You are on page 1of 6

Data sheet

Customer item no.:1


Communication dated: 19/04/2017 Number: ES 4677763
Doc. no.: PT. WELTES Item no.: 100
Quantity: 1 Date: 19/04/2017
Page: 1 / 6

Multitec C 100/ 6-7.1 20.181 Version no.: 1

Operating data
Requested flow rate 120.00 m/h Actual flow rate 120.00 m/h
Operating data determined for maximum inlet pressure Actual developed head 378.48 m
Requested developed head 378.47 m Efficiency 76.2 %
Pumped medium Water, boiler feed water Power absorbed 153.11 kW
Fully desalinated water Pump speed of rotation 2987 rpm
treated to VdTV 1466 NPSH required 4.18 m
Not containing chemical and Permissible operating 63.00 bar.g
mechanical substances which pressure
affect the materials Discharge press. 36.91 bar.g
Solids content max. 50 ppm
Ambient air temperature 20.0 C

Fluid temperature 120.0 C Shutoff pressure 45.60 bar.g


Fluid density 943 kg/m Min. allow. flow for short term 30.78 m/h
Fluid viscosity 0.26 mm/s operation
Suction pressure max. 1.91 bar.g Min. mass flow for stable 11.29 kg/s
Suction pressure min. 1.91 bar.g curve
NPSH available 10.00 m Min. allow. mass flow for 11.29 kg/s
Vapour pressure 1.99 bar.a continuous operation
Mass flow rate 31.43 kg/s Min. allow. mass flow short 8.06 kg/s
Max. power on curve 171.71 kW term operation
Minimum flow for stable curve 43.09 m/h Shutoff head 472.47 m
Minimum allowable flow for 43.09 m/h Max. allow. flow rate 147.75 m/h
continous operation Max. allow. mass flow 38.70 kg/s
Design Single system 1 x 100 %
Tolerances to ISO 9906 Class
3B; below 10 kW acc. to
paragraph 4.4.2
Data sheet

Customer item no.:1


Communication dated: 19/04/2017 Number: ES 4677763
Doc. no.: PT. WELTES Item no.: 100
Quantity: 1 Date: 19/04/2017
Page: 2 / 6

Multitec C 100/ 6-7.1 20.181 Version no.: 1

Design
Variant C Shaft seal code 181
Stage number 6 Sealing plan E Single acting mechanical
Balance drum with piston (external circulation)
Design Baseplate mounted, Minimum requirements for hot water quality: treatment acc. to
long-coupled VdTV regulation TCH 1466
Orientation Horizontal With SiO2-content up to max. 10 mg/l. Conductivity max. 50
Suction nominal dia. DN 125 S/cm for water with low salt content up to 160C or
Suction nominal pressure PN 25 conductivity max. 250 S/cm up to 140C for water with higher
Suction position top (0/360) salt content
Suction flange drilled EN 1092-1 Solids content up to max. 5 mg/l and no additives forming a
according to standard greasy film on the seal faces.
Discharge nominal dia. DN 100 Seal chamber design Standard seal chamber
Discharge norminal pressure PN 63 Wear ring Casing wear ring
Discharge position top (0/360) Impeller diameter 231.0 mm
Viewed from the drive Minimum impeller diameter 217.0 mm
Discharge flange drilled EN 1092-1 Full impeller diameter 241.0 mm
according to standard Free passage size 14.0 mm
Shaft seal Single acting mechanical seal Direction of rotation from drive Clockwise
Manufacturer KSB Bearing bracket construction Standard (normal) two-sided
Type 5B Bearing bracket size 100
Material code AQ1EGG Bearing seal Thrower
Bearing type Anti-friction bearings
Lubrication type Grease
Temperature sensor PT100 Without
mts
Color Ultramarine blue (RAL 5002)
KSB-blue

Driver, accessories
Driver type Electric motor Frequency 50 Hz
Drive standard mech. IEC Rated power P2 200.00 kW
Drive supplied by KSB choice Available reserve 30.62 %
Motor const. type B3 Number of poles 2
Motor size 315L

Materials 20
Notes Bearing housing (350) Grey cast iron EN-GJL-250
Unalloyed steel or cast steel components: pH = 9 to 10.5. O-Ring (412) EPDM 80
Unalloyed cast iron components: pH = 9 to 10.5 and O2 content Shaft seal housing (441) Carbon steel GP240GH+N
<= 0.02 mg/kg. Casing wear ring (502.1) Grey cast iron EN-GJL-250
Suction casing (106) Carbon steel GP240GH+N Shaft sleeve (523) Chrome steel 1.4057+QT800
Discharge casing (107) Carbon steel GP240GH+N Bush (540) Grey cast iron EN-GJL-250
Stage casing (108) Steel 1.0576 S355J2H Disc (550.1) Stainless steel 1.4301
Diffuser (171) Grey cast iron EN-GJL-250 Piston (59-4) Chrome steel
Shaft (210) Tempered steel C45+N 1.4021QT700+SR
Impeller (230) Grey cast iron EN-GJL-250 Tie bolt (905) 30NCD16
Impeller, suction stage (231) Grey cast iron EN-GJL-250
Data sheet

