Professional Documents
Culture Documents
LatticeECP3 Family
The LatticeECP3™ FPGA family is the
newest addition to the value-based
LatticeECP™ (Economy Plus) FPGA
series. LatticeECP3 offers up to 150K
LUTs of logic capacity and up to 7Mbits
of memory for system integration,
cascadable high performance DSP
blocks for processing intensive RF/
IF and baseband designs, support for
high-speed memory interfaces including
DDR3 at 800Mbps and up to 1Gbps
generic LVDS performance for ADC/DAC
interfacing.
In This Issue:
Audio/Video
Gennum
Battery Management
Linear Technology
Bus Interface
Exar
DC/DC Controllers
Linear Technology
LED Drivers
Micrel
Linear Regulators
Linear Technology
Logic
Lattice Semiconductor
Memory
GSI Technology
Microcontrollers
Digi
Modules
Digi
Power Management
Exar
Signal Integrity
Vitesse
TFT-LCD
Optrex
Wireless
connectBlue
APAC Edition
August 2010
GS2994/GS2993…these are not just any
SD/HD/3G-SDI Adaptive Equalizers
Audio / Video
The GS2994 and GS2993 are high-speed BiCMOS integrated circuits designed to equalize and restore signals received over 75Ω coaxial cable. The devices
are designed to support SMPTE 424M, SMPTE292M and SMPTE 259M, and is optimized for performance at 270Mb/s, 1.485Gb/s and 2.97Gb/s. The GS2994
and GS2993 feature DC restoration to compensate for the DC content of SMPTE pathological test patterns.
The Carrier Detect output pin (CD) indicates whether a valid input signal has been detected. It can be connected directly to the SLEEP pin to enable automatic
power-down upon loss of carrier. A voltage programmable threshold, which can be changed via the SQ_ADJ pin, forces CD high when the input signal
amplitude falls below the threshold. This allows the GS2994 and GS2993 to distinguish between low-amplitude SDI signals and noise at the input of the
device.
The equalizing and DC restore stages are disengaged when the BYPASS pin is HIGH. No equalization occurs in Bypass mode. The GS2994 and GS2993 include
a gain selection pin (GAIN_SEL) which, when tied HIGH, compensates for 6Db flat attenuation. The differential outputs can be DC-coupled to Gennum 3.3V
cable drivers and reclockers and to industry-standard 1.2V, 2.5V and 3.3V using the VCC_O pin for the GS2994 and the OP_CTL pins for the GS2993.
Features
SMPTE 424M, SMPTE 292M and SMPTE 259M compliant
Automatic cable equalization
Multi-standard operation from 143Mb/s to 2.97Gb/s
Performance optimized for 270Mb/s, 1.485Gb/s and 2.97Gb/s. Typical
equalized length of Belden 1694A cable:
140m at 2.97Gb/s
200m at 1.485Gb/s
400m at 270Mb/s
Supports DVB-ASI at 270Mb/s
Manual bypass (useful for low data rates with slow rise/fall times)
Programmable carrier detect with squelch threshold adjustment
Automatic power-down on loss of signal
Standby power <30mW (typical)
Differential outputs support DC-coupling to 1.2V, 2.5V and 3.3V CML logic
0/6 dB gain boost selection pin
Selectable de-emphasis: 2dB, 4dB and 6dB
Standard EIA/JEDEC logic control and status signal levels
Single 3.3V power supply operation
Power consumption is typically 160mW
Wide operating temperature range of -40ºC to +85ºC
Small footprint 16 pin QFN package (4mm x 4mm)
Applications
Serial routing switchers
Professional video editing equipment
Production and master control switchers
Distribution amplifiers
Broadcast video to Fiber Channel or Gigabit Ethernet transport linecards
Camera control units for medical imaging equipment
2 For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts
B attery Management
LTC4425 - Linear SuperCap Charger with Current-
Limited Ideal Diode and V/I Monitor
Programmable 2A 2-Cell Supercap Charger with Automatic Cell Balancing
in a Compact 9mm2 Package
The LTC®4425 is a constant-current/constant-voltage linear charger
designed to charge a 2-cell supercap stack from either a Li-Ion/
Polymer battery, a USB port, or a 2.7V to 5.5V current-limited supply.
