Professional Documents
Culture Documents
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness
NOTATION: The notation for Table 11.2 applies with the following modications: a and b refer to plate dimensions, and when used as subscripts for stress, they refer to the stresses in directions
parallel to the sides a and b, respectively. s is a bending stress which is positive when tensile on the bottom and compressive on the top if loadings are considered vertically downward. R is the
reaction force per unit length normal to the plate surface exerted by the boundary support on the edge of the plate. r0o is the equivalent radius of contact for a load concentrated on a very small area
Case no.,
shape, and supports Case no., loading Formulas and tabulated specic values
bqb2 aqb4
1. Rectangular plate; all 1a. Uniform over entire (At center) smax sb 2 and ymax
edges simply supported plate t Et3
(At center of long sides) Rmax gqb
a=b 1.0 1.2 1.4 1.6 1.8 2.0 3.0 4.0 5.0 1
b 0.2874 0.3762 0.4530 0.5172 0.5688 0.6102 0.7134 0.7410 0.7476 0.7500
a 0.0444 0.0616 0.0770 0.0906 0.1017 0.1110 0.1335 0.1400 0.1417 0.1421
g 0.420 0.455 0.478 0.491 0.499 0.503 0.505 0.502 0.501 0.500 (Ref. 21 for n 0:3)
3W 2b
1b. Uniform over small (At center) smax 1 n ln 0 b
2pt2 pro
concentric circle of
aWb2
radius ro (note ymax
Et3
denition of r0o )
a=b 1.0 1.2 1.4 1.6 1.8 2.0 1
[CHAP. 11
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
bW
1c. Uniform over (At center) smax sb where W qa1 b1
t2
central rectangular
11.14]
area a1 =b ab a 1:4b a 2b
b1 =b 0 0.2 0.4 0.6 0.8 1.0 0 0.2 0.4 0.8 1.2 1.4 0 0.4 0.8 1.2 1.6 2.0
0 1.82 1.38 1.12 0.93 0.76 2.0 1.55 1.12 0.84 0.75 1.64 1.20 0.97 0.78 0.64
0.2 1.82 1.28 1.08 0.90 0.76 0.63 1.78 1.43 1.23 0.95 0.74 0.64 1.73 1.31 1.03 0.84 0.68 0.57
0.4 1.39 1.07 0.84 0.72 0.62 0.52 1.39 1.13 1.00 0.80 0.62 0.55 1.32 1.08 0.88 0.74 0.60 0.50
0.6 1.12 0.90 0.72 0.60 0.52 0.43 1.10 0.91 0.82 0.68 0.53 0.47 1.04 0.90 0.76 0.64 0.54 0.44
0.8 0.92 0.76 0.62 0.51 0.42 0.36 0.90 0.76 0.68 0.57 0.45 0.40 0.87 0.76 0.63 0.54 0.44 0.38
1.0 0.76 0.63 0.52 0.42 0.35 0.30 0.75 0.62 0.57 0.47 0.38 0.33 0.71 0.61 0.53 0.45 0.38 0.30
504
Case no.,
shape, and supports Case no., loading Formulas and tabulated specic values
P, Compression
[CHAP. 11
112 0.487 0.624 0.786 1.380
by 2 0.610 0.720 0.900 1.020
3 0.713 0.750 0.792 0.750
4 0.741 0.750 0.750 0.750
In the above formulas sa and sb are stresses due to bending only; add direct stress P=t to sa (Ref. 41)
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
tension P lb=linear the following values:
in applied to all
11.14]
edges
Coef. P=PE 0 0.15 0.5 1 2 3 4 5
a=b
In the above formulas sa and sb are stresses due to bending only; add direct stress P=t to sa and sb : (Ref. 42)
bqb2 aqb4
2. Rectangular plate; three 2a. Uniform over entire smax 2 and ymax
