You are on page 1of 4

Module PE5

Problem 1
Vt R T
Recall that the speed of a DC motor is given by w a 2 . A particular separately excited DC
k k
motor has k 1.44 , R a 0.86 . When it is operating at 150 rad/sec, the armature current is
I a 40 A . The terminal voltage Vt is held constant under all conditions.

(a) Compute Vt
(b) Compute the no-load speed in rad/sec

Solution to problem 1
(a) E a kwm 1.44 150 216V
Vt E a I a ra 216 40 0.86
250.4V
Vt RT V
(b) "No load" speed occurs when T=0 (No load !), therefore, w a 2 t when T=0
k k k
250.4
w 173.9rad / sec
1.44

Problem 2
A separately excited DC motor runs at 100 rpm supplying rated torque when the applied voltage is 50 volts
and the armature current is 10A. The armature resistance is Ra = 1 ohm. A thyristor- controlled chopper
circuit is used to decrease the applied voltage to 40 volts, at constant field flux, to drive a load at 75% of
the rated torque. The conducting time Ton of this circuit is fixed at 0.2 seconds. Compute the speed of the
motor at 40 volts and the blocking time Toff of the chopper circuit.

Solution to problem 2

T1 k I a1
T2 0.75T1 k I a 2 0.75(k I a1 ) I a 2 0.75I a1 (0.75)(10 A) 7.5 Amps
E a1 Vt1 I a1 Ra 50 (10)(1) 40Volts
E a 2 Vt 2 I a 2 Ra 40 (7.5)(1) 32.5Volts
E a1 E a 2 E 32.5
E a1 k 1 , E a 2 k 2 2 a 2 1 (100) 81.25rpm
1 2 E a1 40
Ton VLoad , DC 0.2 40
Toff 0.05 sec onds
Ton Toff V 0.2 Toff 50
Problem 3
A separately excited D.C motor is rated for a full load torque of 100Nm. For an applied voltage of 240V
and for flux ( ) per pole of 30 mWb, the no-load and full load speeds of the motor are 1595 r.p.m and
1195 r.p.m respectively.

Find
a) i) The constant k
ii) The armature resistance Ra
b) If the applied voltage and the flux per pole are reduced to 200V and 20mWb respectively,
Find
i) The corresponding no load speed
ii) The corresponding full load speed

Solution to problem 3
Vt RT
a 2
a) From the text, we know k (k ) that . From the problem, we have:
T full load 100 Nm Vt 240V 30mWb n no load 1595rpmn full load 1195 rpm

At no load,
1595rev 1 min 2rad
T 0and no load 167.03rad / sec
min 60 sec rev
V Vt 240
167.03 t k 47.9
k (167.03) (167.03)(0.03)

At full load,
TFL 100 Nm 2
FL (1195) 125.1rad / sec
60
V R T ( k ) 2 Vt
125.1 t a FL2 Ra 125.1
k ( k ) TFL k
((47.9)(0.03))
2
240
Ra 125.1 0.865
100 (47.9)(0.03)

b) Vt = 200 V, = 0.02 Webers.


Vt 200 60
noload 204.08rad / sec n NL 204.08 1949.8rpm
k (49)(0.02) 2
V RT 0.865(100)
full load t a 2 204.08 88.265rad / sec
k (k ) [(49)(0.02)]2
60
n FL 88.265 843.3rpm
2
Problem 5
An engineer wants to construct a half-wave rectifier for speed control of a DC motor using a thyristor, but
there is no gate-pulse circuit available. The implication is that he/she can supply no gate pulse. Without a
gate pulse circuit, can the engineer just use the thyristor like a diode, so that at least the circuit can supply
one DC voltage level to make the motor run at a single speed? Indicate yes or no, and identify the
feature(s) of a thyristor that support your answer.

Solution to problem 5
Answer 1: No, it cannot be done, because without the gate pulse, the thyristor will not be able to turn on
and it will appear as open-circuit at all times.

Answer 2: Yes, it can work if the applied AC voltage has a peak that is significantly higher than the
forward breakover voltage of the thyristor.

Problem 6
A square wave voltage waveform having a period of 2 seconds is applied through a half wave thyristor-
controlled rectifier circuit to the armature terminals of a separately excited DC motor driving It is known
that the DC motor has k=1.44 (a constant under all conditions), and Ra=0.86 ohms. When Ia=40 amperes,
the speed is 150 rad/sec. The source voltage and the thyristor firing time is shown in the figure below.
(a) Draw this circuit, including the rectifier and the motor.
(b) What is the effective DC voltage at the motor armature terminals under this condition ?
(c) What is the peak value of the square wave under this condition ?

Vsource

Time (sec)
0.5 1 2

Fire thyristor

Solution to problem 6

a) Ia

V(t) Ra
_
Ea
b) Ea = k = (1.44)(150) = 216, Vt = 216 + IaRa = 250.4 Volts

c) 1
2 1
1 1
Vdceff
T 0
V (t ) dt V (t ) dt V 250.4 V 1001.6Volts
2 0. 5 4

You might also like