You are on page 1of 606

High-Performance

Process Manager
Parameter Reference Dictionary
HP09-640

Implementation
High-Performance Process Manager - 2

High-Performance
Process Manager
Parameter Reference
Dictionary
HP09-640
11/99

Notices and Trademarks

Copyright 1999 by Honeywell Inc.


November 3, 1999

While this information is presented in good faith and believed to be accurate, Honeywell disclaims the
implied warranties of merchantability and fitness for a particular purpose and makes no express
warranties except as may be stated in its written agreement with and for its customer.

In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The
information and specifications in this document are subject to change without notice.

Honeywell and TotalPlant are U.S. registered trademarks of Honeywell Inc.


Fieldbus Foundation and FOUNDATION are trademarks of the Fieldbus Foundation.
Other brand or product names are trademarks of their respective owners.

iv

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

About This Publication


This publication defines the parameters for the HPM data point types implemented through
TotalPlant Solution (TPS) system network Release 610. This publication consists of two parts.
The first part contains parameter definitions for the 8-character TPS parameters of the NIM,
HPM, and fieldbus IOP. The second part, which begins in Section 6 of this publication, contains
parameter definitions for the fieldbus and the relevant TPS Builder parameters.
A parameter cross-reference listing is contained in Section 5. The cross-reference listing
contains two different parameter lists; TPS parameters versus fieldbus parameters, and fieldbus
parameters versus TPS parameters.
TPS is the evolution of TDC 3000X.

Due to the number of changes made to this document, change bars have not been used.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

vi

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Contents
1 INTRODUCTION ......................................................................................................................................9
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9

Purpose ............................................................................................................................................9
Use Of This Publication ....................................................................................................................9
Parameter Definition Format.............................................................................................................9
Parameters Per Point Type And AlgorithM Type............................................................................14
Full Points And Component Points .................................................................................................14
Abbreviations ..................................................................................................................................15
Fieldbus Mapped, Projected, and converted parameters ...............................................................17
CL Access (Non-Fieldbus Parameters) ..........................................................................................22
CL Access (Fieldbus Parameters) ..................................................................................................23

2 PARAMETERS PER POINT TYPE.........................................................................................................27


2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
2.19

Analog Input (AI).............................................................................................................................27


Analog Output (AO) ........................................................................................................................27
Array ...............................................................................................................................................28
Box (HPM Box) ..............................................................................................................................28
Box Flag..........................................................................................................................................29
Box Numeric ...................................................................................................................................29
Box Timer .......................................................................................................................................29
Device Control (DevCtl) ..................................................................................................................30
Digital Composite (DigComp) .........................................................................................................32
Digital Input (DigIn)........................................................................................................................33
Digital Output (DigOut) ..................................................................................................................33
FBCM (Function & Transducer Block Control Module) .................................................................34
IOP ................................................................................................................................................35
Logic..............................................................................................................................................35
PECM (Physical Entity Control Module)........................................................................................36
Process Module (ProcMod)...........................................................................................................36
SECM (Segment Entity Control Module).......................................................................................37
UCN Network ................................................................................................................................37
UCN Node.....................................................................................................................................37

3 PARAMETERS PER ALGORITHM TYPE..............................................................................................39


3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
3.19
3.20
R610
11/99

Auto Manual (AutoMan)..................................................................................................................39


Calculator (Calcultr) ........................................................................................................................39
Data Acquisition (DataAcq).............................................................................................................40
Flow Compensation (FlowComp) ...................................................................................................40
General Linearization (GenLin).......................................................................................................41
High-Low Average (HiLoAvg) .........................................................................................................41
Incremental Summer (IncrSum)......................................................................................................42
Middle-of-3 (MidOf3).......................................................................................................................42
Multiply/Divide (MulDiv) ..................................................................................................................43
Override Selector (ORSel) ............................................................................................................43
Pid .................................................................................................................................................44
Pid with External Reset Feedback (PidErfb) .................................................................................45
Pid with Feed Forward (PidFf) ......................................................................................................46
PID Position Proportional (PidPosPr)............................................................................................47
Position Proportional (PosProp) ....................................................................................................48
Ramp Soak (RampSoak) ..............................................................................................................49
Ratio Control (RatioCtl) .................................................................................................................50
Summer (RegCtl) ..........................................................................................................................51
Summer (RegPV) ..........................................................................................................................51
Switch............................................................................................................................................52
HPM Parameter Reference Dictionary
Honeywell Inc.

3.21 Totalizer (Totalizr) .........................................................................................................................52


3.22 Variable Dead Time with Lead/Lag (VdtLdLag) ............................................................................53
4 HPM Parameter Definitions ($ Through Y) ..................................................................................55
5 Fieldbus And TPS Parameter Cross-references..............................................................................437
5.1 TPS/Fieldbus Cross-Reference LIST ...........................................................................................437
5.2 Fieldbus/TPS Cross-Reference LIST ...........................................................................................442
6 Fieldbus Parameters Introduction ....................................................................................................447
6.1 Parameter Definition Format.........................................................................................................447
6.2 Fieldbus Structured Data Types ...................................................................................................451
6.2.1 Value & Status - Floating Point Structure....................................................................................451
6.2.2 Value & Status - Discrete Structure.............................................................................................451
6.2.3 Scaling Structure .........................................................................................................................451
6.2.4 Mode Structure............................................................................................................................452
6.2.5 Access Permissions ....................................................................................................................452
6.2.6 Alarm Float Structure ..................................................................................................................452
6.2.7 Event Update Structure ...............................................................................................................452
6.2.8 Alarm Summary Structure ...........................................................................................................453
6.2.9 FB LINK STructure......................................................................................................................453
6.2.10 Test Structure............................................................................................................................453
6.2.11 VFD Preference Entry Structure................................................................................................454
6.2.12 FB Start Entry Structure ............................................................................................................454
7 Supported Function and Transducer Blocks/Network management and System Management
Parameters ...............................................................................................................................................455
7.1 Parameters Per Supported Function Block (AI, PID, AO) ............................................................455
7.1.1 Analog Input Function Block Parameters ....................................................................................455
7.1.2 PID Function Block Parameters ..................................................................................................455
7.1.3 Analog Output Function Block Parameters .................................................................................455
7.2 Parameters Per Supported Transducer Block Parameter ............................................................456
7.2.1 Standard Advanced PositionER Valve Basic Device Example ...................................................456
7.2.2 Standard Temperature with Calibration Basic Device Access ....................................................456
7.2.3 Standard Pressure with Calibration Basic Device Access...........................................................457
7.3 Schedule Parameters ...................................................................................................................458
7.4 Network Management Parameters ...............................................................................................460
7.4.1 Network Management Directory Entry ........................................................................................460
7.4.3 DlmeLinkSettings ........................................................................................................................462
7.4.4 MaxTokenHoldTimeArray............................................................................................................462
7.4.5 VcrStaticEntry..............................................................................................................................463
7.4.6 DlmeLinkMasterInfo ....................................................................................................................466
7.4.7 PlmeBasicInfo .............................................................................................................................468
7.5 System Management Parameters ................................................................................................469
7.5.1 System NETwork Management Parameters ...............................................................................470
7.6 VFD Application Parameters ...........................................................................................................471
8 Fieldbus Parameter Definitions (A through X) .........................................................................473
Appendix A Enumerations ..................................................................................................................589

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INTRODUCTION

1.1 PURPOSE
This publication defines the user-visible parameters that exist in the TotalPlant Solution (TPS)
system Network Interface Module (NIM), High-Performance Process Manager (HPM), and
fieldbus. It also provides listings of parameters that are applicable to various HPM point types
and algorithms, including fieldbus points.
For information on how the TPS 8-character parameters are related to each other in terms of
point types and algorithms, refer to the High-Performance Process Manager Control Functions
and Algorithms manual in the Implementation/High-Performance Process Manager - 1 binder.
For information about fieldbus parameter relationships, refer to the TPS Fieldbus Overview
manual.
1.2 USE OF THIS PUBLICATION
Use this publication during configuration and during operation when detailed information about
NIM, HPM, or fieldbus parameters is required.
For use in data-point configuration for all point types (except fieldbus points), this publication
provides definitions for the parameter entries that can be made using the Parameter Entry
Displays (PEDs) of the Universal Station (US) or the PEDs available through the Native
Window of the Global User Station (GUS). For use in fieldbus data point configuration, this
publication provides definitions for the parameter entries that can be made using the TPS
Builder.
For use in process operation, this publication provides information about the HPM and fieldbus
data point parameters that appear in on-process displays such as the group and detail displays
1.3 PARAMETER DEFINITION FORMAT
In this dictionary, the parameter definitions are listed in alphabetical order according to the
parameter name. Each 8-character TPS parameter in this publication is defined using the general
format shown below for the ALMOPT parameter. The eight-character TPS fieldbus parameter
definitions are almost exactly the same excet that the fieldbus parameter descriptions also contain
an FF Param Source descriptor in the definition. FFMODEP is an example of the second type,
called a fieldbus parameter. The following paragraphs describe the entries that appear within
each parameter definition.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

INTRODUCTION

ALMOPT (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

e($ALMOPT) Alarming OptionDefines the alarming option for a digital input point whose
DITYPE is Status.
Eng/PB
None
APM
0-None (No alarms are to be detected)
1-Offnorml (Off Normal; alarm if current PV state is not the PVNORMAL state. PVNORMAL is
defined by the STATETXT(0) or STATETXT(1) descriptor, as configured by the user.)
2-ChngofSt (An alarm is generated when the digital input changes state in either direction).
Helpful Hint: ALMOPT configuration requires DITYPE = Status.

FFMODEP (PECM, FBCM)


FF Param. Source:
MODE_BLK.Permitted
Type:
Integer
Mode PermittedDefines the permitted modes of the resource or
function block (CM point).
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 0 to 255 (e.g., OOS=1, Man=8, OOS+Man=9, Auto=16, OOS+Man+Auto=25,)

For many parameters, the function of the parameter is described using the long name of the
parameter (Alarm Option), followed by a description as shown in the above example. Some
parameters in this dictionary do not have functional descriptions following the long name; this is
because the long name of the parameter sufficiently describes the parameter function.

10

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INTRODUCTION

FF Param. Source
Some control module (CM) parameters in the fieldbus Segment Entity Control Module (SECM),
Physical Entity Control Modue (PECM), and Function Block Control Module (FBCM) data
points contain traditional TPS 8-character parameters that are mapped to a fieldbus parameter.
Some CM parameters are projected directly from a fieldbus parameter, and some CM parameters
have no correlation to a fieldbus parameter. If the parameter is related to a fieldbus parameter,
this field contains the name of the fieldbus parameter.

