Professional Documents
Culture Documents
Page 1 of 5
Description
On January 16, 2012, the S4 part number was modified. The S4 optical encoder
is now offered with a differential output option; as a result, the S4 part number
was changed to accommodate either the single ended or differential output
options. The S4 part number also has a place holder added for a possible future
index option. The index option is currently not available and there is not a
projected date at which it will be made available. The current "Power" option for
the S4 was also removed from the part number. The power option is very rarely
selected and therefore is being eliminated from the S4 part number.
The S4 encoder is available with ball bearings for motion control applications, or
static drag to feel like a potentiometer for front-panel manual interface. Features
The reflective sensor incorporates an LED light source and a monolithic photo Miniature size
detector with signal shaping electronics, providing two channel bounceless Low High retention snap-in polarized connector
quadrature TTL outputs. Tracks from 0 to 30,000 cycles/sec
Ball bearing option tracks up to 10,000 RPM
The S4 can be connected by using a high retention 4 conductor snap-in Wide operating temperatures
polarized 1.25mm pitch connector. The mating connector is polarized and should 100 to 360 cycles per revolution (CPR)
attach smoothly to the encoder; do not force. See below for Cables & 400 to 1440 pulses per revolution (PPR)
Connectors. 2 channel quadrature TTL squarewave outputs
Rev. 160509133914
S4 Miniature Optical Shaft Encoder
Page 2 of 5
S4 Differential
S4 Single Ended
Rev. 160509133914
S4 Miniature Optical Shaft Encoder
Page 3 of 5
Environmental
Parameter Value Units
Vibration (5Hz to 2kHz) 20 G
Operating Temperature -20 to 100 C
Electrostatic Discharge, IEC 61000-4-2
Single-ended (S-option) 3 kV
Differential (D-option) 15
Mechanical
Specification Sleeve Bushing Ball Bearing
Max. Acceleration 10000 rad/sec 250000 rad/sec
Max. Shaft Speed 100 rpm 15000 rpm
Max. Shaft Torque 0.5 0.2 in-oz (D-option) 0.05 in-oz
0.3 in-oz (N-option)
Max. Shaft Loading 2 lbs. dynamic 1 lb.
20 lbs. static
Bearing Life > 1,000,000 revolutions L10 = (22/Fr) *
Where L10 = bearing life in millions of revs, and
Fr = radial shaft loading in pounds
Weight 0.46 oz. 0.42 oz.
Max. Shaft Total Indicated Runout 0.0015 in. 0.0015 in.
Max. Panel Nut Tightening Torque 20 in-lbs 20 in-lbs
Technical Bulletin TB1001 - Shaft and Bore Tolerances Download
Phase Relationship
Rev. 160509133914
S4 Miniature Optical Shaft Encoder
Page 4 of 5
(1) B leads A for clockwise shaft rotation, and A leads B for counterclockwise rotation viewed from the shaft side of the encoder.
(2) Typical values represent the encoder performance at typical mounting alignment, whereas the maximum values represent the
encoder performance across the range of recommended mounting tolerance.
Single-ended Electrical
Differential Electrical
Pin-out
4-pin Single-ended (1) 6-pin Differential (2)
Pin Description Pin Description
1 +5VDC power 1 Ground
2 A channel 2 A channel
3 Ground 3 A- channel
4 B channel 4 +5VDC power
5 B channel
6 B- channel
Rev. 160509133914
S4 Miniature Optical Shaft Encoder
Page 5 of 5
Ordering Information
S4 - - - - -
CPR Shaft Index Output Torque
100 = 125 =1/8" diameter N =No Index S =Single Ended D =Default
108 = 236 =6mm diameter D =Differential B =Ball Bearing
120 = 250 =1/4" diameter N =Light Static Drag
125 =
128 =
200 =
250 =
256 =
300 =
360 =
Notes
For ordering information please see the Compatible Cables / Connectors section above.
US Digital warrants its products against defects in materials and workmanship for two years. See complete warranty for details.
Rev. 160509133914