20a 20b dimension check.
17k
2682
17. - Indidacates area on base plate for drilling holes for
PFC 150x75x18
PS - 616 chemical anchors.
17j
968
158
PS - 617
PFC 150x75x18
UB 356x171x45 EL 15.475 T.O.S.
REFERENCE DOCUMENTS:
TYP 58
TAW - KEY PLAN - BARRY_01_DWG_23_20700
(SHT.32)
1 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
TYP 54 TYPE 55 TYPE 56 - C & S REPORT (REP) - BARRY_01_20076
(SHT.30) (SHT.31) (SHT.31)
12c TYP 57 - C & S REPORT (REP) - BARRY_01_20077
(SHT.31)
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
FOR HANDRAIL DET. Plan El 10.400m
2725
REF. SHT.12 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
UC 203x203x46
Plan El 13.500
723 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
TYP 22
(SHT.20) Sections A, B, P, R
UB 254x146x37 EL 12.750 T.O.S. - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
TYP 21 TYP 10 TYP 18 TYP 11 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
(SHT.21) (SHT.18) (SHT.20) (SHT.18) Hall Sections E, F, G
6710
UB 203x133x30
5e 3d
230 LONG x 6thk A0 22-08-2017 ISSUED FOR REVIEW ES/MU MM/RK SM
PLATE WELDED
TO FL OF B7 Rev Date Description By Chk App
4d 1950
21
FOR HANDRAIL STAIRCASE Revision
DET. REF. SHT.11
3985
TYPE 77 22 HARRIS PYE UK LIMITED,
(SHT.37) HANGER 5 & 6, BONA ROAD
60x175x10 LLANDOW TRADING ESTATE,
2c 1c1 TRIPPING BKT NEAR COWBRIDGE
EL 9.915 T.O.S 1x 1f VALE OF GLAMORGAN, CF71 7PB
PFC 200x75x23 PFC 200x90x30 PFC 200x90x30 PFC 200x75x23 TYP 3 www.harrispye.com
(SHT.17)
3
EL 9.915 T.O.S. PFC 200x75x23
x2
UC 203x203x46
UC 203x203x46
75 x5 CHS
0x TYP 8 88.9 88.9 TYP 3
SHSC 90x90x5
20
1150
SHSC 70x70x5
CHS x5
4
C (SHT.18) 2d (SHT.17) 1b9
.3x
PF 1g5
688
100
60
TYP 3
SHSC 70x70x5
45
S
11b 14k CLIENT
CH
(SHT.17)
1b8 4b 11c 4c
EL 8.764 U/S
BASE PLATE 15h 15b 19e
TYPE 76 TYPE 76 EL 8.764 U/S
TYP 73 TYP 70 TYP 73 TYP 73 BASE PLATE
8 (SHT.35) (SHT.36) (SHT.35) (SHT.35) (SHT.36) (SHT.35)
15g
33
1962 1985 1955 1950 2550 3505 804 800 1721 TYP 68
(SHT.35)
TYP 67
PROJECT
5902 4500 6833 (SHT.35)
293 325 895
BARRY - BIOMASS UK No 2 LLP
TITLE
TURBINE PLATFORM
SECTION H-H SECTION U-U FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
1:50 A1 ES / MU
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
GENERAL NOTES:
TAW TAW TAW TAW TAW TAW
A B A B C D 1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
standards and specification.
5. Holes to be drilled through and fastened to plates
6. Pipe supports on hold.
STEELWORK:
1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
UC 203 x 203 x 71 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
FOR HANDRAIL STAIRCASE 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
DET. REF. SHT.11 651 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
18a 18b
bolts
3525
TYPE 78 TYPE 78 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
1b3
TYP 5 (SHT.37) (SHT.37) 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
(SHT.17)
EL 9.915 T.O.S PFC 200x75x23 UB 203x133x30 UB 203x133x30 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
23
5x galvanised coating to be min 85m. Environment category C3 to BS
752
x7
SHSC 90x90x5
SHSC 90x90x5
SHSC 90x90x5
SHSC 70x70x5
SHSC 70x70x5
TYP 7 TYP 6 TYP 5 TYP 4 TYP 3 TYP 3 TYP 3 TYP 9b TYP 8
SHSC 90x90x5
SHSC 90x90x5
00
C2 EN ISO 14713-1 and design life of 25 years. The surface protection
1150
3s 16. Over material (O.M.) to be cut and cut out to be applied after final
UB 203x133x30
FOR HANDRAIL DET. dimension check.
2682
2682
(SHT.10) REF. SHT.12 17. - Indidacates area on base plate for drilling holes for
A5 chemical anchors.
5
5
.9x
.9x
88
11e
88
45
45
S
11d
S
CH
CH
1173
1173
12b 13c TYP 63 TYP 49 TYP 59 TYP 49
(SHT.33) (SHT.29) (SHT.32) (SHT.29) REFERENCE DOCUMENTS:
EL 15.475 T.O.S. EL 15.475 T.O.S. UB 356x171x45
- KEY PLAN - BARRY_01_DWG_23_20700
UC 203x203x46
UB 254x102x28
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
UB 356x171x45
TYPE 74 TYP 57 TYP 46 TYP 65
TYPE 74
TYP 49 TYP 51 - C & S REPORT (REP) - BARRY_01_20076
4e TYP 66 (SHT.31) (SHT.29) (SHT.34) 4f (SHT.29) (SHT.30)
(SHT.34) (SHT.36) (SHT.36) 12a FOR SAFETY GATE DET. - C & S REPORT (REP) - BARRY_01_20077
1725
9393
Plan El 13.500
SHSC 90x90x5
1246
SHSC 90x90x5
TYP 43 TYP 42
1000
1000
969
40 (SHT.28) (SHT.28)
724
3p
14l Sections A, B, P, R
456
EL 12.750 T.O.S. UB 254x146x37 SHSC 90x90x5 UB 305x165x40 EL 12.750 T.O.S. - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
TYP 21 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
TYP 15
TYP 23 TYP 11 Hall Sections E, F, G
(SHT.22) A3 (SHT.18)
(SHT.21) (SHT.20)
TYP 1 TYP 15 TYP 15 TYP 12
UC 203x203x46
SHSC 90x90x5
UB 152x152x23
5f 6a (SHT.17) TYP 21
(SHT.20) (SHT.20) (SHT.19) (SHT.21) A0 22-08-2017 ISSUED FOR REVIEW ES/MU MM/RK SM
220 260 220
85 65 Rev Date Description By Chk App
20
65 46
2835
TYP TYP
4985
TYP Revision
10b 46 46 22 4d
C10 C10 C10 C10 C10 C10
TYP
TYP
TYP
150
150
150
649
3986
400
17e VALE OF GLAMORGAN, CF71 7PB
EL 9.915 T.O.S. Scale 1:20 www.harrispye.com
Note: 4 plate stiffiners for item
no.22 (1 on each side post)
TYP 1
1150
(SHT.17)
TYP 2
(SHT.17) PFC 200x75x23
1a3 CLIENT
EL 8.764 U/S EL 8.764 U/S
BASE PLATE BASE PLATE
TYP 72 TYP 71 75x172x10 TYP 73
(SHT.35) (SHT.35) 22 (SHT.35)
TRIPPING BKT
1515 6460
2980 4996 4885
7975 4885 PROJECT
7976
PFC 150x75x18
17b TYP 34
5. Holes to be drilled through and fastened to plates
1501
1576
(SHT.25) 3m 6. Pipe supports on hold.
CH
TYPE 81
S
60
(SHT.37)
.3x
STEELWORK:
4
TAW 19g
1 TYP 26
(SHT.22) 1. All works are to be carried out in accordance with the
3835
3835
3835
recomendation of the of the national structural steelwork
TYPE 82 specification (NSSS) Fifth Edition 2010, CE Marking Version.
UC 152x152x37
UC 152x152x37
(SHT.37) 2. All hot rolled general steelwork and base plates to be grade
4985
4985
4985
1950 =250=
16b 16a S355JR to BS EN 10025-2. All structural hollow sections to be
2334
622 1950
grade S355JRH to BS EN 10210-2.
22 22 PFC 200x75x23 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
PFC 150x75x18 1g6
17c 60x175x10 and Holding Down Bolts designed by client. Details to be confirmed
SHSC 90x90x5
60x175x10
TRIPPING BKT
864
TRIPPING BKT TYP 1 14a by civil contractor.
PFC 200x75x23 1a1 1z 1y
1a2 TYP 3 (SHT.17)
4. Steel overhead runway beams shall be tested in accordance with
400
SHSC 70x70x5
SHSC 70x70x5
PFC 200x75x23
4
.3x
TYP 1 TYP 1 4 22 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
688
688
100
100
x
60
(SHT.17) (SHT.17) 0.3 TYP 3 TYP 2
1150
1150
1150
1150
1150
SHSC 70x70x5
SHSC 70x70x5
45
S
45
TYP 3 6 170
CH
S (SHT.17) 60x175x10 (SHT.17) Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
(SHT.17) CH
TRIPPING BKT bolts
22 15d 15j
15k 19d 15c 19f 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
EL 8.764 U/S 60x175x10 EL 8.764 U/S EL 8.764 U/S EL 8.764 U/S EL 8.764 U/S EL 8.764 U/S
BASE PLATE TRIPPING BKT BASE PLATE BASE PLATE BASE PLATE BASE PLATE BASE PLATE 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
TYP 67 TYP 68 TYP 71 TYP 71 to be 4mm fillet welds.
(SHT.35) (SHT.35) (SHT.35) (SHT.35)
TYP 68 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
(SHT.35)
TYP 67 galvanised coating to be min 85m. Environment category C3 to BS
(SHT.35)
EN ISO 14713-1 and design life of 25 years. The surface protection
295 935 1015 295 325 895 1518 293 325 895 295 938 1013 1515 classification shall be as follows conforming to the classes defined
in EN BS 12944:
- For any steel elements inside, not including insulated piping and
SECTION N-N SECTION P-P SECTION Q-Q SECTION R-R SECTION S-S SECTION T-T lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
plants).
- For the outside steel elements, not including insulated piping and
TAW TAW TAW TAW TAW TAW lagging: Class C4(Industrial and Coastal chemical processing plants)
2 2 2 2 1 D 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
=220= Overhead crane supporting structures
65 (Turbine building, workshop)
TYP 11. Allowance for levelling shims and grout thickness not to be less
657 200
TYP
20
10
EXISTING 46 than 15mm and no more than 25mm. May vary for large base plates.
655 245
REFERENCE FOR HANDRAILS DET. 12. Use non-shrink flowable grout fosroc conbextra GP or similar
REF. SHT.11 C10 C10
22 approved for grouting operatiions. The grout must extend between
TYP
150
120mm and 50mm past the base plates edges.
SHSC 20x200x10
2212
13. Nominal grout thickness is 25mm u.n.o.
TYP 26 14. Access platforms, handrails, stairs, ladders shall conforming to:
1332
(SHT.22) 643 1015
550
BOLTED TO UNDERSIDE 18b TYP 26 Scale 1:20 BS 4952 Grating
1332
EL 11.530 U/S SPIG 3x (SHT.22) PFC 200x90x30 37 BS 5395/EN ISO 14122 Platform, Stairs
OF SPIG DUCT SUPPORT
SHSC 20x200x10
2k
2380
DUCT SUPPORT BEAM STRUCTURE 18a
PFC 200x90x30
BS 8300 Handrails
2j To steelway or approved equivalent supplier.
2380
1350 1350
630
PFC 200x90x30 TYP 1 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
2l 60x175x10
SHSC 90x90x5
12 (SHT.17)
22
1615
969
1350 TYP 6 UC 203x203x46
630
418
PFC 200x90x30 UC 203x203x46 (SHT.18) (SHT.18) TYP 1
2g 4g EL 9.915 T.O.S. 75x172x10 EL 9.915 T.O.S. 22 EL 9.915 T.O.S. (SHT.17) EL 12.750 T.O.S. dimension check.
TYP 3 TYP 4 PFC 200x90x30 PFC 200x75x23
TRIPPING BKT
418
(SHT.17) TYP 3 (SHT.17) 90x181x10 17. - Indidacates area on base plate for drilling holes for
EL 9.915 T.O.S. EL 9.915 T.O.S. (SHT.17) TRIPPING BKT
SHSC 70x70x5
SHSC 70x70x5
CH
CH
TYP 3 TYP 3 chemical anchors.
648
648
S
S
TYP 4
688
100
100
4
45
TYP 8
UC 203x203x46
60
60
.3x
SHSC 70x70x5
45
(SHT.17)
45
(SHT.17)
1150
1150
TYP 3
.3x
.3x
CH 19k (SHT.17) 19l
60
S (SHT.18)
4
4
S
(SHT.17)
648
60
648
CH
100
100
45
UC 203x203x46
15a
45
.3x
1140
1150
=220=
Revision
UB 203x133x30
65
20
C15
TYP
~10~ HARRIS PYE UK LIMITED,
185
22
150
3u NEAR COWBRIDGE
660 VALE OF GLAMORGAN, CF71 7PB
UB 203x133x30
UB 203x133x30
10 www.harrispye.com
TYP 3t 3s
2683
Scale 1:20 2931
EL 13.996 T.O.S.
=350= 3q TYP 66
PFC 200x75x23
TYP 65 TYP 30 (SHT.34) CLIENT
14l 1g7 (SHT.34) (SHT.23)
1246
SHSC 90x90x5
PFC 200x90x30
2m
SHSC 90x90x5
159
3v =500= 1w
724
8h 8j
901
EL 12.750 T.O.S. EL 12.750 T.O.S. EL 12.750 T.O.S. EL 15.475 T.O.S. EL 15.475 T.O.S. (SHT.32)
PFC 200x75x23 UB 254x146x37 UC 203x203x46 UC 203x203x46 PFC 200x75x23
4f 4e
29
EA
29
10
80x
10 80x
EL 14.574 T.O.S. EA
TYP 18
TYP 2 (SHT.18)
TYP 16 TYP 17 TYP 14 TYP 30 PROJECT
(SHT.17) TYP 15 TYP 84 14j TYP 84 (SHT.23) 1e3
1d1 (SHT.20) (SHT.20) 5c (SHT.20) (SHT.19) (SHT.33) (SHT.33)
B5 (SHT.14) STEELWORK:
1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
B6 S355JR to BS EN 10025-2. All structural hollow sections to be
TAW grade S355JRH to BS EN 10210-2.
2 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
(SHT.13) 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
B3 B3 5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
B6 (SHT.14) Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
890
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
B2 B2 B5 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
(SHT.13)
galvanised coating to be min 85m. Environment category C3 to BS
B1 B1 (SHT.13)
EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
in EN BS 12944:
- For any steel elements inside, not including insulated piping and
lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
plants).
- For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
8296
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
4768
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
REFERENCE DOCUMENTS:
B8 - KEY PLAN - BARRY_01_DWG_23_20700
(SHT.14) - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
- C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
400
PROJECT
C1 C1 (SHT.14) STEELWORK:
1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
2920 and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
189 2730 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
2636
230
C4 C6 (SHT.15)
C4 to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
(SHT.14)
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
in EN BS 12944:
725
- For any steel elements inside, not including insulated piping and
lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
plants).
- For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
729
735
3259
Column supporting brackets
6869
3563
Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
4804
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
SEE VERTICAL SEE VERTICAL
1879
BS 4952 Grating
LADDER DETAILS LADDER DETAILS BS 5395/EN ISO 14122
BS 8300
Platform, Stairs
Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
3497
400
C6 REFERENCE DOCUMENTS:
- KEY PLAN - BARRY_01_DWG_23_20700
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
- C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
1146
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
C5 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
A0 24-08-2017
22-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
B9 B9
(SHT.14)
Rev Date Description By Chk App
Revision
C2
HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
CLIENT
PROJECT
CHS 42.2x3.6(TYP)
5. Holes to be drilled through and fastened to plates
30z 30z 30z 30z 30z 30z 30z 30z 30z
6. Pipe supports on hold.
TYP
30d 30e
530
35a 37 37 37 37 37 37 37 37 37
STEELWORK:
1080
TYP
35b
30c
1. All works are to be carried out in accordance with the
TYP
30f 30g 23b 30j 30g 30g 30g 30g 30g 30g
100
23a
TYP
35a recomendation of the of the national structural steelwork
550
30d6
TYP
39 39 39 39 39 39 39 39 39
10
specification (NSSS) Fifth Edition 2010, CE Marking Version.
EL 9.915 T.O.S FB 100x10 FB 100x10 2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
33a x2
3 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
75
38 20
0x and Holding Down Bolts designed by client. Details to be confirmed
FC 1g2
R100
P by civil contractor.
41 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
36
CHS 42.2x3.6(TYP)
34 30u
30z 30l Runway Beam
30n
35a
ON HOLD
TYP
530
30z 30z 30z 30z Brackets supporting runway beam
35a 229 37 30p 30g 30g 37 Column supporting brackets
34
Horizontal TIE members
1080
1080
TYP
35b Overhead crane supporting structures
30b 30f 30m 37 37 36 36
(Turbine building, workshop)
30b3
11. Allowance for levelling shims and grout thickness not to be less
30r than 15mm and no more than 25mm. May vary for large base plates.
TYP
550
30c 255 545 23e 30z
30d6
TYP
35a
100
23f 12. Use non-shrink flowable grout fosroc conbextra GP or similar
23c 39 39 39 39
approved for grouting operatiions. The grout must extend between
657
FB 100x10 FB 100x10
40b
15 16. Over material (O.M.) to be cut and cut out to be applied after final
TYP dimension check.
TYP
195
195
165
33
SHT.14 SHT.14
22d
10
23d
2225
2225
2225
PROJECT
40b 40b
41
1b7 1b8 BARRY - BIOMASS UK No 2 LLP
36
36
33 33
TITLE
CHS 42.2x3.6(TYP)
30b 34 30b
30a3 30a6 CH
30z 30z 30z 30z 30z 35a S
42
.2 x3
STEELWORK:
.6(
30g 30g 30g 30g 30a5 233 TY
P)
35a 1. All works are to be carried out in accordance with the
36 35a
recomendation of the of the national structural steelwork
1080
35b 35b
37 37 37 37 37
specification (NSSS) Fifth Edition 2010, CE Marking Version.
30c 30c 2. All hot rolled general steelwork and base plates to be grade
30a4 30z 30a7
S355JR to BS EN 10025-2. All structural hollow sections to be
CHS 42.2x3.6(TYP)
23l 229
grade S355JRH to BS EN 10210-2.
39 39 39 39 39
FB 100x10 FB 100x10 FB 100x10 40a 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
35a 35a
and Holding Down Bolts designed by client. Details to be confirmed
2225
2225
30a by civil contractor.
30a 4. Steel overhead runway beams shall be tested in accordance with
PF
C2
PF
C BS 1993-6 and BS 2853.
0 20
0x
75
x2
0x
75
x2
5. All Connections forces shown are U.L.S. value.
3 3
1g8
38 1g9 38
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
R100 R100 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
30d6 30d6 bolts
1145
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
41 40b 41 40b 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
1c3 1c2 to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
36
galvanised coating to be min 85m. Environment category C3 to BS
36
33 33
EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
22d in EN BS 12944:
22d
- For any steel elements inside, not including insulated piping and
DETAILS
DETAILS SIM TO SEC A9-A9 lagging: Class C3(Urban and Industrial atmosphere, moderate
SIM TO SEC A9-A9 sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
SECTION B4-B4 SECTION B5-B5 and lagging: Class C4(Industrial and coastal chemical processing
plants).
- For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
TAW TAW Runway Beam
D D Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
880 292 400 1395 1577 396 1445 1527 396 Overhead crane supporting structures
TYP TYP
995 400 365 830 250
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
CHS 42.2x3.6(TYP) CHS 42.2x3.6(TYP) CHS 42.2x3.6(TYP) than 15mm and no more than 25mm. May vary for large base plates.
34 34 34 12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
CHS 42.2x3.6(TYP)
36 36 36 36
CHS 42.2x3.6(TYP)
CHS 42.2x3.6(TYP)
CHS 42.2x3.6(TYP)
30a8 30y 30a1 30c5 30c8 120mm and 50mm past the base plates edges.
TYP
TYP
530
530
30z 30z
30u 30z 30z 30u 13. Nominal grout thickness is 25mm u.n.o.
30a9 30b1 30z 30c6 30c9 30d1 14. Access platforms, handrails, stairs, ladders shall conforming to:
CHS 42.2x3.6(TYP) CHS 42.2x3.6(TYP) BS 4952 Grating
1080
1080
TYP
TYP
TYP
550
550
TYP
100
100
TYP
chemical anchors.
10
10
SECTION B6-B6 SECTION B7-B7 SECTION B8-B8 SECTION B9-B9 SECTION C1-C1 REFERENCE DOCUMENTS:
- KEY PLAN - BARRY_01_DWG_23_20700
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
- C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
TYP
95
10
TYP
22
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
TYP
134
22
Plan El 10.400m
TYP - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
170 x 75 x 8 33 33 170 x 75 x 8 Plan El 13.500
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
10 75 800 75 Sections A, B, P, R
TAW TYP
2 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
SECTION C3-C3 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
SEE SAFETY GATE A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
TAW
DETAILS D
Rev Date Description By Chk App
Revision
856 3497 735 2636 152 2730 291
HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
497 1500 1500 85 550 100 1500 1136 250 1240 1240 LLANDOW TRADING ESTATE,
928 572 NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
CHS 42.2x3.6(TYP) CHS 42.2x3.6(TYP) www.harrispye.com
34
CHS 42.2x3.6(TYP)
36 36 34 34 36 36 36
CHS 42.2x3.6(TYP)
30d2 30d4 30b2
30z 30z 30z 30u 30z 30z CLIENT
30z 30z
30d3 30g 30g 30g 30d5 30t 30t
30b3
CHS 42.2x3.6(TYP)
37 37 36 36 37 37 37
34
36 36 36 36 36 36 34 34 34
STEELWORK:
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
CHS 42.2x3.6
34 30b7 34 30b8 30c1
30u 30z 30z 30u 30z 30z 30z 30z 30z 30z 30z 1. All works are to be carried out in accordance with the
30u 30x 30x 30b3 30u 30g 30c2 recomendation of the of the national structural steelwork
30b6 specification (NSSS) Fifth Edition 2010, CE Marking Version.
CHS 42.2x3.6 CHS 42.2x3.6 CHS 42.2x3.6 CHS 42.2x3.6 CHS 42.2x3.6
2. All hot rolled general steelwork and base plates to be grade
37 37 37 37 37 37
S355JR to BS EN 10025-2. All structural hollow sections to be
36 36 36
CHS 42.2x3.6
CHS 42.2x3.6
34 30b3 30b3 34 34 30b3 34 30b9 grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
39 39 23p 23q
23n CHS 42.2x3.6 39 39 and Holding Down Bolts designed by client. Details to be confirmed
39 39 39 39 39
FB 100x10 FB 100x10 FB 100x10 FB 100x10 FB 100x10 by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
23r 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
SECTION C5-C5 SECTION C6-C6 to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
in EN BS 12944:
- For any steel elements inside, not including insulated piping and
lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
CHS 42.2x3.6
and lagging: Class C4(Industrial and coastal chemical processing
CHS 42.2x3.6 C18G32 Fast Clamp plants).
FB100x10
Base Flange - For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
FB100x10 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
C18G32 Fast Clamp FB 100x10
25 50 50 25 following structure which are defined as EXC3:
Base Flange
Runway Beam
ON HOLD
100
Brackets supporting runway beam
TYP
10
30 28
Column supporting brackets
58
45
T.O.S Horizontal TIE members
90
Overhead crane supporting structures
45 45 18
10
(Turbine building, workshop)
90 11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
TYPICAL STANCHEON BASE DETAILS IWO HANRAILS BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
50 17. - Indidacates area on base plate for drilling holes for
chemical anchors.
90 550 94
ROUND BAR HOLE - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
32 Plan El 10.400m
CHS 42.2x3.6(TYP)
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
55
20 ROUND
BAR - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
130
31a Sections A, B, P, R
34 34
175
M20 BOLT
30c3 43 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
50 ROUND
BAR Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
65
150
65
150
Hall Sections E, F, G
STOPPER WELDED TO
T
CU
75
45
R32,5
50 ROUND Rev Date Description By Chk App
HINGE 1
290
250
BAR
890
Revision
22e
L1 = 50
20
HANGER 5 & 6, BONA ROAD
HR
LLANDOW TRADING ESTATE,
150
36 36 NEAR COWBRIDGE
30c3
R20 VALE OF GLAMORGAN, CF71 7PB
31a
www.harrispye.com
360
30c4 30c4
75
50 ROUND
50
BAR
HINGE 2
134
34 M20 WASHER 27
CLIENT
44 50 2 145
34 TYP
190
SS SPRING
30c3
(The spring is shown full compressed. When
10
L2
TYP
22
50
420 3. All Dimensions and levels to be checked on site and any
TO SUIT M20
C9 C9 discrepancies should be reported to GHD LIVIGUNN.
TYP
100
4. This drawing is to be read in conjunction with relevant project
50
120
5. Holes to be drilled through and fastened to plates
TYP
50
FB 50x5
27b 6. Pipe supports on hold.
EA 75x10
28 420 28
EA 75x10
STEELWORK:
SECTION C7-C7 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
Scale 1:10
1140
specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
1330
R355
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
27b
FB 50x5 TYP 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
361
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
70 galvanised coating to be min 85m. Environment category C3 to BS
30
TYP
EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
in EN BS 12944:
TYP
- For any steel elements inside, not including insulated piping and
150
877
877
FB 50x5
27a lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
FB 50x5 - For the steel elements in the fuel storage, not including insulated
TYP
150
60 27b
and lagging: Class C4(Industrial and coastal chemical processing
516
516
TYP
plants).
1500
=65=
TYP
- For the outside steel elements, not including insulated piping and
4380
4380
TYP
lagging: Class C4(Industrial and Coastal chemical processing plants)
TYP
216
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
TYP
109
following structure which are defined as EXC3:
2725
Runway Beam
221 280
722
221
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
C9 C9
50
6700
6700
BS 4952 Grating
289 BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
DET.1 D2 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
FB 25x5
26 26
FB 25x5 D1 D1 with HIT-V-R Rods, minimum 270mm embedent.
1500
16. Over material (O.M.) to be cut and cut out to be applied after final
EL 12.750m dimension check.
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
100
FB 50x10
25
=50=
REFERENCE DOCUMENTS:
C8 C8 - KEY PLAN - BARRY_01_DWG_23_20700
50
50
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
DETAIL-1 - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
Scale 1:5 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
2835
Hall Sections E, F, G
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
FB 65x10 70 420 70 30 40 420 70 Rev Date Description By Chk App
24
Revision
2200
2200
PFC 200x75x23
100
1n
125
R10 HANGER 5 & 6, BONA ROAD
25
LLANDOW TRADING ESTATE,
NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
50
FB 50x10 FB 50x10
25 25 www.harrispye.com
258
75
TYP
25
50
PFC 200x75x23
CLIENT
42
1n
RB20
29 22
TO SUIT M20
EA 75x10
28
10
C7 C7 400
PROJECT
EL 10.400m
TYP BARRY - BIOMASS UK No 2 LLP
SECTION D1-D1 SECTION D2-D2
Scale 1:5 Scale 1:5 TITLE
TURBINE PLATFORM
FABRICATION DRAWING
VERTICAL LADDER DETAILS SCALE DRAWING SIZE DRAWN
Scale 1:15 NTS A1 ES/MU
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
GENERAL NOTES:
45a 1. Do not scale from this drawing.
P1 2. All dimensions are in millimetres(mm) and all levels are in
PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
standards and specification.
PFC 200x75x23
PFC 200x75x23
PFC 200x75x23
5. Holes to be drilled through and fastened to plates
45a 45a 6. Pipe supports on hold.
D3 D3 D4 D4
80 80 80 80
STEELWORK:
80 80
45 35 35 45 35 45 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
TOP VIEW TOP VIEW TOP VIEW
35
35
35
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
145
145
145
75
75
75
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
35
35
35
4. Steel overhead runway beams shall be tested in accordance with
22 22 22 BS 1993-6 and BS 2853.
TYP 45a TYP 45a 45a
TYP 5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
10 10 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
60 10 10 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
PFC 200x75x23
ITEM NO.45a PFC 200x75x23
ITEM NO.45a ITEM NO.45a 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
21 Nos. 5 Nos. 40 Nos. to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
63
63
63
C15
galvanised coating to be min 85m. Environment category C3 to BS
22 P1 EN ISO 14713-1 and design life of 25 years. The surface protection
(5 NOS.) classification shall be as follows conforming to the classes defined
175
~10~
75
75
75
45a 45a 45a 45a in EN BS 12944:
- For any steel elements inside, not including insulated piping and
lagging: Class C3(Urban and Industrial atmosphere, moderate
63
63
63
C15 sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
22 22 10 10 and lagging: Class C4(Industrial and coastal chemical processing
TO SUIT M20 TO SUIT M20 22 plants).
TYP
TO SUIT M20 - For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
SECTION D3-D3 SECTION D4-D4 SECTION D4-D4 Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
TYPE 1 TYPE 2 TYPE 3 approved for grouting operatiions. The grout must extend between
21 Locations 5 Locations 20 Locations 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
UC 203x203x46
P4 220
16. Over material (O.M.) to be cut and cut out to be applied after final
PFC 200x75x23
75 85 60
D7 dimension check.
17. - Indidacates area on base plate for drilling holes for
33 chemical anchors.
80 80
TYP
35
D6a
20
100
45 35
PFC 200x90x30
~8~
P2
P5 P4
PFC 200x75x23 C15 REFERENCE DOCUMENTS:
35
22
UB 203x133x30
P2 85 TYP UB 203x133x30 UB 203x133x30
- KEY PLAN - BARRY_01_DWG_23_20700
141 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
UC 203x203x46
145
75
300
370
35
35
P3 33 75 33
TYP 45a C15 Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
D6 P6a
145
75
~10~
66
Plan El 13.500
~10~ - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
P6
190
22
D6a D6 Sections A, B, P, R
35
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
207
35
75
22 ~10~ D6 D6 22 Sections C, D.
TO SUIT M20 TYP - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
P5 49 C15
22 D7 Hall Sections E, F, G
66
11
PFC 200x75x23 P5
90
66
C15
63
UB 203x133x30
CLIENT
22 P6
C15
75
P3 P6 P6
~10~ ~10~
75
181
45a
203
181
P2 P2 22
98
(2 NOS.)
(1 NO.)
59
P3b
181
~10~
PROJECT
63
C15 22
UB 203x133x30 UB 203x133x30 22
P3a
TO SUIT M20
10
22 C15 BARRY - BIOMASS UK No 2 LLP
108
TYP
20
~10~ 60 85 75
100
GENERAL NOTES:
P8 C15 E2b
1. Do not scale from this drawing.
35
85
2. All dimensions are in millimetres(mm) and all levels are in
D8 141 141
metres(m) AOD, unless noted otherwise.
UC 203x203x46
PFC 200x75x23
E1
PFC 200x75x23
22 3. All Dimensions and levels to be checked on site and any
UB 203x133x30
P9 TYP 33 75 33 33 75 33
discrepancies should be reported to GHD LIVIGUNN.
2 Nos.
PFC 200x75x23
4. This drawing is to be read in conjunction with relevant project
P10 P1 standards and specification.
35
35
66 5. Holes to be drilled through and fastened to plates
141 BRAKET
370
300
PFC 200x75x23 33 75 33 FOR TYPE 9a 6. Pipe supports on hold.
PFC 200x75x23 PFC 200x75x23 ~10~ ~10~
145
145
ONLY
75
75
~12~
C15
22 22 STEELWORK:
66
35
35
22
1. All works are to be carried out in accordance with the
~10~ TYP 22 recomendation of the of the national structural steelwork
P11
190
P7
207
TYP specification (NSSS) Fifth Edition 2010, CE Marking Version.
75
XL H ~10~ E2a E2a 2. All hot rolled general steelwork and base plates to be grade
E1
35
S355JR to BS EN 10025-2. All structural hollow sections to be
D7 D7 22
D9 grade S355JRH to BS EN 10210-2.
66
C15
49 E2b 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
22
TYP
TOP VIEW P10 TOP VIEW P11 by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
6 Nos. 1 No.
BS 1993-6 and BS 2853.
TOP VIEW P7 P8 P7b 5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
2 Nos. Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
2 Nos. 1 No. 60 75 66
10 10 bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
190 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 PFC 200x75x23 to be 4mm fillet welds.
92 98
P9 P9 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
C15
63
63
BRAKET galvanised coating to be min 85m. Environment category C3 to BS
11
P9 P9 FOR TYPE 9a EN ISO 14713-1 and design life of 25 years. The surface protection
22 ONLY classification shall be as follows conforming to the classes defined
P10 P10 P1
175
~10~ in EN BS 12944:
75
75
PFC 200x75x23 UB 203x133x30 P11
(2 NOS.) - For any steel elements inside, not including insulated piping and
31
63
63
203
181
C15
22 - For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
145
P7
22 10 22 plants).
TO SUIT M20 TO SUIT M20
P7b P7b
- For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
24
UC 203x203x46
11
following structure which are defined as EXC3:
VIEW D9 SECTION E1-E1 SECTION E2a-E2a SECTION E2b-E2b Runway Beam
P7a
P7a
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
1 No.
SECTION D7-D7 SECTION D8-D8 Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
TYPE 7 TYPE 8 TYPE 9a TYPE 9b approved for grouting operatiions. The grout must extend between
1 Location 3 Locations 1 Location 1 Location 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
155 BS 8300 Handrails
To steelway or approved equivalent supplier.
40 75 40
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
E3 75 87 E5 16. Over material (O.M.) to be cut and cut out to be applied after final
40
dimension check.
22 17. - Indidacates area on base plate for drilling holes for
chemical anchors.
155
75
P12 P12 ~10~
UB 254x146x37 UB 254x146x37
40
P12
22
REFERENCE DOCUMENTS:
TYP - KEY PLAN - BARRY_01_DWG_23_20700
252 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
5
14
101
- C & S REPORT (REP) - BARRY_01_20076
115 137
P14
P14 -
-
C & S REPORT (REP) - BARRY_01_20077
BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
P12 1 No.
E4 E4 Plan El 10.400m
TYP 22 E6 E6 196
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
~10~ ~10~ 49 85 Plan El 10.400m
22 - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
136
145
P
22
155
TO SUIT M20
UB 254x146x37
TY
Plan El 13.500
10
TYP
x
22
80
84 43 22 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
~10~
233
EA
TYP
Sections A, B, P, R
57
269
75 48
E5
158
160
22 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
EA
=8 TYP Sections C, D.
80
62
PFC 200x75x23
0=
x10
97
255
71
P15
10
22 22 Hall Sections E, F, G
114
58
80x
TO SUIT M20
EA
68
97
P13
95
79
=80
TY = 129 123
Revision
P
E3
P12 P13 116
196
80 HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
1 No. 1 No. LLANDOW TRADING ESTATE,
NEAR COWBRIDGE
TOP VIEW TOP VIEW P15 VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
1 No.
60 10
UB 254x146x37 10 60
PFC 200x75x23 10 =155=
CLIENT
80 80 UB 254x146x37
C15
63
45
50
C15
91
35
45a
75
22 P12
(2 NOS.) PROJECT
234
P15
75
234
75
P12 22
BARRY - BIOMASS UK No 2 LLP
63
(1 NO.) P14
~10~
35
22 22
C15
91
TYP TO SUIT M20 TITLE
45a C15
10
TURBINE PLATFORM
FABRICATION DRAWING
SECTION E4-E4 SECTION E3-E3 ITEM NO.45a SECTION E6-E6 SECTION E5-E5 SCALE DRAWING SIZE DRAWN
1 No.
1:5 A1 ES/MU
TYPE 10 TYPE 11 DRAWING No. REV.
1 Location 1 Location XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
E8 NOTES
=80
GENERAL NOTES:
E7 E7 =
10
1. Do not scale from this drawing.
80x
EA
2. All dimensions are in millimetres(mm) and all levels are in
metres(m) AOD, unless noted otherwise.
F3 3. All Dimensions and levels to be checked on site and any
145
discrepancies should be reported to GHD LIVIGUNN.
UB 305x165x40
35 75 35
39 76
UB 254x146x37 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
40
40
specification (NSSS) Fifth Edition 2010, CE Marking Version.
88
155
P12
75
155
S355JR to BS EN 10025-2. All structural hollow sections to be
75
~10~ ~10~ 22
22 grade S355JRH to BS EN 10210-2.
64
UB 254x146x37
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
251
251
40
40
P16 ~10~ and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
22 22
F2 F2 22
TYP 4. Steel overhead runway beams shall be tested in accordance with
119
TYP TYP BS 1993-6 and BS 2853.
P17
22 5. All Connections forces shown are U.L.S. value.
F3 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
E8 183 104 bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
TOP VIEW P18 P17 TOP VIEW P19 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
1 No. 1 No. 3 Nos.
EN ISO 14713-1 and design life of 25 years. The surface protection
=145= classification shall be as follows conforming to the classes defined
10 70
=145= 10 60 in EN BS 12944:
UB 305x165x40 UB 254x146x37 - For any steel elements inside, not including insulated piping and
lagging: Class C3(Urban and Industrial atmosphere, moderate
C15 sulphur dioxide levels and production areas with the high humidity).
60
C15
91
91
- For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
22 plants).
P18 P16 P18 - For the outside steel elements, not including insulated piping and
~10~
234
75
75
(2 NOS.)
P19 lagging: Class C4(Industrial and Coastal chemical processing plants)
283
~10~ P19 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
P17 22 P12
(3 NOS.)
following structure which are defined as EXC3:
Runway Beam
90
22 C15 Brackets supporting runway beam
ON HOLD
138
60
70
~10~
95
REFERENCE DOCUMENTS:
49 107
97
- KEY PLAN - BARRY_01_DWG_23_20700
58
C15
60
226
136
22
22 TYP - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
x10
80
57
~10~
130
EA
PFC 200x75x23
P1
(1 NO.)
22 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
140
E9 E9 Plan El 10.400m
158
EA
P1 22
80
119
118
x10
TYP ~10~
C15 109 107 Plan El 10.400m
22
TO SUIT M20 - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
P20
Plan El 13.500
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
100
63
120 35 45
x10
158
80
22
TY 5
74 49
14
EA
TYP
CLIENT
75
35
255
PFC 200x75x23
57
=8
TY 0=
145
196
75
P
135
97
80
119
45
PROJECT
35
22
114 115
TYP 45 BARRY - BIOMASS UK No 2 LLP
TITLE
TOP VIEW SECTION F1-F1 P22 ITEM NO.45 TURBINE PLATFORM
2 Nos.
FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
1:5 A1 ES/MU
TYPE 13 DRAWING No. REV.
1 Location XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
F5
GENERAL NOTES:
80 80
P24 145 UB 254x146x37 1. Do not scale from this drawing.
35 45 2. All dimensions are in millimetres(mm) and all levels are in
35 75 35 =8 metres(m) AOD, unless noted otherwise.
63
UB 254x146x37 TY 0=
P23 P 3. All Dimensions and levels to be checked on site and any
x10
discrepancies should be reported to GHD LIVIGUNN.
80
35
EA
4. This drawing is to be read in conjunction with relevant project
75
40
PFC 200x75x23
TY 5
14
standards and specification.
145
75
5. Holes to be drilled through and fastened to plates
~10~
6. Pipe supports on hold.
155
75
22 P1
UB 305x165x40
35
119
45 STEELWORK:
40
22
TYP 45
22
1. All works are to be carried out in accordance with the
100
P25 recomendation of the of the national structural steelwork
TYP
F4 F4 specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
F5 UB 254x146x37 S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
108
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
TOP VIEW P24 SECTION F6-F6 ITEM NO.45 and Holding Down Bolts designed by client. Details to be confirmed
2 Nos. by civil contractor.
3 Nos. 4. Steel overhead runway beams shall be tested in accordance with
45
BS 1993-6 and BS 2853.
