You are on page 1of 52

ENGLISH

FRANAIS
DEUTSCH

KD-X230 / KD-X130
DIGITAL MEDIA RECEIVER
INSTRUCTION MANUAL
RCEPTEUR MULTIMDIA NUMRIQUE
MANUEL DINSTRUCTIONS
DIGITAL-MEDIA-RECEIVER
BEDIENUNGSANLEITUNG

B5A-0821-00 [E]

JS_JVC_KD_X230_X130_E_C00.indd 1 Data Size: B6L (182 mm x 128 mm) 14/8/2015 11:59:36 AM


Book Size: B6L (182 mm x 128 mm)
Entsorgung von gebrauchten elektrischen und elektronischen Gerten und Batterien
(anzuwenden in Lndern mit einem separaten Sammelsystem fr solche Gerte)
Das Symbol (durchgestrichene Mlltonne) auf dem Produkt oder seiner Verpackung weist
darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall behandelt werden darf,
sondern an einer Annahmestelle fr das Recycling von elektrischen und elektronischen Gerten
und batterien abgegeben werden muss.
Durch Ihren Beitrag zur korrekten Entsorgung dieses Produktes schtzen Sie die Umwelt und
Information on Disposal of Old Electrical and Electronic Equipment and Batteries die Gesundheit Ihrer Mitmenschen.
(applicable for countries that have adopted separate waste collection systems) Unsachgemsse oder falsche Entsorgung gefhrden Umwelt und Gesundheit. Weitere
Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as Informationen ber das Recycling dieses Produktes erhalten Sie von Ihrer Gemeinde oder den
household waste. kommunalen Entsorgungsbetrieben.
Old electrical and electronic equipment and batteries should be recycled at a facility capable of Achtung: Das Zeichen Pb unter dem Symbol fur Batterien zeigt an, dass diese Batterie Blei
handling these items and their waste byproducts. enthalt.
Contact your local authority for details in locating a recycle facility nearest to you. Proper
recycling and waste disposal will help conserve resources whilst preventing detrimental effects
on our health and the environment.
Notice: The sign Pb below the symbol for batteries indicates that this battery contains lead.

Information sur llimination des anciens quipements lectriques et lectroniques


et piles lectriques (applicable dans les pays qui ont adopt des systmes de collecte
slective)
Les produits et piles lectriques sur lesquels le pictogramme (poubelle barre) est appos ne
peuvent pas tre limins comme ordures mnagres.
Les anciens quipements lectriques et lectroniques et piles lectriques doivent tre recycls
sur des sites capables de traiter ces produits et leurs dchets.
Contactez vos autorits locales pour connatre le site de recyclage le plus proche. Un recyclage
adapt et llimination des dchets aideront conserver les ressources et nous prserver des
leurs effets nocifs sur notre sant et sur lenvironnement.
Remarque: Le symbole Pb ci-dessous sur des piles lectrique indique que cette pile contient
du plomb.

JS_JVC_KD_X230_X130_E_C00.indd i Data Size: B6L (182 mm x 128 mm) 14/8/2015 11:59:37 AM


Book Size: B6L (182 mm x 128 mm)
For Israel

Declaration of Conformity with regard to the EMC Directive


Declaration of Conformity with regard to the RoHS Directive 2011/65/EU
Manufacturer:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
EU Representative:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany

Dclaration de conformit se rapportant la directive EMC


Dclaration de conformit se rapportant la directive RoHS 2011/65/EU
Fabricant:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
Reprsentants dans lUE:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany

Konformittserklrung in Bezug auf die EMC-Vorschrift


Konformittserklrung in Bezug auf die RoHS-Vorschrift 2011/65/EU
Hersteller:
JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan
EU-Vertreter:
JVC Technical Services Europe GmbH
Konrad-Adenauer-Allee 1-11, D-61118 Bad Vilbel, Germany

ii

JS_JVC_KD_X230_X130_E_C00.indd ii Data Size: B6L (182 mm x 128 mm) 14/8/2015 11:59:37 AM


Book Size: B6L (182 mm x 128 mm)
CONTENTS BEFORE USE
BEFORE USE 2 IMPORTANT
BASICS 3 To ensure proper use, please read through this manual before using this product. It is especially important
that you read and observe Warning and Caution in this manual.
GETTING STARTED 4 Please keep the manual in a safe and accessible place for future reference.
1 Cancel the demonstration Warning
2 Set the clock Do not operate any function that takes your attention away from safe driving.
3 Set the basic settings
Caution
RADIO 5 Volume setting:
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
AUX 6
Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
USB / iPod / ANDROID 7 the output level.
General:
AUDIO SETTINGS 9 Avoid using the external device if it might hinder safe driving.
DISPLAY SETTINGS 11 Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
REFERENCES 11 Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short
Maintenance circuit.
More information
TROUBLESHOOTING 13
INSTALLATION /
CONNECTION 14
SPECIFICATIONS 16

How to read this manual


Operations are explained mainly using buttons on the faceplate of KD-X230.
English indications are used for the purpose of explanation. You can select the display language from the
menu. ( 4)
[XX] indicates the selected items.
( XX) indicates references are available on the stated page.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 2 18/8/2015 10:33:12 AM
Book Size: B6L (182 mm x 128 mm)
BASICS
Faceplate Attach

Volume knob Display window

Detach
KD-X130
TI ST

How to reset
Detach button

Your preset adjustments will be


erased except stored radio stations.

To On the faceplate
Turn on the power Press .
Press and hold to turn off the power.
Adjust the volume Turn the volume knob.
Press the volume knob to mute the sound or pause playback.
Press again to cancel.

Select a source Press repeatedly.


Press , then turn the volume knob within 2 seconds.
Change the display information Press repeatedly. ( 12)

ENGLISH 3

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_1a.indd 3 4/9/2015 9:40:21 AM
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
3 Set the basic settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press to exit.
1 Cancel the demonstration To return to the previous setting item, press .
When you turn on the power (or after you reset the unit), the display Default: XX
shows: CANCEL DEMO PRESS VOLUME KNOB SETTINGS
1 Press the volume knob. BEEP ON:Activates the keypress tone.; OFF:Deactivates.
[YES] is selected for the initial setup.
2 Press the volume knob again. SRC SELECT
DEMO OFF appears. AM * ON:Enables AM in source selection.; OFF:Disables.

2 AUX * BTADAPTER:Selects when the KS-BTA100 Bluetooth adapter is connected to


Set the clock the AUX jack. ( 6); ON:Enables AUX in source selection.; OFF:Disables.
1 Press and hold . F/W UPDATE
2 Turn the volume knob to select [CLOCK], then press the knob.
3 Turn the volume knob to select [CLOCKSET], then press the knob. SYSTEM
4 Turn the volume knob to make the settings, then press the knob. F/W xxxx YES:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated).
Day Hour Minute For details on how to update the firmware, see: <http://www.jvc.net/cs/car/>.
5 Turn the volume knob to select [24H/ 12H], then press the knob.
6 Turn the volume knob to select [12 HOUR] or [24 HOUR], then press CLOCK
the knob. CLOCK SYNC AUTO:The clock time is automatically set using the Clock Time (CT) data in FM
7 Press to exit. Radio Data System signal.; OFF:Cancels.
To return to the previous setting item, press . CLOCK DISP ON:The clock time is shown on the display even when the unit is turned off.;
OFF:Cancels.
ENGLISH
Select the display language for menu and music information if applicable.

By default, ENGLISH is selected.
ESPANOL
* Not displayed when the corresponding source is selected.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 4 18/8/2015 10:33:13 AM
Book Size: B6L (182 mm x 128 mm)
RADIO
Other settings
1 Press and hold .
2 Turn the volume knob to select [TUNER], then press the
knob.
3 Turn the volume knob to select an item (see the
following table), then press the knob.
4 Repeat step 3 until the desired item is selected/
ST lights up when receiving an FM stereo broadcast with sufficient signal strength.
activated or follow the instructions stated on the
selected item.
Search for a station 5 Press to exit.
1 Press repeatedly to select FM or AM. To return to the previous setting item, press .
2 Press to search for a station automatically.
(or) Default: XX
Press and hold until M flashes, then press repeatedly to search for a RADIO TIMER Turns on the radio at a specific time regardless of the current
station manually. source.
1 ONCE/ DAILY/ WEEKLY/ OFF:Select how often the
Settings in memory timer will be turned on.
2 FM/ AM:Select the band.
You can store up to 18 stations for FM and 6 stations for AM. 3 01 to 18 (for FM)/ 01 to 06 (for AM):Select the preset
station.
Store a station 4 Set the activation day *1 and time.
While listening to a station.... M lights up when complete.
Press and hold one of the number buttons (1 to 6). Radio Timer will not activate for the following cases.
(or) The unit is turned off.
1 Press and hold the volume knob until PRESETMODE flashes. [OFF] is selected for [AM] in [SRCSELECT] after Radio
2 Turn the volume knob to select a preset number, then press the knob. Timer for AM is selected. ( 4)
The preset number flashes and MEMORY appears.
SSM SSM0106 / SSM0712 / SSM1318: Automatically
presets up to 18 stations for FM. SSM stops flashing
Select a stored station when the first 6 stations are stored. Select SSM0712 /
Press one of the number buttons (1to6). SSM1318 to store the following 12 stations.
(or)
*1 Selectable only when [ONCE] or [WEEKLY] is selected in step 1.
1 Press .
2 Turn the volume knob to select a preset number, then press the knob to
confirm.

ENGLISH 5

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 5 18/8/2015 10:33:14 AM
Book Size: B6L (182 mm x 128 mm)
RADIO AUX
Default: XX
Use a portable audio player
LOCAL SEEK ON:Searches only FM stations with good reception.; OFF:Cancels. 1 Connect a portable audio player (commercially available).
Settings made are applicable only to the selected source/station. Once
you change the source/station, you need to make the settings again. 3.5mm stereo mini plug with L shaped connector
(commercially available)
IF BAND AUTO:Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.); WIDE:Subjects to
interference noises from adjacent FM stations, but sound quality will not be
degraded and the stereo effect will remain.
MONO ON:Improves the FM reception, but the stereo effect will be lost.; Auxiliary input jack Portable audio player
OFF:Cancels.
2 Select [ON] for [AUX] in [SRC SELECT]. ( 4)
NEWS-STBY*2 ON:The unit will temporarily switch to News Programme if available.; 3 Press repeatedly to select AUX.
OFF:Cancels. 4 Turn on the portable audio player and start playback.
REGIONAL*2 ON: Switches to another station only in the specific region using the AF
control.; OFF:Cancels. Use a 3-core plug head stereo mini plug for optimum audio
AF SET*2 ON: Automatically searches for another station broadcasting the same output.
program in the same Radio Data System network with better reception
when the current reception is poor.; OFF: Cancels.
TI SET*2 ON: Allows the unit to temporarily switch to Traffic Information if available Use a Bluetooth device
(TI lights up). ; OFF:Cancels. 1 Connect the Bluetooth adapter, KS-BTA100 (separately purchased).
PTY SEARCH*2 Select a PTY code (see below). Wiring harness of the unit
If there is a station broadcasting a program of the same PTY code as you ( 15)
have selected, that station is tuned in. Blue/white
Blue/white: Remote
PTY code: NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, Black
Black: Ground
VARIED, POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),
CLASSICS, OTHER M (music), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, Brown
Brown: Tel muting
PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M
(music), DOCUMENT Auxiliary input jack
2 Register (pair) the Bluetooth device with KS-BTA100.
*2 Only for FM source. 3 Select [BT ADAPTER] for [AUX] in [SRC SELECT]. ( 4)
4 Press repeatedly to select BT AUDIO.
5 Start using the Bluetooth device.
For details, refer to the instruction manual of KS-BTA100.
6

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 6 18/8/2015 10:33:14 AM
Book Size: B6L (182 mm x 128 mm)
USB / iPod / ANDROID
Selectable source:
Start playback
KD-X230:
The source changes automatically and USB/ USB-IPOD/ ANDROID KD-X130
playback starts. KD-X130:
USB/ ANDROID
USB input terminal
USB KD-X230: To directly select USB/ USB-IPOD/ ANDROID source, press .

To On the faceplate
USB 2.0 cable*1
(commercially available) Reverse / Fast-forward*3 Press and hold .
Select a file Press .
iPod/iPhone
Select a folder*4 Press .
Repeat play*5 Press repeatedly.
(Accessory of the TRACK RPT/ FOLDER RPT/ ALL RPT : MP3/WMA/WAV/FLAC file
iPod/iPhone)*1 ONE RPT/ ALL RPT/ RPT OFF : iPod or ANDROID
Random play*5 Press repeatedly.
FOLDERRND/ ALL RND/ RND OFF : MP3/WMA/WAV/FLAC file
ANDROID*2 SONG RND/ ALL RND/ RND OFF : iPod or ANDROID
*1 Do not leave the cable inside the car when not using.
*2 When connecting an Android device, Press [VIEW] to install JVC MUSIC PLAY APP is shown. Follow the instructions to install
the application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.
Micro USB 2.0 cable*1 ( 11)
(commercially available) *3 For ANDROID: Applicable only when [AUTO MODE] is selected. ( 8)
*4 Only for MP3/WMA/WAV/FLAC files. This does not work for iPod/ ANDROID.
*5 For iPod/ ANDROID: Applicable only when [HEAD MODE]/ [AUTO MODE] is selected. ( 8)

ENGLISH 7

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 7 18/8/2015 10:33:14 AM
Book Size: B6L (182 mm x 128 mm)
USB / iPod / ANDROID

Select control mode Select a file from a folder/list


While in USB-IPOD source, press repeatedly. 1 Press .
HEAD MODE: Control iPod from this unit. 2 Turn the volume knob to select a folder/list, then press the
IPHONE MODE: Control iPod using the iPod itself. However, you can still play/ knob.
pause or file skip from this unit. 3 Turn the volume knob to select a file, then press the knob.
While in ANDROID source, press repeatedly. Quick Search
AUTO MODE: Control Android device from this unit via JVC MUSIC PLAY If you have many files, you can search through them quickly.
application installed in the Android device. Turn the volume knob quickly to browse through the list
AUDIO MODE: Control Android device using the Android device itself via quickly.
other media player applications installed in the Android device. Not applicable for iPod.
However, you can still play/pause or file skip from this unit.
Alphabet search (applicable only for iPod):
Select music drive You can search for a file according to the first character.
Press repeatedly. Press or turn the volume knob quickly to select the
desired character (A to Z/ 0to9/ OTHERS).
Stored songs in the following drive will be played back.
Select OTHERS if the first character is other than Ato Z, 0 to 9.
Selected internal or external memory of a smartphone (Mass Storage Class).
Selected drive of a multiple drives device. To return to the previous setting item, press .
To cancel, press and hold .
For iPod, applicable only when [HEADMODE] is selected.
Change the playback speed of the Audiobook For ANDROID, applicable only when [AUTO MODE] is selected.
While listening to the iPod and [HEADMODE] is selected....
1 Press and hold .
2 Turn the volume knob to select [IPOD], then press the knob.
3 Press the volume knob to select [AUDIOBOOKS].
4 Turn the volume knob to select an item, then press the knob.
0.5SPEED / 1SPEED / 2SPEED: Select the desired playback speed of the
Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
5 Press to exit.
To return to the previous setting item, press .

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 8 18/8/2015 10:33:15 AM
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
Default: XX
EQSETTING
EQPRESET Select a preset equalizer suitable to the music genre. (Select [USER] to use the
settings made in [EASY EQ].)
FLAT(Default) / HARD ROCK/ HIP HOP/ JAZZ/ POP/ R&B/ TALK/ USER/
VOCALBOOST/ BASSBOOST/ CLASSICAL/ DANCE
EASYEQ Adjust your own sound settings. The settings are stored to [USER].
Select a preset equalizer
SUB.W SP *1*2: 00to+06 (Default: 03
Press repeatedly. SUB.W *1*3: 08to+08 00
(or) BASSLVL: 06to+06 00
Press , then turn the volume knob within 5seconds. MIDLVL: 06to+06 00
Preset equalizer: FLAT (default), HARD ROCK, HIP HOP, JAZZ, POP, R&B, TALK, USER, TRELVL: 06to+06 00)
VOCAL BOOST, BASS BOOST, CLASSICAL, DANCE PRO EQ 1 BASS / MIDDLE / TREBLE:Select a sound tone.
2 Adjust the sound elements of the selected sound tone.
Store your own sound settings BASS Frequency: 60/ 80/ 100/ 200HZ (Default: 80HZ
Level: 06 to +06 00
1 Press and hold to enter EASY EQ setting. Q: Q1.0/ Q1.25/ Q1.5/ Q2.0 Q1.0)
2 Turn the volume knob to select an item, then press the knob. MIDDLE Frequency: 0.5/ 1.0/ 1.5/ 2.5KHZ (Default: 1.0KHZ
Refer to [EASYEQ] for setting and the result is stored to [USER]. Level: 06 to +06 00
To return to the previous setting item, press . Q: Q0.75/ Q1.0/ Q1.25 Q1.25)
To exit, press . TREBLE Frequency: 10.0/ 12.5/ 15.0/ 17.5KHZ (Default: 10.0KHZ
Level: 06 to +06 00
Other settings Q: QFIX QFIX)

1 Press and hold . AUDIO


2 Turn the volume knob to select an item (see the following table), BASS BOOST +01+05(+01): Selects your preferred bass boost level.; OFF:Cancels.
then press the knob.
LOUD 01/02:Boosts low or high frequencies to produce a well-balanced sound at
3 Repeat step 2 until the desired item is selected/activated or follow
low volume.; OFF:Cancels.
the instructions stated on the selected item.
4 Press to exit. *1 Displayed only when [SUB.W] is set to [ON]. ( 10)
To return to the previous setting item, press . *2 Displayed only when [SPK/PREOUT] is set to [SUB.W/SUB.W]. ( 10)
*3 Displayed only when [SPK/PREOUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W]. ( 10)

ENGLISH 9

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 9 18/8/2015 10:33:15 AM
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
*4 Displayed only when [SUB.W] is set to [ON].
SUB.W LEVEL *4 SPK-OUT *5 00to+06(+03):Adjusts the output level of the
*5 Displayed only when [SPK/PREOUT] is set to [SUB.W/SUB.W].
subwoofer connected via speaker lead. ( 15)
*6 Displayed only when [SPK/PREOUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W].
PRE-OUT *6 08to+08(00):Adjusts the output level of the *7 This adjustment will not affect the subwoofer output.
subwoofer connected to the lineout terminals (REAR/SW) *8 Does not work if [BTADAPTER] is selected for [AUX] in [SRCSELECT]. ( 4)
through an external amplifier. ( 15)
SUB.W *6 ON/OFF: Turns on or off the subwoofer output. Speaker output settings
SUB.WLPF *4 THROUGH:All signals are sent to the subwoofer. ; LOW55HZ/ Select the output setting for the speakers [SPK/PRE OUT], base on the
MID85HZ/ HIGH120HZ:Audio signals with frequencies lower than speaker connection method.
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
SUB.WPHASE *4 REVERSE(180)/ NORMAL(0):Selects the phase of the subwoofer Connection via lineout terminals
output to be in line with the speaker output for optimum performance. For connections through an external amplifier. ( 15)
(Selectable only if a setting other than [THROUGH] is selected for
[SUB.WLPF].) Setting on Audio signal through lineout terminal
[SPK/PRE OUT] REAR/SW
FADER R06F06(00):Adjusts the front and rear speaker output balance.
BALANCE *7 L06R06(00):Adjusts the left and right speaker output balance. REAR/REAR Rear speakers output
VOL ADJUST 15+06(00):Preset the initial volume level of each source REAR/SUB.W Subwoofer output
(compared to the FM volume level). Before adjustment, select the source SUB.W/SUB.W Subwoofer output
you want to adjust. (VOLADJFIX appears if FM is selected.)
AMP GAIN LOWPOWER:Limits the maximum volume level to 25. (Select if the Connection via speaker leads
maximum power of each speaker is less than 50W to prevent damaging For connections without using an external amplifier. However, with this
the speakers.); HIGHPOWER:The maximum volume level is 35. settings you can also enjoy the subwoofer output. ( 15)
D.T.EXP ON:Creates realistic sound by compensating the high-frequency Setting on Audio signal through rear speaker lead
(Digital Track components and restoring the rise-time of the waveform that are lost in [SPK/PRE OUT]
Expander) audio data compression.; OFF:Cancels. L (left) R (right)

TELMUTING *8 ON:Mutes the sounds while using the cellular phone (not connected REAR/REAR Rear speakers output Rear speakers output
through KS-BTA100).; OFF:Cancels. REAR/SUB.W Rear speakers output Rear speakers output
SPK/PREOUT Depending on the speaker connection method, select the appropriate SUB.W/SUB.W Subwoofer output (Mute)
setting to get the desired output. ( Speaker output settings)
If [SUB.W/SUB.W] is selected:
[HIGH120HZ] is selected in [SUB.WLPF] and [THROUGH] is not available.
[R01] is selected in [FADER] and selectable range is [R06]to [00].

10

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 10 18/8/2015 10:33:15 AM
Book Size: B6L (182 mm x 128 mm)
DISPLAY SETTINGS REFERENCES
Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector


Detach the faceplate and clean the connector
1 Press and hold . gently with a cotton swab, being careful not to
2 Turn the volume knob to select an item (see the following table), damage the connector.
then press the knob. Connector (on the reverse
3 Repeat step 2 until the desired item is selected/activated or follow side of the faceplate)
More information
the instructions stated on the selected item. Visit also the following website <http://www.jvc.net/cs/car/> for:
4 Press to exit. Latest firmware updates and latest compatible item list
To return to the previous setting item, press . Android application JVC MUSIC PLAY
Default: XX Any other latest information
DISPLAY Playable files
DIMMER Dim the display and buttons illumination. Playable audio file: MP3 (.mp3), WMA (.wma), WAV(.wav), FLAC (.flac)
OFF:Dimmer is turned off. Playable USB device file system: FAT12, FAT16, FAT32
ON:Dimmer is turned on. Brightness changes to [NIGHT] setting. Even when audio files comply with the standards listed above, playback may be impossible
( [BRIGHTNESS]) depending on the types or conditions of media or device.
DIMMER TIME:Set the dimmer on and off time.
1 Turn the volume knob to adjust the [ON] time, then press the knob. About USB devices
2 Turn the volume knob to adjust the [OFF] time, then press the knob. This unit can play MP3/WMA/WAV/FLAC files stored on a USB mass storage class device.
(Default: [ON]: 18:00 or 6:00 PM
You cannot connect a USB device via a USB hub.
[OFF]:6:00 or 6:00 AM)
AUTO:Dimmer turns on and off automatically when you turn off or on the car Connecting a cable whose total length is longer than 5m may result in abnormal playback.
headlights. *1 The maximum number of characters for:
- Folder names: 64 characters
BRIGHTNESS Set the button, display and USB input terminal brightness for day and night - File names: 64 characters
separately. - MP3 Tag: 64 characters
1 DAY / NIGHT:Select day or night. - WMA Tag: 64 characters
2 Select a zone.
- WAV Tag: 64 characters
3 Set the brightness level (00 to 31). (Default: DAY:31; NIGHT:15)
- FLAC Tag: 64 characters
SCROLL *2 ONCE:Scrolls the display information once.; AUTO:Repeats scrolling at This unit can recognize a total of 15 000 files, 500 folders (999 files per folder including folder
5-second intervals.; OFF:Cancels. without unsupported files), and of 8 hierarchies.
*1 The illumination control wire connection is required. ( 15) This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
*2 Some characters or symbols will not be shown correctly (or will be blanked).

ENGLISH 11

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 11 18/8/2015 10:33:16 AM
Book Size: B6L (182 mm x 128 mm)
REFERENCES
About iPod/iPhone Change the display information
Made for Each time you press , the display information changes.
- iPod touch (2nd, 3rd, 4th, and 5th generation) If the information is unavailable or not recorded, NO TEXT, NO NAME, or other
- iPod classic information (eg. station name) appears.
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
FM or AM Frequency Day/Clock
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus
It is not possible to browse video files on the Videos menu in [HEAD MODE]. (For FM Radio Data System stations only)
The song order displayed on the selection menu of this unit may differ from that of the iPod/ Station name (PS) Frequency Program type (PTY) Radiotext+
iPhone. Day/Clock (back to the beginning)
Depending on the version of the operating system of the iPod/iPhone, some functions may
USB (For MP3/WMA/WAV/FLAC files)
not operate on this unit.
Playing time Day/Clock Album title/Artist Track title
Folder/file name (back to the beginning)
About Android device
This unit supports Android OS 4.1 and above. USB-IPOD Playing time Day/Clock Album title/Artist Track title
Some Android devices (with OS4.1 and above) may not fully support Android Open Accessory or ANDROID (back to the beginning)
(AOA)2.0. AUX AUX Day/Clock
If the Android device supports both mass storage class device and AOA2.0, this unit always
playback via AOA2.0 as priority. BT AUDIO BT AUDIO Day/Clock

Available Cyrillic letters


Available characters
Display indications

12

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 12 18/8/2015 10:33:16 AM
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom Remedy Symptom Remedy
Sound cannot be heard. Adjust the volume to the optimum level. Sound cannot Reconnect the Android device.
Check the cords and connections. be heard during If in [AUDIO MODE], launch any media player
playback. application on the Android device and start playback.
MISWIRING CHECK WIRING Turn the power off, then check to be sure the terminals of Sound output only If in [AUDIO MODE], relaunch the current media player
General

THEN PWR ON appears. the speaker wires are insulated properly. Turn the power from the Android application or use another media player application.
on again. device. Restart the Android device.
PROTECTING SEND Send the unit to the nearest service center. If this does not solve the problem, the connected Android
SERVICE appears. device is unable to route the audio signal to unit. ( 12)

Source cannot be selected. Check the [SRCSELECT] setting. ( 4) Cannot playback at Make sure JVC MUSIC PLAY APP is installed on the
[AUTO MODE]. Android device. ( 7)
Radio reception is poor. Connect the antenna firmly. Reconnect the Android device and select the appropriate
Radio

ANDROID
Static noise while listening control mode. ( 8)
to the radio. If this does not solve the problem, the connected Android
device does not support [AUTO MODE]. ( 12)
Playback order is not as The playback order is determined by the file name.
intended. NO DEVICE or Switch off the developer options on the Android device.
READING keeps Reconnect the Android device.
Elapsed playing time is not This depends on the recording process earlier. flashing. If this does not solve the problem, the connected Android
correct. device does not support [AUTO MODE]. ( 12)
NOT SUPPORT appears and Check whether the file is a playable format. ( 11) Playback is intermittent Turn off the power saving mode on the Android device.
file skips. or sound skips.
READING keeps flashing. Do not use too many hierarchical levels and folders. CANNOT PLAY Make sure Android device contains playable audio files.
USB / iPod

Reattach the USB device. Reconnect the Android device.


CANNOT PLAY flashes and/ Check whether the connected device is compatible with this Restart the Android device.
or connected device cannot unit and ensure the files are in supported formats. ( 11)
be detected. Reattach the device. If you still have troubles, reset the unit. ( 3)
The iPod/iPhone does not Check the connection between this unit and iPod/iPhone.
turn on or does not work. Detach and reset the iPod/iPhone using hard reset.
Correct characters are not This unit can only display uppercase letters, numbers, and
displayed. a limited number of symbols.
Depending on the display language you have selected
( 4), some characters may not be displayed correctly.

ENGLISH 13

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_1a.indd 13 4/9/2015 9:42:54 AM
Book Size: B6L (182 mm x 128 mm)
INSTALLATION / CONNECTION Warning
The unit can only be used with a 12V DC power supply, negative ground.
Installing the unit (in-dash mounting)
Disconnect the batterys negative terminal before wiring and mounting.
Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit. Do the required wiring.
Insulate unconnected wires with vinyl tape to prevent a short circuit. ( 15)
Be sure to ground this unit to the cars chassis again after installation.
Caution
For safetys sake, leave wiring and mounting to professionals. Consult
the car audio dealer. Hook on the top side
Install this unit in the console of your vehicle. Do not touch the metal
Dashboard of
parts of this unit during and shortly after use of the unit. Metal parts such
Orientate the trim plate as your car
as the heat sink and enclosure become hot.
Do not connect the wires of speakers to the car chassis or Ground wire illustrated before fitting.
(black), or connect them in parallel.
Connect speakers with a maximum power of more than 50W. If the
maximum power of the speakers is lower than 50W, change the Bend the appropriate tabs to
[AMPGAIN] setting to avoid damaging the speakers. ( 10) hold the sleeve firmly in place.
Mount the unit at an angle of less than 30.
If your vehicle wiring harness does not have the ignition terminal,
When installing without the mounting sleeve
connect Ignition wire (red) to the terminal on the vehicles fuse box
1 Remove the mounting sleeve and trim plate
which provides 12 V DC power supply and is turned on and off by the
from the unit.
ignition key.
2 Align the holes in the unit (on both sides) with
Keep all cables away from heat dissipate metal parts.
the vehicle mounting bracket and secure the
After the unit is installed, check whether the brake lamps, blinkers,
unit with screws (commercially available).
wipers, etc. on the car are working properly.
Use only the specified screws. Using wrong screws might damage
If the fuse blows, first make sure the wires are not touching cars chassis,
the unit.
then replace the old fuse with one that has the same rating.
Basic procedure How to remove the unit
1 Remove the key from the ignition switch, then
disconnect the terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. ( 15)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery.
5 Reset the unit. ( 3)
14

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 14 18/8/2015 10:33:17 AM
Book Size: B6L (182 mm x 128 mm)
Wiring connection When connecting to an external
Rear/subwoofer output amplifier, connect its ground wire to the
cars chassis to avoid damaging the unit.

Part list for


Fuse (10A) Antenna terminal installation
(A) Faceplate

Connecting the ISO connectors on some VW/ If no connections are made, do not let the wire
Audi or Opel (Vauxhall) automobiles Yellow (Battery wire) come out from the tab.
You may need to modify the wiring of the (B) Trim plate
supplied wiring harness as illustrated below. Light blue/yellow To the steering wheel
Red (Ignition wire) (Steering remote
STEERING
WHEEL remote control adapter
REMOTE
control wire)
Ignition wire
A7 (Red) (Red) Pin Color and function
A2 Brown : Mobile phone system (C) Mounting sleeve
Vehicle Unit
A4 Yellow : Battery
A4 (Yellow) Battery wire Red (A7) A5 Blue/White : Power control
(Yellow)
A6 Orange/white : Car light control switch
Default wiring Yellow (A4) A7 Red : Ignition (ACC)
A8 Black : Earth (ground) connection (D) Wiring harness
B1 Purple ]
: Rear speaker (right)
* You can also connect a subwoofer speaker directly without B2 Purple/black [
an external subwoofer amplifier. For setting, 10. B3 Gray ]
: Front speaker (right)
B4 Gray/black [
If your car does not have an ISO terminal B5 White ]
We recommend installing the unit with a commercially available : Front speaker (left) (E) Extraction key
B6 White/black [
custom wiring harness specific for your car and leave this job to
professionals for your safety. Consult your car audio dealer. B7 Green ]
ISO connectors : Rear speaker (left) *
B8 Green/black [

ENGLISH 15

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_1a.indd 15 4/9/2015 9:55:24 AM
Book Size: B6L (182 mm x 128 mm)
SPECIFICATIONS
FM Frequency Range

Auxiliary
87.5MHz 108.0MHz (50kHz step) Frequency Response (3dB) 20Hz20kHz
Usable Sensitivity (S/N=26dB) 0.71V/75 Input Maximum Voltage 1000mV
Quieting Sensitivity 2.0V/75 Input Impedance 30k
(DINS/N=46dB)
Maximum Output Power 50W4 or
Frequency Response (3dB) 30Hz 15kHz 50W2 + 50W1 (Subwoofer = 4)
Tuner

Signal-to-Noise Ratio (MONO) 64dB Full Bandwidth Power 22W4

Audio
Stereo Separation (1kHz) 40dB (at less than 1% THD)
MW Frequency Range 531kHz 1611kHz (9kHz step) Speaker Impedance 48
Usable Sensitivity (S/N=20dB) 28.2V Preout Level/Load (USB) 2500mV/10k
LW Frequency Range 153kHz 279kHz (9kHz step) Preout Impedance 600
Usable Sensitivity (S/N=20dB) 50V
Operating Voltage 14.4V
USB Standard USB1.1, USB2.0 (Full speed) (10.5V16V allowable)

General
Compatible Devices Mass storage class Maximum Current Consumption 10A

File System FAT12/16/32 Operating Temperature Range 10C +60C

Maximum Supply Current DC5V 1A Installation Size (WHD) 182mm53mm107mm

D/A Converter 24 Bit Weight 0.6kg


Frequency Response (1dB) 20Hz 20kHz Subject to change without notice.
Signal-to-Noise Ratio (1kHz) 105dB
USB

Dynamic Range 88dB


Channel Separation 90dB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
WAV Decode RIFF waveform Audio Format (Linear PCM
only)
FLAC Decode FLAC files

16

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 16 18/8/2015 10:33:17 AM
Book Size: B6L (182 mm x 128 mm)
17

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_EN_Pre.indd 17 18/8/2015 10:33:17 AM
Book Size: B6L (182 mm x 128 mm)
TABLE DES MATIERES AVANT LUTILISATION
AVANT LUTILISATION 2 IMPORTANTES
Pour utiliser correctement lappareil, veuillez ce manuel complment avant de lutiliser. Il est particulirement important que
FONCTIONNEMENT DE BASE 3 vous lisiez et acceptiez les avertissements et les prcautions de ce manuel.
PRISE EN MAIN 4 Veuillez garder ce manuel dans un endroit sr et accessible pour une utilisation future.
1 Annulez la dmonstration Avertissement
2 Rglez lhorloge Nutilisez aucune fonction qui risque de vous distraire de la conduite sure de votre vhicule.
3 Faites les rglages de base Prcautions
Rglage du volume:
RADIO 5 Ajustez le volume de faon pouvoir entendre les sons extrieurs la voiture afin dviter tout risque daccident.
AUX 6 Rduisez le volume avant de reproduire des sources numriques afin dviter dendommager les enceintes par la soudaine
augmentation du niveau de sortie.
USB / iPod / ANDROID 7 Gnralits:
viter dutiliser le priphrique extrieur sil peut gner une conduite en toute scurit.
RGLAGES AUDIO 9 Assurez-vous que toutes les donnes importantes ont t sauvegardes. Nous ne pouvons pas tre tenu responsable pour toute
perte des donnes enregistres.
RGLAGES DAFFICHAGE 11 Veuillez faire en sorte de ne jamais mettre ou laisser dobjets mtalliques (tels que des pices ou des outils) dans lappareil, afin
RFRENCES 11 dviter tout risque de court-circuit.
Entretien
Plus dinformations
GUIDE DE DPANNAGE 13
INSTALLATION /
RACCORDEMENT 14
SPCIFICATIONS 16

Comment lire ce manuel


Les oprations sont expliques principalement en utilisant les touches de la faade du KD-X230.
Les indications en anglais sont utilises dans un but explicatif. Vous pouvez choisir la langue daffichage partir du menu.
( 4)
[XX] indique les lments choisis.
( XX) indique que des rfrences sont disponibles aux page cites.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 2 21/9/2015 2:11:56 PM
Book Size: B6L (182 mm x 128 mm)
FONCTIONNEMENT DE BASE
Faade Attachez

Bouton de
volume Fentre daffichage

Dtachez
KD-X130
TI ST

Comment rinitialiser
Touche de
dtachement

Vos ajustements prrgls seront effacs


sauf les stations radio mmorises.

Pour Sur la faade


Mettez lappareil sous tension Appuyez sur .
Maintenez la touche enfonce pour mettre lappareil hors tension.
Ajustez le volume Tournez le bouton de volume.
Appuyez sur le bouton de volume pour couper le son ou mettre la lecture en pause.
Appuyez une nouvelle fois pour annuler.

Slectionner la source Appuyez rptitivement sur .


Appuyez sur , puis tournez le bouton de volume avant 2 secondes.
Changez linformation sur laffichage Appuyez rptitivement sur . ( 12)

FRANAIS 3

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 3 21/9/2015 2:11:56 PM
Book Size: B6L (182 mm x 128 mm)
PRISE EN MAIN
3 Faites les rglages de base
1 Maintenez enfonce .
2 Tournez le bouton de volume pour slectionner un lment (voir le tableau
suivant), puis appuyez sur le bouton.
3 Rptez ltape 2 jusqu ce que llment souhait soit slectionn ou
activ.
4 Appuyez sur pour quitter.
1 Annulez la dmonstration Pour retourner loption de rglage prcdente, appuyez sur .
Quand vous mettez lappareil sous tension (ou aprs une rinitialisation de Dfaut: XX
lappareil), laffichage apparat: CANCEL DEMO PRESS VOLUME KNOB
SETTINGS
1 Appuyez sur le bouton de volume.
[YES] est choisi pour le rglage initial. BEEP ON:Met en service la tonalit des touches.; OFF:Met hors service la fonction.
2 Appuyez de nouveau sur le bouton de volume. SRC SELECT
DEMO OFF apparat.
AM * ON:Met en service AM dans la slection de la source.; OFF:Hors service.
2 Rglez lhorloge AUX * BTADAPTER:Slectionne ce rglage quand ladaptateur Bluetooth KS-BTA100 est connect la
prise AUX. ( 6); ON:Met en service AUX dans la slection de la source.; OFF:Hors service.
1 Maintenez enfonce .
2 Tournez le bouton de volume pour choisir [CLOCK], puis appuyez sur le F/W UPDATE
bouton. SYSTEM
3 Tournez le bouton de volume pour choisir [CLOCKSET], puis appuyez
sur le bouton. F/W xxxx YES:Dmarrer la mise niveau du micrologiciel.; NO:Annulation (la mise niveau nest pas
4 Tournez le bouton de volume pour faire les rglages, puis appuyez active).
sur le bouton. Pour en savoir plus sur la mise niveau du micrologiciel, rfrez-vous :
Jour Heure Minute <http://www.jvc.net/cs/car/>.
5 Tournez le bouton de volume pour choisir [24H/ 12H], puis appuyez CLOCK
sur le bouton.
6 Tournez le bouton de volume pour choisir [12 HOUR] ou [24 HOUR], puis CLOCK SYNC AUTO:Lhorloge est rgle automatiquement laide des donnes dhorloge (CT) comprises dans
appuyez sur le bouton. les donnes du signal FM Radio Data System.; OFF:Annulation.
7 Appuyez sur pour quitter.
CLOCK DISP ON:Lhorloge apparat sur laffichage mme quand lappareil est hors tension.; OFF:Annulation.
Pour retourner loption de rglage prcdente, appuyez sur .
ENGLISH
Slectionnez la langue daffichage pour le menu et linformation sur le morceau si elle est
disponible.
Par dfaut, ENGLISH est slectionn.
ESPANOL
* Pas daffichage quand la source correspondante est slectionne.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 4 21/9/2015 2:11:57 PM
Book Size: B6L (182 mm x 128 mm)
RADIO
Autres paramtres
1 Maintenez enfonce .
2 Tournez le bouton de volume pour choisir [TUNER], puis
appuyez sur le bouton.
3 Tournez le bouton de volume pour slectionner un lment
(voir le tableau suivant), puis appuyez sur le bouton.
4 Rptez ltape 3 jusqu ce que llment souhait soit
ST sallume lors de la rception dune mission FM stro avec un signal suffisamment fort. slectionn/activ ou suivez les instructions donnes pour
llment slectionn.
5 Appuyez sur pour quitter.
Recherchez une station Pour retourner loption de rglage prcdente, appuyez sur .
1 Appuyez rptitivemenent sur pour slectionner FM ou AM.
2 Appuyez sur pour rechercher une station automatiquement. Dfaut: XX
(ou)
Maintenez en enfonc jusqu ce que M clignote, puis appuyez rptitive RADIO TIMER Met la radio sous tension une heure spcifique quelle que soit la source
ment dessus pour rechercher une station manuellement. actuelle.
1 ONCE/ DAILY/ WEEKLY/ OFF:Slectionnez la frquence de mise
en service de la minuterie.
Rglages en mmoire 2 FM/ AM:Choisissez la bande.
Vous pouvez mmoriser un maximum de 18 stations pour FM et de 6 stations pour AM. 3 01 18 (pour FM)/ 01 06 (pour AM):Slectionnez la station
prrgle.
Mmorisez une station 4 Rglez lheure et le jour *1 de mise en service.
M sallume quand le rglage est termin.
Pendant lcoute dune station....
La minuterie de radio ne se met pas en service dans les cas suivants.
Maintenez presse une des touches numriques (1 6).
Lappareil est mis hors tension.
(ou)
1 Maintenez enfonc le bouton de volume jusqu ce que PRESETMODE clignote. [OFF] est slectionn pour [AM] dans [SRCSELECT] aprs la
2 Tournez le bouton de volume pour choisir un numro de prrglage, puis appuyez slection de la minuterie de radio pour AM. ( 4)
sur le bouton. SSM SSM0106 / SSM0712 / SSM1318: Prrgle
Le numro de prrglage clignote et MEMORY apparat. automatiquement un maximum de 18 stations pour FM. SSM sarrte de
clignoter quand les 6 premires stations sont mmorises. Slectionnez
Slectionnez une station mmorise SSM0712 / SSM1318 pour mmoriser les 12 stations
Appuyez sur lune des touches numriques (16). suivantes.
(ou) *1 Slectionnable uniquement quand [ONCE] ou [WEEKLY] est choisi ltape 1.
1 Appuyez sur .
2 Tournez le bouton de volume pour choisir un numro de prrglage, puis appuyez
sur le bouton pour valider.

FRANAIS 5

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 5 21/9/2015 2:11:57 PM
Book Size: B6L (182 mm x 128 mm)
RADIO AUX
Dfaut: XX
Utilisation dun lecteur audio portable
LOCAL SEEK ON:Recherche uniquement les stations FM avec une bonne rception.; OFF:Annulation. 1 Connectez un lecteur audio portable (en vente dans le commerce).
Les rglages raliss sont applicables uniquement la source/station slectionne. Si vous
changez la source/station, vous devez refaire les rglages. Mini fiche stro de 3,5 mm avec connecteur en forme de L
(en vente dans le commerce)
IF BAND AUTO:Augmente la slectivit du tuner pour rduire les interfrences des stations FM
adjacentes. (Leffet stro peut tre perdu.); WIDE:Il y a des interfrences des stations FM
adjacentes, mais la qualit du son nest pas dgrade et leffet stro est conserv.
MONO ON:Amliore la rception FM mais leffet stro sera perdu.; OFF:Annulation.
Prise dentre auxiliaire Lecteur audio portable
NEWS-STBY*2 ON:Lappareil commute temporairement sur le programme dinformation sil est disponible.;
OFF:Annulation. 2 Slectionnez [ON] pour [AUX] dans [SRC SELECT]. ( 4)
REGIONAL*2 ON: Commute sur une autre station uniquement dans la rgion spcifie, laide de la 3 Appuyez rptitivement sur pour slectionner AUX.
4 Mettez sous tension le lecteur audio portable et dmarrez la lecture.
commande AF.; OFF:Annulation.
AF SET*2 ON: Recherche automatiquement une autre station diffusant le mme programme dans le
mme rseau Radio Data System mais qui possde une meilleure rception quand la rception Utilisez une mini fiche stro munie dune fiche 3 connecteurs pour
actuelle est mauvaise.; OFF: Annulation. obtenir une sortie audio optimum.

TI SET*2 ON: Permet lappareil de commuter temporairement sur les informations routires si elles
sont disponibles (TI sallume). ; OFF:Annulation.
Utilisation dun priphrique Bluetooth
PTY SEARCH*2 Slectionnez un code PTY (voir ci-dessous). 1 Connectez ladaptateur Bluetooth, KS-BTA100 (vendu sparment).
Sil y a une station diffusant un programme du code PTY que vous avez choisi, la station est
accorde. Faisceau de fils de lappareil
( 15)
Code PTY: NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, Bleu/blanc
POP M (musique), ROCK M (musique), EASY M (musique), LIGHT M (musique), CLASSICS, Bleu/blanc: Tlcommande
OTHER M (musique), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, Noir
Noir: Masse
TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (musique), OLDIES, FOLK M (musique),
Marron
DOCUMENT Marron: Sourdine tlphonique

*2 Uniquement pour la source FM. Prise dentre auxiliaire


2 Enregistrement (pairage) dun appareil Bluetooth avec le KS-BTA100.
3 Slectionnez [BT ADAPTER] pour [AUX] dans [SRC SELECT]. ( 4)
4 Appuyez rptitivement sur pour slectionner BT AUDIO.
5 Commencez utiliser le priphrique Bluetooth.
Pour plus de dtails, se reporter au manuel dinstructions du KS-BTA100.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 6 21/9/2015 2:11:57 PM
Book Size: B6L (182 mm x 128 mm)
USB / iPod / ANDROID
Source slectionnable:
Dmarrez la lecture
KD-X230:
La source change automatiquement et le lecture USB/ USB-IPOD/ ANDROID KD-X130
dmarre. KD-X130:
USB/ ANDROID
Prise dentre USB
USB
KD-X230: Pour slectionner directement la source USB/ USB-IPOD/ ANDROID, appuyez sur .

Cble USB 2.0*1 Pour Sur la faade


(en vente dans le commerce) Recherche rapide vers larrire / Maintenez enfonce .
vers lavant*3
iPod/iPhone
Slectionnez un fichier Appuyez sur .
Slectionnez un dossier*4 Appuyez sur .

(Accessoire du Rpter la lecture*5 Appuyez rptitivement sur .


iPod/iPhone)*1 TRACK RPT/ FOLDER RPT/ ALL RPT : Fichier MP3/WMA/WAV/FLAC
ONE RPT/ ALL RPT/ RPT OFF : iPod ou ANDROID
Lecture alatoire*5 Appuyez rptitivement sur .
ANDROID*2 FOLDERRND/ ALL RND/ RND OFF : Fichier MP3/WMA/WAV/FLAC
SONG RND/ ALL RND/ RND OFF : iPod ou ANDROID
*1 Ne laissez pas le cble lintrieur de la voiture quand il nest pas utilis.
*2 Lors de la connexion dun priphrique Android, Press [VIEW] to install JVC MUSIC PLAY APP apparat. Suivez les instructions pour
Cble Micro USB 2.0*1 installer lapplication. Vous pouvez aussi intaller la dernire version de lapplication JVC MUSIC PLAY sur votre priphrique Android avant
(en vente dans le commerce) la connexion. ( 11)
*3 Pour ANDROID: Fonctionne uniquement quand [AUTO MODE] est slectionn. ( 8)
*4 Uniquement pour les fichiers MP3/WMA/WAV/FLAC. Cela ne fonctionne pas pour liPod/ ANDROID.
*5 Pour liPod/ ANDROID: Fonctionne uniquement quand [HEAD MODE]/ [AUTO MODE] est slectionn. ( 8)

FRANAIS 7

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 7 21/9/2015 2:11:57 PM
Book Size: B6L (182 mm x 128 mm)
USB / iPod / ANDROID

Slectionnez le mode de commande Slectionnez un fichier partir dun dossier/liste


Quand la source est USB-IPOD, appuyez rptitivement sur . 1 Appuyez sur .
HEAD MODE: Commande liPod partir de cet appareil. 2 Tournez le bouton de volume pour slectionner un dossier/liste, puis
IPHONE MODE: Commande liPod en utilisant liPod lui-mme. Cependant, vous pouvez appuyez sur le bouton.
encore utiliser la lecture/pause ou le saut de fichier de cet appareil. 3 Tournez le bouton de volume pour choisir un fichier, puis appuyez
sur le bouton.
Quand la source est ANDROID, appuyez rptitivement sur .
AUTO MODE: Commandez le priphrique Android partir de cet appareil via Recherche rapide
lapplication JVC MUSIC PLAY installe sur le priphrique Android. Si vous avez beaucoup de fichiers, vous pouvez effectuer une recherche
AUDIO MODE: Commandez le priphrique Android en utilisant le priphrique Android rapide parmi eux.
lui-mme via une autre application multimdia installe sur le priphrique Tournez rapidement le bouton de volume pour parcourir la liste
Android. Cependant, vous pouvez encore utiliser la lecture/pause ou le saut rapidement.
de fichier de cet appareil. Ne peut pas tre utilis pour iPod.

Recherche alphabtique (applicable uniquement pour iPod):


Slectionnez le lecteur de musique Vous pouvez rechercher un fichier en fonction du premier caractre.
Appuyez rptitivement sur . Appuyez sur ou tournez le bouton de volume
Les morceaux mmoriss dans le lecture suivant seront lus. rapidement pour slectionner le caractre souhait (A Z/ 0 9/
Mmoire interne ou smartphone (Mass Storage Class) slectionn. OTHERS).
Lecteur slectionn parmi plusieurs lecteurs. Slectionnez OTHERS si le premier caractre est autre que A Z, 0 9.
Pour retourner loption de rglage prcdente, appuyez sur .
Change la vitesse de lecture des livres audio Pour annuler, maintenez enfonce .
Pour liPod, applicable uniquement quand [HEADMODE] est slectionn.
Pendant lcoute de liPod et quand [HEADMODE] est slectionn.... Pour ANDROID, applicable uniquement quand [AUTO MODE] est slectionn.
1 Maintenez enfonce .
2 Tournez le bouton de volume pour choisir [IPOD], puis appuyez sur le
bouton.
3 Appuyez sur le bouton de volume pour slectionner [AUDIOBOOKS].
4 Tournez le bouton de volume pour choisir un lment, puis appuyez sur le
bouton.
0.5SPEED / 1SPEED / 2SPEED: Choisissez la vitesse de lecture souhait du fichier
sonore des livres audio dans votre iPod/iPhone.
(Dfaut: Dpend du rglage de votre iPod/iPhone.)
5 Appuyez sur pour quitter.
Pour retourner loption de rglage prcdente, appuyez sur .

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 8 21/9/2015 2:11:58 PM
Book Size: B6L (182 mm x 128 mm)
RGLAGES AUDIO
Dfaut: XX
EQSETTING
EQPRESET Slectionne un galiseur prrgl adapt votre genre de musique. (Slectionnez [USER] pour
utiliser les rglages raliss dans [EASY EQ].)
FLAT(dfaut) / HARD ROCK/ HIP HOP/ JAZZ/ POP/ R&B/ TALK/ USER/
VOCALBOOST/ BASSBOOST/ CLASSICAL/ DANCE

Choisissez un galiseur prrgl EASYEQ Ajustez vos propres ajustements sonores. Les rglages sont mmoriss dans [USER].
SUB.W SP *1*2: 00+06 (Dfaut: 03
Appuyez rptitivement sur . SUB.W *1*3: 08+08 00
(ou)
Appuyez sur , puis tournez le bouton de volume avant 5 secondes. BASSLVL: 06+06 00
MIDLVL: 06+06 00
galiseur prrgl: FLAT (dfaut), HARD ROCK, HIP HOP, JAZZ, POP, R&B, TALK, USER, TRELVL: 06+06 00)
VOCAL BOOST, BASS BOOST, CLASSICAL, DANCE
PRO EQ 1 BASS / MIDDLE / TREBLE:Choisissez une tonalit de son.
2 Ajustez les lments sonores de la tonalit de son choisie.
Mmorisez vos propres ajustements sonores BASS Frquence: 60/ 80/ 100/ 200HZ (Dfaut: 80HZ
1 Maintenez press pour accder au rglage EASY EQ. Niveau: 06 +06 00
2 Tournez le bouton de volume pour choisir un lment, puis appuyez sur Q: Q1.0/ Q1.25/ Q1.5/ Q2.0 Q1.0)
le bouton. MIDDLE Frquence: 0.5/ 1.0/ 1.5/ 2.5KHZ (Dfaut: 1.0KHZ
Reportez-vous [EASYEQ] pour le rglage et le rglage est mmoris dans [USER]. Niveau: 06 +06 00
Pour retourner loption de rglage prcdente, appuyez sur . Q: Q0.75/ Q1.0/ Q1.25 Q1.25)
Pour quitter, appuyez sur . TREBLE Frquence: 10.0/ 12.5/ 15.0/ 17.5KHZ (Dfaut: 10.0KHZ
Niveau: 06 +06 00
Autres paramtres Q: QFIX QFIX)

1 Maintenez enfonce . AUDIO


2 Tournez le bouton de volume pour slectionner un lment (voir le BASS BOOST +01+05(+01): Choisit votre niveau prfr daccentuation des graves.;
tableau suivant), puis appuyez sur le bouton. OFF:Annulation.
3 Rptez ltape 2 jusqu ce que llment souhait soit slectionn/
activ ou suivez les instructions donnes pour llment slectionn. LOUD 01/02:Accentue les basses ou hautes frquences pour produire un son plus quilibr aux faibles
4 Appuyez sur pour quitter. niveaux de volume.; OFF:Annulation.
Pour retourner loption de rglage prcdente, appuyez sur . *1 Affich uniquement quand [SUB.W] est rgl sur [ON]. ( 10)
*2 Affich uniquement quand [SPK/PREOUT] est rgl sur [SUB.W/SUB.W]. ( 10)
*3 Affich uniquement quand [SPK/PREOUT] est rgl sur [REAR/SUB.W] ou [SUB.W/SUB.W].
( 10)

FRANAIS 9

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 9 21/9/2015 2:11:58 PM
Book Size: B6L (182 mm x 128 mm)
RGLAGES AUDIO
*4 Affich uniquement quand [SUB.W] est rgl sur [ON].
SUB.W LEVEL *4 SPK-OUT *5 00+06(+03):Ajuste le niveau de sortie du caisson de grave
*5 Affich uniquement quand [SPK/PREOUT] est rgl sur [SUB.W/SUB.W].
connect par le cble denceinte. ( 15)
*6 Affich uniquement quand [SPK/PREOUT] est rgl sur [REAR/SUB.W] ou [SUB.W/SUB.W].
PRE-OUT *6 08+08(00):Ajuste le niveau de sortie du caisson de grave *7 Lajustement ne peut pas affecter la sortie du caisson de grave.
connect aux prises de sortie de ligne (REAR/SW) via un amplificateur *8 Ne fonctionne pas si [BTADAPTER] est slectionn pour [AUX] dans [SRCSELECT]. ( 4)
extrieur. ( 15)
SUB.W *6 ON/OFF: Active ou dsactive la sortie de caisson de grave. Rglages de sortie denceinte
SUB.WLPF *4 THROUGH:Tous les signaux sont envoys au caisson de grave. ; LOW 55HZ/ Slectionnez le rglage de sortie pour les enceintes [SPK/PRE OUT], sur la base de la
MID 85HZ/ HIGH120HZ:Les signaux audio avec des frquences infrieures 55Hz/ mthode de connexion des enceintes.
85Hz/ 120Hz sont envoys sur le caisson de grave.
SUB.WPHASE *4 REVERSE(180)/ NORMAL(0):Slectionne la phase de la sortie du caisson de grave Connexion via les prises de sortie de ligne
synchroniser avec la sortie des enceintes afin dobtenir des performances optimales. Pour les connexions via un amplificateur extrieur. ( 15)
(Peut tre uniquement slectionn si un rglage autre que [THROUGH] est choisi pour
[SUB.WLPF].) Rglage Signal audio via la prise de sortie de ligne
[SPK/PRE OUT] REAR/SW
FADER R06F06(00):Rgle la balance de sortie des enceintes avant et arrire.
REAR/REAR Sortie des enceintes arrire
BALANCE *7 L06R06(00):Rgle la balance de sortie des enceintes gauche et droite.
REAR/SUB.W Sortie de caisson de grave
VOLADJUST 15+06(00):Prrglez le niveau de volume initial de chaque source (en
comparaison avec le niveau de volume FM). Avant un ajustement, choisissez la source que SUB.W/SUB.W Sortie de caisson de grave
vous souhaitez ajuster. (VOLADJFIX apparat si FM est choisi.)
AMPGAIN LOWPOWER:Limite le volume maximum 25. (Choisissez ce rglage si la puissance Connexion via les cbles denceinte
maximum de chaque enceinte est infrieure 50 W pour viter tout dommage des Pour les connexions sans utiliser un amplificateur extrieur. Cependant, avec ces
enceintes.); HIGHPOWER:Le niveau de volume maximum est de 35. rglages vous pouvez aussi profiter de la sortie du caisson de grave. ( 15)
D.T.EXP ON:Cre un son raliste en compensant les composants haute frquence et en rtablissant Rglage Signal audio via le fil de lenceinte arrire
(Extension le temps de monte de la forme donde qui est perdu lors de la compression des donnes
numrique de [SPK/PRE OUT] L (gauche) R (droite)
audio.; OFF:Annulation.
plage) Sortie des enceintes arrire Sortie des enceintes arrire
REAR/REAR
TELMUTING *8 ON:Coupe le son pendant lutilisation dun tlphone portable (non connect par le REAR/SUB.W Sortie des enceintes arrire Sortie des enceintes arrire
KS-BTA100).; OFF:Annulation.
SUB.W/SUB.W Sortie de caisson de grave (Sourdine)
SPK/PREOUT En fonction de la mthode de connexion des enceintes, slectionner le rglage appropri pour
obtenir la sortie souhaite. ( Rglages de sortie denceinte) Si [SUB.W/SUB.W] est slectionn:
[HIGH120HZ] est slectionn dans [SUB.WLPF] et [THROUGH] nest pas disponible.
[R01] est slectionn dans [FADER] et la plage slectionnable est de [R06] [00].

10

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 10 21/9/2015 2:11:58 PM
Book Size: B6L (182 mm x 128 mm)
RGLAGES DAFFICHAGE RFRENCES
Entretien
Nettoyage de lappareil
Essuyez la salet de la faade avec un chiffon sec au silicone ou un chiffon doux.

Nettoyage du connecteur
Dtachez la faade et nettoyez le connecteur laide dun coton
1 Maintenez enfonce . tige en faisant attention de ne pas endommager le connecteur.
2 Tournez le bouton de volume pour slectionner un lment (voir le
tableau suivant), puis appuyez sur le bouton. Plus dinformations Connecteur (sur la face arrire
3 Rptez ltape 2 jusqu ce que llment souhait soit slectionn/ de la faade)
activ ou suivez les instructions donnes pour llment slectionn. Consultez aussi le site web suivant
4 Appuyez sur pour quitter. <http://www.jvc.net/cs/car/> pour:
Les dernires mise jour du micrologiciel et la liste de compatibilit la plus rcente
Pour retourner loption de rglage prcdente, appuyez sur . Application Android JVC MUSIC PLAY
Dfaut: XX Autres informations rcentes
DISPLAY
Fichiers pouvant tre lus
DIMMER Assombrit lclairage de laffichage de des touches. Fichier audio reproductible: MP3 (.mp3), WMA (.wma), WAV(.wav), FLAC (.flac)
OFF:Le gradateur est dsactiv. Systmes de fichier de priphrique USB compatibles: FAT12, FAT16, FAT32
ON:Le gradateur est activ. La luminosit change sur le rglage [NIGHT]. Mme quand les fichiers audio sont conformes aux normes tablies ci-dessus, il est possible que la lecture ne soit pas
( [BRIGHTNESS]) possible suivant le type ou les conditions du support ou priphrique.
DIMMER TIME:Rglez lheure de mise en et hors service du gradateur.
1 Tournez le bouton de volume pour rgler lheure de mise en service [ON], puis appuyez sur le propos des priphriques USB
bouton. Cet appareil peut reproduire les fichiers MP3/WMA/WAV/FLAC mmoriss sur un priphrique USB mmoire de
2 Tournez le bouton de volume pour rgler lheure de mise en service [OFF], puis appuyez sur grande capacit.
le bouton. Vous ne pouvez pas connecter un priphrique USB via un hub USB.
(Dfaut: [ON]: 18:00 ou 6:00 PM La connexion dun cble dont la longueur totale dpasse 5 m peut avoir pour consquence un fonctionnement
[OFF]: 6:00 ou 6:00 AM) anormal de la lecture.
AUTO:Le gradateur est activ et dsactiv automatiquement quand vous teignez ou allumez Nombre maximum de caractre pour:
les feux de la voiture. *1 - Noms de dossier: 64 caractres
- Noms de fichier: 64 caractres
BRIGHTNESS Rgle la luminosit des touches, de laffichage et de la prise dentre USB sparment pour le - Balises MP3: 64 caractres
jour et la nuit. - Balises WMA: 64 caractres
1 DAY / NIGHT:Choisissez le jour ou la nuit. - Balises WAV: 64 caractres
2 Choisissez une zone. - Balises FLAC: 64 caractres
3 Rglez le niveau de luminosit (00 31). (Dfaut: DAY:31; NIGHT:15) Cet appareil peut reconnatre un maximum de 15 000 fichiers, 500 dossiers (999 fichiers par dossier y compris les
SCROLL *2 ONCE:Fait dfiler une fois les informations de laffichage.; AUTO:Rpte le dfilement dossiers sans fichier) et 8 hirarchies.
5 secondes dintervalle.; OFF:Annulation. Cet appareil ne peut pas reconnatre les priphriques USB dont lalimentation nest pas de 5 V et dpasse 1 A.
*1 La connexion du fil de commande de lclairage est requise. ( 15)
*2 Certains caractres ou symboles napparaissent pas correctement (ou un blanc apparat leur place).
FRANAIS 11

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 11 21/9/2015 2:11:59 PM
Book Size: B6L (182 mm x 128 mm)
RFRENCES
propos de liPod/iPhone Changez linformation sur laffichage
Made for Chaque fois que vous appuyez sur , les informations affiches changent.
- iPod touch (2nd, 3rd, 4th et 5th generation) Si aucune information nest disponible ou si aucune information nest enregistre, NO TEXT, NO NAME, ou une
- iPod classic autre information (par ex. le nom de la station) apparat.
- iPod nano (3rd, 4th, 5th, 6th et 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus FM ou AM Frquence Jour/Horloge
Il nest pas possible de parcourir les fichiers vido sur le menu Videos en mode [HEAD MODE]. (Pour les stations FM Radio Data System uniquement)
Lordre des morceaux affichs sur le menu de slection de cet appareil peut tre diffrent de celui de iPod/iPhone. Nom de la station (PS) Frquence Type de programme (PTY) Radio texte+
En fonction de la version du systme dexploitation de liPod/iPhone, certaines fonctions peuvent ne pas tre Jour/Horloge (retour au dbut)
utilisables sur cet appareil.
USB (Pour les fichiers MP3/WMA/WAV/FLAC)
propos du priphrique Android Dure de lecture Jour/Horloge Titre dalbum/Artiste Titre de plage
Cet appareil prend en charge Android OS 4.1 et ultrieur. Noms de dossier/fichier (retour au dbut)
Certains priphriques Android (avec OS 4.1 et ultrieur) peuvent ne pas prendre en charge compltement Android
Open Accessory (AOA) 2.0. USB-IPOD Dure de lecture Jour/Horloge Titre dalbum/Artiste Titre de plage
Si le priphrique Android prend en charge la fois le protocole mass storage class et AOA 2.0, cet appareil utilise ou ANDROID (retour au dbut)
toujours en priorit la lecture via AOA 2.0. AUX Jour/Horloge
AUX
BT AUDIO BT AUDIO Jour/Horloge
Lettres cyrilliques disponibles
Caractres disponibles
Indications sur laffichage

12

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 12 21/9/2015 2:11:59 PM
Book Size: B6L (182 mm x 128 mm)
GUIDE DE DPANNAGE
Symptme Remde Symptme Remde
Le son ne peut pas tre entendu. Ajustez le volume sur le niveau optimum. Aucun son ne peut tre Reconnectez le priphrique Android.
Vrifiez les cordons et les connexions. entendu pendant la En mode [AUDIO MODE], lancez nimporte quelle application
lecture. multimdia sur le priphrique Android et dmarrez la lecture.
MISWIRING CHECK WIRING THEN Mettez lappareil hors tension, puis assurez-vous que les prises des cbles
Le son sort uniquement du En mode [AUDIO MODE], relancez lapplication multimdia actuelle
Gnralits

PWR ON apparat. denceinte sont correctement isoles. Mettez de nouveau lappareil sous
tension. priphrique Android. ou utilisez une autre application multimdia.
Redmarrez le priphrique Android.
PROTECTING SEND SERVICE Envoyez lappareil au centre de service le plus proche. Si cela ne rsout pas le problme, cest que le priphrique Android
apparat. connect ne peut pas diriger le signal audio sur lappareil. ( 12)
Vous ne pouvez pas choisir la source. Cochez le rglage [SRCSELECT]. ( 4) Lecture impossible en mode Assurez-vous que JVC MUSIC PLAY APP est install sur le priphrique
La rception radio est mauvaise. Connectez lantenne solidement. [AUTO MODE]. Android. ( 7)
Radio

Bruit statique pendant lcoute de Reconnectez le priphrique Android et slectionnez le mode de


commande appropri. ( 8)

ANDROID
la radio.
Si cela ne rsout pas le problme, cest que le priphrique Android
Lordre de lecture nest pas celui que Lordre de lecture est dtermin par le nom du fichier. connect ne prend pas en charge [AUTO MODE]. ( 12)
vous pensiez.
NO DEVICE ou READING Dactivez les options dveloppeur sur le priphrique Android.
La dure de lecture coule nest Cela dpend du processus denregistrement utilis. clignote sur. Reconnectez le priphrique Android.
pascorrecte. Si cela ne rsout pas le problme, cest que le priphrique Android
NOT SUPPORT apparat et la fichier Vrifiez si la fichier est dans un format compatible. ( 11) connect ne prend pas en charge [AUTO MODE]. ( 12)
est saute.
La lecture est intermittente Dactivez le mode dconomie dnergie sur le priphrique Android.
READING clignote sur. Nutilisez pas trop de niveaux de hirarchie et de dossiers. ou le son saute.
Reconnectez le USB priphrique.
CANNOT PLAY Assurez-vous que le priphrique Android contient des fichiers audio
USB / iPod

CANNOT PLAY clignote et/ou le Vrifiez si le priphrique connect est compatible avec cet appareil et compatibles.
priphrique connect ne peut pas assurez-vous que les fichiers sont dans un format compatible. ( 11) Reconnectez le priphrique Android.
etre dtect. Reconnectez le priphrique. Redmarrez le priphrique Android.
iPod/iPhone ne peut pas tre mis Vrifiez la connexion entre cet appareil et liPod/iPhone.
sous tension ou ne fonctionne pas. Dtachez et rinitialisez liPod/iPhone en utilisant un rinitialisation Si vous avez toujours des problme, rinitialisez lappareil. ( 3)
matrielle.
Les caractres corrects ne sont pas Cet appareil peut uniquement afficher les lettres majuscules, les chiffres
affichs. et un nombre limit de symboles.
En fonction de la langue daffichage que vous avez choisie ( 4),
certains caractres peuvent ne pas tre affichs correctement.

FRANAIS 13

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 13 21/9/2015 2:11:59 PM
Book Size: B6L (182 mm x 128 mm)
INSTALLATION / RACCORDEMENT Avertissement
Lappareil peut uniquement tre utilis avec une alimentation de 12 V CC, masse ngative.
Installation de lappareil (montage encastr)
Dconnectez la borne ngative de la batterie avant le cblage et le montage.
Ne connectez pas le fil de batterie (jaune) et le fil dallumage (rouge) au chssis de la
voiture ou au fil de masse (noir) pour viter les courts-circuits.
Isolez les fils non connects avec du ruban adhsif pour viter les courts-circuits. Ralisez les connexions
Assurez-vous de raccorder de nouveau la mise la masse de cet appareil au chssis de la ncessaires. ( 15)
voiture aprs linstallation.
Prcautions
Pour des raison de scurit, laissez le travail de cblage et de montage des professionnels. Crochet sur le ct
Consultez votre revendeur autoradio. suprieur
Installez cet appareil dans la console de votre vhicule. Ne touchez pas les parties
mtalliques de cet appareil pendant ou juste aprs son utilisation. Les parties mtalliques, Tableau de bord de
comme le dissipateur de chaleur et le botier, deviennent chaudes. Orientez la plaque de garniture de la votre voiture
Ne connectez pas les fils des lenceintes au chssis de la voiture, au fil de masse (noir) ou faon illustre avant la fixation.
en parallle.
Connectez des enceintes avec une puissance maximum de plus de 50 W. Si la puissance
maximum des enceintes est infrieure 50W, changez le rglage [AMPGAIN] pour
viter dendommager les enceintes. ( 10) Tordez les languettes appropries pour
Montez lappareil avec un angle de moins de 30. maintenir le manchon en place.
Si le faisceau de fils de votre vhicule ne possde pas de borne dallumage, connectez
le fil dallumage (rouge) la borne du botier de fusible de votre vhicule qui offre une
alimentation de 12 V CC et qui se met en et hors service avec la cl de contact. Lors dune installation sans manchon de
Gardez tous les cbles lcart des dissipateurs thermiques. montage
Aprs avoir install lappareil, vrifiez si les lampes de frein, les indicateurs, les clignotants, 1 Retirez le manchon de montage et la plaque
etc. de la voiture fonctionnent correctement. dassemblage de lappareil.
Si un fusible saute, assurez-vous dabord que les cbles ne touches pas le chssis de la 2 Alignez les entailles de lappareil (des deux cts)
voiture puis remplacez le vieux fusible par un nouveau de mme valeur. avec le support de montage du vhicule et fixez
lappareil avec les vis (en vente dans le commerce).
Procdure de base Nutiliser que les vis spcifis. Lutilisation de vis incorrects peut endommager
1 Retirez la cl de contact, puis dconnectez la borne lappareil.
de la batterie de la voiture.
2 Connectez les fils correctement.
Reportez-vous Connexions. ( 15) Comment retirer lappareil
3 Installez lappareil dans votre voiture.
Reportez-vous Installation de lappareil (montage encastr).
4 Connectez la borne de la batterie de la voiture.
5 Rinitialisez lappareil. ( 3)

14

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 14 21/9/2015 2:11:59 PM
Book Size: B6L (182 mm x 128 mm)
Connexions
Lors de la connexion un amplificateur extrieur,
Sortie arrire/caisson de grave connectez son fil de masse au chssis de la voiture
pour viter dendommager lappareil.

Liste des pices pour


Fusible (10 A) Borne de lantenne linstallation
(A) Faade

Connexion des connecteurs ISO sur certaines


Si aucune connexion nest faite, ne laissez pas le cble sortir
voitures VW/Audio ou Opel (Vauxhall) Jaune (Cble de batterie) de la languette.
Vous aurez peut-tre besoin de modifier le cblage du faisceau (B) Plaque dassemblage
de fils fourni comme montr sur lillustration ci-dessous. Bleu clair/jaune ladaptateur de
Rouge (Cble dallumage) (Fil de tlcommande STEERING
WHEEL
tlcommande volant
de volant) REMOTE

Cble dallumage
A7 (Rouge) (Rouge) Broche Couleur et fonction
Vhicule A2 Marron : Systme de tlphone portable (C) Manchon de montage
Appareil
A4 Jaune : Pile
A4 (Jaune) Cble de Rouge (A7) A5 Bleu/Blanc : Commande dalimentation
batterie (Jaune)
A6 Orange/blanc : clairage de la voiture
Cblage par dfaut A7 Rouge : Allumage (ACC)
Jaune (A4)
A8 Noir : Connexion la terre (masse) (D) Faisceau de fils
B1 Violet ]
: Enceinte arrire (droit)
* Vous pouvez aussi connecter directement un caisson de grave sans B2 Violet/noir [
amplificateur de caisson de grave extrieur. Pour les rglages, 10. B3 Gris ]
: Enceinte avant (droit)
B4 Gris/noir [
Si votre voiture ne possde pas de prise ISO B5 Blanc ]
Nous recommandons dinstaller lappareil en utilisant un harnais de cblage en : Enceinte avant (gauche)
B6 Blanc/noir [ (E) Cl dextraction
vente dans le commerce recommand spcifiquement pour votre voiture et, pour
votre scurit, de laisser ce travail a des professionnels. Consultez votre revendeur B7 Vert ]
Connecteurs ISO : Enceinte arrire (gauche) *
autoradio. B8 Vert/noir [

FRANAIS 15

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 15 21/9/2015 2:12:00 PM
Book Size: B6L (182 mm x 128 mm)
SPCIFICATIONS
FM

Auxiliaire
Plage de frquences 87,5MHz 108,0MHz (pas de 50kHz) Rponse en frquence (3 dB) 20Hz20kHz
Sensibilit utilisable (S/B = 26dB) 0,71 V/75 Tension maximum dentre 1000 mV
Seuil de sensibilit (DINS/N=46dB) 2,0 V/75 Impdance dentre 30k
Rponse en frquence (3 dB) 30Hz 15kHz Puissance de sortie maximum 50W4 ou
50W2 + 50W1 (Caisson de grave = 4)
Tuner

Taux de Signal/Bruit (MONO) 64 dB


Sparation stro (1 kHz) 40 dB Pleine Puissance de Largeur de Bande 22W4

Audio
(avec moins de 1% DHT)
PO Plage de frquences 531kHz 1611kHz (pas de 9kHz)
Impdance denceinte 48
Sensibilit utilisable (S/B = 20dB) 28,2V
Niveau de pramplification/charge (USB) 2500 mV/10k
GO Plage de frquences 153kHz 279kHz (pas de 9kHz)
Impdance du pramplificateur 600
Sensibilit utilisable (S/B = 20dB) 50V
Tension de fonctionnement 14,4V
Standard USB USB1.1, USB2.0 (Vitesse maximale) (10,5 V 16V admissible)

Gnralits
Priphriques compatibles mmoire de grande capacit Consommation de courant maximale 10A
Systme de fichiers FAT12/16/32 Gamme de temprature de fonctionnement 10C +60C
Courant dalimentation maximum CC5 V 1A Dimensions dinstallation (L H P) 182 mm53 mm107mm
Convertisseur D/A 24 Bit Poids 0,6kg
Rponse en frquence (1 dB) 20 Hz 20 kHz
Sujet changement sans notification.
Taux de Signal/Bruit (1 kHz) 105 dB
USB

Gamme dynamique 88 dB
Sparation des canaux 90 dB
Dcodage MP3 Compatible avec le format MPEG-1/2 Audio Layer-3
Dcodeur WMA Compatible Windows Media Audio
Dcodeur WAV Format audio de forme donde RIFF (PCM linaire
uniquement)
Dcodeur FLAC Fichiers FLAC

16

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_FR.indd 16 21/9/2015 2:12:00 PM
Book Size: B6L (182 mm x 128 mm)
JS_JVC_KD_X230_X130_E_FR.indd 17 21/9/2015 2:12:00 PM
INHALT VOR DER INBETRIEBNAHME
VOR DER INBETRIEBNAHME 2 WICHTIG
Um richtige Verwendung sicherzustellen, lesen Sie die Bedienungsanleitung vor der Verwendung des Produkts sorgfltig durch.
GRUNDLAGEN 3 Es ist besonders wichtig, dass Sie die als Warnung und Vorsicht gekennzeichneten Hinweise in dieser Anleitung lesen und
ERSTE SCHRITTE 4 beachten.
1 Brechen Sie die Bitte bewahren Sie die Anleitung an sicherer Stelle und griffbereit zum Nachschlagen auf.
Demonstration ab Warnung
2 Stellen Sie die Uhr ein Bedienen Sie keine Funktion, die Ihre Aufmerksamkeit vom Straenverkehr ablenkt.
3 Einstellen der Vorsicht
grundlegenden Lautstrkeeinstellung:
Einstellungen Stellen Sie die Lautstrke so ein, dass Sie immer noch Gerusche von auerhalb des Fahrzeugs hren knnen, um Unflle zu
vermeiden.
RADIO 5 Senken Sie die Lautstrke vor dem Abspielen digitaler Tonquellen, um Beschdigung der Lautsprecher durch pltzliche
Tonspitzen zu vermeiden.
AUX 6 Allgemeines:
USB / iPod / ANDROID 7 Vermeiden Sie Verwendung des externen Gerts, wenn dieses das sichere Fahren behindern kann.
Stellen Sie sicher, dass alle wichtigen Daten gesichert sind. Wir bernehmen keine Haftung fr jeglichen Verlust
AUDIOEINSTELLUNGEN 9 aufgenommener Daten.
Stellen Sie sicher, dass keine Metallgegenstnde (wie etwa Mnzen oder Werkzeuge) ins Innere des Gerts gelangen und
DISPLAY-EINSTELLUNGEN 11 Kurzschlsse verursachen.
ZUR BEZUGNAHME 11
Wartung
Weitere Informationen
FEHLERSUCHE 13
EINBAU / ANSCHLUSS 14
TECHNISCHE DATEN 16

Wie Sie diese Anleitung lesen


Die Bedienung wird im Wesentlichen anhand der Tasten auf der Frontblende des KD-X230 erlutert.
Englischsprachige Anzeigen werden zur Erklrung verwendet. Sie knnen die Anzeigesprache im Men whlen. ( 4)
[XX] zeigt die gewhlten Punkte an.
( XX) zeigt an, das Bezugsinformationen auf der angegebenen Seitennummer vorhanden sind.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 2 21/9/2015 2:16:14 PM
Book Size: B6L (182 mm x 128 mm)
GRUNDLAGEN
Frontblende Anbringen

Lautstrke-Regler Displayfenster

Abnehmen
KD-X130
TI ST

Rcksetzen
Abnehmen-Taste

Ihre aktuellen Voreinstellungen werden


gelscht, mit Ausnahme gespeicherter
Radiosender.

