You are on page 1of 38

CURTAIN WALL SYSTEMS JAMSTUD INTRODUCTION

CATALOG CONTENTS

OR

A Simple Choice


JamStud Value Design Considerations Section Properties Jamb Design Example Allowable Heights
p. 2 p. 3-4 p. 5-6 p. 7-8 p. 9-16


JamStud Header/Sill Header Design Example Header/Sill Allowable Curtain Wall Curtain Wall Bridging
Design p. 18 p. 19-20 Spans p. 21-29 Connections p. 30 p. 33-34

JAMSTUD NOMENCLATURE

JAMSTUD BACKGROUND


JamStud is a revolutionary addition to the light gauge steel stud industry, producing significant economies in both design and installation
when compared with conventional C Shaped studs. JamStuds unique configuration delivers increased strength and stiffness, mini-
mizing or eliminating the use of built-up jamb and header sections in a curtain wall assembly. Available in all common wall stud depths,
JamStud streamlines the design and construction process. JamStuds shape is easily differentiated from the typical c-shape, enabling

the selection of the most optimal member sizes to fit project conditions. ASIs complimentary Steel Smart System 5.0 software (page 35)
now includes the complete database of sections to quickly design both JamStud header and jamb members.
Benefits That Add Value:
Performance Improvements
Increases load capacity over a standard C-shaped stud of the same thickness
Reduces overall materials used (single JS from double or triple C-Shape common)
Provides a flat surface for attachment of door or window frame (no additional track required)
No welding or fastening built-up members together
Weight Advantages
Lighter weight results in easier handling
Less weight results in shipping efficiencies
Engineering Advantages:
Increased stiffness for deflection
Simplified jamb and header design
JamStud Increased load capacity enables selection of optimal thickness of curtain wall studs
Copyright 2009 The Steel Network Inc. All rights reserved. No part of this publication may be reproduced in whole or in part by any method without the prior written consent
of The Steel Network, Inc.

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
1 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD VALUE

ASSEMBLY COMPARISON
14 Wall Example: 600JS350-54mil JamStud compared with (2) 600S162-43 and (1) 600T125-43 members. Refer

to pages 7-8 for design methodology.

JAMSTUD SOLUTION

TYPICAL BUILT-UP JAMBS


JamStud
Built-Up
Jamb

No. of #10 Total No. of #10


Weight No. of #10
Screws to Number of Screws to Stud
Jamb Per Screws to Top
Attach #10 Screws & Jamb in Each Conclusion
Member Jamb and Bottom
Built-Up Jamb @ Each Two-Opening
(lbs) Ends of Stud
(24 o.c.) Jamb Assembly Above

JamStud is as strong as the built-up column,


600JS350-54, 2 but with 80% of the total weight and 26 fewer


39.3 (To bottom None 2 8 fasteners to install per jamb. Less materials
50ksi track**) to handle and fewer fasteners translate to
an increase in the rate of production.

The back-to-back jamb members require


(2) 600S162- two #10 screws spaced vertically at 24 on
43 + one 5 4 center. Built-up jambs require 14 times the
50.4 (To bottom 24* 28* 112** amount of screw fasteners for installation
600T125-43 track**)
purposes as opposed to the JamStud as-

section*
sembly.

* A flat surface facing the opening is typically required for attachment of the window frame. A 5 track section has been factored in the
properties of the built-up jamb, adding 8 screws for each jamb in the screw total above.
** Connection methods for supporting the header and sill, as well as wall bridging, vertical deflection, and jamb tie-downs are
not factored in the number of screws to stud as they are similar in each assembly.

The Simple Choice to Increase Your Production

A built-up, multiple
A lighter jamb member jamb with
without built-up
materials or labor. OR a significant increase
in the amount of screw
fasteners used.

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 2
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS DESIGN CONSIDERATIONS
LOAD PATHS
Tracing and verifying load paths through a structure is crucial to protect design
liability. Loads need to migrate from the roof, through the wall and floor systems,

and terminate in the foundation. JamStud transfers out-of plane wind loads from
the header and sill to the primary structural system with a single member,

simplifying the verification process. Use of a VertiClip to accommodate vertical

deflection will connect the JamStud web to the structure and provide a positive,
verifiable connection path.

The optional StiffClip CL or AL at the base of the wall resists web crippling and
delivers an effective load transfer element to the structure.

The images below illustrate the simplicity in tracing a verifiable load path in a wall
opening. Three examples are given. The example on the left shows slab-to-slab
framing, in the middle is a diagram of bypass (balloon) framing, and to the right of

that illustrates the loads at a sill and the bottom end of the JamStud .

SLAB TO SLAB FRAMING BYPASS (BALLOON) FRAMING SILL FRAMING

The largest arrows in each diagram indicate end reactions at the structure, with the medium-sized arrows signifying

the reactions from the header and sill to JamStud . The smallest arrows point to a uniform wind load. A web stiffener is

sometimes required at the top and bottom of the stud and is dependent on the end reactions present. Use of VertiClip

SL at the top and either StiffClip AL or StiffClip CL at the bottom satisfy the web stiffener requirements (if needed).

THERMAL VALUE

JamStud provides an improvement in thermal considerations over built-up sections.

(Air
(Air Flow)
Flow)


JamStud reduces the amount of materials used The additional webs in a built-up section
in the jamb, reducing the thermal bridge increases the area of the thermal bridge. In
as well as requiring less insulation. addition, insulation is required inside the cavity
or cavities created in the built-up section.

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
3 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS DESIGN CONSIDERATIONS
PRIMARY STRUCTURAL DEFLECTION
All structures deflect vertically. To prevent non-axial-load-bearing studs from carrying the weight of the structure and to protect finishes,
vertical deflection connections should be incorporated at the earliest possible moment of project design. The load-carrying capacity
of a steel stud in bending is reduced significantly when adding an axial force propagated by the bending of a primary beam or slab.
VertiClip was developed to prevent the crushing effect on non-axial-load-bearing wall studs. Non-axial-load-bearing wall studs include

exterior curtain wall and interior wall assemblies. When project conditions dictate, lateral drift and vertical deflection may be accommo-
dated through utilization of TSNs DriftClip and DriftTrak lines of connectors.

Vertical Vertical Deflection


Deflection and Lateral Drift

Finished walls frequently experience cracking, buckling, or crushing due to improper isolation of building movement. The movement of
the primary building structure is largely accounted for in horizontal member live loading. In addition to live loads, wind, seismic forces,
moisture content in materials, and temperature cycles all contribute to movement. The incorporation of vertical deflection connections
during the working drawing phase will eliminate the liability of failures and added costs associated with wall system installation.
The VertiClip and DriftClip series of mechanical connectors is a complete solution for all vertical deflection configurations. Substantial
effort has been made to standardize construction practices thus ensuring the positive connections of light steel framing components.
VertiClip has undergone extensive field and independent laboratory testing to achieve a true slip connection solution that isolates all sec-
ondary frame components from loads induced by vertical movement.

An ICC Evaluation Report for VertiClips (refer to ICC-


ESR-1903) and DriftClips (refer to ICC-ESR-2049) at
www.icc-es.org or at www.steelnetwork.com

WALL BRIDGING

As axial compression and lateral wind loads are applied, wall studs react with
weak axis buckling and torsional rotation. To offset these results, a form of
bridging is incorporated into the wall system.

The allowable load capacity of steel studs is dependant upon the presence of
securely-attached wall bridging systems at specific vertical intervals (48" or 60"
o.c.).

Bridging is typically addressed with either a channel running through the stud
punchouts securely fastened to each stud or by flat straps attached to each
stud flange.

TSN provides the industry's most effective bridging methods in BridgeClip ,

BridgeBar , and BC600/800.


More bridging information is found on page 33 of this catalog.

Each VertiClip and DriftClip is delivered to the installer with step bushings pre-installed for

accurate fastener placement. Connection examples shown on this page represent possible
application solutions. Connection use is dependant upon project load requirements. Solu-
tions are found in The Steel Networks Light Steel Framing Connection Catalog. Contact
TSNs Technical Support Team at (888) 474-4876, or technicalsupport@steelnetwork.com
for design recommendations.

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 4
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD SECTION PROPERTIES

Y Y
Material Properties: ASTM A1003/A1003M or ASTM A653/A653M,
X Grade 50 (340), 50ksi (340MPa) minimum yield strength, 65ksi (450 MPa)
minimum tensile strength, G-60 (Z180) hot-dipped galvanized coating.

JAMSTUD SECTION DIMENSIONS



JAMSTUD SECTION DIMENSIONS

Inside Design Inside Design


Overall Flange Return Return Unit Overall Flange Return Return Unit
Bend Thick- Bend Thick-
JamStud Section Depth Width Lip 1 Lip 2 Weight JamStud Section Depth Width Lip 1 Lip 2 Weight

Radius ness Radius ness


(All Studs 50ksi) (All Studs 50ksi)
D B d1 d2 R t D B d1 d2 R t
(lbs/ft) (lbs/ft)
(in) (in) (in) (in) (in) (in) (in) (in) (in) (in) (in) (in)
350JS250-33 3.5 2.5 0.589 0.5 0.105 0.0346 1.20 550JS250-33 5.5 2.5 0.589 0.5 0.105 0.0346 1.43
350JS250-43 3.5 2.5 0.610 0.5 0.105 0.0451 1.55 550JS250-43 5.5 2.5 0.610 0.5 0.105 0.0451 1.86
350JS250-54 3.5 2.5 0.633 0.5 0.105 0.0566 1.94 550JS250-54 5.5 2.5 0.633 0.5 0.105 0.0566 2.33
350JS250-68 3.5 2.5 0.663 0.5 0.105 0.0713 2.43 550JS250-68 5.5 2.5 0.663 0.5 0.105 0.0713 2.92
350JS250-97 3.5 2.5 0.723 0.5 0.105 0.1017 3.44 550JS250-97 5.5 2.5 0.723 0.5 0.105 0.1017 4.13
350JS350-68 3.5 3.5 0.663 0.5 0.105 0.0713 2.92 550JS250-118 5.5 2.5 0.768 0.5 0.105 0.1240 5.00
350JS350-97 3.5 3.5 0.723 0.5 0.105 0.1017 4.13 550JS350-68 5.5 3.5 0.663 0.5 0.105 0.0713 3.41
350JS350-118 3.5 3.5 0.768 0.5 0.105 0.1240 5.00 550JS350-97 5.5 3.5 0.723 0.5 0.105 0.1017 4.82
362JS250-33 3.625 2.5 0.589 0.5 0.105 0.0346 1.21 550JS350-118 5.5 3.5 0.768 0.5 0.105 0.1240 5.85
362JS250-43 3.625 2.5 0.610 0.5 0.105 0.0451 1.57 600JS250-33 6 2.5 0.589 0.5 0.105 0.0346 1.49
362JS250-54 3.625 2.5 0.633 0.5 0.105 0.0566 1.97 600JS250-43 6 2.5 0.610 0.5 0.105 0.0451 1.94
362JS250-68 3.625 2.5 0.663 0.5 0.105 0.0713 2.46 600JS250-54 6 2.5 0.633 0.5 0.105 0.0566 2.42
362JS250-97 3.625 2.5 0.723 0.5 0.105 0.1017 3.48 600JS250-68 6 2.5 0.663 0.5 0.105 0.0713 3.04
362JS350-68 3.625 3.5 0.663 0.5 0.105 0.0713 2.95 600JS250-97 6 2.5 0.723 0.5 0.105 0.1017 4.30
362JS350-97 3.625 3.5 0.723 0.5 0.105 0.1017 4.17 600JS250-118 6 2.5 0.768 0.5 0.105 0.1240 5.22
362JS350-118 3.625 3.5 0.768 0.5 0.105 0.1240 5.06 600JS350-68 6 3.5 0.663 0.5 0.105 0.0713 3.53
400JS250-33 4 2.5 0.589 0.5 0.105 0.0346 1.25 600JS350-97 6 3.5 0.723 0.5 0.105 0.1017 5.00
400JS250-43 4 2.5 0.610 0.5 0.105 0.0451 1.63 600JS350-118 6 3.5 0.768 0.5 0.105 0.1240 6.06
400JS250-54 4 2.5 0.633 0.5 0.105 0.0566 2.04 800JS250-43 8 2.5 0.610 0.5 0.105 0.0451 2.24
400JS250-68 4 2.5 0.663 0.5 0.105 0.0713 2.56 800JS250-54 8 2.5 0.633 0.5 0.105 0.0566 2.81
400JS250-97 4 2.5 0.723 0.5 0.105 0.1017 3.61 800JS250-68 8 2.5 0.663 0.5 0.105 0.0713 3.53
400JS350-68 4 3.5 0.663 0.5 0.105 0.0713 3.04 800JS250-97 8 2.5 0.723 0.5 0.105 0.1017 5.00
400JS350-97 4 3.5 0.723 0.5 0.105 0.1017 4.30 800JS250-118 8 2.5 0.768 0.5 0.105 0.1240 6.06
400JS350-118 4 3.5 0.768 0.5 0.105 0.1240 5.22 800JS350-68 8 3.5 0.663 0.5 0.105 0.0713 4.01
800JS350-97 8 3.5 0.723 0.5 0.105 0.1017 5.69
800JS350-118 8 3.5 0.768 0.5 0.105 0.1240 6.90
Important Notes
1. Section properties and capacities are calculated in accordance with AISI-NASPEC 2001 with 2004 Supplement
2. Tabulated gross properties are based on the full, unreduced cross section of the stud away from punchouts.
3. Effective section properties incorporate the strength increase from cold work of forming as applicable per AISI-
NASPEC, Sec. A7.2.
4. Net effective section properties are calculated at a cross section through the punchout.
y, which are calculated at a stress 0.6 Fy (service
5. For deflection calculations, use the effective moment of inertia Ix & Iy,
load level).

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
5 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD SECTION PROPERTIES

Important Notes
1. Section properties and capacities are calculated in accordance with AISI-NASPEC 2001 with 2004 Supplement
2. Tabulated gross properties are based on the full, unreduced cross section of the stud away from punchouts.
3. Effective section properties incorporate the strength increase from cold work of forming as applicable per AISI-NASPEC, Sec. A7.2.
4. Net effective section properties are calculated at a cross section through the punchout.
5. For deflection calculations, use the effective moment of inertia Ix & Iy, which are calculated at a stress 0.6 Fy (service load level).
Effective Properties if
Gross Properties (for Un-punched Sections) Effective Properties 50 ksi ("net" = Punched Sections) limited to 33 ksi Strength
JamStud
Sx Mxa Va Mxa
Section Area Ix Sx Rx Iy Ry Jx103 Cw Ro Xo m Ix Sx
(net)
Mxa
(net)
Va
(net)
Iy1 Mya1 Iy2 Mya2 Ix Mxa
(net)
(All 50 ksi) b (kips- (kips- (kips- (kips- (kips- (kips-
(in )
2
(in )
4
(in )
3
(in) (in )
4
(in) (in )
4
(in )
6
(in) (in) (in) (in )
4
(in3) (in3) (lbs) (lbs) (in4) (in4) (in4)
in) in) in) in) in) in)
350JS250-33 0.351 0.734 0.419 1.445 0.329 0.967 0.140 1.206 3.025 -2.476 1.497 0.330 0.670 0.332 0.307 9.94 9.19 1145 527 0.329 7.98 0.267 5.90 0.700 7.03 6.68
350JS250-43 0.456 0.945 0.540 1.439 0.424 0.964 0.309 1.565 3.017 -2.471 1.494 0.329 0.914 0.470 0.450 14.06 13.46 2141 747 0.424 10.67 0.372 8.56 0.945 9.94 9.70
350JS250-54 0.571 1.171 0.669 1.432 0.526 0.960 0.609 1.953 3.008 -2.465 1.491 0.329 1.171 0.595 0.578 17.81 17.31 3371 925 0.526 13.68 0.490 11.80 1.171 12.87 12.66
350JS250-68 0.715 1.450 0.829 1.424 0.653 0.955 1.212 2.443 2.996 -2.457 1.487 0.328 1.450 0.774 0.759 23.18 22.72 4208 900 0.653 17.58 0.643 16.28 1.450 18.04 17.79
350JS250-97 1.010 1.999 1.142 1.406 0.904 0.946 3.483 3.431 2.972 -2.441 1.478 0.325 1.999 1.142 1.126 38.18 37.63 5886 850 0.904 24.45 0.904 27.63 1.999 25.60 25.24
350JS350-68 0.858 1.870 1.068 1.476 1.471 1.309 1.454 5.401 3.980 -3.456 2.011 0.246 1.735 0.822 0.796 24.60 23.83 4208 900 1.471 29.02 1.449 25.62 1.849 18.07 17.66
350JS350-97 1.214 2.586 1.478 1.460 2.050 1.300 4.184 7.627 3.958 -3.441 2.004 0.244 2.551 1.284 1.256 38.45 37.60 5886 850 2.050 40.60 2.050 43.35 2.586 30.61 30.16
350JS350-118 1.471 3.082 1.761 1.448 2.457 1.293 7.538 9.227 3.941 -3.430 1.998 0.243 3.082 1.675 1.649 50.15 49.38 7073 814 2.457 48.81 2.457 52.48 3.082 37.97 37.48
362JS250-33 0.356 0.795 0.438 1.495 0.333 0.968 0.142 1.277 3.031 -2.453 1.487 0.345 0.727 0.348 0.320 10.42 9.59 1102 544 0.333 8.02 0.268 5.91 0.759 7.37 6.97
362JS250-43 0.462 1.024 0.565 1.489 0.430 0.964 0.313 1.656 3.023 -2.447 1.484 0.344 0.991 0.492 0.470 14.73 14.06 2141 802 0.430 10.72 0.373 8.59 1.024 10.41 10.14
362JS250-54 0.578 1.269 0.700 1.482 0.533 0.961 0.617 2.066 3.014 -2.442 1.481 0.344 1.269 0.623 0.604 18.65 18.09 3372 994 0.533 13.75 0.493 11.86 1.269 13.47 13.27
362JS250-68 0.724 1.573 0.868 1.474 0.662 0.956 1.227 2.583 3.002 -2.434 1.477 0.342 1.573 0.810 0.795 24.26 23.80 4375 1007 0.662 17.67 0.647 16.40 1.573 18.89 18.65
362JS250-97 1.023 2.169 1.197 1.456 0.916 0.946 3.527 3.625 2.977 -2.418 1.468 0.340 2.169 1.197 1.181 40.01 39.49 6124 954 0.916 24.58 0.916 26.16 2.169 26.83 26.48
362JS350-68 0.867 2.023 1.116 1.528 1.491 1.311 1.469 5.715 3.977 -3.430 2.001 0.256 1.877 0.860 0.834 25.74 24.96 4375 1007 1.491 29.18 1.457 25.78 2.001 18.89 18.48
362JS350-97 1.226 2.801 1.545 1.511 2.078 1.302 4.228 8.065 3.955 -3.415 1.994 0.254 2.762 1.342 1.314 40.19 39.35 6124 954 2.078 40.83 2.078 40.95 2.801 31.99 31.55
362JS350-118 1.486 3.340 1.843 1.499 2.491 1.295 7.617 9.753 3.938 -3.404 1.988 0.253 3.340 1.752 1.726 52.44 51.69 7363 917 2.491 49.09 2.491 53.57 3.340 39.72 39.24
400JS250-33 0.369 0.995 0.497 1.643 0.346 0.969 0.147 1.506 3.055 -2.386 1.458 0.390 0.912 0.398 0.361 11.91 10.80 991 589 0.346 8.14 0.269 5.94 0.951 8.40 7.86
400JS250-43 0.479 1.283 0.641 1.637 0.446 0.965 0.325 1.951 3.046 -2.381 1.455 0.389 1.242 0.561 0.530 16.80 15.87 2141 967 0.446 10.88 0.376 8.67 1.283 11.84 11.45
400JS250-54 0.599 1.591 0.796 1.630 0.554 0.962 0.640 2.432 3.037 -2.375 1.452 0.388 1.591 0.709 0.683 21.23 20.44 3372 1201 0.554 13.94 0.498 12.01 1.591 15.30 15.05
400JS250-68 0.751 1.975 0.987 1.622 0.688 0.957 1.273 3.038 3.025 -2.368 1.448 0.387 1.975 0.921 0.904 27.58 27.06 4876 1360 0.688 17.93 0.657 16.70 1.975 21.49 21.27
400JS250-97 1.061 2.730 1.365 1.604 0.953 0.948 3.658 4.255 3.000 -2.352 1.440 0.386 2.730 1.364 1.350 45.60 45.12 6839 1299 0.953 24.95 0.953 27.14 2.730 30.60 30.29
400JS350-68 0.894 2.525 1.263 1.681 1.547 1.316 1.514 6.736 3.976 -3.354 1.970 0.288 2.342 0.976 0.945 29.22 28.29 4876 1360 1.547 29.63 1.477 26.20 2.496 21.38 20.98
400JS350-97 1.265 3.503 1.751 1.664 2.158 1.306 4.360 9.488 3.953 -3.339 1.963 0.286 3.452 1.521 1.493 45.54 44.71 6839 1299 2.158 41.47 2.158 42.22 3.503 36.21 35.79
400JS350-118 1.533 4.184 2.092 1.652 2.587 1.299 7.855 11.458 3.936 -3.328 1.958 0.285 4.184 1.986 1.962 59.45 58.73 8235 1256 2.587 49.87 2.587 56.85 4.184 45.04 44.60
550JS250-33 0.421 2.063 0.750 2.215 0.390 0.962 0.168 2.703 3.239 -2.158 1.356 0.556 1.907 0.574 0.574 17.18 17.18 706 703 0.390 8.48 0.273 6.03 1.980 12.88 12.88
550JS250-43 0.547 2.667 0.970 2.209 0.503 0.959 0.371 3.497 3.230 -2.153 1.353 0.556 2.589 0.860 0.860 25.75 25.75 1570 1193 0.503 11.34 0.383 8.86 2.667 18.02 18.02
550JS250-54 0.684 3.317 1.206 2.202 0.625 0.956 0.730 4.352 3.221 -2.147 1.350 0.556 3.315 1.083 1.083 32.42 32.42 3117 1875 0.625 14.55 0.511 12.39 3.317 23.18 23.18
550JS250-68 0.858 4.129 1.501 2.194 0.776 0.951 1.454 5.423 3.208 -2.139 1.345 0.555 4.129 1.400 1.400 41.93 41.93 5350 2534 0.776 18.71 0.680 17.47 4.129 32.68 32.68
550JS250-97 1.214 5.747 2.090 2.176 1.077 0.942 4.184 7.559 3.183 -2.123 1.337 0.555 5.747 2.084 2.084 69.67 69.67 9700 3167 1.077 26.06 1.037 29.40 5.747 46.85 46.85
550JS250-118 1.471 6.881 2.502 2.163 1.285 0.935 7.538 9.058 3.163 -2.111 1.330 0.555 6.881 2.502 2.502 85.21 85.21 11723 3100 1.285 31.21 1.285 38.82 6.881 57.27 57.27
550JS350-68 1.001 5.180 1.883 2.275 1.743 1.320 1.696 12.048 4.054 -3.084 1.858 0.421 4.808 1.479 1.479 44.29 44.29 5350 2534 1.743 31.04 1.527 27.26 5.113 32.11 32.11
550JS350-97 1.417 7.228 2.629 2.259 2.434 1.311 4.886 16.898 4.029 -3.069 1.851 0.420 7.110 2.289 2.289 68.53 68.53 9700 3167 2.434 43.49 2.339 45.37 7.228 54.23 54.23
550JS350-118 1.719 8.673 3.154 2.246 2.921 1.304 8.809 20.344 4.012 -3.057 1.845 0.419 8.673 2.986 2.986 89.39 89.39 11723 3100 2.921 52.33 2.921 59.76 8.673 67.75 67.75
600JS250-33 0.438 2.522 0.841 2.400 0.402 0.958 0.175 3.209 3.326 -2.094 1.325 0.604 2.336 0.628 0.628 18.81 18.81 644 644 0.402 8.57 0.274 6.05 2.422 14.23 14.23
600JS250-43 0.569 3.261 1.087 2.394 0.519 0.955 0.386 4.150 3.317 -2.088 1.323 0.604 3.168 0.968 0.968 28.97 28.97 1432 1235 0.519 11.46 0.384 8.90 3.261 20.24 20.24
600JS250-54 0.712 4.058 1.353 2.387 0.644 0.951 0.760 5.163 3.307 -2.082 1.319 0.604 4.056 1.217 1.217 36.45 36.45 2843 1942 0.644 14.70 0.513 12.48 4.058 26.01 26.01
600JS250-68 0.894 5.055 1.685 2.378 0.801 0.947 1.514 6.431 3.295 -2.074 1.315 0.604 5.055 1.573 1.573 47.09 47.09 5350 2882 0.801 18.91 0.685 17.64 5.055 36.68 36.68
600JS250-97 1.265 7.047 2.349 2.361 1.111 0.937 4.360 8.956 3.269 -2.058 1.306 0.604 7.047 2.342 2.342 78.29 78.29 10653 3964 1.111 26.34 1.048 29.89 7.047 52.66 52.66
600JS250-118 1.533 8.447 2.816 2.348 1.327 0.930 7.855 10.726 3.250 -2.045 1.300 0.604 8.447 2.816 2.816 95.89 95.89 12885 3889 1.327 31.56 1.310 39.70 8.447 64.46 64.46
600JS350-68 1.036 6.309 2.103 2.467 1.799 1.318 1.756 14.285 4.106 -3.006 1.824 0.464 5.859 1.660 1.660 49.71 49.71 5350 2882 1.799 31.41 1.538 27.49 6.226 35.94 35.94
600JS350-97 1.468 8.816 2.939 2.451 2.513 1.308 5.061 20.020 4.081 -2.990 1.817 0.463 8.669 2.563 2.563 76.74 76.74 10653 3964 2.513 44.02 2.365 46.04 8.816 60.62 60.62
600JS350-118 1.781 10.588 3.529 2.438 3.017 1.302 9.127 24.090 4.063 -2.978 1.811 0.463 10.588 3.341 3.341 100.03 100.03 12885 3889 3.017 52.97 2.971 60.99 10.588 75.80 75.80
800JS250-43 0.659 6.378 1.595 3.110 0.572 0.931 0.447 7.513 3.746 -1.869 1.217 0.751 6.212 1.300 1.300 38.93 38.93 1060 1060 0.572 11.82 0.389 9.02 6.378 29.62 29.62
800JS250-54 0.825 7.949 1.987 3.103 0.710 0.927 0.881 9.340 3.736 -1.862 1.214 0.752 7.942 1.779 1.779 53.27 53.27 2102 2102 0.710 15.16 0.521 12.70 7.949 38.26 38.26
800JS250-68 1.036 9.923 2.481 3.095 0.883 0.923 1.756 11.624 3.724 -1.854 1.209 0.752 9.923 2.324 2.324 69.57 69.57 4219 3368 0.883 19.51 0.698 18.08 9.923 54.00 54.00
800JS250-97 1.468 13.893 3.473 3.076 1.225 0.914 5.061 16.161 3.698 -1.838 1.200 0.753 13.893 3.459 3.459 115.65 115.65 10885 6032 1.225 27.19 1.079 31.18 13.893 77.87 77.87
800JS250-118 1.781 16.707 4.177 3.063 1.464 0.907 9.127 19.330 3.679 -1.825 1.193 0.754 16.707 4.177 4.177 142.24 142.24 16182 7301 1.464 32.59 1.359 42.05 16.707 95.61 95.61

800JS350-68 1.179 12.165 3.041 3.212 1.990 1.299 1.998 25.787 4.413 -2.733 1.703 0.616 11.333 2.448 2.448 73.30 73.30 4219 3368 1.990 32.56 1.565 28.11 12.001 52.51 52.51
800JS350-97 1.671 17.065 4.266 3.195 2.782 1.290 5.762 36.082 4.388 -2.717 1.695 0.617 16.771 3.750 3.750 112.28 112.28 10885 6032 2.782 45.66 2.432 47.85 17.065 88.10 88.10
800JS350-118 2.029 20.553 5.138 3.183 3.341 1.283 10.398 43.367 4.370 -2.705 1.689 0.617 20.553 4.870 4.870 145.80 145.80 16182 7301 3.341 54.97 3.083 64.28 20.553 110.33 110.33
1
Iy and Mya are based on the web element in tension 2
Iy and Mya are based on the web element in compression

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 6
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS DESIGN EXAMPLE
DESIGNING JAMSTUD


JamStud Header

1. BASIS FOR TABLES:



The JamStud allowable heights tables in this catalog cover the following basic load combination for the Allowable Stress Design
(ASD) Method (IBC2006 and ASCE 7-05):
D + WC&C (Strength determination)

WC&C is the Component and Cladding wind load. The Dead Load (D) acting on the stud is assumed minimum
and therefore neglected in the tables.

For the deflection determination, IBC 2003, IBC2006-Sec. 1604.3 and AISI-Wall Stud Design Standard 2004, Sec. B1 allow for a
reduction factor of 0.7 on the Component and Cladding wind load (0.7WC&C).

The JamStud - Allowable Heights tables are based on the following assumptions:
4-Way distribution of lateral wind pressure acting on the opening
Opening height extends from the floor level to the bottom surface of the header
Jamb member supports wind pressure from the opening, wind pressure from half of the distance to the adjacent
stud, and header reaction

The input for the tables includes the JamStud section, opening width (ft.), opening height (ft.) design wind pressure (WC&C, psf),
and specified deflection limit. The output from the tables reflects the allowable JamStud height (ft.-in.) and the controlling
design factor, whether it is deflection or strength ("f" denotes strength, nothing denotes deflection). An * denotes critical web
crippling at support of Jamb. The use of stiffening clips at supports typically eliminates the web crippling condition.

2. DESIGN EXAMPLE
Service (un-factored) Loads:

Wind Pressure (C&C) = 30 psf


Wall Width = 6.0
Wall Height = 14.0 ft. Typical Stud: 600S162-43
Opening Width = 8.0 ft.
Opening Height = 10.0 ft
Stud Spacing = 16 o.c.
Specified Deflection Limit = L/360

Bridging (Lateral Bracing) is recommended at a vertical spacing of 60 o.c. with both JamStud flanges connected to
the sheathing.

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
7 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS DESIGN EXAMPLE
DESIGNING JAMSTUD

Use the Table:



Go to the "JamStud - Allowable Heights" table with a 6.0 in. stud member, 30 psf wind load, L/360 deflection limit, 8.0 ft. opening width,

and 10.0 ft opening height. Possible JamStud selections from the table for 14.0 ft. height are 600JS250-97 (allowable height = 15 0)
and 600JS350-68 (allowable height = 14 2). The alternative with typical 43mil cee studs results in a built-up section composed of (3)
600S162-43 capped by (2) 600T162-43.

Conclusion:

The second JamStud option, 600JS350-68, is a lighter section with less mil thickness. Use a 600JS350-68 (50ksi) (with design thick-
ness = 0.0566 and Fy = 50 ksi). Allow 2 rows of bridging for the wall (including jamb stud) arranged so that the maximum spacing does
not exceed 60 in. (5 ft.).

3. EXTRA DESIGN CONSIDERATIONS



Strength determination in the "JamStud - Allowable Heights" tables includes checks for bending and shear capacity values
of the stud and a check for lateral end reaction of the stud for web crippling. If the tables indicate a critical web crippling
(denoted with an *), you may use a clip at the top and bottom ends of the stud to eliminate the web crippling condition.

4. DESIGN COMPARISON OF JAMB MEMBERS

JamStud Solution Typical Built-Up Jamb


Typical
Design Case
Wall Stud
Section Shape Section** Shape

WC&C = 30 psf
Wall Width = 6.0 (2) Studs 600S162-43*,
Wall Height = 14.0 attached at 24 o.c. max.
vertically, capped with a
Opening Width = 6.0 600S162-43 Single 600JS250-68* closure Track 600T125-
Opening Height = 10.0 43 for window frame
Stud Spacing = 16 o.c. attachment
Deflection Limit = L/360

WC&C = 20 psf (3) Studs 362S162-43 + (1)


Wall Width = 3.625 middle Track 362T125-43,
Wall Height = 10.0 attached at 24 o.c. max.
Opening Width = 8.0 362S162-43 Single 362JS350-97 vertically, capped with a
Opening Height = 8.0 closure Track 362T125-
Stud Spacing = 16 o.c. 43 for window frame
Deflection Limit = L/600 attachment

WC&C = 35 psf
Wall Width = 8.0 (2) Studs 800S162-54,
Wall Height = 16.0 attached at 24 o.c. max.
vertically, capped with a
Opening Width = 4.0 800S162-54 Single 800JS250-54* closure Track 800T125-
Opening Height = 10.0 43 for window frame
Stud Spacing = 24 o.c. attachment
Deflection Limit = L/360

WC&C = 28 psf (4) Studs 600S162-54 + (2)


Wall Width = 6.0 Double 600JS350-68*
middle Tracks 600T125-54,
attached at 24 o.c. max.
Wall Height = 16.0 attached at 24 o.c. max.
Opening Width = 12.0 600S162-54 vertically, capped with a vertically, capped with a
closure Track 600T125- closure Track 600T125-
Opening Height = 12.0 43 for window frame
Stud Spacing = 16 o.c. 43 for window frame
attachment attachment
Deflection Limit = L/360


* Web crippling at the ends of the stud is not satisfied per AISI-Wall Stud Design Std. 2004 Sec. C4. Use VertiClip SL and

StiffClip CL or AL at the top and the bottom ends of the stud, respectively, to eliminate web crippling, or refer to TSNs Light Steel
Framing Members Catalog for web crippling load tables.
** The closure track for the window frame attachment was not considered as part of the design cross-section since it does not extend
to the full height of the jamb.

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 8
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table values not denoted by "f"
by 85% to calculate the proper JS allowable height. Table values denoted by "f" are controlled by strength and should not be reduced.
4. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
5. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
6. Limiting heights are based on continuous support of each flange over
the full length of the stud.
7. Strength determination includes checks for bending and shear
capacity values of the stud through punched section.
8. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600
6 21' 7" 16' 4" 13' 11" 12' 4" 10' 7" 8' 11" 11' 0" f 9' 7" 8' 1" 9' 11" f * 8' 11" 7' 7" 9' 1" f * 8' 5" * 7' 1" 7' 11" f * 7' 8" * 6' 6" *
4
362JS250-33, 50ksi

8 20' 4" 15' 7" 13' 6" 11' 11" 10' 5" 8' 9" 10' 10" * 9' 5" 9' 9" f * 8' 9" * 8' 11" f * 8' 3" *
8 18' 2" 14' 1" 12' 3" 11' 0" 9' 8" 8' 4" * 9' 10" f * 8' 10" * 8' 11" f * 8' 4" * 8' 2" f *
6 10 17' 8" 13' 11" 12' 3" 11' 0" *
8 16' 7" f 13' 1" 11' 6" 10' 5" f * 9' 4" * 8' 2" * 9' 3" f * 8' 8" * 8' 6" f * 8' 2" * 8' 0" f *
8 10 16' 5" 13' 1" 11' 7" 10' 5" f *
12 16' 4" 13' 1"
8 15' 1" f 12' 5" 11' 1" 10' 0" f * 9' 1" * 8' 1" * 9' 0" f * 8' 6" * 8' 5" f * 8' 1" * 8' 0" f *
10 10 15' 6" 12' 7" 11' 4" 10' 2" f *
12 15' 7" 12' 9"
6 24' 5" 18' 6" 15' 9" 13' 10" 11' 10" 9' 11" 12' 5" 10' 8" 9' 0" 11' 5" 9' 11" 8' 4" 10' 8" 9' 4" 7' 10" 9' 6" f 8' 5" 7' 2"
4
362JS250-43, 50ksi

8 23' 0" 17' 6" 15' 1" 13' 4" 11' 7" 9' 9" 12' 1" 10' 6" 8' 10" 11' 2" 9' 9" 8' 2" 10' 6" 9' 2" 9' 4" f * 8' 4" *
8 20' 6" 15' 9" 13' 7" 12' 2" 10' 8" 9' 1" 11' 1" 9' 9" 8' 4" 10' 4" 9' 1" 9' 8" f * 8' 7" * 8' 7" f *
6 10 19' 9" 15' 6" 13' 6" 12' 1" 10' 8" 11' 1" 10' 4" *
8 18' 9" 14' 7" 12' 8" 11' 5" 10' 2" 8' 10" 10' 6" 9' 4" 8' 2" * 9' 10" * 8' 10" * 9' 2" f * 8' 5" * 8' 3" f *
8 10 18' 3" 14' 5" 12' 9" 11' 6" 10' 3" 10' 7" *
12 18' 1" 14' 5" 12' 9"
8 17' 6" 13' 9" 12' 1" 11' 0" 9' 10" 8' 8" 10' 2" * 9' 2" * 8' 2" * 9' 6" f * 8' 8" * 9' 0" f * 8' 4" * 8' 2" f *
10 10 17' 2" 13' 10" 12' 3" 11' 3" * 10' 1" * 10' 5" *
12 17' 1" 13' 11" 12' 5"
6 27' 0" 20' 5" 17' 4" 15' 2" 13' 0" 10' 10" 13' 7" 11' 8" 9' 9" 12' 6" 10' 10" 9' 1" 11' 8" 10' 2" 8' 6" 10' 7" 9' 2" 7' 9"
4
362JS250-54, 50ksi

8 25' 5" 19' 4" 16' 6" 14' 7" 12' 7" 10' 7" 13' 2" 11' 5" 9' 7" 12' 2" 10' 7" 8' 11" 11' 5" 9' 11" 8' 4" 10' 4" 9' 0"
8 22' 7" 17' 3" 14' 10" 13' 2" 11' 6" 9' 10" 12' 0" 10' 6" 9' 0" 11' 2" 9' 10" 8' 5" 10' 6" 9' 3" 8' 0" 9' 7" f 8' 6"
6 10 21' 8" 16' 10" 14' 8" 13' 1" 11' 6" 12' 0" 10' 6" 11' 2" 10' 6"
8 20' 8" 15' 11" 13' 9" 12' 4" 10' 11" 9' 5" 11' 3" 10' 0" 8' 9" 10' 7" 9' 5" 8' 3" 10' 0" 9' 0" 9' 1" f * 8' 4" *
8 10 19' 11" 15' 8" 13' 9" 12' 5" 11' 0" 11' 4" 10' 1" 10' 8" 10' 1" *
12 19' 8" 15' 7" 13' 9" 12' 5"
8 19' 3" 14' 11" 13' 1" 11' 9" 10' 6" 9' 3" 10' 10" 9' 9" 8' 7" 10' 3" 9' 3" 8' 2" 9' 9" f * 8' 10"* 8' 10" f* 8' 3" *
10 10 18' 9" 14' 11" 13' 2" 12' 0" 10' 9" 11' 1" 10' 0" 10' 6" * 10' 0" f *
12 18' 6" 14' 11" 13' 3" 12' 1"
6 29' 6" 22' 3" 18' 11" 16' 6" 14' 1" 11' 8" 14' 9" 12' 8" 10' 6" 13' 7" 11' 8" 9' 9" 12' 8" 10' 11" 9' 2" 11' 5" 9' 10" 8' 4"
4
362JS250-68, 50ksi

8 27' 8" 21' 0" 17' 11" 15' 9" 13' 7" 11' 4" 14' 2" 12' 3" 10' 4" 13' 1" 11' 4" 9' 7" 12' 3" 10' 8" 9' 0" 11' 1" 9' 8" 8' 2"
8 24' 8" 18' 9" 16' 1" 14' 3" 12' 5" 10' 6" 12' 10" 11' 3" 9' 7" 11' 11" 10' 6" 9' 0" 11' 3" 9' 11" 8' 6" 10' 3" 9' 1"
6 10 23' 7" 18' 2" 15' 9" 14' 1" 12' 4" 10' 6" 12' 10" 11' 3" 11' 11" 10' 6" 11' 3" 10' 3"
8 22' 6" 17' 2" 14' 10" 13' 3" 11' 8" 10' 0" 12' 1" 10' 8" 9' 3" 11' 3" 10' 0" 8' 9" 10' 8" 9' 6" 8' 4" 9' 10" 8' 10"
8 10 21' 7" 16' 10" 14' 8" 13' 3" 11' 8" 10' 1" 12' 1" 10' 9" 11' 4" 10' 1" 10' 9"
12 21' 2" 16' 9" 14' 8" 13' 3" 12' 2"
8 20' 11" 16' 1" 14' 0" 12' 7" 11' 2" 9' 9" 11' 6" 10' 4" 9' 1" 10' 10" 9' 9" 8' 7" 10' 4" 9' 3" 8' 3" 9' 7" 8' 8"
10 10 20' 2" 15' 11" 14' 0" 12' 9" 11' 5" 10' 0" 11' 9" 10' 7" 11' 1" 10' 0" 10' 7"
12 19' 11" 15' 11" 14' 1" 12' 10"

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
9 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table values not denoted by "f"
by 85% to calculate the proper JS allowable height. Table values denoted by "f" are controlled by strength and should not be reduced.
4. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
5. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
6. Limiting heights are based on continuous support of each flange
over the full length of the stud.
7. Strength determination includes checks for bending and shear
capacity values of the stud through punched section.
8. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 33' 7" 25' 4" 21' 6" 18' 9" 16' 0" 13' 2" 16' 9" 14' 4" 11' 10" 15' 4" 13' 2" 10' 11" 14' 4" 12' 3" 10' 3" 12' 10" 11' 1" 9' 3"
4
362JS250-97, 50ksi

8 31' 7" 23' 10" 20' 4" 17' 10" 15' 4" 12' 9" 16' 0" 13' 9" 11' 6" 14' 9" 12' 9" 10' 8" 13' 9" 11' 11" 10' 0" 12' 5" 10' 10" 9' 1"
8 28' 2" 21' 3" 18' 1" 16' 0" 13' 10" 11' 7" 14' 5" 12' 6" 10' 7" 13' 4" 11' 7" 9' 11" 12' 6" 11' 0" 9' 4" 11' 5" 10' 0" 8' 7"
6 10 26' 9" 20' 5" 17' 8" 15' 8" 13' 8" 11' 7" 14' 3" 12' 6" 10' 7" 13' 3" 11' 7" 12' 6" 11' 0" 11' 5" 10' 0"
8 25' 9" 19' 5" 16' 8" 14' 9" 12' 10" 11' 0" 13' 5" 11' 9" 10' 1" 12' 5" 11' 0" 9' 6" 11' 9" 10' 5" 9' 0" 10' 9" 9' 7" 8' 5"
8 10 24' 6" 18' 10" 16' 4" 14' 8" 12' 11" 11' 1" 13' 4" 11' 10" 10' 2" 12' 6" 11' 1" 11' 10" 10' 6" 10' 10"
12 23' 9" 18' 7" 16' 3" 14' 7" 12' 11" 13' 5" 12' 6"
8 23' 10" 18' 1" 15' 7" 13' 11" 12' 3" 10' 7" 12' 8" 11' 3" 9' 10" 11' 10" 10' 7" 9' 3" 11' 3" 10' 1" 8' 11" 10' 5" 9' 4" 8' 4"
10 10 22' 10" 17' 9" 15' 6" 14' 0" 12' 5" 10' 10" 12' 10" 11' 6" 10' 1" 12' 1" 10' 10" 11' 6" 10' 4" 10' 8"
12 22' 3" 17' 7" 15' 6" 14' 1" 12' 6" 12' 11" 12' 2"
6 31' 8" 23' 11" 20' 4" 17' 9" 15' 1" 12' 5" 15' 10" 13' 6" 11' 2" 14' 6" 12' 5" 10' 4" 13' 6" 11' 8" 9' 9" 12' 2" 10' 6" 8' 10"
4
362JS350-68, 50ksi

8 29' 9" 22' 6" 19' 2" 16' 10" 14' 6" 12' 1" 15' 2" 13' 1" 10' 11" 14' 0" 12' 1" 10' 2" 13' 1" 11' 4" 9' 6" 11' 10" 10' 3" 8' 8"
8 26' 6" 20' 1" 17' 2" 15' 2" 13' 2" 11' 1" 13' 8" 11' 11" 10' 2" 12' 8" 11' 1" 9' 6" 11' 11" 10' 6" 8' 11" 10' 10" 9' 7" 8' "
6 10 25' 3" 19' 5" 16' 9" 14' 11" 13' 1" 11' 1" 13' 7" 11' 11" 10' 2" 12' 7" 11' 1" 11' 11" 10' 6" 10' 10"
8 24' 3" 18' 4" 15' 10" 14' 0" 12' 3" 10' 6" 12' 9" 11' 3" 9' 8" 11' 11" 10' 6" 9' 2" 11' 3" 10' 0" 8' 8" 10' 4" f 9' 3" 8' 1"
8 10 23' 1" 17' 11" 15' 7" 14' 0" 12' 4" 10' 7" 12' 9" 11' 4" 11' 11" 10' 7" 11' 4" 10' 1" 10' 4" f
12 22' 6" 17' 9" 15' 6" 14' 0" 12' 4" 12' 10" 12' 0"
8 22' 6" 17' 2" 14' 10" 13' 3" 11' 9" 10' 2" 12' 2" 10' 10" 9' 5" 11' 4" 10' 2" 8' 11" 10' 10" 9' 8" 8' 7" 9' 11" f 9' 1" 8' 1"
10 10 21' 7" 16' 10" 14' 10" 13' 5" 11' 11" 10' 5" 12' 4" 11' 1" 11' 7" 10' 5" 11' 1" 10' 0" 10' 1" f *
12 21' 2" 16' 10" 14' 10" 13' 6" 12' 0" 12' 5"
6 37' 0" 28' 0" 23' 9" 20' 8" 17' 7" 14' 5" 18' 5" 15' 9" 12' 11" 16' 11" 14' 5" 11' 11" 15' 9" 13' 5" 11' 2" 14' 1" 12' 1" 10' 1"
4
362JS350-97, 50ksi

8 34' 10" 26' 3" 22' 4" 19' 7" 16' 9" 13' 10" 17' 6" 15' 0" 12' 6" 16' 1" 13' 10" 11' 7" 15' 0" 13' 0" 10' 10" 13' 7" 11' 9" 9' 10"
8 31' 2" 23' 5" 19' 11" 17' 6" 15' 0" 12' 7" 15' 8" 13' 7" 11' 5" 14' 6" 12' 7" 10' 8" 13' 7" 11' 10" 10' 1" 12' 4" 10' 10" 9' 3"
6 10 29' 6" 22' 5" 19' 3" 17' 1" 14' 10" 12' 7" 15' 5" 13' 6" 11' 5" 14' 4" 12' 7" 10' 8" 13' 6" 11' 10" 10' 1" 12' 3" 10' 10"
8 28' 5" 21' 5" 18' 3" 16' 1" 13' 11" 11' 10" 14' 6" 12' 8" 10' 10" 13' 6" 11' 10" 10' 2" 12' 8" 11' 2" 9' 8" 11' 7" 10' 3" 8' 11"
8 10 26' 11" 20' 7" 17' 9" 15' 10" 13' 11" 11' 10" 14' 5" 12' 8" 10' 11" 13' 5" 11' 10" 10' 3" 12' 8" 11' 3" 11' 8" 10' 4"
12 26' 0" 20' 3" 17' 7" 15' 9" 13' 11" 14' 5" 12' 9" 13' 5" 12' 9"
8 26' 5" 19' 11" 17' 1" 15' 1" 13' 2" 11' 4" 13' 9" 12' 1" 10' 5" 12' 9" 11' 4" 9' 10" 12' 1" 10' 9" 9' 5" 11' 1" 9' 11" 8' 9"
10 10 25' 1" 19' 3" 16' 9" 15' 1" 13' 4" 11' 7" 13' 9" 12' 3" 10' 9" 12' 11" 11' 7" 10' 2" 12' 3" 11' 0" 10' 9" f 10' 3"
12 24' 4" 19' 1" 16' 9" 15' 1" 13' 5" 13' 10" 12' 4" 13' 0" 12' 4"
6 39' 11" 30' 2" 25' 7" 22' 4" 19' 0" 15' 6" 19' 11" 16' 11" 13' 10" 18' 2" 15' 6" 12' 9" 16' 11" 14' 5" 11' 11" 15' 1" 12' 11" 10' 9"
362JS350-118, 50ksi

4 8 37' 7" 28' 5" 24' 1" 21' 1" 18' 0" 14' 10" 18' 10" 16' 2" 13' 5" 17' 3" 14' 10" 12' 4" 16' 2" 13' 11" 11' 7" 14' 6" 12' 7" 10' 6"
8 33' 9" 25' 3" 21' 5" 18' 9" 16' 1" 13' 5" 16' 10" 14' 6" 12' 2" 15' 6" 13' 5" 11' 4" 14' 6" 12' 7" 10' 8" 13' 2" 11' 6" 9' 9"
6 10 31' 11" 24' 2" 20' 8" 18' 3" 15' 10" 13' 4" 16' 6" 14' 4" 12' 2" 15' 3" 13' 4" 11' 4" 14' 4" 12' 7" 10' 8" 13' 1" 11' 6"
8 30' 10" 23' 1" 19' 8" 17' 3" 14' 11" 12' 7" 15' 6" 13' 6" 11' 6" 14' 4" 12' 7" 10' 9" 13' 6" 11' 10" 10' 2" 12' 4" 10' 10" 9' 5"
8 10 29' 1" 22' 1" 19' 0" 16' 11" 14' 9" 12' 7" 15' 4" 13' 6" 11' 6" 14' 3" 12' 7" 10' 10" 13' 6" 11' 11" 10' 3" 10' 9" f 10' 9" f
12 28' 0" 21' 7" 18' 9" 16' 9" 14' 9" 12' 7" 15' 4" 13' 6" 14' 3" 12' 7" 13' 6" 12' 4"
8 28' 7" 21' 5" 18' 4" 16' 2" 14' 1" 11' 11" 14' 7" 12' 10" 11' 0" 13' 7" 11' 11" 10' 4" 12' 10" 11' 4" 9' 10" 10' 4" f 10' 4" f 9' 2"
10 10 27' 0" 20' 8" 17' 11" 16' 0" 14' 1" 12' 2" 14' 7" 12' 11" 11' 3" 13' 8" 12' 2" 10' 7" 12' 11" 11' 7" 10' 2" 10' 9" f 10' 9" f
12 26' 1" 20' 4" 17' 9" 16' 0" 14' 2" 12' 3" 14' 8" 13' 0" 13' 9" 12' 3" 12' 9" f 12' 0"

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 10
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table values not denoted by "f"
by 85% to calculate the proper JS allowable height. Table values denoted by "f" are controlled by strength and should not be reduced.
4. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
5. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
6. Limiting heights are based on continuous support of each flange
over the full length of the stud.
7. Strength determination includes checks for bending and shear
capacity values of the stud through punched section.
8. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 23' 8" 17' 11" 15' 3" 13' 5" 11' 6" 9' 7" 11' 7" f * 10' 5" 8' 9" 10' 5" f * 9' 7" * 8' 1" 9' 8" f * 9' 1" * 7' 8" * 8' 5" f * 8' 3" * 7' 0" *
4
400JS250-33, 50ksi

8 22' 3" 17' 0" 14' 7" 12' 11" * 11' 3" 9' 5" 11' 7" f * 10' 2" * 8' 7" 10' 4" f * 9' 5" * 8' 0" * 9' 5" f * 8' 11" * 8' 2" f * 8' 1" *
8 19' 10" 15' 3" 13' 3" 11' 10" f * 10' 5" 8' 11" 10' 4" f * 9' 6" * 8' 2" * 9' 4" f * 8' 11" * 8' 8" f * 8' 5" *
6 10 19' 2" 15' 0" 13' 2" 11' 10" f * 10' 5" * 10' 4" f *
8 17' 8" f 14' 2" 12' 4" 10' 11" f * 9' 11" * 8' 8" * 9' 9" f * 9' 2" * 8' 0" * 8' 11" f * 8' 8" * 8' 4" f * 8' 3" *
8 10 17' 8" f 14' 1" 12' 5" 11' 0" f * 10' 0" *
12 17' 7" 14' 1" 12' 5"
8 16' 0" f 13' 4" 11' 10" 10' 5" f * 9' 8" * 8' 6" * 9' 5" f * 9' 0" * 8' 0" * 8' 9" f * 8' 6" * 8' 3" f * 8' 2" *
10 10 16' 4" f 13' 6" 12' 0" 10' 8" f *
12 16' 8" 13' 7" 12' 1"
6 29' 7" 22' 4" 19' 0" 16' 7" 14' 2" 11' 9" 14' 10" 12' 9" 10' 7" 13' 7" 11' 9" 9' 9" 12' 9" 11' 0" 9' 2" 11' 4" f 9' 11" 8' 4"
4
400JS250-54, 50ksi

8 27' 10" 21' 1" 18' 0" 15' 10" 13' 8" 11' 5" 14' 3" 12' 4" 10' 4" 13' 2" 11' 5" 9' 7" 12' 4" 10' 9" 9' 0" 11' 2" 9' 9" 8' 2"
8 24' 9" 18' 10" 16' 1" 14' 3" 12' 5" 10' 6" 12' 11" 11' 4" 9' 8" 12' 0" 10' 6" 9' 0" 11' 4" 9' 11" 8' 6" 10' 1" f 9' 1"
6 10 23' 8" 18' 3" 15' 10" 14' 2" 12' 5" 10' 6" 12' 10" 11' 4" 12' 0" 10' 6" 11' 4" 10' 1" f *
8 22' 8" 17' 3" 14' 11" 13' 3" 11' 8" 10' 0" 12' 1" 10' 8" 9' 3" 11' 4" 10' 0" 8' 9" 10' 8" f 9' 6" 8' 4" 9' 6" f * 8' 10" *
8 10 21' 8" 16' 11" 14' 9" 13' 3" 11' 9" 10' 1" 12' 2" 10' 9" 11' 4" 10' 1" 10' 9" f *
12 21' 3" 16' 9" 14' 9" 13' 3" 12' 2"
8 21' 0" 16' 2" 14' 1" 12' 7" 11' 2" 9' 9" 11' 7" 10' 4" 9' 1" 10' 10" f 9' 9" 8' 7" 10' 2" f * 9' 4" * 8' 3" * 9' 3" f * 8' 8" *
10 10 20' 4" 16' 0" 14' 1" 12' 9" 11' 5" 10' 0" 11' 9" 10' 7" 11' 1" * 10' 0" * 10' 5" f *
12 20' 0" 16' 0" 14' 2" 12' 10"
6 36' 10" 27' 10" 23' 7" 20' 7" 17' 6" 14' 4" 18' 4" 15' 8" 12' 10" 16' 10" 14' 4" 11' 10" 15' 8" 13' 5" 11' 1" 14' 0" 12' 0" 10' 0"
4
400JS250-97, 50ksi

8 34' 8" 26' 2" 22' 3" 19' 6" 16' 8" 13' 10" 17' 5" 15' 0" 12' 6" 16' 0" 13' 10" 11' 6" 15' 0" 12' 11" 10' 10" 13' 6" 11' 8" 9' 10"
8 31' 0" 23' 3" 19' 10" 17' 5" 15' 0" 12' 7" 15' 8" 13' 6" 11' 5" 14' 5" 12' 7" 10' 7" 13' 6" 11' 10" 10' 0" 12' 3" 10' 9" 9' 2"
6 10 29' 5" 22' 4" 19' 2" 17' 0" 14' 9" 12' 6" 15' 5" 13' 5" 11' 5" 14' 3" 12' 6" 10' 8" 13' 5" 11' 10" 10' 1" 12' 3" 10' 9"
8 28' 4" 21' 3" 18' 2" 16' 0" 13' 11" 11' 9" 14' 6" 12' 8" 10' 10" 13' 5" 11' 9" 10' 1" 12' 8" 11' 2" 9' 7" 11' 7" 10' 3" 8' 11"
8 10 26' 10" 20' 6" 17' 8" 15' 9" 13' 10" 11' 10" 14' 4" 12' 8" 10' 11" 13' 5" 11' 10" 10' 2" 12' 8" 11' 3" 11' 7" 10' 4"
12 25' 11" 20' 2" 17' 7" 15' 9" 13' 10" 14' 4" 12' 8" 13' 5" 12' 8"
8 26' 3" 19' 10" 17' 0" 15' 1" 13' 2" 11' 3" 13' 8" 12' 0" 10' 5" 12' 9" 11' 3" 9' 10" 12' 0" 10' 9" 9' 5" 11' 1" 9' 11" 8' 9"
10 10 24' 11" 19' 2" 16' 8" 15' 0" 13' 3" 11' 6" 13' 9" 12' 3" 10' 8" 12' 10" 11' 6" 10' 1" 12' 3" 11' 0" 11' 4" 10' 2"
12 24' 2" 19' 0" 16' 8" 15' 0" 13' 4" 13' 10" 12' 4" 13' 0" 12' 4"
6 34' 7" 26' 2" 22' 2" 19' 5" 16' 6" 13' 6" 17' 3" 14' 9" 12' 2" 15' 10" 13' 6" 11' 2" 14' 9" 12' 7" 10' 6" 13' 2" 11' 4" 9' 6"
4
400JS350-68, 50ksi

8 32' 7" 24' 7" 20' 11" 18' 4" 15' 9" 13' 1" 16' 5" 14' 2" 11' 10" 15' 2" 13' 1" 10' 11" 14' 2" 12' 3" 10' 3" 12' 9" 11' 1" 9' 4"
8 29' 1" 21' 11" 18' 8" 16' 5" 14' 2" 11' 11" 14' 9" 12' 10" 10' 10" 13' 8" 11' 11" 10' 2" 12' 10" 11' 3" 9' 7" 11' 8" 10' 3" 8' 9"
6 10 27' 7" 21' 1" 18' 2" 16' 1" 14' 1" 11' 11" 14' 7" 12' 9" 10' 10" 13' 7" 11' 11" 10' 2" 12' 9" 11' 3" 11' 8" 10' 3"
8 26' 7" 20' 0" 17' 2" 15' 2" 13' 2" 11' 3" 13' 9" 12' 0" 10' 4" 12' 9" 11' 3" 9' 8" 12' 0" 10' 8" 9' 3" 10' 10" f 9' 10" 8' 7"
8 10 25' 3" 19' 4" 16' 9" 15' 0" 13' 2" 11' 4" 13' 8" 12' 1" 10' 5" 12' 9" 11' 4" 12' 1" 10' 9" 10' 11" f
12 24' 5" 19' 1" 16' 8" 15' 0" 13' 3" 13' 8" 12' 1" 12' 10" 12' 1"
8 24' 8" 18' 8" 16' 1" 14' 3" 12' 6" 10' 10" 13' 0" 11' 6" 10' 0" 12' 2" f 10' 10" 9' 5" 11' 5" f 10' 3" 9' 0" 10' 4" f 9' 7" 8' 6"
10 10 23' 6" 18' 2" 15' 11" 14' 4" 12' 8" 11' 1" 13' 2" 11' 9" 10' 3" 12' 4" 11' 1" 11' 9" 10' 7" 10' 7" f *
12 22' 11" 18' 1" 15' 11" 14' 4" 12' 10" 13' 3" 12' 5"

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
11 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table values not denoted by "f"
by 85% to calculate the proper JS allowable height. Table values denoted by "f" are controlled by strength and should not be reduced.
4. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
5. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
6. Limiting heights are based on continuous support of each flange
over the full length of the stud.
7. Strength determination includes checks for bending and shear
capacity values of the stud through punched section.
8. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 43' 8" 33' 1" 28' 1" 24' 6" 20' 9" 16' 11" 21' 10" 18' 6" 15' 2" 19' 11" 16' 11" 13' 11" 18' 6" 15' 9" 13' 0" 16' 6" 14' 1" 11' 8"
400JS350-118, 50ksi

4 8 41' 2" 31' 1" 26' 5" 23' 1" 19' 8" 16' 2" 20' 7" 17' 7" 14' 6" 18' 10" 16' 2" 13' 5" 17' 7" 15' 1" 12' 7" 15' 9" 13' 7" 11' 4"
8 37' 1" 27' 9" 23' 6" 20' 6" 17' 6" 14' 6" 18' 4" 15' 9" 13' 2" 16' 10" 14' 6" 12' 2" 15' 9" 13' 8" 11' 6" 14' 2" 12' 4" 10' 6"
6 10 35' 0" 26' 5" 22' 6" 19' 10" 17' 1" 14' 4" 17' 10" 15' 6" 13' 1" 16' 6" 14' 4" 12' 2" 15' 6" 13' 6" 11' 6" 14' 1" 12' 4" 10' 6"
8 33' 11" 25' 4" 21' 6" 18' 10" 16' 2" 13' 6" 16' 10" 14' 7" 12' 4" 15' 6" 13' 6" 11' 6" 14' 7" 12' 9" 10' 10" 13' 3" 11' 7" 10' 0"
8 10 31' 11" 24' 1" 20' 8" 18' 3" 15' 11" 13' 6" 16' 6" 14' 6" 12' 4" 15' 4" 13' 6" 11' 7" 14' 6" 12' 9" 10' 11" 13' 2" 11' 8" 10' 1"
12 30' 8" 23' 5" 20' 3" 18' 1" 15' 10" 13' 6" 16' 5" 14' 6" 12' 4" 15' 4" 13' 6" 14' 6" 12' 9" 13' 3"
8 31' 6" 23' 6" 20' 0" 17' 7" 15' 2" 12' 10" 15' 10" 13' 9" 11' 9" 14' 7" 12' 10" 11' 0" 13' 9" 12' 1" 10' 6" 12' 7" 11' 2" 9' 9"
10 10 29' 8" 22' 6" 19' 4" 17' 3" 15' 1" 12' 11" 15' 8" 13' 10" 11' 11" 14' 7" 12' 11" 11' 3" 13' 10" 12' 4" 10' 9" 12' 9" 11' 5" 10' 0"
12 28' 6" 22' 0" 19' 1" 17' 2" 15' 2" 13' 1" 15' 8" 13' 11" 12' 0" 14' 8" 13' 1" 13' 11" 12' 5" 12' 9" f
6 34' 7" 26' 2" 22' 2" 18' 7" f * 16' 6" * 13' 6" * 15' 6" f * 14' 9" * 12' 2" * 13' 7" f * 13' 6" * 11' 2" * 12' 3" f * 12' 3" f* 10' 6" * 10' 5" f * 10' 5" f * 9' 6" *
4
600JS250-33, 50ksi

8 32' 6" 24' 7" 20' 11" 17' 7" f * 15' 9" * 13' 1" * 15' 1" f * 14' 2" * 11' 10"* 13' 6" f * 13' 1" * 10' 11"* 12' 5" f * 12' 3" * 10' 3" * 10' 10" f * 10' 10" f* 9' 4" *
8 28' 10"f* 21' 10" 18' 8" 14' 9" f * 14' 2" * 11' 11"* 12' 10" f * 12' 10"f* 10' 10"* 11' 7" f * 11' 7" f* 10' 1" * 10' 8" f * 10' 8" f* 9' 7" * 9' 2" f * 9' 2" f * 8' 9" *
6 10 26' 11" f 21' 0" 18' 1" 15' 3" f * 14' 0" * 11' 11"* 13' 5" f * 12' 9" * 10' 10"* 12' 1" f * 11' 11" * 10' 2" * 11' 1" f * 11' 1" f*
8 24' 4" f * 20' 0" 17' 1" 13' 1" f * 13' 1" f* 11' 3" * 11' 6" f * 11' 6" f * 10' 4" * 10' 5" f * 10' 5" f* 9' 8" * 9' 5" f * 9' 5" f * 9' 3" * 8' 0" f * 8' 0" f * 8' 0" f*
8 10 23' 3" f 19' 4" 16' 9" 13' 10" f* 13' 2" * 11' 4" * 12' 4" f * 12' 1" * 10' 5" * 11' 2" f * 11' 2" f* 10' 0" f * 10' 0" f*
12 22' 11" f 19' 1" 16' 8" 14' 0" f * 13' 2" * 12' 4" f * 12' 1" *
8 21' 6" f * 18' 8" 16' 0" 12' 0" f * 12' 0" f* 10' 9" * 10' 6" f * 10' 6" f * 10' 0" * 9' 4" f * 9' 4" f * 9' 4" f * 8' 0" f * 8' 0" f * 8' 0" f * 8' 0" f * 8' 0" f * 8' 0" f*
10 10 20' 10" f 18' 2" 15' 10" 12' 10" f* 12' 8" * 11' 1" * 11' 4" f * 11' 4" f * 10' 3" * 10' 0" f * 10' 0" f* 10' 0" f * 10' 0" f*
12 20' 11" f 18' 1" 15' 11" 13' 3" f * 12' 9" *
6 39' 1" 29' 7" 25' 1" 21' 11" * 18' 7" 15' 2" 19' 6" * 16' 7" 13' 7" 17' 10" f * 15' 2" * 12' 6" 15' 11" f * 14' 2" * 11' 8" * 13' 5" f * 12' 8" * 10' 7"*
4
600JS250-43, 50ksi

8 36' 10" 27' 9" 23' 7" 20' 8" * 17' 8" 14' 7" 18' 5" * 15' 10" * 13' 2" 16' 11" f * 14' 7" * 12' 2" * 15' 5" f * 13' 8" * 11' 5" * 13' 5" f * 12' 4" * 10' 4"*
8 33' 0" 24' 9" 21' 0" 18' 5" * 15' 10" 13' 2" 16' 1" f * 14' 3" * 12' 0" 14' 5" f * 13' 2" * 11' 2" 13' 3" f * 12' 5" * 10' 6" * 11' 9" f * 11' 3" * 9' 7" *
6 10 31' 3" 23' 8" 20' 3" 17' 11" * 15' 7" 13' 1" 16' 2" * 14' 1" * 11' 11" 14' 10" f * 13' 1" * 11' 2" * 13' 7" f * 12' 4" * 10' 6" * 11' 10" f * 11' 3" *
8 30' 2" 22' 7" 19' 3" 16' 6" f * 14' 7" 12' 4" 14' 3" f * 13' 3" * 11' 3" 12' 11" f * 12' 4" * 10' 7" * 12' 0" f * 11' 8" * 10' 0" * 10' 9" f * 10' 8" * 9' 3" *
8 10 28' 6" 21' 8" 18' 8" 16' 7" * 14' 6" 12' 4" 14' 11" f * 13' 3" * 11' 4" * 13' 6" f * 12' 4" * 10' 8" * 12' 6" f * 11' 9" * 10' 1" * 11' 0" f * 10' 9" *
12 27' 5" 21' 3" 18' 5" 16' 6" * 14' 6" * 12' 5" * 15' 0" f * 13' 3" * 13' 6" f * 12' 5" * 12' 6" f *
8 27' 11" 21' 0" 17' 11" 14' 11" f* 13' 10"* 11' 9" 13' 1" f * 12' 7" * 10' 10"* 11' 11" f * 11' 9" * 10' 2" * 11' 1" f * 11' 1" f* 9' 9" * 10' 1" f * 10' 1" f * 9' 1" *
10 10 26' 6" 20' 3" 17' 7" 15' 5" f * 13' 10"* 12' 0" * 13' 11" f * 12' 9" * 11' 1" * 12' 10" f * 12' 0" * 10' 6" * 11' 11" f * 11' 5" * 10' 0" * 10' 8" f * 10' 7" *
12 25' 7" 20' 0" 17' 6" 15' 9" * 13' 11" * 12' 1" * 14' 1" f * 12' 10" * 12' 10" f * 12' 1" *
6 43' 1" 32' 8" 27' 9" 24' 2" 20' 6" 16' 9" 21' 6" 18' 3" 14' 11" 19' 8" 16' 9" 13' 9" 18' 3" * 15' 7" 12' 10" 15' 5" f * 13' 11" * 11' 6"
4
600JS250-54, 50ksi

8 40' 8" 30' 8" 26' 1" 22' 9" 19' 5" 16' 0" 20' 4" 17' 4" 14' 4" 18' 8" 16' 0" 13' 3" 17' 4" * 14' 11" 12' 5" 15' 0" f * 13' 5" * 11' 3"
8 36' 7" 27' 5" 23' 2" 20' 3" 17' 4" 14' 4" 18' 2" 15' 7" 13' 0" 16' 2" f * 14' 4" 12' 1" 14'10" f* 13' 6" 11' 4" 13' 1" f * 12' 3" * 10' 5"
6 10 34' 7" 26' 1" 22' 3" 19' 7" 16' 11" 14' 3" 17' 8" 15' 4" 12' 11" 16' 4" * 14' 3" 12' 1" 15' 2" f * 13' 5" 11' 4" 13' 2" f * 12' 2" * 10'5"*
8 33' 6" 25' 0" 21' 2" 18' 7" 16' 0" 13' 4" 16' 1" f 14' 5" 12' 2" 14' 5" f * 13' 4" 11' 4" 13' 4" f * 12' 7" * 10' 9" 11' 11" f * 11' 6" * 9' 11"
8 10 31' 7" 23' 10" 20' 5" 18' 1" 15' 9" 13' 4" 16' 4" 14' 4" 12' 3" 15' 0" f * 13' 4" 11' 5" 13'10" f* 12' 7" * 10'10"* 12' 2" f * 11' 7" * 10'0"*
12 30' 3" 23' 2" 20' 1" 17' 11" 15' 8" 13' 4" 16' 3" 14' 4" 12' 3" * 15' 0" f * 13' 4" * 13'10" f* 12' 8" * 12' 2" f *
8 31' 1" 23' 3" 19' 9" 16' 10" f 15' 0" 12' 8" 14' 7" f 13' 7" 11' 8" 13' 3" f * 12' 8" 10' 11" 12' 4" f * 12' 0" * 10' 5" * 11' 2" f * 11' 0" * 9' 8" *
10 10 29' 3" 22' 3" 19' 2" 17' 0" f 14' 11" 12' 10" 15' 3" f 13' 8" 11' 10" 14' 0" f * 12'10"* 11' 2" * 13' 1" f * 12' 2" * 10' 8" * 11' 8" f * 11' 3" *
12 28' 2" 21' 9" 18' 11" 17' 0" 15' 0" 12' 11" 15' 6" * 13' 9" * 14' 2" f * 12'11"* 13' 1" f * 12' 3" *

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 12
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table values not denoted by "f"
by 85% to calculate the proper JS allowable height. Table values denoted by "f" are controlled by strength and should not be reduced.
4. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
5. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
6. Limiting heights are based on continuous support of each flange
over the full length of the stud.
7. Strength determination includes checks for bending and shear
capacity values of the stud through punched section.
8. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 47' 0" 35' 8" 30' 4" 26' 5" 22' 5" 18' 3" 23' 6" 20' 0" 16' 4" 21' 6" 18' 3" 14'11" 20' 0" 17' 0" 13' 11" 17' 10" 15' 2" 12' 6"
4
600JS250-68, 50ksi

8 44' 5" 33' 7" 28' 6" 24' 10" 21' 2" 17' 4" 22' 2" 18' 11" 15' 7" 20' 4" 17' 4" 14' 4" 18' 11" 16' 2" 13' 5" 16' 11" 14' 7" 12' 2"
8 40' 1" 30' 0" 25' 5" 22' 2" 18' 10" 15' 7" 19' 9" 16' 11" 14' 0" 18' 1" 15' 7" 13' 0" 16' 10" f 14' 7" 12' 3" 14' 7" f 13' 2" 11' 2"
6 10 37' 11" 28' 6" 24' 3" 21' 3" 18' 4" 15' 4" 19' 1" 16' 6" 13' 11" 17' 8" 15' 4" 12'11" 16' 6" 14' 5" 12' 2" 14' 11" f 13' 1" 11' 2"
8 36' 9" 27' 5" 23' 2" 20' 3" 17' 4" 14' 5" 18' 1" 15' 7" 13' 1" 16' 4" f 14' 5" 12' 2" 14' 11" f 13' 6" 11' 6" 13' 2" f 12' 4" 10' 7"
8 10 34' 7" 26' 0" 22' 2" 19' 7" 16' 11" 14' 4" 17' 8" 15' 5" 13' 1" 16' 4" 14' 4" 12' 3" 15' 5" 13' 6" 11' 7" 13' 7" f * 12' 4" 10' 8" *
12 33' 1" 25' 2" 21' 8" 19' 3" 16' 10" 14' 4" 17' 6" 15' 4" 13' 1" 16' 3" 14' 4" 12' 3" 15' 4" 13' 6" 13' 7" f * 12' 5" *
8 34' 2" 25' 5" 21' 6" 18' 10" 16' 3" 13' 7" 16' 7" f 14' 8" 12' 5" 14' 10" f 13' 7" 11' 7" 13' 8" f 12' 10" 11' 0" 12' 3" f 11' 9" 10' 2"
10 10 32' 1" 24' 2" 20' 9" 18' 4" 16' 0" 13' 8" 16' 8" 14' 8" 12' 7" 15' 5" f 13' 8" 11'10" 14' 5" f 13' 0" 11' 3" 12' 11" f * 12' 0" * 10' 6" *
12 30' 8" 23' 6" 20' 5" 18' 3" 16' 0" 13' 9" 16' 7" 14' 8" 12' 8" 15' 6" 13' 9" 14' 7" f * 13' 1" * 12' 11" f * 12' 1" *
6 53' 7" 40' 9" 34' 8" 30' 3" 25' 8" 20' 11" 26' 11" 22' 10" 18' 7" 24' 7" 20' 11" 17' 0" 22' 10" 19' 5" 15' 10" 20' 4" 17' 4" 14' 2"
4
600JS250-97, 50ksi

8 50' 9" 38' 5" 32' 7" 28' 5" 24' 2" 19' 9" 25' 4" 21' 6" 17' 8" 23' 2" 19' 9" 16' 3" 21' 6" 18' 5" 15' 2" 19' 3" 16' 6" 13' 8"
8 46' 1" 34' 6" 29' 1" 25' 4" 21' 6" 17' 7" 22' 6" 19' 2" 15' 10" 20' 7" 17' 7" 14' 7" 19' 2" 16' 5" 13' 8" 17' 2" 14' 10" 12' 5"
6 10 43' 6" 32' 7" 27' 8" 24' 2" 20' 8" 17' 2" 21' 8" 18' 7" 15' 7" 19' 11" 17' 2" 14' 5" 18' 7" 16' 1" 13' 7" 16' 10" 14' 7" 12' 4"
8 42' 4" 31' 6" 26' 7" 23' 2" 19' 8" 16' 2" 20' 7" 17' 7" 14' 8" 18' 11" 16' 2" 13' 7" 17' 7" 15' 2" 12' 9" 15' 10" 13' 9" 11' 8"
8 10 39' 10" 29' 9" 25' 3" 22' 2" 19' 0" 15' 11" 19' 11" 17' 2" 14' 6" 18' 4" 15' 11" 13' 6" 17' 2" 15' 0" 12' 9" 15' 7" 13' 8" 11' 9"
12 37' 11" 28' 7" 24' 6" 21' 8" 18' 10" 15' 11" 19' 7" 17' 1" 14' 6" 18' 2" 15' 11" 13' 6" 17' 1" 15' 0" 12' 10" 15' 7" 13' 9"
8 39' 5" 29' 3" 24' 8" 21' 6" 18' 4" 15' 3" 19' 2" 16' 6" 13' 10" 17' 7" 15' 3" 12'10" 16' 6" 14' 4" 12' 2" 14' 11" 13' 0" 11' 2"
10 10 36' 11" 27' 8" 23' 6" 20' 8" 17' 11" 15' 2" 18' 8" 16' 3" 13' 10" 17' 3" 15' 2" 13' 0" 16' 3" 14' 4" 12' 4" 14' 10" 13' 2" 11' 5"
12 35' 2" 26' 8" 22' 11" 20' 4" 17' 9" 15' 2" 18' 6" 16' 3" 13' 11" 17' 2" 15' 2" 13' 1" 16' 3" 14' 5" 12' 5" 14' 11" 13' 3"
6 57' 5" 43' 9" 37' 3" 32' 7" 27' 8" 22' 6" 29' 0" 24' 7" 20' 0" 26' 6" 22' 6" 18' 3" 24' 7" 20' 10" 17' 0" 21' 11" 18' 7" 15' 2"
600JS250-118, 50ksi

4 8 54' 7" 41' 4" 35' 1" 30' 7" 26' 0" 21' 2" 27' 3" 23' 2" 18' 11" 24' 11" 21' 2" 17' 4" 23' 2" 19' 9" 16' 3" 20' 8" 17' 8" 14' 7"
8 49' 8" 37' 2" 31' 5" 27' 4" 23' 1" 18' 10" 24' 3" 20' 7" 16' 11" 22' 2" 18' 10" 15' 7" 20' 7" 17' 7" 14' 7" 18' 5" 15' 10" 13' 2"
6 10 46' 11" 35' 2" 29' 9" 26' 0" 22' 2" 18' 4" 23' 2" 19' 11" 16' 7" 21' 3" 18' 4" 15' 4" 19' 11" 17' 2" 14' 5" 17' 11" 15' 7" 13' 1"
8 45' 9" 34' 1" 28' 8" 24' 11" 21' 2" 17' 4" 22' 2" 18' 10" 15' 7" 20' 3" 17' 4" 14' 5" 18' 10" 16' 2" 13' 7" 16' 11" 14' 7" 12' 4"
8 10 43' 0" 32' 1" 27' 2" 23' 9" 20' 4" 16' 11" 21' 3" 18' 4" 15' 5" 19' 7" 16' 11" 14' 4" 18' 4" 15' 11" 13' 6" 16' 7" 14' 6" 12' 4"
12 40' 11" 30' 9" 26' 3" 23' 1" 20' 0" 16' 10" 20' 10" 18' 2" 15' 4" 19' 4" 16' 10" 14' 4" 18' 2" 15' 11" 13' 6" 16' 6" 14' 6" 12' 5"
8 42' 8" 31' 7" 26' 7" 23' 2" 19' 8" 16' 3" 20' 7" 17' 7" 14' 8" 18' 11" 16' 3" 13' 7" 17' 7" 15' 3" 12' 10" 15' 10" 13' 10" 11' 9"
10 10 39' 11" 29' 9" 25' 3" 22' 2" 19' 1" 16' 1" 19' 11" 17' 3" 14' 8" 18' 5" 16' 1" 13' 8" 17' 3" 15' 2" 13' 0" 15' 9" 13' 10" 12' 0"
12 37' 11" 28' 7" 24' 6" 21' 8" 18' 11" 16' 0" 19' 8" 17' 2" 14' 9" 18' 3" 16' 0" 13' 9" 17' 2" 15' 2" 13' 1" 15' 9" 13' 11" 12' 1"
6 49' 10" 37' 10" 32' 2" 28' 1" 23' 10" 19' 5" 25' 0" 21' 2" 17' 3" 22' 10" 19' 5" 15'10" 21' 2" 18' 0" 14' 9" 18' 10" f 16' 1" 13' 2"
4
600JS350-68, 50ksi

8 47' 2" 35' 8" 30' 3" 26' 5" 22' 5" 18' 4" 23' 6" 20' 0" 16' 5" 21' 6" 18' 4" 15' 2" 20' 0" 17' 1" 14' 2" 17' 8" f 15' 4" 12' 9"
8 42' 8" 31' 11" 27' 0" 23' 6" 20' 0" 16' 5" 20' 11" 17' 10" 14' 9" 19' 2" 16' 5" 13' 8" 17' 4" f 15' 4" 12' 10" 15' 0" f 13' 10" 11' 8"
6 10 40' 4" 30' 3" 25' 8" 22' 6" 19' 4" 16' 1" 20' 2" 17' 5" 14' 7" 18' 7" 16' 1" 13' 7" 17' 5" 15' 2" 12' 9" 15' 4" f 13' 9" 11' 8"
8 39' 2" 29' 2" 24' 7" 21' 6" 18' 4" 15' 2" 19' 0" f 16' 5" 13' 9" 16' 10" f 15' 2" 12' 9" 15' 4" f 14' 3" 12' 0" 13' 6" f 12' 11" 11' 0"
8 10 36' 10" 27' 7" 23' 6" 20' 8" 17' 10" 15' 0" 18' 7" 16' 2" 13' 8" 17' 0" f 15' 0" 12' 9" 15' 10" f 14' 2" 12' 1" 13' 11" f * 12' 11" 11' 1"
12 35' 2" 26' 8" 22' 10" 20' 3" 17' 8" 15' 0" 18' 5" 16' 1" 13' 8" 17' 1" 15' 0" 12'10" 15' 11" f 14' 2" 12' 1" 13' 11" f * 12'11"*
8 36' 5" 27' 1" 22' 10" 20' 0" 17' 1" 14' 3" 17' 1" f 15' 5" 13' 0" 15' 3" f 14' 3" 12' 2" 14' 0" f 13' 5" 11' 6" 12' 6" f 12' 4" 10' 7"
10 10 34' 2" 25' 8" 21' 11" 19' 4" 16' 10" 14' 4" 17' 3" f 15' 4" 13' 2" 15' 9" f 14' 4" 12' 4" 14' 9" f 13' 7" 11' 9" 13' 2" f * 12' 6" * 10' 10"*
12 32' 7" 24' 10" 21' 5" 19' 2" 16' 9" 14' 4" 17' 5" 15' 4" 13' 3" 16' 2" f 14' 4" 12'5" * 14' 11" f * 13' 8" * 13' 3" f * 12' 7" *

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
13 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table values not denoted by "f"
by 85% to calculate the proper JS allowable height. Table values denoted by "f" are controlled by strength and should not be reduced.
4. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
5. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
6. Limiting heights are based on continuous support of each flange
over the full length of the stud.
7. Strength determination includes checks for bending and shear
capacity values of the stud through punched section.
8. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600
6 58' 0" 44' 3" 37' 8" 32' 11" 27' 11" 22' 8" 29' 3" 24' 10" 20' 3" 26' 9" 22' 8" 18' 6" 24' 10" 21' 1" 17' 2" 22' 1" 18' 9" 15' 4"
4
600JS350-97, 50ksi

8 55' 2" 41' 9" 35' 5" 30' 11" 26' 3" 21' 5" 27' 6" 23' 5" 19' 1" 25' 2" 21' 5" 17' 6" 23' 5" 19' 11" 16' 4" 20' 10" 17' 10" 14' 9"
8 50' 2" 37' 7" 31' 9" 27' 7" 23' 4" 19' 1" 24' 6" 20' 10" 17' 1" 22' 5" 19' 1" 15' 9" 20' 10" 17' 9" 14' 9" 18' 7" 15' 11" 13' 4"
6 10 47' 6" 35' 6" 30' 1" 26' 3" 22' 5" 18' 6" 23' 5" 20' 1" 16' 8" 21' 6" 18' 6" 15' 6" 20' 1" 17' 4" 14' 6" 18' 1" 15' 8" 13' 3"
8 46' 3" 34' 5" 29' 0" 25' 2" 21' 4" 17' 6" 22' 5" 19' 1" 15' 9" 20' 6" 17' 6" 14' 7" 19' 1" 16' 4" 13' 8" 16' 6" f 14' 9" 12' 5"
8 10 43' 6" 32' 5" 27' 5" 24' 0" 20' 7" 17' 1" 21' 6" 18' 6" 15' 6" 19' 9" 17' 1" 14' 5" 18' 6" 16' 1" 13' 7" 16' 9" f 14' 7" 12' 6"
12 41' 4" 31' 1" 26' 6" 23' 4" 20' 2" 17' 0" 21' 0" 18' 4" 15' 6" 19' 6" 17' 0" 14' 5" 18' 4" 16' 0" 13' 8" 16' 8" 14' 7" 12' 6"
8 43' 1" 31'11" 26'11" 23' 5" 19' 10" 16' 5" 20' 10" 17' 9" 14' 10" 19' 1" 16' 5" 13' 9" 17' 4" f 15' 4" 12' 11" 15' 0" f 13' 11" 11' 10"
10 10 40' 4" 30' 1" 25' 6" 22' 4" 19' 3" 16' 2" 20' 1" 17' 5" 14' 9" 18' 7" 16' 2" 13' 10" 17' 5" 15' 3" 13' 1" 15' 7" f 14' 0" 12' 1"
12 38' 4" 28'11" 24' 9" 21' 11" 19' 0" 16' 2" 19' 10" 17' 4" 14' 10" 18' 5" 16' 2" 13' 11" 17' 4" 15' 4" 13' 2" 15' 10" 14' 1" 12' 2"
6 62' 8" 47' 10" 40' 9" 35' 8" 30' 3" 24' 7" 31' 9" 26' 11" 21' 11" 29' 0" 24' 7" 20' 0" 26' 11" 22' 10" 18' 7" 24' 0" 20' 4" 16' 7"
600JS350-118, 50ksi

4 8 59' 8" 45' 3" 38' 5" 33' 6" 28' 5" 23' 2" 29' 10" 25' 4" 20' 8" 27' 3" 23' 2" 18' 11" 25' 4" 21' 7" 17' 8" 22' 7" 19' 3" 15' 10"
8 54' 6" 40' 11" 34' 6" 30' 0" 25' 4" 20' 7" 26' 7" 22' 7" 18' 5" 24' 3" 20' 7" 16' 11" 22' 7" 19' 2" 15' 10" 20' 1" 17' 2" 14' 3"
6 10 51' 7" 38' 7" 32' 8" 28' 5" 24' 2" 19' 11" 25' 4" 21' 8" 17' 11" 23' 3" 19' 11" 16' 7" 21' 8" 18' 7" 15' 7" 19' 5" 16' 10" 14' 1"
8 50' 5" 37' 6" 31' 7" 27' 5" 23' 2" 18' 11" 24' 4" 20' 7" 16' 11" 22' 2" 18' 11" 15' 7" 20' 7" 17' 7" 14' 8" 18' 5" 15' 10" 13' 3"
8 10 47' 4" 35' 3" 29' 9" 26' 0" 22' 2" 18' 4" 23' 2" 19' 11" 16' 7" 21' 3" 18' 4" 15' 5" 19' 11" 17' 3" 14' 6" 17' 11" 15' 7" 13' 3"
12 45' 0" 33' 8" 28' 8" 25' 2" 21' 8" 18' 2" 22' 7" 19' 7" 16' 6" 20' 10" 18' 2" 15' 4" 19' 7" 17' 1" 14' 6" 17' 9" 15' 7" 13' 3"
8 47' 0" 34' 10" 29' 3" 25' 5" 21' 6" 17' 8" 22' 7" 19' 2" 15' 10" 20' 7" 17' 8" 14' 8" 19' 2" 16' 6" 13' 10" 17' 2" f 14' 11" 12' 7"
10 10 44' 0" 32' 8" 27' 8" 24' 2" 20' 8" 17' 3" 21' 8" 18' 8" 15' 9" 19' 11" 17' 3" 14' 8" 18' 8" 16' 3" 13' 10" 16' 11" 14' 10" 12' 9"
12 41' 9" 31' 3" 26' 8" 23' 6" 20' 4" 17' 3" 21' 3" 18' 6" 15' 9" 19' 8" 17' 3" 14' 9" 18' 6" 16' 3" 13' 11" 16' 10" 14' 11" 12' 10"
6 51' 0" 38' 9" 32' 11" 28' 9" * 24' 5" * 19' 10" 24'10" f * 21' 9" * 17' 8" * 21' 3" f * 19' 10" * 16' 2" * 18' 9" f * 18' 5" * 15' 1" * 15' 9" f * 15' 9" f * 13' 6" *
4
800JS250-43, 50ksi

8 48' 3" 36' 6" 31' 0" 27' 0" * 22' 11" * 18' 9" 22'11" f * 20' 6" * 16' 10" * 20' 0" f * 18' 9" * 15' 6" * 17'10" f * 17' 6" * 14' 6" * 15' 2" f * 15' 2" f * 13' 1" *
8 43' 8" 32' 8" 27' 8" 22' 4" f * 20' 5" * 16' 9" * 18' 9" f * 18' 3" * 15' 1" * 16' 5" f * 16' 5" f * 13'11" * 14' 0" f * 14' 10"f* 13' 1" * 12' 9" f * 12' 9" f * 11' 11" *
6 10 41' 3" 31' 0" 26' 3" 21' 6" f * 19' 9" * 16' 5" * 18' 5" f * 17' 9" * 14' 11" * 16' 6" f * 16' 5" * 13'10" * 15' 2" f * 15' 2" f * 13' 0" * 13' 4" f * 13' 4" f * 11' 11" *
8 40' 2" * 29' 11" 25' 3" 19' 3" f * 18' 9" * 15' 6" * 16' 3" f * 16' 3" f * 14' 0" * 14' 4" f * 14' 4" f * 13' 0" * 13' 0" f * 13' 0" f * 12' 3" * 11' 3" f * 11' 3" f * 11'3" f *

8 10 37' 1" f * 28' 3" 24' 0" 18'10" f * 18' 2" * 15' 3" * 16' 4" f * 16' 4" f * 13' 11" * 14' 9" f * 14' 9" f * 13' 0" * 13' 7" f * 13' 7" f * 12' 4" * 11' 9" f * 11' 9" f * 11' 4" *
12 34' 10" f 27' 3" 23' 4" 19' 2" f * 18' 0" * 15' 3" * 17' 0" f * 16' 5" * 13' 11" * 15' 6" f * 15' 3" * 13' 0" * 14' 3" f * 14' 3" f * 12' 4" * 12' 0" f * 12' 0" f *
8 35' 2" f * 27' 9" 23' 5" 17' 2" f * 17'2" f * 14' 7" * 14' 7" f * 14' 7" f * 13' 3" * 12'11" f * 12'11"f * 12' 4" * 11' 9" f * 11' 9" f * 11' 8" * 9' 11" f * 9' 11" f * 9'11" f *

10 10 32' 3" f * 26' 3" 22' 5" 17' 1" f * 17'1" f * 14' 7" * 14'11" f * 14'11" f * 13' 4" * 13' 6" f * 13' 6" f * 12' 6" * 12' 4" f * 12' 4" f * 11' 11" * 10' 0" f * 10' 0" f * 10'0" f *
12 30' 10" f 25' 5" 21' 11" 17' 8" f * 17' 1" * 14' 7" * 15' 9" f * 15' 8" * 13' 5" * 14' 4" f * 14' 4" f * 12' 8" * 12'11" f * 12'11" f* 12' 0" *
6 56' 1" 42' 9" 36' 4" 31' 9" * 26' 11" 21' 11" 28' 3" * 24' 0" 19' 6" 25' 10" * 21' 11" * 17' 10" 23'10" f * 20' 4" * 16' 7" * 19' 6" f * 18' 2" * 14'10" *
4
800JS250-54, 50ksi

8 53' 3" 40' 4" 34' 3" 29' 10" 25' 4" 20' 8" 26' 7" * 22' 7" * 18' 6" 24' 3" * 20' 8" * 17' 0" 21' 9" f * 19' 3" * 15'10" * 18' 3" f * 17' 3" * 14' 3" *
8 48' 5" 36' 3" 30' 7" 26' 7" * 22' 7" 18' 5" 22'11" f * 20' 1" * 16' 6" 19'11" f * 18' 5" * 15' 3" 17'11" f * 17' 2" * 14' 3" * 15' 4" f * 15' 4" f * 12'11" *
6 10 45' 9" 34' 3" 29' 0" 25' 4" * 21' 8" 17' 11" 21'11" f * 19' 5" * 16' 2" 19' 6" f * 17' 11" * 15' 0" 17'10" f * 16' 10" * 14' 1" * 15' 9" f * 15' 3" * 12'10" *
8 44' 7" 33' 2" 27' 11" 23' 7" f * 20' 7" 16' 11" 19' 8" f * 18' 5" * 15' 3" 17' 4" f * 16' 11" * 14' 1" * 15' 8" f * 15' 8" f * 13' 3" * 13' 7" f * 13' 7" f * 12' 1" *
8 10 41' 11" 31' 3" 26' 6" 22' 6" f * 19' 11" 16' 7" 19' 4" f * 17' 11" * 15' 1" 17' 4" f * 16' 7" * 14' 0" * 16' 0" f * 15' 7" * 13' 3" * 14' 3" f * 14' 3" f * 12' 2" *
12 39' 10" 30' 0" 25' 7" 22' 4" f * 19' 7" 16' 6" 19' 8" f * 17' 9" * 15' 1" 17'11" f * 16' 6" * 14' 1" * 16' 5" f * 15' 7" * 13' 3" * 14' 5" f * 14' 3" * 12' 2" *
8 41' 6" 30' 9" 25' 11" 20'10" f * 19' 2" * 15' 10" 17' 7" f * 17' 3" * 14' 4" 15' 7" f * 15' 7" f * 13' 4" * 14' 2" f * 14' 2" f * 12' 7" * 12' 5" f * 12' 5" f * 11' 7" *

10 10 38' 10" 29' 0" 24' 8" 20' 3" f * 18' 8" * 15' 9" 17' 7" f * 16' 11" * 14' 5" 15'11" f * 15' 9" * 13' 5" * 14' 9" f * 14' 9" f * 12' 9" * 13' 4" f * 13' 4" f * 11' 9" *
12 36' 11" 27' 11" 23' 11" 20' 5" f * 18' 6" 15' 9" 18' 2" f * 16' 10" * 14' 5" * 16' 8" f * 15' 9" * 13' 6" * 15' 5" f * 14' 11" * 12'10" * 13' 7" f * 13' 7" f *

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 14
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table values not denoted by "f"
by 85% to calculate the proper JS allowable height. Table values denoted by "f" are controlled by strength and should not be reduced.
4. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
5. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
6. Limiting heights are based on continuous support of each flange
over the full length of the stud.
7. Strength determination includes checks for bending and shear
capacity values of the stud through punched section.
8. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 61' 2" 46' 8" 39' 9" 34' 9" 29' 6" 24' 0" 30' 11" 26' 3" 21' 4" 28' 3" 24' 0" 19' 6" 26' 3" * 22' 3" 18' 2" 23' 4" * 19' 10" * 16' 2"
4
800JS250-68, 50ksi

8 58' 2" 44' 1" 37' 5" 32' 8" 27' 9" 22' 7" 29' 1" 24' 8" 20' 2" 26' 7" 22' 7" 18' 6" 24' 8" * 21' 0" 17' 3" 21' 6" f * 18' 9" * 15' 6"
8 53' 1" 39' 9" 33' 7" 29' 2" 24' 8" 20' 1" 25' 11" 22' 0" 18' 0" 23' 8" f * 20' 1" 16' 6" 21' 1" f * 18' 9" 15' 5" 17' 9" f * 16' 9" * 13' 11"
6 10 50' 3" 37' 7" 31' 9" 27' 9" 23' 7" 19' 5" 24' 8" 21' 1" 17' 6" 22' 7" f 19' 5" 16' 2" 20' 5" f * 18' 2" 15' 3" 17' 9" f * 16' 5" * 13' 10"
8 49' 0" 36' 6" 30' 8" 26' 8" 22' 7" 18' 5" 23' 5" f 20' 1" 16' 6" 20' 4" f * 18' 5" 15' 3" 18' 3" f * 17' 2" * 14' 4" 15' 8" f * 15' 6" * 13' 0"
8 10 46' 1" 34' 4" 29' 0" 25' 4" 21' 7" 17' 11" 22' 4" f 19' 5" 16' 3" 19' 10" f * 17' 11" 15' 1" 18' 2" f * 16' 10" 14' 3" 16' 1" f * 15' 3" * 13' 0" *
12 43' 9" 32' 10" 27' 11" 24' 6" 21' 2" 17' 9" 22' 1" 19' 2" 16' 2" 20' 2" f * 17' 9" 15' 1" 18' 8" f * 16' 9" 14' 3" 16' 3" f * 15' 3" * 13' 0" *
8 45' 9" 33' 10" 28' 6" 24' 9" 20' 11" 17' 3" 20' 8" f 18' 9" 15' 6" 18' 1" f * 17' 3" 14' 4" 16' 5" f * 16' 1" * 13' 6" 14' 3" f * 14' 3" f * 12' 4" *
10 10 42' 9" 31' 10" 26' 11" 23' 7" f 20' 3" 16' 11" 20' 1" f 18' 3" 15' 5" 18' 1" f * 16' 11" 14' 4" 16' 8" f * 15' 11" * 13' 7" 14' 11" f * 14' 7" * 12' 6" *
12 40' 7" 30' 6" 26' 0" 22' 11" 19' 11" 16' 10" 20' 5" f 18' 1" 15' 5" 18' 8" f * 16' 10" 14' 5" 17' 4" f * 15' 11" * 13' 8" * 15' 3" f * 14' 7" * 12' 7" *
6 69' 7" 53' 3" 45' 5" 39' 9" 33' 9" 27' 6" 35' 5" 30' 1" 24' 5" 32' 5" 27' 6" 22' 4" 30' 1" 25' 6" 20' 9" 26' 9" 22' 9" 18' 6"
4
800JS250-97, 50ksi

8 66' 5" 50' 6" 42' 11" 37' 5" 31' 9" 25' 10" 33' 4" 28' 3" 23' 0" 30' 5" 25' 10" 21' 1" 28' 3" 24' 0" 19' 7" 25' 2" 21' 5" 17' 7"
8 61' 0" 45' 9" 38' 8" 33' 7" 28' 4" 23' 0" 29' 9" 25' 2" 20' 6" 27' 2" 23' 0" 18' 9" 25' 2" 21' 4" 17' 6" 22' 5" 19' 1" 15' 9"
6 10 57' 10" 43' 3" 36' 6" 31' 9" 26' 11" 22' 1" 28' 3" 24' 1" 19' 9" 25' 10" 22' 1" 18' 3" 24' 1" 20' 7" 17' 1" 21' 6" 18' 6" 15' 6"
8 56' 7" 42' 1" 35' 5" 30' 8" 25' 11" 21' 0" 27' 2" 23' 0" 18' 9" 24' 9" 21' 0" 17' 3" 23' 0" 19' 7" 16' 1" 20' 6" 17' 6" 14' 7"
8 10 53' 2" 39' 7" 33' 4" 29' 0" 24' 7" 20' 3" 25' 10" 22' 0" 18' 3" 23' 7" 20' 3" 16' 11" 22' 0" 18' 11" 15' 10" 19' 9" 17' 1" 14' 5"
12 50' 6" 37' 8" 31' 11" 27' 11" 23' 11" 19' 11" 25' 0" 21' 6" 18' 1" 23' 0" 19' 11" 16' 9" 21' 6" 18' 9" 15' 10" 19' 6" 17' 0" 14' 5"
8 52' 11" 39' 2" 32' 11" 28' 6" 24' 0" 19' 7" 25' 3" 21' 4" 17' 6" 23' 0" 19' 7" 16' 2" 21' 4" 18' 3" 15' 2" 18' 7" f 16' 5" 13' 9"
10 10 49' 6" 36' 8" 30' 11" 26' 11" 22' 11" 19' 0" 24' 0" 20' 7" 17' 2" 22' 0" 19' 0" 16' 0" 20' 7" 17' 10" 15' 1" 18' 5" f 16' 2" 13' 10"
12 46' 10" 34' 11" 29' 8" 26' 0" 22' 5" 18' 10" 23' 4" 20' 3" 17' 2" 21' 7" 18' 10" 16' 0" 20' 3" 17' 9" 15' 1" 18' 5" 16' 2" 13' 11"
6 74' 7" 57' 2" 48' 10" 42' 9" 36' 5" 29' 7" 38' 2" 32' 5" 26' 4" 34' 10" 29' 7" 24' 1" 32' 5" 27' 6" 22' 4" 28' 10" 24' 6" 19' 11"
800JS250-118, 50ksi

4 8 71' 5" 54' 4" 46' 3" 40' 4" 34' 3" 27' 10" 35' 11" 30' 6" 24' 9" 32' 10" 27' 10" 22' 8" 30' 6" 25' 10" 21' 1" 27' 1" 23' 0" 18' 10"
8 65' 9" 49' 5" 41' 9" 36' 3" 30' 7" 24' 9" 32' 2" 27' 2" 22' 1" 29' 4" 24' 9" 20' 2" 27' 2" 23' 0" 18' 10" 24' 2" 20' 6" 16' 10"
6 10 62' 5" 46' 9" 39' 5" 34' 4" 29' 0" 23' 8" 30' 6" 25' 10" 21' 2" 27' 10" 23' 8" 19' 6" 25' 10" 22' 1" 18' 3" 23' 1" 19' 10" 16' 6"
8 61' 2" 45' 7" 38' 4" 33' 2" 28' 0" 22' 8" 29' 5" 24' 10" 20' 2" 26' 9" 22' 8" 18' 6" 24' 10" 21' 0" 17' 3" 22' 1" 18' 9" 15' 6"
8 10 57' 6" 42' 9" 36' 0" 31' 3" 26' 6" 21' 8" 27' 10" 23' 8" 19' 6" 25' 5" 21' 8" 18' 0" 23' 8" 20' 3" 16' 11" 21' 2" 18' 3" 15' 4"
12 54' 8" 40' 9" 34' 5" 30' 0" 25' 8" 21' 3" 26' 10" 23' 0" 19' 3" 24' 8" 21' 3" 17' 10" 23' 0" 19' 11" 16' 9" 20' 9" 18' 1" 15' 4"
8 57' 3" 42' 5" 35' 7" 30' 10" 25' 11" 21' 0" 27' 3" 23' 0" 18' 10" 24' 10" 21' 0" 17' 3" 23' 0" 19' 7" 16' 2" 20' 6" 17' 6" 14' 7"
10 10 53' 7" 39' 8" 33' 5" 29' 0" 24' 8" 20' 4" 25' 10" 22' 1" 18' 4" 23' 8" 20' 4" 17' 0" 22' 1" 19' 0" 16' 0" 19' 10" 17' 2" 14' 7"
12 50' 9" 37' 9" 31' 11" 27' 11" 23' 11" 20' 0" 25' 0" 21' 7" 18' 2" 23' 0" 20' 0" 16' 11" 21' 7" 18' 10" 16' 0" 19' 7" 17' 2" 14' 8"
6 64' 4" 49' 2" 41' 11" 36' 8" 31' 1" 25' 4" 32' 8" 27' 8" 22' 6" 29' 10" * 25' 4" 20' 7" 27' 8" * 23' 6" 19' 1" 24' 8" * 20' 11" * 17' 1"
4
800JS350-68, 50ksi

8 61' 4" 46' 6" 39' 6" 34' 6" 29' 3" 23' 10" 30' 8" 26' 0" 21' 3" 28' 0" 23' 10" 19' 5" 26' 0" * 22' 2" 18' 1" 22' 3" f * 19' 9" * 16' 3"
8 56' 1" 42' 1" 35' 6" 30' 10" 26' 1" 21' 2" 27' 4" 23' 2" 18' 11" 24' 6" f * 21' 2" 17' 4" 21' 9" f * 19' 9" * 16' 3" 18' 4" f * 17' 8" * 14' 7"
6 10 53' 1" 39' 9" 33' 7" 29' 3" 24' 10" 20' 5" 26' 0" 22' 3" 18' 4" 23' 3" f * 20' 5" 17' 0" 21' 0" f * 19' 1" 15' 11" 18' 2" f * 17' 3" * 14' 5"
8 51' 11" 38' 7" 32' 6" 28' 2" 23' 10" 19' 5" 24'2" f * 21' 2" 17' 4" 21' 0" f * 19' 5" 16' 0" 18'10" f * 18' 1" * 15' 0" 16' 1" f * 16'1" f * 13' 7" *
8 10 48' 9" 36' 3" 30' 8" 26' 8" 22' 9" 18' 10" 23' 0" f 20' 5" 17' 0" 20' 4" f * 18' 10" 15' 9" 18' 7" f * 17' 7" * 14' 10" 16' 4" f * 16' 0" * 13' 6" *
12 46' 4" 34' 8" 29' 5" 25' 10" 22' 2" 18' 7" 22'10" f 20' 1" 16' 11" 20' 7" f * 18' 7" 15' 9" 19' 1" f * 17' 6" * 14' 10" 16' 8" f * 15' 11" * 13' 7" *
8 48' 5" 35'10" 30' 2" 25' 9" f 22' 1" 18' 1" 21'4" f * 19' 9" 16' 3" 18' 8" f * 18' 1" * 15' 0" 16'10" f * 16'10"f* 14' 2" 14' 7" f * 14'7" f * 12'10"*
10 10 45' 3" 33' 8" 28' 5" 24' 3" f 21' 3" 17' 8" 20' 8" f 19' 1" 16' 1" 18' 6" f * 17' 8" 15' 0" 17' 0" f * 16' 8" * 14' 2" 15' 2" f * 15'2" f * 13' 0" *
12 42' 11" 32' 2" 27' 4" 23'10" f 20' 10" 17' 7" 20'10" f 18' 11" 16' 1" 19' 0" f * 17' 7" 15' 0" 17' 8" f * 16' 7" * 14' 3" * 15' 7" f * 15' 2" * 13' 1" *

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
15 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEIGHTS

Important Notes
1. No load factor for lateral wind pressure is used for strength determination as per ASD basic load combinations in ASCE 7-05 and
IBC 2006.
2. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC 2006, Sec. 1604.3 and AISI-Wall Stud
Design Std. 2004, Sec. B1 (Except for 5 psf lateral pressure where 1.0 load factor is used).
3. "f" denotes limiting wall height is controlled by strength. All other heights are controlled by deflection.
4. "*" denotes critical web crippling at support of Jamb based on AISI-Wall Stud Design Std. 2004 Sec. C4. Use of stiffening clips at
supports eliminate the web crippling condition.
5. Limiting heights are based on continuous support of each flange over the full length of the stud.
6. Strength determination includes checks for bending and shear capacity values
of the stud through punched section.
7. Values for multi-span and load bearing conditions are available.
Contact TSN's Technical Support Team for recommendations.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Height (ft)
Width (ft)
JamStud

Opening

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 74' 9" 57' 3" 48'11" 42' 10" 36' 5" 29' 8" 38' 2" 32' 5" 26' 5" 34' 11" 29' 8" 24' 1" 32' 5" 27' 7" 22' 5" 28' 11" 24' 6" 19' 11"
4
800JS350-97, 50ksi

8 71' 6" 54' 5" 46' 3" 40' 5" 34' 3" 27' 10" 36' 0" 30' 6" 24'10" 32' 10" 27' 10" 22' 8" 30' 6" 25' 11" 21' 1" 27' 2" 23' 1" 18' 10"
8 65' 11" 49' 6" 41'10" 36' 4" 30' 8" 24' 10" 32' 3" 27' 3" 22' 1" 29' 4" 24' 10" 20' 3" 27' 3" 23' 1" 18' 10" 23' 10" f 20' 7" 16' 10"
6 10 62' 6" 46'10" 39' 6" 34' 4" 29' 1" 23' 9" 30' 6" 25' 11" 21' 3" 27' 10" 23' 9" 19' 6" 25' 11" 22' 1" 18' 3" 22' 8" f 19' 10" 16' 6"
8 61' 3" 45' 8" 38' 5" 33' 3" 28' 0" 22' 8" 29' 5" 24' 10" 20' 2" 26' 10" 22' 8" 18' 6" 24' 7" f 21' 1" 17' 3" 20' 6" f 18' 10" 15' 7"
8 10 57' 8" 42'10" 36' 1" 31' 4" 26' 7" 21' 9" 27' 10" 23' 8" 19' 6" 25' 5" 21' 9" 18' 0" 23' 4" f 20' 3" 16' 11" 19' 11" f 18' 3" 15' 4"
12 54' 9" 40' 9" 34' 5" 30' 1" 25' 8" 21' 3" 26' 10" 23' 1" 19' 3" 24' 8" 21' 3" 17' 10" 23' 1" f 19' 11" 16' 10" 20' 3" f 18' 1" 15' 4"
8 57' 5" 42' 6" 35' 8" 30' 10" 26' 0" 21' 1" 27' 4" 23' 1" 18'10" 24' 5" f 21' 1" 17' 4" 21' 8" f 19' 7" 16' 2" 18' 3" f 17' 7" 14' 8"
10 10 53' 8" 39' 9" 33' 6" 29' 1" 24' 8" 20' 4" 25' 10" 22' 1" 18' 4" 23' 2" f 20' 4" 17' 0" 20' 11" f 19' 0" 16' 0" 18' 2" f 17' 3" 14' 7"
12 50' 10" 37'10" 32' 0" 28' 0" 24' 0" 20' 0" 25' 1" 21' 7" 18' 2" 22' 11" f 20' 0" 16' 11" 21' 1" f 18' 10" 16' 0" 18' 9" f 17' 2" 14' 8"
6 80' 8" 62' 0" 53' 0" 46' 5" 39' 6" 32' 2" 41' 5" 35' 3" 28' 8" 37' 11" 32' 2" 26' 2" 35' 3" 29' 11" 24' 4" 31' 4" 26' 7" 21' 8"
800JS350-118, 50ksi

4 8 77' 5" 59' 0" 50' 3" 43' 10" 37' 3" 30' 3" 39' 1" 33' 2" 26'11" 35' 8" 30' 3" 24' 7" 33' 2" 28' 1" 22' 11" 29' 6" 25' 0" 20' 5"
8 71' 7" 53'10" 45' 6" 39' 7" 33' 5" 27' 0" 35' 1" 29' 7" 24' 0" 31' 11" 27' 0" 21' 11" 29' 7" 25' 1" 20' 5" 26' 3" 22' 3" 18' 3"
6 10 68' 0" 51' 0" 43' 0" 37' 4" 31' 7" 25' 8" 33' 2" 28' 1" 22'11" 30' 3" 25' 8" 21' 1" 28' 1" 23' 11" 19' 8" 25' 1" 21' 5" 17' 9"
8 66' 8" 49' 9" 41'10" 36' 3" 30' 6" 24' 8" 32' 1" 27' 0" 21'11" 29' 2" 24' 8" 20' 1" 27' 0" 22' 10" 18' 8" 24' 0" 20' 4" 16' 9"
8 10 62' 10" 46' 9" 39' 4" 34' 1" 28' 10" 23' 6" 30' 3" 25' 8" 21' 1" 27' 7" 23' 6" 19' 5" 25' 8" 21' 11" 18' 2" 22' 11" 19' 8" 16' 5"
12 59' 8" 44' 5" 37' 6" 32' 8" 27' 9" 22' 11" 29' 1" 24' 10" 20' 8" 26' 8" 22' 11" 19' 1" 24' 10" 21' 5" 18' 0" 22' 4" 19' 5" 16' 4"
8 62' 7" 46' 5" 38'11" 33' 8" 28' 4" 22' 11" 29' 9" 25' 1" 20' 5" 27' 1" 22' 11" 18' 8" 25' 1" 21' 3" 17' 5" 21' 4" f 19' 0" 15' 8"
10 10 58' 8" 43' 5" 36' 6" 31' 8" 26' 9" 21' 11" 28' 1" 23' 11" 19' 9" 25' 8" 21' 11" 18' 3" 23' 11" 20' 6" 17' 1" 20' 8" f 18' 6" 15' 7"
12 55' 6" 41' 2" 34' 9" 30' 4" 25' 10" 21' 6" 27' 1" 23' 3" 19' 5" 24' 10" 21' 6" 18' 1" 23' 3" 20' 2" 17' 1" 20' 10" f 18' 4" 15' 7"

Also use JamStud in Header Assemblies

Reduces overall materials used


Speeds installation
Fewer fasteners
Simple Inspection

Span tables begin on page 21.


Standard
JamStud Track
Header Cee Stud


OR Cee Stud
Standard
Track
JamStud
One Stud Box Two Stud Box
JamStud Header Header Header
* The top track seen in the assemblies above is to capture the cripple
studs above and does not factor in the design of the header.

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 16
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS PROJECT EXAMPLES


Use of JamStud as jambs and openings on this 8 story project saved the contractor significant time

and labor expenses. With the high amount of openings (500+) it is easy to see how JamStud posi-

tively benefits installation. Use of JamStud in lieu of built-up jambs and headers cut materials by
over 50% and reduced labor associated with the built-up materials.

Example of a opening made of multiple (S)


section studs. Seven studs and 2 tracks are
utilized in this jamb, creating a significant
increase in both materials and labor costs.
By taking advantage of TSN's free value
engineering service or by utilizing the Quick

Member Selector in Steel Smart System
software (SSS), the design could have been
optimized using far fewer members. A com-
plimentary license of SSS is available at
www.steelsmartsystem.com.

The Simple Choice to Increase Your Production

A built-up, multiple
A lighter jamb member jamb with
without built-up
materials or labor. OR a significant increase
in the amount of screw
fasteners used.

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
17 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS HEADER/SILL SOLUTIONS
JAMSTUD HEADER/SILL ASSEMBLY VALUE


JamStud delivers exceptional value when
utilized as part of a header or sill assembly.
JamStuds unique shape allows for the design
and construction of a lightweight header versus
the more cumbersome built-up header assem-
JamStud @ Sill
blies. Oriented horizontally, JamStud provides
an increased stiffness and strength compared
with standard cee studs, resulting in lighter
headers which require less labor to install.


JamStud Header

The 7/8 d1 dimension of the JamStud


does accommodate a single #10 or
#12 screw (d= 0.19 or 0.216). Proper
installation is desired to center the screw
within the flat width of dimension d1.

JAMSTUD HEADER

TYPICAL BOXED HEADER ASSEMBLIES
Standard
Track Reduces overall materials used Cee Stud
Speeds installation Standard
Fewer fasteners Cee Stud Track

Simple Inspection
JamStud
One Stud Box Two Stud Box
JamStud Header Header Header
* The top track seen in the assemblies above is to capture the cripple studs above and does
not factor in the design of the header.

LOAD TRANSFER TO JAMB


The Steel Networks StiffClip AL series represents an ideal
method to transfer loads from the header or sill to the jamb.
Stiffened ribs add strength, and guide holes are provided for

quick and accurate fastener placement. StiffClip AL is
available in 3-5/8, 6" and 8 depths. See TSNs Light Steel
Framing Connections Catalog for allowable load data.

HIGH-WIND-LOAD HEADERS

In high wind and axial load bearing wall applications, JamStud may be placed inside of a deep-leg track to provide a strong labor-efficient

alternative to four-piece Box headers. While the amount of fasteners remains consistent, use of JamStud reduces material handling by

half to streamline the installation process. Load is effectively transferred to the jambs via TSNs StiffClip HE connectors. With the use

of box headers, Jack Studs are also typically used to support the header vertically. The shelf leg of the StiffClip HE supports the header

vertically to eliminate the use of a Jack Stud. In addition, the StiffClip HE provides web crippling resistance for the header.

JAMSTUD 2-PIECE ASSEMBLY



4-PIECE BOX ASSEMBLY
Deep-Leg
Track Standard
Track


JamStud
Cee Stud

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 18
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS HEADER/SILL DESIGN
DESIGNING JAMSTUD


JamStud Header

1. BASIS FOR TABLES:


The JamStud allowable curtain wall header span tables in this catalog cover the following basic load combination for the
Allowable Stress Design (ASD) Method (IBC2006 and ASCE 7-05):

D + WC&C (Strength determination)

Where WC&C is the Component and Cladding wind load. A sheathing dead load (D) of 12 psf acting vertically on the header is
assumed in the tables.

For the deflection determination, IBC 2003, IBC2006-Sec. 1604.3 and AISI-Wall Stud Design Standard 2004, Sec. B1 allow for a
reduction factor of 0.7 on the Component and Cladding wind load (0.7WC&C).

The JamStud - Allowable Header Span tables are based on the following assumptions:

4-Way distribution of lateral wind pressure acting on the opening


Opening height extends from the floor level to the bottom surface of the header
Header supports the wind pressure from the opening, the wind pressure from half of the distance to floor above,
and the vertical dead load from the sheathing above

The Input for the tables are: the JamStud section, the wall height (ft.), the opening height (ft.) design wind pressure (WC&C, psf),

and the specified deflection limit. The output from the tables includes: the allowable JamStud span or opening width (ft.-in.) and
controlling design factor, deflection or strength ("f" denotes strength, nothing denotes deflection).

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
19 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS HEADER/SILL DESIGN
2. DESIGN EXAMPLE
Service (un-factored) Loads:

Wind Pressure (C&C) = 30 psf


Wall Width = 6.0
Wall Height = 13.0 ft.
Header Span = 9.0 ft.
Opening Height = 10.0 ft.
Specified Deflection Limit = L/360

3. DESIGNING JAMSTUD

Use the Table:



Go to the JamStud - Allowable Header Span table with a 6.0 in. stud member, 30 psf wind load, L/360 deflec-

tion limit, 13.0 ft. wall height and 10.0 ft. opening height. Possible JamStud selections from the table for 9.0 ft.
header span are 600JS250-54 (allowable span = 9 2) and 600JS350-43 (allowable span = 9 5).

Conclusion:
The second option, 600JS350-43, is a lighter section with less mil thickness. Use a 600JS350-43 (with design
thickness = 0.0451 and Fy = 50 ksi).

Important Note:

When ordering the JamStud Header solutions, indicate that the punchouts are not required. Designate JamStud
without punchouts on plans and specify header use when ordering.

4. DESIGN COMPARISON OF HEADER COMPONENTS

JamStud Solution

Typical Built-Up Header
Typical
Design Case
Wall Stud
Section* Shape* Section* Shape*

W = 30 psf
C&C

Wall Width = 6.0 (1) Stud 600S162-54 +


Wall Height = 13.0 (1) Track 600T125-54,
600S162-43 Single 600JS250-54
Header Span = 9.0 attached at 24 o.c. max.
Opening Height = 10.0 horizontally
Deflection Limit = L/360

W = 20 psf
C&C

Wall Width = 3.625 (2) Studs 362S162-68 +


Wall Height = 11.0 (2) Tracks 362T125-68,
362S162-43 Single 362JS350-97
Header Span = 10.0 attached at 24 o.c. max.
Opening Height = 8.0 horizontally
Deflection Limit = L/600

W = 35 psf
C&C

Wall Width = 8.0 (1) Stud 800S162-54 +


Wall Height = 15.0 (1) Track 800T125-54,
800S162-54 Single 800JS250-68
Header Span = 9.5 attached at 24 o.c. max.
Opening Height = 10.0 horizontally
Deflection Limit = L/360

* The runner track for the attachment of the cripple studs was not considered as part of the design cross-section.

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 20
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral pressure
where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 9' 6" f 8' 5" 7' 4" 7' 9" f 7' 4" 6' 2" 7' 3" f 7' 3" f 6' 2" 6' 10" f 6' 10" f 6' 2" 6' 5" f 6' 5" f 6' 2" 5' 11" f 5' 11" f 5' 10"
9
362JS250-33, 50ksi

8 13' 5" f 12' 2" 10' 7" 9' 9" f 9' 6" 8' 3" 8' 11" f 8' 9" 7' 8" 8' 3" f 8' 3" f 7' 3" 7' 10" f 7' 10" f 6' 11" 7' 2" f 7' 2" f 6' 5"
8 9' 5" f 8' 5" 7' 4" 7' 8" f 7' 4" 6' 2" 7' 2" f 7' 2" f 6' 2" 6' 9" f 6' 9" f 6' 2" 6' 5" f 6' 5" f 6' 2" 5' 11" f 5' 11" f 5' 10"
11 10 13' 0" f 12' 2" 10' 7" 9' 8" f 9' 5" 8' 3" 8' 10" f 8' 9" 7' 8" 8' 3" f 8' 3" f 7' 3" 7' 10" f 7' 10" f 6' 11" 7' 2" f 7' 2" f 6' 5"
8 7' 8" f 7' 1" 6' 2" 6' 6" f 6' 2" 5' 3" 6' 1" f 6' 1" f 5' 3" 5' 10" f 5' 10" f 5' 3" 5' 6" f 5' 6" f 5' 3" 5' 1" f 5' 1" f 5' 1" f
13 10 9' 4" f 8' 5" 7' 4" 7' 8" f 7' 4" 6' 2" 7' 2" f 7' 2" f 6' 2" 6' 9" f 6' 9" f 6' 2" 6' 5" f 6' 5" f 6' 2" 5' 11" f 5' 11" f 5' 10"
12 12' 10" f 12' 2" 10' 7" 9' 8" f 9' 5" 8' 3" 8' 10" f 8' 9" 7' 8" 8' 3" f 8' 3" f 7' 3" 7' 10" f 7' 10" f 6' 11" 7' 2" f 7' 2" f 6' 5"
8 6' 7" f 6' 4" 5' 6" 5' 9" f 5' 6" 4' 8" 5' 5" f 5' 5" f 4' 8" 5' 2" f 5' 2" f 4' 8" 4' 11" f 4' 11" f 4' 8" 4' 7" f 4' 7" f 4' 7" f
15 10 7' 8" f 7' 1" 6' 2" 6' 6" f 6' 2" 5' 3" 6' 1" f 6' 1" f 5' 3" 5' 10" f 5' 10" f 5' 3" 5' 6" f 5' 6" f 5' 3" 5' 1" f 5' 1" f 5' 1" f
12 9' 4" f 8' 5" 7' 4" 7' 8" f 7' 4" 6' 2" 7' 2" f 7' 2" f 6' 2" 6' 9" f 6' 9" f 6' 2" 6' 5" f 6' 5" f 6' 2" 6' 0" f 6' 0" f 6' 0" f
6 11' 7" 9' 2" 8' 0" 9' 2" 8' 0" 6' 9" 8' 8" f 8' 0" 6' 9" 8' 1" f 8' 0" 6' 9" 7' 8" f 7' 8" f 6' 9" 7' 0" f 7' 0" f 6' 4"
9
362JS250-43, 50ksi

8 15' 11" f 13' 3" 11' 7" 11' 5" f 10' 5" 9' 0" 10' 4" f 9' 7" 8' 4" 9' 7" f 9' 0" 7' 10" 9' 0" f 8' 7" 7' 6" 8' 2" f 7' 11" 6' 11"
8 11' 6" f 9' 2" 8' 0" 9' 2" f 8' 0" 6' 9" 8' 6" f 8' 0" 6' 9" 7' 11" f 7' 11" f 6' 9" 7' 7" f 7' 7" f 6' 9" 6' 11" f 6' 11" f 6' 4"
11 10 15' 6" f 13' 3" 11' 7" 11' 1" f 10' 3" 9' 0" 10' 2" f 9' 6" 8' 4" 9' 6" f 9' 0" 7' 10" 8' 11" f 8' 7" 7' 6" 8' 2" f 7' 11" 6' 11"
8 9' 5" f 7' 9" 6' 9" 7' 9" 6' 9" 5' 8" 7' 4" f 6' 9" 5' 8" 6' 11" f 6' 9" 5' 8" 6' 7" f 6' 7" f 5' 8" 6' 1" f 6' 1" f 5' 8"
13 10 11' 4" f 9' 2" 8' 0" 9' 1" f 8' 0" 6' 9" 8' 5" f 8' 0" 6' 9" 7' 11" f 7' 11" f 6' 9" 7' 7" f 7' 7" f 6' 9" 6' 11" f 6' 11" f 6' 4"
12 15' 1" f 13' 3" 11' 7" 11' 1" f 10' 3" 9' 0" 10' 2" f 9' 6" 8' 4" 9' 6" f 9' 0" 7' 10" 8' 11" f 8' 7" 7' 6" 8' 2" f 7' 11" 6' 11"
8 8' 2" f 6' 11" 6' 0" 6' 11" f 6' 0" 5' 1" 6' 6" f 6' 0" 5' 1" 6' 2" f 6' 0" 5' 1" 5' 11" f 5' 11" f 5' 1" 5' 5" f 5' 5" f 5' 1"
15 10 9' 5" f 7' 9" 6' 9" 7' 9" 6' 9" 5' 8" 7' 4" f 6' 9" 5' 8" 6' 11" f 6' 9" 5' 8" 6' 7" f 6' 7" f 5' 8" 6' 1" f 6' 1" f 5' 8"
12 11' 4" f 9' 2" 8' 0" 9' 1" f 8' 0" 6' 9" 8' 5" f 8' 0" 6' 9" 7' 11" f 7' 11" f 6' 9" 7' 7" f 7' 7" f 6' 9" 6' 11" f 6' 11" f 6' 4"
6 12' 5" 9' 10" 8' 7" 9' 10" 8' 7" 7' 3" 9' 8" f 8' 7" 7' 3" 9' 1" f 8' 7" 7' 3" 8' 6" f 8' 6" f 7' 3" 7' 9" f 7' 9" f 6' 10"
9
362JS250-54, 50ksi

8 17' 10" f 14' 3" 12' 5" 12' 8" 11' 2" 9' 8" 11' 6" f 10' 3" 8' 11" 10' 7" f 9' 8" 8' 5" 9' 11" f 9' 2" 8' 0" 8' 11" f 8' 6" 7' 5"
8 12' 5" 9' 10" 8' 7" 9' 10" 8' 7" 7' 3" 9' 5" f 8' 7" 7' 3" 8' 10" f 8' 7" 7' 3" 8' 4" f 8' 4" f 7' 3" 7' 8" f 7' 8" f 6' 10"
11 10 17' 4" f 14' 3" 12' 5" 12' 3" f 10' 11" 9' 7" 11' 2" f 10' 2" 8' 10" 10' 4" f 9' 7" 8' 4" 9' 9" f 9' 2" 8' 0" 8' 11" f 8' 6" 7' 5"
8 10' 6" 8' 4" 7' 3" 8' 4" 7' 3" 6' 1" 8' 2" f 7' 3" 6' 1" 7' 8" f 7' 3" 6' 1" 7' 4" f 7' 3" 6' 1" 6' 9" f 6' 9" f 6' 1"
13 10 12' 5" 9' 10" 8' 7" 9' 10" 8' 7" 7' 3" 9' 4" f 8' 7" 7' 3" 8' 9" f 8' 7" 7' 3" 8' 4" f 8' 4" f 7' 3" 7' 8" f 7' 8" f 6' 10"
12 16' 10" f 14' 3" 12' 5" 12' 1" f 10' 11" 9' 7" 11' 1" f 10' 2" 8' 10" 10' 4" f 9' 7" 8' 4" 9' 9" f 9' 1" 8' 0" 8' 11" f 8' 6" 7' 5"
8 9' 2" f 7' 5" 6' 6" 7' 5" 6' 6" 5' 6" 7' 3" f 6' 6" 5' 6" 6' 11" f 6' 6" 5' 6" 6' 7" f 6' 6" 5' 6" 6' 1" f 6' 1" f 5' 6"
15 10 10' 6" f 8' 4" 7' 3" 8' 4" 7' 3" 6' 1" 8' 2" f 7' 3" 6' 1" 7' 8" f 7' 3" 6' 1" 7' 4" f 7' 3" 6' 1" 6' 9" f 6' 9" f 6' 1"
12 12' 5" 9' 10" 8' 7" 9' 10" 8' 7" 7' 3" 9' 4" f 8' 7" 7' 3" 8' 9" f 8' 7" 7' 3" 8' 4" f 8' 4" f 7' 3" 7' 8" f 7' 8" f 6' 10"
6 13' 4" 10' 7" 9' 3" 10' 7" 9' 3" 7' 10" 10' 7" 9' 3" 7' 10" 10' 3" f 9' 3" 7' 10" 9' 8" f 9' 3" 7' 10" 8' 9" f 8' 6" 7' 3"
9
362JS250-68, 50ksi

8 19' 4" 15' 4" 13' 4" 13' 6" 11' 11" 10' 3" 12' 4" 10' 11" 9' 5" 11' 7" 10' 3" 8' 11" 10' 11" 9' 9" 8' 5" 9' 11" f 9' 0" 7' 10"
8 13' 4" 10' 7" 9' 3" 10' 7" 9' 3" 7' 10" 10' 7" f 9' 3" 7' 10" 9' 10" f 9' 3" 7' 10" 9' 4" f 9' 1" 7' 10" 8' 6" f 8' 4" 7' 3"
11 10 19' 4" 15' 4" 13' 4" 13' 0" 11' 7" 10' 1" 12' 0" 10' 9" 9' 5" 11' 3" 10' 1" 8' 10" 10' 9" f 9' 8" 8' 5" 9' 9" f 8' 11" 7' 10"
8 11' 3" 8' 11" 7' 10" 8' 11" 7' 10" 6' 7" 8' 11" 7' 10" 6' 7" 8' 7" f 7' 10" 6' 7" 8' 2" f 7' 10" 6' 7" 7' 6" f 7' 6" f 6' 7"
13 10 13' 4" 10' 7" 9' 3" 10' 7" 9' 3" 7' 10" 10' 5" f 9' 3" 7' 10" 9' 9" f 9' 3" 7' 10" 9' 3" f 9' 0" 7' 10" 8' 6" f 8' 4" 7' 3"
12 18' 11" f 15' 4" 13' 4" 12' 10" 11' 6" 10' 1" 11' 11" 10' 9" 9' 5" 11' 3" 10' 1" 8' 10" 10' 9" f 9' 8" 8' 5" 9' 9" f 8' 11" 7' 10"
8 10' 1" 8' 0" 7' 0" 8' 0" 7' 0" 5' 10" 8' 0" 7' 0" 5' 10" 7' 9" f 7' 0" 5' 10" 7' 4" f 7' 0" 5' 10" 6' 9" f 6' 9" f 5' 10"
15 10 11' 3" 8' 11" 7' 10" 8' 11" 7' 10" 6' 7" 8' 11" 7' 10" 6' 7" 8' 7" f 7' 10" 6' 7" 8' 2" f 7' 10" 6' 7" 7' 6" f 7' 6" f 6' 7"
12 13' 4" 10' 7" 9' 3" 10' 7" 9' 3" 7' 10" 10' 5" f 9' 3" 7' 10" 9' 9" f 9' 3" 7' 10" 9' 3" f 9' 0" 7' 10" 8' 6" f 8' 4" 7' 3"

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
21 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 14' 11" 11' 10" 10' 4" 11' 10" 10' 4" 8' 8" 11' 10" 10' 4" 8' 8" 11' 10" 10' 4" 8' 8" 11' 8" 10' 3" 8' 8" 10' 8" 9' 5" 8' 0"
9
362JS250-97, 50ksi

8 21' 6" 17' 1" 14' 11" 14' 11" 13' 2" 11' 3" 13' 8" 12' 1" 10' 4" 12' 9" 11' 3" 9' 9" 12' 1" 10' 8" 9' 3" 11' 1" 9' 10" 8' 6"
8 14' 11" 11' 10" 10' 4" 11' 10" 10' 4" 8' 8" 11' 10" 10' 4" 8' 8" 11' 10" 10' 4" 8' 8" 11' 3" 9' 11" 8' 7" 10' 4" f 9' 2" 7' 11"
11 10 21' 6" 17' 1" 14' 11" 14' 4" 12' 9" 11' 0" 13' 2" 11' 9" 10' 2" 12' 4" 11' 0" 9' 8" 11' 9" 10' 6" 9' 2" 10' 10" 9' 9" 8' 6"
8 12' 7" 10' 0" 8' 8" 10' 0" 8' 8" 7' 4" 10' 0" 8' 8" 7' 4" 10' 0" 8' 8" 7' 4" 9' 11" f 8' 8" 7' 4" 9' 2" f 8' 7" 7' 4"
13 10 14' 11" 11' 10" 10' 4" 11' 10" 10' 4" 8' 8" 11' 10" 10' 4" 8' 8" 11' 7" 10' 4" 8' 8" 11' 0" 9' 10" 8' 7" 10' 2" f 9' 1" 7' 11"
12 21' 5" 17' 1" 14' 11" 14' 0" 12' 7" 11' 0" 12' 11" 11' 8" 10' 2" 12' 3" 11' 0" 9' 8" 11' 8" 10' 6" 9' 2" 10' 10" 9' 9" 8' 6"
8 11' 3" 8' 11" 7' 9" 8' 11" 7' 9" 6' 7" 8' 11" 7' 9" 6' 7" 8' 11" 7' 9" 6' 7" 8' 11" f 7' 9" 6' 7" 8' 3" f 7' 9" 6' 7"
15 10 12' 7" 10' 0" 8' 8" 10' 0" 8' 8" 7' 4" 10' 0" 8' 8" 7' 4" 10' 0" 8' 8" 7' 4" 9' 10" f 8' 8" 7' 4" 9' 1" f 8' 7" 7' 4"
12 14' 11" 11' 10" 10' 4" 11' 10" 10' 4" 8' 8" 11' 10" 10' 4" 8' 8" 11' 7" 10' 4" 8' 8" 11' 0" 9' 10" 8' 7" 10' 2" f 9' 1" 7' 11"
6 17' 6" 13' 11" 12' 2" 13' 1" f 12' 0" 10' 3" 11' 11" f 11' 2" 9' 6" 11' 2" f 10' 5" 8' 10" 10' 5" f 9' 10" 8' 5" 9' 4" f 9' 0" 7' 8"
9
362JS350-68, 50ksi

8 22' 2" 17' 7" 15' 10" 14' 3" 12' 7" 10' 10" 13' 1" 11' 6" 9' 11" 12' 2" 10' 10" 9' 4" 11' 6" 10' 3" 8' 10" 10' 4" f 9' 5" 8' 2"
8 17' 0" f 13' 11" 12' 2" 12' 8" f 11' 9" 10' 1" 11' 6" f 10' 9" 9' 3" 10' 8" f 10' 1" 8' 8" 10' 0" f 9' 6" 8' 3" 9' 0" f 8' 9" 7' 7"
11 10 20' 9" 17' 2" 15' 2" 13' 9" 12' 2" 10' 7" 12' 7" 11' 3" 9' 10" 11' 10" 10' 7" 9' 3" 11' 2" f 10' 1" 8' 10" 10' 1" f 9' 4" 8' 2"
8 14' 4" f 11' 9" 10' 3" 11' 0" f 10' 3" 8' 8" 10' 1" f 10' 1" f 8' 8" 9' 5" f 9' 5" f 8' 2" 8' 11" f 8' 11" f 7' 9" 8' 1" f 8' 1" f 7' 1"

13 10 16' 8" f 13' 11" 12' 2" 12' 3" f 11' 6" 9' 11" 11' 3" f 10' 7" 9' 2" 10' 5" f 9' 11" 8' 8" 9' 10" f 9' 6" 8' 3" 9' 0" f 8' 9" 7' 7"
12 20' 6" 16' 7" 14' 9" 13' 6" 12' 1" 10' 7" 12' 6" 11' 3" 9' 10" 11' 9" 10' 7" 9' 3" 11' 2" f 10' 1" 8' 10" 10' 1" f 9' 5" 8' 2"
8 12' 6" f 10' 6" 9' 2" 9' 11" f 9' 2" 7' 8" 9' 2" f 9' 2" f 7' 8" 8' 7" f 8' 7" f 7' 8" 8' 1" f 8' 1" f 7' 4" 7' 4" f 7' 4" f 6' 9"

15 10 14' 1" f 11' 9" 10' 3" 10' 10" f 10' 3" 8' 8" 10' 0" f 10' 0" f 8' 8" 9' 4" f 9' 4" f 8' 2" 8' 10" f 8' 10" f 7' 9" 8' 1" f 8' 1" f 7' 1"
12 16' 4" f 13' 11" 12' 2" 12' 2" f 11' 5" 9' 11" 11' 2" f 10' 7" 9' 2" 10' 5" f 9' 11" 8' 8" 9' 10" f 9' 6" 8' 3" 9' 0" f 8' 9" 7' 7"
6 19' 7" 15' 6" 13' 7" 15' 6" 13' 7" 11' 5" 14' 2" 12' 5" 10' 9" 13' 2" 11' 9" 10' 0" 12' 5" 11' 1" 9' 5" 11' 5" f 10' 2" 8' 8"
9
362JS350-97, 50ksi

8 25' 2" 20' 0" 17' 6" 15' 11" 14' 2" 12' 1" 14' 8" 13' 0" 11' 1" 13' 9" 12' 1" 10' 5" 13' 0" 11' 6" 9' 11" 11' 11" 10' 6" 9' 1"
8 19' 7" 15' 6" 13' 7" 15' 0" 13' 3" 11' 3" 13' 8" 12' 1" 10' 4" 12' 9" 11' 3" 9' 8" 12' 1" f 10' 8" 9' 2" 10' 10" f 9' 10" 8' 6"
11 10 23' 7" 19' 4" 17' 1" 15' 5" 13' 8" 11' 9" 14' 1" 12' 7" 10' 11" 13' 3" 11' 9" 10' 3" 12' 7" 11' 2" 9' 9" 11' 7" 10' 4" 9' 1"
8 16' 6" 13' 1" 11' 5" 13' 1" 11' 5" 9' 8" 12' 3" f 11' 5" 9' 8" 11' 5" f 10' 8" 9' 1" 10' 8" f 10' 1" 8' 8" 9' 8" f 9' 3" 7' 11"

13 10 19' 7" 15' 6" 13' 7" 14' 6" 12' 10" 11' 1" 13' 4" 11' 10" 10' 3" 12' 5" 11' 1" 9' 7" 11' 8" f 10' 6" 9' 2" 10' 7" f 9' 9" 8' 5"
12 23' 1" 18' 8" 16' 6" 15' 0" 13' 5" 11' 8" 13' 10" 12' 5" 10' 10" 13' 0" 11' 8" 10' 3" 12' 5" 11' 2" 9' 9" 11' 6" 10' 4" 9' 1"
8 14' 9" 11' 8" 10' 3" 11' 8" 10' 3" 8' 7" 11' 0" f 10' 3" 8' 7" 10' 4" f 10' 1" 8' 7" 9' 9" f 9' 7" 8' 3" 8' 10" f 8' 9" 7' 7"

15 10 16' 6" 13' 1" 11' 5" 13' 0" f 11' 5" 9' 8" 12' 0" f 11' 3" 9' 8" 11' 2" f 10' 6" 9' 1" 10' 6" f 10' 0" 8' 8" 9' 7" f 9' 2" 7' 11"
12 19' 7" 15' 6" 13' 7" 14' 3" 12' 8" 11' 1" 13' 1" 11' 9" 10' 3" 12' 4" f 11' 1" 9' 7" 11' 7" f 10' 6" 9' 2" 10' 7" f 9' 9" 8' 5"
6 20' 10" 16' 6" 14' 5" 16' 6" 14' 5" 12' 2" 15' 1" 13' 2" 11' 5" 14' 0" 12' 3" 10' 7" 13' 2" 11' 9" 10' 0" 12' 0" 10' 9" 9' 2"
362JS350-118, 50ksi

9 8 26' 10" 21' 4" 18' 7" 16' 8" 15' 0" 12' 10" 15' 7" 13' 9" 11' 9" 14' 7" 12' 10" 11' 0" 13' 9" 12' 2" 10' 5" 12' 7" 11' 2" 9' 7"
8 20' 10" 16' 6" 14' 5" 15' 11" 14' 0" 12' 0" 14' 7" 12' 10" 11' 0" 13' 7" 12' 0" 10' 3" 12' 10" 11' 4" 9' 9" 11' 9" 10' 5" 8' 11"
11 10 25' 1" 19' 11" 18' 1" 16' 4" 14' 5" 12' 5" 14' 11" 13' 3" 11' 6" 14' 0" 12' 5" 10' 9" 13' 3" 11' 10" 10' 3" 12' 2" 10' 11" 9' 6"
8 17' 7" 13' 11" 12' 2" 13' 11" 12' 2" 10' 3" 13' 8" f 12' 1" 10' 3" 12' 9" f 11' 3" 9' 8" 12' 0" f 10' 8" 9' 2" 10' 10" f 9' 9" 8' 5"

13 10 20' 10" 16' 6" 14' 5" 15' 4" 13' 7" 11' 8" 14' 1" 12' 6" 10' 9" 13' 2" 11' 8" 10' 2" 12' 6" 11' 1" 9' 8" 11' 6" 10' 3" 8' 11"
12 23' 11" 19' 9" 17' 6" 15' 10" 14' 1" 12' 4" 14' 7" 13' 1" 11' 5" 13' 9" 12' 4" 10' 9" 13' 1" 11' 9" 10' 3" 12' 1" 10' 11" 9' 6"
8 15' 8" 12' 5" 10' 10" 12' 5" 10' 10" 9' 2" 12' 4" f 10' 10" 9' 2" 11' 6" f 10' 9" 9' 2" 10' 11" f 10' 2" 8' 8" 9' 11" f 9' 4" 8' 0"

