Professional Documents
Culture Documents
WWK-861
USER’S MANUAL
2713-2902-108 1
ver. 1.0
Congratulations on your purchase of this WWK-861 multiband amplifier!
I. Application
WWK-861
S1.. S3 - Channel path switches UHF1 ... UHF3 - UHF Antenna inputs
S4 - UHF3 Input bands VHF - VHF Antenna input
(UHF / VHF+UHF)
switch BI/FM - FM Antenna input
P1...P6 - UHF band channel ATT - Attenuator
paths
The WWK-861 amplifier is designed for use in antenna systems receiving terrestrial
analogue and digital TV programs in detached houses, residences, terrace houses,
hotels, boarding houses, holiday centers, schools, hospitals, etc. - even situated in
places with difficult reception conditions, where the received signals have different
levels and are coming from different directions. WWK-861 enables to receive these
signals, to equalize their levels and to amplify them. The WWK-861 amplifier can be
used as an independent unit or as a part of multiswitch system as well as a part of a
simple head-end station (860 MHz system).
2 2713-2902-108
ver. 1.0
II. Amplifier connection and activation
1. Never connect or start the WWK–861 amplifier until the installation of the
receiving antennas has been completed. In order to select the correct antenna type
you should precisely examine the receiving conditions, that is:
The amount of TV channnels operating in the region and the TV channels
number, on which the signals are transmitted.
The signal levels received from the transmitter – they will predetermine
possible usage of directional antenna with high gain or suitable preamplifier
assembly
The transmitters located in the region – if the signals are received from different
directions there is need of assembling the individual antenna (antennas) for
each direction.
2. Connect antennas to the amplifier inputs:
• TV bands IV and V antennas (470...862 MHz) – to UHF1, UHF2 inputs,
• TV bands III antennas (174…230 MHz) – to VHF input,
• FM antenna (47...108 MHz) – to BI/FM input.
Caution:
It is recommended to connect to this input the antenna receiving the most of TV
channels.
It is possible to connect to UHF1, UHF2, and UHF3 inputs antennas with
preamplifiers. Preamplifiers will be detected automatically and the 12V DC
voltage will be provided on proper input.
UHF3 input is universal input. This input allows to connect:
- TV band IV and V antenna, or
- TV band III, IV and V antenna (VHF input will be disconnected, UHF3 input
becomes wideband input VHF+UHF – see Table 1), or
- additional devices (video camera with A/V modulator, satellite receiver, etc.)
Possible combination of TV bands and VHF and UHF3 inputs depends on S3
switch position shown in Table 1.
Table 1
TV bands connected to inputs
S4 switch position
VHF input UHF3 input
← VHF UHF
→ — VHF + UHF
←, → - S4 switch in left or right position
2713-2902-108 3
ver. 1.0
3. Using S1, S2 and S3 switches, assign the required number of channel paths
P1…P6 to both of the UHF inputs. Possible combination of inputs and channel
paths are shown in Table 2.
Table 2
Channel paths connected to the UHF
S1, S2 and S3 switches positions
inputs
S1 S2 S3 UHF1 input UHF2 input
↑ ↑ ↑ P1...P3 P6
↑ ↑ ↓ P1...P3 P5...P6
↑ ↓ ↑ P1...P3 P6
↑ ↓ ↓ P1...P3 P4...P6
↓ ↑ ↑ P1...P4 P6
↓ ↑ ↓ P1...P4 P5...P6
↓ ↓ ↑ P1...P5 P6
↓ ↓ ↓ P1...P6 —
↑, ↓ - S1, S2 or S3 switches in up and down positions
4 2713-2902-108
ver. 1.0
2. Choose the TV channel to which channel path P1 will be assigned.
3. Tune using the regulator „21...69” selected channel path to get the best picture on
TV. At closing to point of proper filter alignment, the picture quality should be
better. Remember, that in case of high signal level, it is hard to observe picture
quality improvement, because of signal excess will be aligned by auto gain
regulation system in TV receiver. In such case, reduce signal level by gain
regulator „ ” of chosen channel. At lowered level, filter tuning enables to
observe the picture quality changes. Then the maximum output signal level will be
corresponding to the best picture quality.
Caution: It is not recommended to set the gain regulators „ ” in the right end
position.
4. Repeat steps from point 2 and 3 until all UHF channels are assigned to channel
paths.
2713-2902-108 5
ver. 1.0
III. VHF output signals settings
Using the gain regulator „ ” of UHF range, set the required output signal level.
IV. FM path
The BI/FM path is not adjustable.
SAFETY:
1. To achieve proper ventilation, no objects should be placed at the distance smaller
than 5 cm from the device.
2. The device should not be covered by any objects like papers, tablecloths,
hangings, etc.
3. Placing of open fire sources, like burning candles, nearby the device is not
recommended.
4. The device should be operated in a temperate climate.
5. The device should not be exposed to drops and splashing water.
6. No objects filled with water should be placed on the device.
6 2713-2902-108
ver. 1.0
TECHNICAL DATA
INPUTS
WWK–861
BI/FM VHF UHF1, UHF2 UHF3
470÷862 MHz
Frequency range 47÷108 MHz 174÷230 MHz 6 tuned channel 470÷862 MHz
paths*
Gain 24 ±2 dB 35 ±2 dB 43 ±3 dB 30 ±2 dB
-20 dB -20 dB 0, -3, -6 dB
Gain regulation —
smooth smooth switchable
Selectivity of UHF channel
— — ≥ 22 dB —
paths (± 20MHz)
Noise figure 3 dB 3 dB 5 dB —
Max. input level** 79 dBµV 85 dBµV 81 dBµV 88 dBµV
Min. input level***
- for S/N>30dB 35 dBµV 35 dBµV 37 dBµV —
- for S/N>45dB 50 dBµV 50 dBµV 52 dBµV —
Isolation between inputs:
- UHF - UHF ≥ 25 dB
- BI/FM/VHF - UHF ≥ 50 dB
- BI/FM – VHF ≥ 30 dB
Max. output signal level:
- for 2 TV signals 103 dBµV 108 dBµV 112 dBµV 112 dBµV
- for 6 TV signals — — 107 dBµV 107 dBµV
(DIN 45004B (-60dB))
Preamplifiers supply /
— — 12 V DC/50 mA 12 V DC/50 mA
max. current
In. / out. Impedance 75 Ω / 75 Ω
Temperature Operating
- 10...+ 50°C (263...323K)
range
Power supply / Power
230 V AC, 50 Hz / 8 W
consumption
Dimensions / Weight 225 x 130 x 50 mm / 0,75 kg
*) allowed channel path connection combinations with antenna inputs are shown in the Table 2
**) for higher input levels from the antenna an external input attenuator should be used
***) for lower input levels the use of an antenna preamplifier is recommended
2713-2902-108 7
ver. 1.0
EXEMPLARY APPLICATIONS of WWK-861:
Direction 1 Direction 2
UHF band Antenna UHF band Antenna VHF band Antenna
ATV 16/21-60
FM Antenna
ADFM - 2
WWK-861
21 21 21 21 21
69 69 69 69 69
6
3
0
dB
8 2713-2902-108
ver. 1.0