Professional Documents
Culture Documents
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.12.8 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 8/3/2015
Specifier's comments:
Geometry [mm]
plan view section A z
y x
t=12
h ef =170 2.000
>10h ef
lx = 340
section B
x
1020
section B
z
y
>10h ef
h = 880
section A
Loading
Design loads [kN, kNm]
Resulting loads [kN, kNm]
N 0.00
Vx 0.00
Vy -200.00
Mx 400.00
My 0.00
Mz 0.00
Eccentricity (structural section) [mm]
ex = 0 ; e y = 294
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company: Page 2 of 6
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.12.8 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 8/3/2015
Tension load
Steel failure
h h
N Rk,s [kN ] M,s N Rd,s [kN ] N Sd [kN ]
112.65 1.500 75.10 53.39
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company: Page 3 of 6
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.12.8 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 8/3/2015
Pull-out failure
h h
N Rk,p [kN ] c M,p N Rd,p [kN ] N Sd [kN ] deeper setting
113.18 1.217 1.800 152.99 53.39 2.000
Splitting failure
2 0 2
A c,N [mm ] A c,N [mm ] c cr,sp [mm ] scr,sp [mm ] deeper setting
581400.0 115600.0 170 340 2.000
Shear load
Pryout failure
2 0 2
A c,N [mm ] A c,N [mm ] c cr,N [mm ] scr,N [mm ] k-factor deeper setting
693600.0 115600.0 170 340 2.000 2.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company: Page 4 of 6
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.12.8 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 8/3/2015
(N + V ) / 1.2 <= 1
Edge reinforcement
Edge reinforcement is not required to avoid splitting failure
No edge reinforcement is required to assure characteristic shear resistance against concrete edge failure
Displacements
The displacement of the highest loaded anchor should be calculated according to the relevant approval. The displacement due to
hole tolerances can be neglected, because this method assumes filled holes (Hilti Dynamic Set). The characteristic loads of the
highest loaded anchor are
h
N Sk = 39.55 [kN]
h
V Sk = 13.47 [kN]
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Warnings
An even load distribution of the shear load is assumed, e.g. by using the Hilti Dynamic Set.
The compliance with current standards (e.g. EC3) is the responsibility of the user
Dry hole and standard cleaning are assumed! Temperature influence is neglected!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company: Page 5 of 6
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.12.8 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 8/3/2015
150.0
21 22
19 20
17 18 620.0
294.0
15 16
13 14
x
11 12
9 10
7 8
620.0
5 6
3 4
70.0
1 2
85.0 85.0
170.0 170.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company: Page 6 of 6
Specifier: Project:
User application Address: Contract No.:
PROFIS Anchor 1.12.8 Phone/Fax: - / - Responsible:
http://www.hilti.com/ E-Mail: Location/Date: - / 8/3/2015
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan