Professional Documents
Culture Documents
1. Contents:
1. CONTENTS: -1-
2. INTRODUCTION -2-
7. FAQ - 11 -
9. OUR TEAM - 12 -
10. SUPPORT - 13 -
10.1. ADDRESSES: - 13 -
10.2. OUR FORUM - 13 -
10.3. HOW TO GET HELP? - 13 -
10.3.1. HOW TO SPEED UP GETTING HELP? - 13 -
10.3.2. HOW TO ASK QUESTIONS - 14 -
10.3.3. HOW TO SEARCH ON FORUMS - 14 -
10.4. You need something more? - 15 -
2. Introduction
Universal Samsung Tool Pro by Vahid Shahabi is an application for flashing, unlocking,
repairing, tuning and making all other thing with Samsung phones. Today, UST Pro is the most powerful
tool in its class.
We are working every day to provide you good support and solve your problems with Samsung
phones. We know, how hard is to keep on top of the wave of GSM service. So, you may be sure you will
get supreme support from us. Please contact us at any time. We will do our best to help you solve your
problems!
3
3.1.2. At first:
- Download the driver according to the OS you are running and save it anywhere to your hard
disk
- Do not plug dongle in! If you did so, unplug the dongle and reboot
After successful dongle drivers installation you should have three devices listed in My Computer
Properties->Devices like shown on screenshot (it is taken from Windows XP, but all the devices are the
same on both OSes.
WARNING! You have NT Administrator rights to install dongle drivers on Windows 2000
or XP!
4
- Run Driver2kXP.exe you just downloaded or run it from CD came with UST.
- Press Next buttons in installer.
- At the end of the installation press Finish in the installer window. Windows will find some
hardware. It will ask you for some files location. Point it to c:\program files\UST Pro\Dongle
Drivers for Win2k-XP if you changed default path of UST Pro drivers installation, then use path
you entered
- After Windows will finish all new devices installation you may plug dongle in. Windows will
find some more devices and ask for path again. Point it to the same path again.
- If all ok - you may now run UST (see below UST Activation)
After successful dongle drivers installation you should have three devices listed in My Computer
Properties->Devices like shown on the screenshot (it is taken from Windows XP, but all the devices are
the same on both OSes.
If you are qualified enough, you might want to install UST Dongle Drivers manually. For this
operation refer to page http://www.reflexreaders.com/Support/Downloads/downloads.html Remember,
that for installing drivers on Win9x you need to install Smart Cards Base Components from
SCBASE.exe and SMCLIB.exe. These files are not necessary on Win2000/XP platforms.
You may post your question in Dongle (Smartcard) subforum of http://www.vsh-gsm.com/forum.
But please, provide us as much information as you can on problem you encounter to help us help you.
Trouble: When I run UST Pro it shows "Loading" window and stops at 8%!
Reason: Dongle drivers are not correctly installed.
5
How to solve: Reinstall Dongle drivers completely. Look above for instructions on how to
reinstall dongle drivers.
Trouble: When I run UST Pro it shows "Loading" window and it will exit in 16%!
Reason: Dongle is not connected or need to be restarted.
How to solve: Connect dongle to USB port, or if it is already connected just remove it from pc
and insert it again.
Trouble: When I run UST Pro it shows "Loading" window and it will exit or hang in 80%! I have
UST 1.0.5 or 1.0.6
Reason: Activation file for your dongle is absent.
How to solve: Send "req.bin" file from UST Pro installation folder your UST Pro dealer, we will
send you dongle activation file in few hours!
Trouble: When I run UST Pro it shows "Loading" window and says: "Bad activation status...!
Reason: Activation file for your dongle is absent.
How to solve: Send "req.bin" file from UST Pro installation folder your UST Pro dealer, he will
send you dongle activation file in some time!
6.2. Unlocking
6.2.2. Procedure for: C100, T2/30x, M1xx, A1/3/40x (Repair "Wrong Card" &
unlock)
Power OFF phone and connect it to cable.
Note: After connecting cable to A30x/A40x phone must go to TEST mode (the service light will
power on in RED/ORANGE), PHONE MUST NOT GO TO CHARGE MODE if so you have
bad or wrong cable.
Run UST and select phone model then select Unlock" and press Make job button.