Type
This entry is the data type that defines how the parameter is viewed by the system. The following
data types are used in this dictionary
BlindA literal byte string that appears exactly as it was written at the source. No
translations are made.
E:Enumeration; the value for the parameter is chosen from a set of predefined character
strings. In the above example, the enumerations of $ALMOPT are None, Offnorml.
SD_ENM:Self-Defining Enumeration; the value for the parameter is chosen from the userdefined character strings.
Ent.Prmconsists of a 1-16 character tag name, a period, and a 1-8 character parameter
name.
Ent_Id Tag name for a point.
Integera 16-bit whole number that does not contain a decimal point (+ 32767).
Logicala binary type with the values of ON (True) and OFF (False), or 0 (Off) and 1 (On).
NaNalthough not a data type, is used to represent "Not A Number" and is stored in IEEE
format.
Prm_Id1-8 character parameter name.
Reala 32-bit floating-point number in IEEE format.
String_La character string of maximum length = L. Same as Ascii_L.
TimeThe time of day in one of the following formats: DDD HH:MM:SS for duration, and
DDMMYY HH:MM:SS for an absolute date or time stamp.
Universal Ent.PrmUniversal Entity Parameter Identifier. It is basically the same as
Ent.Prm, but the entity name can be entered as an external 16-character tag name or as the
HPM's internal hardware reference address. The hardware reference address syntax can be
used to access parameters of points (within this same HPM) that are untagged or tagged.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

11

INTRODUCTION

The following are examples of hardware reference addresses*:


Type

Hardware Reference Address

AO Processor Output

!AO11S03.OP (Parameter OP of Slot #3 of AO processor #11)

DI Processor PV

!DI05S07.PVFL (Parameter PVFL of Slot #7 of DI processor #5)

DO Processor
Status Output

!DO15S12.SO (Parameter SO of Slot #12 of DO processor #15)

DO Processor
ON Pulse Command

!DO15S12.ONPULSE (Parameter ONPULSE of Slot #12 of DO


processor #15)

DO Processor
OFF Pulse Command

!DO15S12.OFFPULSE (Parameter OFFPULSE of Slot #12 of


DO processor #15)

Lock
The access lock defines "who" or "what" can change the parameter's value or option and the
access level defines "who" or "what" is requesting a parameter value or option change. For
example, if a requestor with an access level of Supr tries to change a parameter that has an access
lock of Engr, the request will be denied. The two charts below describe how access levels and
access locks work.
Access Level

Used By Who Or What When A


Parameter Change Request Is Made

Oper
Supr or Sup
Engr, Eng, or Eg
Cont
OnProc
HPMMCc
Prog
PtBld or PB
Configurable

Operator
Supervisor
Engineer
Continuous_Control (from a Module on the LCN)
On Process
HPMM_Continuous_Control (from HPMM)
CL/HPM Sequence_Programs
Point_Builder (Data Entity Builder)
TPS Builder

Access Lock

Access Level of Requestors That Can Change The Parameter

Oper
Supr
Engr
OnProc
Sup/Eg
EngOnly
Prog
Eng/PB
PtBld
View (Read Only)
Configurable

Oper

Supr
Supr

Oper

Supr
Supr

Engr
Engr
Engr
Engr
Engr
Engr
Engr

Cont
Cont
Cont

HPMMCc ProgPtBld
HPMMCc ProgPtBld
HPMMCc ProgPtBld

Cont

HPMMCc ProgPtBld
PtBld
PtBld

Depends on manufacturers mapped parameters or on fieldbus


parameters not already mapped.

______________
*The Analog Input address !AImmSss.Parameter is not supported because the Analog Input point does not have a useable
default database.

12

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INTRODUCTION

Default
The default for the parameter is the default value assigned by the system. The system
automatically enters the default value for a parameter when a range or a selection is not entered
for a parameter during point building. The default values are also shown on the configuration
forms and parameter entry displays.
PtRes
This defines where the parameter physically resides. The following residency locations are used
in the parameter definitions:
PtRes

Definition

HPM
NIM
SI
FF Device
IOP

High-Performance Process Manager


Network Interface Module
Serial Interface
FOUNDATION Fieldbus Device
Input/Output Processor

Range
This defines the range of the value that can be entered for this parameter. Integers that precede
HPM resident enumeration parameters are sometimes needed by advanced CL
users. These integers specify the members position within the set (that is, the ordinal). CL
programs external to the UCN (such as AM/CL) will see the same enumeration strings, but in
some cases, with different ordinal values.
Helpful Hint
Some parameter definitions contain a Helpful Hint box at the end of the definition. This box
contains additional information about the parameter, such as prerequisites, etc.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

13

INTRODUCTION

1.4 PARAMETERS PER POINT TYPE AND ALGORITHM TYPE


In addition to the parameter definitions, this dictionary also contains listings of the parameters
that are applicable to each HPM point type and algorithm type. Parameters-per-point-type are
defined in Section 2; parameters-per-algorithm-type are defined in Section 3.
1.5 FULL POINTS AND COMPONENT POINTS
Separate functional elements of the HPM are used to implement various parts of typical control
loops and control strategies. Each of these functional elements can be assigned a user-defined
tag name to allow for location-independent reference to the data associated with that function.
For example, point tags are assigned by the user for analog input and analog output slots.
The I/O Processor data (engineering-unit range for inputs, characterization option for outputs,
etc.) is configured as part of the point-build process for these points. A separate tag is configured
for each regulatory control (RegCtl) slot that is linked to the assigned analog I/O tags through
input/output connections.
The HPM provides a configurable parameter called PNTFORM (Point Form) that allows the user
to define which points are to be used as the primary operator interface for point data. The
PNTFORM parameter provides the user with two choices for point form: "Full" and
"Component." Points that are configured as having "Full" point form include alarm-related
parameters and sometimes, some other miscellaneous parameters. This information is needed
when the point is to be used as the primary operator interface to the point's data.
Points that are configured as having "Component" point form should be used to provide inputs
to the "Full" point and also for those points that handle the outputs from the "Full" points.
"Component" points should be used as part of the "Full" point that has been designated a primary
operator interface point.

14

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INTRODUCTION

1.6 ABBREVIATIONS
AM
AnalgIn
AnalgOut
AO
HPM

Application Module
Analog Input Data Point
Analog Output Data Point
Analog Output
High-Performance Process Manager

HPMM

High-Performance Process Manager Module

HPM Box

HPM Box Data Point

Array

Array Data Point

AutoMan
Box
Calcultr
CM
CM
DevCtl
DI
DigComp
DigIn
DigOut

Auto Manual algorithm


Box Data Point
Calculator algorithm
Computing Module 50 or 60
Control Module
Device Control Data Point
Digital Input
Digital Composite Data Point
Digital Input Data Point
Digital Output Data Point

DISOE

Digital Input Sequence of Events

DO

Digital Output

ESI

Extended Standard International Engineering Units

FBCM

Function Block Control Module

FBus

Fieldbus

FF

FOUNDATION Fieldbus

Flag

Flag Data Point

FlowComp Flow Compensation algorithm


FTA

Field Termination Assembly

GenLin

General Linearization algorithm

HiLoAvg
HLAI
IncrSum
IOL
IOP
Logic

High Low Average algorithm


High Level Analog Input
Incremental Summer algorithm
I/O Link
I/O Processor
Logic Data Point (Slot)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

15

INTRODUCTION

16

LCN
LLAI
LLMUX
MidOf3
MulDiv
NIM
ORSel

Local Control Network


Low Level Analog Input (or LLAI-8)
Low Level Analog Input Multiplexer (or LLAI-16/32)
Middle-of-3 Selector algorithm
Multiply Divide algorithm
Network Interface Module
Override Selector algorithm

PECM

Physical Entity Control Module

PI
Pid
PidErfb
PidFf
PidPosPr
PosProp
ProcMod
PSDP
RampSoak
RatioCtl
RegCtl
RegPV
RHMUX

Pulse Input
Proportional, Integral, Derivative,
Proportional, Integral, Derivative with External Reset Feedback algorithm
PID with Feedforward algorithm
PID With Position Proportional algorithm
Position Proportional algorithm
Process Module Data Point
Processor Status Data Point
Ramp Soak algorithm
Ratio Control algorithm
Regulatory Control Data Point or algorithm
Regulatory PV Data Point or algorithm
Remote Hardened Analog Input Multiplexer (or RHMUX16/32)

SECM

Segment Entity Control Module

SI
SDI
STI
Switch
Summer
Timer
Totalizr
UCN
VdtLdLag

Serial Interface
Serial Device Interface
Smart Transmitter Interface
Switch algorithm
Summer algorithm
Timer Data Point
Totalizer algorithm
Universal Control Network
Variable Deadtime Lead Lag algorithm

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INTRODUCTION

1.7 FIELDBUS MAPPED, PROJECTED, AND CONVERTED PARAMETERS


The following three methods are used for changing fieldbus parameters to TPS Network
parameters:

Parameter Mapping
Parameter Projection
Parameter Conversion

1.7.1 Parameter Mapping


In the parameter mapping method, a fieldbus parameter or some part of a fieldbus parameter is
made a TPS Network parameter with traditional TPS Network meaning. For example, fieldbus
parameter OUT.Status for an analog input point maps to TPS Network parameter
PVAUTOST.
The mapped parameters are listed in Table 1-1.
Table 1-1 Mapped Parameters
TPS Parameter
$BKCLOUD
$BKCLOUT
$BKCLSEL1
$BKCLSEL2
$BKCLSEL3
$RBREC
$RCASOUD
$RCASOUT
$ROUTOUT
ALMINFO
BADPVFL
BLKERRFL
CASIN
CASIND
CVEUHI
CVEULO
DCFAILFL
DEVHIFL
DEVHIPR
DEVHITP
DEVLOFL
DEVLOPR
DEVLOTP
DISCFL
INPTDIR
LASTPV
MODE
MODEAPPL

R610
11/99

Fieldbus Parameter Source


BKCAL_OUT_D
BKCAL_OUT
BKCAL_SEL1
BKCAL_SEL2
BKCAL_SEL3
READBACK_D
RCAS_OUT_D
RCAS_OUT
ROUT_OUT
None
AI: OUT.Status
BLOCK_ERR
CAS_IN
CAS_IN_D
PID: OUT_SCALE.EU100
PID: OUT_SCALE.EU0
FAIL
ALARM_SUM.Current
DV_HI_PRI
DV_HI_LIM
ALARM_SUM.Current
DV_LO_PRI
DV_LO_LIM
ALARM_SUM.Current
Bit 0 of IO_OPTS (Invert)
AI: OUT.Value; PD, PID:PV.Value
Writes: MODE_BLK.Target. Reads: MODE_BLK.Actual
MODE_BLK.Permitted

HPM Parameter Reference Dictionary


Honeywell Inc.

Residency
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
NIM
IOP
IOP
NIM
IOP
IOP
IOP
IOP
IOP
IOP

17

INTRODUCTION

Table 1-2 Mapped Parameters, continued


TPS Parameter
MODEBLKC
NMODE
OFFNRMPR
OP
PTINAL
PV
PVALDBEU
PVAUTO
PVAUTOST
PVCALC
PVEUHI
PVEULO
PVFL
PVFORMAT
PVHHFL
PVHHPR
PVHHTP
PVHIFL
PVHIPR
PVHITP
PVLLFL
PVLLPR
PVLLTP
PVLOFL
PVLOPR
PVLOTP
PVP
PVRAW
PVSTS
RCASIN
RCASIND
ROUTIN
SEL1
SEL2
SEL3
SLOTSFBT
SO
SP
SPFORMAT
SPP

18

Fieldbus Parameter Source


MODE_BLK.Actual + MODE_BLK.Target
Mode_Blk.Normal
DISC_PRI
AO, PID: OUT.Value
ALARM_SUM.Current + for AI, OUT.Status
AI: OUT.Value; DI: OUT_D.Value; PD, PID: PV.Value
ALARM_HYS
AI: OUT.Value; DI: OUT_D.Value
AI: OUT.Status
AI: Field_Val.Value
AI: OUT_SCALE.EU100; PID: PV_SCALE.EU100
AI: OUT_SCALE.EU0; PID: PV_SCALE.EU0
DI: OUT_D.Value
AI: OUT_SCALE.DecPt; PID: PV_SCALE.DecPt
ALARM_SUM.Current
HI_HI_PRI
HI_HI_LIM
ALARM_SUM.Current
HI_PRI
HI_LIM
ALARM_SUM.Current
LO_LO_PRI
LO_LO_LIM
ALARM_SUM.Current
LO_PRI
LO_LIM
AI: OUT.Value; PID: PV.Value
AI: FIELD_VAL.Value; DI: FIELD_VAL_D.Value
AI: OUT.Status; PID: PV.Status
RCAS_IN
RCAS_IN_D
ROUT_IN
SEL_1
SEL_2
SEL_3
None
DO: OUT_D.Value
AO, PID: SP.Value
AO, PID: PV_SCALE.DecPt
PID: SP.Value

HPM Parameter Reference Dictionary


Honeywell Inc.

