Professional Documents
Culture Documents
1. SPECIFICATION
Description Specification Remark
Rated voltage DC 13.5 V
Operating voltage DC 9.0 to 16.0 V
DC 7.0 to 18.0 V (CAN)
Operating temperature -30 to +80C
Storage temperature -40 to +85C
Transponder Frequency 134.2 kHz 4 kHz
Operating -40 to +85C
temperature
Max. humidity 95%
High resistant voltage 24 V
Dark current Below 7.0 mA All switches OFF, key out, all
doors LOCK and Sleep mode
Voltage drop Below 1.0 V at pin B6 and all pins for IN/OUT
BCM
korando 2010.10
02-4 8710-01
2. FUNCTIONS
1) Functional List
Applicable: O
Function
Not applicable: X
1 Wiper control Wiper mist & washer coupled wiper O
Auto washer coupled wiper O
Auto light-rain sensor coupled wiper (LIN) O
Speed sensitive intermittent wiper O
Wiper low/high control O
2 Key reminder Key reminder warning O
warning
Key reminder O
External buzzer control X
Anti-lock function when opening door O
3 Tail lamp control Tail lamp ON warning O
External lamp warning display X
Tail lamp auto OFF O
4 Door ajar warning Door status management X
Door ajar warning O
5 Seat belt control Seat belt warning O
Seat belt reminder O
6 Sunroof warning Sunroof warning control O
Sunroof warning display X
7 Room lamp control Door coupled room lamp and dimming control O
Room lamp OFF control O
Room lamp control display X
8 Key hole Key hole illumination O
illumination control
9 Defogger (heated Front defogger timer O
wire) control
Rear defogger timer O
BCM
korando 2010.10
8710-01 02-5
Applicable: O
Function
Not applicable: X
10 Keyless entry Transmitter O
control
Receiver O
Remote door lock O
Remote door unlock O
Remote panic O
Remote escort O
Auto door lock after 30 seconds O
11 Door lock/unlock Lock/unlock control by door lock switch O
control
Lock/unlock control by central door lock switch O
BCM
korando 2010.10
02-6 8710-01
Applicable: O
Function
Not applicable: X
17 Flasher (blinking) LH turn signal control O
function
RH turn signal control O
Hazard flasher switch control O
Hazard flasher indicator control X
Auto hazard flasher control O
Emergency hazard flasher control (w/ABS) O
18 DRL (Daytime DRL (Daytime Running Light) control O
Running Light)
control
19 Fog lamp control Fog lamp control O
20 Auto light control Auto light control O
(LIN)
21 Immobilizer function Key coding and synchronization O
Challenge O
CAN information O
22 Mirror Folding/unfolding control O
folding/unfolding
Auto folding/unfolding control O
control
23 Approach (puddle) Approach (puddle) lamp control O
lamp control
24 Diagnosis function Diagnostic control O
BCM
korando 2010.10
8710-01 02-7
1) Wiper Control
(1) Wiper mist & washer coupled wiper
Wiper mist
1. When turning ON the front washer switch with IGN1 ON, the front wipers operate after T1.
When releasing the switch, the wipers will stop at parking positions.
BCM
korando 2010.10
02-8 8710-01
1. When holding the front washer switch at ON position for more than T2 with IGN1 ON, the
washer fluid is sprayed onto the windshield glass and the wipers operate three times.
BCM
korando 2010.10
8710-01 02-9
2. When holding the front washer switch at ON position for more than 0.6 seconds with the
wiper switch AUTO, the washer fluid is sprayed onto the windshield glass and the wipers
operate three times. When holding it between 0.1 and 0.59 seconds, the wiper will operate
only once.
1. When turning ON the rear washer switch with key IN and IGN1 ON, the washer fluid is
sprayed onto the tailgate glass.
BCM
korando 2010.10
02-10 8710-01
1. When turning ON the auto washer switch with IGN1 ON and wiper switch OFF, the washer
fluid is sprayed onto the windshield glass for 2 seconds and the wipers operate 4 times. After
2. then, additionally, the washer fluid is sprayed for 1.5 seconds and the wipers operate 3 times
again.
3. The auto washer function is not available during the operation of auto washer coupled wiper.
The auto washer function is not available while the wiper system is in intermittent wiping
mode.
4. When turning the wiper switch to AUTO position during the operation of auto washer, the
auto washer stops its operation and the intermittent wiping mode will be started.
5. The front and rear washer function are not available during the operation of auto washer.
BCM
korando 2010.10
8710-01 02-11
BCM
korando 2010.10
02-12 8710-01
BCM
korando 2010.10
8710-01 02-13
Sensitivity adjustment
1. When increasing the wiping speed (ex: sensitivity 0 1) with volume dial with IGN2
ON, wiper switch AUTO and wiper motor stop (parking), the wipers operate one cycle
through the low relay. (only when the signal from rain sensor is "raining")
If the volume sensitivity is changed within 2 seconds, the wipers operate only one cycle.