The part operates as an ideal diode with an extremely low 50mΩ
on-resistance making it suitable for high peak-power/low average
power applications. The LTC4425 charges the output capacitors to
an externally programmed output voltage in LDO mode at a constant
charge current, or to VIN in normal mode with a smart charge current
profile to limit the inrush current until the VIN to VOUT differential is
less than 250mV. In addition the LTC4425 can be set to clamp the
output voltage to 4.9V or 5.4V.
Charging 2-Cell Series Supercapacitor from Li-Ion Source Features Charge Current vs VIN to VOUT
50mΩ
0.6 Ideal Diode from VIN to VOUT
VOUT VIN FULL CHARGE CURRENT VFB = VIN
VIN TO HIGH PEAK Smart Charge Current Profile Limits Inrush Current
POWER LOAD 0.5
Li-Ion
Internal Cell Balancer (No External Resistors)
1F
CHARGE CURRENT (A)
1.5M
VMID Programmable
0.4 Output Voltage (LDO Mode)
PFI 1F Programmable VIN to VOUT Current Limit
0.3 CURRENT LIMITED
+ – VIN
BY Monitoring
PMOS RDSONof V to V
FB Continuous IN OUT Current via PROG Pin
1.2M
Low0.2Quiescent Current: 20μA 1/10 CHARGE
470k CURRENT
PFI_RET LTC4425 PFO
VIN Power Fail, PGOOD Indicator
0.1
PROG 2.45V/2.7V IDEAL DIODE
Cell Protection Shunts
IMONITOR FORWARD VOLTAGE = 15mV
SEL 2.45V/2.7V (4.9V/5.4V
0 SuperCap Max Top-Off Voltage)
0 0.2 0.4 0.6 0.8 1
2k
EN 3A Peak Current Limit,
VINThermal
– VOUT (V)Limiting
GND
Tiny Application Circuit, 3mm × 3mm × 0.75mm DFN and
12-Lead MSOP Packages
For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts 3
SP336 - Ultra-Versatile 3.3V/5.0V Single-Chip
RS-232/RS-485/RS-422 Serial Transceiver
B us I nterface
Advanced Features Deliver Maximum Design Flexibility for Rugged Industrial Markets
The SP336 is a highly integrated multiprotocol serial transceiver that contains both
RS-232 and RS-485/422 drivers and receivers. The SP336 can be configured into eight
operating modes including RS-232-only (4Tx/4Rx), RS-485/RS-422-only (2Tx/2Rx) full
or half duplex, two RS-232/RS-485/RS-422 mixed-modes, two shutdown modes and a
diagnostic loop-back mode. All RS-485 receivers feature high input impedance, which
allows up to 256 transceivers on a shared bus. All bus input and output pins are ESD
protected up to +/-15kV IEC 61000-4-2 air-gap and +/-8kV IEC 61000-4-2 contact
discharge.