108
5. All Connections forces shown are U.L.S. value.
F6 F6 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
60 216
bolts
215
PFC 200x75x23
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
100
TYP
P26 102 114 92 123 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
70 9 =145= to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
UB 254x146x37 galvanised coating to be min 85m. Environment category C3 to BS
60
C15
22 ~10~
22 EN ISO 14713-1 and design life of 25 years. The surface protection
71
C15 P1 TYP 83 46
97
F6a F6a 22 classification shall be as follows conforming to the classes defined
157
91
P1
in EN BS 12944:
175
(2 NOS.) ~10~
P25,P26 - For any steel elements inside, not including insulated piping and
EA
22
57
249
80
140
234
lagging: Class C3(Urban and Industrial atmosphere, moderate
x10
59
~10~ P24 22 sulphur dioxide levels and production areas with the high humidity).
75
C15 83 49 TYP
P23 P24 22 - For the steel elements in the fuel storage, not including insulated
283
22
(3 NOS.) TO SUIT M20 and lagging: Class C4(Industrial and coastal chemical processing
93
~10~
70
plants).
- For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
138
100 116
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
C15 97 118 following structure which are defined as EXC3:
Runway Beam
10 22
TO SUIT M20
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
(Turbine building, workshop)
SECTION F4-F4 SECTION F5-F5 TOP VIEW SECTION F6a-F6a P25 P26 11. Allowance for levelling shims and grout thickness not to be less
1 No. 1 No. than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
TYPE 15 TYPE 16 13. Nominal grout thickness is 25mm u.n.o.
3 Locations 1 Location 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
150 150 BS 8300 Handrails
11
70 80
80 80 98 52 To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
17
45 35
C15 with HIT-V-R Rods, minimum 270mm embedent.
F7a F7 F7a 90
C15 16. Over material (O.M.) to be cut and cut out to be applied after final
PFC 200x75x23
UB 305x165x40
P129 UB 254x146x37
C15 22 chemical anchors.
245
145
234
146
75
~10~
P130 P130
G3 G3 ~10~
22
35
181
P128 P131
UB 254x146x37 (2 NOS.)
~10~ C15 REFERENCE DOCUMENTS:
45
C15 22
TYP
45
C15 C15
- KEY PLAN - BARRY_01_DWG_23_20700
P27 22 22 P27
17
C15
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
70 80 ~10~ ~10~
P133 - C & S REPORT (REP) - BARRY_01_20076
139
P128 ITEM NO.45 TYP
P28
2 Nos. -
-
C & S REPORT (REP) - BARRY_01_20077
BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
4 Nos. C15 C15
R4 R4 Plan El 10.400m
UB 305x165x40
145 6 Nos.
35 76 35 P133 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
65 146 Plan El 10.400m
P128
TYP C15
P12 P132 36 75 36 - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
63
PFC 200x75x23
P130 P130 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
22
Sections A, B, P, R
53
150
P129 22
PFC 200x75x23
~10~
75
~10~
C15 TOP VIEW TOP VIEW -
Sections C, D.
BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
75
UB 254x146x37
256
~10~
F7 55 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
75
22
22 Rev Date Description By Chk App
TYP
F8 F8 45 75 45
Revision
TOP VIEW
53
141 HARRIS PYE UK LIMITED,
TOP VIEW P129 10 60
P134
22
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
12 Nos. 33 75 33 UB 254x146x37 TYP
NEAR COWBRIDGE
P133
32
75 68 VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
77
C15 141
63
P129
95
33 75 33
75
75
CLIENT
22
220
220
75
P129 22
~10~ ~10~ P133
234
35
75
75
75
PROJECT
35
22
77
220
TO SUIT M20 22 C15 22
52
P129 ~10~
TO SUIT M20 22 P28
BARRY - BIOMASS UK No 2 LLP
75
P128 P128 45 TYP
35
TITLE
22 TURBINE PLATFORM
TYP
SECTION F7-F7 SECTION F7a-F7a SECTION F8-F8 SECTION G3-G3 P28 SECTION R4-R4 P28 FABRICATION DRAWING
1 No. 1 No.
SCALE DRAWING SIZE DRAWN
TYPE 17 TYPE 18 TYPE 21a TYPE 21b 1:5 A1 ES/MU
3 Locations 4 Locations 1 Location 1 Location DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
96
118
NOTES
G2
PFC 200x75x23
GENERAL NOTES:
EA
75 46 =8
0=
80
22
93
x10
0
127
x1
1. Do not scale from this drawing.
80
EA
2. All dimensions are in millimetres(mm) and all levels are in
P1
metres(m) AOD, unless noted otherwise.
59
5
255
110 108
14
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
162
P29 22 80 80
~10~
128
TYP standards and specification.
118
PFC 200x75x23
22 83 52 35 45 5. Holes to be drilled through and fastened to plates
104
100
UB 254x146x37 TO SUIT M20 6. Pipe supports on hold.
~10~
G1 G1
35
TYP P31
54
STEELWORK:
212
UB 254x146x37 22
145
P29
75
1. All works are to be carried out in accordance with the
108
108
P30
86
45a 22 recomendation of the of the national structural steelwork
45a 1 No. TYP specification (NSSS) Fifth Edition 2010, CE Marking Version.
35
248
2. All hot rolled general steelwork and base plates to be grade
F9 22
F9 22 S355JR to BS EN 10025-2. All structural hollow sections to be
P12 115 104 45a
TO SUIT M20 TYP grade S355JRH to BS EN 10210-2.
~10~ 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
108
73 52
by civil contractor.
151
22
10
TYP
G2 4. Steel overhead runway beams shall be tested in accordance with
x
80
TY 5
EA
14
254
5. All Connections forces shown are U.L.S. value.
54
1 No. 1 No. 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
PFC 200x75x23
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
146
bolts
104
=8 22
82
TY 0= 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
P
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
10 60
60 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
108 140
galvanised coating to be min 85m. Environment category C3 to BS
PFC 200x75x23 EN ISO 14713-1 and design life of 25 years. The surface protection
60
C15
63
1 No. - For any steel elements inside, not including insulated piping and
22
P1 lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
175
~10~
75
(1 NO.)
P31 45a ~10~
10 P12 - For the steel elements in the fuel storage, not including insulated
234
140
(1 NO.)
80 80 and lagging: Class C4(Industrial and coastal chemical processing
UB 254x146x37
plants).
63
C15
35 45 - For the outside steel elements, not including insulated piping and
63
35
following structure which are defined as EXC3:
75
75
Column supporting brackets
Horizontal TIE members
63
40
UB 254x146x37
C15 P6 P6
P1 22
75
P34 22 22
155
75
(2 NOS.)
~10~ P36 REFERENCE DOCUMENTS:
181
220
140
UB 254x146x37
75
UB 203x133x30
~10~
22 - C & S REPORT (REP) - BARRY_01_20076
C15
TYP - C & S REPORT (REP) - BARRY_01_20077
35
=145= =150=
HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
=135=
NEAR COWBRIDGE
P1 P35 P35 150 VALE OF GLAMORGAN, CF71 7PB
P1
UB 305x165x40 www.harrispye.com
30 90 30
53
58
91
35
CLIENT
75
P32
UC 203x203x46
UC 203x203x46
70
70
P36
75
210
75
70
70
PROJECT
91
P32 P35
35
P35
58
22
P1 TYP
22 22
P34 P1 TO SUIT M20 TYP
22 TITLE
TO SUIT M20
TURBINE PLATFORM
FABRICATION DRAWING
SECTION P4-P4 SECTION P5-P5 SECTION P6-P6 P36 SCALE DRAWING SIZE DRAWN
2 Nos.
TYPE 21 TYPE 22 1:5 A1 ES/MU
1 Location 1 Location DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
386
35 158 158 35
DO NOT SCALE - IF IN DOUBT ASK
NOTES
50
55
GENERAL NOTES:
22
1. Do not scale from this drawing.
100
2. All dimensions are in millimetres(mm) and all levels are in
93
175 ~10~
P7 C15
metres(m) AOD, unless noted otherwise.
305
102 73 139 3. All Dimensions and levels to be checked on site and any
50 52 P41d P41a discrepancies should be reported to GHD LIVIGUNN.
22
UB 254x146x37
P38a 4. This drawing is to be read in conjunction with relevant project
100
TYP 188
P38b P41b ~12~ standards and specification.
C15 G5 49
5. Holes to be drilled through and fastened to plates
P8 P8
35
6. Pipe supports on hold.
P41b
50
UB 254x146x37
22 8 Nos. STEELWORK:
70
22 ~10~
73
UC 203x203x71
TYP
236
210
22
C15 C15
P41a 93 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
70
2 Nos.
~10~ specification (NSSS) Fifth Edition 2010, CE Marking Version.
200 2. All hot rolled general steelwork and base plates to be grade
35
C15 S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
P37
and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
295
90 ~12~ 4. Steel overhead runway beams shall be tested in accordance with
200
P7
TYP
BS 1993-6 and BS 2853.
25
TOP VIEW ITEM NO.38a ITEM NO.38b TYP
~10~ 49
5. All Connections forces shown are U.L.S. value.
1 No. 1 Nos. 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
G5 ~8~
89
P41b bolts
22
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
33
P41d P41a 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
=150=
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
TOP VIEW P41c P41d P41e
UC 152x152x23
10
P38b and lagging: Class C4(Industrial and coastal chemical processing
plants).
P37 - For the outside steel elements, not including insulated piping and
=210=
100
P41b P41b 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
Runway Beam
206
22 P41b
Brackets supporting runway beam
Column supporting brackets ON HOLD
95
TO SUIT M20 P41b P41b Horizontal TIE members
Overhead crane supporting structures
P38b (Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
P41b than 15mm and no more than 25mm. May vary for large base plates.
89
12. Use non-shrink flowable grout fosroc conbextra GP or similar
SHSC 200x200x10
approved for grouting operatiions. The grout must extend between
SECTION P7-P7 TYPE 23 P41c P41c P41c
22
TO SUIT M20
120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
1 Location P41a 22 14. Access platforms, handrails, stairs, ladders shall conforming to:
P41a HOLES FOR PLUG WELDING BS 4952 Grating
P41e BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
SECTION G5-G5 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
TYPE 25 16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
275 2 Locations
17. - Indidacates area on base plate for drilling holes for
65 175 100 10 chemical anchors.
UC 152x152x23 UC 152x152x23
140 EXISTING
C15 C15 REFERENCE
22
P39 REFERENCE DOCUMENTS:
(4 NOS.)
- KEY PLAN - BARRY_01_DWG_23_20700
139
~10~
C15 C15
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
P40 - C & S REPORT (REP) - BARRY_01_20076
G4 C15 C15 G4 - C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
TYP
Plan El 10.400m
10d
277
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
22 22 P35 - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
(4 NOS.) Plan El 13.500
~10~ ~10~ - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
C15 C15 Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
TOP VIEW - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
UB 203x133x30 P42 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
G6 G6 Rev Date Description By Chk App
Revision
P35
30
166
56
33 100 33 CLIENT
100
40
~10~
40
P40
66
30
35
56
22
22 TYP P42
145
~10~
75
75
22
22 PROJECT
TO SUIT M20
35
P35
BARRY - BIOMASS UK No 2 LLP
66
22
TYP
TITLE
EXISTING
SECTION G4-G4 P40 REFERENCE TURBINE PLATFORM
2 Nos.
FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
SECTION G6-G6 P42
TYPE 26 TYPE 27 1 No.
1:5 A1 ES/MU
2 Locations 1 Location DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
GENERAL NOTES:
1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
H2 metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
G8
UB 203x133x30
PFC 200x75x23
45 35
5. Holes to be drilled through and fastened to plates
UB 203x133x30 141 6. Pipe supports on hold.
35
33 75 33
UB 203x133x30
STEELWORK:
145
75
35
1. All works are to be carried out in accordance with the
45a
recomendation of the of the national structural steelwork
35
specification (NSSS) Fifth Edition 2010, CE Marking Version.
145
P42 ~10~
75
22 2. All hot rolled general steelwork and base plates to be grade
22
TYP 45a
S355JR to BS EN 10025-2. All structural hollow sections to be
35
grade S355JRH to BS EN 10210-2.
G7 P43 G7 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
P42 and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
G8 H2 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
TOP VIEW P43 TOP VIEW ITEM NO.45a Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
1 No. 6 Nos.
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
55 10
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
=141= 10 55 galvanised coating to be min 85m. Environment category C3 to BS
UB 203x133x30
EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
C15 C15 in EN BS 12944:
63
66 22
- For any steel elements inside, not including insulated piping and
P42 22 P42 lagging: Class C3(Urban and Industrial atmosphere, moderate
(1 NO.) ~10~ (6 NOS.) sulphur dioxide levels and production areas with the high humidity).
75
188
188
45a
75
P43 P43 - For the steel elements in the fuel storage, not including insulated
~10~
and lagging: Class C4(Industrial and coastal chemical processing
plants).
63
66
C15 C15 - For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
10
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
SECTION G7-G7 SECTION G8-G8 SECTION H2-H2 (Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
TYPE 28 TYPE 30 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
1 Locations 6 Locations 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
=166= with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
H1 dimension check.
166 17. - Indidacates area on base plate for drilling holes for
chemical anchors.
77 85 141 33 100 33
10 H2 33 75 33
66
35
REFERENCE DOCUMENTS:
35
10
=15
80x
145 EA - KEY PLAN - BARRY_01_DWG_23_20700
0=
22
145
75
75
P44a
TO SUIT M20 ~10~
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
145
22
75
P45 - C & S REPORT (REP) - BARRY_01_20076
35
- C & S REPORT (REP) - BARRY_01_20077
UB 203x133x30
66
35
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
22 22 Plan El 10.400m
TO SUIT M20 22 TYP
TYP - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
P42 UB 203x133x30
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
EXISTING Plan El 13.500
REFERENCE - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
22
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
TO SUIT M20 Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
G9 P44 P42 G9 SECTION G9-G9 P44 P44a Hall Sections E, F, G
1 Nos. 1 Nos.
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
Rev Date Description By Chk App
C15 C15 H2 10 Revision
246 79
=141= HARRIS PYE UK LIMITED,
55
HANGER 5 & 6, BONA ROAD
UB 203x133x30 LLANDOW TRADING ESTATE,
22 22 64 66 NEAR COWBRIDGE
TYP
TYP
22
277
108
C15 VALE OF GLAMORGAN, CF71 7PB
128
60
66
~10~ www.harrispye.com
P42
~10~ P42 22
P42
39
(2 NOS.)
238
(4 NOS.)
188
P44
75
130
C15 C15 22
110
110
P44
P42 TYP
66
C15
140
TYP EXISTING 22
REFERENCE TO SUIT M20 185 140 PROJECT
325
TITLE
TOP VIEW SECTION H1-H1 SECTION H2-H2 P45 TURBINE PLATFORM
1 No.
FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
TYPE 29 1:5 A1 ES/MU
1 Location DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
100 96 50 100
NOTES
H4 214 GENERAL NOTES:
22
200
1. Do not scale from this drawing.
UB 203x133x30
2. All dimensions are in millimetres(mm) and all levels are in
P42 P42 P42
metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
~10~
C15 discrepancies should be reported to GHD LIVIGUNN.
64 73 4. This drawing is to be read in conjunction with relevant project
147
110
TYP 73 64 standards and specification.
192
163
22
TYP 5. Holes to be drilled through and fastened to plates
22
6. Pipe supports on hold.
238
275
P47 TYP
H3 145
H3 ~10~
39
45a
P STEELWORK:
39
TY
128
EA
128
80x
76
75
10
22 1. All works are to be carried out in accordance with the
83
76
0
80x1 recomendation of the of the national structural steelwork
EA
specification (NSSS) Fifth Edition 2010, CE Marking Version.
121 79 2. All hot rolled general steelwork and base plates to be grade
79 135 S355JR to BS EN 10025-2. All structural hollow sections to be
PFC 200x75x23
P46 grade S355JRH to BS EN 10210-2.
22 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
=80 P
TO SUIT M20
TY
by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
H4 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
TOP VIEW P46 P47 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
1 No. 1 No.
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
55 10 80 80 EN ISO 14713-1 and design life of 25 years. The surface protection
45 35
classification shall be as follows conforming to the classes defined
UB 203x133x30 in EN BS 12944:
- For any steel elements inside, not including insulated piping and
C15
35
lagging: Class C3(Urban and Industrial atmosphere, moderate
63
63
sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
145
75
22
and lagging: Class C4(Industrial and coastal chemical processing
75
75
188
P46 P47 42
~10~ plants).
(3 NOS.) 45a
35
45a - For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
69
69
C15 22
TYP
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
45a
following structure which are defined as EXC3:
Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
SECTION H3-H3 SECTION H4-H4 ITEM NO.45a (Turbine building, workshop)
1 No. 11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
TYPE 31 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
1 Location 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
H5 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
292 292 dimension check.
145 17. - Indidacates area on base plate for drilling holes for
PFC 200x75x23
TY 22
TY =
P
P
EA TO SUIT M 20
80x 10
10 80x
EA
64 66
P48 P49 66 64 REFERENCE DOCUMENTS:
128
132
128
- KEY PLAN - BARRY_01_DWG_23_20700
132
45a
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
H5a H5a
39
39
238
238
UB 203x133x30
- C & S REPORT (REP) - BARRY_01_20077
22 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
22
110
110
~10~
106
Plan El 10.400m
110
110
106
TYP TYP ~10~
TYP - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
22 22 Plan El 13.500
292 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
P42 P42 P42 292 Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
100 110 110 100 Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
H5
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
TOP VIEW P48 P49 Rev Date Description By Chk App
1 No. 1 No.
Revision
35
CLIENT
28
C15
145
63
75
35
145
75
C15
BARRY - BIOMASS UK No 2 LLP
34
22
TO SIT M20
TITLE
TURBINE PLATFORM
SECTION H5a-H5a SECTION H5-H5 ITEM NO.45a FABRICATION DRAWING
1 No.
SCALE DRAWING SIZE DRAWN
TYPE 32 1:5 A1 ES/MU
1 Location DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
H6 DO NOT SCALE - IF IN DOUBT ASK
NOTES
75 70
P42 P50 GENERAL NOTES:
UB 203x133x30 UB 203x133x30
1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
metres(m) AOD, unless noted otherwise.
150
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
142 100 4. This drawing is to be read in conjunction with relevant project
133 standards and specification.
P51 22 5. Holes to be drilled through and fastened to plates
120
P52 145 29 75 29 6. Pipe supports on hold.
60
~10~ 30 60 30
145
P
TY
H8 H8
184
P53
73 64 22 111 44 STEELWORK:
35
35
22
75
273
139
10 22
150
80x
TYP 1. All works are to be carried out in accordance with the
EA TYP
recomendation of the of the national structural steelwork
145
145
75
75
22 ~10~ 22 ~10~ 22
39
TYP specification (NSSS) Fifth Edition 2010, CE Marking Version.
61
128
~10~ 2. All hot rolled general steelwork and base plates to be grade
35
35
89
H7 H7 S355JR to BS EN 10025-2. All structural hollow sections to be
76
=15 P
88
TY
76
22
68
22
EA
P42 TYP TYP 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
80
x10
and Holding Down Bolts designed by client. Details to be confirmed
UB 203x133x30
120 122 by civil contractor.
79 144 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
223 242
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
H6 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
TOP VIEW P52 P53 P51 P50 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
1 No. 1 No. 1 No. 1 No. to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
55 EN ISO 14713-1 and design life of 25 years. The surface protection
=120= classification shall be as follows conforming to the classes defined
P52 =133=
in EN BS 12944:
UB 203x133x30 UB 203x133x30 UB 203x133x30 - For any steel elements inside, not including insulated piping and
C15 lagging: Class C3(Urban and Industrial atmosphere, moderate
60
66
66
sulphur dioxide levels and production areas with the high humidity).
UB 152x152x37
P42 22 - For the steel elements in the fuel storage, not including insulated
(2 NOS.) and lagging: Class C4(Industrial and coastal chemical processing
188
75
75
P52 P53 P51 plants).