BCM
korando 2010.10
02-14 8710-01
1. The wiper system continuously sends the wiper parking signal when the wiper parking
terminal is grounded with IGN2 ON and wiper switch AUTO.
The wiper motor runs only when the rain sensor requires the wiper operation.
2. When the parking terminal is fixed at IGN (HIGH) with IGN2 ON and wiper switch AUTO, the
wiper system sends the wiper operating signal for 2 seconds, then continuously sends the
wiper parking signal.
The wiper motor runs only when the rain sensor requires the wiper operation.
BCM
korando 2010.10
8710-01 02-15
2. When changing the volume sensitivity to "3" from "4" with IGN2 ON and wiper switch AUTO
while receiving S_COMMFAULT (communication error) signal from rain sensor, the wipers
operate one cycle through the low relay.
BCM
korando 2010.10
02-16 8710-01
BCM
korando 2010.10
8710-01 02-17
BCM
korando 2010.10
02-18 8710-01
BCM
korando 2010.10
8710-01 02-19
BCM
korando 2010.10
02-20 8710-01
BCM
korando 2010.10
8710-01 02-21
1. The buzzer sounds for 10 seconds with the interval of 0.02s ON/1.38 OFF when opening
the driver door with key removed and tail lamp ON.
2. The buzzer stops its operation when turning off the tail lamp or closing the driver door
during buzzer operation.
3. The buzzer stays ON when turning the tail lamp on again after turning it off during buzzer
operation.
4. This function is not available when the ignition switch is in ON position.
BCM
korando 2010.10
02-22 8710-01
BCM
korando 2010.10
8710-01 02-23
1. The instrument cluster module controls the door ajar warning lamp through the signals from
BCM.
2. Also, the instrument cluster module controls the blinking function according to the vehicle
speed.
BCM
korando 2010.10
02-24 8710-01
BCM
korando 2010.10
8710-01 02-25
6. Priority of buzzer operation: SBR Key reminder warning Sunroof warning Tail
lamp left ON warning Hazard flasher Turn signal lamp
BCM
korando 2010.10
02-26 8710-01
BCM
korando 2010.10
8710-01 02-27
BCM
korando 2010.10
02-28 8710-01
When opening any of doors while the room lamp switch in overhead console is pressed in
("Door" coupled position), the front and center room lamps come on. When opening the tailgate
while the luggage room lamp switch is pressed in ("Tailgate" coupled position), the luggage
room lamp comes on. If the door stays open, the room lamps automatically goes off after 10
minutes.
1. When closing the door with IGN ON, the room lamps go off immediately.
2. When closing the door with IGN OFF, the room lamps stays on for T1 and are dimmed out
for T2.
3. When turning the ignition switch to ON position during dimming out operation, the room
lamps go off immediately.
4. When receiving the door unlock signal with IGN OFF, key OUT and door closed, the room
lamps come on for T3.
5. When receiving the door unlock signal again in Step (4), the front and center room lamps
stays on for T3 additionally.
6. When opening a door during the dimming operation, the room lamps stays ON. When closing
it again, the system performs the operation in Step (1) and (2).
7. The room lamps go off immediately when entering into the theft deterrent mode.
BCM
korando 2010.10
8710-01 02-29
BCM
korando 2010.10
02-30 8710-01
BCM
korando 2010.10
8710-01 02-31
Rear defogger
1. When turning ON the rear defogger switch with IGN2 ON (engine running), the rear
defogger operates.
2. When turning OFF the rear defogger switch during the operation, the defogger stops
working.
3. The defogger operates for T1. If turning ON the defogger again in T2 after completion of the
first operation, the defogger additionally operates for T3. But, if the defogger has been
turned off by engine stop or defogger switch, this additional operation is not available.
4. The defogger stops working when turning the ignition switch to OFF position.
BCM
korando 2010.10
02-32 8710-01
1. Function
2. Data format
BCM
korando 2010.10
8710-01 02-33
Receiver
1. Operating condition
- Ignition key removed from ignition switch
2. Conditions for code registration
- The code is registered by the communication through Scan Tool.
BCM
korando 2010.10
02-34 8710-01
Remote Panic
1. When pressing (over 2.0s) the PANIC switch on the transmitter, the panic alarm is activated.
2. When receiving the panic message from the transmitter, the horn sounds and the turn signal
lamps blink for 30 seconds (Panic alarm).
BCM
korando 2010.10
8710-01 02-35
After 30 seconds delay auto door lock (Re-entering into theft deterrent mode)
1. If a door or tailgate is not opened within 30 seconds after unlocking the doors with remote
control key in theft deterrent mode, all doors will be automatically locked again (change to
theft deterrent mode). When entering into the theft deterrent mode, the turn signal lamps
blink twice and the horn sounds once.
BCM
korando 2010.10
02-36 8710-01
BCM
korando 2010.10
8710-01 02-37
BCM
korando 2010.10
02-38 8710-01
BCM
korando 2010.10
8710-01 02-39
BCM
korando 2010.10
02-40 8710-01
BCM
korando 2010.10
8710-01 02-41
- Tailgate open: REKES unlock (disarmed deterrent mode) Tailgate open signal
Tailgate open
BCM
korando 2010.10
02-42 8710-01
BCM
korando 2010.10
8710-01 02-43
2. Disarming
- When unlocking the doors or turning the ignition switch to ON position
- When receiving the door unlock signal in theft deterrent mode, all doors are unlocked and
the turn signal lamps blink once (the horn does not sound).
- When receiving the door unlock signal with the theft deterrent mode disarmed, the turn
signal lamps blink once (the horn does not sound).
BCM
korando 2010.10
02-44 8710-01
BCM
korando 2010.10
8710-01 02-45
BCM
korando 2010.10
02-46 8710-01
BCM
korando 2010.10
8710-01 02-47
BCM
korando 2010.10
02-48 8710-01
BCM
korando 2010.10
8710-01 02-49
2. Operating conditions: When receiving the emergency hazard flasher ON signal from ESP
and ABS.
When receiving the emergency hazard flasher ON: blink with the interval of 4 Hz
When receiving the emergency hazard flasher OFF: blink with the interval of 1.25 Hz (normal
operating speed).
3. However, the manual operation of the switch has a priority over this function.
OFF conditions:
- The hazard flasher blinks with the interval of 4 Hz and then lower the interval to normal
operating speed
- The hazard flasher is turned OFF when pressing the hazard flasher switch during the
emergency hazard flasher operation.
BCM
korando 2010.10
02-50 8710-01
1. When pressing the rear fog lamp switch with IGN2 ON (headlamp ON condition), the rear fog
lamps are turned ON.
2. When pressing the rear fog lamp switch again during the operation, the rear fog lamps are
turned OFF.
3. The rear fog lamps do not come ON when the engine is not running or the light switch is OFF.
4. The rear fog lamps should not automatically come on again if they have been turned OFF by
any other way other than the switch.
BCM
korando 2010.10
8710-01 02-51
BCM
korando 2010.10
02-52 8710-01
BCM
korando 2010.10
8710-01 02-53
3. When turning the ignition switch to ON position after unlocking the doors with the mirror
folded, the mirrors are unfolded automatically.
4. When the auto folding function is set, the automatic unfolding is not available if the mirrors
have been folded manually.
5. The factory setting is the enabling the auto folding function.
2. Lamp OFF:
- When receiving the door lock signal with the approach lamps ON, the lamps go OFF
(reactivation of theft deterrent mode).
- When turning the ignition switch to ON position with the approach lamps ON, the lamps
go OFF.
- The approach lamps go OFF after 30 seconds.
BCM
korando 2010.10
02-54 8710-01
BCM
korando 2010.10
8710-01 02-55
2) System Layout
BCM
korando 2010.10
02-56 8710-01
3) Operation of Immobilizer
The Immobilizer System provides an additional theft deterrent to the vehicle in which it is
installed and prevents it from being started by unauthorized persons. The transponder integrated
in the key and the engine control unit have the same code. When the ignition key with the
integrated transponder is turned to the ON position, the ECU (Engine Control Unit) checks the
crypto code of the key and, if correct, allows your vehicle to start the engine.
BCM
REKES key
Immobilizer antenna
CAN line
ECU
In the following cases, you may be unable to start the vehicle with the immobilizer.
- When two or more immobilizer keys come into contact with (each) other(s).
- When the key is close to any device sending or receiving electromagnetic fields or waves.
- When the key is close to any electronic or electric devices such as lighting equipment,
security keys or security cards.
- When the key is close to a magnetic or metal object or a battery.
BCM
korando 2010.10
8710-01 02-57
Key plate
- Avoid impact to the transponder inside of the key. The transponder can be damaged.
- With a damaged transponder, the engine cannot be started.
- When an old code should be replaced or another key is added, car owner should observe
the whole process.
- In any case, the immobilizer system cannot be removed from the vehicle. If you attempt to
remove and damage the system, it is impossible to start the engine. So never attempt to
remove, damage or modify it.
- Any remote engine starter cannot be installed to the vehicle equipped with the immobilizer
system. So never install any remote engine starter.
BCM
korando 2010.10
02-58 8710-01
BCM
korando 2010.10
8710-01 02-59
BCM
korando 2010.10
02-60 8710-01
BCM
korando 2010.10
8710-01 02-61
When one of remote control key is lost and a new remote control key is purchased, bring the
other old key to the Ssangyong Dealer or Ssangyong Authorized Service Center and have it
recoded. Otherwise, the old key will not work.
BCM
korando 2010.10
02-78 0000-00
BCM
korando 2010.10