Professional Documents
Culture Documents
Spec. No.
B-64305EN/03
/ Version
2. Summary of change
Basic
Function
Optional
Function
Unit
Maintenance
Parts
The section 4.11 is modified.
Notice NOTE in APPENDIX C.2.1 is modified.
Correction
Another
TITLE
TITLE
NOTE
1 The option parameters of the CNC are saved in the option information file (OPRM
INF). If this file is modified, the option parameters need to be certified because the
settings of the option parameter are assumed to be changed by FANUC Service.
Request FANUC Service to certify the option parameters.
2 Since the option information file (OPRM INF) may be necessary when the printed
circuit board is replaced, it is recommended that this file be backed up in advance
as in SRAM data.
TITLE
Spec.No.
B-64305JA/03
Version
2. Summary of changes
New, Add,
Applicable
Group Name / Outline Correct,
Date
Delete
Basic
Function
Optional
Function
Unit
Maintenance
Correction
Another
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 1/ 8
2.12 How to attach a protection cover
1. Summary
Please use a protection cover on the screen of the LCD unit in extreme environments such as oil
or dust spatters down all the time.
Unit Specification
8.4vertical LCD/MDI A02B-0319-K138
8.4horizontal LCD/MDI A02B-0319-K137
10.4LCD A02B-0319-K136
If the LCD unit has another protection cover or protection sheet for the touch panel, peel off it
from the screen. Sometimes adhesive might remain on the screen. In that case, remove it using
an adhesive tape. Wiping off with solvent may make the screen dirty.
Before attaching a protection cover, wipe off oil and smears completely from the ornamental
frame, the LCD surface and the soft key surface, using ethanol or diluted neutral detergent(such
as kitchen detergent). If you use neutral detergent, remove remaining detergent completely,
using a wet cloth. Remaining oily substance or detergent causes the protection cover to come
off the display. After you make sure that the ornamental frame is dry, follow the procedure below
to attach the protection cover. At that time, prevent dust from entering between the LCD unit and
the protection cover.
1) 10.4'' LCD
2) 8.4'' horizontal LCD/MDI
3) 8.4'' vertical LCD/MDI
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 2/ 8
1) 10.4'' LCD unit
Cut line of
Part above concave peel-off sheet
concave
of screen
DETAIL
<1> Fit the protection cover to the front of the LCD unit, locate it on the center of the display.
Make sure that the concave part of the protection cover does not overlap with the
ornamental frame of the LCD unit.
<2> Temporarily fix the upside of the protection cover.
<3> Pick up the under side of the protection cover, peel off the sheet from the upside slowly.
<2>
<1> <2>
peel-off
sheet
protection
cover
<3>
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 3/ 8
After positioning, attach the protection cover while pushing out air between the display and
protection cover toward the under side. This makes it possible to attach the protection cover
tidily. After the protection cover is positioned completely, press it firmly while scrubbing the
double sided adhesive tape part. Scrubbing the cover little by little with your fingers enhances
adhesion of the cover.
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 4/ 8
2) 8.4'' horizontal LCD/MDI unit
<1> Fit the protection cover to the front of the LCD unit, locate it on the center of the display.
Make sure that the concave part of the protection cover does not overlap with the
ornamental frame of the LCD unit.
<2> Temporarily fix the left side of the protection cover.
<3> Pick up the right side of the protection cover, peel off the sheet from the left side slowly.
<2>
protection cover
<2> <1>
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 5/ 8
After positioning, attach the protection cover while pushing out air between the display and
protection cover toward the right side. This makes it possible to attach the protection cover tidily.
After the protection cover is positioned completely, press it firmly while scrubbing the double
sided adhesive tape part. Scrubbing the cover little by little with your fingers enhances
adhesion of the protection cover.
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 6/ 8
3) 8.4'' vertical LCD/MDI unit
<1> Fit the protection cover to the front of the LCD unit, locate it on the center of the display.
Make sure that the concave part of the protection cover does not overlap with the
ornamental frame of the LCD unit.
<2> Temporarily fix the upside of the protection cover.
<3> Pick up the under side of the protection cover, peel off the sheet from the upside slowly.
<2>
<1>
<2> peel-off
sheet
protection
cover
<3>
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 7/ 8
After positioning, attach the protection cover while pushing out air between the display and
protection cover toward the under side. This makes it possible to attach the protection cover
tidily. After the protection cover is positioned completely, press it firmly while scrubbing the
double sided adhesive tape part. Scrubbing the cover little by little with your fingers enhances
adhesion of the cover.
DRAW. NO CUST
01 Nov.11, 2010 Tatemura B-64305EN/03-02
SHEET
Ed Date Design Description FANUC Corporation 8/ 8