Residency
IOP
IOP
NIM
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
NIM
IOP
IOP
NIM
IOP
IOP
NIM
IOP
IOP
NIM
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP
IOP

R610
11/99

INTRODUCTION

1.7.2 Projected Parameters


In the parameter projection method, the fieldbus parameter or a single member of a fieldbus
structure is made available in its native form as a TPS Network parameter. For example, fieldbus
parameter GAIN is projected to TPS Network parameter FFGAIN.
The projected parameters are listed in Table 1-2.
Table 1-2 Projected Parameters
TPS Parameter
DISCPR
DISCST
FFALMCUR
FFBCINST
FFBCINVL
FFBCOPST
FFBCOPVL
FFCSIDST
FFCSIDVL
FFCSINST
FFCSINVL
FFDVHILM
FFDVHIPR
FFDVLOLM
FFDVLOPR
FFFFDECP
FFFFGAIN
FFFFS0
FFFFS100
FFFFUIDX
FFFFVLST
FFFFVLVL
FFGAIN
FFHHLM
FFHHPR
FFHILM
FFHIPR
FFINSTS
FFINVAL
FFLLLM
FFLLPR
FFLOLM
FFLOPR
FFMODEA
FFMODEN
FFMODEP
FFMODET

R610
11/99

Fieldbus Parameter Source


DISC_PRI
DISC_LIM
ALARM_SUM.Current
BKCAL_IN.Status
BKCAL_IN.Value
BKCAL_OUT.Status
BKCAL_OUT.Value
CAS_IN_D.Status
CAS_IN_D.Value
CAS_IN.Status
CAS_IN.Value
DV_HI_LIM
DV_HI_PRI
DV_LO_LIM
DV_LO_PRI
FF_SCALE.DecPt
FF_GAIN
FF_SCALE.EU0
FF_SCALE.EU100
FF_SCALE.UnitIndex
FF_VAL.Status
FF_VAL.Value
GAIN
HI_HI_LIM
HI_HI_PRI
HI_LIM
HI_PRI
IN.Status
IN.Value
LO_LO_LIM
LO_LO_PRI
LO_LIM
LO_PRI
MODE_BLK.Actual
MODE_BLK.Normal
MODE_BLK.Permitted
MODE_BLK.Target

Residency
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE

HPM Parameter Reference Dictionary


Honeywell Inc.

19

INTRODUCTION

Table 1-2 Projected Parameters, continued


TPS Parameter
FFOEXPST
FFOEXPVL
FFOPDECP
FFOPHILM
FFOPLOLM
FFOPS0
FFOPS100
FFOPUIDX
FFOREMST
FFOREMVL
FFOUT1ST
FFOUT1VL
FFOUT2ST
FFOUT2VL
FFOUTAST
FFOUTAVL
FFOUTDST
FFOUTDVL
FFOUTSTS
FFOUTVAL
FFPTRPST
FFPTRPVL
FFPVDECP
FFPVS0
FFPVS100
FFPVSTS
FFPVUIDX
FFPVVAL
FFRATE
FFRBDST
FFRBST
FFRCIDST
FFRCIDVL
FFRCINST
FFRCINVL
FFRCOPST
FFRCOPVL
FFRESET
FFROINST
FFROINVL
FFROOPST
FFROOPVL
FFSEL1ST
FFSEL1VL

20

Fieldbus Parameter Source


OUT_EXP.Status
OUT_EXP.Value
OUT_SCALE.DecPt
OUT_HI_LIM
OUT_LO_LIM
OUT_SCALE.EU0
OUT_SCALE.EU100
OUT_SCALE.UnitIndex
OUT_REM.Status
OUT_REM.Value
OUT_1.Status
OUT_1.Value
OUT_2.Status
OUT_2.Value
OUT_ACCUM.Status
OUT_ACCUM.Value
OUT_D.Status
OUT_D.Value
OUT.Status
OUT.Value
OUT_PTRIP.Status
OUT_PTRIP.Value
PV_SCALE.DecPt
PV_SCALE.EU0
PV_SCALE.EU100
PV.Status
PV_SCALE.UnitIndex
PV.Value
RATE
READBACK_D.Status
READBACK.Status
RCAS_IN_D.Status
RCAS_IN_D.Value
RCAS_IN.Status
RCAS_IN.Value
RCAS_OUT.Status
RCAS_OUT.Value
RESET
ROUT_IN.Status
ROUT_IN.Value
ROUT_OUT.Status
ROUT_OUT.Value
SEL_1.Status
SEL_1.Value

Residency
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INTRODUCTION

Table 1-2 Projected Parameters, continued


TPS Parameter
FFSEL2ST
FFSEL2VL
FFSEL3ST
FFSEL3VL
FFSPHILM
FFSPLOLM
FFSPRTDN
FFSPRTUP
FFSPSTS
FFSPVAL
FFSTREV
FFTRDIST
FFTRDIVL
FFTRIPST
FFTRIPVL
FFTRVLST
FFTRVLVL
FFXDDECP
FFXDS0
FFXDS100
FFXDUIDX
FLOAT
IN
IND
OUT
OUTD
OUTDST
OUTST
READBACK
READBAKD
RSSTATE
SIMDST
SIMDVL
SIMDXST
SIMDXVL
SIMENBL
SIMSTAT
SIMVAL
SIMXSTAT
SIMXVAL
US16
US8
VS

R610
11/99

Fieldbus Parameter Source


SEL_2.Status
SEL_2.Value
SEL_3.Status
SEL_3.Value
SP_HI_LIM
SP_LO_LIM
SP_RATE_DN
SP_RATE_UP
SP.Status
SP.Value
ST_REV
TRK_IN_D.Status
TRK_IN_D.Value
OUT_TRIP.Status
OUT_TRIP.Value
TRK_VAL.Status
TRK_VAL.Value
XD_SCALE.DecPt
XD_SCALE.EU0
XD_SCALE.EU100
XD_SCALE.UnitIndex
User configured
Configurable via link object
Configurable via link object
Configurable via link object
Configurable via link object
Configurable via link object
Configurable via link object
READBACK.Value
READBACK_D.Value
Resource block: RS_STATE
SIMULATE.Simulate Status
SIMULATE.Simulate Value
SIMULATE.Transducer Status
SIMULATE.Transducer Value
SIMULATE.Simulate En/Disable
SIMULATE.Simulate Status
SIMULATE.Simulate Value
SIMULATE.Transducer Status
SIMULATE.Transducer Value
User configured
User configured
User configured

Residency
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
IOP
IOP
IOP
IOP
IOP
IOP
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
IOP
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
IOP
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE
FF DEVICE

HPM Parameter Reference Dictionary


Honeywell Inc.

21

INTRODUCTION

1.7.2 Parameter Conversion


The parameter conversion method is similar to parameter mapping, but some amount of
calculation is necessary between the fieldbus entity and the TPS Network entity.

1.8 CL ACCESS (NON-FIELDBUS PARAMETERS)


1.8.1 Parameter Not Accessible to CL
Parameter $EVNTREC is not accessible to Control Language (CL) sequences.
1.8.2 CL Restricted Parameters
The following parameters are not accessible to CL/HPM sequences. They are not directly
available to CL/AM sequences. Access to CL/AM is through a custom data segment parameters
attached to AM regulatory points as described below.
BHALMFL1-BHALMFL7
NODESTS
NODETYP
UCNRECHN
These parameters are available to user schematics using the NIM reserved data point, e.g.,
$NMuuBnn.param, where uu = UCN number and nn = UCN node number.
CL/AM programs can access the restricted parameters as Regulatory Point General inputs (using
ordinary point parameter access). They must be transferred to parameters of AM regulatory
points. There are two ways to do this:
1. Boolean parameters (BHALMFLn), can be referenced as general inputs to a Switch
algorithm. A CL program can access the switch parameters.
2. For Enumerations (NODEOPER, NODESTS, NODETYP, POSITION, AND UNRECHN) a
custom data segment is created to allow the parameters to be referenced as general inputs and
transferred to user-defined parameters (of a RegCtl Point) that can be accessed by CL.

22

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INTRODUCTION

1.9 CL ACCESS (FIELDBUS PARAMETERS)


This section describes the HPM fieldbus parameters that are supported by CL/AM and CL/HPM.
1.9.1 HPM Fieldbus Parameters Supported by CL/AM
There are restrictions when accessing parameters in the SECM, PECM, and FBCM fieldbus
points using CL/AM. The parameters for fieldbus points are arranged into three classes that are
designated as class A, class B, and class C, and the following CL/AM restrictions are based on
these parameter classes.

Class A parameters are fieldbus IOP parameters that are contained in the fieldbus IOP. Read
and write requests for these parameters are directed to the fieldbus IOP database.

Class B parameters are fieldbus-device parameters that are cached (and possibly mapped) in
the fieldbus IOP. Read requests for these parameter values are directed to the IOP database.
Write requests are directed to the fieldbus device.

Class C parameters are fieldbus-device parameters that are not cached in the fieldbus IOP.
Read and write requests for these parameter values are directed to the fieldbus device.

CL/AM programs can control the timing of fieldbus parameter access through the
BACKGROUND insertion point. Access to fieldbus parameters through a foreground CL/AM
program could delay the program and cause processor overruns or use fieldbus data that is old.
When creating CL/AM programs that use HPM fieldbus parameters, note that all CL/AM write
operations to class B parameter values and all CL/AM read and write operations to class C
parameter values must be delayed. This delay should be approximately twice the execution
period of the fieldbus function block as specified by the link active schedule of the fieldbus
segment.
Read operations to class B parameter values are immediate. However, the value that is read back
may not be the current value. The parameter values are not synchronously updated with the
CL/AM execution period.
CL/AM access to the HPM fieldbus parameters is further restricted based on the access lock and
the data type of each parameter. The access lock and data type are listed within the description
of each parameter in this document.
The following listing contains the HPM fieldbus parameters that are supported by CL/AM. For
ease of use, each parameter name in the listing is followed by a letter (A, B, or C) that designates
the respective parameter class.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

23

INTRODUCTION

ACTSCHVR (B)
ACTVSCHD (A)
AKVCRIDX (A)
BRDP (C)
CASIN (A)
CASIND (A)
CFLNKSET (A)
DEFPDTAG (A)
DEVDTLST (A)
DEVID (A)
FBSCHOBJ (A)
FFDEVREV (A)
FFDVLOLM (B)
FFDVLOPR (B)
FFERRMSG (A)
FFFFDECP (B)
FFFFGAIN (B)
FFFFS0 (B)
FFFFS100 (B)
FFFFUIDX (B)
FFFFVLST (B)
FFFFVLVL (B)
FFGAIN (B)
FFHHLM (B)
FFHHPR (B)
FFHILM (B)
FFHIPR (B)
FFINSTS (B)
FFINVAL (B)
FFLLLM (B)
FFLLPR (B)
FFLOLM (B)
FFLOPR (B)
FFMODEA (B)
FFMODEN (B)
FFMODEP (B)
FFMODET (B)
FFOEXPST (B)
FFOEXPVL (B)
FFOPDECP (B)
FFOPHILM (B)
FFOPLOLM (B)
FFOPS0 (B)
FFOPS100 (B)
FFOPUIDX (B)
FFOREMST (B)
FFOREMVL (B)
FFOUT1ST (B)

24

FFOUT1VL (B)
FFOUT2ST (B)
FFOUT2VL (B)
FFOUTAST (B)
FFOUTAVL (B)
FFOUTDST (B)
FFOUTDVL (B)
FFOUTSTS (B)
FFOUTVAL (B)
FFPTRPST (B)
FFPTRPVL (B)
FFPVDECP (B)
FFPVS0 (B)
FFPVS100 (B)
FFPVSTS (B)
FFPVUIDX (B)
FFPVVAL (B)
FFRATE (B)
FFRBDST (B)
FFRBST (B)
FFRCIDST (B)
FFRCIDVL (B)
FFRCINST (B)
FFRCINVL (B)
FFRCOPST (B)
FFRCOPVL (B)
FFRESET (B)
FFROINST (B)
FFROINVL (B)
FFROOPST (B)
FFROOPVL (B)
FFSEL1ST (B)
FFSEL1VL (B)
FFSEL2ST (B)
FFSEL2VL (B)
FFSEL3ST (B)
FFSEL3VL (B)
FFSPHILM (B)
FFSPLOLM (B)
FFSPRTDN (B)
FFSPRTUP (B)
FFSPSTS (B)
FFSPVAL (B)
FFSTREV (B)
FFTRDIST (B)
FFTRDIVL (B)
FFTRIPST (B)
FFTRIPVL (B)

FFTRVLST (B)
FFTRVLVL (B)
FFXDDECP (B)
FFXDS0 (B)
FFXDS100 (B)
FFXDUIDX (B)
FLOAT (C)
HBRDP (C)
IDXFLOAT (A)
IDXUS16 (A)
IDXUS32 (A)
IDXUS8 (A)
IDXVS (A)
IN (A)
IND (A)
INITREQ (A)
INPTDIR (B)
LASTPV (B)
LINKCMD (A)
LINKSTAT (A)
LIVELIST (A)
LNKDTLST (A)
LNKMASRE (A)
LOBJLIST (A)
LVLSTIDX (A)
MGCFGCMD (A)
MGCFGSTA (A)
MGDEVADR (A)
MGDEVID (A)
MGDEVREV (A)
MGINFIDX (A)
MGMODNAM (A)
MGPDTAG (A)
MGVCRIDX (A)
MGVENAME (A)
MODATTR (A)
MODE (B)
MODEBLKC (B)
MODEPERM (A)
MODNAME (A)
NBSCHOBJ (A)
NMODATTR (A)
NMODE (B)
NOASOC (A)
NUMPECMS (A)
NUMSCHD (B)
NUMVW3 (A)
NUMVW4 (A)

OP (B)
OUT (B)
OUTD (B)
OUTDST (B)
OUTST (B)
PDDTLST (A)
PDSTAT (A)
PDTAG (A)
PNTFORM (A)
PNTTYPE (A)
PRILNKMS (A)
PTEXECST (A)
PTINAL (A)
PV (B)
PVALDB (A)
PVALDBEU (B)
PVAUTO (B)
PVAUTOST (B)
PVCALC (B)
PVEUHI (B)
PVEULO (B)
PVEXEUHI (A)
PVEXEULO (A)
PVEXHIFL (A)
PVEXLOFL (A)
PVFL (A)
PVFORMAT(B)
PVHHFL (A)
PVHHTP (B)
PVHIFL (A)
PVHITP (B)
PVLLFL (A)
PVLLTP (B)
PVLOFL (A)
PVLOTP (B)
PVP (B)
PVRAW (A)
PVSTS (A)
PVTV (A)
PVTVP (B)
QUBODIDX (A)
QUBRATE (A)
RCASIN (A)
RCASIND (A)
READBACK (B)
READBAKD (B)
REDTAG (A)
REMDOPT (A)

HPM Parameter Reference Dictionary


Honeywell Inc.

RETCAS (A)
ROUTIN (A)
RSSTATE (B)
SCHDATA1 (A)
SCHDATA2 (A)
SCHDSIZE (A)
SCHDVER (B)
SEL1 (A)
SEL2 (A)
SEL3 (A)
SIMDST (C)
SIMDVL (A)
SIMDXST (C)
SIMDXVL (C)
SIMENBL (C)
SIMSTAT (C)
SIMVAL (A)
SIMXSTAT (C)
SIMXVAL (C)
SLOTSFBT (A)
SMCONFIG (A)
SMODIDX (A)
SMODOBJS (A)
SO (B)
SP (B)
SPFORMAT (B)
SPP (B)
STKCAPRE (A)
TBNMVW3 (A)
TBNMVW4 (A)
TBODIDX (A)
TBTYPE (A)
US16 (C)
US32 (C)
US8 (C)
USEVFDNO (A)
VCRLIST (A)
VFDREF (A)
VIEW2 (A)
VIEW3 (C)
VIEW4 (C)
VIEWOUT (B)
VS (C)
VWODIDX (A)
XVIEW2 (C)
XVIEW3 (C)
XVIEW4 (C)
XVWODIDX (A)

R610
11/99

1.9.2 HPM Fieldbus Parameters Supported by CL/HPM


There are restrictions when accessing parameters of SECM, PECM, and FBCM fieldbus points
using CL/HPM. In terms of CL/HPM usage, these parameters are classified into two categories:
read-only and read/write.
The read-only category indicates that CL/HPM can only read the value of the parameter. The
read/write category indicates that CL/HPM can read the parameter value and change the
parameter value.
CL/HPM access to the HPM fieldbus parameters is further restricted based on the access lock
and the data type of each parameter. The access lock and data type are listed within the
description of each parameter in this document.
The following listing contains the HPM fieldbus parameters that are supported by CL/HPM. For
ease of use, an abbreviation (R or R/W) that indicates whether the parameter access is read-only
or read/write follows each parameter name in the listing.
ACTSCHVR (R)
ACTVSCHD (R)
AKVCRIDX (R)
ALMINFO (R)
ALVCRIDX (R)
APPL (R)
APVCRIDX (R)
ASOCSLOT (R)
ASSOCCM (R)
BADPVFL (R)
BLKERRFL (R)
BLKODIDX (R)
BLKTAG (R)
CFGCMD (R)
CFGSTAT (R)
CMTYPE (R)
CONTCUT (R/W)
CVEUHI (R)
CVEULO ( R )
DCFAILFL (R)
DEFADDR (R)
DEVADDR (R)
DEVCLASS (R)
DEVHIFL (R)
DEVHITP (R)
DEVLOFL (R)
DEVLOTP (R)
DEVSTAT (R)
DISCFL (R)

R610
11/99

DISCPR (R)
DISCST (R)
DMNODIDX (R)
FBSCHVER (R)
FBTYPE (R)
FFALMCUR (R)
FFBCINST (R)
FFBCINVL (R)
FFBCOPST (R)
FFBCOPVL (R)
FFCSIDST (R)
FFCSIDVL (R)
FFCSINST (R)
FFCSINVL (R)
FFDVHILM (R)
FFDVHIPR (R)
FFDVLOLM (R)
FFDVLOPR (R)
FFFFDECP (R)
FFFFGAIN (R)
FFFFS0 (R)
FFFFS100 (R)
FFFFUIDX (R)
FFFFVLST (R)
FFFFVLVL (R)
FFGAIN (R)
FFHHLM (R)
FFHHPR (R)
FFHILM (R)

FFHIPR (R)
FFINSTS (R)
FFINVAL (R)
FFLLLM (R)
FFLLPR (R)
FFLOLM (R)
FFLOPR (R)
FFMODEA (R)
FFMODEN (R)
FFMODEP (R)
FFMODET (R)
FFOEXPST (R)
FFOEXPVL (R)
FFOPDECP (R)
FFOPHILM (R)
FFOPLOLM (R)
FFOPS0 (R)
FFOPS100 (R)
FFOPUIDX (R)
FFOREMST (R)
FFOREMVL (R)
FFOUT1ST (R)
FFOUT1VL (R)
FFOUT2ST (R)
FFOUT2VL (R)
FFOUTAST (R)
FFOUTAVL (R)
FFOUTDST (R)
FFOUTDVL (R)

FFOUTSTS (R)
FFOUTVAL (R)
FFPTRPST (R)
FFPTRPVL (R)
FFPVDECP (R)
FFPVS0 (R)
FFPVS100 (R)
FFPVSTS (R)
FFPVUIDX (R)
FFPVVAL (R)
FFRATE (R)
FFRBDST (R)
FFRBST (R)
FFRCIDST (R)
FFRCIDVL (R)
FFRCINST (R)
FFRCINVL (R)
FFRCOPST (R)
FFRCOPVL (R)
FFRESET (R)
FFROINST (R)
FFROINVL (R)
FFROOPST (R)
FFROOPVL (R)
FFSEL1ST (R)
FFSEL1VL (R)
FFSEL2ST (R)
FFSEL2VL (R)
FFSEL3ST (R)

HPM Parameter Reference Dictionary


Honeywell Inc.

FFSEL3VL (R)
FFSPHILM (R)
FFSPLOLM (R)
FFSPRTDN (R)
FFSPRTUP (R)
FFSPSTS (R)
FFSPVAL (R)
FFSTREV (R)
FFTRDIST (R)
FFTRDIVL (R)
FFTRIPST (R)
FFTRIPVL (R)
FFTRVLST (R)
FFTRVLVL (R)
FFXDDECP (R)
FFXDS0 (R)
FFXDS100 (R)
FFXDUIDX (R)
IN (R/W)
IND (R/W)
INITREQ (R)
INPTDIR (R/W)
LASTPV (R)
LINKCMD (R/W)
LINKSTAT (R)
LVLSTIDX (R)
MGCFGCMD (R)
MGCFGSTA (R)
MGDEVADR (R)

25

INTRODUCTION

MGINFIDX (R)
MGVCRIDX (R)
MODATTR (R/W)
MODE (R)
MODEPERM(R/W)
NBSCHOBJ (R)
NMODATTR (R/W)
NMODE (R)
NOASOC (R)
NUMPECMS (R)
NUMSCHD (R)
NUMVW3 (R)
NUMVW4 (R)
OP (R)
OUTD (R)
OUTDST (R)
OUT (R)
OUTST (R)
PDSTAT (R)
PNTFORM (R)
PNTTYPE (R)
PRILNKMS (R)
PTEXECST (R)
PTINAL (R)
PVALDB (R)
PVALDBEU (R)
PVAUTO (R)
PVAUTOST (R)
PVCALC (R)
PV (R)
PVEUHI (R)
PVEULO (R)
PVEXEUHI (R/W)
PVEXEULO (R/W)
PVEXHIFL (R)
PVEXLOFL (R)
PVFL (R/W)
PVFORMAT (R)
PVHHFL (R)
PVHHTP (R)
PVHIFL (R)
PVHITP (R)
PVLLFL (R)
PVLLTP (R)
PVLOFL (R)
PVLOTP (R)
PVP (R)
PVRAW (R)
PVSTS (R)

26

PVTV (R)
PVTVP (R)
QUBRATE (R)
READBACK (R)
READBAKD (R)
REDTAG (R/W)
REMDOPT (R)
RETCAS (R)
RSSTATE (R)
SCHDSIZE (R)
SCHDVER (R)
SIMDVL (R/W)
SIMVAL (R)/W
SLOTSFBT (R)
SMODIDX (R)
SMODOBJS (R)
SO (R)
SP (R)
SPFORMAT (R)
SPP (R)
TBNMVW3 (R)
TBNMVW4 (R)
TBODIDX (R)
TBTYPE (R)
USEVFDNO (R)
VFDREF (R)
VWODIDX (R)
XVWODIDX (R)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

2 PARAMETERS PER POINT TYPE


This section contains listings of parameters that are applicable to each data point type in the HPM, except
for the Regulatory Control and Regulatory PV data points which can be found in Section 3. Refer to
Sections $ - X for the definitions of the parameters.

2.1 ANALOG INPUT (AI)


The parameters of the Analog Input Data points are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
AVDELTHS
AVSTS
BADPVFL (F)
BADPVPR (F)
C1
C2
CJTACT
COMMAND
CONTCUT (F)
DAMPING
DECONF
EUDESC
HIGHAL (F)
HIGHALPR (F)
INPTDIR
KEYWORD
LASTPV

LOCUTOFF
LRL
LRV
MODNUM
NAME
NODENUM
NODETYP
NTWKNUM
OTDENBLE
OVERVAL (F)
PIUOTDCF
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PTDESC
PTEXECST
PTINAL

PV
PVALDB (F)
PVALDBEU (F)
PVAUTO
PVAUTOST
PVCALC
PVCHAR
PVCLAMP
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)

PVHITP (F)
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVRAW
PVRAWHI
PVRAWLO
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS

PVTV (F)
PVTVP (F)
RJTEMP
S1
SECVAR
SENSRTYP
SERIALNO
SFSTS
SLOTNUM
SLWSRCID
STATE
STI_EU
STISWVER
STITAG
TCRNGOPT
TF
TIMEBASE
UNIT
URL
URV

2.2 ANALOG OUTPUT (AO)


The parameters of the Analog Output Data point are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
ASSOCDSP
CASREQ (F)
EUDESC
KEYWORD
LOCALMAN
MODATTR (F)
MODE (F)
MODEAPPL (F)
MODEPERM (F)

R610
11/99

MODNUM
NAME
NMODATTR (F)
NMODE (F)
NODENUM
NODETYP
NTWKNUM
OP
OPCHAR

OPFINAL
OPIN0
OPIN1
OPIN2
OPIN3
OPIN4
OPIN5
OPOUT0
OPOUT1

OPOUT2
OPOUT3
OPOUT4
OPOUT5
OPTDIR
$OPTOL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE

HPM Parameter Reference Dictionary


Honeywell Inc.

PNTTYPE
PRIMMOD (F)
PTDESC
PTEXECST
RCASOPT
REDTAG (F)
RINITREQ (F)
SLOTNUM
STDBYMAN
UNIT

27

2 PARAMETERS PER POINT TYPE

2.3 ARRAY
The parameters of the Array Data Point are listed below in alphabetical order. The Point Form
parameter is set to Full.
AB_DATA1
AB_DATA2
AB_DATA3
AB_DATA4
ASSOCDSP
AUXDATA1
AUXDATA2
AUXDATA3
AUXDATA4
BADPVFL
CNFMU
CNFPU

DEVADDR
ERRCODE
EXTDATA
FL
FLDESC
FLSTIX
FTANUM
INITREQ
IOPNUM
KEYWORD
NFLAG

NN
NNDESC
NNUMERIC
NNSTIX
NODENUM
NODETYP
NSTRING
NTIME
NTWKNUM
OVERLAP
PERIOD

PNTFORM
PNTNODTY
PNTTYPE
PRIMMOD
PTDESC
SCANPRI
SLOTNUM
SPLOCK
STR8
STR16
STR32

STR64
STRDESC
STRLEN
STRSTIX
STSMSG
TIME
TIMEDESC
TIMESECS
TIMESTIX
UNIT
USERID

2.4 BOX (HPM BOX)


The parameters of the High-Performance Process Manager Box Data Point are listed below in
alphabetical order.
ASSOCDSP
BADPVTXT
CHPINOPR
CMFLTIME
CMIDTXT
CNFPU
CNFPUP
COMHOUR
COMMIN
CRIOLORN
CRPPXORN
CRUCNORN
CTFLTIME
CTIDTXT
CTLHOUR
CTLMIN
CTLOPT
CTLPATCH
CYCLETIM
DATE
DAY
DB_VALID
DIAGCMD
EUNDESC
FL
FRQUTAVG
FRQUTMAX
FRSPTAVG
FRSPTMAX

FTA1TYPE
FTA2TYPE
HOUR
IOLASTS
IOLBSTS
IOLCHAER
IOLCHASL
IOLCHBER
IOLCHBSL
IOLCHERT
IOLCMD
IOLHWREV
IOLPERSW
IOLREV
IOLVERS
IOMCARD
IOMCHAER
IOMCHASL
IOMCHBER
IOMCHBSL
IOMCMD
IOMCOMER
IOMFILE
IOMOPER
IOMREALT
IOMRECHN
IOMSEVER
IOMSTS
IOMTYPE
IONTOKEN

IOP
IOPIDAY
IOPIMON
IOPIYEAR
IOPNUM
IOPSTR1
IOPSTR2
IORECCHN
IOSSTS
IOSTKNDR
IOTKNSTL
LSIOLORN
LSPPXORN
LSUCNORN
MAXCNFPU
MDMHWREV
MINUTE
MNFASIC
MNFCCDAY
MNFDAY
MNFCCINF
MNFCCMTH
MNFCCSER
MNFCCYR
MNFFPGA
MNFIODAY
MNFIOINF
MNFIOMTH
MNFIOSER
MNFIOYR

MNFMDDAY
MNFMDINF
MNFMDMTH
MNFMDINF
MNFMDMTH
MNFMDSER
MNFMDYR
MONPER
MONTH
MOVPVTXT
MPCFWREV
MPCHWREV
NARRSLOT
NCTLSLOT
NDCSLOT
NDEVSLOT
NFASTCTL
NFASTDC
NFASTDEV
NFASTLOG
NFASTPV
NFLAG
NLOGSLOT
NN
NNUMERIC
NODEASSN
NODECMD
NODECONF
NODENUM
NODESTS
NODETYP

NODFSTAT
NOPTS
NORQUMAX
NORSPAVG
NORSPMAX
NOTRAAVG
NOTRAMAX
NPARAVG
NPARMAX
NPMSLOT
NPVSLOT
NSTRING
NTIME
NTIMER
NTRAAVG
NTRAMAX
PKGOPT
PMMCHAER
PMMCHASL
PMMCHBER
PMMCHBSL
PMMCMD
PMMCOMER
PMMCTLST
PMMOPER
PMMRECCH
PMMSEVER
PMMSFSTS
PMMSTS
PNTNODTY
POSITION

RELVERS
RELREV
RJTEMP
SAFOPCMD
SCANPER
SECOND
SEQPRGSZ
SRQUTAVG
SRSPTAVG
SRSPTMAX
STR8
SUMSLTSZ
SWTCHACT
TIERTYPE
TIME
TMCMD
TMPV
TMRV
TMSO
TMSP
TMST
TMTB
TRATAVG
TRATMAX
UTSDRIFT
UTSNODE
UTSTBCRV
UTSTIME
UTSTIMST
WEEKDAY
YEAR

Some of the parameters in the above listing are arrays and are not defined in this publication.

28

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

2 PARAMETERS PER POINT TYPE

2.5 BOX FLAG


The parameters of the Box Flag Data Point are listed below in alphabetical order. (F) indicates
that the parameter is applicable when the PNTFORM = Full; an * indicates that the parameter is
applicable to flag slots 1-128.
$AUXUNIT (F)*
ALENBST (F)*
ALPRIOR
ASSOCDSP
BOXCLR
CNFMU
CNFPU

CONTCUT (F)*
EIPPCODE (F)*
EUDESC
HIGHAL (F)*
KEYWORD
NAME
NODENUM

NODETYP
NTWKNUM
OFFNRMPR (F)*
PNTFORM
PNTNODTY
PNTTYPE
PRIMMOD (F)*

PTDESC
PV
PVFL
S0BOXCLR
S1BOXCLR
SLOTNUM
STATE0

STATE1
STATETXT
UNIT

2.6 BOX NUMERIC


The parameters of the Box Numeric Data Point are listed below in alphabetical order. The Point
Form parameter is set to Full.
ASSOCDSP
CNFMU
CNFPU
EUDESC

KEYWORD
NAME
NODENUM
NODETYP

NTWKNUM
PNTFORM
PNTNODTY
PNTTYPE

PRIMMOD
PTDESC
PV
PVFORMAT

SLOTNUM
UNIT

2.7 BOX TIMER


The parameters of the Box Timer Data Point are listed below in alphabetical order. The Point
Form parameter is set to Full.
ASSOCDSP
COMMAND
EUDESC
KEYWORD
NAME

R610
11/99

NODENUM
NODETYP
NTWKNUM
PERIOD
PNTNODTY

PNTTYPE
PRIMMOD
PTDESC
PV
RV

SLOTNUM
SO
SP
STATE
TIMEBASE

HPM Parameter Reference Dictionary


Honeywell Inc.

UNIT

29

2 PARAMETERS PER POINT TYPE

2.8 DEVICE CONTROL (DEVCTL)


The parameters of the Device Control Data Point are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ACCELTIM
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
BADPVTXT
BADSVFL
BADSVPR (F)
BOXCLR
BYPASS
CMDDISFL
CMDDISPR (F)
CMDFALFL
CMDFALTM
CNFERRFL
CNFMU
CNFPU
CONTCUT
D1
D1_0
D1_1
D2
D2D1_00
D2D1_01
D2D1_10
D2D1_11
D3
D4
D5
DB_VALID
DEADBAND
DEADTIME
DISRC
DODSTN
EIPPCODE (F)
EUDESC
EVTOPT (F)
FBTIME (F)
FL 1-12
HIGHAL (F)
HIGHALPR
HISVPEAK
I0
I0CONF
I1
I1CONF
I2
I2CONF
INITMAN
INITREQ
KEYWORD
L
LIBADOPT
LIDESC
LISRC 1-12
LMREV
LMSRC

30

(#Inputs>0)

(#Inputs>0)

(#Inputs>0)
(#Inputs=1)
(#Inputs=1)
(#Inputs=2)
(#Inputs=2)
(#Inputs=2)
(#Inputs=2)
(#Inputs=2)

(#Inputs>0)
(#Outputs>0)
(#Inputs>0)

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)

LOCALMAN
LODSTN 1-2
LOENBL 1-2
LOGICSRC
LOSRC 1-2
MAINDAT
MAINTOPT
MANMODFL
MASKTIM
MAXTIM0H
MAXTIM1H
MAXTIM2H
MAXTRAN0
MAXTRAN1
MAXTRAN2
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
MOMSTATE
MOVPVFL
MOVPVTXT
NAME
NI0
NI1
NI2
NMODATTR
NMODE
NN
NNINSET 1-10
NODENUM
NODETYP
NODINPTS
NODOPTS
NOLINPTS
NOLOPTS
NONECONF
NONE_OP1-3
NOPGATE
NORMCYCL
NOSGATE
NOSIOVRD
NOSTATES
NOTRANS0
NOTRANS1
NOTRANS2
NRMATRFL
NSI0
NTWKNUM
OFFNRMFL
OFFNRMPR (F)
OP
OPCMD
OPFINAL
OPRATRFL
OROPT

(#Outputs>0)

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Inputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)

(#Outputs>0)

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)

OVRCTIM
OVRDCONF
OVRDDESC
OVRDI0FL
OVRD1FL
OVRD2FL
OVRDALOP
OVRDALPR (F)
OVRDSIFL
P0
P1
P2
PAUSETIM
PERIOD
PFDLYFL
PGALGID 1-4
PGDSTN 1-4
PGPLSWTH 1-4
PGSO 1-4
PIALGID 1-12
PIDEADBD1-12
PINN 1-12
PISO 1-12
PISRC 1-12
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PULSEWTH
PV
PVAUTO
PVFL
PVNORMAL (F)
PVNORMFL
PVSOURCE (F)
PVSRCOPT (F)
PVSTATES 0-4
PVTXTOPT
REDTAG (F)
RESETFL
S0BOXCLR
S1BOXCLR
S2BOXCLR
SCHSTS
SEALOPT
SECVAR
SGALGID 1-2
SGDSTN 1-2
SGPLSWTH 1-2
SGSO 1-2

HPM Parameter Reference Dictionary


Honeywell Inc.