P42 ~10~ - For the outside steel elements, not including insulated piping and
147
66
C15
following structure which are defined as EXC3:
Runway Beam
P50 22
TO SUIT M20
22
TO SUIT M20
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
SECTION H6-H6 SECTION H7-H7 SECTION H8-H8 12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
TYPE 33 13. Nominal grout thickness is 25mm u.n.o.
1 Location 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
P54 J1 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
UB 203x133x30
dimension check.
J2 17. - Indidacates area on base plate for drilling holes for
35 chemical anchors.
UB 203x133x30 UB 203x133x30
39
80
80
35 P56
REFERENCE DOCUMENTS:
EA
0
x1
80
35
80
- KEY PLAN - BARRY_01_DWG_23_20700
x10
EA
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
- C & S REPORT (REP) - BARRY_01_20076
H9 P55 H9 - C & S REPORT (REP) - BARRY_01_20077
141 22 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
TO SUIT M20
141 33 75 33 Plan El 10.400m
33 75 33 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
C15 C15
Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
35
35
EXISTING UB 203x133x30
REFERENCE
Plan El 13.500
~10~ - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
145
145
~10~
75
75
22 22 Sections A, B, P, R
TYP
TYP
Sections C, D.
35
35
88
115
UB 203x133x30 22
P35 P35 TYP
C15
60
66
66
61
50
P35 ~10~
249
P42 22 PROJECT
(1 NO.)
161
188
75
134
P55 P54 76 44 56 71
~10~ P56
112
111
147
P55
EXISTING
REFERENCE P35
66
66
C15 TITLE
P35 P35
22
589
TURBINE PLATFORM
TYP
22
TO SUIT M20
FABRICATION DRAWING
EXISTING
REFERENCE
SCALE DRAWING SIZE DRAWN
SECTION H9-H9 SECTION J1-J1 SECTION J2-J2 P56 1:5 A1 ES/MU
141
56
81
22 STEELWORK:
223
22
TYP 22
63
TO SUIT M20 22 ~10~
TYP TYP 1. All works are to be carried out in accordance with the
202
50
10 ~10~ recomendation of the of the national structural steelwork
82
x
80 specification (NSSS) Fifth Edition 2010, CE Marking Version.
66
EA
112
P58 2. All hot rolled general steelwork and base plates to be grade
J4
74
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
PFC 200x75x23
69 126
and Holding Down Bolts designed by client. Details to be confirmed
=8 P
0=
TY
60
63
sulphur dioxide levels and production areas with the high humidity).
35
P42 - For the steel elements in the fuel storage, not including insulated
(1 NO.) and lagging: Class C4(Industrial and coastal chemical processing
=145=
75
188
plants).
145
75
45a
~10~ - For the outside steel elements, not including insulated piping and
140
45a P57
lagging: Class C4(Industrial and Coastal chemical processing plants)
35
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
63
C15
following structure which are defined as EXC3:
22
TYP Runway Beam
10 22
TO SUIT M20
45a
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
SECTION J3-J3 SECTION J4-J4 ITEM NO.45a 12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
1 No.
120mm and 50mm past the base plates edges.
TYPE 36 13. Nominal grout thickness is 25mm u.n.o.
1 Location 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
J6 240 17. - Indidacates area on base plate for drilling holes for
chemical anchors.
126 114
=
=80 P
TY 220
EA
80x
REFERENCE DOCUMENTS:
10
76 41 99
J7
82
PFC 200x75x23
22 0
TY
x1
TO SUIT M20 80 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
P
EA
175
56 71
22 - C & S REPORT (REP) - BARRY_01_20076
63
106
113
TYP P61 - C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
UB 203x133x30 UB 203x133x30
Plan El 10.400m
49
P59
246
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
230
~10~
P60 Plan El 10.400m
175
133
137
Plan El 13.500
112
UB 203x133x30 TYP
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
45a
TYP - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
22 22 Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
P42 P42 P42 240 Hall Sections E, F, G
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
J7
Rev Date Description By Chk App
J6 Revision
100 50 110 100 HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
TOP VIEW P59 P60 TOP VIEW NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
1 No. 1 No. www.harrispye.com
=120=
CLIENT
120
55 10 80 80
30 60 30
UB 203x133x30 PFC 200x75x23 45 35
35
C15 P61
63
35
PROJECT
=145=
UB 152x152x37
P42
145
~10~
75
(3 NOS.)
BARRY - BIOMASS UK No 2 LLP
145
75
=145=
75
188
35
35
22 22
TITLE
63
TO SUIT M20
C15 22
TYP 45a TURBINE PLATFORM
22
10
TO SUIT M20 FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
SECTION J5-J5 SECTION J6-J6 ITEM NO.45a SECTION J7-J7 P61 1:5 A1 ES/MU
TYPE 37 1 No.
TYPE 38 2 Nos.
DRAWING No. REV.
1 Location 1 Location XXX-XXX-XXX-XXX-XXX A0
166 120 DO NOT SCALE - IF IN DOUBT ASK
J9 K1 33 100 33 30 60 30
NOTES
UB 203x133x30
35
P66
35
P42
GENERAL NOTES:
145
UB 203x133x30 UB 203x133x30 UB 203x133x30
75
249 ~10~ ~10~
145
75
1. Do not scale from this drawing.
123 126
138 111
2. All dimensions are in millimetres(mm) and all levels are in
22 22
35
metres(m) AOD, unless noted otherwise.
35
3. All Dimensions and levels to be checked on site and any
22 discrepancies should be reported to GHD LIVIGUNN.
59 TYP 22
P62 TYP 4. This drawing is to be read in conjunction with relevant project
87
22
K2 K2 standards and specification.
108
5 80 56 TYP P67
22
J8 14 P
TY
J8 TYP P67 P65 5. Holes to be drilled through and fastened to plates
205
6. Pipe supports on hold.
47
22
~10~
221
22 1 No. 1 No.
C15
49
TOP SUIT M20
118
15 141
STEELWORK:
75
113
~10~ 22
P65 1. All works are to be carried out in accordance with the
74
EA 33 75 33
UB 203x133x30
80 UB 203x133x30
x10 x1
0
recomendation of the of the national structural steelwork
80 156 93 ~10~
EA specification (NSSS) Fifth Edition 2010, CE Marking Version.
35
277
P35 22
2. All hot rolled general steelwork and base plates to be grade
99 150
(2 NOS.)
S355JR to BS EN 10025-2. All structural hollow sections to be
145
grade S355JRH to BS EN 10210-2.
75
~10~
249 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
=1 YP
22
50
P64
T
P63
35
C15 by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
J9 22
TYP
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
140 K1 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
EXISTING REFERENCE
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
TOP VIEW P63 P64 TOP VIEW P66 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
1 No. 1 No. 2 Nos. to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
10 =141= galvanised coating to be min 85m. Environment category C3 to BS
=166=
55 10 EN ISO 14713-1 and design life of 25 years. The surface protection
=166= =120= classification shall be as follows conforming to the classes defined
166 P35 in EN BS 12944:
UB 203x133x30 UB 203x133x30 33 100 33 UB 203x133x30 - For any steel elements inside, not including insulated piping and
P35
C15 lagging: Class C3(Urban and Industrial atmosphere, moderate
66
66
66
66
sulphur dioxide levels and production areas with the high humidity).
35
P42 P65 - For the steel elements in the fuel storage, not including insulated
22
(1 NO.)
P67
and lagging: Class C4(Industrial and coastal chemical processing
P63
145
188
P62
75
75
75
75
75
~10~ 22 plants).
~10~ P67
P62 TO SUIT M20 - For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
35
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
66
66
66
66
C15
22 following structure which are defined as EXC3:
22 P35
TYP Runway Beam
22
TO SUIT M20
P35 P66
EXISTING REFERENCE
22
TO SUIT M20
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
EXISTING REFERENCE (Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
SECTION J8-J8 SECTION J9-J9 P62 SECTION K1-K1 SECTION K2-K2 12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
1 No.
120mm and 50mm past the base plates edges.
TYPE 39 TYPE 40 13. Nominal grout thickness is 25mm u.n.o.
1 Location 1 Location 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
K3 dimension check.
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
PFC 200x75x23
302
22
TY =
0
=8
P
127
45a - C & S REPORT (REP) - BARRY_01_20076
22 64 66
- C & S REPORT (REP) - BARRY_01_20077
127
139
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
47
P69
244
40
UB 203x133x30 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
22 Plan El 10.400m
126
117
TYP
111
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
~10~
110
111
Plan El 13.500
99
22
TYP - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
P42 P42 P42 Sections A, B, P, R
22 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
302 Sections C, D.
253 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
100 96 97 100
Hall Sections E, F, G
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
K3 Rev Date Description By Chk App
Revision
10 55 CLIENT
80 80
C15
63
35
22 P42
(3 NOS.)
PROJECT
=145=
145
75
75
188
35
63
C15 22
TYP
TITLE
45a
22 10 TURBINE PLATFORM
TO SUIT M20
FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
SECTION K2-K2 SECTION K3-K3 ITEM NO.45a 1:5 A1 ES/MU
TYPE 41 1 No.
DRAWING No. REV.
1 Location XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
GENERAL NOTES:
1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
297
metres(m) AOD, unless noted otherwise.
P142 R7 222 3. All Dimensions and levels to be checked on site and any
P141 120 177 discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
UB 203x133x30 P136 standards and specification.
140 5. Holes to be drilled through and fastened to plates
P139 P73 6. Pipe supports on hold.
35 70 35
82
110 ~10~
STEELWORK:
120
P74 68 67 29 64 22
146
50
73 64
184
1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
64
CHS TYP
140
273
145
294
160
88.9
specification (NSSS) Fifth Edition 2010, CE Marking Version.
75
x5 ~10~
74
R TYP
64
P140 2. All hot rolled general steelwork and base plates to be grade
191
TYP
29
~10~
40
S355JR to BS EN 10025-2. All structural hollow sections to be
35
grade S355JRH to BS EN 10210-2.
127
10 64
0=
80x 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
=1 4
89
EA
100
76
22 ~10~ 22
22 and Holding Down Bolts designed by client. Details to be confirmed
UB 203x133x30
TYP 22
by civil contractor.
21
22 4. Steel overhead runway beams shall be tested in accordance with
TO SUIT M20 BS 1993-6 and BS 2853.
80
P138 80 142
P137
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
P73 P74 P136 P137 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
1 No. 1 No. 1 No. 1 No.
R6 R7 R6
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
175
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
102 73 73 to be 4mm fillet welds.
120 120 133
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
TOP VIEW
16
30 60 30 30 60 30 29 75 29 50 52 galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
C15 classification shall be as follows conforming to the classes defined
35
35
35
C15
P142 22 ~10~ ~10~ in EN BS 12944:
- For any steel elements inside, not including insulated piping and
139
145
145
145
75
75
75
~10~ 22 ~10~ 22 ~10~ 22 22 lagging: Class C3(Urban and Industrial atmosphere, moderate
155
P141 TYP sulphur dioxide levels and production areas with the high humidity).
UB 203x133x30 UB 203x133x30 C15 - For the steel elements in the fuel storage, not including insulated
35
35
35
22 and lagging: Class C4(Industrial and coastal chemical processing
C15
60
16
P138 lagging: Class C4(Industrial and Coastal chemical processing plants)
P137
P140 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
P138 P139 P140 P141 P142 Runway Beam
P136
1 No. 1 No. 1 No. 1 No. 2 Nos. Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
P136 P136
UC 152x152x23
UC 152x152x23
UC 152x152x23
P142 (Turbine building, workshop)
TYPE 42 11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
1 Location
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
SECTION R6-R6 SECTION R7-R7 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
30
K6 K5 To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
140 with HIT-V-R Rods, minimum 270mm embedent.
87 281
16. Over material (O.M.) to be cut and cut out to be applied after final
0=
CHS
88.9 dimension check.
=14
K4 x5
P72 17. - Indidacates area on base plate for drilling holes for
chemical anchors.
140 22
TYP 64
UB 203x133x30
116
22
160
REFERENCE DOCUMENTS:
29
191
55 70 35 - KEY PLAN - BARRY_01_DWG_23_20700
64
P74
C15 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
64
316
P73 - C & S REPORT (REP) - BARRY_01_20076
35
UB 203x133x30 - C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
UB 203x133x30
~10~
200
P70 22 29 35 29
Plan El 10.400m
140
70
~10~
145
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
125
277
~10~ P35 Plan El 10.400m
K4
35
(4 NOS.)
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
22
TYP
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
P42 P71 Sections A, B, P, R
TOP VIEW C15 18 350 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
368 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
150 166
Hall Sections E, F, G
EXISTING REFERENCE A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
K6 K5 Rev Date Description By Chk App
TOP VIEW P72 P73 Revision
1 No. 1 No.
HARRIS PYE UK LIMITED,
=141= 141 HANGER 5 & 6, BONA ROAD
=120=
UB 203x133x30 LLANDOW TRADING ESTATE,
33 75 33 NEAR COWBRIDGE
55 120 VALE OF GLAMORGAN, CF71 7PB
110
66
www.harrispye.com
35
30 60 30
~10~ C15
145
66
75
75
P70
35
103
CLIENT
~10~ P42
~10~
35
(1 NO.)
145
188
75
75
P71 ~10~
66
140
22 22
22 22
TYP 22
P72
35
66
22
TO SUIT M20
BARRY - BIOMASS UK No 2 LLP
SECTION K4-K4 P70
2 Nos.
TITLE
EXISTING REFERENCE
TURBINE PLATFORM
FABRICATION DRAWING
SECTION K5-K5 SECTION K6-K6 P74 P71 SCALE DRAWING SIZE DRAWN
TYPE 43 TYPE 44 1 No. 1 No. 1:5 A1 ES/MU
2 Locations 1 Location
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
K7 K9 L1
(4 NOS.)
GENERAL NOTES:
EXISTING REFERENCE
140 P35
EXISTING REFERENCE
1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
P77
metres(m) AOD, unless noted otherwise.
C15 UB 254x102x28 3. All Dimensions and levels to be checked on site and any
~10~ 145
UB 254x102x28 22 discrepancies should be reported to GHD LIVIGUNN.
135 35 75 35 4. This drawing is to be read in conjunction with relevant project
UB 254x102x28
30 75 30 C15 C15 standards and specification.
5. Holes to be drilled through and fastened to plates
35
C15 C15 6. Pipe supports on hold.
277
40
P35 P76
STEELWORK:
UB 254x102x28
~10~
130
75
(2 NOS.) 22 ~10~
~10~
K8 K8
160
80
220
1. All works are to be carried out in accordance with the
P78
P75 recomendation of the of the national structural steelwork
75
C15 specification (NSSS) Fifth Edition 2010, CE Marking Version.
40
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
35
277
grade S355JRH to BS EN 10210-2.
K9 TYP 22
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
TYP
L1 and Holding Down Bolts designed by client. Details to be confirmed
K7 by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
TOP VIEW TOP VIEW P76 TOP VIEW P78 5. All Connections forces shown are U.L.S. value.
2 Nos. 1 No. 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
=145= 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
=141=
EXISTING REFERENCE EXISTING REFERENCE to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
=135= 40 10
141 galvanised coating to be min 85m. Environment category C3 to BS
P35 EN ISO 14713-1 and design life of 25 years. The surface protection
33 75 33 UB 254x102x28 classification shall be as follows conforming to the classes defined
in EN BS 12944:
C15
55
55
- For any steel elements inside, not including insulated piping and
35
P35
90
lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
75
75
75
- For the steel elements in the fuel storage, not including insulated
P76 and lagging: Class C4(Industrial and coastal chemical processing
240
220
80
~10~ P77 ~10~ P76 78
(2 NOS.)
plants).
P75 - For the outside steel elements, not including insulated piping and
75
75
75
22 lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
90
22
35
55
TO SUIT M20 C15
Runway Beam
P35
22
TYP Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
TO SUIT M20
P35 Overhead crane supporting structures
22
TO SUIT M20 (Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
SECTION K7-K7 P75 SECTION K8-K8 SECTION K9-K9 SECTION L1-L1 12. Use non-shrink flowable grout fosroc conbextra GP or similar
1 No. approved for grouting operatiions. The grout must extend between
TYPE 45a TYPE 46 TYPE 47 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
1 Location 2 Locations 1 Location
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
L4 REFERENCE DOCUMENTS:
P79
- KEY PLAN - BARRY_01_DWG_23_20700
45a - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
80 80
P77 80 80 80 80 - C & S REPORT (REP) - BARRY_01_20076
PFC 200x75x23 PFC 200x75x23
45 35 45 35 45 35
PFC 200x75x23 - C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
UB 254x102x28
35
35
35
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
UB 356x171x45
Plan El 10.400m
145
145
145
75
75
75
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
45
PFC 200x90x30
Plan El 13.500
45a - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
35
35
35
L2 L2 L3 L3 Sections A, B, P, R
22 22 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
TYP 45a TYP 45a TYP 45a
Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
L4 Rev Date Description By Chk App
TOP VIEW ITEM NO.45a TOP VIEW ITEM NO.45a TOP VIEW ITEM NO.45a Revision
5 Nos. 4 Nos. 1 No.
HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
75 10 NEAR COWBRIDGE
17 10 VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
40 10
C15
63
63
PFC 200x75x23
C15 CLIENT
63
45a
75
75
45a
45a P79
75
63
63
332
P77
22 PROJECT
(5 NOS.)
22
63
22
TO SUIT M20 BARRY - BIOMASS UK No 2 LLP
10 TO SUIT M20
C15
TO SUIT M20
10 C15 TITLE
TURBINE PLATFORM
FABRICATION DRAWING
SECTION L2-L2 SECTION L3-L3 SECTION L4-L4 SCALE DRAWING SIZE DRAWN
TYPE 48 TYPE 49 TYPE 50 1:5 A1 ES/MU
5 Locations 4 Locations 1 Location
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
L6 DO NOT SCALE - IF IN DOUBT ASK
NOTES
GENERAL NOTES:
P79 P81
376
L7 1. Do not scale from this drawing.
UB 356x171x45
2. All dimensions are in millimetres(mm) and all levels are in
247 129
metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
135
PFC 200x90x30
135 135
L5 L5
88
62 75 standards and specification.
22 45 60 30 45 60 30
22 TYP 5. Holes to be drilled through and fastened to plates
TO SUIT M20 6. Pipe supports on hold.
212
22
42
P79 ~10~ PFC 200x75x23 PFC 200x75x23
90
40
40
STEELWORK:
124
EA
80
x10
76
150
150
70
70
~10~ ~10~ 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
UB 356x171x45
40
40
2. All hot rolled general steelwork and base plates to be grade
291 85 S355JR to BS EN 10025-2. All structural hollow sections to be
22 22 grade S355JRH to BS EN 10210-2.
P81
TYP 22 L6 L6 TYP 22
TY =
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
0
=8
P
P80
and Holding Down Bolts designed by client. Details to be confirmed
L6 L7 by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
TOP VIEW P80 P81 TOP VIEW P81 5. All Connections forces shown are U.L.S. value.
1 No. 1 No. 2 Nos. 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
P81
bolts
75 10 125 10 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
UB 356x171x45 UB 356x171x45 to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
28
C15 10 10
60
10 125 galvanised coating to be min 85m. Environment category C3 to BS
65
EN ISO 14713-1 and design life of 25 years. The surface protection
PFC 200x75x23 PFC 200x75x23 PFC 200x90x30 classification shall be as follows conforming to the classes defined
in EN BS 12944:
145
70
P80
65
- For any steel elements inside, not including insulated piping and
140
lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
332
P81 P81
70
P81 - For the steel elements in the fuel storage, not including insulated
28
~10~
P79 and lagging: Class C4(Industrial and coastal chemical processing
(2 NOS.) 22 plants).
216
65
- For the outside steel elements, not including insulated piping and
10 lagging: Class C4(Industrial and Coastal chemical processing plants)
22 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
TYP following structure which are defined as EXC3:
C15
Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
SECTION L5-L5 SECTION L6-L6 SECTION L6-L6 SECTION L7-L7 12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
TYPE 51 TYPE 52 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
1 Location 1 Location
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
193 118 BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
190 To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
L8 56 79 82 108 with HIT-V-R Rods, minimum 270mm embedent.