Features Benefits
Operates from a Single 3.3V or 5V Supply Voltage Best-in-Class 15kV ESD (Air gap) for Rugged Applications in Industrial
Environments
Up to 10 Mbps for RS-485/422 and Up to 1Mbps for RS-232
Slew Rate Control Feature - Up to 250kbps
Re-Configurability into Five Serial Protocol Modes - RS-232 Mode,
+/- 15kV ESD Protection (IEC 61000-4-2, Air-Gap) Full or Half Duplex RS-485/RS-422 Modes, Two Mixed-Modes,Enables
+/- 8kV ESD Protection (IEC 61000-4-2, Contact) Customers to Configure the Serial Port to Meet Many Application Needs
1/8th Load in RS-485 Mode (Max. 256 Transceivers on
the Communication Bus) Selectable Slew Rate Controlled Outputs Minimize Problems with
Reflections and Ringing on Long or Un-Terminated Cables
Advanced Failsafe Feature (RS-485/422 mode)
Diagnostic Loop Back Function
Driver Short-Circuit Protection Thermal Shutdown Overload
Protection
Applications
Factory Automation Equipment
Security Networks
Industrial/Process Control Networks
Point-of-Sales Equipment
Gaming Machines
Serial Protocol Translators (ex. RS-232 to RS-485/422)
Embedded Industrial PC’s
Building Environmental Control Systems (ex. HVAC)
Cable Repeaters / Port Extenders/ Hubs
4 For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts
LTC3865 - Dual, 2-Phase Synchronous DC/DC
D C /D C C ontroller
Controller with Pin Selectable Outputs
1% Accurate Pin-Selectable Output Voltages
60
SW1 SW2 POWER LOSS
LTC3865 50
BG1 BG2
40
PGND 0.1
30
100 FREQ 100
SENSE1+ SENSE2+ 20
2m 1000pF 1000pF 2m 10
SENSE1– SENSE2– 0 0.01
100 VID11 VID21 100 0.01 0.1 1 10 100
VOUT1 VID12 VID22 VOUT2 LOAD CURRENT (A)
1.5V VOSENSE1 VOSENSE2 1.2V
15A + ITH1 ITH2 + 15A
COUT2,3 1000pF TK/SS1 SGND TK/SS2 1000pF COUT5,6
Features Applications
Dual, 180° Phased Controllers DC Power Distribution Systems
2-Pin VID Output Voltage Programming from 0.6V to 5V
High Efficiency: Up to 95%
RSENSE or DCR Current Sensing
Phase-Lockable Fixed Frequency 250kHz to 770kHz
Adjustable Current Limit
Dual N-Channel MOSFET Synchronous Drive
Wide VIN Range: 4.5V to 38V Operation
Adjustable Soft-Start Current Ramping or Tracking
Output OV Protection With Reverse Current Limit
Power Good Output Voltage Monitor
32-Pin 5mm × 5mm QFN and 38-Lead TSSOP Packages
For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts 5
MIC3201 - High Brightness LED Driver
The MIC3201 is a hysteretic step-down, constant-current, High-Brightness LED
LED D rivers
The MIC3201 operates with an input voltage range from 6V to 20V. The hysteretic control gives good supply
rejection and fast response during load transients and PWM dimming. The high-side current sensing and
on-chip current sense amplifier delivers LED current with ±5% accuracy. An external high-side current
sense resistor is used to set the output current.
The MIC3201 offers a dedicated PWM input (DIM) which enables a wide range of pulsed dimming. A high
switching frequency operation up to 1MHz allows the use of smaller external components minimizing
space and cost.
The MIC3201 operates over a junction temperature range of -40°C to +125°C and is available in an 8-pin
ePad SOIC package.
Features Benefits
6.0V to 20V input voltage range The first in a family of HB LED Driver products spanning a variety of
High efficiency (>90%) current ranges
± 5% LED current accuracy Provides Constant Current even with changes in input voltage and
High-side current sense output load (diff. # of LEDs)
Dedicated dimming control input Input Voltage range from 6V to 20V
Hysteretic control (no compensation!)
Switching Frequency adjustable upto 1MHz
1A internal power switch
Up to 1MHz switching frequency Integrated 1A (Current limit at 1.2A) Power Switch
Adjustable constant LED current PWM Dimming
5V on board regulator Efficiency > 90%
Over temperature protection
High side current sense capability
–40°C to +125°C Junction temperature range
Thermally enhanced SOIC package Ease of use with no compensation and low parts count
Applications
Broad range of Applications for all regions
MR-16 Bulbs
Garden Pathway Lighting
Under Cabinet Lighting
Street Lighting
Emergency Vehicle Lighting and Signals
Loosely regulated 12V Systems
Channel Letters
Constant Current Power Supplies
6 For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts
LT3032 - Dual 150mA Positive/Negative Low Noise
Linear R egulator
Low Dropout Linear Regulator
Dual Positive/Negative ±20VIN ±150mA LDO Offers 20µVRMS
The LT®3032 is a dual, low noise, positive and negative low dropout
voltage linear regulator. Each regulator delivers up to 150mA with a
typical 300mV dropout voltage. Each regulator’s quiescent current is
low (30μA operating and <3μA in shutdown) and well-controlled in
dropout, making it an excellent choice for battery-powered circuits.