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)

(#Outputs>0)
(#Inputs>0)
(#Inputs>0)
(#Inputs>0)
(#Inputs>0)
(#Inputs>0)
(#Inputs>0)
(#Outputs>0)

R610
11/99

2 PARAMETERS PER POINT TYPE

2.8 Device Control (DevCtl) cont


Continuation of the Device Control parameters are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
SI0
SI0ALOPT
SI0ALPR (F)
SI0CONF
SIALGID 1-12
SIDLYTIM 1-12
SIDSTN 1-12
SISO 1-12
SLOTNUM
SO 0-2
SOCMD
ST0_OP1
ST0_OP2
ST0_OP3
ST1_OP1
ST1_OP2
ST1_OP3
ST2_OP1
ST2_OP2
ST2_OP3

R610
11/99

(#Outputs>0)
(#Outputs>=2)
(#Outputs>=3)
(#Outputs>0)
(#Outputs>=2)
(#Outputs>=3)
(#Outputs>0)
(#Outputs>=2)
(#Outputs>=3)

STATE0
STATE1
STATE2
STATTIM0
STATTIM1
STATTIM2
STATETXT0-4
STCHGOPT
STSMSG
SVALDB
SVALDBEU
SVDESC
SVEUDESC
SVEUHI
SVEULO
SVHHFL

SVHHPR (F)
SVHHTP
SVHHTPP
SVHIFL
SVHIPR (F)
SVHITP
SVHITPP
SVP
SVPEAK
SVSRC
SVTV
SVTVP
TRANTIM0
TRANTIM1
TRANTIM2
UNCMDFL
UNIT
USERID

HPM Parameter Reference Dictionary


Honeywell Inc.

31

2 PARAMETERS PER POINT TYPE

2.9 DIGITAL COMPOSITE (DIGCOMP)


The parameters of the Digital Composite Data Point are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ALPRIOR
ASSOCDSP
BADCTLPR
BADPVFL (F)
BADPVPR (F)
BADPVTXT
BOXCLR
BYPASS
CMDDISFL

MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
MOMSTATE
MOVPVFL
MOVPVTXT
NAME
NI0
NI1

(#Outputs>0)
(#Outputs>0)

CMDDISPR

NI2

(#Outputs>0)

CMDFALFL
CMDFALTM
CNFERRFL
CNFMU
CNFPU
CONTCUT (F)
D1
D1_0
D1_1
D2
D2D1_00
D2D1_01
D2D1_10
D2D1_11
DISRC 1-2
DODSTN 1-3
EIPPCODE (F)
EUDESC
EVTOPT (F)

NMODATTR
NMODE
NODENUM
NODETYP
NODINPTS
NODOPTS
NONECONF
NONE_OP1-3
NORMCYCL
NOSIOVRD
NOSTATES
NOTRANS1
NOTRANS0
NOTRANS2
NRMATRFL
NSI0
NTWKNUM
OFFNRMFL
OFFNRMPR
(F)
OP
OPCMD
OPFINAL
OPRATRFL
OVRDALOP
OPSTTEXT
OVRDALPR
(F)
OROPT
OVRDCONF
OVRDDESC
OVRDI0FL
OVRDI1FL
OVRDI2FL
OVRDSIFL
P0
P1
P2
PAUSETIM
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE

(#Outputs>0)
(#Outputs>0)

FBTIME (F)
HIGHAL (F)
HIGHALPR
I0
I0CONF
I0DESC
I1
I1CONF
I1DESC
I2
I2CONF
I2DESC
INITMAN
INITREQ
KEYWORD
LOCALMAN
LOGICSRC
MAINDAT
MAINTOPT
MAXTIM0H
MAXTIM1H
MAXTIM2H
MAXTRAN0
MAXTRAN1
MAXTRAN2

32

(#Inputs>0)

(#Inputs>0)

(#Inputs>0)
(#Inputs=1)
(#Inputs=1)
(#Inputs=2)
(#Inputs=2)
(#Inputs=2)
(#Inputs=2)
(#Inputs=2)
(#Inputs>0)
(#Outputs>0)

(#Inputs>0)
(#Outputs>0)
(#Outputs>0)

(#Outputs>0)

(#Outputs>0)

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Inputs>0)

(#Outputs>0)

PRIMMOD (F)
PRGATRFL
PSDLYFL
PTDESC
PTEXECST
PTINAL
PULSEWDTH
PV
PVAUTO
PVFL 0-2
PVNORMAL
(F)
PVSOURCE
(F)
PVSRCOPT (F)
PVSTATES 0-4
PVTXTOPT
REDTAG (F)
RESETFL
S0BOXCLR
S1BOXCLR
S2BOXCLR
SCHSTS
SEALOPT
SI0
SI0ALOPT
SI0ALPR (F)
SI0CONF
SLOTNUM
SO
SOCMD
ST0_OP1
ST0_OP2

(#Outputs>0)
(#Inputs>0)
(#Inputs>0)
(#Inputs>0)

(#Inputs>0)
(#Inputs>0)
(#Inputs>0)
(#Outputs>0)

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)
(#Outputs>0)

ST0_OP3
ST1_OP1
ST2_OP1
ST1_OP2
ST2_OP2
ST1_OP3
ST2_OP3

(#Outputs>=2)
(#Outputs>=3)
(#Outputs>0)
(#Outputs>0)
(#Outputs>=2)
(#Outputs>=2)
(#Outputs>=3)

(#Outputs>0)

STATE0
STATE1
STATE2
STATETXT 0-4
STATTIM0
STATTIM1
STATTIM2
STCHGOPT
STSMSG
TRANTIM1
TRANTIM2
UNCMDFL
UNIT
USERID

(#Outputs>=3)

(#Outputs>0)
(#Outputs>0)
(#Outputs>0)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

2 PARAMETERS PER POINT TYPE

2.10 DIGITAL INPUT (DIGIN)


The parameters of the Digital Input Data point are listed below in alphabetical order. (L), (S), or
(R-O)parameter applies only when DITYPE = Latched, Status, or Accum. (F) indicates that
the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (S) (F)
ALMOPT (S) (F)
ALPRIOR
ASSOCDSP
AV (R-O)
AVTV (R-O)
AVTVFL (R-O)
BADPVFL (F)
BADPVPR
BOXCLR (L)
COMMAND (R-O)
CONTCUT (S) (F)
COUNTDWN (R-O)
DEBOUNCE (S) (L)
DITYPE (F)

DLYTIME (S) (F)


EIPPCODE (S) (L) (F)
EUDESC
EVTOPT (L) (F)
HIGHAL (S)
INPTDIR (F)
KEYWORD
MODNUM
NAME
NODENUM
NODETYP
NTWKNUM
OFFNRMFL (S)
OFFNRMPR (S) (F)
OLDAV (R-O)
OVERFLOW (R-O)

OVERVAL (R-O) (F)


PNTFORM
PNTNODTY
PNTMODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PTDESC
PTEXECST
PV (S) (L)
PVAUTO (S) (L)
PVCHGDLY (S) (L) (F)
PVFL (S) (L)
PVNORMAL (S) (F)
PVNORMFL (S)
PVRAW

PVSOURCE (L) (F)


PVSRCOPT (S) (L) (F)
RESETFL (R-O)
RESETVAL (R-O)
S0BOXCLR (S) (L)
S1BOXCLR (S) (L)
SLOTNUM
STARTFL (R-O)
STATE (R-O)
STATE0 (S) (L)
STATE1 (S) (L)
STATETXT 0-2 (S) (L)
STOPFL (R-O)
UNIT

2.11 DIGITAL OUTPUT (DIGOUT)


The parameters of the Digital Output Data point are listed below in alphabetical order. (S) or (P)
parameter applies only when DOTYPE = Status or Pulse Width Modulated (PWM). This point
type is available only in the component form.
ASSOCDSP
DOTYPE
EUDESC
INITREQ
KEYWORD
MODNUM

R610
11/99

NAME
NODENUM
NODETYP
NTWKNUM
OFFPULSE (S)
ONPULSE (S)

OP (P)
OPTDIR (P)
PERIOD (P)
PNTFORM
PNTMODTY
PNTNODTY

PNTSTATE
PNTTYPE
PTDESC
PTEXECST
S0BOXCLR (S)
S1BOXCLR (S)

HPM Parameter Reference Dictionary


Honeywell Inc.

SLOTNUM
SO (S)
STATE0 (S)
STATE1 (S)
STDBYMAN
UNIT

33

2 PARAMETERS PER POINT TYPE

2.12 FBCM (FUNCTION & TRANSDUCER BLOCK CONTROL MODULE)


The FBCM parameters are listed below in alphabetical order.
$AUXUNIT
$OPTOL
$SPTOL
ALENBST
ALMINFO
ALPRIOR
APPL
ASSOCCM
ASSOCDSP
BADPVFL
BADPVPR
BLKDDID
BLKODIDX
CASIN
CASIND
CONTCUT
CVEUHI
CVEULO
DEADBAND
DEVHIFL
DEVHIPR
DEVLOFL
DEVLOPR
DISPTYPE
EUDESC
FBTYPE
FFALMCUR
FFBCINST
FFBCINVL
FFBCOPST
FFBCOPVL
FFCSIDST
FFCSIDVL
FFCSINST
FFCSINVL
FFDVHILM
FFDVHIPR
FFDVLOLM
FFDVLOPR
FFFFDECP
FFFFGAIN
FFFFS0

34

FFFFS100
FFFFUIDX
FFFFVLST
FFFFVLVL
FFGAIN
FFHHLM
FFHHPR
FFHILM
FFHIPR
FFINSTS
FFINVAL
FFLLLM
FFLLPR
FFLOLM
FFLOPR
FFMODEA
FFMODEN
FFMODEP
FFMODET
FFOEXPST
FFOEXPVL
FFOPDECP
FFOPHILM
FFOPLOLM
FFOPS0
FFOPS100
FFOPUIDX
FFOREMST
FFOREMVL
FFOUT1ST
FFOUT1VL
FFOUT2ST
FFOUT2VL
FFOUTAST
FFOUTAVL
FFOUTDST
FFOUTDVL
FFOUTSTS
FFOUTVAL
FFPTRPST
FFPTRPVL
FFPVDECP

FFPVS0
FFPVS100
FFPVSTS
FFPVUIDX
FFPVVAL
FFRATE
FFRBDST
FFRBDVL
FFRBST
FFRBVL
FFRCIDST
FFRCIDVL
FFRCINST
FFRCINVL
FFRCOPST
FFRCOPVL
FFRESET
FFROINST
FFROINVL
FFROOPST
FFROOPVL
FFSEL1ST
FFSEL1VL
FFSEL2ST
FFSEL2VL
FFSEL3ST
FFSEL3VL
FFSPHILM
FFSPLOLM
FFSPRTDN
FFSPRTUP
FFSPSTS
FFSPVAL
FFSTREV
FFTRDIST
FFTRDIVL
FFTRIPST
FFTRIPVL
FFTRVLST
FFTRVLVL
FFXDDECP
FFXDS0

FFXDS100
FFXDUIDX
FL
HIGHAL
HIGHALPR
IN
IND
INITREQ
INT
KEYWORD
LASTPV
MODATTR
MODEAPPL
MODEBLKC
MODEPERM
MODNUM
NAME
NN
NODENUM
NODETYP
NTWKNUM
OFFNRMFL
OFFNRMPR
OP
OUT
OUTD
OUTDST
OUTST
PNTMODTY
PNTNODTY
PNTSTATE
PRIMMOD
PTDESC
PTEXECST
PTINAL
PV
PVAUTO
PVAUTOST
PVCALC
PVCLAMP
PVEUHI
PVEULO

HPM Parameter Reference Dictionary


Honeywell Inc.

PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFL
PVFORMAT
PVHHFL
PVHHPR
PVHIFL
PVHIPR
PVLLFL
PVLLPR
PVLOFL
PVLOPR
PVP
PVRAW
PVSOURCE
PVSRCOPT
PVSTS
PVTV
PVTVP
RCASIN
RCASIND
REDTAG
ROUTIN
SEL1
SEL2
SEL3
SLOTNUM
SO
SP
SPP
STATETXT
STR
TBODIDX
TBTYPE
UNIT
VWODIDX
XBLKDDID
XVWODIDX

R610
11/99

2 PARAMETERS PER POINT TYPE

2.13 IOP
The parameters of the Input/Output Processor Point are listed below in alphabetical order.
CALIBALL
CALIBRJ
FAILOPT
FTAPRES
FREQ6050

IOMACTYP
IOMFWREV
IOMHWREV
IOMLHFST
IOMOPER

IOMTYPE
IOMSTS
IONTOKEN
IOPSTR1
IOPSTR2

IORECCHN
LINEPERD
MAXSLOTS
NODETYP
PIUOTDCF

RJRAW
SLOT0SF
STDBYSTS
SWTCHACT
WARMSTRT

Some of the parameters in the above listing are arrays and are not defined in this publication.

2.14 LOGIC
The parameters of the Logic Data Point (otherwise referred to as the Logic Slot) are listed below
in alphabetical order. (F) indicates that the parameter is applicable when the
PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
C1DESC
C2DESC
C3DESC
C4DESC
C1FL
C2FL
C3FL
C4FL
C1PR (F)
C2PR (F)
C3PR (F)
C4PR (F)
C1SRC

R610
11/99

C2SRC
C3SRC
C4SRC
CNFERRFL
CNFMU
CNFPU
CONTCUT
DEADBAND 1-24
DLYTIME 1-24
EIPPCODE (F)
FL1-12
GENDESC (F) 1-12
HIGHAL
HIGHALPR
L1-12
LIBADOPT

LISRC 1-12
LODSTN 1-12
LOENBL 1-12
LOGALGID 1-24
LOGMIX
LOSRC 1-12
MODNUM
NAME
NN1-8
NODENUM
NODESC (F)
NODETYP
NOLINPTS
NOLOGBLK
NOLOPTS

NORMCYCL
NTWKNUM
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PRIMMOD (F)
PRMDESC 1-12 (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
R1 1-24

HPM Parameter Reference Dictionary


Honeywell Inc.

R2 1-24
S1 1-24
S1REV 1-24
S2 1-24
S2REV 1-24
S3 1-24
S3REV 1-24
S4 1-24
SCHSTS
SLOTNUM
SO 1-24
STSMSG
UNIT
USERID

35

2 PARAMETERS PER POINT TYPE

2.15 PECM (PHYSICAL ENTITY CONTROL MODULE)


The PECM parameters are listed below in alphabetical order.
ASSOCCM
ASSOCDSP
BLKDDID
BLKODIDX
DEVSTAT
DISPTYPE
EUDESC
FFDEVREV

FFMODEA
FFMODEN
FFMODEP
FFMODET
FFSTREV
FL
INT
KEYWORD

MODEBLKC
MODNAME
MODNUM
NAME
NN
NODENUM
NODETYP
NTWKNUM

PNTMODTY
PNTNODTY
PNTSTATE
PRIMMOD
PTDESC
PTEXECST
RSSTATE
SLOTNUM

STR
UNIT
USEVFDNO
VENNAME
VFDREF
VFDTAG
VWODIDX

2.16 PROCESS MODULE (PROCMOD)


The parameters of the Process Module Data Point are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
ABHEMSD
ABHHOLD
ABHRSTR
ABHSHDN
ACP (F)
ALPRIOR (F)
ANAME 1-3
ASSOCDSP
ASTEP 1-3
ASTMT 1-3
AVGPU
BADIOLPF
CNFMU
CNFPU
CNTLLOCK
CLBACK

36

DIAGCMD
FL 1-27
IOLPSERR
IOLPSOPT
LSTWHNER
MAXPU
MSGPEND
NAME (F)
NN 1-80
NODENUM
NODETYP
NOOVRRUN
NTWKNUM
OVERPHAS
OVERSTAT

OVERSTEP
OVRRUNFL
OVRRUNPR
PERIOD
PFDLYFL
PHASE
PHASEAL
PHASETIM
PHREMTIM
PNTFORM
PNTNODTY
PNTTYPE
PROCMOD
PRIMMOD (F)
PSDLYFL

PTDESC
RESTART
RSTROPT
RUNSTATE
SEQERR
SEQEXEC
SEQMODE
SEQNAME
SEQOBJSZ
SEQPR (F)
SEQSLTSZ
SLOTNUM
SNAME 1-2
SPLOCK
SSTEP 1-2

HPM Parameter Reference Dictionary


Honeywell Inc.

SSTMT 1-2
STATMENT
STEP
STR8 1-16
STR16 1-8
STR32 1-4
STR64 1-2
STRLEN
STSMSG
SUSPSTAT
SUSPTIME
TIME 1-4
UNIT
USERID

R610
11/99

2 PARAMETERS PER POINT TYPE

2.17 SECM (SEGMENT ENTITY CONTROL MODULE)


The SECM parameters are listed below in alphabetical order.
Listed
ACTSCHVR
ACTVSCHD
ASSOCDSP
DISPTYPE
EUDESC
FFDEVREV

KEYWORD
MODNAME
MODNUM
NAME
NODENUM
NODETYP

NTWKNUM
NUMSCHD
PNTMODTY
PNTNODTY
PNTSTATE
PRILNKMS

PRIMMOD
PTDESC
PTEXECST
SCHDVER
SLOTNUM
UNIT

VENNAME
VFDREF
VFDTAG

2.18 UCN NETWORK


Listed below in alphabetical order are the parameters of the UCN Network Data Point (system
parameter $NTWRKnn where nn = the UCN number).
CHPINHWY
CLPZMXC
CLPZMXP

HWYCTLST
LOADSCOP
MSGTXT 0-15

NIMADDR
NIMREV
NIMVERS

NMSGTXT
TIMESYNC
UPGRADE

2.19 UCN NODE


The parameters of the UCN Node Data Point are listed below in alphabetical order. They can be
accessed as follows:
$NMuuNnn.parameter where,
uu is the UCN network number, and nn is the UCN node number.
$UCNLSB 1-50
CABLESTS
CLPZMXC
CLPZMXP
LOADSCOP
MDMHWREV
MODNUM
NMSGTXT

NODESTS
NODESTAT
NODETYP
NPRQUAVG*
NPRQUMAX*
NPRSPAVG*
NPRSPMAX*

NTRQUAVG*
NTRQUMAX*
NTRSPAVG*
NTRSPMAX*
TIMESYNC
TRATAVG
TRATMAX

UCNRECHN
UPGRADE
UTSDRIFT
UTSNODE
UTSTBCRV
UTSTIME
UTSTIMST

*These parameters are indexed. The index is either an odd number from 1 to 63 and represents either
the UCN node number of a peer node for peer-to-peer statistics with that node
0 for the sum of all peer-to-peer statistics
Example for case 2 is: NPRQUAVG(0) = NPRQUAVG(1) + NPRQUAVG(3) + ... + NPRQUAVG(63)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

37

2 PARAMETERS PER POINT TYPE

38

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE


This section contains listings of parameters that are applicable to each PV and control algorithm in the
HPM. Refer to Sections $ - X for the definitions of the parameters.

3.1 AUTO MANUAL (AUTOMAN)


The parameters of the Auto Manual control algorithm are listed below in alphabetical
order. (F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ARWNET
ARWOP
ASSOCDSP
AUTMODFL
B
BO
BADCTLFL
BADCTLOP
BADCTLPR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLEQN
CTLALGID

CTRLINIT
CV
CVEUHI
CVEULO
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
K
KEYWORD
LOCALMAN
MANMODFL
MODATTR
MODEAPPL
MODE
MODEPERM
MODNUM

NAME
NMODATTR
NMODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM

OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PTORST
RARWSTS

RATE1
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
SAFEOP
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
STDBYMAN
STSMSG
UNIT
USERID
X1
X2
XEUHI
XEULO

3.2 CALCULATOR (CALCULTR)


The parameters of the Calculator PV algorithm are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
C1
C2
C3
C4
CALCEXP
CNFMU
CNFPU
CONTCUT (F)
EUDESC
HIGHAL (F)
HIGHALPR (F)
KEYWORD
LASTPV
MODNUM
N

R610
11/99

NAME
P3
NODENUM
NODETYP
NOPINPTS
NORMCYCL
NTWKNUM
OVERVAL (F)
P1
P1STS
P2
P2STS
P3STS
P4
P4STS
P5
P5STS
P6
P6STS
PERIOD

PFDLYFL
PIDSTN
PISRC
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC

PVCLAMP
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)

HPM Parameter Reference Dictionary


Honeywell Inc.

PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
PVTV (F)
PVTVP (F)
SCHSTS
SLOTNUM
STSMSG
TF
UNIT
USERID

39

3 PARAMETERS PER ALGORITHM TYPE

3.3 DATA ACQUISITION (DATAACQ)


The parameters of the Data Acquisition PV algorithm are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
CONCUT (F)
CNFMU
CNFPU
EUDESC
HIGHAL (F)
HIGHALPR (F)
KEYWORD
LASTPV
MODNUM
NAME
NODENUM
NODETYP

NOPINPTS
NORMCYCL
NTWKNUM
OVERVAL (F)
P1
P1STS
PERIOD
PFDLYFL
PIDSTN
PISRC
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL

PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC
PVCLAMP
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL

PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)

PVROCNTP (F)
PVROCPVFL
PVROCPPR (F)
PVROVPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
PVTV (F)
PVTVP (F)
SCHSTS
SLOTNUM
STSMSG
TF
UNIT
USERID

3.4 FLOW COMPENSATION (FLOWCOMP)


The parameters of the Flow Compensation PV algorithm are listed below in alphabetical order.
(F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
C
C1
C2
CNFMU
CNFPU
COMPHILM
COMPLOLM
COMPTERM
CONTCUT (F)
EUDESC
F
FSTS
G
GSTS
HIGHAL (F)
HIGHALPR (F)
KEYWORD

40

LASTPV
MODNUM
NAME
NODENUM
NODETYP
NOPINPTS
NORMCYCL
NTWKNUM
OVERVAL (F)
P
PERIOD
PFDLYFL
P0
PIDSTN
PISRC
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSTS

PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC
PVCHAR
PVCLAMP
PVEQN
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL

PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)

HPM Parameter Reference Dictionary


Honeywell Inc.