Q8
106
22 170 16. Over material (O.M.) to be cut and cut out to be applied after final
TYP dimension check.
10
48 75 48 17. - Indidacates area on base plate for drilling holes for
217
P81
chemical anchors.
50
~10~
UB 356x171x45
C15
22
112
PFC 200x75x23 PFC 200x75x23
75
UB 356x171x45
86
70 REFERENCE DOCUMENTS:
- KEY PLAN - BARRY_01_DWG_23_20700
135
90
~10~
332
351
311 - C & S REPORT (REP) - BARRY_01_20077
14
TY 5 ~10~ 22 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
P83
351
P P135
Plan El 10.400m
190
22
1 No.
22
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
90
395 Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
TYP P134 P133 C15 Plan El 13.500
EA
80
x10
EA
80
131 264 Q7 Q7 C15 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
22
86
x1 Sections A, B, P, R
0
TYP
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
10
74 63
Q8 Sections C, D.
=80 P
83
22 Hall Sections E, F, G
22 TYP
P82 L8 P83 TO SUIT M22 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
210
210
40
36
C15
60
65
P82
270
332
~10~
P79 P120
40
P81
200
22
150
P134
70
C15
46
22 TITLE
TO SUIT M20 22 P134 P134
TYP 22 TURBINE PLATFORM
FABRICATION DRAWING
SECTION L8-L8 P81 SECTION Q7-Q7 SECTION Q8-Q8 SCALE DRAWING SIZE DRAWN
TYPE 53 2 Nos. TYPE 54 1:5 A1 ES/MU
1 Location 1 Location
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
104
NOTES
220 81 C15
85 207 GENERAL NOTES:
1. Do not scale from this drawing.
~10~ 2. All dimensions are in millimetres(mm) and all levels are in
metres(m) AOD, unless noted otherwise.
160 79 67 62 22 63 66 3. All Dimensions and levels to be checked on site and any
124
142
22
M1a M1a discrepancies should be reported to GHD LIVIGUNN.
127
287
140
33 124 4. This drawing is to be read in conjunction with relevant project
42
352
352
standards and specification.
40
259
PFC 200x90x30
TY =
257
0
22
=8
14
P
22
EA TY 5 TO SUIT M20 80
x10
TYP 6. Pipe supports on hold.
80
x10 P EA ~10~ 22 22
135
129
~10~ TYP
68
117
TYP
STEELWORK:
130
129
117
P87
P86 1. All works are to be carried out in accordance with the
65
63
=160= recomendation of the of the national structural steelwork
M1 10
M1 22
specification (NSSS) Fifth Edition 2010, CE Marking Version.
300 2. All hot rolled general steelwork and base plates to be grade
292 135 108
UB 356x171x45
S355JR to BS EN 10025-2. All structural hollow sections to be
243 grade S355JRH to BS EN 10210-2.
150 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
150
and Holding Down Bolts designed by client. Details to be confirmed
P86 P87 P88 by civil contractor.
=152=
1 No. 1 No. 1 No. 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
P85 10 (NEAR SIDE) 135 (NEAR SIDE) 5. All Connections forces shown are U.L.S. value.
P84
17 (FAR SIDE) 128 (FAR SIDE) 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
17
bolts
P79 P79 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
M1a M1a 75 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
P85 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
429
P87 galvanised coating to be min 85m. Environment category C3 to BS
P88 EN ISO 14713-1 and design life of 25 years. The surface protection
C15 classification shall be as follows conforming to the classes defined
60
65
in EN BS 12944:
145 - For any steel elements inside, not including insulated piping and
160 lagging: Class C3(Urban and Industrial atmosphere, moderate
70
P86 P86 P87 30 60 55 sulphur dioxide levels and production areas with the high humidity).
P79 35 90 35 - For the steel elements in the fuel storage, not including insulated
P84
and lagging: Class C4(Industrial and coastal chemical processing
10
~10~
80x
(2 NOS.)
332
plants).
EA
22
40
35
- For the outside steel elements, not including insulated piping and
291
lagging: Class C4(Industrial and Coastal chemical processing plants)
PFC 200x75x23
22
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
150
216
TO SUIT M20
70
~10~
152
82
~10~
following structure which are defined as EXC3:
Runway Beam
ON HOLD
40
Brackets supporting runway beam
35
C15 Column supporting brackets
22 22 Horizontal TIE members
TYP TYP
Overhead crane supporting structures
(Turbine building, workshop)
TOP VIEW SECTION M1-M1 SECTION M1a-M1a P84 P85 11. Allowance for levelling shims and grout thickness not to be less
2 Nos. 1 No. than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
TYPE 55 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
1 Location
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
78 To steelway or approved equivalent supplier.
0=
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
=8
TO SUIT M20
17. - Indidacates area on base plate for drilling holes for
UB 254x102x28
100 169
chemical anchors.
M3 M3
UB 356x171x45
P89
175 160 M4 M4
44
35 105 35 35 90 35 P91
22
22 REFERENCE DOCUMENTS:
112
UB 356x171x45 TYP - KEY PLAN - BARRY_01_DWG_23_20700
152
82
50
135 - C & S REPORT (REP) - BARRY_01_20076
264
P90 - C & S REPORT (REP) - BARRY_01_20077
30 75 30
152
44
~10~
82
160
~10~
73 56 ~10~ Plan El 10.400m
153
40
131
M2 M2 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
113
P79
35
40
PFC 200x75x23
Plan El 10.400m
22
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
160
80
~10~
22 60 10 Plan El 13.500
22 TYP 22 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
120 150
Sections A, B, P, R
UB 356x171x45
M3 M3
40
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
22 Sections C, D.
TYP - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
TOP VIEW P89 P90 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
2 Nos. 1 No. Rev Date Description By Chk App
105 70
TOP VIEW P91 P93 Revision
2 Nos. 1 No.
HARRIS PYE UK LIMITED,
P90
106 69 HANGER 5 & 6, BONA ROAD
=135= 10 LLANDOW TRADING ESTATE,
P79 =135= NEAR COWBRIDGE
UB 356x171x45
(1 NOS.) VALE OF GLAMORGAN, CF71 7PB
UB 356x171x45 UB 356x171x45 www.harrispye.com
60
60
90
90
80
80
CLIENT
P93
22
80
80
22
TO SUIT M20 TO SUIT M20
22
TO SUIT M20 PROJECT
22
P89
211
211
181
TITLE
TURBINE PLATFORM
FABRICATION DRAWING
SECTION M2-M2 SECTION M3-M3 SECTION M3-M3 SECTION M4-M4 SCALE DRAWING SIZE DRAWN
TYPE 56 TYPE 57 1:5 A1 ES/MU
1 Location 1 Location
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
249
75 10 NOTES
114 135
R5 277
TYP PFC 200x75x23
250 GENERAL NOTES:
33 76
C15 154 95
1. Do not scale from this drawing.
63
(4 NOS.)
EXISTING REFERENCE
67
P35 =80 2. All dimensions are in millimetres(mm) and all levels are in
M5 =
22 metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
75
68
135 45a
UB 356x171x45 discrepancies should be reported to GHD LIVIGUNN.
250
30 75 30 ~10~
4. This drawing is to be read in conjunction with relevant project
TYP
130
~10~
22 standards and specification.
0
140 34
1
22
80x
63
332
5. Holes to be drilled through and fastened to plates
40
TYP
EA
C15 C15 ~10~ ~10~
257
P79 6. Pipe supports on hold.
~10~ (3 NOS.)
22 22 22
67
160
80
C15 C15
22
TO SUIT M20 22 TYP STEELWORK:
145
TYP
22 ~10~ 1. All works are to be carried out in accordance with the
68
40
160 89
recomendation of the of the national structural steelwork
C15
P132 P94 specification (NSSS) Fifth Edition 2010, CE Marking Version.
22 2. All hot rolled general steelwork and base plates to be grade
TYP
116 134
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
100
P79 22 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
TO SUIT M20 and Holding Down Bolts designed by client. Details to be confirmed
TOP VIEW P132 SECTION M6-M6 P94 P95 by civil contractor.
R5
35
1 No. PFC 200x75x23 1 No. 1 No. 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
96
P79 45a
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
EXISTING REFERENCE M6 M6 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
100
to be 4mm fillet welds.
UB 356x171x45
80 80 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
96
P95
55
45 35 EN ISO 14713-1 and design life of 25 years. The surface protection
UB 356x171x45
classification shall be as follows conforming to the classes defined
P79 in EN BS 12944:
35
=145=
- For any steel elements inside, not including insulated piping and
P95 P94
45a lagging: Class C3(Urban and Industrial atmosphere, moderate
145
75
sulphur dioxide levels and production areas with the high humidity).
160
P132
EA
- For the steel elements in the fuel storage, not including insulated
80x
10
and lagging: Class C4(Industrial and coastal chemical processing
35
291
plants).
22 - For the outside steel elements, not including insulated piping and
45a
TYP lagging: Class C4(Industrial and Coastal chemical processing plants)
P79 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
96
62
67
17. - Indidacates area on base plate for drilling holes for
106 220 chemical anchors.
UB 356x171x45
=
PFC 200x75x23
=80
67
TYP 22
EA
80x
346
346
22
89 34 TYP 82 55 - KEY PLAN - BARRY_01_DWG_23_20700
99
22 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
279
TYP
45a P79 - C & S REPORT (REP) - BARRY_01_20076
209
~10~ - C & S REPORT (REP) - BARRY_01_20077
51
~10~
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
22
Plan El 10.400m
110
M7 M7 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
74
145
Plan El 10.400m
TYP
80 80 NEAR COWBRIDGE
35
VALE OF GLAMORGAN, CF71 7PB
45 35 www.harrispye.com
75
=145=
45a
145
75
45a
35
P97
140
63
PFC 200x75x23
332
CLIENT
35
~10~
145
75
0
x1
80 22
22 EA 45a
TO SUIT M20 22 P79 TYP
35
(5 NOS.)
22 PROJECT
45a P97
TYP
C15
22
TO SUIT M20 BARRY - BIOMASS UK No 2 LLP
TITLE
TURBINE PLATFORM
SECTION M7-M7 ITEM NO.45a TOP VIEW SECTION M8-M8 ITEM NO.45a FABRICATION DRAWING
5 Nos. 2 Nos.
SCALE DRAWING SIZE DRAWN
TYPE 60 TYPE 61 1:5 A1 ES/MU
5 Location 1 Location DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
N4 DO NOT SCALE - IF IN DOUBT ASK
NOTES
347 284
GENERAL NOTES:
80 80 245 102 189 95 1. Do not scale from this drawing.
=8 P
0=
N1
TY
45 35 22 2. All dimensions are in millimetres(mm) and all levels are in
x1
0 metres(m) AOD, unless noted otherwise.
80
P1 EA 3. All Dimensions and levels to be checked on site and any
35
PFC 200x75x23
55 72 45 76 discrepancies should be reported to GHD LIVIGUNN.
110
141 45 22 4. This drawing is to be read in conjunction with relevant project
119
1 P TYP
TY
145
standards and specification.
75
33 75 33
207
~10~ 5. Holes to be drilled through and fastened to plates
51
212
60
~10~
6. Pipe supports on hold.
35
35
UB 356x171x45
P98
UB 203x133x30
97
22
STEELWORK:
100
P79
72
22
93
P98 TYP
77
~10~
145
TYP 45a
75
C15
M9 M9 22 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
35
PFC 200x75x23 243 104 22
35
specification (NSSS) Fifth Edition 2010, CE Marking Version.
167 117 2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
96
N1 P79 45a
ITEM NO.45a P98 P99 grade S355JRH to BS EN 10210-2.
1 No. 1 No. 1 No.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
TOP VIEW P98 N3 N3 75
and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
P99
100
2 Nos. 4. Steel overhead runway beams shall be tested in accordance with
UB 356x171x45 BS 1993-6 and BS 2853.
C15 5. All Connections forces shown are U.L.S. value.
60
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
EA
80
P79 bolts
x10
=145=
P79 22 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
60 P99 P98 (3 NOS.) P99 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
=141=
~10~ to be 4mm fillet welds.
UB 203x133x30 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
332
galvanised coating to be min 85m. Environment category C3 to BS
291
EN ISO 14713-1 and design life of 25 years. The surface protection
63
C15 22
TO SUIT M20 classification shall be as follows conforming to the classes defined
22 45a in EN BS 12944:
- For any steel elements inside, not including insulated piping and
175
75
P1 P98
(2 NOS.) lagging: Class C3(Urban and Industrial atmosphere, moderate
P98 ~10~
sulphur dioxide levels and production areas with the high humidity).
C15
N4 - For the steel elements in the fuel storage, not including insulated
62
C15
and lagging: Class C4(Industrial and coastal chemical processing
plants).
22 10 - For the outside steel elements, not including insulated piping and
TO SUIT M20
lagging: Class C4(Industrial and Coastal chemical processing plants)
TOP VIEW SECTION N4-N4 TYPE 63 SECTION N3-N3 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
1 Location
Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
200 105 30 Overhead crane supporting structures
40 79 59
SECTION M9-M9 SECTION N1-N1 33 79 88
(Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
TYPE 62 22 approved for grouting operatiions. The grout must extend between
50
193 72 C15 TO SUIT M20
2 Locations 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
70
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
70
136 66 BS 8300 Handrails
22
132
~10~ To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
390
150
381
205
390
22 with HIT-V-R Rods, minimum 270mm embedent.
36
~10~
16. Over material (O.M.) to be cut and cut out to be applied after final
150
~10~ 22
TYP P123 dimension check.
81
74
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
70
281 141 115
265
70
50
0= C15
=8 P 118 163 REFERENCE DOCUMENTS:
TY
P100 22 75 - KEY PLAN - BARRY_01_DWG_23_20700
EA
22
x10
85 48
- C & S REPORT (REP) - BARRY_01_20076
93
~10~
- C & S REPORT (REP) - BARRY_01_20077
206
PFC 200x75x23
Plan El 10.400m
224
224
5
TY
TYP
291
P121 P123 P136 P137 SECTION R1-R1 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
131
TYP
~10~ 7 145
Plan El 13.500
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
85
Q9 Sections A, B, P, R
67
SHSC 90x5
177 C15
P121 P121 Sections C, D.
EA - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
=80
45a 124 133 80x
90
TY
10 10 Hall Sections E, F, G
80x
=
P
EA
257 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
145
PFC 200x75x23
SHSC 90x5
P
TY P121 Rev Date Description By Chk App
96
Revision
P100 101
1 No. 1 No. HARRIS PYE UK LIMITED,
22
N4 N4 R1 TO SUIT M20
R1
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
P101 NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
80 80 C15 C15
P137
22 PFC 200x75x23 P123
TO SUIT M20 45 35 22 22
63
CLIENT
35
~10~ ~10~
PFC 200x75x23
45
=145=
75
145
75
x10
80
P122 P122
EA
TYP
381
(1 NO.) P136
35
PROJECT
63
22
TYP
45a
BARRY - BIOMASS UK No 2 LLP
TITLE
HOLD
C15 C15
TURBINE PLATFORM
TOP VIEW SECTION N4-N4 ITEM NO.45a 75 FABRICATION DRAWING
1 No. TYP
Q9 SCALE DRAWING SIZE DRAWN
TYPE 64 SIDE VIEW TYPE 83 SECTION Q9-Q9 1:5 A1 ES/MU
1 Location 1 Location DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
N8 =8
0=
294 350 GENERAL NOTES:
55 170 124
x10
TYP 1. Do not scale from this drawing.
80
EA
2. All dimensions are in millimetres(mm) and all levels are in
22 141 metres(m) AOD, unless noted otherwise.
C15 C15 3. All Dimensions and levels to be checked on site and any
33 75 33
UB 356x171x45 discrepancies should be reported to GHD LIVIGUNN.
42 76
53
85
145
88
22 22 4. This drawing is to be read in conjunction with relevant project
74
~10~ 66 70
standards and specification.
TYP
22
188
35
~10~ ~10~ P42
(4 NOS.)
TYP 5. Holes to be drilled through and fastened to plates
22 22
62
6. Pipe supports on hold.
235
205
TO SUIT M20 TYP ~10~ 22
36
TYP
N7
145
75
~10~
152
P104
STEELWORK:
132
C15 C15
150
147
22
76
97
35
P79 1. All works are to be carried out in accordance with the
UB 203x133x30 22 recomendation of the of the national structural steelwork
278 72 TYP specification (NSSS) Fifth Edition 2010, CE Marking Version.
P105 2. All hot rolled general steelwork and base plates to be grade
191 103 S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
P42 P42 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
P79 P102 and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
N5 N5 BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
N8 TOP VIEW N7 SECTION N7-N7 P104 P105 P102 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
1 No. 1 No. 1 No. bolts
137 340 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
10 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
UB 203x133x30
=141= to be 4mm fillet welds.
C15
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
75 UB 356x171x45 galvanised coating to be min 85m. Environment category C3 to BS
P104 EN ISO 14713-1 and design life of 25 years. The surface protection
66
classification shall be as follows conforming to the classes defined
P79 22 P42 P42 in EN BS 12944:
(2 NOS.) - For any steel elements inside, not including insulated piping and
P102 lagging: Class C3(Urban and Industrial atmosphere, moderate
75
~10~
=215= 215 sulphur dioxide levels and production areas with the high humidity).
332
70 75 70 - For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
66
145
plants).
75
22 - For the outside steel elements, not including insulated piping and
TO SUIT M20 lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
=203=
203
22 ~10~
68
C15 P103
22 following structure which are defined as EXC3:
Runway Beam
P105
Brackets supporting runway beam
Column supporting brackets ON HOLD
60
=
N6 N6 22
TO SUIT M20
22 22
TYP
Overhead crane supporting structures
TO SUIT M20 (Turbine building, workshop)
11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
TYPE 65 approved for grouting operatiions. The grout must extend between
1 Location 120mm and 50mm past the base plates edges.
SECTION N5-N5 SECTION N8-N8 P103 P103 13. Nominal grout thickness is 25mm u.n.o.
1 No. 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
64 To steelway or approved equivalent supplier.
P2 P1 TYP 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
C15 C15 350 135 dimension check.
17. - Indidacates area on base plate for drilling holes for
UB 356x171x45
22 22 chemical anchors.
30 75 30
TYP
188
53
74
(4 NOS.) 70 66
UB 203x133x30
22
40
~10~
P79
TYP
TYP REFERENCE DOCUMENTS:
C15 C15
22
- KEY PLAN - BARRY_01_DWG_23_20700
36
~10~
150
70
22 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
152
132
P42 P42 - C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
76
40
P106
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
P108 Plan El 10.400m
22
TYP - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
N9 N9 72 278 Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
P2 P1 Plan El 13.500
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
TOP VIEW SECTION P2-P2 P108 P106 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
1 No. 1 No.
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
340 137 75
Rev Date Description By Chk App
10 =215= 215 Revision
=141=
70 75 70
HARRIS PYE UK LIMITED,
UB 356x171x45
HANGER 5 & 6, BONA ROAD
C15 LLANDOW TRADING ESTATE,
66
NEAR COWBRIDGE
75
75
VALE OF GLAMORGAN, CF71 7PB
P106 www.harrispye.com
P42 P42 22
203
75
P106 P107
68
68
~10~
22
~10~ P79
(1 NO.)
CLIENT
332
60
60
22 22 22
145 P79 TO SUIT M20 TO SUIT M20 TYP
PROJECT
P107 C15
BARRY - BIOMASS UK No 2 LLP
=80
UC 203x203x46
TITLE
=
P3 P3
P108 TURBINE PLATFORM
FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
SECTION N9-N9 SECTION P1-P1 SECTION P3-P3 P107 1:5 A1 ES/MU
TYPE 66 1 No.
DRAWING No. REV.
1 Location XXX-XXX-XXX-XXX-XXX A0
=360=
=360= =425=
DO NOT SCALE - IF IN DOUBT ASK
141 35 75 140 75 35
35 75 140 75 35 35 75 205 75 35 NOTES
33 75 33
GENERAL NOTES:
35
35
35
UB 356x171x45
1. Do not scale from this drawing.
35
75
128
2. All dimensions are in millimetres(mm) and all levels are in
75
75
40
180
~20~ ~20~
P79 3. All Dimensions and levels to be checked on site and any
100
discrepancies should be reported to GHD LIVIGUNN.
