Professional Documents
Culture Documents
Over 20 years it has been able to diversify and expand its range of activities, which now
spans through such sectors as automation, design, installation, and maintenance of
electrical-instrumental plant and mechanical plant.
WORKSHOP FOR ELECTRICAL AND PNEUMATICAL ASSEMBLY WORKSHOP FOR MECHANICAL AND PIPING CONSTRUCTION
Main Activities:
dosing and mixing with tank with metering pumps and mixing reactor
Fuel skids are modular unit complete with piping, supports, tubing, valve assemblies, filters,
instrumentation, wiring on board and junction boxes and are suitable for direct fired heaters,
water bath heaters, incinerators and other combustion applications.
Engineering department develops detailed engineering starting from basic information and
technical specifications based upon well-established national and international standards.
For complete the supply set we are able to furnish burner management system (BMS) and
process control panel with programmable logic control (PLC or PCS) fully programmed with our
internal software specialist for ensure fired heater safe startup, operation and shutdown,
control and process control of packages.
FUEL GAS TREATMENT
Fuel Gas is commonly used to feed turbine engines in the power generating industry.
Preliminary fuel treatment is mandatory to ensure removal of solid, liquid and gas
contaminants.
The skids generally include a combination of tanks, piping, chemical injection pumps or
chemical transfer pumps, instrumentation, valves and control systems.
The chemical injection systems are mainly used to inject a precise and accurate amount of
chemical into a system with the required back pressure, continuously or at intervals.
Flow assurance: hydrate inhibitors, emulsion breakers, foam control and drag reduction.
1. Gas dew point heating : high-pressure natural gas heating upstream pressure regulation
stations preventing condensation phenomena due to the Joule-Thomson effect.
5. Hydrate prevention.
6. Viscosity reduction: crude oil heating upstream treatments to facilitate degassing and
dewatering.
Range:
METERING SYSTEM
SITES design fluid metering systems for accurate measurement and sampling of various
hydrocarbon liquids ranging in viscosity.
The complete system includes inlet basket strainers, air eliminators, positive displacement or
turbine flow meters, back pressure control valve, suction/discharge piping, valves,
instrumentation, controls and is designed to minimize field assembly.
The metering skid consist of a metal frame onto which pipes, ball valves, control valves,
pressure safety valves, pressure gauges , drainage system, field instrumentation and auxiliary
equipment have been installed.
Part of the ball valves upon request are equipped with electrical dives to allow
automated flow control and setting of operation.
All the valves can have the DBB design to provide dual isolation.
The standard metering system instrumentation consists of a flow meters, pressure transmitter,
temperature transmitters and a batch of controller.
HYDRAULIC POWER UNIT
Hydraulically powered valve actuators are the primary application for sites HPUs.
SITES takes care of engineering and construction of complete hydraulic system designed to
operate any number of valves from a single control center.
Hydraulic power is ideal for application requiring valve modulation, regulation or on/off
service.
With accumulator backup, sites hydraulic power units provide the perfect solution for fail-safe
and emergency shutdown applications.
HPUs are designed to provide sufficient pressure and volume to stroke valves singly or unison,
depending on customer needs.
LUBE OIL CONSOLE COOLERS
Lube oil consoles, seal oil systems and control oil systems are designed to provide
pressurized lubricating oil to various types of industrial rotating equipment.
Typically, these lube oil systems include pumps, heat exchangers, filters, controls and
instrumentation.
Lube oil consoles ( or skid ) inject uniformly clean and cool oil into bearings before,
during and after compressor operation.
Built under controlled conditions in a fabrication facility, systems are mounted on structural
steel bases designed for easy and safe transport to the end-user's facility.
Sites offer odorizing dosing packages complete with storage tanks for odorizing product
and all necessary tools to avoid any ambient contamination.
BLENDER UNITS
The Blender Unit is designed for mixing incoming products with percentages regulated by
control valves and flow transmitters and obtain different products on the out-coming lines that
are pressure controlled by control valve and pressure transmitter.
The incoming lines and the out-coming products are enabled by electrical motorized valves or
pneumatic valves.
The control system is normally done by others and is connected to all skid components by
cables directly connected from instrument to remote panel or by interposed junction boxes.
The system can be equipped by gas sensors and a signaling horn to control any gas leackage
from piping assembly.
Efficiency in oil recovery can increase from 30% (no water injection) to 51% (with water
injection).
The plant usually comprises three sections containing ceramic media but, according to the
airflow to treat and the required abatement efficiency, we can propose solutions with 2
sections, 2 sections + buffer tank or even 5 or more sections.
SITES S.r.l.
Via Trento, 82
Fax: + 39 0313520863
Email: INFO@sitessrl.com
www.sitessrl.com