The LT3032 is available in a unique low profile 14-lead 4mm × 3mm × 0.75mm DFN package with exposed backside pads for each regulator, allowing
optimum thermal performance.
Features
Dual Polarity Low Noise 150mA Power Supply 10Hz
Low Noise: 20μV to 100kHz Output Noise
RMS (Positive) and 30μVRMS (Negative)
Low Quiescent Current: 30μA/Channel
LT3032 5V OUT AT 150mA
INP OUTP 20µVRMS NOISE Wide Input Voltage Range: ±2.3V to ±20V
5.4V TO 768k OUTP 20µVRMS
20V ADJP 0.01µF Output Current: ±150mA
100µV/DIV
10µF 10µF Low Shutdown Current: <3μA Total (Typical)
<0.25V = OFF 249k
SHDNP
>2V = ON
BYPP
Low Dropout Voltage: 300mV/Channel
GND Adjustable
OUTN Outputs from ±1.22V to ±20V 30µVRMS
BYPN 100µV/DIV
No Protection Diodes Needed
SHDNN
10µF 249k 10µF Stable with 2.2μF Output Capacitors
ADJN 1mS/DIV 3032 TA02a
OUTN 30µVRMS
100µV/DIV
OUT AT –150mA
RMS NOISE
For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts 7
LatticeECP3 Family
Exceptional Performance – Uncommon Value
The LatticeECP3™ FPGA family is the newest addition to the value-based LatticeECP™ (Economy Plus) FPGA series. LatticeECP3 offers up to 150K LUTs of
Logic
logic capacity and up to 7Mbits of memory for system integration, cascadable high performance DSP blocks for processing intensive RF/IF and baseband designs,
support for high-speed memory interfaces including DDR3 at 800Mbps and up to 1Gbps generic LVDS performance for ADC/DAC interfacing. LatticeECP3 devices
enable you to further reduce cost with built-in high speed, low power transceivers for protocols including PCI Express, Ethernet (GbE, SGMII & XAUI), SDI (3G/
HD/SD), Serial RapidIO, CPRI and OBSAI. LatticeECP3 devices also provide enhanced FPGA configuration options supporting encryption, dual-boot capability and
fast configuration via parallel Flash.
High-Speed I/O
Pre-engineered DDR3 memory (800Mbps)
1Gbps LVDS
On-chip termination
8 For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts
LatticeXP2 Family
flexiFLASH: Instant-On, Secure, Single-Chip FPGA
Logic
LatticeXP2™ devices combine a Look-up Table (LUT) based FPGA fabric with Flash non-volatile
cells in an architecture referred to as flexiFLASH™. The flexiFLASH approach provides a single
chip solution with benefits such as instant-on operation, on-chip storage featuring FlashBAK™
embedded block RAM backup, access to general-purpose Serial TAG memory and inherent design
security. LatticeXP2 devices also support Live Update field reconfiguration with TransFR™, 128-bit
AES bitstream encryption and Dual Boot technologies.
The LatticeXP2 FPGA fabric utilizes an underlying LatticeECP2™ architecture that was optimized
from the outset with high performance and low cost in mind. LatticeXP2 devices support 4-input
LUT-based logic, distributed and embedded memory, Phase Locked Loops (PLLs), pre-engineered
source synchronous I/O and enhanced sysDSP™ blocks.
For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts 9
SigmaQuad-IITM and SigmaDDR-IITM SRAMs
GSI Technology now offers the highest density Type-II+
devices designed for higher speeds
Mem ory
By offering a 144Mbit density SRAM, GSI provides a memory upgrade path for 72Mbit designs. Existing SRAM memory
controllers can be reused with 144Mbit densities, which make for an easy design decision. With the simple addition of
an address signal you get double the density. The same package is used for both the 72Mbit and 144Mbit—15 mm x 17
mm 165 FBGA—which eliminates any footprint issue.
