Professional Documents
Culture Documents
LION'S TR
ACS
MIDI
Flash Memory:128Kb Flash Ram
Megafloppy 4.00
3
2
1234
1234
Internal interface hard disk IDE 2,5 1234
1 1234
Interface Floppy Drive IN - OUT 1234
1234
Interface Standard SCSI 25 pin. 1234
1234
Interface MIDI IN - OUT 1234
Serial Interface TX -RX
1234
1234
Power Supply: +5V 800mA with hard disk 2,5 IDE
MIDI
123
SW5.00a 3
MF 4.00 SW5.00
2 123
123
MF 4.00
123
U7 U6
1
123
Actel RAM
123
FLASH
123
123
123
123
4
KIT CAVO MIDI OUT:
1 123
3
2
1
4=BLU wire, sold to connector MIDI OUT Pin5.
5=Filo Giallo,sold to connector MIDI OUT Pin4.
MIDI OUT
MEGAFLOPPY 4.00 Standard 3.5 Kit is shipped with the follow parts:
In the all Kit Megafloppy, is available a special flat cable 44 pins 35 Cm
long. Use this cable for connecting the Megafloppy mainboard to the A) Nr. 1 Hard Disk IDE 2,5 with the metal support and biadesive tape 3M
hard disk. B) Nr. 1 Flat cable 44 pin for the Hard Disk 2,5 IDE, 35 Cm long
Normally the cable is already connected from Lions Tracs in to hard disk. C) Nr. 1 minibag containg 8 srews and 8 add spacing
D) Nr. 1 Montage Manual
E) Nr. 1 Owners Manual
ATTENTION: External Box Hard Disk IDE 2,5
Connect the cable whit the
pin 1 RED in to hard disk 2.5 123456789012345 12
Pin 1
pin 1.
Normaly remain 4 free pins in
123456789012345
44 pin conn.
12
the right side.
See the picture for reference. Pin 1
12345678901234567890123456
12345678901234567890123456
In the Megafloppy 12345678901234567890123456
12345678901234567890123456
connect the cable whit the cavo 35 cm 12345678901234567890123456
pin 1 in to Megafloppy HD 44pin 12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
connector IDE hard disk pin 1.
12345678901234567890123456 MEGAFLO
12345678901234567890123456 PPY
12345678901234567890123456
12345678901234567890123456
Pin 1 12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
LION'S TR
ACS
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
Pin 1
A
44 Pin IDE Cable
ATTENTION:
Dont never mount the
hard disk above the
MICRO spekers!
2 MIDI
1
2
PROCES.
3 H8/3003
4
5
SW5.00a
MF 4.00 SW5.00
B
MF 4.00
U7 U6
Actel RAM
FLASH
4
3
2
1
1
Before close all the parts, verifing if the hard disk cable are complectely
inserted in the hard disk connector and in the Megafloppy connector.
C
If the hard disk cable is not good inserted, is possible that Megafloppy read
wrong data or ask for a new hard disk format!
Before closing the instrument, make sure: that no cables are blocking its ATTENTION: Device SCSI # 6 Zip +
closure and that the installation procedure described above has been carried Before turn on the Keyboard,
check that the SCSI chain is Terminator
out perfectly.
closed whit the SCSI
Terminator. Device SCSI # 5 Changer
Attention:
The space which holds the streep point of the logic card is under the Device SCSI # 3 HD
connector of the hard disk and the floppy driver. The connector of the keel
block must in fact be positioned inside this space.
In some cases the connector of the keel block of the floppy driver may Device SCSI # 2 HD
overturn and, should that happen, check that the Megafloppy at start up
lights Error
The feeding connector is made up of 4 pins. The mass is situated in the 2 Device SCSI # 1 HD
central pins, while PIN+5 is the first turned towards the hard disk connector.
The polarity recognition lead of + 5V. is usually red. Before closing the
Device IDE Master HD 2.5 44 Pin IDE Cable
instrument, check again that the connectors have been correctly mounted
and that they do not slip out their fittings.
MEGAFLO
PPY
LION'S TR
ACS
NOTE: The single CD-ROM Drive, must set at SCSI number #4 and work with
2048 Kb sector only!
+ Terminator
M 2,5 X 5-6
ATTENTION:
Before turn on the Keyboard,
check that the SCSI chain is
MEGAFLO
closed whit the SCSI PPY
Terminator.
LION'S TR M 2,5 X 5-6
ACS
M3X4
MEGAFL
OPPY
LION'S TRA
CS
Kit supplies 4pcs M2.5 screws each 5-6mm.long
Kit supplies 4pcs M3 screws each 4mm. long
OPTIONAL:
Fou use the external SCSI CD-ROM or hard disk, you need the
internal Megafloppy SCSI cable 25 to DB 25 standard SCSI
connector.
Operation: remove the original floppy Drive from the Keyboard. Actel MIDI FPGA KEY release 5.00 Upgrade
U7
Disconnect the 34 pin Flat cable and the Power Supply connector. MF 4.00
Reconect the same two cables in to Megafloppy connectors and connect SW5.00a
the IDE 2.5 Hard Disk.
Internal MIDI cable Megafloppy
included with the MIDI Key 5.0
4
3
2
1
1
NOTE: Cables SCSI standard 25 pin to
Connect the two flat cable in to Megafloppy and turn on the keyboard. If 50 pin Centronics.
Megafloppy displayed Er. InP. error Input: reverse the flat cable FLOPPY
IN of 180 and rebot again.
In the Megafloppy standard model, is impossible that the display write Er.
OUP. error output, because it incorporate one TEAC Slim floppy Drive.In this New aux power supply Kit 5V. 3A.
way, Megafloppy dont must displayed any type of errors message, if yes, is for the keyboards that dont have
impossible to comunicate whit the Keyboard or whit the Floppy Disk Drive. sufficently power supply.
L8xD5XH4.5 Cm
Original Keyboard
floppy cable
Original Floppy Disk Drive 12345678901234
12345678901234
1234567890 12345678901234
12345678901234
Power +5v. 1234567890 12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234 Duplicate Power
12345678901234
12345678901234 Supply cable
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
Original
Power Cord
To original
Floppy Drive
SEL. MICRO
2 MIDI
1
2
PROCES.
Remote display 3 H8/3003
4
5
123456
123456
123456 SW5.00a
123456
123456 MF 4.00 SW5.00
123456
123456
MF 4.00
U7
123456
U6
4
3
2
1
1
Find a place for the Remote Display and drill the cover of the Keyboard for
fixing the Remote. When the Remote is fixed, fasten the included Lexan cover
Remote.
Kit MegafloppySTD 3.5 with Solton Keyboards
NOTE: Connect the two flat cable in to Megafloppy and turn on the keyboard. In Configuration System CS Solton must set to:
If Megafloppy displayed Er. InP. error Input: reverse the flat cable FLOPPY CS dCH + CS 1.44 + CS std + CS 4.00+ CS nor+ CS nYS
IN of 180 and rebot again. If at rebot displayed Er. OUP. error output,
reverse the flat cable FLOPPY OUT and rebot again. Kit Megafloppy PCB with Solton Keyboards
Megafloppy dont must displayed any errors message, if yes, is impossible to In Configuration System CS Solton must set to:
comunicate whit the Keyboard or whit the original Floppy Disk Drive. CS rdY + CS 1.44 + CS std + CS 4.00+ CS SOL+ CS nYS
G
If you have any problems, please dont esitate to ask at Lions Tracs Italy. Write and
send one fax or E-Mail direct to Lions Tracs.
Our company need now any kings of errors or problem, to correct the software
and resend a new release direct to you. H
All new release are then available online in Internet at www.megafloppy.com.
OA
RDM
EG
H) Nr. 1 Montage Manual
B ISK
MA
IN
-D
HA
RD I ) Nr. 1 Owners Manual
MEGAFLO
PPY
The Roland G-600 dont use the rear holding metal and is possible connect LION'S TRAC
S
the original flat 34 pin cable from G-600 direct to the Megafloppy 34 pin
connector INPUT.
A
E
G-600 F
Y
PP
LO
AF
EG
DM
AR K
BO IS
MAIN -D
RD
HA
If the Kit is shipped from Lions Tracs, the Megafloppy is totally configured
and the hard disk is preloaded of demo files.
G
Megafloppy
Driver FD PANASONIC
1234567890 12345678901234
12345678901234
XPGS
Power +5v. 1234567890 12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
DRIVE Roland G-800 12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
12345678901234
Pin 1 12345678901234
12345678901234
12345678901234 Kit G-800/600 Power
12345678901234
12345678901234
Roland G-600 Power supply 12345678901234
12345678901234
12345678901234
Supply cable
12345678901234
12345678901234
12345678901234
6 Megafloppy
MICRO
2 MIDI
Roland G-600 DRIVE 1
2
3
4
PROCES.
H8/3003
5
SW5.00a
MF 4.00 SW5.00