Professional Documents
Culture Documents
Supplementary
Installation and
Operating Instructions
HART Communicator 275
Field Communicator 375
Asset Management Solutions (AMS)
Process Device Manager (PDM)
UFC 030
Ultrasonic Flow Converter
1 General Information 3
3.2 Operating 6
4.2 Operating 6
5.2 Operating 7
1 General Information
The UFC 030 is a four-wire transmitter with 4...20mA current output and HART capability. Dependent on device
implementation it is available with active/passive current output (standard) or passive current output (MODIS).
Electrical connection: Refer to section Electrical connection of the signal inputs and outputs of the following manual:
Installation and Operating Instructions Universal 3-Beam ultrasonic flowmeter UFM 3030 Compact
ultrasonic flowmeter UFC 030 Ultrasonic flow converter UFS 3000 Ultrasonic flow sensor (KROHNE)
a) As a point-to-point connection between the UFC 030 and the HART master equipment. The instrument's current
output may be active or passive.
Primary Master
HART Analog
Modem
4
mA
20 Terminal I/C
HART
Terminal
Power 250
4...20 mA
Supply
b) As a multipoint connection (multidrop) with up to 15 devices (UFC 030 or other HART equipment) in parallel. The
instrument's current outputs must be passive.
Multidrop Mode
Primary Master
HART
Modem
HART
Power 250
Supply
Terminal I/C
4 mA 4 mA Terminal
...
Secondary Master Up to 15
Slaves
...
UFC 030 UFC 030
Addr. > 0 Addr. > 0
(passive Current Output) (passive Current Output)
In case the UFC 030's current output shall work continuously active a 'third wire' is needed to properly connect it
together with two-wire loop powered devices in the same network.
Primary Master
HART
4 mA 4 mA
HART two-wire
Modem loop powered
devices
...
Addr. > 0 Addr. > 0
Power HART
Supply Terminal V+
4 mA 4 mA Terminal I/C
four-wire
active
source
250 devices
Secondary Master
UFC 030
...
UFC 030
Addr. > 0 Addr. > 0
For information about Transmitter Revisions and related Device Descriptions refer to the KROHNE HART Device
List.
3.2 Operating
Refer to the UFC 030 Menu Tree HC275 / FC375 (Attachment A).
The UFC 030 operation via HC275 / FC375 is made quite close to the manual instrument control via keypad.
Due to limitations of the HC275 / FC375 there are some peculiarities:
The online help of each parameter is only a short form help. However it contains the function number as a
reference to the devices local display and the Installation and Operating Instructions for a comprehensive
description.
Some selection lists (e.g. for output functions) may contain items which are actually not valid for the device
concerned. However invalid settings are rejected when trying to send them to the device.
Parameter protection via passwords (Entry Code, Service Code) is the same as on local display. Please refer to the
online help for valid symbols according to devices keypad.
The set of parameters of the HC275 standard configuration is only a partial set which doesnt contain service
parameters. However the HC275 full configuration contains a complete set of parameters. Prior to sending a full
configuration to a device the Service Code protection must be disabled in case. Both types of configurations can be
transferred to AMS.
The FC375 always creates a full configuration for interaction with AMS. Still the FC375 considers only a partial
parameter set (like the HC275 standard configuration) when sending it to a device.
4.2 Operating
Refer to the UFC 030 Menu Tree AMS (Attachment B).
Due to AMS requirements and conventions the UFC 030 operation differs to some extent from operation with HC275
/ FC375 and via local keypad.
Due to limitations of the HC275 / FC375 which affect also AMS there are some peculiarities:
The online help of each parameter is only a short form help. However it contains the function number as a
reference to the devices local display and the Installation and Operating Instructions for a comprehensive
description.
Some selection lists (e.g. for output functions) may contain items which are actually not valid for the device
concerned. However invalid settings are rejected when trying to send them to the device.
Parameter protection via passwords (Entry Code, Service Code) is the same as on local display. Please refer to the
online help for valid symbols according to devices keypad.
5.1 Installation
If the UFC 030 Device Description is not already installed on the PDM System a so called Device Install is needed
(available as download from KROHNE Download Centre on the internet or on floppy disk / CD-ROM from
KROHNE).