The 144Mbit family of SigmaQuad-II+ and SigmaDDR-II+ SRAMs achieve higher operating frequencies, in part, because they are designed with a longer
read pipeline. When described in terms of cycles of latency, Type-II SRAMs demonstrate a 1.5 cycle read latency, while Type-II+ SRAMs are offered with read
latencies of either 2.0 or 2.5 cycles. The multiple read latency selections allow designers more flexibility to optimize SRAM performance in their particular
applications. Type-II+ SRAMs also offer optional On-Die Termination (ODT) to improve signal integrity. ODT can be enabled or disabled via the ODT pin—a low
(0) disables ODT while a high (1) enables ODT.
Density Type Burst RL Speed Width Part Number
GSI offers both leaded packages for those designs that
8 GS81302D07E/GE-xxx
have not transferred to green manufacturing processes and
RoHS-compliant packages for applications that demand 9 GS81302D10E/GE-xxx
SigmaQuad-II+ 4 2.0 400–300
environmentally friendly products. All devices are offered in 18 GS81302D19E/GE-xxx
Industrial temperature and Commercial temperature ranges. 36 GS81302D37E/GE-xxx
Special testing is available for applications that require wider
8 GS81302T07E/GE-xxx
temperature and voltage limits. For more information, please
visit www.gsitechnology.com. 9 GS81302T10E/GE-xxx
SigmaDDR-II+ 2 2.0 400–300
18 GS81302T19E/GE-xxx
Features 144Mbit
36 GS81302T37E/GE-xxx
8 GS81302D06E/GE-xxx
Highest densities—144Mbit 9 GS81302D11E/GE-xxx
Broadest range of organizations—x8, x9, x18, x36 SigmaQuad-II+ 4 2.5 450–300
18 GS81302D20E/GE-xxx
Highest speeds—up to 333 MHz for Type–II and
450 MHz for Type–II+ 36 GS81302D38E/GE-xxx
On-Die Termination and two Read Latency 8 GS81302T06E/GE-xxx
offerings for Type–II+ products 9 GS81302T11E/GE-xxx
SigmaDDR-II+ 2 2.5 450–300
18 GS81302T20E/GE-xxx
36 GS81302T38E/GE-xxx
Benefits
Focused SRAM supplier providing one stop Density Type Burst Speed Width Part Number
shopping with over 9000 different products 8 GS81302D08E/GE-xxx
ExactPreferenceTM Master die design methodology 9 GS81302D09E/GE-xxx
Short lead times SigmaQuad-II 4 333–167
18 GS81302D18E/GE-xxx
Minimum 7-year product life cycle
FLXDrive-II output impedance control 36 GS81302D36E/GE-xxx
Custom products for application specific designs 8 GS81302Q08E/GE-xxx
9 GS81302Q09E/GE-xxx
SigmaQuad-II 2 250–167
Applications 18 GS81302Q18E/GE-xxx
36 GS81302Q36E/GE-xxx
Networking and Telecom infrastructure
Switches 8 GS81302R08E/GE-xxx
Routers 9 GS81302R09E/GE-xxx
Base stations 144Mbit SigmaDDR-II 4 333–167
18 GS81302R18E/GE-xxx
Common Uses
36 GS81302R36E/GE-xxx
Table look-ups
Statistics accumulation 8 GS81302T08E/GE-xxx
Military 9 GS81302T09E/GE-xxx
Test and Measurement SigmaDDR-II 2 333–167
18 GS81302T18E/GE-xxx
Medical Imaging
36 GS81302T36E/GE-xxx
8 GS81302S08E/GE-xxx
SigmaSIO 9 GS81302S09E/GE-xxx
2 333–167
DDR-II 18 GS81302S18E/GE-xxx
36 GS81302S36E/GE-xxx
10 For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts
ConnectCore Wi-i.MX51 Digi JumpStart Kit
Microcontroller
High-End, Network-Enabled Core Module
Features
High end low power 32-bit System-on Module design
Pre-certified 802.11a/b/g/n wireless LAN interface
On-chip hardware encryption accelerator
Integrated 10/100/(1000) Mbit Ethernet networking
Powerful dual-display and multimedia capabilities
ZigBee® and GPS/3G cellular connectivity support
Complete Microsoft Windows Embedded CE 6.0 and Linux platform
support with full BSP source code
Benefits Applications
Quick time-to-market – fast integration and design flexibility Security and Access Control