15 10 17' 7" 13' 11" 12' 2" 13' 11" 12' 2" 10' 3" 13' 4" f 11' 10" 10' 3" 12' 5" f 11' 1" 9' 7" 11' 9" f 10' 6" 9' 1" 10' 8" f 9' 8" 8' 5"
12 20' 10" 16' 6" 14' 5" 15' 0" 13' 5" 11' 8" 13' 10" 12' 4" 10' 9" 13' 0" 11' 8" 10' 2" 12' 4" 11' 1" 9' 8" 11' 5" 10' 3" 8' 11"

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 22
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 9' 9" f 8' 6" 7' 5" 8' 1" f 7' 5" 6' 3" 7' 6" f 7' 5" 6' 3" 7' 1" f 7' 1" f 6' 3" 6' 9" f 6' 9" f 6' 3" 6' 2" f 6' 2" f 6' 2" f
9
400JS250-33, 50ksi

8 13' 10" f 12' 4" 10' 9" 10' 2" f 10' 2" f 8' 10" 9' 3" f 9' 3" f 8' 2" 8' 8" f 8' 8" f 7' 8" 8' 2" f 8' 2" f 7' 4" 7' 6" f 7' 6" f 6' 9"
8 9' 7" f 8' 6" 7' 5" 7' 11" f 7' 5" 6' 3" 7' 5" f 7' 5" f 6' 3" 7' 0" f 7' 0" f 6' 3" 6' 8" f 6' 8" f 6' 3" 6' 2" f 6' 2" f 6' 2" f
11 10 13' 5" f 12' 4" 10' 9" 10' 0" f 10' 0" f 8' 9" 9' 3" f 9' 3" f 8' 2" 8' 8" f 8' 8" f 7' 8" 8' 2" f 8' 2" f 7' 4" 7' 6" f 7' 6" f 6' 9"
8 7' 10" f 7' 2" 6' 3" 6' 8" f 6' 3" 5' 3" 6' 4" f 6' 3" 5' 3" 6' 0" f 6' 0" f 5' 3" 5' 9" f 5' 9" f 5' 3" 5' 4" f 5' 4" f 5' 3"

13 10 9' 7" f 8' 6" 7' 5" 7' 11" f 7' 5" 6' 3" 7' 5" f 7' 5" f 6' 3" 7' 0" f 7' 0" f 6' 3" 6' 8" f 6' 8" f 6' 3" 6' 2" f 6' 2" f 6' 2" f
12 13' 3" f 12' 4" 10' 9" 10' 0" f 10' 0" f 8' 9" 9' 3" f 9' 3" f 8' 2" 8' 8" f 8' 8" f 7' 8" 8' 2" f 8' 2" f 7' 4" 7' 6" f 7' 6" f 6' 9"
8 6' 9" f 6' 5" 5' 7" 5' 10" f 5' 7" 4' 9" 5' 7" f 5' 7" f 4' 9" 5' 4" f 5' 4" f 4' 9" 5' 1" f 5' 1" f 4' 9" 4' 9" f 4' 9" f 4' 9" f

15 10 7' 10" f 7' 2" 6' 3" 6' 8" f 6' 3" 5' 3" 6' 4" f 6' 3" 5' 3" 6' 0" f 6' 0" f 5' 3" 5' 9" f 5' 9" f 5' 3" 5' 4" f 5' 4" f 5' 3"
12 9' 7" f 8' 6" 7' 5" 7' 11" f 7' 5" 6' 3" 7' 5" f 7' 5" f 6' 3" 7' 0" f 7' 0" f 6' 3" 6' 8" f 6' 8" f 6' 3" 6' 2" f 6' 2" f 6' 2" f
6 11' 9" 9' 3" 8' 1" 9' 3" 8' 1" 6' 10" 9' 0" f 8' 1" 6' 10" 8' 5" f 8' 1" 6' 10" 8' 0" f 8' 0" f 6' 10" 7' 3" f 7' 3" f 6' 9"
9
400JS250-43, 50ksi

8 16' 6" f 13' 5" 11' 9" 12' 0" f 11' 1" 9' 7" 10' 10" f 10' 3" 8' 10" 10' 1" f 9' 7" 8' 4" 9' 5" f 9' 1" 7' 11" 8' 6" f 8' 5" 7' 4"
8 11' 9" f 9' 3" 8' 1" 9' 3" 8' 1" 6' 10" 8' 9" f 8' 1" 6' 10" 8' 3" f 8' 1" 6' 10" 7' 10" f 7' 10" f 6' 10" 7' 3" f 7' 3" f 6' 9"
11 10 16' 1" f 13' 5" 11' 9" 11' 7" f 10' 11" 9' 6" 10' 7" f 10' 1" 8' 10" 9' 11" f 9' 6" 8' 4" 9' 4" f 9' 1" 7' 11" 8' 6" f 8' 5" 7' 4"
8 9' 7" f 7' 10" 6' 10" 7' 10" 6' 10" 5' 9" 7' 7" f 6' 10" 5' 9" 7' 2" f 6' 10" 5' 9" 6' 10" f 6' 10" f 5' 9" 6' 4" f 6' 4" f 5' 9"
13 10 11' 8" f 9' 3" 8' 1" 9' 3" 8' 1" 6' 10" 8' 9" f 8' 1" 6' 10" 8' 3" f 8' 1" 6' 10" 7' 10" f 7' 10" f 6' 10" 7' 3" f 7' 3" f 6' 9"
12 15' 8" f 13' 5" 11' 9" 11' 6" f 10' 10" 9' 6" 10' 7" f 10' 1" 8' 10" 9' 11" f 9' 6" 8' 4" 9' 4" f 9' 1" 7' 11" 8' 6" f 8' 5" 7' 4"
8 8' 4" f 7' 0" 6' 1" 7' 0" 6' 1" 5' 2" 6' 9" f 6' 1" 5' 2" 6' 5" f 6' 1" 5' 2" 6' 1" f 6' 1" f 5' 2" 5' 8" f 5' 8" f 5' 2"
15 10 9' 7" f 7' 10" 6' 10" 7' 10" 6' 10" 5' 9" 7' 7" f 6' 10" 5' 9" 7' 2" f 6' 10" 5' 9" 6' 10" f 6' 10" f 5' 9" 6' 4" f 6' 4" f 5' 9"
12 11' 7" f 9' 3" 8' 1" 9' 3" 8' 1" 6' 10" 8' 9" f 8' 1" 6' 10" 8' 3" f 8' 1" 6' 10" 7' 10" f 7' 10" f 6' 10" 7' 3" f 7' 3" f 6' 9"
6 12' 7" 10' 0" 8' 9" 10' 0" 8' 9" 7' 4" 10' 0" 8' 9" 7' 4" 9' 5" f 8' 9" 7' 4" 8' 11" f 8' 9" 7' 4" 8' 1" f 8' 1" f 7' 4"
9
400JS250-54, 50ksi

8 18' 2" 14' 5" 12' 7" 13' 4" f 12' 0" 10' 4" 12' 1" f 11' 0" 9' 6" 11' 1" f 10' 4" 8' 11" 10' 5" f 9' 9" 8' 6" 9' 4" f 9' 0" 7' 10"
8 12' 7" 10' 0" 8' 9" 10' 0" 8' 9" 7' 4" 9' 9" f 8' 9" 7' 4" 9' 2" f 8' 9" 7' 4" 8' 8" f 8' 8" f 7' 4" 7' 11" f 7' 11" f 7' 3"
11 10 18' 1" f 14' 5" 12' 7" 12' 10" f 11' 8" 10' 2" 11' 8" f 10' 9" 9' 5" 10' 10" f 10' 2" 8' 11" 10' 2" f 9' 8" 8' 6" 9' 3" f 9' 0" 7' 10"
8 10' 7" 8' 5" 7' 4" 8' 5" 7' 4" 6' 2" 8' 5" f 7' 4" 6' 2" 8' 0" f 7' 4" 6' 2" 7' 7" f 7' 4" 6' 2" 7' 0" f 7' 0" f 6' 2"
13 10 12' 7" 10' 0" 8' 9" 10' 0" 8' 9" 7' 4" 9' 8" f 8' 9" 7' 4" 9' 1" f 8' 9" 7' 4" 8' 8" f 8' 8" f 7' 4" 7' 11" f 7' 11" f 7' 3"
12 17' 6" f 14' 5" 12' 7" 12' 7" f 11' 7" 10' 2" 11' 6" f 10' 9" 9' 5" 10' 9" f 10' 2" 8' 11" 10' 2" f 9' 8" 8' 6" 9' 3" f 9' 0" 7' 10"
8 9' 4" f 7' 6" 6' 7" 7' 6" 6' 7" 5' 6" 7' 6" f 6' 7" 5' 6" 7' 2" f 6' 7" 5' 6" 6' 10" f 6' 7" 5' 6" 6' 4" f 6' 4" f 5' 6"
15 10 10' 7" 8' 5" 7' 4" 8' 5" 7' 4" 6' 2" 8' 5" f 7' 4" 6' 2" 8' 0" f 7' 4" 6' 2" 7' 7" f 7' 4" 6' 2" 7' 0" f 7' 0" f 6' 2"
12 12' 7" 10' 0" 8' 9" 10' 0" 8' 9" 7' 4" 9' 8" f 8' 9" 7' 4" 9' 1" f 8' 9" 7' 4" 8' 8" f 8' 8" f 7' 4" 7' 11" f 7' 11" f 7' 3"
6 13' 7" 10' 9" 9' 5" 10' 9" 9' 5" 7' 11" 10' 9" 9' 5" 7' 11" 10' 8" f 9' 5" 7' 11" 10' 1" f 9' 5" 7' 11" 9' 2" f 9' 1" 7' 10"
9
400JS250-68, 50ksi

8 19' 7" 15' 6" 13' 7" 14' 6" 12' 9" 11' 0" 13' 3" 11' 9" 10' 1" 12' 5" 11' 0" 9' 6" 11' 8" f 10' 5" 9' 0" 10' 5" f 9' 7" 8' 4"
8 13' 7" 10' 9" 9' 5" 10' 9" 9' 5" 7' 11" 10' 9" 9' 5" 7' 11" 10' 3" f 9' 5" 7' 11" 9' 8" f 9' 5" 7' 11" 8' 10" f 8' 10" f 7' 8"
11 10 19' 7" 15' 6" 13' 7" 13' 11" 12' 5" 10' 9" 12' 10" 11' 5" 9' 11" 12' 0" f 10' 9" 9' 5" 11' 3" f 10' 3" 9' 0" 10' 2" f 9' 6" 8' 4"
8 11' 5" 9' 1" 7' 11" 9' 1" 7' 11" 6' 8" 9' 1" 7' 11" 6' 8" 8' 11" f 7' 11" 6' 8" 8' 6" f 7' 11" 6' 8" 7' 10" f 7' 10" f 6' 8"
13 10 13' 7" 10' 9" 9' 5" 10' 9" 9' 5" 7' 11" 10' 9" f 9' 5" 7' 11" 10' 2" f 9' 5" 7' 11" 9' 7" f 9' 5" 7' 11" 8' 10" f 8' 10" f 7' 8"
12 19' 7" 15' 6" 13' 7" 13' 8" 12' 3" 10' 9" 12' 8" 11' 4" 9' 11" 11' 10" f 10' 9" 9' 5" 11' 2" f 10' 3" 9' 0" 10' 2" f 9' 6" 8' 4"
8 10' 2" 8' 1" 7' 1" 8' 1" 7' 1" 5' 11" 8' 1" 7' 1" 5' 11" 8' 0" f 7' 1" 5' 11" 7' 8" f 7' 1" 5' 11" 7' 1" f 7' 1" f 5' 11"
15 10 11' 5" 9' 1" 7' 11" 9' 1" 7' 11" 6' 8" 9' 1" 7' 11" 6' 8" 8' 11" f 7' 11" 6' 8" 8' 6" f 7' 11" 6' 8" 7' 10" f 7' 10" f 6' 8"
12 13' 7" 10' 9" 9' 5" 10' 9" 9' 5" 7' 11" 10' 9" f 9' 5" 7' 11" 10' 2" f 9' 5" 7' 11" 9' 7" f 9' 5" 7' 11" 8' 10" f 8' 10" f 7' 8"

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
23 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 15' 1" 12' 0" 10' 5" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 11' 4" f 10' 1" 8' 7"
9
400JS250-97, 50ksi

8 21' 10" 17' 3" 15' 1" 15' 11" 14' 1" 12' 1" 14' 8" 12' 11" 11' 1" 13' 8" 12' 1" 10' 5" 12' 11" 11' 5" 9' 10" 11' 10" 10' 6" 9' 1"
8 15' 1" 12' 0" 10' 5" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 11' 11" f 10' 5" 8' 10" 10' 10" f 9' 9" 8' 5"
11 10 21' 10" 17' 3" 15' 1" 15' 4" 13' 7" 11' 9" 14' 1" 12' 6" 10' 10" 13' 2" 11' 9" 10' 3" 12' 6" 11' 2" 9' 9" 11' 6" 10' 4" 9' 1"
8 12' 9" 10' 1" 8' 10" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 9' 6" f 8' 10" 7' 5"
13 10 15' 1" 12' 0" 10' 5" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 11' 7" f 10' 5" 8' 10" 10' 7" f 9' 8" 8' 5"
12 21' 10" 17' 3" 15' 1" 14' 11" 13' 4" 11' 8" 13' 9" 12' 4" 10' 10" 13' 0" 11' 8" 10' 3" 12' 4" 11' 2" 9' 9" 11' 6" 10' 4" 9' 1"
8 11' 4" 9' 0" 7' 10" 9' 0" 7' 10" 6' 8" 9' 0" 7' 10" 6' 8" 9' 0" 7' 10" 6' 8" 9' 0" 7' 10" 6' 8" 8' 7" f 7' 10" 6' 8"
15 10 12' 9" 10' 1" 8' 10" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 9' 6" f 8' 10" 7' 5"
12 15' 1" 12' 0" 10' 5" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 12' 0" 10' 5" 8' 10" 11' 6" f 10' 5" 8' 10" 10' 7" f 9' 8" 8' 5"
6 13' 2" f 12' 2" 10' 7" 10' 4" f 10' 4" f 8' 11" 9' 6" f 9' 6" f 8' 9" 8' 10" f 8' 10" f 8' 2" 8' 4" f 8' 4" f 7' 9" 7' 7" f 7' 7" f 7' 1"
9
400JS350-43, 50ksi

8 17' 7" f 16' 1" 14' 6" 12' 5" f 11' 7" 10' 0" 11' 2" f 10' 8" 9' 2" 10' 3" f 10' 0" 8' 8" 9' 7" f 9' 6" 8' 3" 8' 8" f 8' 8" f 7' 8"
8 12' 11" f 12' 2" 10' 7" 10' 0" f 10' 0" f 8' 11" 9' 3" f 9' 3" f 8' 7" 8' 7" f 8' 7" f 8' 0" 8' 2" f 8' 2" f 7' 8" 7' 5" f 7' 5" f 7' 0"
11 10 17' 1" f 15' 9" 14' 0" 11' 11" f 11' 4" 9' 10" 10' 10" f 10' 6" 9' 2" 10' 1" f 9' 10" 8' 8" 9' 6" f 9' 5" 8' 3" 8' 8" f 8' 8" f 7' 8"
8 10' 8" f 10' 3" 8' 11" 8' 8" f 8' 8" f 7' 6" 8' 0" f 8' 0" f 7' 6" 7' 7" f 7' 7" f 7' 6" 7' 2" f 7' 2" f 7' 2" f 6' 7" f 6' 7" f 6' 7" f
13 10 12' 9" f 12' 2" 10' 7" 9' 11" f 9' 11" f 8' 11" 9' 2" f 9' 2" f 8' 6" 8' 7" f 8' 7" f 8' 0" 8' 2" f 8' 2" f 7' 8" 7' 5" f 7' 5" f 7' 1"
12 16' 6" f 15' 4" 13' 8" 11' 10" f 11' 3" 9' 10" 10' 10" f 10' 6" 9' 2" 10' 1" f 9' 10" 8' 8" 9' 6" f 9' 5" 8' 3" 8' 8" f 8' 8" f 7' 8"
8 9' 3" f 9' 2" 8' 0" 7' 8" f 7' 8" f 6' 9" 7' 2" f 7' 2" f 6' 9" 6' 10" f 6' 10" f 6' 9" 6' 6" f 6' 6" f 6' 6" f 5' 11" f 5' 11" f 5' 11" f
15 10 10' 7" f 10' 3" 8' 11" 8' 7" f 8' 7" f 7' 6" 8' 0" f 8' 0" f 7' 6" 7' 7" f 7' 7" f 7' 6" 7' 2" f 7' 2" f 7' 2" f 6' 7" f 6' 7" f 6' 7" f
12 12' 7" f 12' 2" 10' 7" 9' 11" f 9' 11" f 8' 11" 9' 2" f 9' 2" f 8' 6" 8' 7" f 8' 7" f 8' 0" 8' 2" f 8' 2" f 7' 8" 7' 5" f 7' 5" f 7' 1"
6 16' 0" f 13' 1" 11' 5" 12' 0" f 11' 5" 9' 8" 11' 1" f 11' 1" f 9' 5" 10' 3" f 10' 3" f 8' 9" 9' 7" f 9' 7" f 8' 4" 8' 8" f 8' 8" f 7' 7"
9
400JS350-54, 50ksi

8 20' 9" f 17' 5" 15' 8" 14' 1" 12' 6" 10' 8" 12' 8" f 11' 5" 9' 10" 11' 7" f 10' 8" 9' 3" 10' 10" f 10' 2" 8' 10" 9' 8" f 9' 4" 8' 2"
8 15' 7" f 13' 1" 11' 5" 11' 8" f 11' 5" 9' 8" 10' 7" f 10' 7" f 9' 2" 9' 10" f 9' 10" f 8' 7" 9' 3" f 9' 3" f 8' 2" 8' 5" f 8' 5" f 7' 6"
11 10 19' 11" f 17' 0" 15' 0" 13' 6" f 12' 1" 10' 6" 12' 2" f 11' 2" 9' 9" 11' 3" f 10' 6" 9' 2" 10' 6" f 10' 0" 8' 9" 9' 7" f 9' 4" 8' 2"
8 12' 11" f 11' 0" 9' 8" 10' 1" f 9' 8" 8' 1" 9' 4" f 9' 4" f 8' 1" 8' 9" f 8' 9" f 8' 1" 8' 3" f 8' 3" f 7' 8" 7' 6" f 7' 6" f 7' 1"
13 10 15' 2" f 13' 1" 11' 5" 11' 5" f 11' 5" f 9' 8" 10' 5" f 10' 5" f 9' 2" 9' 9" f 9' 9" f 8' 7" 9' 3" f 9' 3" f 8' 2" 8' 5" f 8' 5" f 7' 6"
12 19' 2" f 16' 6" 14' 8" 13' 2" f 12' 0" 10' 6" 12' 0" f 11' 2" 9' 9" 11' 2" f 10' 6" 9' 2" 10' 6" f 10' 0" 8' 9" 9' 7" f 9' 4" 8' 2"
8 11' 3" f 9' 10" 8' 7" 9' 1" f 8' 7" 7' 3" 8' 5" f 8' 5" f 7' 3" 7' 11" f 7' 11" f 7' 3" 7' 6" f 7' 6" f 7' 3" 6' 10" f 6' 10" f 6' 8"
15 10 12' 9" f 11' 0" 9' 8" 10' 0" f 9' 8" 8' 1" 9' 3" f 9' 3" f 8' 1" 8' 8" f 8' 8" f 8' 1" 8' 3" f 8' 3" f 7' 8" 7' 6" f 7' 6" f 7' 1"
12 14' 11" f 13' 1" 11' 5" 11' 4" f 11' 4" f 9' 8" 10' 5" f 10' 5" f 9' 1" 9' 9" f 9' 9" f 8' 7" 9' 3" f 9' 3" f 8' 2" 8' 5" f 8' 5" f 7' 6"
6 17' 9" 14' 1" 12' 4" 13' 9" f 12' 4" 10' 4" 12' 5" f 11' 11" 10' 2" 11' 8" f 11' 2" 9' 6" 10' 11" f 10' 6" 9' 0" 9' 10" f 9' 7" 8' 3"
9
400JS350-68, 50ksi

8 23' 9" f 18' 11" 16' 6" 15' 3" 13' 6" 11' 6" 14' 0" 12' 4" 10' 7" 13' 0" 11' 6" 9' 11" 12' 3" f 10' 11" 9' 5" 10' 11" f 10' 1" 8' 8"
8 17' 6" f 14' 1" 12' 4" 13' 3" f 12' 4" 10' 4" 12' 0" f 11' 6" 9' 10" 11' 2" f 10' 9" 9' 3" 10' 5" f 10' 2" 8' 9" 9' 5" f 9' 4" 8' 1"
11 10 22' 3" f 18' 4" 16' 2" 14' 8" 13' 0" 11' 3" 13' 5" 12' 0" 10' 5" 12' 6" f 11' 3" 9' 10" 11' 9" f 10' 9" 9' 4" 10' 7" f 9' 11" 8' 8"
8 14' 8" f 11' 10" 10' 4" 11' 6" f 10' 4" 8' 9" 10' 6" f 10' 4" 8' 9" 9' 10" f 9' 10" f 8' 8" 9' 3" f 9' 3" f 8' 3" 8' 5" f 8' 5" f 7' 7"
13 10 17' 3" f 14' 1" 12' 4" 12' 10" f 12' 3" 10' 4" 11' 8" f 11' 3" 9' 9" 10' 11" f 10' 7" 9' 2" 10' 3" f 10' 1" 8' 9" 9' 4" f 9' 4" f 8' 1"
12 21' 8" f 17' 9" 15' 9" 14' 4" 12' 10" 11' 3" 13' 3" 11' 10" 10' 5" 12' 4" f 11' 3" 9' 10" 11' 7" f 10' 8" 9' 4" 10' 7" f 9' 11" 8' 8"
8 12' 10" f 10' 7" 9' 3" 10' 3" f 9' 3" 7' 10" 9' 6" f 9' 3" 7' 10" 8' 11" f 8' 11" f 7' 10" 8' 5" f 8' 5" f 7' 10" 7' 8" f 7' 8" f 7' 2"
15 10 14' 5" f 11' 10" 10' 4" 11' 3" f 10' 4" 8' 9" 10' 5" f 10' 4" 8' 9" 9' 9" f 9' 9" f 8' 8" 9' 3" f 9' 3" f 8' 3" 8' 5" f 8' 5" f 7' 7"
12 16' 11" f 14' 1" 12' 4" 12' 8" f 12' 2" 10' 4" 11' 7" f 11' 3" 9' 9" 10' 10" f 10' 7" 9' 2" 10' 3" f 10' 1" 8' 9" 9' 4" f 9' 4" f 8' 1"

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 24
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 19' 10" 15' 9" 13' 9" 15' 9" 13' 9" 11' 7" 15' 3" f 13' 4" 11' 6" 14' 1" f 12' 5" 10' 9" 13' 2" f 11' 11" 10' 2" 11' 11" f 10' 10" 9' 3"
9
400JS350-97, 50ksi

8 27' 2" 21' 7" 18' 10" 16' 10" 15' 2" 13' 0" 15' 9" 13' 11" 11' 11" 14' 8" 13' 0" 11' 1" 13' 11" 12' 3" 10' 6" 12' 9" 11' 3" 9' 8"
8 19' 10" 15' 9" 13' 9" 15' 9" 13' 9" 11' 7" 14' 7" f 12' 11" 11' 1" 13' 6" f 12' 1" 10' 4" 12' 8" f 11' 5" 9' 10" 11' 4" f 10' 6" 9' 0"
11 10 25' 5" 20' 2" 18' 3" 16' 6" 14' 7" 12' 7" 15' 1" 13' 5" 11' 7" 14' 1" 12' 7" 10' 11" 13' 5" 11' 11" 10' 4" 12' 4" 11' 0" 9' 7"
8 16' 9" 13' 3" 11' 7" 13' 3" 11' 7" 9' 9" 12' 9" f 11' 7" 9' 9" 11' 11" f 11' 5" 9' 9" 11' 2" f 10' 9" 9' 3" 10' 2" f 9' 10" 8' 6"
13 10 19' 10" 15' 9" 13' 9" 15' 5" f 13' 9" 11' 7" 14' 1" f 12' 7" 10' 11" 13' 0" f 11' 10" 10' 3" 12' 3" f 11' 3" 9' 9" 11' 1" f 10' 4" 9' 0"
12 24' 0" 19' 11" 17' 8" 16' 0" 14' 3" 12' 5" 14' 9" 13' 2" 11' 6" 13' 10" 12' 5" 10' 10" 13' 2" 11' 10" 10' 4" 12' 2" 11' 0" 9' 7"
8 14' 11" 11' 10" 10' 4" 11' 10" 10' 4" 8' 9" 11' 6" f 10' 4" 8' 9" 10' 9" f 10' 4" 8' 9" 10' 2" f 10' 2" f 8' 9" 9' 3" f 9' 3" f 8' 1"
15 10 16' 9" 13' 3" 11' 7" 13' 3" 11' 7" 9' 9" 12' 5" f 11' 7" 9' 9" 11' 8" f 11' 3" 9' 8" 11' 0" f 10' 8" 9' 2" 10' 0" f 9' 10" 8' 6"
12 19' 10" 15' 9" 13' 9" 15' 1" f 13' 6" 11' 7" 13' 9" f 12' 6" 10' 10" 12' 10" f 11' 9" 10' 3" 12' 1" f 11' 2" 9' 9" 11' 0" f 10' 4" 9' 0"
6 21' 1" 16' 9" 14' 7" 16' 9" 14' 7" 12' 4" 16' 3" 14' 3" 12' 0" 15' 1" 13' 2" 11' 5" 14' 3" 12' 5" 10' 9" 12' 11" 11' 7" 9' 10"
400JS350-118, 50ksi

9 8 28' 11" 23' 0" 20' 1" 17' 11" 15' 11" 13' 9" 16' 3" 14' 9" 12' 7" 15' 7" 13' 9" 11' 9" 14' 9" 13' 0" 11' 2" 13' 6" 11' 11" 10' 3"
8 21' 1" 16' 9" 14' 7" 16' 9" 14' 7" 12' 4" 15' 8" 13' 9" 11' 9" 14' 7" 12' 10" 11' 0" 13' 9" 12' 1" 10' 5" 12' 7" 11' 1" 9' 6"
11 10 27' 1" 21' 6" 19' 5" 17' 6" 15' 5" 13' 3" 16' 0" 14' 2" 12' 3" 14' 11" 13' 3" 11' 6" 14' 2" 12' 7" 10' 11" 13' 0" 11' 7" 10' 1"
8 17' 9" 14' 1" 12' 4" 14' 1" 12' 4" 10' 5" 14' 1" 12' 4" 10' 5" 13' 4" f 12' 1" 10' 4" 12' 6" f 11' 5" 9' 9" 11' 4" f 10' 6" 9' 0"
13 10 21' 1" 16' 9" 14' 7" 16' 6" 14' 7" 12' 4" 15' 1" 13' 4" 11' 6" 14' 1" 12' 6" 10' 9" 13' 4" 11' 10" 10' 3" 12' 3" 10' 11" 9' 6"
12 25' 7" 21' 2" 18' 8" 16' 11" 15' 0" 13' 1" 15' 7" 13' 10" 12' 1" 14' 7" 13' 1" 11' 5" 13' 10" 12' 5" 10' 11" 12' 10" 11' 6" 10' 1"
8 15' 11" 12' 7" 11' 0" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 0" f 11' 0" 9' 3" 11' 4" f 10' 11" 9' 3" 10' 4" f 9' 11" 8' 6"
15 10 17' 9" 14' 1" 12' 4" 14' 1" 12' 4" 10' 5" 13' 11" f 12' 4" 10' 5" 13' 0" f 11' 10" 10' 3" 12' 3" f 11' 3" 9' 9" 11' 1" f 10' 4" 8' 11"
12 21' 1" 16' 9" 14' 7" 16' 1" 14' 3" 12' 4" 14' 9" 13' 2" 11' 5" 13' 10" 12' 4" 10' 9" 13' 2" 11' 9" 10' 3" 12' 2" f 10' 11" 9' 6"
6 10' 4" f 9' 0" 7' 10" 8' 11" f 7' 10" 6' 7" 8' 5" f 7' 10" 6' 7" 8' 0" f 7' 10" 6' 7" 7' 8" f 7' 8" f 6' 7" 7' 1" f 7' 1" f 6' 7"
9
600JS250-33, 50ksi

8 15' 5" f 12' 11" 11' 4" 11' 9" f 11' 4" 9' 6" 10' 9" f 10' 9" f 9' 6" 10' 1" f 10' 1" f 9' 6" 9' 6" f 9' 6" f 9' 5" 8' 8" f 8' 8" f 8' 8" f
8 10' 3" f 9' 0" 7' 10" 8' 9" f 7' 10" 6' 7" 8' 4" f 7' 10" 6' 7" 7' 11" f 7' 10" 6' 7" 7' 7" f 7' 7" f 6' 7" 7' 1" f 7' 1" f 6' 7"
11 10 15' 0" f 12' 11" 11' 4" 11' 5" f 11' 4" 9' 6" 10' 7" f 10' 7" f 9' 6" 9' 11" f 9' 11" f 9' 6" 9' 5" f 9' 5" f 9' 4" 8' 7" f 8' 7" f 8' 7" f
8 8' 3" f 7' 7" 6' 7" 7' 4" f 6' 7" 5' 7" 7' 0" f 6' 7" 5' 7" 6' 8" f 6' 7" 5' 7" 6' 5" f 6' 5" f 5' 7" 6' 0" f 6' 0" f 5' 7"
13 10 10' 3" f 9' 0" 7' 10" 8' 9" f 7' 10" 6' 7" 8' 4" f 7' 10" 6' 7" 7' 11" f 7' 10" 6' 7" 7' 7" f 7' 7" f 6' 7" 7' 1" f 7' 1" f 6' 7"
12 14' 9" f 12' 11" 11' 4" 11' 5" f 11' 4" 9' 6" 10' 6" f 10' 6" f 9' 6" 9' 11" f 9' 11" f 9' 6" 9' 5" f 9' 5" f 9' 4" 8' 7" f 8' 7" f 8' 7" f
8 7' 0" f 6' 9" 5' 11" 6' 4" f 5' 11" 5' 0" 6' 1" f 5' 11" 5' 0" 5' 11" f 5' 11" f 5' 0" 5' 8" f 5' 8" f 5' 0" 5' 4" f 5' 4" f 5' 0"
15 10 8' 3" f 7' 7" 6' 7" 7' 4" f 6' 7" 5' 7" 7' 0" f 6' 7" 5' 7" 6' 8" f 6' 7" 5' 7" 6' 5" f 6' 5" f 5' 7" 6' 0" f 6' 0" f 5' 7"
12 10' 3" f 9' 0" 7' 10" 8' 9" f 7' 10" 6' 7" 8' 4" f 7' 10" 6' 7" 7' 11" f 7' 10" 6' 7" 7' 7" f 7' 7" f 6' 7" 7' 1" f 7' 1" f 6' 7"
6 12' 4" 9' 9" 8' 6" 9' 9" 8' 6" 7' 2" 9' 9" 8' 6" 7' 2" 9' 9" 8' 6" 7' 2" 9' 5" f 8' 6" 7' 2" 8' 9" f 8' 6" 7' 2"
9
600JS250-43, 50ksi

8 17' 9" 14' 1" 12' 4" 14' 1" 12' 4" 10' 5" 13' 2" f 12' 4" 10' 5" 12' 3" f 12' 3" f 10' 5" 11' 6" f 11' 6" f 10' 3" 10' 4" f 10' 4" f 9' 6"
8 12' 4" 9' 9" 8' 6" 9' 9" 8' 6" 7' 2" 9' 9" 8' 6" 7' 2" 9' 8" f 8' 6" 7' 2" 9' 2" f 8' 6" 7' 2" 8' 6" f 8' 6" f 7' 2"
11 10 17' 9" 14' 1" 12' 4" 13' 10" f 12' 4" 10' 5" 12' 8" f 12' 4" 10' 5" 11' 9" f 11' 9" f 10' 5" 11' 1" f 11' 1" f 10' 2" 10' 2" f 10' 2" f 9' 5"
8 10' 4" f 8' 3" 7' 2" 8' 3" 7' 2" 6' 1" 8' 3" 7' 2" 6' 1" 8' 3" f 7' 2" 6' 1" 7' 11" f 7' 2" 6' 1" 7' 5" f 7' 2" 6' 1"
13 10 12' 4" 9' 9" 8' 6" 9' 9" 8' 6" 7' 2" 9' 9" 8' 6" 7' 2" 9' 7" f 8' 6" 7' 2" 9' 2" f 8' 6" 7' 2" 8' 6" f 8' 6" f 7' 2"
12 17' 9" 14' 1" 12' 4" 13' 7" f 12' 4" 10' 5" 12' 6" f 12' 4" 10' 5" 11' 8" f 11' 8" f 10' 5" 11' 1" f 11' 1" f 10' 2" 10' 2" f 10' 2" f 9' 5"
8 8' 10" f 7' 4" 6' 5" 7' 4" 6' 5" 5' 5" 7' 4" 6' 5" 5' 5" 7' 3" f 6' 5" 5' 5" 7' 0" f 6' 5" 5' 5" 6' 7" f 6' 5" 5' 5"
15 10 10' 3" f 8' 3" 7' 2" 8' 3" 7' 2" 6' 1" 8' 3" 7' 2" 6' 1" 8' 3" f 7' 2" 6' 1" 7' 11" f 7' 2" 6' 1" 7' 5" f 7' 2" 6' 1"
12 12' 4" 9' 9" 8' 6" 9' 9" 8' 6" 7' 2" 9' 9" 8' 6" 7' 2" 9' 7" f 8' 6" 7' 2" 9' 2" f 8' 6" 7' 2" 8' 6" f 8' 6" f 7' 2"

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
25 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 13' 3" 10' 6" 9' 2" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 9' 9" f 9' 2" 7' 9"
9
600JS250-54, 50ksi

8 19' 2" 15' 2" 13' 3" 15' 2" 13' 3" 11' 2" 14' 8" f 13' 3" 11' 2" 13' 7" f 13' 3" 11' 2" 12' 9" f 12' 9" f 11' 1" 11' 5" f 11' 5" f 10' 2"
8 13' 3" 10' 6" 9' 2" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 3" f 9' 2" 7' 9" 9' 5" f 9' 2" 7' 9"
11 10 19' 2" 15' 2" 13' 3" 15' 2" 13' 3" 11' 2" 14' 0" f 13' 3" 11' 2" 13' 0" f 13' 0" f 11' 2" 12' 3" f 12' 3" f 10' 10" 11' 1" f 11' 1" f 10' 0"
8 11' 2" 8' 10" 7' 9" 8' 10" 7' 9" 6' 6" 8' 10" 7' 9" 6' 6" 8' 10" 7' 9" 6' 6" 8' 10" f 7' 9" 6' 6" 8' 2" f 7' 9" 6' 6"
13 10 13' 3" 10' 6" 9' 2" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 1" f 9' 2" 7' 9" 9' 4" f 9' 2" 7' 9"
12 19' 2" 15' 2" 13' 3" 14' 11" f 13' 3" 11' 2" 13' 8" f 13' 3" 11' 2" 12' 9" f 12' 9" f 11' 2" 12' 1" f 12' 1" f 10' 10" 11' 1" f 11' 1" f 10' 0"
8 10' 0" f 7' 11" 6' 11" 7' 11" 6' 11" 5' 10" 7' 11" 6' 11" 5' 10" 7' 11" 6' 11" 5' 10" 7' 10" f 6' 11" 5' 10" 7' 4" f 6' 11" 5' 10"
15 10 11' 2" 8' 10" 7' 9" 8' 10" 7' 9" 6' 6" 8' 10" 7' 9" 6' 6" 8' 10" 7' 9" 6' 6" 8' 9" f 7' 9" 6' 6" 8' 2" f 7' 9" 6' 6"
12 13' 3" 10' 6" 9' 2" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 6" 9' 2" 7' 9" 10' 1" f 9' 2" 7' 9" 9' 4" f 9' 2" 7' 9"
6 14' 3" 11' 4" 9' 10" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 0" f 9' 10" 8' 4"
9
600JS250-68, 50ksi

8 20' 7" 16' 4" 14' 3" 16' 4" 14' 3" 12' 0" 16' 2" f 14' 3" 12' 0" 15' 4" f 14' 3" 12' 0" 14' 4" f 13' 9" 11' 10" 12' 10" f 12' 7" 10' 10"
8 14' 3" 11' 4" 9' 10" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 10' 7" f 9' 10" 8' 4"
11 10 20' 7" 16' 4" 14' 3" 16' 4" 14' 3" 12' 0" 15' 9" f 14' 3" 12' 0" 14' 6" f 14' 0" 12' 0" 13' 7" f 13' 4" 11' 6" 12' 4" f 12' 3" 10' 8"
8 12' 0" 9' 6" 8' 4" 9' 6" 8' 4" 7' 0" 9' 6" 8' 4" 7' 0" 9' 6" 8' 4" 7' 0" 9' 6" 8' 4" 7' 0" 9' 2" f 8' 4" 7' 0"
13 10 14' 3" 11' 4" 9' 10" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 3" f 9' 10" 8' 4" 10' 5" f 9' 10" 8' 4"
12 20' 7" 16' 4" 14' 3" 16' 4" 14' 3" 12' 0" 15' 2" f 14' 3" 12' 0" 14' 1" f 13' 9" 12' 0" 13' 4" f 13' 1" 11' 5" 12' 2" f 12' 1" 10' 7"
8 10' 9" 8' 6" 7' 5" 8' 6" 7' 5" 6' 3" 8' 6" 7' 5" 6' 3" 8' 6" 7' 5" 6' 3" 8' 6" 7' 5" 6' 3" 8' 3" f 7' 5" 6' 3"
15 10 12' 0" 9' 6" 8' 4" 9' 6" 8' 4" 7' 0" 9' 6" 8' 4" 7' 0" 9' 6" 8' 4" 7' 0" 9' 6" 8' 4" 7' 0" 9' 2" f 8' 4" 7' 0"
12 14' 3" 11' 4" 9' 10" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 4" 9' 10" 8' 4" 11' 3" f 9' 10" 8' 4" 10' 5" f 9' 10" 8' 4"
6 15' 11" 12' 7" 11' 0" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3"
9
600JS250-97, 50ksi

8 22' 11" 18' 2" 15' 11" 18' 2" 15' 11" 13' 5" 18' 2" 15' 11" 13' 5" 18' 0" 15' 11" 13' 5" 16' 11" 15' 3" 13' 1" 15' 10" 14' 0" 11' 11"
8 15' 11" 12' 7" 11' 0" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3"
11 10 22' 11" 18' 2" 15' 11" 18' 2" 15' 11" 13' 5" 18' 2" 15' 11" 13' 5" 17' 6" 15' 6" 13' 4" 16' 7" 14' 8" 12' 7" 15' 2" f 13' 6" 11' 8"
8 13' 5" 10' 8" 9' 3" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10"
13 10 15' 11" 12' 7" 11' 0" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" f 11' 0" 9' 3"
12 22' 11" 18' 2" 15' 11" 18' 2" 15' 11" 13' 5" 18' 2" 15' 11" 13' 5" 17' 0" 15' 1" 13' 1" 16' 1" 14' 4" 12' 6" 14' 8" f 13' 3" 11' 7"
8 12' 0" 9' 6" 8' 3" 9' 6" 8' 3" 7' 0" 9' 6" 8' 3" 7' 0" 9' 6" 8' 3" 7' 0" 9' 6" 8' 3" 7' 0" 9' 6" 8' 3" 7' 0"
15 10 13' 5" 10' 8" 9' 3" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10" 10' 8" 9' 3" 7' 10"
12 15' 11" 12' 7" 11' 0" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 7" 11' 0" 9' 3" 12' 6" f 11' 0" 9' 3"
6 16' 10" 13' 5" 11' 8" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10"
600JS250-118, 50ksi

9 8 24' 4" 19' 4" 16' 10" 19' 4" 16' 10" 14' 3" 19' 4" 16' 10" 14' 3" 19' 1" 16' 8" 14' 3" 18' 0" 15' 11" 13' 10" 16' 4" 14' 9" 12' 8"
8 16' 10" 13' 5" 11' 8" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10"
11 10 24' 4" 19' 4" 16' 10" 19' 4" 16' 10" 14' 3" 19' 4" 16' 10" 14' 3" 18' 6" 16' 4" 14' 0" 17' 6" 15' 6" 13' 4" 16' 0" 14' 2" 12' 3"
8 14' 3" 11' 3" 9' 10" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4"
13 10 16' 10" 13' 5" 11' 8" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10"
12 24' 4" 19' 4" 16' 10" 19' 4" 16' 10" 14' 3" 19' 2" 16' 10" 14' 3" 17' 11" 15' 11" 13' 9" 17' 0" 15' 1" 13' 1" 15' 7" 13' 11" 12' 2"
8 12' 8" 10' 1" 8' 10" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5"
15 10 14' 3" 11' 3" 9' 10" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4" 11' 3" 9' 10" 8' 4"
12 16' 10" 13' 5" 11' 8" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10" 13' 5" 11' 8" 9' 10"

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 26
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.
WIND PRESSURE (PSF) AND DEFLECTION LIMITS
Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 18' 8" 14' 10" 12' 11" 14' 10" 12' 11" 10' 11" 14' 10" 12' 11" 10' 11" 13' 11" f 12' 11" 10' 11" 13' 1" f 12' 11" 10' 11" 11' 11" f 11' 11" f 10' 11"
9
600JS350-68, 50ksi

8 26' 11" 21' 5" 18' 8" 19' 6" f 17' 6" 15' 3" 17' 5" f 15' 11" 14' 0" 15' 11" f 15' 3" 13' 0" 15' 2" f 14' 5" 12' 4" 13' 6" f 13' 2" 11' 4"
8 18' 8" 14' 10" 12' 11" 14' 10" 12' 11" 10' 11" 14' 5" f 12' 11" 10' 11" 13' 5" f 12' 11" 10' 11" 12' 8" f 12' 8" f 10' 11" 11' 5" f 11' 5" f 10' 6"
11 10 26' 8" f 21' 5" 18' 8" 18' 8" f 17' 1" 14' 8" 16' 9" f 15' 8" 13' 5" 15' 5" f 14' 8" 12' 7" 14' 4" f 13' 11" 12' 0" 12' 10" f 12' 9" 11' 1"
8 15' 9" 12' 6" 10' 11" 12' 6" 10' 11" 9' 2" 12' 5" f 10' 11" 9' 2" 11' 8" f 10' 11" 9' 2" 11' 1" f 10' 11" 9' 2" 10' 1" f 10' 1" f 9' 2"
13 10 18' 8" 14' 10" 12' 11" 14' 10" 12' 11" 10' 11" 13' 11" f 12' 11" 10' 11" 13' 0" f 12' 11" 10' 11" 12' 3" f 12' 3" f 10' 11" 11' 2" f 11' 2" f 10' 5"
12 25' 4" f 21' 5" 18' 8" 17' 11" f 16' 7" 14' 4" 16' 1" f 15' 3" 13' 3" 14' 10" f 14' 4" 12' 6" 13' 11" f 13' 7" 11' 11" 12' 7" f 12' 7" f 11' 0"
8 14' 0" f 11' 2" 9' 9" 11' 2" 9' 9" 8' 3" 11' 1" f 9' 9" 8' 3" 10' 5" f 9' 9" 8' 3" 9' 11" f 9' 9" 8' 3" 9' 2" f 9' 2" f 8' 3"
15 10 15' 9" 12' 6" 10' 11" 12' 6" 10' 11" 9' 2" 12' 2" f 10' 11" 9' 2" 11' 5" f 10' 11" 9' 2" 10' 11" f 10' 11" f 9' 2" 10' 0" f 10' 0" f 9' 2"
12 18' 8" 14' 10" 12' 11" 14' 10" f 12' 11" 10' 11" 13' 8" f 12' 11" 10' 11" 12' 10" f 12' 10" f 10' 11" 12' 2" f 12' 2" f 10' 11" 11' 1" f 11' 1" f 10' 5"
6 20' 11" 16' 7" 14' 6" 16' 7" 14' 6" 12' 2" 16' 7" 14' 6" 12' 2" 16' 7" 14' 6" 12' 2" 16' 1" f 14' 6" 12' 2" 14' 6" f 14' 5" 12' 2"
9
600JS350-97, 50ksi

8 30' 2" 23' 11" 20' 11" 22' 10" 20' 0" 16' 10" 20' 9" 18' 2" 15' 9" 19' 3" 16' 10" 14' 9" 18' 1" f 15' 11" 13' 11" 15' 11" f 14' 11" 12' 9"
8 20' 11" 16' 7" 14' 6" 16' 7" 14' 6" 12' 2" 16' 7" 14' 6" 12' 2" 15' 11" f 14' 6" 12' 2" 15' 4" f 14' 6" 12' 2" 13' 10" f 13' 10" f 11' 10"
11 10 30' 2" 23' 11" 20' 11" 21' 5" 19' 4" 16' 6" 19' 11" f 17' 8" 15' 1" 18' 8" f 16' 6" 14' 2" 17' 4" f 15' 7" 13' 5" 15' 5" f 14' 4" 12' 4"
8 17' 7" 14' 0" 12' 2" 14' 0" 12' 2" 10' 3" 14' 0" 12' 2" 10' 3" 14' 0" 12' 2" 10' 3" 13' 4" f 12' 2" 10' 3" 12' 2" f 12' 2" f 10' 3"
13 10 20' 11" 16' 7" 14' 6" 16' 7" 14' 6" 12' 2" 16' 7" 14' 6" 12' 2" 15' 8" f 14' 6" 12' 2" 14' 9" f 14' 6" 12' 2" 13' 4" f 13' 4" f 11' 7"
12 30' 2" 23' 11" 20' 11" 21' 1" 18' 7" 16' 0" 19' 4" 17' 1" 14' 9" 17' 10" f 16' 0" 13' 10" 16' 7" f 15' 2" 13' 2" 14' 11" f 14' 0" 12' 2"
8 15' 9" 12' 6" 10' 11" 12' 6" 10' 11" 9' 2" 12' 6" 10' 11" 9' 2" 12' 6" 10' 11" 9' 2" 12' 0" f 10' 11" 9' 2" 11' 0" f 10' 11" 9' 2"
15 10 17' 7" 14' 0" 12' 2" 14' 0" 12' 2" 10' 3" 14' 0" 12' 2" 10' 3" 13' 9" f 12' 2" 10' 3" 13' 0" f 12' 2" 10' 3" 11' 11" f 11' 11" f 10' 3"
12 20' 11" 16' 7" 14' 6" 16' 7" 14' 6" 12' 2" 16' 4" f 14' 6" 12' 2" 15' 3" f 14' 6" 12' 2" 14' 4" f 14' 4" f 12' 2" 13' 1" f 13' 1" f 11' 7"
6 22' 2" 17' 7" 15' 4" 17' 7" 15' 4" 13' 0" 17' 7" 15' 4" 13' 0" 17' 7" 15' 4" 13' 0" 17' 7" 15' 4" 13' 0" 16' 4" f 15' 4" 13' 0"
600JS350-118, 50ksi

9 8 32' 0" 25' 5" 22' 2" 24' 5" 21' 4" 18' 0" 22' 3" 19' 5" 16' 4" 20' 7" 18' 0" 15' 8" 19' 5" 16' 11" 14' 10" 17' 7" 15' 10" 13' 6"
8 22' 2" 17' 7" 15' 4" 17' 7" 15' 4" 13' 0" 17' 7" 15' 4" 13' 0" 17' 7" 15' 4" 13' 0" 16' 11" f 15' 4" 13' 0" 15' 7" f 14' 10" 12' 7"
11 10 32' 0" 25' 5" 22' 2" 22' 10" 20' 0" 17' 6" 20' 9" 18' 9" 16' 1" 19' 11" 17' 6" 15' 0" 18' 9" 16' 7" 14' 3" 17' 2" 15' 2" 13' 1"
8 18' 9" 14' 10" 13' 0" 14' 10" 13' 0" 10' 11" 14' 10" 13' 0" 10' 11" 14' 10" 13' 0" 10' 11" 14' 10" 13' 0" 10' 11" 13' 8" f 13' 0" 10' 11"
13 10 22' 2" 17' 7" 15' 4" 17' 7" 15' 4" 13' 0" 17' 7" 15' 4" 13' 0" 17' 6" f 15' 4" 13' 0" 16' 6" f 15' 4" 13' 0" 14' 11" f 14' 4" 12' 4"
12 32' 0" 25' 5" 22' 2" 22' 5" 19' 9" 17' 0" 20' 6" 18' 2" 15' 7" 19' 2" 17' 0" 14' 8" 18' 2" 16' 1" 13' 11" 16' 7" f 14' 10" 12' 10"
8 16' 9" 13' 3" 11' 7" 13' 3" 11' 7" 9' 9" 13' 3" 11' 7" 9' 9" 13' 3" 11' 7" 9' 9" 13' 3" 11' 7" 9' 9" 12' 4" f 11' 7" 9' 9"
15 10 18' 9" 14' 10" 13' 0" 14' 10" 13' 0" 10' 11" 14' 10" 13' 0" 10' 11" 14' 10" 13' 0" 10' 11" 14' 6" f 13' 0" 10' 11" 13' 3" f 13' 0" 10' 11"
12 22' 2" 17' 7" 15' 4" 17' 7" 15' 4" 13' 0" 17' 7" 15' 4" 13' 0" 17' 0" f 15' 4" 13' 0" 16' 0" f 15' 3" 13' 0" 14' 6" f 14' 1" 12' 2"
6 12' 9" 10' 1" 8' 10" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 9' 6" f 8' 10" 7' 5"
9
800JS250-43, 50ksi

8 18' 4" 14' 7" 12' 9" 14' 7" 12' 9" 10' 9" 14' 7" f 12' 9" 10' 9" 13' 7" f 12' 9" 10' 9" 12' 9" f 12' 9" f 10' 9" 11' 6" f 11' 6" f 10' 9"
8 12' 9" 10' 1" 8' 10" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 0" f 8' 10" 7' 5" 9' 3" f 8' 10" 7' 5"
11 10 18' 4" 14' 7" 12' 9" 14' 7" 12' 9" 10' 9" 13' 11" f 12' 9" 10' 9" 13' 0" f 12' 9" 10' 9" 12' 3" f 12' 3" f 10' 9" 11' 2" f 11' 2" f 10' 9"
8 10' 8" f 8' 6" 7' 5" 8' 6" 7' 5" 6' 3" 8' 6" 7' 5" 6' 3" 8' 6" 7' 5" 6' 3" 8' 6" f 7' 5" 6' 3" 8' 0" f 7' 5" 6' 3"
13 10 12' 9" 10' 1" 8' 10" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 9' 11" f 8' 10" 7' 5" 9' 3" f 8' 10" 7' 5"
12 18' 4" 14' 7" 12' 9" 14' 7" 12' 9" 10' 9" 13' 8" f 12' 9" 10' 9" 12' 9" f 12' 9" f 10' 9" 12' 1" f 12' 1" f 10' 9" 11' 1" f 11' 1" f 10' 9"
8 9' 1" f 7' 7" 6' 8" 7' 7" 6' 8" 5' 7" 7' 7" 6' 8" 5' 7" 7' 7" 6' 8" 5' 7" 7' 6" f 6' 8" 5' 7" 7' 1" f 6' 8" 5' 7"
15 10 10' 8" f 8' 6" 7' 5" 8' 6" 7' 5" 6' 3" 8' 6" 7' 5" 6' 3" 8' 6" 7' 5" 6' 3" 8' 6" f 7' 5" 6' 3" 8' 0" f 7' 5" 6' 3"
12 12' 9" 10' 1" 8' 10" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 10' 1" 8' 10" 7' 5" 9' 11" f 8' 10" 7' 5" 9' 3" f 8' 10" 7' 5"

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
27 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 13' 8" 10' 10" 9' 6" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0"
9
800JS250-54, 50ksi

8 19' 9" 15' 8" 13' 8" 15' 8" 13' 8" 11' 6" 15' 8" 13' 8" 11' 6" 15' 7" f 13' 8" 11' 6" 14' 7" f 13' 8" 11' 6" 13' 2" f 13' 2" f 11' 6"
8 13' 8" 10' 10" 9' 6" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 7" f 9' 6" 8' 0"
11 10 19' 9" 15' 8" 13' 8" 15' 8" 13' 8" 11' 6" 15' 8" 13' 8" 11' 6" 14' 10" f 13' 8" 11' 6" 13' 11" f 13' 8" 11' 6" 12' 8" f 12' 8" f 11' 6"
8 11' 6" 9' 2" 8' 0" 9' 2" 8' 0" 6' 9" 9' 2" 8' 0" 6' 9" 9' 2" 8' 0" 6' 9" 9' 2" 8' 0" 6' 9" 9' 1" f 8' 0" 6' 9"
13 10 13' 8" 10' 10" 9' 6" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 5" f 9' 6" 8' 0"
12 19' 9" 15' 8" 13' 8" 15' 8" 13' 8" 11' 6" 15' 5" f 13' 8" 11' 6" 14' 5" f 13' 8" 11' 6" 13' 7" f 13' 7" f 11' 6" 12' 5" f 12' 5" f 11' 6"
8 10' 4" f 8' 2" 7' 2" 8' 2" 7' 2" 6' 0" 8' 2" 7' 2" 6' 0" 8' 2" 7' 2" 6' 0" 8' 2" 7' 2" 6' 0" 8' 1" f 7' 2" 6' 0"
15 10 11' 6" 9' 2" 8' 0" 9' 2" 8' 0" 6' 9" 9' 2" 8' 0" 6' 9" 9' 2" 8' 0" 6' 9" 9' 2" 8' 0" 6' 9" 9' 0" f 8' 0" 6' 9"
12 13' 8" 10' 10" 9' 6" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 10" 9' 6" 8' 0" 10' 5" f 9' 6" 8' 0"
6 14' 9" 11' 8" 10' 2" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7"
9
800JS250-68, 50ksi

8 21' 3" 16' 10" 14' 9" 16' 10" 14' 9" 12' 5" 16' 10" 14' 9" 12' 5" 16' 10" 14' 9" 12' 5" 16' 1" f 14' 9" 12' 5" 14' 11" f 14' 9" 12' 5"
8 14' 9" 11' 8" 10' 2" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7"
11 10 21' 3" 16' 10" 14' 9" 16' 10" 14' 9" 12' 5" 16' 10" 14' 9" 12' 5" 16' 8" f 14' 9" 12' 5" 15' 8" f 14' 9" 12' 5" 14' 2" f 14' 2" f 12' 5"
8 12' 5" 9' 10" 8' 7" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3"
13 10 14' 9" 11' 8" 10' 2" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" f 10' 2" 8' 7"
12 21' 3" 16' 10" 14' 9" 16' 10" 14' 9" 12' 5" 16' 10" 14' 9" 12' 5" 16' 1" f 14' 9" 12' 5" 15' 2" f 14' 9" 12' 5" 13' 9" f 13' 9" f 12' 5"
8 11' 1" 8' 9" 7' 8" 8' 9" 7' 8" 6' 6" 8' 9" 7' 8" 6' 6" 8' 9" 7' 8" 6' 6" 8' 9" 7' 8" 6' 6" 8' 9" 7' 8" 6' 6"
15 10 12' 5" 9' 10" 8' 7" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3"
12 14' 9" 11' 8" 10' 2" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 7" f 10' 2" 8' 7"
6 16' 5" 13' 0" 11' 4" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7"
9
800JS250-97, 50ksi

8 23' 8" 18' 10" 16' 5" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 18' 3" f 16' 5" 13' 10"
8 16' 5" 13' 0" 11' 4" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7"
11 10 23' 8" 18' 10" 16' 5" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 17' 6" f 16' 5" 13' 10"
8 13' 10" 11' 0" 9' 7" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1"
13 10 16' 5" 13' 0" 11' 4" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7"
12 23' 8" 18' 10" 16' 5" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 18' 10" 16' 5" 13' 10" 18' 8" f 16' 5" 13' 10" 16' 10" f 16' 0" 13' 10"
8 12' 4" 9' 10" 8' 7" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3" 9' 10" 8' 7" 7' 3"
15 10 13' 10" 11' 0" 9' 7" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1" 11' 0" 9' 7" 8' 1"
12 16' 5" 13' 0" 11' 4" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7" 13' 0" 11' 4" 9' 7"
6 17' 5" 13' 10" 12' 1" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2"
800JS250-118, 50ksi

9 8 25' 2" 19' 11" 17' 5" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8"
8 17' 5" 13' 10" 12' 1" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2"
11 10 25' 2" 19' 11" 17' 5" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 3" f 17' 5" 14' 8"
8 14' 8" 11' 8" 10' 2" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7"
13 10 17' 5" 13' 10" 12' 1" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2"
12 25' 2" 19' 11" 17' 5" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 19' 11" 17' 5" 14' 8" 18' 5" f 16' 11" 14' 7"
8 13' 2" 10' 5" 9' 1" 10' 5" 9' 1" 7' 8" 10' 5" 9' 1" 7' 8" 10' 5" 9' 1" 7' 8" 10' 5" 9' 1" 7' 8" 10' 5" 9' 1" 7' 8"
15 10 14' 8" 11' 8" 10' 2" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7" 11' 8" 10' 2" 8' 7"
12 17' 5" 13' 10" 12' 1" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2" 13' 10" 12' 1" 10' 2"

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 28
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS JAMSTUD ALLOWABLE HEADER SPANS

Important Notes
1. A sheathing dead load of 12 psf acting vertically on the header is considered in the calculations.
2. No load factor for lateral wind pressure is used for strength determination as per ASD basic load
combinations in ASCE 7-05 and IBC 2006.
3. A load factor of 0.7 for lateral wind pressure is used for deflection determination as per IBC
2006, Sec. 1604.3 and AISI-Wall Stud Design Std. 2004, Sec. B1 (Except for 5psf lateral
pressure where 1.0 load factor is used.)
4. "f" denotes limiting header span is controlled by strength. All other spans are controlled by deflection.
5. If wind reduction factor for deflection determination is not allowed by a specific building code, multiply table
values not denoted by f by 85% to calculate the proper JS header span. Table values denoted by f are
controlled by strength and should not be reduced.
6. Header is assumed to be connected to jamb member through a stiffening clip to eliminate a web crippling
condition.
7. Limiting header spans are based on continuous support of each flange over the full length of the member.
8. Strength determination includes checks for bending and shear capacity values of the header.
9. Designate JamStud without punchouts on drawings when utilized for header applications.

