Professional Documents
Culture Documents
rg
3. Solve Question 3 OR Questions No. 4.
4. Solve Question 5 OR Questions No. 6.
5. Solve Question 7 OR Questions No. 8.
6. Solve Question 9 OR Questions No. 10.
.O
7. Solve Question 11 OR Questions No. 12.
8. Due credit will be given to neatness and adequate dimensions.
9. Assume suitable data whenever necessary.
ts
10. Illustrate your answers whenever necessary with the help of neat sketches.
11. Answer Six questions.
1. a)
n
Design a dual input balanced output differential amplifier with a constant current bias
(using diodes) to satisfy the following requirements :
8
de
Differential Voltage gain, Ad = 40 10
Current supplied by the constant current bias circuit = 4 mA. Supply Voltage = 10 V .
OR
2. a) Define (i) Input offset current (ii) CMRR (iii) Slew rate (iv) Output offset voltage. 6
S
3. a) Develop adder subtractor circuit to give V0 4V1 2V2 10V3 V4 . Assume feedback 7
gp
resistance R f 100K .
OR
4. a) Design an Op-Amp differentiator that will differentiate an input signal in the frequency 7
range 500Hz to 2500Hz. Also draw the output waveform for the designed circuit if input is
1V peak at 2000Hz. (sine wave).
TKN/KS/16/7413/7418 1 P.T.O
b) For a Schmitt trigger using Op-Amp shown in fig. R1 50 K & R 2 1K Find the 7
value of VLT , VuT & VH . Draw Hysteresis curve.
Vin
VO
+
R1 Vsat 12V
R2
rg
OR
.O
6. a) Draw & explain R 2R ladder type D to A converter. 6
b) Draw the circuit diagram of IC 555 astable multivibrator to generate the output signal with 7
frequency 2KHz & duty cycle of 75%.
ts
7. a) Differentiate between linear regulator & Switching regulator. 4
b) Design a stepdown SMPS to give 5V, I0 8 Amp . Unregulated input is 20V. Switching 10
n
frequency is 25KHz. Assume reference voltage is 2V. Vsat 1.2 V, t sw 1.1 sec
& VDON 1V . The output ripple should be limited to less than 80mV (P P). Also calculate
de
the efficiency of SMPS.
OR
8. Design a regulated power supply to give 5V output at maximum load current of 500mA. 14
Use two transistor with h FE 60 & h FE 200 for SPT & error amplifier. Calculate
tu
Sv & R 0 .
b) Design RC phase oscillator to give frequency of oscillation 12KHz. The peak to peak output 7
should be 10 V.
ur
OR
10. a) Derive the expression for figure of merit of Colpitt's Oscillator. 7
b) Design a Wein bridge oscillator for f0 5KHz & VO PP 14V . 6
gp
11. a) Design a Butterworth filter such that the attenuation is less than 2 dB for frequency, less 9
than 400Hz & the attenuation is greater than 20 dB for frequency greater than 4KHz.
b) State the advantages of Active filter over passive filter. What is order of filter? 4
Na
OR
12. a) Design a band pass filter so that centre frequency f 0 2KHz , Q 6 & A F 10 . 7
Choose C1 C2 0.01f .
b) Write short notes on : 6
i) Design of DC Servomotor circuit.
ii) Roll of Rate in filter.
*********
TKN/KS/16/7413/7418 2