Zum Auf der Frontblende


Einschalten Drcken Sie .
Zum Ausschalten halten Sie die Taste gedrckt.
Einstellen der Lautstrke Drehen Sie den Lautstrke-Regler.
Drcken Sie den Lautstrke-Regler zum Stummschalten des Tons oder zum Pausieren der Wiedergabe.
Zum Abbrechen drcken Sie die Taste erneut.

Quelle auswhlen Drcken Sie wiederholt.


Drcken Sie , und drehen Sie dann den Lautstrke-Regler innerhalb von 2 Sekunden.
ndern der Display-Information Drcken Sie wiederholt. ( 12)

DEUTSCH 3

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 3 21/9/2015 2:16:15 PM
Book Size: B6L (182 mm x 128 mm)
ERSTE SCHRITTE
3 Einstellen der grundlegenden Einstellungen
1 Halten Sie gedrckt.
2 Drehen Sie den Lautstrke-Regler, um einen Gegenstand zu treffen (siehe
folgende Tabelle), und drcken Sie dann den Regler.
3 Wiederholen Sie Schritt 2, bis der gewnschte Gegenstand gewhlt oder
aktiviert ist.
4 Drcken Sie zum Beenden.
1 Brechen Sie die Demonstration ab Zum Zurckschalten zum vorherigen Einstellelement drcken Sie .
Wenn Sie die Stromversorgung einschalten (nach dem Rcksetzen des Gerts), Standard: XX
erscheint folgende Anzeige im Display: CANCEL DEMO PRESS
VOLUME KNOB SETTINGS
1 Drcken Sie den Lautstrke-Regler. BEEP ON:Aktiviert den Tastenberhrungston.; OFF:Deaktiviert.
[YES] ist fr das ursprngliche Setup gewhlt. SRC SELECT
2 Drcken Sie den Lautstrke-Regler erneut.
DEMO OFF erscheint. AM * ON:Aktiviert Sie AM in der Quellenwahl.; OFF:Deaktiviert.
AUX * BTADAPTER:Whlen Sie dies, wenn der KS-BTA100 Bluetooth-Adapter an die AUX-Buchse
2 Stellen Sie die Uhr ein angeschlossen ist. ( 6); ON:Aktiviert AUX in der Quellenwahl.; OFF:Deaktiviert.
1 Halten Sie gedrckt. F/W UPDATE
2 Drehen Sie den Lautstrke-Regler zum Whlen von [CLOCK], und SYSTEM
drcken Sie dann den Regler.
3 Drehen Sie den Lautstrke-Regler zum Whlen von [CLOCKSET], und F/W xxxx YES:Startet die Aktualisierung der Firmware.; NO:Hebt auf (Aktualisierung wird nicht
drcken Sie dann den Regler. ausgefhrt).
4 Drehen Sie den Lautstrke-Regler, um die Einstellungen Einzelheiten darber, wie Sie die Firmware aktualisieren knnen, siehe:
vorzunehmen, und drcken Sie dann den Regler. <http://www.jvc.net/cs/car/>.
Tag Stunde Minute CLOCK
5 Drehen Sie den Lautstrke-Regler zum Whlen von [24H/ 12H], und
drcken Sie dann den Regler. CLOCK SYNC AUTO:Die Uhrzeit wird automatisch mit den Uhrzeit-Daten (CT) im -Daten (Uhrzeit) im FM (UKW)
Radio Data System eingestellt.; OFF:Hebt auf.
6 Drehen Sie den Lautstrke-Regler zum Whlen von [12 HOUR] oder
[24 HOUR], und drcken Sie dann den Regler. CLOCK DISP ON:Die Uhrzeit wird im Display angezeigt, auch wenn das Gert ausgeschaltet wird.;
7 Drcken Sie zum Beenden. OFF:Hebt auf.
Zum Zurckschalten zum vorherigen Einstellelement drcken Sie . ENGLISH
Whlen Sie die Anzeigesprache fr das Men und die Musik-Information, wo zutreffend.

Als Standard ist ENGLISH ausgewhlt.
ESPANOL
* Nicht angezeigt, wenn die entsprechende Quelle gewhlt ist.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 4 21/9/2015 2:16:15 PM
Book Size: B6L (182 mm x 128 mm)
RADIO
Andere Einstellungen
1 Halten Sie gedrckt.
2 Drehen Sie den Lautstrke-Regler zum Whlen von [TUNER],
und drcken Sie dann den Regler.
3 Drehen Sie den Lautstrke-Regler, um einen Gegenstand
zu treffen (siehe folgende Tabelle), und drcken Sie dann
den Regler.
ST leuchtet auf, wenn eine UKW-Stereosendung mit ausreichender Signalstrke empfangen wird. 4 Wiederholen Sie Schritt 3, bis der gewnschte Gegenstand
gewhlt/aktiviert ist, oder folgen Sie den Anweisungen auf
dem gewhlten Gegenstand.
Suche nach einem Sender 5 Drcken Sie zum Beenden.
1 Drcken Sie wiederholt, um FM (UKW) oder AM zu whlen. Zum Zurckschalten zum vorherigen Einstellelement drcken Sie
2 Drcken Sie , um einen Sender automatisch zu suchen. .
(oder)
Halten Sie gedrckt, bis M blinkt, und drcken Sie die Taste dann Standard: XX
wiederholt, um einen Sender manuell zu suchen.
RADIO TIMER Schaltet das Radio zu einer spezifischen Zeit ein, ungeachtet der aktuellen
Quelle.
Einstellungen im Speicher 1 ONCE/ DAILY/ WEEKLY/ OFF:Whlen Sie, wie oft der Timer
eingeschaltet wird.
Sie knnen bis zu 18 Sender fr FM (UKW) und 6 Sender fr AM speichern.
2 FM/ AM:Whlen Sie das Frequenzband.
Speichern eines Senders 3 01 bis 18 (fr FM)/ 01 bis 06 (fr AM):Whlen Sie den Festsender.
4 Stellen Sie den Tag *1 und die Zeit der Aktivierung ein.
Whrend des Hrens eines Senders.... M leuchtet auf, wenn der Vorgang fertig ist.
Halten Sie eine der Zifferntasten (1bis 6) gedrckt.
Radio Timer wird in den folgenden Fllen nicht aktiviert.
(oder)
Das Gert ist ausgeschaltet.
1 Halten SIe den Lautstrke-Regler gedrckt, bis PRESETMODE blinkt.
2 Drehen Sie den Lautstrke-Regler zum Whlen einer Festsendernummer, und [OFF] ist fr [AM] in [SRCSELECT] gewhlt, nachdem Radio Timer
drcken Sie dann den Regler. fr AM gewhlt wurde. ( 4)
Die Festsendernummer blinkt, und MEMORY erscheint. SSM SSM0106 / SSM0712 / SSM1318: Automatische
Voreinstellung von bis zu 18 Sendern fr FM (UKW). SSM hrt zu
Whlen Sie einen gespeicherten Sender aus blinken auf, wenn die ersten 6 Sender gespeichert sind. Whlen Sie
Drcken Sie eine der Zifferntasten (1bis 6). SSM0712 / SSM1318 zum Speichern der folgenden
(oder) 12 Sender.
1 Drcken Sie . *1 Nur whlbar, wenn [ONCE] oder [WEEKLY] in Schritt 1 gewhlt wurde.
2 Drehen Sie den Lautstrke-Regler zum Whlen einer Voreingabenummer, und
drcken Sie dann den Regler zur Besttigung.

DEUTSCH 5

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 5 21/9/2015 2:16:16 PM
Book Size: B6L (182 mm x 128 mm)
RADIO AUX
Standard: XX
Verwendung eines tragbaren Audioplayers
LOCAL SEEK ON:Sucht nur FM (UKW)-Sender mit gutem Empfang.; OFF:Hebt auf. 1 Schlieen Sie einen tragbaren Audioplayer (im Handel erhltlich) an.
Die vorgenommenen Einstellungen gelten nur fr die gewhlte Quelle/den gewhlten
Sender. Wenn Sie die Quelle/den Sender gewechselt haben, mssen Sie die Einstellungen 3,5-mm-Stereo-Ministecker mit L-frmigem Anschluss
erneut vornehmen. (im Handel erhltlich)
IF BAND AUTO:Steigert die Tuner-Empfindlichkeit, um Strgerusche von benachbarten FM-Sendern
zu verringern. (Stereo-Effekt kann verlorengehen).; WIDE:Ist Interferenz von benachbarten
FM-Sendern ausgesetzt, aber die Klangqualitt wird nicht verringert, und der Stereoeffekt
wird bewahrt.
Auxiliary-Eingabebuchse Tragbarer Audioplayer
MONO ON:Verbessert den FM (UKW)-Empfang, aber der Stereoeffekt geht verloren.; OFF:Hebt auf.
2 Whlen Sie [ON] fr [AUX] in [SRC SELECT]. ( 4)
NEWS-STBY*2 ON:Das Gert schaltet kurzzeitig auf das Nachrichtenprogramm, falls verfgbar.; OFF:Hebt 3 Drcken Sie wiederholt zum Whlen von AUX.
auf. 4 Schalten Sie den tragbaren Audioplayer ein und starten Sie die
REGIONAL*2 ON: Schaltet auf einen anderen Sender in der spezifischen Region nur mit der AF-Steuerung.; Wiedergabe.
OFF:Hebt auf.
AF SET*2 ON: Sucht automatisch einen anderen Sender auf, der das gleiche Programm im gleichen Verwenden Sie einen 3-adrigen Stereo-Ministecker fr optimale
Radio Data System-Netzwerk sendet und einen besseren Empfang aufweist, falls der aktuelle Audioausgabe.
Empfang schlecht ist.; OFF: Hebt auf.
TI SET*2 ON: Erlaubt es, das Gert kurzzeitig auf Verkehrsinformation schalten, wenn verfgbar
(TI leuchtet auf). ; OFF:Hebt auf. Verwendung eines Bluetooth-Gerts
PTY SEARCH*2 Whlen Sie einen PTY-Code (siehe unten). 1 Schlieen Sie den Bluetooth-Adapter, KS-BTA100 an (separat erhltlich).
Wenn ein Sender eine Sendung mit dem PTY-Code ausstrahlt, den Sie gewhlt haben, wird Verdrahtungskabelbaum des
dieser Sender eingestellt. Gerts ( 15)
Blau/Wei
PTY-Codes: NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, Blau/Wei: Fernbedienung
POP M (Musik), ROCK M (Musik), EASY M (Musik), LIGHT M (Musik), CLASSICS, OTHER M Schwarz
(Musik), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, Schwarz: Masse
JAZZ, COUNTRY, NATION M (Musik), OLDIES, FOLK M (Musik), DOCUMENT Braun
Braun: Telefon-Stummschaltung
*2 Nur fr FM (UKW)-Quelle. Auxiliary-Eingabebuchse
2 Registrieren (pairen) Sie das Bluetooth-Gert mit KS-BTA100.
3 Whlen Sie [BT ADAPTER] fr [AUX] in [SRC SELECT]. ( 4)
4 Drcken Sie wiederholt zum Whlen von BT AUDIO.
5 Beginnen Sie die Verwendung des Bluetooth-Gerts.
Einzelheiten siehe Bedienungsanleitung des KS-BTA100.

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 6 21/9/2015 2:16:16 PM
Book Size: B6L (182 mm x 128 mm)
USB / iPod / ANDROID
Whlbare Quelle:
Starten Sie die Wiedergabe
KD-X230:
Die Quelle schaltet automatisch um, und die USB/ USB-IPOD/ ANDROID KD-X130
Wiedergabe startet. KD-X130:
USB/ ANDROID
USB-Eingangsterminal

USB
KD-X230: Zum direkten Whlen der USB/ USB-IPOD/ ANDROID-Quelle drcken Sie .

USB 2.0-Kabel*1 Zum Auf der Frontblende


(im Handel erhltlich) Vorspulen/Rckspulen*3 Halten Sie gedrckt.

iPod/iPhone Auswhlen einer Datei Drcken Sie .


Auswhlen eines Ordners*4 Drcken Sie .
Wiederholte Wiedergabe*5 Drcken Sie wiederholt.
(Zubehr beim TRACK RPT/ FOLDER RPT/ ALL RPT : MP3/WMA/WAV/FLAC-Datei
iPod/iPhone)*1 ONE RPT/ ALL RPT/ RPT OFF : iPod oder ANDROID
Zufallswiedergabe*5 Drcken Sie wiederholt.
FOLDERRND/ ALL RND/ RND OFF : MP3/WMA/WAV/FLAC-Datei
ANDROID*2 SONG RND/ ALL RND/ RND OFF : iPod oder ANDROID
*1 Lassen Sie bei Nichtgebrauch nicht das Kabel im Auto liegen.
*2 Wenn ein Android-Gert angeschlossen wird, wird Press [VIEW] to install JVC MUSIC PLAY APP angezeigt. Gehen Sie zur Installation der
Anwendung gem den Anweisungen vor. Sie knnen auch vor dem Verbinden die neueste Version der JVC MUSIC PLAY-Anwendung auf
Micro-USB 2.0-Kabel*1 Ihrem Android-Gert installieren. ( 11)
(im Handel erhltlich) *3 Bei ANDROID: Trifft nur zu, wenn [AUTO MODE] gewhlt ist. ( 8)
*4 Nur fr MP3/WMA/WAV/FLAC-Dateien. Dies funktioniert nicht bei iPod/ ANDROID.
*5 Bei iPod/ ANDROID: Trifft nur zu, wenn [HEAD MODE]/ [AUTO MODE] gewhlt ist. ( 8)

DEUTSCH 7

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 7 21/9/2015 2:16:16 PM
Book Size: B6L (182 mm x 128 mm)
USB / iPod / ANDROID

Whlen Sie den Steuermodus Auswhlen einer Datei aus einem Ordner/einer Liste
Whrend USB-IPOD als Quelle gewhlt ist, drcken Sie 1 Drcken Sie .
wiederholt. 2 Drehen Sie den Lautstrke-Regler zum Whlen eines Ordners/einer
HEAD MODE: Steuern Sie den iPod von dieser Einheit. Liste, und drcken Sie dann den Regler.
IPHONE MODE: Steuern Sie den iPod mit dem iPod selber. Sie knnen aber weiterhin 3 Drehen Sie den Lautstrke-Regler zum Whlen einer Datei, und
Wiedergabe/Pause oder Datei-berspringen von dieser Einheit steuern. drcken Sie dann den Regler.
Whrend ANDROID als Quelle gewhlt ist, drcken Sie Schnellsuche
wiederholt. Wenn Sie viele Dateien haben, knnen Sie diese schnell durchsuchen.
AUTO MODE: Steuern Sie das Android-Gert von dieser Einheit ber die im Android-Gert
installierte Anwendung JVC MUSIC PLAY. Drehen Sie den Lautstrke-Regler schnell, um die Liste schnell zu
AUDIO MODE: Steuern Sie das Android-Gert vom Android-Gert selber ber andere im durchsuchen.
Android-Gert installierte Media-Player-Anwendungen. Sie knnen aber Gilt nicht fr iPod.
weiterhin Wiedergabe/Pause oder Datei-berspringen von dieser Einheit
steuern. Alphabetsuche (gilt nur fr iPod):
Sie knnen eine Datei anhand des Anfangsbuchstabens suchen.
Drcken Sie oder drehen Sie den Lautstrke-Regler
Whlen Sie das Musiklaufwerk schnell, um das gewnschte Zeichen (A bis Z/ 0 bis 9/ OTHERS) zu
Drcken Sie wiederholt. whlen.
Whlen Sie OTHERS, wenn das erste Zeichen nicht A bis Z, 0 bis 9 ist.
Im folgenden Laufwerk gespeicherte Titel werden abgespielt.
Whlen Sie internen oder externen Speicher fr ein Smartphone (Massenspeicherklasse). Zum Zurckschalten zum vorherigen Einstellelement drcken Sie .
Gewhltes Laufwerk bei Gert mit mehreren Laufwerken. Zum Abbrechen halten Sie gedrckt.
Beim iPod nur gltig, wenn [HEADMODE] gewhlt ist.
Beim ANDROID nur gltig, wenn [AUTO MODE] gewhlt ist.
ndern der Wiedergabegeschwindigkeit des Hrbuchs
Beim Hren von iPod und wenn [HEADMODE] gewhlt ist....
1 Halten Sie gedrckt.
2 Drehen Sie den Lautstrke-Regler zum Whlen von [IPOD], und drcken Sie
dann den Regler.
3 Drcken Sie den Lautstrke-Regler zum Whlen von [AUDIOBOOKS].
4 Drehen Sie den Lautstrke-Regler zum Whlen eines Gegenstands, und
drcken Sie dann den Regler.
0.5SPEED / 1SPEED / 2SPEED: Whlen Sie die Wiedergabegeschwindigkeit der
Hrbuch-Tondatei in Ihrem iPod/iPhone.
(Standard: Je nach iPod/iPhone-Einstellung.)
5 Drcken Sie zum Beenden.
Zum Zurckschalten zum vorherigen Einstellelement drcken Sie .