WIND PRESSURE (PSF) AND DEFLECTION LIMITS


Wall Ht. (ft)

Height (ft)
JamStud

Opening
Member

5 psf 15 psf 20 psf 25 psf 30 psf 40 psf


L/120 L/240 L/360 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600 L/240 L/360 L/600

6 19' 4" 15' 4" 13' 5" 15' 4" 13' 5" 11' 3" 15' 4" 13' 5" 11' 3" 15' 4" 13' 5" 11' 3" 15' 0" f 13' 5" 11' 3" 13' 8" f 13' 5" 11' 3"
9
800JS350-68, 50ksi

8 27' 10" 22' 1" 19' 4" 22' 1" 19' 4" 16' 3" 20' 5" f 19' 4" 16' 3" 18' 8" f 18' 5" 15' 11" 17' 4" f 17' 4" f 15' 1" 15' 10" f 15' 10" f 13' 10"
8 19' 4" 15' 4" 13' 5" 15' 4" 13' 5" 11' 3" 15' 4" 13' 5" 11' 3" 15' 3" f 13' 5" 11' 3" 14' 5" f 13' 5" 11' 3" 13' 2" f 13' 2" f 11' 3"
11 10 27' 10" 22' 1" 19' 4" 21' 1" f 19' 4" 16' 3" 19' 6" f 19' 2" 16' 3" 17' 11" f 17' 11" f 15' 4" 16' 8" f 16' 8" f 14' 6" 14' 11" f 14' 11" f 13' 4"
8 16' 3" 12' 11" 11' 3" 12' 11" 11' 3" 9' 6" 12' 11" 11' 3" 9' 6" 12' 11" 11' 3" 9' 6" 12' 5" f 11' 3" 9' 6" 11' 6" f 11' 3" 9' 6"
13 10 19' 4" 15' 4" 13' 5" 15' 4" 13' 5" 11' 3" 15' 4" 13' 5" 11' 3" 14' 9" f 13' 5" 11' 3" 13' 11" f 13' 5" 11' 3" 12' 9" f 12' 9" f 11' 3"
12 27' 10" 22' 1" 19' 4" 20' 8" f 19' 4" 16' 3" 18' 7" f 18' 6" 15' 11" 17' 2" f 17' 2" f 14' 11" 16' 1" f 16' 1" f 14' 2" 14' 6" f 14' 6" f 13' 1"
8 14' 7" 11' 6" 10' 1" 11' 6" 10' 1" 8' 6" 11' 6" 10' 1" 8' 6" 11' 6" 10' 1" 8' 6" 11' 1" f 10' 1" 8' 6" 10' 4" f 10' 1" 8' 6"
15 10 16' 3" 12' 11" 11' 3" 12' 11" 11' 3" 9' 6" 12' 11" 11' 3" 9' 6" 12' 9" f 11' 3" 9' 6" 12' 2" f 11' 3" 9' 6" 11' 3" f 11' 3" f 9' 6"
12 19' 4" 15' 4" 13' 5" 15' 4" 13' 5" 11' 3" 15' 4" f 13' 5" 11' 3" 14' 5" f 13' 5" 11' 3" 13' 8" f 13' 5" 11' 3" 12' 7" f 12' 7" f 11' 3"
6 21' 7" 17' 2" 15' 0" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 16' 8" f 15' 0" 12' 7"
9
800JS350-97, 50ksi

8 31' 2" 24' 9" 21' 7" 24' 9" 21' 7" 18' 3" 24' 9" 21' 7" 18' 3" 22' 11" f 21' 0" 17' 8" 21' 3" f 19' 9" 16' 8" 18' 10" f 17' 11" 15' 7"
8 21' 7" 17' 2" 15' 0" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 17' 2" f 15' 0" 12' 7" 15' 11" f 15' 0" 12' 7"
11 10 31' 2" 24' 9" 21' 7" 24' 9" 21' 7" 18' 3" 23' 1" f 21' 2" 18' 3" 21' 2" f 19' 11" 17' 3" 19' 11" f 19' 1" 16' 4" 18' 0" f 17' 6" 15' 0"
8 18' 3" 14' 5" 12' 7" 14' 5" 12' 7" 10' 8" 14' 5" 12' 7" 10' 8" 14' 5" 12' 7" 10' 8" 14' 5" 12' 7" 10' 8" 13' 10" f 12' 7" 10' 8"
13 10 21' 7" 17' 2" 15' 0" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 16' 9" f 15' 0" 12' 7" 15' 3" f 15' 0" 12' 7"
12 31' 2" 24' 9" 21' 7" 24' 3" f 21' 7" 18' 3" 22' 5" f 20' 10" 17' 10" 20' 8" f 19' 6" 16' 9" 19' 3" f 18' 5" 15' 10" 17' 3" f 16' 11" 14' 7"
8 16' 3" 12' 11" 11' 3" 12' 11" 11' 3" 9' 6" 12' 11" 11' 3" 9' 6" 12' 11" 11' 3" 9' 6" 12' 11" 11' 3" 9' 6" 12' 5" f 11' 3" 9' 6"
15 10 18' 3" 14' 5" 12' 7" 14' 5" 12' 7" 10' 8" 14' 5" 12' 7" 10' 8" 14' 5" 12' 7" 10' 8" 14' 5" 12' 7" 10' 8" 13' 5" f 12' 7" 10' 8"
12 21' 7" 17' 2" 15' 0" 17' 2" 15' 0" 12' 7" 17' 2" 15' 0" 12' 7" 17' 2" f 15' 0" 12' 7" 16' 3" f 15' 0" 12' 7" 14' 10" f 14' 10" f 12' 7"
6 23' 0" 18' 3" 15' 11" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5"
800JS350-118, 50ksi

9 8 33' 2" 26' 3" 23' 0" 26' 3" 23' 0" 19' 4" 26' 3" 23' 0" 19' 4" 25' 9" 22' 6" 18' 11" 24' 1" f 21' 2" 17' 10" 21' 5" f 19' 2" 16' 2"
8 23' 0" 18' 3" 15' 11" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 17' 6" f 15' 11" 13' 5"
11 10 33' 2" 26' 3" 23' 0" 26' 3" 23' 0" 19' 4" 25' 11" 22' 8" 19' 4" 23' 11" f 21' 0" 18' 5" 22' 2" f 19' 11" 17' 4" 19' 11" f 18' 7" 15' 11"
8 19' 4" 15' 4" 13' 5" 15' 4" 13' 5" 11' 4" 15' 4" 13' 5" 11' 4" 15' 4" 13' 5" 11' 4" 15' 4" 13' 5" 11' 4" 15' 4" 13' 5" 11' 4"
13 10 23' 0" 18' 3" 15' 11" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 17' 1" f 15' 11" 13' 5"
12 33' 2" 26' 3" 23' 0" 26' 3" 23' 0" 19' 4" 24' 6" f 22' 3" 19' 0" 23' 2" f 20' 9" 17' 9" 21' 7" f 19' 7" 16' 10" 19' 3" f 18' 0" 15' 6"
8 17' 4" 13' 9" 12' 0" 13' 9" 12' 0" 10' 1" 13' 9" 12' 0" 10' 1" 13' 9" 12' 0" 10' 1" 13' 9" 12' 0" 10' 1" 13' 9" 12' 0" 10' 1"
15 10 19' 4" 15' 4" 13' 5" 15' 4" 13' 5" 11' 4" 15' 4" 13' 5" 11' 4" 15' 4" 13' 5" 11' 4" 15' 4" 13' 5" 11' 4" 15' 0" f 13' 5" 11' 4"
12 23' 0" 18' 3" 15' 11" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 3" 15' 11" 13' 5" 18' 2" f 15' 11" 13' 5" 16' 6" f 15' 11" 13' 5"

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
29 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS CONNECTIONS
PRIMARY STRUCTURAL DEFLECTION
All structures deflect vertically. To prevent non-axial-load-bearing studs from carrying the weight of the structure and to protect finishes, vertical deflec-
tion connections should be incorporated at the earliest possible moment of project design. The load-carrying capacity of a steel stud in bending is

reduced significantly when adding an axial force propagated by the bending of a primary beam or slab. VertiClip was developed to prevent the crush-
ing effect on non-axial-load-bearing wall studs. Non-axial-load-bearing wall studs include exterior curtain wall and interior wall assemblies. When project

conditions dictate, lateral drift and vertical deflection may be accommodated through utilization of TSNs DriftClip and DriftTrak lines of connectors.
Finished walls frequently experience cracking, buckling, or crushing due to improp-
er isolation of building movement. The movement of the primary building struc-
ture is largely accounted for in horizontal member live loading. In addition to live
loads, wind, seismic forces, moisture content in materials, and temperature cycles
all contribute to movement. The incorporation of vertical deflection connections
during the working drawing phase will eliminate the liability of failures and added
costs associated with wall system installation. The VertiClip and DriftClip series of
mechanical connectors is a complete solution for all vertical deflection configura-
tions. Substantial effort has been made to standardize construction practices thus
ensuring the positive connections of light steel framing components. VertiClip has
undergone extensive field and independent laboratory testing to achieve a true
slip connection solution that isolates all secondary frame components from loads
induced by vertical movement.

90% of failures begin at connections.


Why take chances?
Pictured are two curtain wall bypass ap-
plications, with the left picture showing

TSN's VertiClip SLB connecting studs to
the structure, and on the right is a slotted
angle and one screw attaching to the stud.

VertiClip SLB is manufactured from 50ksi,
G-90, stiffened 14ga steel material and
contains pre-installed step bushings in
slots to offset the screw attachment to the
stud, allowing for free structural move-
ment. The material composition of the clip
at right is unclear, and the load capacity is
significantly lower with only one screw and
a flat steel plate. In addition, there is noth-
ing to offset the screw attachment from the
stud, resulting in a rigid attachment. Some
movement may then be allowed by backing
the screw out a distance, but when that happens, allowable load calculations are rendered useless, as screw values depend on a firmly-seated screw.

Specifying TSN's VertiClip , VertiTrack , DriftClip , or DriftTrak eliminates the use of untested scrap angles and protects liability.

Step Bushing Technology allows for positive,


load tested attachments. Protect liability by using Step Bushing
Factor
Generic Angle
Technology with Slots
TSN Products Tight friction attach-
Friction-Free
Movement? ment (unless screw
Movement
is backed out)
Structurally Load If a screw is backed
Tested (Meets ICC-ES Testing? out, load capacity is
AC261) nullified
ICC-ESR-1903 & No ICC-ES or LARR
Code
LARR 25631 issued for certifications exist for
Approvals?
VertiClip generic clip angle
TSN utilizes only mill- Material
Unknown
certified, 50ksi steel Composition?

Each exterior VertiClip
Galvanized
& DriftClip has a G90 Unknown
Coatings?
galvanized coating
Step Bushings are pre- Screw
No guide offered
installed in each clip Placement?
Allows for friction-free structural movement
Enables the fastener to firmly seat during installation Contractor respon-
Rated screws are
Results in a fully-engineered, liability-protecting connection providing the performance Screw Type? sible for screw type
provided with each clip
and peace of mind you need used

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 30
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
VERTICLIP
VERTICAL DEFLECTION CONNECTORS
BYPASS SLAB CONDITION BYPASS STRUCTURE CONDITION
Provides for tolerance of studs
VERTICLIP SLB

from deck VERTICLIP SLS

Attaches to horizontal surfaces,


eliminating heavy reinforced
slab closure plates (SLS)
Quick and easy way to plumb
studs
No time spent installing extra
scabs or shims
Step Bushings pre-installed
Tested screws provided

US Patents #5,467,566 & #5,906,080 US Patents #5,467,566 & #5,906,080

BYPASS TOP OF SLAB CONDITION BYPASS TOP OF SLAB CONDITION


VERTICLIP SLT
VERTICLIP SLT(L)

Provides for tolerance of studs


from deck
Attaches to horizontal surfaces,
eliminating heavy reinforced
slab closure plates
Quick and easy way to plumb
studs
No time spent installing extra
scabs or shims
Step Bushings pre-installed
Tested screws provided

US Patents #5,467,566 & #5,906,080 US Patents #5,467,566 & #5,906,080

An ICC-ES Evaluation Report for VertiClips SL362, 600,


800, SLD600, SLB600, SLS600-12, SLT 9.5 & SLT(L)-18
is available. Refer to ICC-ESR-1903 at www.icc-es.org
or at www.steelnetwork.com.

HEAD OF WALL CONDITION HEAD OF WALL CONDITION


VERTITRACK VTX
VERTICLIP SL

Pre-spaced clips at 12", 16", or



24" o.c. (VertiTrack )
Eliminates loose friction held
track assemblies
Top of wall bridging or
strapping is eliminated
Top track is not structural,
downsized to 20ga (standard
leg)
Step Bushings pre-installed
Tested screws provided

US Patents #5,467,566 & #5,906,080 US Patents #5,467,566 & #5,906,080

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
31 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
DRIFTCLIP
AND DRIFTTRAK
VERTICAL DEFLECTION & LATERAL DRIFT
BYPASS SLAB CONDITION BYPASS SLAB CONDITION
DRIFTTRAK DTSLB
DRIFTCLIP DSLB

Provides for tolerance of


studs from deck

DriftTrak - drift amount limited
only to stud spacing and wall
termination
Quick and easy way to plumb
studs
No time spent installing extra
scabs or shims
Step Bushings pre-installed
Tested screws provided for
US Patent #'s 7,503150 & 7,104,024 attachment to stud US Patent #'s 6,612,087 & 7,104,024

BYPASS STRUCTURE CONDITION


Provides for tolerance of studs DRIFTCLIP DSLS

from deck
Attaches to underside of wide
flange beam
Quick and easy way to plumb
studs
No time spent installing extra
An ICC-ES Evaluation Report for
DriftClips DSLB, DSLS, DSL and scabs or shims
Step Bushings pre-installed
DriftTraks DTSLB and DTSL is available.
Tested screws provided for
Refer to ICC-ESR-2049 at www.icc-es.org
attachment to stud
or at www.steelnetwork.com.
US Patent #'s 6,612,087 & 7,104,024

HEAD OF WALL CONDITION HEAD OF WALL CONDITION


DRIFTTRAK DTSL


DRIFTCLIP DSL

DriftTrak - drift amount limited


only to stud spacing and wall
termination
Eliminates loose friction held
track assemblies
Top track is not structural,
downsized to 20ga (standard
leg)
Step Bushings pre-installed
Tested screws provided for
attachment to stud
US Patent #'s 7,503150 & 7,104,024 US Patent #'s 6,612,087 & 7,104,024

HEADER CONNECTOR MULTI-PURPOSE CONNECTOR WALL BACKING


STIFFCLIP HE
STIFFCLIP AL
BACKIT

US Patent # 7,634,889 US Patent # 7,559,519


Eliminates Jack Studs Availablein 3.625", 6", and 8" sizes Eliminates Jack Studs
Shelf ledge to rest header upon Manufactured from mill-certified steel Shelf ledge to rest header upon
during installation Guide holes for fast attachments during installation
Guide holes for fast attachments Guide holes for fast attachments

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 32
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
CURTAIN WALL SYSTEMS BRIDGING
BRIDGING BACKGROUND
Bridging for load bearing studs is needed to resist the following forces:
1 - Weak axis buckling induced by axial compression load.
2 - Torsion induced by wind load.
AISI Wall Stud Design Standard (2004), referenced by 2006 IBC; or AISI-NAS Specification (2007) provides the load and stiffness
requirements for bracing members due to the effects of axial compression load and wind load as given in the table below. Contact TSN
Technical Support (888) 474-4876 if further information is needed regarding wall bridging design.

As lateral wind loads are applied, wall


studs react with torsional rotation. To
offset these forces, a form of bridging is
incorporated into the wall system.

BRIDGING REQUIREMENTS
Load Capacity:
Twist Load PL = 1.5 x Wind Load x Bridging Spacing x Stud Spacing x m(Shear Center Distance) / Stud Depth.
WIND
Twist Moment M1 = PL x Stud Depth.

Bridging curtain wall studs against torsion by wind


JamStud

BridgeClip
BC600/BC800 BridgeBar

US Patent # 5,904,023
Twist and snap installation Tabs clasp bridging channel Press grooves into stud punchouts
No clamping or welding required No clamping or welding required Place by hand (no pounding required)
Reduction in # of screws used Guide holes provided for quick and No clamping or welding required
Guide holes provided for quick and accurate fastener placement Quickly secure to stud with BridgeClip

accurate fastener placement Rounded edges for safety


Rounded edges for safety

The bridging examples shown on this page represent practical application solutions. Connec-
tion use is dependant upon project load requirements. The chart on page 34 provides a quick
reference for selecting a TSN curtain wall bridging solution. Other engineered products are
found in The Steel Networks Light Steel Framing Connection Catalog. Contact TSNs Technical
Support Team for design recommendations.

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
33 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS BRIDGING CHART
10psf 20psf 30psf 40psf 50psf
Stud Designation Design Wind Pressure and Stud Spacing
16 o.c. 24 o.c. 16 o.c. 24 o.c. 16 o.c. 24 o.c. 16 o.c. 24 o.c. 16 o.c. 24 o.c.
362S162-33mil, 33ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S162-43mil, 33ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S162-54mil, 50ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S162-68mil, 50ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S162-97mil, 50ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S162-33mil, 33ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S162-43mil, 33ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S162-54mil, 50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S162-68mil, 50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S162-97mil, 50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S162-118mil,50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S162-33mil, 33ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S162-43mil, 33ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S162-54mil, 50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S162-68mil, 50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S162-97mil, 50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S162-118mil,50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
362S200-33mil, 33ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S200-43mil, 33ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S200-54mil, 50ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S200-68mil, 50ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
362S200-97mil, 50ksi BB / BC1 BB / BC1 BB / BC1 BB / BC3 BB / BC3 BB / BC3 BB / BC3 FS / SB FS / SB FS / SB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S200-33mil, 33ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S200-43mil, 33ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S200-54mil, 50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S200-68mil, 50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S200-97mil, 50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC1 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC3 or BB / BC600 BB / BC600 BB / BC600
600S200-118mil,50ksi BkB BkB BkB BkB BkB BkB BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S200-33mil, 33ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S200-43mil, 33ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S200-54mil, 50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S200-68mil, 50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S200-97mil, 50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
BB / BC1 or BB / BC1 or BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800 BB / BC800
800S200-118mil,50ksi BkB BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB or BkB
Important Notes:
1. Bridging located horizontally at 60 o.c. maximum spacing.
2. Calculated Twist Load (Reference NASPEC 2001): 1.5 x Wind Load x Bridging Spacing x Stud Spacing x m (distance from stud web to shear center)
3. Nomenclature:
BB / BC1 - BridgeBar 150 attached to stud using BridgeClip with 1 screw

BkB - BuckleBridge attached to stud with 2 screws

BB / BC3 - BridgeBar 150 attached to stud using BridgeClip with 3 screws FS / SB - Flat Strap with Solid Blocking every 8
BB / BC600 - BridgeBar 150 attached to stud using BC600 with 4 screws BB / BC800 - BridgeBar 150 attached to stud using BC800 with 4
screws

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 34
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330
DESIGN SOFTWARE STEELSMART SYSTEM

The industrys #1 tool for the design


of Members...Connections...
Fasteners...Details
Component Design Modules:
Curtain Wall
Load Bearing Wall
X-Brace Shear Wall
Floor Framing
Roof Framing
Roof Trusses
Moment Resisting Short Wall

Order online at www.steelsmartsystem.com

Load Generator and Distributor


The Lateral Load Generator/Distributor tool uses the dimensions
and load specification for a building and calculates the total Layout & Details Drawing Generator
lateral wind and seismic loads according to ASCE 7 Standard A major addition to SSS 6.0 is the new Layout and Connection
Minimum Design Loads for Buildings and Other Structures. Details Generator that plots framing layout of the wall and adds
Then, the tool distributes the lateral loads between floors and the connection design data (clip designation, # of fasteners,
between shear walls in each floor. The distribution method takes embedment, and screw pattern) to the typical connection detail.
into consideration type of floor diaphragm (rigid or flexible) and The drawing also includes framing members cross-sections
torsional effects of rigid diaphragms. The tool exports load data and shapes. The drawing can be exported in AutoCAD DXF
to SW design module and full output to a standard Excel sheet. format.

Contact ASI for licensing information:


Phone: (919) 645-4090
Fax: (919) 645-4085
Web site: www.appliedscienceint.com
Email: asi@appliedscienceint.com

Raleigh, NC : Phone (919) 845-1025 Toll Free Nationwide Phone (888) 474-4876
35 Jan 2010
Las Vegas, NV : Phone (702) 643-4330 www.steelnetwork.com
CURTAIN WALL SYSTEMS WARRANTY
PRODUCT USE
Products in this catalog are designed and manufactured for the specific purposes shown, and should not be used in other applications unless approved
by a qualified design professional. All modifications to products or changes in installation procedures should be made by a qualified design professional.
The performance of such modified products or altered installation procedures is the sole responsibility of the design professional or installation contractor.
The installation contractor and/or qualified design professional are responsible for installing all products in accordance with relevant specifications and
building codes.
Customers modifying products or installation procedures, or designing non-standard products for fabrication by The Steel Network, Inc. ("TSN") shall,
regardless of specific instructions to the user, indemnify, defend, and hold TSN harmless for any and all claimed loss or damage occasioned in whole or
in part by non-standard or modified products or installation procedures.
Loads in this catalog are for the described specific applications of properly installed products. Modifications to TSN products, improper loading or instal-
lation procedures, or deviations from recommended applications will affect TSN products' load-carrying capacities. TSN products are fabricated from hot-
dipped galvanized steel for corrosion protection but will corrode and lose load-carrying capacity if exposed to salt air, corrosive fire-retardant chemicals,
fertilizers, pressure treated wood or other substances that may adversely affect steel or its galvanized coating. This document edition reflects changes
in the allowable loads and configurations of some of TSN's products. This information supercedes information in earlier documents or technical reports.
All earlier documents or technical reports should be discarded and reference made exclusively to this May 2009 edition. TSN may correct any clerical or
typographical errors. All sales are subject to TSN's standard terms and conditions of sale.

LIMITED WARRANTY
TSN warrants its products to be free from defects in material or workmanship at the time of shipment. TSN standard catalog products are warranted for
adequacy of design when used in accordance with design limits in this document and properly specified and installed. This warranty excludes uses not
in compliance with specific applications and installation procedures set forth in this document. Warranty claims must be made by Purchaser in writing
within ninety (90) days of receipt of the Products.
All warranty obligations of TSN shall be limited, at the sole discretion of TSN, to repair or replace the defective product(s). These remedies shall consti-
tute TSN's sole obligation and sole remedy of purchaser under this warranty. In no event will TSN be responsible for incidental, consequential, indirect,
exemplary, incidental, special, consequential, or punitive damages, or other losses or damages however caused, including, but not limited to, instal-
lation costs, lost revenue or lost profits. TSN's liability for damages shall in no event exceed the applicable portion of the purchase price for defective
product(s).
Product defects that arise from acts of God, accidents, misuse, misapplication, improper installation, storage damage, negligence, or modification to
product(s) or its components are specifically excluded from this warranty. Product defects that arise from Purchaser providing incorrect information to
TSN, including but not limited to incorrect specifications such as incorrect dimensions, designs and/or loads, are also specifically excluded from this war-
ranty. TSN does not authorize any person or party to assume or create for it any other obligation or liability in connection with Products except as set
forth herein.
This Warranty is expressly in lieu of all other warranties, expressed or implied, including any warranties of merchantability or fitness for a particular pur-
pose, all such other warranties being hereby expressly excluded.

PATENTED TECHNOLOGY

VertiClip , VertiTrack , BridgeClip , BridgeBar , BuckleBridge , StiffClip , DriftClip , DriftTrak , DriftCorner , JamStud , StiffWall , SigmaStud ,


TightStrap , CircleTrak , PrimeWall and BackIt are trademarked products, and are patented or patent-pending technologies of TSN. Patent numbers
are: #5,904,023; #5,467,566; #5,906,080; #6,701,689; and #6,892,504. Numerous TSN design configurations are patented and/or patent pending and
are protected under US and International patent laws.

RETURN POLICY
TSN accepts returns on its standard catalog products under most circumstances. Customers must have TSN authorization prior to any returns. All
products must be in original boxes and have full count of pieces; opened boxes or containers cannot be returned. Modified or custom-made products,
including all products that have to be specifically cut, assembled, or otherwise produced for specific projects or applications, and specifically including

all stud, column, and StiffWall SW-S products, may not be returned for any reason other than warranty claims authorized in advance by TSN.
Customer must pay return freight to TSN. No products may be returned after 90 days from delivery. A 20% restocking and repackaging fee will be
charged.
CONTACT INFORMATION
DURHAM, NC LOCATION LAS VEGAS LOCATION
TSN Corporate Headquarters The Steel Network, Inc.
2012 TW Alexander Drive 6625 Arroyo Springs Street
PO Box 13997 Suite 140
Durham, NC 27709 Las Vegas, NV 89113
Phone: (919) 845-1025 Phone: (702) 643-4330
Fax: (888) 474-4877 Fax: (702) 643-4331
Web Site: www.steelnetwork.com
E-mail: tsn@steelnetwork.com
Toll Free Nationwide Phone
(888) 474-4876
Copyright 2010 The Steel Network Inc. All rights reserved. No part of this publication may be reproduced in whole or in part by any method without the
prior written consent of The Steel Network, Inc.

Toll Free Nationwide Phone (888) 474-4876 Raleigh, NC : Phone (919) 845-1025
Jan 2010 36
www.steelnetwork.com Las Vegas, NV : Phone (702) 643-4330

You might also like