60
295
75
SHS 90x5 4. This drawing is to be read in conjunction with relevant project
=360=
SHS 70x5 UC 152x152x37
140
340
120
47 standards and specification.
P109
~10~ 5. Holes to be drilled through and fastened to plates
357
87
87
6. Pipe supports on hold.
75
213
115
46 ~25~ STEELWORK:
75
75
22 46
60
35
100
P79 1. All works are to be carried out in accordance with the
35
recomendation of the of the national structural steelwork
40
35
specification (NSSS) Fifth Edition 2010, CE Marking Version.
35
35
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
22 grade S355JRH to BS EN 10210-2.
TYP 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
P9 P9 and Holding Down Bolts designed by client. Details to be confirmed
TYPE 67 TYPE 69 TYPE 71 by civil contractor.
9 Locations 4. Steel overhead runway beams shall be tested in accordance with
5 Locations 2 Locations
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
TOP VIEW P109 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
2 Nos. bolts
=360= =360=
=141= 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
=485= 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
35 75 140 75 35
35 75 140 75 35 to be 4mm fillet welds.
35 75 265 75 35 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
35
UB 203x133x30
35
classification shall be as follows conforming to the classes defined
35
in EN BS 12944:
75
115
P109
75
~20~ - For any steel elements inside, not including insulated piping and
75
lagging: Class C3(Urban and Industrial atmosphere, moderate
C10 C10 sulphur dioxide levels and production areas with the high humidity).
SHS 70x5 SHS 90x5 - For the steel elements in the fuel storage, not including insulated
295
75
UC 203x203x46
=360=
140
46 46
and lagging: Class C4(Industrial and coastal chemical processing
=340=
plants).
120
22 46
180
~20~ - For the outside steel elements, not including insulated piping and
75
22 lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
332
P79
75
following structure which are defined as EXC3:
35
75
~10~ ~10~
(8 NOS.) Runway Beam
~20~ Brackets supporting runway beam
ON HOLD
35
Column supporting brackets
35
Horizontal TIE members
Overhead crane supporting structures
(Turbine building, workshop)
C10 C10 11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
69
TYPE 24 TYPE 68 TYPE 70 TYPE 73
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
8 Locations
2 Locations 1 Location 3 Locations 120mm and 50mm past the base plates edges.
SECTION P9-P9 13. Nominal grout thickness is 25mm u.n.o.
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
=425=
BS 8300 Handrails
44 45 35 96 245 To steelway or approved equivalent supplier.
35 75 205 75 35 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
35 61 104 80 62 with HIT-V-R Rods, minimum 270mm embedent.
P126 16. Over material (O.M.) to be cut and cut out to be applied after final
35
50
EXISTING REFERENCE
50
chemical anchors.
75
~20~
REFERENCE DOCUMENTS:
244
245
144
145
UC 152x152x23 ~10~ ~10~
- KEY PLAN - BARRY_01_DWG_23_20700
TYPE 84
=425=
50
50
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
22 Plan El 10.400m
22 22 TYP
TO SUIT M20 TYP - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
22 22 Plan El 10.400m
75
20
UC 203x203x46
UC 203x203x46
R3 R3 Revision
C15
HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
EXISTING REFERENCE LLANDOW TRADING ESTATE,
P126 P126
NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
CHEMICAL ANCHOR P125 www.harrispye.com
C15 C15
BASE PLATE CHEMICAL ~10~
FILL 22 22
381
CLIENT
GROUT
~10~ ~10~
CONCRETE
(2 NOS.) (2 NOS.)
PROJECT
C15
BARRY - BIOMASS UK No 2 LLP
CHEMICAL FILL DETAILS 75
TITLE
FOR TYPE 67 AND TYPE 73
See note 3(STEEL WORK)
C15 C15
TURBINE PLATFORM
FABRICATION DRAWING
75
SCALE DRAWING SIZE DRAWN
R2 1:5 A1 ES/MU
SIDE VIEW SECTION R2-R2 P124 DRAWING No. REV.
2 Nos.
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
=1
40
GENERAL NOTES:
5
8.9
x =
8
S 1. Do not scale from this drawing.
CH
=14
x5 4. This drawing is to be read in conjunction with relevant project
88.9
0=
CHS standards and specification.
P74 5. Holes to be drilled through and fastened to plates
UC 203x203x46
6. Pipe supports on hold.
Q1 P73
STEELWORK:
P109
1. All works are to be carried out in accordance with the
P73
301 148 recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
UB 356x171x45 P74 2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
P73 grade S355JRH to BS EN 10210-2.
C15 C15 53 49 74
EL 8.764 U/S 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
75 22 BASE PLATE
148
P111 and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
53
P79 P79 49
(4 NOS.)
4. Steel overhead runway beams shall be tested in accordance with
22 22
SIDE VIEW BS 1993-6 and BS 2853.
53
49
5. All Connections forces shown are U.L.S. value.
~10~ ~10~
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
332
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
22 bolts
178
~10~ TYP 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
149
90 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
25
C15 C15 P73 galvanised coating to be min 85m. Environment category C3 to BS
C15 EN ISO 14713-1 and design life of 25 years. The surface protection
classification shall be as follows conforming to the classes defined
450 P2 in EN BS 12944:
(2 NOS.)
22
P111 - For any steel elements inside, not including insulated piping and
181
~10~
lagging: Class C3(Urban and Industrial atmosphere, moderate
Q1 sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
SIDE VIEW SECTION Q1-Q1 P109 C15 and lagging: Class C4(Industrial and coastal chemical processing
2 Nos. plants).
- For the outside steel elements, not including insulated piping and
TYPE 74 lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
2 Locations
SECTION Q2-Q2 following structure which are defined as EXC3:
Runway Beam
324 92
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
0= Overhead crane supporting structures
=14
(Turbine building, workshop)
44
CH
S8
11. Allowance for levelling shims and grout thickness not to be less
8.9
P74
than 15mm and no more than 25mm. May vary for large base plates.
5x
22
67 12. Use non-shrink flowable grout fosroc conbextra GP or similar
22 approved for grouting operatiions. The grout must extend between
TYP
140 120mm and 50mm past the base plates edges.
189
33
Q2 13. Nominal grout thickness is 25mm u.n.o.
300
P110 35 70 35
~10~
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
63
110 BS 5395/EN ISO 14122 Platform, Stairs
50
72 BS 8300 Handrails
37 31 62
To steelway or approved equivalent supplier.
82
67
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
160
22 C15
75
~10~
with HIT-V-R Rods, minimum 270mm embedent.
140
P73
22 16. Over material (O.M.) to be cut and cut out to be applied after final
140 dimension check.
35
~10~
PFC 200x90x30 35 70 35 289 126
17. - Indidacates area on base plate for drilling holes for
22 chemical anchors.
TYP
415
50
P73 P74 P111 REFERENCE DOCUMENTS:
TYPE 76
160
UB 152x152x37
2 Nos. - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
=120=
45 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
35
0=
=14 110 Sections C, D.
120
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
CH
50
S8
P73 P73
Hall Sections E, F, G
8.9
P74 P115
x5
35
10 22 A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
140
~10~
P74 1 No.
NEAR COWBRIDGE
VALE OF GLAMORGAN, CF71 7PB
2 Nos. www.harrispye.com
175 199
172
(2 NOS.) (2 NOS.)
78 45b
~10~ ~10~ 58 41
UB 254x102x28 C15 C15
CLIENT
115
22 PFC 150x75x18
TYP ~10~
P115
63
75
303
C15
38
P77 PROJECT
40
BARRY - BIOMASS UK No 2 LLP
188
TYP ~10~
41
134
~10~
TITLE
SECTION Q5-Q5 TURBINE PLATFORM
375
Q2 FABRICATION DRAWING
SIDE VIEW IWO UB 254x102x28 SECTION Q2-Q2 P110 SCALE DRAWING SIZE DRAWN
2 Nos.
TYPE 80 1:5 A1 ES/MU
TYPE 75 1 Location DRAWING No. REV.
2 Locations
XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
NOTES
Q3 410
75 GENERAL NOTES:
PFC 200x90x30 PFC 200x90x30
140 1. Do not scale from this drawing.
C15
Q6 2. All dimensions are in millimetres(mm) and all levels are in
PF
35 70 35
C
metres(m) AOD, unless noted otherwise.
20
0x
74 53 49 110
75
3. All Dimensions and levels to be checked on site and any
x2
22
113
3
~10~
discrepancies should be reported to GHD LIVIGUNN.
172
P112
50
~10~ 4. This drawing is to be read in conjunction with relevant project
(4 NOS.)
standards and specification.
49
53
P112 P112 PFC 200x75x23
140
261
5. Holes to be drilled through and fastened to plates
160
75
~10~
C15 6. Pipe supports on hold.
53
49
22 ~10~ P1
148
STEELWORK:
35
P113 P73 P73 P113
22
74
P74 P74 P113 22
TYP 22 1. All works are to be carried out in accordance with the
TYP
TYP
22
Q6 recomendation of the of the national structural steelwork
CHS
88.9
x5 CHS
88.9
x5
148 261 P73 P74 specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
1 No. 1 No. S355JR to BS EN 10025-2. All structural hollow sections to be
TYP P73
TOP VIEW grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
=14
SHSC 90x90x5
P114
0=
Q4 60
by civil contractor.
2 Nos. 55 60 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
Q3 PFC 200x75x23 PFC 200x75x23 5. All Connections forces shown are U.L.S. value.
C15 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
P119 C15
70
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
SIDE VIEW SECTION Q3-Q3 P1
(1 NO.) bolts
22 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
P1
175
175
~10~
60
~10~ P1 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
(2 NOS.)
(1 NO.) to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
70
286 C15 C15
EN ISO 14713-1 and design life of 25 years. The surface protection
140 classification shall be as follows conforming to the classes defined
22 10 in EN BS 12944:
31 67 62 35 70 35
TO SUIT M20 - For any steel elements inside, not including insulated piping and
54
110 P114
69
50
SECTION Q6-Q6
33
- For the steel elements in the fuel storage, not including insulated
P73 and lagging: Class C4(Industrial and coastal chemical processing
243
31
140
160
22 22
75
P114
Q4
32
40 65 - For the outside steel elements, not including insulated piping and
~10~
lagging: Class C4(Industrial and Coastal chemical processing plants)
4
22
.3x
35
31
94
60
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
S
CH
40
22 following structure which are defined as EXC3:
TYP 22
TYP Runway Beam
ON HOLD
140
60
P74 Brackets supporting runway beam
=1
4
Column supporting brackets
0=
Horizontal TIE members
40
Overhead crane supporting structures
P113 P73 P74 22
TYP
(Turbine building, workshop)
2 Nos. 2 Nos. 2 Nos. 11. Allowance for levelling shims and grout thickness not to be less
SIDE VIEW SECTION Q4-Q4 than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
P119 approved for grouting operatiions. The grout must extend between
TYPE 77 TYPE 78 1 No.
TYPE 79a 120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
2 Locations 2 Locations 1 Location
14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
280
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
55 225 with HIT-V-R Rods, minimum 270mm embedent.
193 65 55 16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
35 123 35 30 35 22
60 17. - Indidacates area on base plate for drilling holes for
TO SUIT M20 chemical anchors.
55
C15 C15
40
40
110
78
C15
60
~10~ P118
22 C15
22 (4 NOS.) REFERENCE DOCUMENTS:
186
22
188
P144
- KEY PLAN - BARRY_01_DWG_23_20700
113
113
60
~10~ ~10~
140
P117 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
271
C15
22 - C & S REPORT (REP) - BARRY_01_20076
150
312
312
~10~ P138
22 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
405
14 Plan El 10.400m
120
120
~10~ P73
20
60
22 - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
45
C15 P140 P141 Plan El 10.400m
85
40
Plan El 13.500
58
119 P74
P74 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
134
22 22 22 Sections A, B, P, R
TYP TYP TO SUIT M20 1 No.
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
CH
22
S
54
60
TYP Sections C, D.
.3x
4
CH
Revision
S
60
.3x
4
R7 55
FRONT VIEW P116 HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
83
1 No. LLANDOW TRADING ESTATE,
UB 203x133x30
NEAR COWBRIDGE
140 VALE OF GLAMORGAN, CF71 7PB
P118
C15 C15 www.harrispye.com
35 70 35 P74
264
P144 P144 110 ~10~
22
P146 P117
181
50
188
~10~
C15 C15
~10~
P145 63
35
PROJECT
22
R6 P143 R6 P143 TYP 22
PFC 150x75x18
PFC 150x75x18
22
BARRY - BIOMASS UK No 2 LLP
P73 P74 FRONT VIEW P117 TITLE
R7 1 No. 1 No. 1 No.
TURBINE PLATFORM
24 75 94
TYPE 81 TYPE 82 FABRICATION DRAWING
FRONT VIEW SECTION R6-R6 1 Location 1 Location SCALE DRAWING SIZE DRAWN
1:5 A1 ES/MU
TYPE 79 DRAWING No. REV.
1 Location
XXX-XXX-XXX-XXX-XXX A0
75 L 152 L
75 L DO NOT SCALE - IF IN DOUBT ASK
FOR ITEM FOR ITEM
3167 100 1400 100 629 100 625 100 40
45
10a ONLY 10a ONLY NOTES
TYP
56 40 56
56 40 56
GENERAL NOTES:
150
200
152
22
TYP 1. Do not scale from this drawing.
18 ENDCUT-A ENDCUT-B
ENDCUT-A ENDCUT-B TYP 2. All dimensions are in millimetres(mm) and all levels are in
PFC 150 x 75 x 18 UC 152 x 152 x 23 metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
PFC 200 x 75 x 23 PFC 150x75x18 PFC 150x75x18
165
1340 75 1042 75
6281+100 O.M.
1288 75 1186 75 1105
UC 152x152x23 discrepancies should be reported to GHD LIVIGUNN.
ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B 4. This drawing is to be read in conjunction with relevant project
ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B standards and specification.
PFC 200x75x23 PFC 200x75x23 10a 1 3341+100 O.M. N/A N/A
17a 1 1730+100 O.M. N/A N/A 17h 1 225+100 O.M. N/A N/A 5. Holes to be drilled through and fastened to plates
ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B 10b 1 4950+100 O.M. N/A N/A
17j
6. Pipe supports on hold.
91
17b 1 1434+100 O.M. N/A N/A 1 1105+100 O.M. DET-23 DET-23
1f 2 985+100 O.M. DET-1 DET-1 1c8 1 1068+100 O.M. N/A DET-4
10d 2 275+100 O.M. SEE TYPE 26(SHT. 22) N/A
17c 1 395+50 O.M. N/A DET-22 17k 1 1105+100 O.M. DET-23 DET-23
1g 1 4325+100 O.M. DET-1 DET-30 1c9 1 1090+100 O.M. DET-4 DET-4 STEELWORK:
75
303
17d 1 280 N/A N/A 17l 1 1105+100 O.M. DET-23 DET-23
1h 1 2975+100 O.M. DET-1 DET-30 1d1 1 972+100 O.M. DET-4 DET-30
1j 17e 1 395+100 O.M. N/A DET-22 17m 1 695+100 O.M. DET-23 N/A 22 88,9 L 1. All works are to be carried out in accordance with the
138
1 2995+100 O.M. DET-1 DET-30 1d2 1 1177+100 O.M. DET-4 N/A
recomendation of the of the national structural steelwork
1k 1 1110+100 O.M. DET-1 DET-1 1d3 1 1075+100 O.M. N/A DET-4
17f 1 280 N/A N/A 17n 1 225 N/A N/A TYP
specification (NSSS) Fifth Edition 2010, CE Marking Version.
17g 1 695+100 O.M. N/A DET-22
1l 1 635+100 O.M. DET-30 DET-30 1d4 1 1228+100 O.M. DET-4 DET-4 2. All hot rolled general steelwork and base plates to be grade
1m 1 4325+100 O.M. DET-30 DET-1 1d5 1 1198+100 O.M. DET-5 DET-5 ITEM NO: 6a S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
1n 2 747+100 O.M. N/A DET-2 1d6 1 1198+100 O.M. DET-5 DET-5 90 L UB 305x165x40 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
CUTOUT
1p
1q
1 985+100 O.M.
1 2975+100 O.M. DET-30
DET-1 DET-1
DET-1
1d7
1d8
1
1
1198+100 O.M.
1198+100 O.M.
DET-5
DET-5
DET-5
DET-5
CHS 88.9 x 5 and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
1r 1 2975+100 O.M. DET-30 DET-1 1d9 1 1198+100 O.M. DET-5 DET-5 154 L CHS 88.9x5 4. Steel overhead runway beams shall be tested in accordance with
200
66 75 ITEM NO. QTY LENGTH (mm) BS 1993-6 and BS 2853.
1s 1 1110+100 O.M. DET-1 DET-1 1e1 1 2904+100 O.M. DET-6 DET-6 5. All Connections forces shown are U.L.S. value.
1t 1 1110+100 O.M. DET-1 DET-1 1e3 1 1197+100 O.M. DET-5 DET-6 11a 1 2775+100 O.M. N/A 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
1u 1 1110+100 O.M. DET-1 DET-1 1e5 1 2904+100 O.M. DET-6 DET-6 11b 1 1370+100 O.M. N/A Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
=60=
162
11c 1 1370+100 O.M. N/A bolts
1w 1 500 N/A N/A 1e6 1 1041+100 O.M. DET-26 DET-30 22
1x 1 925+100 O.M. DET-30 DET-1 1e8 1 761+100 O.M. DET-7 DET-7
PFC 200 x 90 x 30 TYP 11d 1 927+100 O.M. 45
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
1y 1 920+100 O.M. DET-30 DET-1 1e9 1 761+100 O.M. DET-7 DET-7 PFC 200x90x30
11e 1 927+100 O.M. 45 to be 4mm fillet welds.
1z 1 1950+100 O.M. DET-1 DET-1 1f1 1 1516+100 O.M. DET-5 DET-1 11f 2 810+100 O.M. 57 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
1a1 1 1950+100 O.M. DET-1 DET-1 1f2 1 1280+100 O.M. DET-30 DET-1
ITEM NO.
2a
QTY
1
LENGTH (mm)
1887+100 O.M.
ENDCUT-A
DET-8
ENDCUT-B
DET-30
UC 152 x 152 x 37 galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
70 L
1a2 1 995+100 O.M. DET-1 DET-1 1f3 1 870+100 O.M. DET-30 DET-30
2b 1 1965+100 O.M. DET-9 DET-8 classification shall be as follows conforming to the classes defined
UC 152x152x37 in EN BS 12944:
1a3 1 625+100 O.M. DET-31 DET-1 1f4 1 2106+100 O.M. DET-1 DET-1
2e 1 1350+100 O.M. N/A N/A - For any steel elements inside, not including insulated piping and
ITEM NO. QTY LENGTH (mm)
70
1a8 1 2266+100 O.M. DET-3 DET-30 1f5 1 2106+100 O.M. DET-1 DET-1 2g 2 728+100 O.M. N/A N/A
16a 1 4950+100 O.M. lagging: Class C3(Urban and Industrial atmosphere, moderate
1a9 1 2145+100 O.M. DET-1 DET-30 1f6 1 2076+100 O.M. DET-30 DET-27 sulphur dioxide levels and production areas with the high humidity).
2h 1 557+100 O.M. N/A N/A
1b1 1 2110+100 O.M. DET-1 DET-30 1f7 1 2076+100 O.M. DET-30 DET-27 2j 1 557+100 O.M. N/A N/A
16b 1 4950+100 O.M.
SHSC 70 x 70 x 5 - For the steel elements in the fuel storage, not including insulated
1b2 1 1110+100 O.M. DET-1 DET-1 1f8 1 761+100 O.M. DET-26 DET-7 and lagging: Class C4(Industrial and coastal chemical processing
2k 1 557+100 O.M. N/A N/A SHSC 90x90x5 SHSC 90x90x5 plants).