t Et3
edges simply supported, plate
one edge (b) free
a=b 0.50 0.667 1.0 1.5 2.0 4.0
bqb2 aqb4
2d. Uniformly smax 2 and ymax
t Et3
increasing along
the a side a=b 0.50 0.667 1.0 1.5 2.0 2.5 3.0 3.5 4.0
505
506
Case no.,
shape, and supports Case no., loading Formulas and tabulated specic values
bqb2
6. Rectangular plate; two 6a. Uniform over entire (At center of long edges) smax
t2
long edges xed, two plate
aqb4
short edges simply (At center) ymax
Et3
supported
a=b 1 1.2 1.4 1.6 1.8 2 1
[CHAP. 11
b 0.4182 0.4626 0.4860 0.4968 0.4971 0.4973 0.500
a 0.0210 0.0243 0.0262 0.0273 0.0280 0.0283 0.0285
(Ref. 21)
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
b1 qb2
7. Rectangular plate; one 7a. Uniform over entire (At center of xed edge) s and R g1 qb
t2
edge xed, opposite edge plate
11.14]
b qb2
free, remaining edges (At center of free edge) s 22
t
simply supported
(At end of free edge) R g2 qb
a=b 0.25 0.50 0.75 1.0 1.5 2.0 3.0
bqb2
7d. Uniformly (At center of xed edge) s and R gqb
Flat Plates
t2
decreasing from
xed edge to free
edge a=b 0.25 0.50 0.75 1.0 1.5 2.0 3.0
Case no.,
508
shape, and supports Case no., loading Formulas and tabulated specic values
bqb 2
7dd. Uniformly (At center of xed edge) s and R gqb
t2
decreasing from
bqb2
7ddd. Uniformly (At center of xed edge) s and R gqb
t2
decreasing from
xed edge to a=b 0.25 0.50 0.75 1.0 1.5 2.0 3.0
zero at 13 b
b 0.023 0.048 0.061 0.073 0.088 0.097 0.105
g 0.115 0.149 0.159 0.164 0.167 0.168 0.168
(Ref. 49 for n 0:2)
b1 wb
7f. Distributed line load (At center of xed edge) sb and R g1 w
t2
w lb=in along free
b wb
edge (At center of free edge) sa 2 2
t
(At ends of free edge) R g2 w
b1 qb2
8. Rectangular plate, all 8a. Uniform over entire (At center of long edge) smax
t2
edges xed plate
b qb2
aqb4
(At center) s 2 2 and ymax
t Et3
[CHAP. 11
a=b 1.0 1.2 1.4 1.6 1.8 2.0 1
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
8b. Uniform over small 3W 2b aWb2
(At center) sb 1 n ln 0 b1 and ymax
11.14]
concentric circle of 2pt2 pro Et3
radius ro (note b2 W
denition of r0o ) (At center of long edge) sb
t2
b4 qb2
At x 0; z b sb
t2
a b5 qb2
At x ; z 0:45b sa max
2 t2
aqb4
ymax
Et3
510
Case no.,
shape, and supports Case no., loading Formulas and tabulated specic values
b1 qb2
b1 qb2
9aa. Uniform over 23 of At x 0; z 0 sb max and R g1 qb
t2
plate from xed
edge b2 qb2 b3 qb2
At x 0; z 0:6b sb and sa
t2 t2
At x 0; z b R g2 qb
a b4 qb2
At x ; z 0:4b sa and R g3 qb
2 t2
[CHAP. 11
b4 0.031 0.111 0.197 0.255 0.284 0.263 0.204
g1 0.115 0.230 0.334 0.423 0.517 0.542 0.543
g2 0.002 0.015 0.048 0.088 0.132 0.139 0.131
g3 0.125 0.250 0.345 0.396 0.422 0.417 0.405 (Ref. 49 for n 0:2)
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
9aaa. Uniform over 13 of b1 qb2
At x 0; z 0 sb max and R g1 qb