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 8 21/9/2015 2:16:17 PM
Book Size: B6L (182 mm x 128 mm)
AUDIOEINSTELLUNGEN
Standard: XX
EQSETTING
EQPRESET Whlt einen Vorwahl-Equalizer, der fr das Musikgenre geeignet ist. (Whlen Sie [USER], um die
in [EASY EQ] vorgenommenen Einstellungen zu verwenden.)
FLAT(Standard) / HARD ROCK/ HIP HOP/ JAZZ/ POP/ R&B/ TALK/ USER/
VOCALBOOST/ BASSBOOST/ CLASSICAL/ DANCE

Whlen Sie einen Vorwahl-Equalizer EASYEQ Justieren Ihre eigenen Klangeinstellungen. Diese Einstellungen werden unter [USER] gespeichert.
SUB.W SP *1*2: 00bis+06 (Standard: 03
Drcken Sie wiederholt. SUB.W *1*3: 08bis+08 00
(oder)
Drcken Sie , und drehen Sie dann den Lautstrke-Regler BASSLVL: 06bis+06 00
innerhalb von 5 Sekunden. MIDLVL: 06bis+06 00
TRELVL: 06bis+06 00)
Vorwahl-Equalizer: FLAT (Standard), HARD ROCK, HIP HOP, JAZZ, POP, R&B, TALK, USER,
VOCAL BOOST, BASS BOOST, CLASSICAL, DANCE PRO EQ 1 BASS / MIDDLE / TREBLE:Whlen Sie einen Klangton.
2 Stellen Sie die Klangelemente des gewhlten Klangtons ein.
BASS Frequenz: 60/ 80/ 100/ 200HZ (Standard: 80HZ
Speichern Ihre eigenen Klangeinstellungen Pegel: 06 bis +06 00
1 Halten Sie gedrckt, um auf EASY EQ-Suche zu schalten. Q: Q1.0/ Q1.25/ Q1.5/ Q2.0 Q1.0)
2 Drehen Sie den Lautstrke-Regler zum Whlen eines Gegenstands, und MIDDLE Frequenz: 0.5/ 1.0/ 1.5/ 2.5KHZ (Standard: 1.0KHZ
drcken Sie dann den Regler. Pegel: 06 bis +06 00
Siehe [EASYEQ] bezglich der Einstellung, und das Ergebnis wird unter [USER] Q: Q0.75/ Q1.0/ Q1.25 Q1.25)
gespeichert.
TREBLE Frequenz: 10.0/ 12.5/ 15.0/ 17.5KHZ (Standard: 10.0KHZ
Zum Zurckschalten zum vorherigen Einstellelement drcken Sie . Pegel: 06 bis +06 00
Zum Beenden drcken Sie .
Q: QFIX QFIX)
AUDIO
Andere Einstellungen
BASS BOOST +01+05(+01): Whlt Ihren bevorzugten Bass-Boost-Pegel.; OFF:Hebt auf.
1 Halten Sie gedrckt.
2 Drehen Sie den Lautstrke-Regler, um einen Gegenstand zu treffen LOUD 01/02:Verstrkt niedrige oder hohe Frequenzen, um eine gute Klangwirkung auch bei niedriger
(siehe folgende Tabelle), und drcken Sie dann den Regler. Lautstrke zu erhalten.; OFF:Hebt auf.
3 Wiederholen Sie Schritt 2, bis der gewnschte Gegenstand gewhlt/ *1 Wird nur angezeigt, wenn [SUB.W] auf [ON] gestellt ist. ( 10)
aktiviert ist, oder folgen Sie den Anweisungen auf dem gewhlten *2 Wird nur angezeigt, wenn [SPK/PREOUT] auf [SUB.W/SUB.W] gestellt ist. ( 10)
Gegenstand. *3 Wird nur angezeigt, wenn [SPK/PREOUT] auf [REAR/SUB.W] oder [SUB.W/SUB.W] gestellt
4 Drcken Sie zum Beenden. ist. ( 10)
Zum Zurckschalten zum vorherigen Einstellelement drcken Sie .

DEUTSCH 9

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 9 21/9/2015 2:16:17 PM
Book Size: B6L (182 mm x 128 mm)
AUDIOEINSTELLUNGEN
*4 Wird nur angezeigt, wenn [SUB.W] auf [ON] gestellt ist.
SUB.W LEVEL *4 SPK-OUT *5 00bis+06(+03):Stellt den Ausgangspegel des ber
*5 Wird nur angezeigt, wenn [SPK/PREOUT] auf [SUB.W/SUB.W] gestellt ist.
Lautsprecherleitung angeschlossenen Subwoofers ein. ( 15)
*6 Wird nur angezeigt, wenn [SPK/PREOUT] auf [REAR/SUB.W] oder [SUB.W/SUB.W] gestellt
PRE-OUT *6 08bis+08(00):Stellt den Ausgangspegel des an die Line-Out- ist.
Anschlsse (REAR/SW) ber einen externen Verstrker angeschlossenen *7 Die Einstellung kann nicht den Subwoofer-Ausgang beeinflussen.
Subwoofers ein. ( 15) *8 Arbeitet nicht, wenn [BTADAPTER] fr [AUX] in [SRCSELECT] gewhlt ist. ( 4)
SUB.W *6 ON/OFF: Schaltet den Subwoofer-Ausgang ein oder aus.
SUB.WLPF *4 THROUGH:Alle Signale werden zum Subwoofer gesendet. ; LOW 55HZ/ Lautsprecher-Ausgangseinstellungen
MID 85HZ/ HIGH120HZ:Audiosignale mit niedrigeren Frequenzen als 55Hz/ 85Hz/ Whlen Sie die Ausgangseinstellung fr die Lautsprecher [SPK/PRE OUT], basierend auf
120Hz werden zum Subwoofer geleitet. der Art des Lautsprecheranschlusses.
SUB.WPHASE *4 REVERSE(180)/ NORMAL(0):Whlt die Phase des Subwoofer-Ausgangs so, dass
sie dem Lautsprecher-Ausgang fr optimale Leistung entspricht. (Nur whlbar, wenn eine Anschluss ber Line-Out-Buchsen
andere Einstellung als [THROUGH] fr [SUB.WLPF] gewhlt ist.) Fr Verbindungen ber einen externen Verstrker. ( 15)
FADER R06F06(00):Stellen Sie die Ausgangsbalance zwischen vorderen und hinteren Einstellung auf Audiosignal ber Line-Out-Anschluss
Lautsprechern ein.
[SPK/PRE OUT] REAR/SW
BALANCE *7 L06R06(00):Stellen Sie die Ausgangsbalance zwischen linken und rechten
Lautsprechern ein. REAR/REAR Hinterer Lautsprecherausgang

VOLADJUST 15+06(00):Nehmen Sie die Vorwahl des anfnglichen Lautstrkepegels fr jede REAR/SUB.W Subwoofer-Ausgang
Quelle (in Bezug auf den FM (UKW)-Lautstrkepegel) vor. Vor der Einstellung whlen Sie eine SUB.W/SUB.W Subwoofer-Ausgang
anzupassende Quelle aus. (VOLADJFIX erscheint im Display, wenn FM (UKW) gewhlt ist.)
AMPGAIN LOWPOWER:Beschrnkt den maximalen Lautstrkepegel auf 25. (Whlen Sie dies, Anschluss ber Lautsprecherkabel
wenn die Maximalleistung jedes Lautsprechers weniger als 50 W betrgt, um Schden an den Fr Verbindungen ohne externen Verstrker Mit diesen Einstellungen knnen Sie aber
Lautsprechern zu verhindern).; HIGHPOWER:Der maximale Lautstrkepegel ist 35. auch den Subwoofer-Ausgang genieen. ( 15)
D.T.EXP ON:Erzeugt realistischen Klang, indem die Hochfrequenzkomponenten kompensiert und Audiosignal ber hintere Lautsprecherleitung
(Digital Track die Anstiegszeit der Wellenform, die bei der Audiodaten-Kompression verloren gehen, Einstellung auf
Expander) wiederhergestellt werden.; OFF:Hebt auf. [SPK/PRE OUT] L (links) R (rechts)
TELMUTING *8 ON:Schaltet den Ton bei Verwendung des Mobiltelefons stumm (nicht ber KS-BTA100 REAR/REAR Hinterer Lautsprecherausgang Hinterer Lautsprecherausgang
angeschlossen).; OFF:Hebt auf. REAR/SUB.W Hinterer Lautsprecherausgang Hinterer Lautsprecherausgang
SPK/PREOUT Whlen Sie je nach der Art des Lautsprecheranschlusses die geeignete Einstellung, um den SUB.W/SUB.W Subwoofer-Ausgang (Stummschaltung)
gewnschten Ausgang zu erhalten. ( Lautsprecher-Ausgangseinstellungen)
Wenn [SUB.W/SUB.W] gewhlt ist:
[HIGH120HZ] ist in [SUB.WLPF] gewhlt, und [THROUGH] steht nicht zur Verfgung.
[R01] ist in [FADER] gewhlt, und der Wahlbereich ist [R06] bis [00].

10

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 10 21/9/2015 2:16:17 PM
Book Size: B6L (182 mm x 128 mm)
DISPLAY-EINSTELLUNGEN ZUR BEZUGNAHME
Wartung
Reinigung des Gerts
Wischen Sie die Frontblende mit einem trockenen Silikonlappen oder weichen Lappen sauber.

Reinigung des Steckverbinders


Die Frontblende abnehmen und den Anschluss sanft mit einem
1 Halten Sie gedrckt. Wattetupfer oder Lappen reinigen, wobei darauf geachtet
2 Drehen Sie den Lautstrke-Regler, um einen Gegenstand zu treffen werden muss, die Anschlusskontakte nicht zu beschdigen.
(siehe folgende Tabelle), und drcken Sie dann den Regler. Anschluss (an der Rckseite der
3 Wiederholen Sie Schritt 2, bis der gewnschte Gegenstand gewhlt/ Weitere Informationen Frontblende)
aktiviert ist, oder folgen Sie den Anweisungen auf dem gewhlten
Gegenstand. Besuchen Sie die folgende Website <http://www.jvc.net/cs/car/> fr:
4 Drcken Sie zum Beenden. Neuste Firmware-Aktualisierungen und eine Liste der neuesten kompatiblen Artikel
Android-Anwendung JVC MUSIC PLAY
Zum Zurckschalten zum vorherigen Einstellelement drcken Sie . Jegliche neuesten Informationen
Standard: XX
DISPLAY Abspielbare Dateien
Wiederzugebende Audiodateien: MP3 (.mp3), WMA (.wma), WAV(.wav), FLAC (.flac)
DIMMER Blenden Sie die Display- und Tastenbeleuchtung ab. Mgliche Dateisysteme auf USB-Gerten: FAT12, FAT16, FAT32
OFF:Die Abblendung ist ausgeschaltet. Auch wenn Audiodateien den oben aufgefhrten Standards entsprechen, kann das Abspielen unter Umstnden auf
ON:Die Abblendung ist eingeschaltet. Die Helligkeit wechselt auf [NIGHT]-Einstellung um. Grund von Typ oder Zustand der Medien bzw. Gerte nicht mglich sein.
( [BRIGHTNESS])
DIMMER TIME:Stellen Sie die Anfangs- und Endzeit fr die Abblendfunktion ein. Wissenswertes ber USB-Gerte
1 Drehen Sie den Lautstrke-Regler zum Einstellen der Einschaltzeit [ON], und drcken Sie Diese Einheit kann MP3/WMA/WAV/FLAC-Dateien abspielen, die auf einem USB-Massenspeichergert gespeichert
dann den Regler. sind.
2 Drehen Sie den Lautstrke-Regler zum Einstellen der Einschaltzeit [OFF], und drcken Sie Sie knnen ein USB-Gert nicht ber einen USB-Hub anschlieen.
dann den Regler. Der Anschluss eines Kabels mit einer Gesamtlnge von mehr als 5 m kann eine fehlerhafte Wiedergabe verursachen.
(Standard: [ON]: 18:00 oder 6:00 PM Maximalzahl von Zeichen fr:
[OFF]: 6:00 oder 6:00 AM) - Ordnernamen: 64 Zeichen
AUTO:Die Abblendung schaltet automatisch ein und aus, wenn Sie die Autoscheinwerfer ein- - Dateinamen: 64 Zeichen
oder ausschalten. *1 - MP3-Tag: 64 Zeichen
- WMA-Tag: 64 Zeichen
BRIGHTNESS Stellt die Tasten-, Display- und USB-Eingangsbuchsenhelligkeit fr Tag und Nacht separat ein. - WAV-Tag: 64 Zeichen
1 DAY / NIGHT:Whlen Sie Tag oder Nacht. - FLAC-Tag: 64 Zeichen
2 Whlen Sie eine Zone. Dieses Gert kann insgesamt 15 000 Dateien, 500 Ordner (999 Dateien pro Ordner einschlielich Ordner ohne nicht-
3 Stellen Sie den Helligkeitspegel ein (00 bis 31). (Standard: DAY:31; NIGHT:15) untersttzte Dateien) und 8 Hierarchien erkennen.
SCROLL *2 ONCE:Scrollt die Display-Information einmal.; AUTO:Wiederholt das Scrollen in 5-Sekunden- Diese Einheit kann nicht ein USB-Gert mit einer anderen Bewertung als 5 V und mehr als 1 A erkennen.
Intervallen.; OFF:Hebt auf.
*1 Die Steuerleitungsverbindung fr Beleuchtung ist erforderlich. ( 15)
*2 Manche Zeichen oder Symbole werden nicht richtig angezeigt (oder werden ausgeblendet).
DEUTSCH 11