Pre-certified module – saving time and money Retail
Industry-leading wireless encryption Digital Signage
Medical
180-Pin Connector Transportation
Security Mul media Memory
2 x U.FL
Industrial / Building Automation
SAHARA v4 OpenGL ES 2.0 + VG1.1 ROM 32KB
(/1000)
Secure JTAG I-Cache D-Cache L2-Cache
PMIC
Ethernet
MAC
Power Mgmt Neon ETM External Memory
Interface
PLL x 3 mDDR 200 MHz
Vector Floa ng DDR2 200 MHz Up to
Clock Reset Point Unit 8 GB Flash
Up to
Fast IrDA Smart DMA 512 MB
AXI / AHB Switch Fabric
DDR2
Accelerometer
1-Wire
180-Pin Connector
For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts 11
New Digi XBee Programmable Module Enables
Custom ZigBee Application Development
Modules
Features:
XBee-PRO ZB Programmable versions using CodeWarrior® development tools allow for easy
customization
8-bit microprocessor brings intelligence to devices
ZigBee mesh networking protocol
Remote firmware updates
Self-healing and discovery for network stability
Little or no configuration needed for out-of-the-box RF communications
Interoperability with ZigBee compliant devices*
*Interoperability requires the ZigBee Feature Set or ZigBee PRO Feature Set to be
deployed on all devices. Contact Digi Support for details.
Benefits:
Common XBee footprint for a variety of RF modules
ZigBee/Mesh 2.4GHz
Embedded ZigBee/Mesh RF modules
External ZigBee/Mesh routers, bridges, adapters
Point-to-Multipoint 900 MHz and 2.4GHz license-free ISM band
Low-power embedded RF modules
Easy-to-use RS-232, RS485/422, USB, and Ethernet external
RF modems
Long Range Point-to-Multipoint / Mesh
1 Watt (30dBm) output power
900 MHz license-free ISM band
Remote Home Control Diagram
Up to 40 miles (64 km) range line-of-site
Applications:
••••••••• Energy
Smart Energy
Alternative Energy
Sensor Monitoring
Building Automation
Lighting Control
Tank-level Monitoring
12 For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts
PowerXR - Evolutionary Solutions for Multi Channel
Power Management
Digital PWM Step Down Controllers
The XRP7704, XRP7708, XRP7713, XRP7714, and
XRP7740, members of the Power XR family, are pulse-
width modulated (PWM) step-down DC-DC controllers
with a built-in LDO for standby power and GPIOs.
The devices provide a complete power management
solution in one IC and are fully programmable via the
included I²C serial interface. Independent Digital Pulse
Width Modulator (DPWM) channels regulate output
voltages and provide all required protection functions Features
such as current limiting and over-voltage protection.
Pin/Function Compatible 4-Channel On Board Standby Power LDO
PWM Controllers On Board Gate Drivers
Each output voltage can be programmed from 0.9V to
XRP7704: 4 x 5A Channels
5.1V without the need of an external voltage divider. Up to 25V Single Input Voltage
XRP7708: 2 x 5A and 2 x 8A Channels
The wide range of the programmable DPWM switching 0.9V Min. Programmable Output Voltage
XRP7713: 3 x 5A Channels
frequency (from 300 KHz to 1.5 MHz) enables the user Independent Channel (re)Configurability
to optimize between efficiency and component size. An XRP7714: 4 x 5A Channels
I²C Controlled
I²C bus interface is provided to program the ICs as well XRP7740: 2 x 5A and 2 x 15A Channels
40-pin QFN and 32-pin QFN (XRP7713 only)
as to communicate with the host for fault reporting Digital Loop Control packages
and handling, power rail parameters monitoring, etc.
The start-up delay and ramp of each PWM regulator Applications
can be independently controlled and offers a complete
Multi Channel Power Supplies
solution for programmable soft-start and soft-stop.