1c4 1 760+100 O.M. DET-1 DET-2 1f9 1 350 N/A N/A
2l 1 557+100 O.M. N/A N/A ITEM NO. QTY LENGTH (mm) ITEM NO. QTY LENGTH (mm) - For the outside steel elements, not including insulated piping and
1c5 1 930+100 O.M. DET-4 N/A 1g1 1 1050+100 O.M. DET-28 DET-29 134 L
2m 1 660+100 O.M. N/A N/A 15a 1 930+100 O.M. 15k 1 930+100 O.M.
lagging: Class C4(Industrial and Coastal chemical processing plants)
1c6 1 1177+100 O.M. N/A DET-4 1g6 1 250 N/A N/A 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
15b 1 930+100 O.M. 15l 1 930+100 O.M. following structure which are defined as EXC3:
1c7 1 1075+100 O.M. DET-4 N/A 1g7 1 350 N/A N/A L2 100
15c 1 930+100 O.M. 15m 1 930+100 O.M. Runway Beam
45
15d 1 930+100 O.M. 15n 1 930+100 O.M. Brackets supporting runway beam
ON HOLD
207
Column supporting brackets
15e 1 930+100 O.M. 15p 1 930+100 O.M.
Horizontal TIE members
45 L2 100 L3 100 15f 1 930+100 O.M. 15q 1 930+100 O.M. Overhead crane supporting structures
TYP 18 ENDCUT-A ENDCUT-B 15g 1 930+100 O.M. 15r 1 930+100 O.M. (Turbine building, workshop)
TYP
15h 1 930+100 O.M. 15s 1 930+100 O.M. 11. Allowance for levelling shims and grout thickness not to be less
90 L than 15mm and no more than 25mm. May vary for large base plates.
15j 1 930+100 O.M.
1 SET 18
TYP
UB 203 x 133 x 30 12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
75 L L 120mm and 50mm past the base plates edges.
UB 203x133x30
L2 100 L3 100 L4 100 L5 100 13. Nominal grout thickness is 25mm u.n.o.
200
ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B 14. Access platforms, handrails, stairs, ladders shall conforming to:
28 52
BS 4952 Grating
100
3a 1 1687+100 O.M. N/A N/A
BS 5395/EN ISO 14122 Platform, Stairs
200
20
To steelway or approved equivalent supplier.
ENDCUT-A ENDCUT-B 3d 1 560+100 O.M. N/A N/A 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
PFC 200x90x30 FB 100x10 with HIT-V-R Rods, minimum 270mm embedent.
PFC 200 x 75 x 23 ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B L2 (mm)
3f
3g
1
1
5910+100 O.M.
3895+100 O.M.
DET-14
DET-15
DET-15
DET-15
ITEM
QTY LENGTH (mm) L2 (mm) L3 (mm) L4 (mm) L5 (mm)
16. Over material (O.M.) to be cut and cut out to be applied after final
NO. dimension check.
2c 1 1886+100 O.M. DET-30 DET-33 752 3h 1 5910+100 O.M. DET-14 DET-14 23g 1 5160+100 O.M. 206 1400 1400 1400 17. - Indidacates area on base plate for drilling holes for
PFC 200x75x23
2d 1 1965+100 O.M. DET-8 DET-9 1244 3j 1 4440+100 O.M. DET-14 DET-14 chemical anchors.
ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B L2 (mm) L3 (mm)
3k 1 3482+100 O.M. DET-14 DET-14 L
1b 1 2975+100 O.M. DET-1 DET-30 940 1200 L2 100 L3 100 L4 100
90 L 3q 1 2905+100 O.M. DET-16 DET-16
1c 1 2975+100 O.M. DET-1 DET-30 740 1400
28 52
3r 1 870+100 O.M. N/A N/A REFERENCE DOCUMENTS:
100
1d 1 2975+100 O.M. DET-1 DET-30 740 1400
1e7 1 2117+100 O.M. DET-26 DET-6 926 731
3s 1 2672+100 O.M. N/A N/A - KEY PLAN - BARRY_01_DWG_23_20700
3t 1 2672+100 O.M. N/A N/A - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
FB 100 x 10
20
180
28 52
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
100
80 L
Hall Sections E, F, G
ENDCUT-A ENDCUT-B A0 24-08-2017 ISSUED FOR REVIEW ES/MU MM/RK SM
FB 100 x 10
20
80
28 52
256
100
8k 1 595+100 O.M. DET-24 DET-24 8x 1 1504+100 O.M. DET-24 DET-24
260
20
8m 1 1851+100 O.M. DET-24 DET-24
ENDCUT-A ENDCUT-B
ENDCUT-A ENDCUT-B
206 3681+100 O.M. UB 254 x 146 x 37 ITEM
FB 100x10 TITLE
UB 254 x 102 x 28 UB 254x146x37
NO.
QTY LENGTH (mm) L2 (mm) TURBINE PLATFORM
23c 1 783+100 O.M. 206
UB 254x102x28 ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B
23d 1 505+100 O.M. 206
FABRICATION DRAWING
216
ITEM NO. QTY LENGTH (mm) ENDCUT-A ENDCUT-B 5a 1 2755+100 O.M. DET-17 N/A
23h 1 600+100 O.M. 374
13c 1 4858+100 O.M. DET-21 DET-20 5b 1 2828+100 O.M. DET-17 DET-18 SCALE DRAWING SIZE DRAWN
23s 1 1475+100 O.M. 1000
5c 1 2828+100 O.M. DET-17 DET-18 NTS A1 ES / MU
23k 1 430+100 O.M. 305
ITEM NO: 9a 5d 1 2828+100 O.M. DET-17 DET-18 23j 1 292+100 O.M. N/A DRAWING No. REV.
UC 203x203x71 23w 1 12000 N/A XXX-XXX-XXX-XXX-XXX A0
DO NOT SCALE - IF IN DOUBT ASK
TOTAL LENGTH = 6670+100 O.M.
6000 670 NOTES
PART-A PART-B
GENERAL NOTES:
S 1. Do not scale from this drawing.
2. All dimensions are in millimetres(mm) and all levels are in
20
200 230 TYP HOLE 50 180 metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
430 6210 = 27 EQ. SPACE AT 230mm 30
discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
ITEM NO: 24 (2-nos) standards and specification.
5. Holes to be drilled through and fastened to plates
FB 65x10 6. Pipe supports on hold.
STEELWORK:
516
1. All works are to be carried out in accordance with the
R.E.
recomendation of the of the national structural steelwork
specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
221
grade S355JRH to BS EN 10210-2.
TOTAL LENGTH = 6728+100 O.M. 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
TOTAL LENGTH = 10190+100 O.M. by civil contractor.
6000 828
6000 4190 4. Steel overhead runway beams shall be tested in accordance with
PART-A PART-B
PART-A PART-B BS 1993-6 and BS 2853.
1134
280
11 11
TYP 109 5. All Connections forces shown are U.L.S. value.
TYP
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
28 52
28 52
S S
100
100
355 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
IR= bolts
60
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
20
20
980 100 1200 100 1400 100 1400 100 1400 100 1400 100 1400 100 576 100 1400 100 1250 100 1400 100 1400 100 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
221
to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
ITEM NO: 23a galvanised coating to be min 85m. Environment category C3 to BS
ITEM NO: 23l
R.E.
EN ISO 14713-1 and design life of 25 years. The surface protection
FB 100x10 516 classification shall be as follows conforming to the classes defined
FB 100x10 in EN BS 12944:
- For any steel elements inside, not including insulated piping and
R.E. R.E. lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
60 L 57 103 215 513 1432 513 215 103 57 plants).
- For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
90
TOTAL LENGTH = 3208+100 O.M.
IR=10 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
50
following structure which are defined as EXC3:
Runway Beam
R.E. ITEM NO: 27a (2-nos) Brackets supporting runway beam
ON HOLD
31
238
Column supporting brackets
FB 50x6 Horizontal TIE members
CHS 60.3 x 4 30 BEND-UP 90
Overhead crane supporting structures
(Turbine building, workshop)
CHS 60.3x4 CHS 60.3x4 11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
=
ITEM NO. QTY LENGTH (mm) ITEM NO. QTY LENGTH (mm)
12. Use non-shrink flowable grout fosroc conbextra GP or similar
=
19a 1 450+100 O.M. 45 N/A 19g 1 1306+100 O.M. N/A N/A approved for grouting operatiions. The grout must extend between
671
19b 1 450+100 O.M. 45 N/A 19h 2 775+100 O.M. 45 45 120mm and 50mm past the base plates edges.
65 253 155 516 13. Nominal grout thickness is 25mm u.n.o.
19c 1 843+100 O.M. 45 45 19j 1 776+100 O.M. 45 45
14. Access platforms, handrails, stairs, ladders shall conforming to:
19d 1 843+100 O.M. 45 45 19k 1 775+100 O.M. 45 45
TOTAL LENGTH = 318+100 O.M. BS 4952 Grating
70
19e 1 843+100 O.M. 45 45 19l 1 775+100 O.M. 45 45 BS 5395/EN ISO 14122 Platform, Stairs
19f 1 843+100 O.M. 45 45 BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
ITEM NO: 25 (4-nos) with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
FB 50x10 dimension check.
17. - Indidacates area on base plate for drilling holes for
754
chemical anchors.
109
968
4360+100 O.M.
60
89 L
REFERENCE DOCUMENTS:
- KEY PLAN - BARRY_01_DWG_23_20700
221
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
- C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
ITEM NO: 26 (8-nos)
152
RB 20
FB 50x6
HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
NEAR COWBRIDGE
42,2 L 20 420 VALE OF GLAMORGAN, CF71 7PB
377
www.harrispye.com
90 L
22
8
90
CLIENT
CHS 42.2 x 3.6 ITEM NO: 29 (2-nos)
54
310
CHS 42.2x3.6
SHSC 90 x 90 x 5 IR=78.9 CHS 42.2x3.6 CHS 42.2x3.6 CHS 42.2x3.6 ITEM NO. QTY LENGTH (mm) RB 20
ITEM NO. QTY LENGTH (mm) ITEM NO. QTY LENGTH (mm) ITEM NO. QTY LENGTH (mm) 30c1 1 665+100 O.M.
SHSC 90x90x5 SHSC 90x90x5
266
30b 6 1535+100 O.M. 30r 1 365+100 O.M. 30a6 1 380+100 O.M. 30c2 1 665+100 O.M.
7 PROJECT
ITEM NO. QTY LENGTH (mm) ITEM NO. QTY LENGTH (mm) R10
30c 6 1230+100 O.M. 30s 1 605+100 O.M. 30a7 1 205+100 O.M. 30c3 6 490+100 O.M.
14a 1 665+100 O.M. 14j 1 685+100 O.M. 446
47
30f 4 200+100 O.M. 30u 9 470+100 O.M. 30a9 1 395+100 O.M. 30c5 1 1335+100 O.M.
130
14c 1 930+100 O.M. 14l 1 1046+100 O.M. 30g 20 1440+100 O.M. 30v 1 5255+100 O.M. 30b1 1 415+100 O.M. 30c6 1 935+100 O.M.
14d 1 930+100 O.M. 14m 1 436+100 O.M. BEND-UP 90
30h 1 375+100 O.M. 30w 1 320+100 O.M. 30b2 1 2670+100 O.M. 30c7 1 340+100 O.M. TITLE
14e 1 930+100 O.M. 14n 1 300+100 O.M.
642 424
30j 1 715+100 O.M. 30x 2 1320+100 O.M. 30b3 7 190+100 O.M. 30c8 1 1385+100 O.M. TURBINE PLATFORM
14f 1 930+100 O.M. 14p 1 436+100 O.M.
14g 1 930+100 O.M. 14q 1 950+100 O.M. TOTAL LENGTH = 1066+100 O.M.
30k 1 245+100 O.M. 30y 2 235+100 O.M. 30b4 1 170+100 O.M. 30c9 1 305+100 O.M. 150 27
FABRICATION DRAWING
30l 1 960+100 O.M. 30z 47 1040+100 O.M. 30b5 1 1090+100 O.M. 30d1 1 770+100 O.M. 177+100 O.M.
14h 1 300+100 O.M.
30m 1 525+100 O.M. 30a1 1 3040+100 O.M. 30b6 1 590+100 O.M. 30d2 1 3440+100 O.M.
SCALE DRAWING SIZE DRAWN
ITEM NO: 30a (6-nos) 30n
30p
1
1
3900+100 O.M.
900+100 O.M.
30a2
30a4
1
1
3040+100 O.M.
355+100 O.M.
30b7
30b8
1
1
3200+100 O.M.
1820+100 O.M.
30d3
30d4
1
1
440+100 O.M.
2580+100 O.M.
ITEM NO: 32 (2-nos) NTS A1 ES / MU
FB 50x6 RB 20 DRAWING No. REV.
30q 1 615+100 O.M. 30a5 1 400+100 O.M. 30b9 1 320+100 O.M. 30d5 1 1080+100 O.M.
XXX-XXX-XXX-XXX-XXX A0
551 100 1400 100 1250 100 1400 100 1400 100 DO NOT SCALE - IF IN DOUBT ASK
45
NOTES
75 1747+100 O.M. GENERAL NOTES:
18
100 1648
TYP 1. Do not scale from this drawing.
75 6678+100 O.M.
2. All dimensions are in millimetres(mm) and all levels are in
75 6678+100 O.M. metres(m) AOD, unless noted otherwise.
200
200
standards and specification.
200
86 1597 65
6. Pipe supports on hold.
DET.1
6000 678
STEELWORK:
ITEM NO: 1a4, 1c2 & 1b7 6000 678
PART-A PART-B
PFC 200x75x23 PART-A PART-B ITEM NO: 1a7 1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
PFC 200x75x23 specification (NSSS) Fifth Edition 2010, CE Marking Version.
ITEM NO: 1a6 2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
PFC 200x75x23 grade S355JRH to BS EN 10210-2.
1721 + 100 O.M.
90 3. Connection design in accordance to BS-EN-1993-1-8. Base plates
75 1747 1057 60 604 and Holding Down Bolts designed by client. Details to be confirmed
35
24
100 1648 82 by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
63
BS 1993-6 and BS 2853.
65
R10
5. All Connections forces shown are U.L.S. value.
200
152
75
70
176
200
75 1658 + 100 O.M. 22 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
TYP Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
65
63
33 75 734 75
bolts
69 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
ITEM NO: 2f
24
TYP TYP TYP
63 75 63
86 1597 65 8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
PFC 200x90x30 to be 4mm fillet welds.
200
22 9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
ITEM NO: 1a5, 1c3 & 1b8 TYP 335 300 715 galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
PFC 200x75x23 classification shall be as follows conforming to the classes defined
59
in EN BS 12944:
85
- For any steel elements inside, not including insulated piping and
22 lagging: Class C3(Urban and Industrial atmosphere, moderate
59
TYP
L3 100
ITEM NO: 1v sulphur dioxide levels and production areas with the high humidity).
- For the steel elements in the fuel storage, not including insulated
PFC 200x75x23 204 448 75 827 and lagging: Class C4(Industrial and coastal chemical processing
30
18 plants).
TYP 30 153 102 - For the outside steel elements, not including insulated piping and
66
lagging: Class C4(Industrial and Coastal chemical processing plants)
203
22
75
TYP 10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
ENDCUT-A
following structure which are defined as EXC3:
62
75 L1 18
Runway Beam
35 172 75
TYP
1124 + 100 O.M.
734 75 33
ITEM NO: 4g
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
UC 203x203x46
200
1g2 790+100 O.M. 725 492 N/A Overhead crane supporting structures
1g4 1350 (Turbine building, workshop)
63
536+100 O.M. 473 339 DET-3
40 75 40
335 300 715 11. Allowance for levelling shims and grout thickness not to be less
than 15mm and no more than 25mm. May vary for large base plates.
200
22
65 L2 12. Use non-shrink flowable grout fosroc conbextra GP or similar
59
TYP
63
approved for grouting operatiions. The grout must extend between
ITEM NO: 1g2 & 1g4
85
120mm and 50mm past the base plates edges.
69 R10 22
TYP
13. Nominal grout thickness is 25mm u.n.o.
ITEM NO: 1b3
59
TYP
PFC 200x75x23 TYP 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
PFC 200x75x23 204 BS 5395/EN ISO 14122 Platform, Stairs
18 438 75 719 75 33
30
L3 100
TYP
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
63
66
624 100 125 520 125 100 325 100 90
with HIT-V-R Rods, minimum 270mm embedent.
TYP
37
203
30
22 22
75
75
ENDCUT-A 16. Over material (O.M.) to be cut and cut out to be applied after final
75 L1 dimension check.
66
62
17. - Indidacates area on base plate for drilling holes for
ITEM NO. L1 (mm) L2 (mm) L3 (mm) ENDCUT-A
18
chemical anchors.
1g3 790+100 O.M. 725 198 N/A
ITEM4a,4g
NO: 4a
TYP
TYP
38
1g5 636+100 O.M. 571 198 DET-3 2109 + 100 O.M.
200
UC 203x203x46
75 35 35
20
REFERENCE DOCUMENTS:
TYP - KEY PLAN - BARRY_01_DWG_23_20700
45 338 100 1140 100 1471 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
63
63
40 75 40
65 L2 TYP
- C & S REPORT (REP) - BARRY_01_20076
200
75
22 - C & S REPORT (REP) - BARRY_01_20077
TYP - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
ITEM NO: 1g3 & 1g5
63
63
Plan El 10.400m
69 18
PFC 200x75x23 TYP TYP
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
ITEM NO: 1b4 2990 + 100 O.M.
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
PFC 200x75x23 146 2643 75 272
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
75 229 75 229 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
91
891 100 1913 Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
256
75
22 Hall Sections E, F, G
TYP
A0 24-08-2017 ISSUED FOR REVIEW ES/MU MM/RK SM
91
200
200
18 45
TYP ITEM 1e2 ONLY Rev Date Description By Chk App
63
40 75 40
22
TYP
63
62
82 R10 45 CLIENT
SIM FROM OTHER SIDE
1e2,1e4 18
TYP
571+100 O.M.
866+100 O.M.
ITEM NO: 1e2, 1e4 HOLD
129 100 400 100 366
PFC 200x75x23 146 4906 + 100 O.M.
18
TYP
PROJECT
134 4240 + 100 O.M. 75 1288 75 1186 75 1204
45 45 18
91 75 1150 75 2849
BARRY - BIOMASS UK No 2 LLP
TYP
66
TYP
TYP 75
91
539 31 31 760
TYP
256
75
DET.3 22 TITLE
TURBINE PLATFORM
TYP
207
75
TYP
TYP
90
ITEM NO: 1c1 ITEM NO: 1b9 FABRICATION DRAWING
DET.18
TYP
HOLD
66
48
GENERAL NOTES:
S
66
75
22
207
1. Do not scale from this drawing.
74
48
152
TYP
2. All dimensions are in millimetres(mm) and all levels are in
22
66
TYP metres(m) AOD, unless noted otherwise.
31
22 3. All Dimensions and levels to be checked on site and any
TYP
discrepancies should be reported to GHD LIVIGUNN.
ITEM NO: 3m 171 63 75 7926
4. This drawing is to be read in conjunction with relevant project
90
UB 203x133x30 standards and specification.
5. Holes to be drilled through and fastened to plates
3m
66
6. Pipe supports on hold.
TYP
58 70 70
31
20
70
1309 + 100 O.M.
STEELWORK:
S ITEM NO: 10c
351
20
134 60 75 1110 64
UC 152x152x23 1. All works are to be carried out in accordance with the
215
recomendation of the of the national structural steelwork
66
168
75
22 TYP 2. All hot rolled general steelwork and base plates to be grade
82 42,2 6000 988
TYP S355JR to BS EN 10025-2. All structural hollow sections to be
66
20
and Holding Down Bolts designed by client. Details to be confirmed
ITEM NO: 3n ITEM NO: 12b by civil contractor.