Wait for UST to unlock your phone (maximum some seconds) and give you such message:
"Operation completed successfully"
Optional: Disconnect phone from PC, power ON phone without SIM card and enter
*2767*2878# to phone.
6.3.1. Procedure for: A20x, A800, Nxxx, Rxxx, Txxx, Vxxx, Sxxx, Qxxx, Pxxx
Power ON phone (Qxxx must be OFF!!!) without SIM card and connect it to cable.
9
Run UST, select phone model, enter desired IMEI then select "Write IMEI" and press Make job
button.
Wait for UST to program new IMEI to your phone and give you such message: "Operation
completed successfully
Note: If you get this message "No response from phone!" just disconnect phone, replace battery
and do the procedure from begin.
Note: If your phone not repaired after these procedures so its not SW problem, just open phone and clean
the pcb perfectly, if not repaired so, try to change EEPROM IC.
To work with this function phone have to be in the state like when writing EEPROM. If it is
specified, that the phone must be off, when writing EEPROM, then power it off before performing
actions, specified below.
7. FAQ
Q: I have heard, that UST is cracked. Is it true?
A: There were some hack attempts on UST (not UST Pro!) in the past. As we know, there were
no successful crack attempts. All cracked UST versions are half-cracked. Sometimes they kill phones,
especially new models. But, nevertheless, for our customers convenience we released UST Pro with
extremely strong protection based on smartcard. This protection is almost impossible to be cracked.
Q: My V2xx shows message Remove IRDA or data cable when trying to use
camera. Can this be corrected by UST?
A: The problem is hardware damage by some reason (wrong unlock or unlock with
cracked UST). Currently it cant be solved by any software. Only by replacing certain IC.
Please refer here to read more on this topic: http://www.vsh-gsm.com/forum/viewtopic.php?
t=112. You need to register on the forum first! To do this just press Register button on the top of
main forum page.
Q: I have UST, not UST Pro and I need some flash files, which I cant find in UST
support area. Where can I get them and when will they be released.
A: Unfortunately, because of some unsuccessful UST hack attempts, there are many half-
cracked UST versions on the internet which are sold by the cheaters. These version suddenly kill
phones, so to prevent cheaters from making money on selling not-working half-cracked UST, we
decided to change UST protection scheme to smartcard. And we stopped support of earlier
versions of UST. Now all updates will be released only for UST Pro. We hope you will
understand us and excuse any inconvenience You may upgrade your UST to UST Pro only for
50$! For this you should contact your dealer, that sold you UST.
Q: I have A3xx/A4xx and my flasher shows Flash sector locked, UST Pro hangs
on Uploading bootloader, or the phone powers on, shows something about Caller and
powers off.
A: You should unlock Flash sector of your phone with UST Pro 2.3 or higher and after
this operation phone will accept any A3xx/A4xx flash in a normal way. Dont forget after
flashing make custom E2P reset by pressing *2767*2878# without SIM card. This will prevent
phone freezing with SIM card.
Q: I cant run UST Pro! When I click UST Pro icon it doesnt sho any info at all!
A: Seem, that you have some Antivirus AutoProtection On. Antivirus is now in memory
and checking files, you open or run. UST protection recognizes this like hack attempt and
doesnt start. Please turn your Antivirus AutoProtection Off or unload it from memory.
9. Our team
Programmers Team:
Main Programmer, UST creator and project leader: Vahid Shahabi
Special thx & greets to: SiroYa, Romain, YiL, Guro
10. Support
10.1. Addresses:
Website www.GsmHacking.com UST & UST Pro support area
13
Forum: http://www.vsh-gsm.com/forum - UST support forum
E-Mail : sales@gsmhacking.com
Please note, that every time you enter our support area, your IP is logged. If we will find
out that your login and password is used by another person we will immediately stop your
support! Do not share your login and password with anybody! Do not post them anywhere!
Some examples (they are not took from life, only a fairy tale :)
UST shows error xxxxxx while flashing
[Solved] Samsung xxxx shows Limited Service after flashing with xx.xx and
FactoryReset made.
[HowTo] Safe flashing xxxx and yyyy
[Wanted] T200 flash with Simplified Chinese language
Best regards,
UST support team
P.S. All questions and suggestions about the contents and the quality of this manual
please send to FractalizeR@newmail.ru
Best regards,
FractalizeR