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 11 21/9/2015 2:16:18 PM
Book Size: B6L (182 mm x 128 mm)
ZUR BEZUGNAHME
Wissenswertes ber iPod/iPhone ndern der Display-Information
Made for Jedesmal, wenn Sie drcken, wechselt die Anzeige-Information.
- iPod touch (2nd, 3rd, 4th und 5th generation) Wenn die Information nicht verfgbar oder nicht aufgezeichnet ist, erscheint NO TEXT, NO NAME oder andere
- iPod classic Information (z.B. Sendername).
- iPod nano (3rd, 4th, 5th, 6th und 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus FM oder AM Frequenz Tag/Uhrzeit
Es ist nicht mglich, Videodateien im Men Videos in [HEAD MODE] zu durchsuchen. (Nur fr Radio Data System-FM (UKW)-Sender)
Die Song-Reihenfolge, die im gewhlten Men dieser Einheit erscheint, kann sich vom iPod/iPhone unterscheiden. Sendername (PS) Frequenz Programmtyp (PTY) Radiotext+ Tag/Uhrzeit
Je nach der Version des Betriebssystems des iPod/iPhone sind einige Funktionen mglicherweise nicht verfgbar. (zurck zum Anfang)
Wissenswertes ber Android-Gerte USB (Fr MP3/WMA/WAV/FLAC-Datei)
Diese Einheit untersttzt Android OS 4.1 und hher. Spielzeit Tag/Uhrzeit Albumtitel/Interpret Tracktitel Ordner-/Dateiname
Manche Android-Gerte (mit OS 4.1 und hher) untersttzen mglicherweise Android Open Accessory (AOA) 2.0 (zurck zum Anfang)
nicht vollstndig.
Wenn das Android-Gert sowohl Massenspeicherklasse-Gert als auch AOA 2.0 untersttzt, hat diese Einheit immer USB-IPOD Spielzeit Tag/Uhrzeit Albumtitel/Interpret Tracktitel (zurck zum Anfang)
Wiedergabe ber AOA 2.0 als Vorrang. oder ANDROID
AUX AUX Tag/Uhrzeit
Verfgbare kyrillische Buchstaben BT AUDIO BT AUDIO Tag/Uhrzeit
Verfgbares Zeichen
Displayanzeigen

12

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 12 21/9/2015 2:16:18 PM
Book Size: B6L (182 mm x 128 mm)
FEHLERSUCHE
Symptom Abhilfe Symptom Abhilfe
Es wird kein Ton gehrt. Die Lautstrke auf den optimalen Pegel einstellen. Bei Wiedergabe wird kein Verbinden Sie das Android-Gert neu.
Prfen Sie die Kabel und Verbindungen. Ton gehrt. Whrend der [AUDIO MODE] eingestellt ist, starten Sie eine
Ton wird nur vom Android- Media Player Anwendung auf dem Android-Gert und starten Sie die
MISWIRING CHECK WIRING THEN Schalten Sie die Stromversorgung aus, und prfen Sie, ob die
Allgemeines

PWR ON erscheint. Klemmen der Lautsprecherdrhte richtig isoliert sind. Schalten Sie die Gert ausgegeben. Wiedergabe.
Stromversorgung wieder ein. Whrend der [AUDIO MODE] eingestellt ist, starten Sie die aktuelle
Media Player Anwendung erneut oder verwenden Sie eine andere
PROTECTING SEND SERVICE Reichen Sie die Einheit beim nchsten Kundendienstzentrum ein. Media Player Anwendung.
erscheint. Starten Sie das Android-Gert neu.
Quelle kann nicht gewhlt werden. Prfen Sie die Einstellung [SRCSELECT]. ( 4) Wenn dadurch das Problem nicht gelst wird, kann das angeschlossene
Android-Gert nicht das Audiosignal zur Einheit leiten. ( 12)
Der Radioempfang ist schlecht. Schlieen Sie das Antennenkabel fest an.
Radio

Statikrauschen beim Radiohren. Bei [AUTO MODE] ist Stellen Sie sicher, dass JVC MUSIC PLAY APP im Android-Gert installiert
Wiedergabe unmglich. ist. ( 7)
Die Wiedergabereihenfolge ist nicht Die Wiedergabereihenfolge wird durch den Dateinamen. Schlieen Sie das Android-Gert erneut an und whlen Sie den

ANDROID
wie gewnscht. geeigneten Steuermodus. ( 8)
Verflossene Spielzeit ist nicht richtig. Dies hngt von dem vorherigen Aufnahmevorgang ab. Wenn das Problem dadurch nicht gelst wird, untersttzt das
verbundene Android-Gert nicht [AUTO MODE]. ( 12)
"NOT SUPPORT" erscheint, und Prfen Sie, ob die Datei ein abspielbares Format hat. ( 11)
Dateien werden bersprungen. NO DEVICE oder READING Schalten Sie die Entwickler-Optionen am Android-Gert aus.
blinkt weiter. Verbinden Sie das Android-Gert neu.
READING blinkt weiter. Verwenden Sie nicht zu viele Hierarchie-Ebenen und Ordner. Wenn das Problem dadurch nicht gelst wird, untersttzt das
Bringen Sie das USB Gert wieder an. verbundene Android-Gert nicht [AUTO MODE]. ( 12)
USB / iPod

CANNOT PLAY blinkt und/oder das Prfen Sie, ob das angeschlossene Gert kompatibel mit diesem Gert ist, Die Wiedergabe ist Schalten Sie den Stromsparmodus am Android-Gert aus.
angeschlossene Gert kann nicht und stellen Sie sicher, dass die Dateien die untersttzten Formate haben. unterbrochen oder es treten
erkannt werden. ( 11) Aussetzer im Ton auf.
Bringen Sie das Gert wieder an.
CANNOT PLAY Achten Sie darauf, dass das Android-Gert abspielbare Audiodateien
Der iPod/iPhone schaltet nicht ein Prfen Sie die Verbindung zwischen diesem Gert und dem iPod/iPhone. enthlt.
oder funktioniert nicht. Nehmen Sie das iPod/iPhone ab und setzen es mit Hard Reset zurck. Verbinden Sie das Android-Gert neu.
Richtige Zeichen werden nicht Dieses Gert kann nur Grobuchstaben, Zahlen und eine begrenzte Starten Sie das Android-Gert neu.
angezeigt. Anzahl von Symbolen anzeigen.
Je nach der Anzeigesprache, die Sie gewhlt haben ( 4), knnen
bestimmte Buchstaben mglicherweise nicht richtig angezeigt werden. Wenn Sie weiterhin Probleme haben, fhren Sie einen Reset aus. ( 3)

DEUTSCH 13

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 13 21/9/2015 2:16:19 PM
Book Size: B6L (182 mm x 128 mm)
EINBAU / ANSCHLUSS Warnung
Das Gert kann nur bei 12 V DC-Versorgung mit negativer Masse eingebaut werden.
Einbau der Einheit (Einbau im Armaturenbrett)
Trennen Sie den negativen Batterieanschluss vor der Verkabelung und Befestigung ab.
Schlieen Sie nicht das Batteriekabel (gelb) das Zndkabel (rot) an der Fahrzeugkarosserie
oder dem Massekabel (schwarz) an, um einen Kurzschluss zu vermeiden.
Isolieren Sie nicht angeschlossene Kabel mit Vinylband, um einen Kurzschluss zu Fhren Sie die erforderliche
vermeiden. Verkabelung aus. ( 15)
Sicherstellen, da das Gert nach dem Einbau a Chassis des Fahrzeugs geerdet wird.
Vorsicht
berlassen Sie aus Sicherheitsgrnden die Arbeiten zur Montage und Verkabelung
ausgewiesenem Fachpersonal. Lassen Sie sich vom Autoradiohndler beraten. Haken auf der Oberseite
Montieren Sie dieses Gert in der Konsole Ihres Fahrzeugs. Keine Metallteile dieses Gerts
bei und kurz nach der Verwendung des Gerts berhren. Metallteile wie der Khlkrper und Armaturenbrett Ihres
das Gehuse werden hei. Richten Sie den Frontrahmen vor dem Autos
Verbinden Sie nicht die -Drhte von Lautsprechern mit der Karosserie, dem Massekabel Anbringen aus, wie in der Abbildung
(schwarz) oder schlieen sie parallel an. gezeigt.
Schlieen Sie Lautsprecher mit einer Maximalleistung von mehr als 50 W an. Wenn
die Maximalleistung der Lautsprecher unter 50 W ist, ndern Sie die Einstellung von
[AMPGAIN], um Beschdigung der Lautsprecher zu vermeiden. ( 10) Die geeigneten Zapfen biegen, um die
Montieren Sie das Gert mit einem Winkel von weniger als 30. Manschette sicher festzuhalten.
Wenn Ihr Fahrzeugkabelbaum nicht die Zndklemme hat, verbinden Sie das Zndkabel
(rot) mit der Klemme am Sicherungskasten des Fahrzeugs, die 12 V DC-Versorgung bietet
und durch den Zndschlssel ein- und ausgeschaltet wird. Beim Einbau des Gerts ohne Einbauhalterung
Halten Sie alle Kabel von hitzeableitenden Metallteilen fern. 1 Nehmen Sie die Einbauhalterung und den
berprfen Sie nach der Montage des Gerts, ob die Bremslichter, Blinker, Scheibenwischer Frontrahmen vom Gert ab.
usw. ordnungsgem funktionieren. 2 Richten Sie die ffnungen am Gert (an beiden
Wenn die Sicherung durchbrennt, berprfen Sie zuerst, dass die Drhte nicht die Seiten) mit der Befestigungskonsole am Fahrzeug
Karosserie berhren, und ersetzen Sie dann die durchgebrannte Sicherung durch eine neue aus und sichern Sie das Gert mit Schrauben (im
Sicherung mit der gleichen Nenngre. Handel erhltlich).
Verwenden Sie nur die vorgeschriebenen Schrauben. Durch Verwendung falscher
Grundlegendes Verfahren Schrauben kann das Gert beschdigt werden.
1 Ziehen Sie den Schlssel aus dem Zndschloss, und
trennen Sie dann den -Pol der Autobatterie ab.
2 Schlieen Sie die Kabel richtig an. Entfernen der Einheit
Siehe Verdrahtungsanschluss. ( 15)
3 Bauen Sie das Autoradio in Ihrem Fahrzeug ein.
Siehe Einbau der Einheit (Einbau im Armaturenbrett).
4 Schlieen Sie die -Klemme der Autobatterie an.
5 Setzen Sie das Gert zurck. ( 3)

14

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 14 21/9/2015 2:16:19 PM
Book Size: B6L (182 mm x 128 mm)
Verdrahtungsanschluss
Bei Anschluss an einen externen Verstrker schlieen
Hinterer/Subwoofer-Ausgang Sie dessen Massedraht an der Autokarosserie an, um
Beschdigung des Gerts zu vermeiden.

Teileliste fr den
Sicherung (10 A) Antennenanschluss Einbau
(A) Frontblende

Anschluss des ISO-Anschlusses an manche


Falls kein Anschluss durchgefhrt wird, lassen Sie den Draht
VW/Audi oder Opel (Vauxhall) Automobile Gelb (Batteriekabel) bitte nicht aus der Lasche hervorstehen.
Sie mssen mglicherweise die Verkabelung des (B) Frontrahmen
mitgelieferten Kabelbaums modifizieren, wie unten gezeigt. Hellblau/Gelb Zum Lenkrad-
Rot (Zndkabel) (Lekungs- STEERING
WHEEL
Fernbedienungsadapter
Fernbedienungskabel) REMOTE

A7 (Rot) Zndkabel (Rot) Stift Farbe und Funktion


Fahrzeug A2 Braun : Mobiltelefonsystem (C) Einbauhalterung
Gert
A4 Gelb : Batterie
A4 (Gelb) Batteriekabel Rot (A7) A5 Blau/Wei : Stromsteuerung
(Gelb)
A6 Orangefarben/Wei : Auto-Lichtreglerschalter
Standardverkabelung A7 Rot : Zndung (ACC)
Gelb (A4)
A8 Schwarz : Erdungsanschluss (Masse) (D) Kabelbaum
B1 Lila ]
: Hinterer Lautsprecher (rechts)
* Sie knnen auch einen Subwoofer-Lautsprecher direkt ohne einen externen B2 Lila/Schwarz [
Subwoofer-Verstrker anschlieen. Fr Einstellung, 10. B3 Grau ]
: Vorderer Lautsprecher (rechts)
B4 Grau/Schwarz [
Wenn Ihr Fahrzeug KEINEN ISO-Anschluss hat B5 Wei ]
Wir empfehlen, die Einheit mit einem im Handel erhltlichen, fr Ihr Fahrzeug : Vorderer Lautsprecher (links)
ausgelegten Kabelbaum zu installieren und diese Arbeit zur Ihrer eigenen Sicherheit B6 Wei/Schwarz [ (E) Ausziehschlssel
von qualifizierten Fachleuten ausfhren zu lassen. Lassen Sie sich von Ihrem B7 Grn ]
Autoradiohndler beraten. ISO-Anschlsse : Hinterer Lautsprecher (links) *
B8 Grn/Schwarz [

DEUTSCH 15

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 15 21/9/2015 2:16:20 PM
Book Size: B6L (182 mm x 128 mm)
TECHNISCHE DATEN
FM Frequenzbereich 87,5MHz 108,0MHz (50-kHz-Raster) Frequenzgang (3 dB) 20Hz 20kHz

Auxiliary
Empfindlichkeit (Rauschabstand = 26dB) 0,71 V/75 Maximaler Spannungseingang 1 000mV
Empfindlichkeitsschwelle (DIN S/N = 46 dB) 2,0 V/75 Eingangsimpedanz 30k
Frequenzgang (3 dB) 30Hz 15kHz Maximale Ausgangsleistung 50W4 oder
50W 2 + 50W 1 (Subwoofer = 4 )
Tuner

Signal-Rauschabstand (MONO) 64 dB
Kanaltrennung (1 kHz) 40 dB Volle Bandbreitenleistung 22W4

Audio
(bei weniger als 1% Klirrfaktor)
MW Frequenzbereich 531 kHz 1 611 kHz (9-kHz-Raster)
Lautsprecherimpedanz 48
Empfindlichkeit (Rauschabstand = 20dB) 28,2V
Vorverstrkerpegel / Last (USB) 2 500 mV/10k
LW Frequenzbereich 153kHz 279kHz (9-kHz-Raster)
Vorverstrkungsimpedanz 600
Empfindlichkeit (Rauschabstand = 20dB) 50V
Betriebsspannung 14,4V
USB Standard USB1.1, USB2.0 (Hchstgeschwindigkeit) (10,5 V 16 V zulssig)

Allgemeines
Kompatible Gerte Massenspeichergert Maximale Stromaufnahme 10A
Dateisystem FAT12/16/32 Betriebstemperaturbereich 10C +60C
Maximaler Versorgungsstrom DC 5 V 1A Einbaumae (B H T) 182mm53mm107mm
D/A-Wandler 24 Bit Gewicht 0,6kg
Frequenzgang (1 dB) 20Hz 20kHz
nderungen ohne Vorankndigung bleiben vorbehalten.
USB

Signal-Rauschabstand (1 kHz) 105 dB


Dynamikbereich 88 dB
Kanaltrennung 90 dB
MP3-Decodierung Untersttzt MPEG-1/2 Audio Layer-3
WMA-Decodierung Untersttzt Windows Media Audio
WAV-Decodierung RIFF-Wellenform-Audioformat (nur Linear PCM)
FLAC-Decodierung FLAC-Dateien

16

Data Size: B6L (182 mm x 128 mm)


JS_JVC_KD_X230_X130_E_GE.indd 16 21/9/2015 2:16:20 PM
Book Size: B6L (182 mm x 128 mm)
JS_JVC_KD_X230_X130_E_GE.indd 17 21/9/2015 2:16:20 PM
Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Made for iPod, and Made for iPhone mean that an electronic accessory has been
designed to connect specifically to iPod, or iPhone, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and regulatory standards. Please
note that the use of this accessory with iPod or iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Lightning is a trademark of Apple Inc.
Android is trademark of Google Inc.

libFLAC
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2007,2008,2009 Josh Coalson
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
- Neither the name of the Xiph.org Foundation nor the names of its contributors may be
used to endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND ONTRIBUTORS AS IS
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

2015 JVC KENWOOD Corporation 1015DTSMDTJEIN

JS_JVC_KD_X230_X130_E_C00.indd iii Data Size: B6L (182 mm x 128 mm) 14/8/2015 11:59:37 AM
Book Size: B6L (182 mm x 128 mm)

You might also like