Professional Documents
Culture Documents
1
Code No: R41034 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
UN CONVENTIONAL MACHINING PROCESSES
(Mechanical Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
1 How will you analyze the applicability of different processes to different types of
materials, namely metals, alloys, and non metals? Presentation in the form of a
table is preferred. [15]
3 a) Draw the schematic layout of abrasive jet machine and explain its operational
characteristics. What are the methods adopted to have an effective control over
the mass flow rate of the abrasive. [10]
b) What are the applications of water jet machining [5]
4 a) How will you carry out the analysis for optimization of metal removal rate in
EDM process? [8]
b) What are the functions of dielectric fluid used in Electric Discharge Machining? [7]
5 a) Discuss in detail about the thermal features of LBM and explain the construction
and working of LBM. [10]
b) Distinguish between the electron beam machine and laser beam machine [5]
6 a) Explain metal removal mechanism in Plasma Arc machining with neat sketch. [8]
b) Can you machine electrically non conductive materials by PAM? Justify your
answer. [7]
7 Explain with neat sketch, working of Electro stream drilling and discuss their
advantages, limitations and applications. [15]
1 of 1
WWW.MANARESULTS.CO.IN
|''|''|||''|'''|||'|
Set No. 2
Code No: R41034 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
UN CONVENTIONAL MACHINING PROCESSES
(Mechanical Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
1 What are the basic limitations of conventional machining process? Justify the
need of unconventional machining process in todays industries. [15]
3 a) Write short notes on material removal rate and wear rate of nozzle in WJM. [8]
b) Explain how material is removed in AWJM. [7]
4 a) In chemical machining, what are the factors by which the selection of etchants
is governed. [7]
b) In an ECM process for machining iron it is desired to obtain a metal removal
rate of 1cm3/min. Determine the amount of current required for the process.
Assume that Atomic weight of iron = 56 gram, Valency at which dissolution
occurs= 1.3, Density of iron = 7.8 gm/cm3 and faradays constant= 1609 amp-
min. [4]
c) Write limitations of Electro chemical machining. [4]
5 Explain in detail about the positioning system, wire drive system, power
supply, and dielectric system of wire cut EDM. Also discuss its process
parameters and their effects. [15]
6 a) Briefly explain the population inversion between energy levels with respect
to the laser beam machining. [8]
b) Explain process parameters, advantages and limitations of Electron beam
machining. [7]
7 a) Explain the parameters that are affecting the performance of plasma arc
machining. [5]
b) What is non transferred and transferred mode of plasma arc and explain their
mechanism of material removal. [10]
1 of 1
WWW.MANARESULTS.CO.IN
|''|''|||''|'''|||'|
Set No. 3
Code No: R41034 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
UN CONVENTIONAL MACHINING PROCESSES
(Mechanical Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
1 Explain the need for the development of unconventional machining process by
considering any four simple cases of your own interest. [15]
5 Explain the following in Electric discharge machining (EDM) with neat sketch:
i). Electrode feed control system
ii). Factors to be considered for EDM machine tool selection [15]
7 a) Discuss the process parameters that influence on the quality of the cut in PAM. [8]
b) List applications of plasma in manufacturing industries. [7]
8 a) Explain in detail about applications of shaped tube electrolytic machining. [8]
b) Explain working of abrasive flow finishing with neat sketch. [7]
1 of 1
WWW.MANARESULTS.CO.IN
|''|''|||''|'''|||'|
Set No. 4
Code No: R41034 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
UN CONVENTIONAL MACHINING PROCESSES
(Mechanical Engineering)
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
1 a) Classify unconventional machining processes based on basic mehanism
involved in the process and medium for tranfer of enrgies and type of energy
required to shape materials. [10]
b) Is uncoventional machining process an alternate or complement to conventional
machining process?Justify. [5]
2 a) Briefly discuss about the mechanisms involved in material removal using USM. [9]
b) Explain various tool feed mechanisms used in USM. [6]
3 a) Explain the working principle of Water jet Cutting with neat sketch. [8]
b) Material removal rat in AJM is 0.5 mm3/sec. calculate MRR/impact if the
mass flow rate of abrasive is 3gm/min, density is 3 gm/CC and grit size is
60 microns . Also calculate the indentation radius. [7]
5 a) What are the different types control circuits used in EDM Process. [10]
b) What are the basic requirements of tool materials in EDM process? Name any
four tool materials. [5]
6 Describe the electron beam machining process with a simple sketch and write
about its process parameters, advantages, and applications. [15]
7 a) How MRR could be effect on surface finish and Accuracy in PAM. [8]
b) List the applications plasma in machining. [7]
1 of 1
WWW.MANARESULTS.CO.IN
|''|''|||''|'''|||'|