For installing the DD with the Device Install refer to the PDM Manual section 11.2:Device Install / Integrating
Devices in SIMATIC PDM with 'Device Install'". Please read also the readme.txt, which is also contained in the
Device Install.
5.2 Operating
Refer to the UFC 030 Menu Tree PDM (Attachment C).
Due to PDM requirements and conventions the UFC 030 operation differs to some extent from operation with HC275
/ FC375 and via local keypad.
Due to limitations of the HC275 / FC375 which affect also PDM there are some peculiarities:
The online help of each parameter is only a short form help. However it contains the function number as a
reference to the devices local display and the Installation and Operating Instructions for a comprehensive
description.
Some selection lists (e.g. for output functions) may contain items which are actually not valid for the device
concerned. However invalid settings are rejected when trying to send them to the device.
Parameter protection via passwords (Entry Code, Service Code) is the same as on local display. Please refer to the
online help for valid symbols according to devices keypad.
1 Function I
2 Value I
2 View In/Outputs 3 %Range I
4 Function P Opt
5 Value P Opt
6 %Range P Opt
7 Analog Input 1 Opt
8 Analog Input 2 Opt
1 Simulation Mode
5 Simulation 2 Uncorrected Flow
3 VOS
4 Gain
2 Installation 5 Analog Input 1 Opt
2, 3
6 Analog Input 2 Opt
3 Quit/Reset 3 Service Menu 5 7 Digital Input Opt
4 HART Variables 4
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
1 Display Flow
3 Display 2 Function Totalizer
3 Display Totalizer
4 Volume Units Opt
5 Energy Units Opt
6 VOS Units
7 Cyclic Display
8 Error Messages 1 Format Flow Loc
9 Date 2 Format
10 Analog Input Opt Heat Flow Loc, Opt
11 Signal Gain 3 Format Volume Loc
12 Display Formats 4 Format
Energy Loc, Opt
4 Current Output I
5 Pulse Output P
6 Digital Input C 3
3 Service Menu 5
7 User Data
3 Quit/Reset 4 8 Logging
4 HART Variables
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
1 Dynamic 1
Variables 1 Flow
1 Test / Info 1 1 1 Function I
2 Version
2 Direction I
3 Display
2 Configuration / 3 Range I
2 Installation 4 I 0%
Test 4 Current Output I
5 I 100%
6 Limit
1 Function P Opt
2 Direction P Opt
3 Digital Output Opt
5 Pulse Output P 4 Trip.Point 1 Opt
5 Trip.Point 2 Opt
6 Time Constant Opt
7 Output Opt
8 Pulserate Units Opt
9 Pulsrate Opt
10 Units
Pulse/Unit Opt
11 Pulse/Unit Opt
12 Pulswidth Opt
3 Service Menu 5
3 Quit/Reset 4
4 HART Variables
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
1 Dynamic 1
Variables
1 Test / Info 1
2 Installation 2, 3
2 Configuration /
Test 3 Service Menu 5
1 Quit Errors
3 Quit/Reset
2 Reset Totalizers Opt
3 Master Reset
4 Reset Conf. Flag
1 PV is Rd
3 Dyn. Vars Settings 2 SV is
3 TV is
4 4V is
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
1 Calibration 4 mA
3 Current Output I 2 Calibration 20 mA
Opt
3 Calibrate Current
Output I
1 Dead Time
2 Trigger Select
3 Trigger Level 1
4 Sensor Opt
4 Trigger Margin
5 Sensor Frequency
6 Zero Value Path 1
....