Customer item no.:1


Communication dated: 19/04/2017 Number: ES 4677763
Doc. no.: PT. WELTES Item no.: 100
Quantity: 1 Date: 19/04/2017
Page: 3 / 6

Multitec C 100/ 6-7.1 20.181 Version no.: 1

Packaging
Packaging category B1 Wooden or plywood case, Packaging for storage Indoor
cover provided with Outdoor storage at -40C to +50C for up to 3 months. Packet
polyproylene cellular sheet, must be covered. No corrosion protection, only transport
outdoor storage up to 3 protection.
months
Packaging for transport Truck
IPPC Standard ISPM 15 Yes
Performance curve

Customer item no.:1


Communication dated: 19/04/2017 Number: ES 4677763
Doc. no.: PT. WELTES Item no.:100
Quantity: 1 Date: 19/04/2017
Page: 4 / 6

Multitec C 100/ 6-7.1 20.181 Version no.: 1

500
Qmin

[m]
Total developed head

400

Qmax

300 231.0/A01

0 20 [m/h] 40 60 80 100 120 140 160

[m]
NPSH req.

2
0 20 [m/h] 40 60 80 100 120 140 160
Efficiency

50

[%]

0
0 20 [m/h] 40 60 80 100 120 140 160
180

[kW]
Power Input

100

40
0 20 [m/h] 40 60 80 100 120 140 160
Flow

Curve data
Speed of rotation 2987 rpm Efficiency 76.2 %
Fluid density 943 kg/m Power absorbed 153.11 kW
Viscosity 0.26 mm/s NPSH required 4.18 m
Flow rate 120.00 m/h Curve number 1777.407521/06 GG
Requested flow rate 120.00 m/h Impeller diameter 231.0 mm
Total developed head 378.48 m Acceptance standard Tolerances to ISO 9906
Requested developed head 378.47 m Class 3B; below 10 kW acc.
to paragraph 4.4.2
Installation plan

Customer item no.:1


Communication dated: 19/04/2017 Number: ES 4677763
Doc. no.: PT. WELTES Item no.:100
Quantity: 1 Date: 19/04/2017
Page: 5 / 6

Multitec C 100/ 6-7.1 20.181 Version no.: 1

329 593 472 275 275

DN1 DN2 110

275

30

235

PC748

573 462

12
35

30 35

43

504
450 40 k7
26

70 70

Drawing is not to scale Dimensions in mm

Motor Connections
Motor size 315L Suction nominal size DN1 DN 125 / EN 1092-1
Motor power 200.00 kW Discharge nominal size DN2 DN 100 / EN 1092-1
Number of poles 2 Nominal pressure suct. PN 25
Speed of rotation 2987 rpm Rated pressure disch. PN 63

Weight net
Pump 412 kg
Total 412 kg
Connect pipes without stress or strain! For auxiliary connections see
Dimensional tolerances for shaft axis height: DIN 747 separate drawing.
Dimensions without tolerances, middle tolerances to: ISO 2768-m
Connection dimensions for pumps: EN735
Dimensions without tolerances - welded parts: ISO 13920-B
Dimensions without tolerances - gray cast iron parts: ISO 8062-CT9
Connection plan

Customer item no.:1


Communication dated: 19/04/2017 Number: ES 4677763
Doc. no.: PT. WELTES Item no.:100
Quantity: 1 Date: 19/04/2017
Page: 6 / 6

Multitec C 100/ 6-7.1 20.181 Version no.: 1

1M.1 1M.2

20E.1 20E.12

8B.1 736C61BF
8B.2

6B.1 6B.2

Connections
1M.1 Pressure gauge G 1/2 Drilled and plugged.
connection
1M.2 Pressure gauge G 1/2 Drilled and plugged.
connection
6B.1 Pumped liquid drain G 1/2 Drilled and plugged.
6B.2 Pumped liquid drain G 1/2 Drilled and plugged.
8B.1 Leakage drain Rp 3/8 Drilled
8B.2 Leakage drain Rp 3/8 Drilled
20E.1 Grease nipple Mounted at the factory
20E.2 Grease nipple Mounted at the factory

You might also like