UB 203x133x30 UB 356x171x45 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
3n 6988+100 O.M.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
ITEM NO: 30a3 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
134 1418 + 100 O.M. 102 6676 + 100 O.M. bolts
CHS 42.2x3.6 7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
64 178 75 1101 5599 75 713 75 195
20
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
66
90
R10 50 50 50 50 75 galvanised coating to be min 85m. Environment category C3 to BS
207
168
75
260
TYP
80
classification shall be as follows conforming to the classes defined
66
in EN BS 12944:
90
22
- For any steel elements inside, not including insulated piping and
20
TYP
22 lagging: Class C3(Urban and Industrial atmosphere, moderate
TYP
sulphur dioxide levels and production areas with the high humidity).
ITEM NO: 3p 6000 676 - For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
UB 203x133x30 22 100 22 75
70 102 4858 + 100 O.M. following structure which are defined as EXC3:
Runway Beam
604 60 4194 RB 50 RB 50
ON HOLD
20
20
Brackets supporting runway beam
66
22
Column supporting brackets
207
188
75
65
TYP R10
Overhead crane supporting structures
66
82 80 80 80 80
70
(Turbine building, workshop)
220
35 45 50 30
240
11. Allowance for levelling shims and grout thickness not to be less
10
125
35
22 than 15mm and no more than 25mm. May vary for large base plates.
ITEM NO: 3w HOLD TYP 12. Use non-shrink flowable grout fosroc conbextra GP or similar
35
48 approved for grouting operatiions. The grout must extend between
145
UB 203x133x30
75
20
TYP
120
120mm and 50mm past the base plates edges.
50
13. Nominal grout thickness is 25mm u.n.o.
6805 + 100 O.M.
ITEM NO: 13b 13b 14. Access platforms, handrails, stairs, ladders shall conforming to:
35
35
134 3456 75 3275 22 BS 4952 Grating
UB 254x102x28 TYP
22
BS 5395/EN ISO 14122 Platform, Stairs
TYP
BS 8300 Handrails
To steelway or approved equivalent supplier.
66
22 ITEM NO: 45a (112-nos) ITEM NO: 45b (1-no) 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
207
188
188
75
dimension check.
70 70 200 2368+100 O.M. 17. - Indidacates area on base plate for drilling holes for
53 100 2215 chemical anchors.
ITEM NO: 3l
52
UB 203x133x30
3l
200
REFERENCE DOCUMENTS:
96
1918 100 87 100 1160 100 1400 100 1400 100 635 100 1400 100 1128 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
45
22
- C & S REPORT (REP) - BARRY_01_20076
TYP
- C & S REPORT (REP) - BARRY_01_20077
48
S Plan El 10.400m
75
Plan El 10.400m
22 18 - BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
TYP TYP 6385 + 100 O.M.
Plan El 13.500
171 63 75 8557 60 1073 2427 75 75 3762 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
64
Sections C, D.
65
66
22
70
70
22 TYP
Hall Sections E, F, G
64
S TYP
351
Revision
64
S
203
75
90
80
=75=
80
22
351
22 TYP
TITLE
216
211
TYP
181
23
23
23
23
35 34 35 45 35 63 35 35
PFC 200x75x23 UB 203x133x30
23
22 1. Do not scale from this drawing.
40 75 40
75 40
40 75 40
75 40
40 75 40
R10 R10 R10
TYP R10 2. All dimensions are in millimetres(mm) and all levels are in
155
155
155
178
178
22
TYP metres(m) AOD, unless noted otherwise.
R10 R10 22 22
3. All Dimensions and levels to be checked on site and any
63
63
TYP TYP TYP TYP
23
discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
23
23
standards and specification.
DETAIL-1 DETAIL-2 DET-3
DETAIL-3 DETAIL-4 DETAIL-5 5. Holes to be drilled through and fastened to plates
6. Pipe supports on hold.
STEELWORK:
1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
82 48 98 69 specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
35 47 35 13 35 63 83 35 34
S355JR to BS EN 10025-2. All structural hollow sections to be
24
24
24
23
23
PFC 200x75x23 PFC 200x90x30 grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
40 75 40
75 40
39 75 39
39 75 39
39 75 39
R10 R10 and Holding Down Bolts designed by client. Details to be confirmed
R10 R10 R10 TYP
155
152
152
152
by civil contractor.
178
TYP TYP TYP 22
22 22 22 4. Steel overhead runway beams shall be tested in accordance with
63
TYP TYP TYP TYP BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
23
24
24
24
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
DETAIL-6 DETAIL-7 DETAIL-8 DETAIL-9 DETAIL-10 bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
82 classification shall be as follows conforming to the classes defined
in EN BS 12944:
98
69 64 - For any steel elements inside, not including insulated piping and
20
23
20
10
24
70
UB203x133x30 lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
R10 R10 R10 R10
- For the steel elements in the fuel storage, not including insulated
155
163
168
188
and lagging: Class C4(Industrial and coastal chemical processing
176
29
20
10
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
DETAIL-11 DETAIL-12 DETAIL-13 DETAIL-14 DETAIL-15
DET-11 Runway Beam
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
Overhead crane supporting structures
82
(Turbine building, workshop)
20
11. Allowance for levelling shims and grout thickness not to be less
70 48
than 15mm and no more than 25mm. May vary for large base plates.
20
21
80 R10 12. Use non-shrink flowable grout fosroc conbextra GP or similar
82 UB 254x102x28
20
312
R10 13. Nominal grout thickness is 25mm u.n.o.
R10
220
14. Access platforms, handrails, stairs, ladders shall conforming to:
214
187
182
BS 4952 Grating
R10 R10 R10
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
21
20
20
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
DETAIL-16 DETAIL-17 DETAIL-18 DETAIL-19 DETAIL-20 16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
82 83
REFERENCE DOCUMENTS:
20
UB 254x102x28 35 48
- KEY PLAN - BARRY_01_DWG_23_20700
23
70 42 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
UB 203x133x30
10
10
R10
PFC 150x75X18 PFC 150x75X18 - C & S REPORT (REP) - BARRY_01_20076
40 75 40
- C & S REPORT (REP) - BARRY_01_20077
240
C15 22 22
47
C15 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
155
TYP
130
130
33
C15 C15 TYP - BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
35 75
Plan El 10.400m
10
23
10
DET-24 -
A0
Rev
Sections A, B, P, R
BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
24-08-2017 ISSUED FOR REVIEW
Date Description
ES/MU MM/RK SM
By Chk App
48 82 83 82
TYP 35
23
23
23
23
PFC 200x75x23 PFC 200x75x23 TYP Revision
63
R10 HARRIS PYE UK LIMITED,
R10 R10 HANGER 5 & 6, BONA ROAD
R10
155
22
75
178
178
178
62
VALE OF GLAMORGAN, CF71 7PB
www.harrispye.com
PROJECT
64
45 69 98
BARRY - BIOMASS UK No 2 LLP
240
TYP
10
23
TITLE
188
155
152
R10 R10
75
22
TYP
TYP TYP TURBINE PLATFORM
62
FABRICATION DRAWING
23
240
10
260
260
280
260
10 11 - BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
01 - BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
260 Hall Sections E, F, G
260 256 260 260
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
Rev Date Description By Chk App
DET.1a
(SHT.46) Revision
DET.1a DET.1a
(SHT.46) (SHT.46) HARRIS PYE UK LIMITED,
HANGER 5 & 6, BONA ROAD
LLANDOW TRADING ESTATE,
DET.1a DET.1a DET.1a DET.1a DET.1a DET.1a DET.1a NEAR COWBRIDGE
(SHT.46) (SHT.46) (SHT.46) (SHT.46) (SHT.46) (SHT.46) (SHT.46) VALE OF GLAMORGAN, CF71 7PB
TAW www.harrispye.com
1
CLIENT
PROJECT
STEELWORK:
1. All works are to be carried out in accordance with the
recomendation of the of the national structural steelwork
62 63 specification (NSSS) Fifth Edition 2010, CE Marking Version.
2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
TAW and Holding Down Bolts designed by client. Details to be confirmed
A by civil contractor.
60 61 4. Steel overhead runway beams shall be tested in accordance with
BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
TAW 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
2 Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
TAW to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
2 galvanised coating to be min 85m. Environment category C3 to BS
46 47
58 59 EN ISO 14713-1 and design life of 25 years. The surface protection
45 classification shall be as follows conforming to the classes defined
in EN BS 12944:
- For any steel elements inside, not including insulated piping and
1254
lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
1734
- For the steel elements in the fuel storage, not including insulated
and lagging: Class C4(Industrial and coastal chemical processing
56 57 plants).
- For the outside steel elements, not including insulated piping and
lagging: Class C4(Industrial and Coastal chemical processing plants)
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
480
following structure which are defined as EXC3:
Runway Beam
140
320
Brackets supporting runway beam
Column supporting brackets
Horizontal TIE members
ON HOLD
42 44 44a Overhead crane supporting structures
43
(Turbine building, workshop)
390
11. Allowance for levelling shims and grout thickness not to be less
54 55 than 15mm and no more than 25mm. May vary for large base plates.
12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
39 40 41 14. Access platforms, handrails, stairs, ladders shall conforming to:
52 53 BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
BS 8300 Handrails
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
427 with HIT-V-R Rods, minimum 270mm embedent.
16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
50 17. - Indidacates area on base plate for drilling holes for
chemical anchors.
51
270
48 49 REFERENCE DOCUMENTS:
- KEY PLAN - BARRY_01_DWG_23_20700
830
37 38
- BASE PLATE DETAILS - BARRY_01_DWG_23_20750
36 36a - C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
- BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
Rev Date Description By Chk App
Revision
PROJECT
GRATING PLAN VIEW - EL 13.500m(TOS) GRATING PLAN VIEW - EL 15.500m(TOS) BARRY - BIOMASS UK No 2 LLP
TITLE
TURBINE PLATFORM
FABRICATION DRAWING
SCALE DRAWING SIZE DRAWN
1:25 A1 ES/MU
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0
527
686 164 435
521
609 525 1000 715 530 DO NOT SCALE - IF IN DOUBT ASK
257 485
NOTES
138
138
188
188
188
188
R120
288
R120
GENERAL NOTES:
353
85 R170 R120
TYP
755
340
335
240
240
240
240
621
621
621
621
137 126
651
133
170
85 170 500 1. Do not scale from this drawing.
R170
178 187 2. All dimensions are in millimetres(mm) and all levels are in
275
42 257 183
192 metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
280
280
280
280
280
1693
85
1693
discrepancies should be reported to GHD LIVIGUNN.
4. This drawing is to be read in conjunction with relevant project
1985
1985
1985
1985
1985
1985
1985
1340
134 136
950
1427
1422
1557
1557
1557
1557
960
6. Pipe supports on hold.
85
1084
1084
1084
1084
1054
85
STEELWORK:
85 170 500
1. All works are to be carried out in accordance with the
85
85
485 325 170 355
recomendation of the of the national structural steelwork
850 specification (NSSS) Fifth Edition 2010, CE Marking Version.
435 429 92 2. All hot rolled general steelwork and base plates to be grade
84 170 271
85
85
1000 39 170 506 S355JR to BS EN 10025-2. All structural hollow sections to be
485 530
68 541 grade S355JRH to BS EN 10210-2.
609
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
GRATING-01 GRATING-02 GRATING-03 GRATING-04a GRATING-04b GRATING-05 GRATING-06 GRATING-07 GRATING-08 GRATING-09 GRATING-10 BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
678 85 1175 1175 55 6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
520 170 95 150
bolts
39
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
389
1000 598 402 950
700 1000 680 to be 4mm fillet welds.
132
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
909
170
1000
1000
galvanised coating to be min 85m. Environment category C3 to BS
762
EN ISO 14713-1 and design life of 25 years. The surface protection
185
188
188
70
R120
441
in EN BS 12944:
240
240
53
1330
621
621
651
651
651
990
- For any steel elements inside, not including insulated piping and
144 136 234 lagging: Class C3(Urban and Industrial atmosphere, moderate
236 sulphur dioxide levels and production areas with the high humidity).
91
GRATING-18 GRATING-20 GRATING-22 GRATING-24
2055
234 - For the steel elements in the fuel storage, not including insulated
280
280
and lagging: Class C4(Industrial and coastal chemical processing
280
280
280
plants).
2055
1175 1090 55
1985
1985
1985
1985
- For the outside steel elements, not including insulated piping and
69
170
240 170 255 185 lagging: Class C4(Industrial and Coastal chemical processing plants)
85
175 160 840
1557
1557
98
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
following structure which are defined as EXC3:
999
999
516
Runway Beam
1054
1054
1054
729
95
ON HOLD
170
101
Brackets supporting runway beam
850
80
37
1000
762
Column supporting brackets
722
677
931
24 Horizontal TIE members
85
411
344 170 250
Overhead crane supporting structures
(Turbine building, workshop)
54 170 456 1000 11. Allowance for levelling shims and grout thickness not to be less
121
864 136
85
85
274 170 256 1000 than 15mm and no more than 25mm. May vary for large base plates.
1175
1175 12. Use non-shrink flowable grout fosroc conbextra GP or similar
approved for grouting operatiions. The grout must extend between
120mm and 50mm past the base plates edges.
13. Nominal grout thickness is 25mm u.n.o.
GRATING-11 GRATING-12 GRATING-13 GRATING-14 GRATING-15 GRATING-16 GRATING-17 GRATING-19 GRATING-21 GRATING-23 14. Access platforms, handrails, stairs, ladders shall conforming to:
BS 4952 Grating
BS 5395/EN ISO 14122 Platform, Stairs
41 257 120 245 327 622 170 198 37 170 698
72 268 622 68 BS 8300 Handrails
75
75
To steelway or approved equivalent supplier.
15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
with HIT-V-R Rods, minimum 270mm embedent.
257
909
909
909
919
17
0
17. - Indidacates area on base plate for drilling holes for
245
900
chemical anchors.
900
85
1385
1385
1385
1385
113
1385
1385
1375
87
762
762
762
117 112
R120
115
REFERENCE DOCUMENTS:
240
240
239
220
762
220
R120 R110
R120
246
237
236
236
990 990 990 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
180
170
R120
- C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
690 990 - BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
990 340 500 990 905
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
GRATING-25 GRATING-26 GRATING-27 GRATING-28 GRATING-29 GRATING-30 GRATING-31 GRATING-32 GRATING-33 GRATING-34 Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
Plan El 13.500
915 50 950 855 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
0 865 50 914 1000 340 157 153 195 Sections A, B, P, R
50
50
43
43
538 140 0 990 780
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
0
137
137
262
262
165 165
R145 Hall Sections E, F, G
546
546
290
290
75
854
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
839
340
340
1158
950
1353
1353
1251
1251
1251
1251
140
1151
1151
160
160
1303
1303
0
R170 R170
R80 Revision
0
110
724
724
606
606
495
495
0
HANGER 5 & 6, BONA ROAD
390
0
50
50
85
GRATING-35 GRATING-36 GRATING-36a GRATING-37 GRATING-38 GRATING-39 GRATING-40 GRATING-41 GRATING-42 GRATING-43 GRATING-44 GRATING-44a
CLIENT
84 916 990 780
75
1015 1015
1015 1153
733 1015 1153 PROJECT
142
178
543
1212
30
420
383
236
1138
750
590
30
790
990
790
168
TITLE
TURBINE PLATFORM
97
855 160
64
FABRICATION DRAWING
109
97
1015 1153 metres(m) AOD, unless noted otherwise.
3. All Dimensions and levels to be checked on site and any
discrepancies should be reported to GHD LIVIGUNN.
340
340
59
340
5 4. This drawing is to be read in conjunction with relevant project
97
standards and specification.
990
990
314
314
990
85
956
1000
990
956
314
6. Pipe supports on hold.
1000
859
990
990
990
163 172
163 172
STEELWORK:
163 172
85
1. All works are to be carried out in accordance with the
1153 1010 5 recomendation of the of the national structural steelwork
44
44
specification (NSSS) Fifth Edition 2010, CE Marking Version.
44
15 1079 59 2. All hot rolled general steelwork and base plates to be grade
S355JR to BS EN 10025-2. All structural hollow sections to be
grade S355JRH to BS EN 10210-2.
3. Connection design in accordance to BS-EN-1993-1-8. Base plates
and Holding Down Bolts designed by client. Details to be confirmed
by civil contractor.
4. Steel overhead runway beams shall be tested in accordance with
GRATING-55 GRATING-56 GRATING-57 GRATING-58 GRATING-59 GRATING-60 GRATING-61 GRATING-62 GRATING-63 BS 1993-6 and BS 2853.
5. All Connections forces shown are U.L.S. value.
6. Connections shall have a minimum of 2 no M16 Grade 8.8 bolts.
Beams and rafters shall have a minimum of 4 no. M16 Grade 8.8
bolts
7. Grade 8.8 bolts to be in accordance with BS 3692, BS EN ISO 4014.
8. All welds to be minimum 6mm continous fillet welds u.n.o. seal welds
to be 4mm fillet welds.
9. Steelwork to be galvanised to BS EN ISO 1461. Thickness of
galvanised coating to be min 85m. Environment category C3 to BS
EN ISO 14713-1 and design life of 25 years. The surface protection
10 - VARRIES 10 classification shall be as follows conforming to the classes defined
in EN BS 12944:
Q5 - For any steel elements inside, not including insulated piping and
215 lagging: Class C3(Urban and Industrial atmosphere, moderate
sulphur dioxide levels and production areas with the high humidity).
110- DET. 1a 105 - DET. 1a - For the steel elements in the fuel storage, not including insulated
FB 100x10 88 - DET. 1c 128 - DET. 1c and lagging: Class C4(Industrial and coastal chemical processing
COAMING plants).
- For the outside steel elements, not including insulated piping and
50
22 22 (25 NOS) lagging: Class C4(Industrial and Coastal chemical processing plants)
48
10. Execution class is defined as EXC2 to BS EN 1090-2. Except for the
GTG 25x5 N100 (30/100) TYP following structure which are defined as EXC3:
SAFEGRID 100
Runway Beam
Brackets supporting runway beam
Column supporting brackets ON HOLD
25
BS 8300 Handrails
IWO GRATING PENETRATION To steelway or approved equivalent supplier.
Scale 1:3 Q5 15. Bolt type and embedent to be M24 HILTI HIT 200A chemical anchor
22 22 with HIT-V-R Rods, minimum 270mm embedent.
41 16. Over material (O.M.) to be cut and cut out to be applied after final
dimension check.
17. - Indidacates area on base plate for drilling holes for
chemical anchors.
GRATING
REFERENCE DOCUMENTS:
- KEY PLAN - BARRY_01_DWG_23_20700
BASE PLATE (2 NOS) 22 - BASE PLATE DETAILS - BARRY_01_DWG_23_20750
50
- C & S REPORT (REP) - BARRY_01_20076
- C & S REPORT (REP) - BARRY_01_20077
- BARRY_01_DWG_07_20727 - Steelwork Arrangment Turbine Hall
155 100 110
Plan El 10.400m
- BARRY_01_DWG_07_20728 - Steelwork Arrangment Turbine Hall
365 Plan El 10.400m
- BARRY_01_DWG_07_20729 - Steelwork Arrangment Turbine Hall
DETAIL 1b Plan El 13.500
TYP GRATING FIXATION Mirror for detail 1d Q5 - BARRY_01_DWG_07_20730 - Steelwork Arrangement TurbineHall
N.T.S. Sections A, B, P, R
- BARRY_01_DWG_07_20731 - Steelwork Arrangment Turbine Hall
Sections C, D.
- BARRY_01_DWG_07_20732 - Steelwork Arrangement Turbine
Hall Sections E, F, G
A0 24-08-2017 ISSUED FOR REVIEW ES/MUMM/RK SM
HANDRAIL POST
Rev Date Description By Chk App
GRATING Revision
10
30 95 35 129
TYP
25
C15 CLIENT
40
50
~10~
70
103
100
30
78
20
22 (29 NOS)
R8
15 PROJECT
41
258 30
BARRY - BIOMASS UK No 2 LLP
TITLE
TURBINE PLATFORM
TYP STAIRTREAD DETAILS FABRICATION DRAWING
FOR STAIRCASE SECTION Q5-Q5 SCALE DRAWING SIZE DRAWN
15 Nos. 1:25 A1 ES/MU
Scale 1:3 Scale 1:3
DRAWING No. REV.
XXX-XXX-XXX-XXX-XXX A0