1 Calibrate Analog
Input 1
6 An. Inp. Calib. Opt
2 Calibrate Analog
Input 2
3 Input 1 0mA
4 Input 1 20mA
5 Input 2 0mA
6 Input 2 20mA 1 SI units
2 Pulse Output
1 Manufacturer 3 Current Output
7 Device 2 Model No. 4 Digital Input
Information Opt 3 Serial Number Rd 5 Analog IO module
4 P2 HW No. 6 HART Interface Rd
5 Front end HW No. 7 FF Interface Rd
6 DSP HW No. 8 PA Interface Rd
7 Available I/O 9 MODIS Version Rd
Paramter Protection
Process Input Current Output Pulse Output
-----------------------------------
Rename Flow Units Current Output Function P Opt
Full Scale Function I Direction P Opt
Unassign Master TC Direction I Digital Output Opt
Assign / Replace Range I Trip. Point 1 Opt
L.F. Cutoff I 0% Trip. Point 2 Opt
----------------------------------- L.F. Cutoff I 100% Time Constant Opt
Audit Trail Cutoff on Opt Limit Output Opt
Cutoff off Opt Calibration 4mA Opt Pulserate Units Opt
Record Manual Event Calibration 20mA Opt Pulserate Opt
Drawings / Notes ... VOS Min/Max Units Units Pulse/Unit Opt
Min VOS Pulse/Unit Opt
Help ... Max VOS Pulsewidth Opt
Display
Local Display Display Formats
Display Flow Language Format Flow Loc
Function Totalizer Cyclic Display Format Heat Flow Opt, Loc
Display Totalizer Error Messages Format Volume Loc
Designations: Volume Units Opt Date Format Energy Opt, Loc
Opt Optional, dependent on device Energy Units Opt Text Volume
implementation / configuration VOS Units Text Time
Rd Read-only Analog Input Opt Unit Volume
Loc Local AMS, affects only AMS views Signal Gain Unit Time
Device
Configure
Device Info Version Available I/O Opt
Compare Manufacturer Rd Enable Reset SI Units Opt
Clear Offline Model Number Rd Pulse Output Opt
Serial Number Rd Current Output Opt
----------------------------------- P1 HW No. Rd Digital Input Opt
Status/Conditions P2 SW No. Rd Analog IO module Opt
3 FE HW No. Rd HART Interface Opt, Rd
Process Variables DSP HW No. Rd FF Interface Opt, Rd
Scan Device DSP SW No. Rd PA Interface Opt, Rd
MODIS Version Opt, Rd
-----------------------------------
Calibration Management
HART
Diagnostics and Test
Calibrate Revision Numbers Identification
Universal rev Rd Manufacturer Rd Final asmbly num
Reset Fld dev rev Rd Model Rd Snsr s/n
Paramter Protection Software rev Rd Dev ID Rd
Hardware rev Rd Poll Addr Dynamic Variables Settings
----------------------------------- Tag PV is Rd
Rename Preambles Date SV is
Num req preams Rd Dev des TV is
Unassign Num resp preams Rd Message 4V is
Assign / Replace Write Protect Rd
-----------------------------------
Audit Trail
Test Current Output I
Record Manual Event
Test Pulse Output P Opt
Drawings / Notes ... Test Analog Inputs Opt Zero Calibration Opt
Calibrate Current O. I Opt
Help ...
Calibrate Analog Inp. 1 Opt
Quit Errors Calibrate Analog Inp. 2 Opt
Reset Totalizers Opt Calibrate Path Opt
Master Reset
Reset Conf. Changed Flag
Reset Menu Parameters Opt
Reset Service Param. Opt
Reset Calibration Par. Opt
Designations: Reset All Parameters Opt
Opt Optional, dependent on device Reset Factory Par. Opt
implementation / configuration
Rd Read-only Entry Code 1
Loc Local AMS, affects only AMS views Service Code
1 Configure
Compare
IO / Totalizers Raw Values
Clear Offline
----------------------------------- Underrun analog input 1 Totalizer Overrun Error Relative
Overrun analog input 1 Totalizer Storage Error Flow Speed 1 ... 3 Opt
Status/Conditions Underrun analog input 2 PRimary flow Overrun
Process Variables Overrun analog input 2 Error SOS 1 ... 3 Opt
20mA Analog Input HW SECondary flow Overrun
Scan Device Error Error Gain 1 ... 3 Opt
----------------------------------- Calibration Data Lost
Current Output Overrange
Calibration Management Current Output in fixed
Diagnostics and Test mode
Pulse Output Overrange
2 Calibrate Pulse Output in fixed
Reset mode
Paramter Protection
-----------------------------------
Rename
Process Values Totalizers Current Output
Unassign
Actual Flow Totalizer 1 Opt Value
Assign / Replace Corrected Flow Opt Totalizer 2 Opt Percent of Range
VOS Totalizer Sum Opt
-----------------------------------
Audit Trail Correction
Analog Input 1 Opt
Record Manual Event
Analog Input 2 Opt Pulse Output P
Drawings / Notes ... Value Opt
Additional Values Percent of Range Opt
Help ...