Programmable Power Supplies
Additional information on Exar’s Digital Power Audio- Video Equipments
solutions can be found at www.exar.com/digitalpower Processors and DSP based
or by contacting digitalpower@exar.com. Applications
XRP7704 / XRP7740
Single Input
Voltage Clock
OTP LDO 3.3V/5V LDO
OSC
GPIOs
Port
Digital Gate
FETS
Expansion Supply 1
PWM Driver
I2C I2C
Interface Digital Gate
FETS
Supply 2
Registers
PWM Driver
Power Good
OCP-UVLO
Digital Gate
FETS
Supply 3
PWM Driver
Digital Gate
FETS
Supply 4
PWM Driver
For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts 13
High brightness LED backlit TFT-LCDs for
industrial applications
TFT-LC D
Optrex offers high bright LED-backlit TFT-LCDs for outdoor use that are very well
suited for industrial applications providing excellent performance, product quality,
and long term support
Optrex continues expanding their LED-backlit TFT-LCD offering
and now offers a full line of high bright TFT-LCDs with white LED
for outdoor applications. All the panels are designed for industrial
applications and provide exceptional performance such as: high
bright or super high brightness, high contrast, wide viewing angle,
wide operating temperature range, long LED lifetime, high shock
and vibration tolerance, etc. Many of these displays also incorporate
Natural Color matrix (NCM), a color improving technology, for vivid
color reproduction.
14 For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts
Wireless LAN SPI/SDIO modules for industrial
applications - OWL221a and OWL222a
Wireless
Fully radio type approved, dual-band Wireless LAN modules supporting 802.11abgn
For more information, including pricing, availability, datasheets and samples (if available), please visit http://ap.nuhorizons.com/FeaturedProducts 15
Setting New Standards for Signal Integrity
Solve your signal integrity issues with Vitesse’s advanced IC solutions. With Vitesse’s VScope™
embedded waveform viewing technology, the power to take signals farther, faster is yours.
16
Enhance Your Design...
With Nu Horizons Education and Development Solutions
Portal is a monthly publication containing new products, technologies and development tools
available from Nu Horizons leading suppliers. Portal is availabe both in print and on the web.
Sign up online to receive your copy, be notified of upcoming issues or to request samples of
the products found inside.
http://ap.nuhorizons.com/FeaturedProducts
LabCam delivers online training opportunities in a way that recognizes the value of engineers’
time. As easily as You Tube® videos, engineers can quickly load and watch videos from industry
leaders consisting of insights on products, evaluation kit overviews, end-user applications and
more. Each tutorial is up to ten minutes in length and features technology experts, CEOs and/
or peers introducing new solutions or explaining integral aspects of an important product,
solution or application. This free value-added program is packaged for short, informative and
high quality distance learning.
http://ap.nuhorizons.com/labcam/
Nu Horizons is proud to present our education and training program, which offers engineers
the opportunity to participate in technical seminars conducted by experts focused on the
latest technologies from our leading suppliers. This program provides higher velocity
learning to help minimize start-up time to quickly begin your design process utilizing the latest
development tools, software and products. Check online for the latest seminar schedule.
http://ap.nuhorizons.com/seminars/index.asp
Online Learning Nu Horizons Online Learning Center is designed to provide a complete training experience
for engineers — without having to leave the office. New supplier trainings are posted twice
Center a month and range from new product overviews to in-depth technical training and potential
design implementations. These live trainings are recorded and archived for your viewing
convenience.
www.nuhorizons.com/olc
In order to simplify the design process, Nu Horizons has created a series of application notes
Application designed to guide engineers through the process of interfacing different devices together.
Using a detailed step-by-step approach, these design guides identify key elements in the design
process. Topics in the application notes are organized by design task and each topic is a
Notes stand-alone section, with a short introduction or overview, followed by the step-by-step design
guidelines. All steps include a sufficient level of detail to provide the designer with relevant
information to proceed quickly and easily from start to finish.
www.nuhorizons.com/appnotes
Development Nu Horizons offers a wide range of development / evaluation boards, tools and kits featuring
the latest technology from the most trusted suppliers in the industry. Visit the development
Tools tool section of our website for a variety of solutions all aimed at providing a low-cost solution
for designers to accelerate a product’s time-to-market.
http://ap.nuhorizons.com/development/