plate from xed t2
11.14]
edge b qb2 b3 qb2
At x 0; z 0:2b sb 2 2 and sa
t t2
At x 0; z b R g2 qb
a b4 qb2
At x ; z 0:2b sa and R g3 qb
2 t2
Case no.,
[CHAP. 11
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
10. Rectangular plate; three 10a. Uniform over entire b1 qb2
At x 0; z 0 sb max and R g1 qb
edges xed, one edge plate t2
11.14]
(a) free b qb 2
At x 0; z b sa 2 2
t
a b3 qb2
At x ; z b sa and R g2 qb
2 t2
Case no.,
[CHAP. 11
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
b1 qb2
10ddd. Uniformly At x 0; z 0 sb max and R g1 qb
t2
11.14]
decreasing from
xed edge to a b2 qb2
At x ; z 0:2b sa and R g2 qb
zero at 13 b 2 t2
b1 qb2
11. Rectangular plate; 11a. Uniform over entire At x a; z 0 sb max and R g1 qb
t2
two adjacent edges plate
xed, two remaining b b b2 qb2
edges free At x 0; z b if a > or a 0:8b if a 4 sa and R g2 qb
2 2 t2
b1 qb 2
11aa. Uniform over At x a; z 0 sb max and R g1 qb
t2
plate from z 0
to z 23 b b b b2 qb2
At x 0; z 0:6b if a > or z 0:4b if a 4 sa and R g2 qb
2 2 t2
Flat Plates
516
Case no.,
shape, and supports Case no., loading Formulas and tabulated specic values
[CHAP. 11
b2 0.026 0.059 0.089 0.107 0.116 0.113
g1 0.250 0.354 0.316 0.338 0.357 0.357
g2 0.084 0.129 0.135 0.151 0.156 0.152 (Ref. 49 for n 0:2
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
SEC.
b1 qb2
11ddd. Uniformly At x a; z 0 sb max and R g1 qb
decreasing t2
11.14]
from z 0 b2 qb 2
to z 13 b At x 0; z 0:2b sa and R g2 qb
t2
a=b 0.125 0.25 0.375 0.50 0.75 1.0
518
Case no.,
shape, and supports Case no., loading Formulas and tabulated specic values
(Ref. 14)
13bbb. Uniform over a r W
(At the corner) ymax 1:1 1:245 o
small circle of Le kL2e
radius ro , p
adjacent to a (At a distance 2:38 ro Le from the corner along diagonal)
" 0:6 #
corner 3W r
smax 2 1 1:083 o
t Le
(Ref. 14)
[CHAP. 11
y 0 30 45 60
TABLE 11.4 Formulas for at plates with straight boundaries and constant thickness (Continued )
b1 qb2
16. Parallelogram plate 16a. Uniform over entire Along longer edge toward obtuse angle) smax
SEC.
t2
(skew slab); all edges plate
b2 qb2 aqb4
xed (At center of plate) s and ymax
t2 Et3
11.14]
y a=b 1.00 1.25 1.50 1.75 2.00 2.25 2.50 3.00
0:1554qa2
At x 0; z 0:129a sx max
t2
qa4 1 n2
At x 0; z 0 ymax
81Et3
Flat Plates
520
Case no.,
shape, and supports Case no., loading Formulas and tabulated specic values
0:262qa2
0:038qa4
ymax
Et3
n 3 4 5 6 7 8 9 10 15 1
b 1.302 1.152 1.086 1.056 1.044 1.038 1.038 1.044 1.074 1.236
a 0.910 0.710 0.635 0.599 0.581 0.573 0.572 0.572 0.586 0.695
x 1.535 1.176 1.028 0.951 0.910 0.888 0.877 0.871 0.883 1.050
Number of sides n
(Ref. 55 for n 0:3
b1 qa 2
aqa 4
20. Regular polygonal 20a. Uniform over (At center ) s and ymax
t2 Et3
plate; all edges xed entire plate
b2 qa2
(At center of straight edge) smax
t2
n 3 4 5 6 7 8 9 10 1
[CHAP. 11