F/R Indication
Gain
Device HART
Tag Polling Address
Descriptor Opt Device ID
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
Test
Test Inputs Opt Outputs
Analog Input 1 Test Current Output I
Analog Input 2 Test Pulse Output P Opt
-----------------------------------
Reset
Reset Reset Device Parameters Opt
<Quit Errors> <Reset Menu Par.>
Reset
<Reset Totalizers> Opt <Reset Service Par.>
<Master Reset> <Reset Calibration Par.>
<Reset Conf. Changed Fl.> <Reset All Par.>
<Reset Factory Par.>
-----------------------------------
Calibration
Zero Calibration Analog Input Calibr. Opt Measuring Path Calibr. Opt
Zero Value 1 ... 3 Opt, Rd Input 1 0mA Opt <Calibrate Path> Opt
<Zero Calibration> Opt Input 1 20mA Opt
Calibration Input 2 0mA Opt
Current Output Calibr. Opt Input 2 20mA Opt
Calibration 4 mA Opt <Calibr. An. Inp. 1> Opt
Calibration 20 mA Opt <Calibr. An. Inp. 2> Opt
<Calibrate Current O.> Opt
-----------------------------------
Parameter Protection
Parameter Protection Entry Code Lock Rd
<Activcte/Deactivate Entry Code Lock>
----------------------------------- Service Code Lock Rd
<Deactivate Service Code Lock>
HART Communication
HART Communication
Preambles Dynamic Variables Settings
Request Preambles Rd PV is Rd
Response Preambles SV is
TV is
4V is
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
Device Status
Yt Diagram Y t Diagram
Actual Flow
Corrected Flow Opt
VOS
Device Status 3
-----------------------------------
Toolbar
Status Bar
-----------------------------------
Update
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
Display Device
Device Info HART IDs
Yt Diagram 2 Manufacturer Rd Tag
Model Number Rd Manufacturer Rd
Outputs/Inputs Serial Number Rd Device Type Rd
P1 HW No. Rd HART Device ID Rd
P2 SW No. Rd Universal Revision Rd
FE HW No. Rd Device Revision Rd
DSP HW No. Rd Software Revision Rd
DSP SW No. Rd Hardware Revision Rd
Date Rd
Final Assembly No. Rd
Sensor Serial No. Rd
Status
I/O Totalizers
Calibration Data Lost Totalizer Overrun Error
20mA Analog Input HW Totalizer Storage Error
Error PRimary flow Overrun
Underrun analog input 1 Error
Overrun analog input 1 SECondary flow Overrun
Underrun analog input 2 Error
Overrun analog input 2
Current Output Overrange
Pulse Output Overrange
Current Output in fixed
mode
Pulse Output in fixed
mode
-----------------------------------
Toolbar
Status Bar
-----------------------------------
Update
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only
Identification Output
IO Fitted Rd
Operation Unit
Device Current Output I
4 Function I
----------------------------------- Direction I
Input Range I
I 0%
Measuring Limits I 100%
Operation Parameter Limit
Calibration 4mA Opt
Sensor Calibration 20mA Opt
Version
Pulse Output P Opt
Analog Input Opt 4 Function P
Measuring Path Opt Direction P
Digital Output Opt
Plausibility Filter Trip. Point 1 Opt
----------------------------------- Trip. Point 2 Opt
Time Constant
Output Output Opt
Current Output I Pulsrate Units Opt
Pulserate Opt
Pulse Output P Opt Units Pulse/Unit Opt
----------------------------------- Pulse/Unit Opt
Pulsewidth Opt
Human Interface
Local Display
Human Interface
Display Formats Display Flow
Function Totalizer
Display Totalizer Opt
Volume Units Opt
Energy Units Opt
VOS Units
Analog Input Opt
Signal Gain
Local Display
Language
Cyclic Display
Error Messages
Date Opt
Text Volume
Text Time
Unit Volume
Unit Time
Display Formats
Format Flow Loc
Format Heat Flow Opt, Loc
Format Volume Loc
Format Energy Opt, Loc
Designations:
Opt Optional, dependent on device
implementation / configuration
Rd Read-only