PVSTS
PVTV (F)
PVTVP (F)
Q
QSTS
RG
RP
RQ
RT
RX
SCHSTS
SLOTNUM
STSMSG
T
T0
TF
TSTS
UNIT
USERID
X
XSTS

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE

3.5 GENERAL LINEARIZATION (GENLIN)


The parameters of the General Linearization PV algorithm are listed below in alphabetical order.
(F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADVPR (F)
CNFMU
CNFPU
CONTCUT (F)
EUDESC
HIGHAL (F)
HIGHALPR (F)
IN0
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
IN9
IN10
IN11

IN12
KEYWORD
LASTPV
MODNUM
NAME
NODENUM
NODETYP
NOPINPTS
NORMCYCL
NTWKNUM
OUT0
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
OUT8
OUT9
OUT10
OUT11
OUT12

OVERVAL (F)
P1
P1STS
PERIOD
PFDLYFL
PIDSTN
PISRC
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVAUTO
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTOST

PVCALC
PVCLAMP
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP

PVROCNFL
PVROCNPR
PVROCNTP
PVROCPFL
PVROCPPR
PVROCPTP
PVSGCHTP
PVSOURCE
PVSRCOPT
PVSTS
PVTV (F)
PVTVP (F)
SCHSTS
SEGTOT
SLOTNUM
STSMSG
TF
UNIT
USERID

(F)
(F)
(F)
(F)
(F)
(F)
(F)

3.6 HIGH-LOW AVERAGE (HILOAVG)


The parameters of the High-Low Average PV algorithm are listed below in alphabetical order.
(F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
CNFMU
CNFPU
CONTCUT (F)
EUDESC
FORCE
FRCPERM
FSELIN
HIGHAL (F)
HIGHALPR (F)
KEYWORD
LASTPV
MODNUM
N
NAME
NMIN
NODENUM

R610
11/99

NODETYP
NOPINPTS
NORMCYCL
NTWKNUM
OVERVAL (F)
P1
P1STS
P2
P2STS
P3
P3STS
P4
P4STS
P5
P5STS
P6
P6STS
PERIOD
PFDLYFL
PIDSTN

PISRC
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC
PVCLAMP
PVEQN

PVEUHI
PVEULO
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)

HPM Parameter Reference Dictionary


Honeywell Inc.

PVP
PVROCNFL
PVROCNPR
PVROCNTP
PVROCPFL
PVROCPPR
PVROCPTP
PVSGCHTP
PVSOURCE
PVSRCOPT
PVSTS
PVTV (F)
PVTVP (F)
SCHSTS
SELINP
SLOTNUM
STSMSG
TF
UNIT
USERID

(F)
(F)
(F)
(F)
(F)
(F)
(F)

41

3 PARAMETERS PER ALGORITHM TYPE

3.7 INCREMENTAL SUMMER (INCRSUM)


The parameters of the Incremental Summer control algorithm are listed below in alphabetical
order. (F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ARWNET
ARWOP
ASSOCDSP
AUTMODFL
BADCTLFL
BADCTLPR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLALGID
CTRLINIT
CV
CVEUHI
CVEULO

DELCV
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
K1
K2
K3
K4
KEYWORD
LOCALMAN
M
MANMODFL
MODATTR
MODE
MODEAPPL
MODEPERM

MODNUM
NAME
NMODATTR
NMODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL

OPLOLM
OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PTORST

RARWSTS
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
SAFEOP
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
STDBYMAN
STSMSG
UNIT
USERID
X1
X2
X3
X4
XEUHI
XEULO

3.8 MIDDLE-OF-3 (MIDOF3)


The parameters of the Middle-Of-3 PV algorithm are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
CNFMU
CNFPU
CONTCUT (F)
EUDES C
HIGHAL (F)
HIGHALPR (F)
KEYWORD
LASTPV
MODNUM
NAME
NODENUM
NODETYP
NOPINPTS

42

NORMCYCL
NTWKNUM
OVERVAL (F)
P1
P1STS
P2
P2STS
P3
P3STS
PERIOD
PFDLYFL
PIDSTN
PISRC
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE

PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC
PVCLAMP
PVEQN
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO

PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL

HPM Parameter Reference Dictionary


Honeywell Inc.

PVROCNPR
PVROCNTP
PVROCPFL
PVROCPPR
PVROCPTP
PVSGCHTP
PVSOURCE
PVSRCOPT
PVSTS
PVTV (F)
PVTVP (F)
SCHSTS
SELINP
SLOTNUM
STSMSG
TF
UNIT
USERID

(F)
(F)
(F)
(F)
(F)
(F)
(F)

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE

3.9 MULTIPLY/DIVIDE (MULDIV)


The parameters of the Multiply/Divide control algorithm are listed below in alphabetical order.
(F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ARWNET
ARWOP
ASSOCDSP
AUTMODFL
B
B1, B2, B3
BADCTLFL
BADCTLOP
BADCTLPR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLALGID

CTLEQN
CTRLINIT
CV
CVEUHI
CVEULO
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
K
K1, K2, K3
KEYWORD
LOCALMAN
MANMODFL
MODATTR
MODE

MODEAPPL
MODEPERM
MODNUM
NAME
NMODATTR
NMODE
NOCINPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)

OPLAFL (F)
OPLOFL
OPLOLM
OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD (F)
PSDLYFL
PTDESC

PTEXECST
PTINAL
PTORST
RARWSTS
RATE1
RCASOPT
REDTAG (F)
RINITREQ
RINITVAL
SAFEOP
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
STDBYMAN
STSMSG
UNIT
USERID
X1, X2, X3

3.10 OVERRIDE SELECTOR (ORSEL)


The parameters of the Override Selector control algorithm are listed below in alphabetical order.
(F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ARWNET
ARWOP
ASSOCDSP
AUTMODFL
BADCTLFL
BADCTLOP
BADCTLPR (F)
BCAMODFL
BYPASS
BYPASSX1
BYPASSX2
BYPASSX3
BYPASSX4
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN

R610
11/99

CONTCUT (F)
CTALGID
CTLEQN
CTRLINIT
CV
CVEUHI
CVEULO
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
KEYWORD
LOCALMAN
M
MANMODFL
MODE
MODEAPPL
MODEPERM

MODNUM
NAME
NMODATTR
MODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM

OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OROFFSET
OROPT
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PTORST

HPM Parameter Reference Dictionary


Honeywell Inc.

RARWSTS
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
SAFEOP
SCHSTS
SELXINP
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
STDBYMAN
STSMSG
UNIT
USERID
X1
X2
X3
X4
XEUHI
XEULO

43

3 PARAMETERS PER ALGORITHM TYPE

3.11 PID
The parameters of the PID control algorithm are listed below in alphabetical order. (F) indicates
that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ADVDEVFL
ADVDEVPR (F)
ADVDEVTP (F)
ADVSP (F)
ADVSPP (F)
ALENBST (F)
ARWNET
ARWOP
ASPPROC (F)
ASSOCDSP
AUTMODFL
BADCTLFL
BADCTLOP
BADCTLPR (F)
BADPVFL (F)
BADPVPR (F)
BCAMODFL
BIAS
BSHILM
BSLOLM
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLACTN
CTLALGID
CTLEQN
CTRLINIT
CV
CVEUHI
CVEULO
DELCV
DEV
DEVHIFL

44

DEVHITP (F)
DEVLOFL
DEVLOPR (F)
DEVLOTP (F)
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
GAINOPT
GAPHI
GAPLO
HIGHAL (F)
HIGHALPR (F)
INITMAN
K
KEXT
KEYWORD
KGAP
KLIN
KNL
LASTPV
LMSRC
LOCALMAN
MANMODFL
MANOPCMD
MANOPTIME
MAXPULSE
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
NAME
NLFM
NLGAIN
NMODATTR
NMODE

NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPCMD
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHISRC
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM
OPLOPR (F)
OPLOSRC
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PIDFORM
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PSDLYFL

PTDESC
PTEXECST
PTINAL
PTORST
PV
PVALDB (F)
PVALDBEU (F)
PVAUTO
PVAUTOST
PVEUHI
PVEULO
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITPID
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOTP (F)
PVLOPR (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
PVTRACK
RAMPTIME
RARWSTS
RATIO

HPM Parameter Reference Dictionary


Honeywell Inc.

RBOPT
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
RTHILM
RTLOLM
SAFEOP
SAFOPCMD
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
SP
SPEUHI
SPEULO
SPFORMAT
SPHIFL
SPHILM
SPLOFL
SPLOLM
SPOPT
SPP
$SPTOL
SPTV
SPTVP
STDBYMAN
STSMSG
T1
T2
TVPROC
UNIT
USERID

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE

3.12 PID WITH EXTERNAL RESET FEEDBACK (PIDERFB)


The parameters of the PID with External Reset Feedback control algorithm are listed below in
alphabetical order. (F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ADVDEVFL
ADVDEVPR (F)
ADVDEVTP (F)
ADVSP (F)
ADVSPP (F)
ALENBST (F)
ARWNET
ARWOP
ASSOCDSP
ASPPROC (F)
AUTMODFL
BADCTFL
BADCTLOP
BADCTLPR (F)
BADPVFL (F)
BADPVPR (F)
BCAMODFL
BIAS
BSHILM
BSLOLM
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLACTN
CTLALGID
CTLEQN
CTRLINIT
CV
CVEUHI
CVEULO
DELCV
DEV

R610
11/99

DEVHIFL
DEVHIPR (F)
DEVHITP (F)
DEVLOFL
DEVLOPR (F)
DEVLOTP (F)
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
GAINOPT
GAPHI
GAPLO
HIGHAL (F)
HIGHALPR (F)
INITMAN
K
K1
KEXT
KEYWORD
KGAP
KLIN
KNL
LASTPV
LOCALMAN
MANMODFL
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
NAME
NLFM
NLGAIN
NMODATTR
NMODE

NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM
OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PIDFORM
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PSDLYFL
PTDESC
PTEXECST

PTINAL
PTORST
PV
PVALDB (F)
PVALDBEU (F)
PVAUTO
PVAUTOST
PVEUHI
PVEULO
PVFORMAT
PVHHFL
PVHHTP (F)
PVHHPR (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOTP (F)
PVLOPR (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
PVTRACK
RAMPTIME
RARWSTS
RATIO
RBOPT

HPM Parameter Reference Dictionary


Honeywell Inc.

RCASOPT
RCASSHED
REDTAG (F)
RFB
RINITREQ
RINITVAL
RTHILM
RTLOLM
S1
SAFEOP
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
SP
SPEUHI
SPEULO
SPFORMAT
SPHIFL
SPHILM
SPLOFL
SPLOLM
SPOPT
SPP
$SPTOL
SPTV
SPTVP
STSMSG
STDBYMAN
T1
T2
TRFB
TVPROC
UNIT
USERID

45

3 PARAMETERS PER ALGORITHM TYPE

3.13 PID WITH FEED FORWARD (PIDFF)


The parameters of the PID with Feed Forward control algorithm are listed below in alphabetical
order. (F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ADVDEVFL
ADVDEVPR (F)
ADVDEVTP
ADVSP (F)
ADVSPP (F)
ALENBST (F)
ARWNET
ARWOP
ASPPROC (F)
ASSOCDSP
AUTMODFL
BADCTLFL
BADCTLOP
BADCTLPR (F)
BADPVFL (F)
BADPVPR (F)
BCAMODFL
BFF
BIAS
BSHILM
BSLOLM
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLACTN
CTLALGID
CTLEQN
CTRLINIT
CV
CVEUHI
CVEULO
DELCV

46

DEV
DEVHIFL
DEVHIPR (F)
DEVHITP (F)
DEVLOFL
DEVLOPR (F)
DEVLOTP (F)
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
FF
FFOPT
GAINOPT
GAPHI
GAPLO
HIGHAL (F)
HIGHALPR (F)
INITMAN
K
KEXT
KEYWORD
KFF
KGAP
KLIN
KNL
LASTPV
LOCALMAN
MANMODFL
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
NAME
NLFM

NLGAIN
NMODATTR
NMODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM
OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PIDFORM
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL

PSDLYFL
PTDESC
PTEXECST
PTINAL
PTORST
PV
PVALDB (F)
PVALDBEU (F)
PVAUTO
PVAUTOST
PVEUHI
PVEULO
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOTP (F)
PVLOPR (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
PVTRACK
RAMPTIME

HPM Parameter Reference Dictionary


Honeywell Inc.

RARWSTS
RATIO
RBOPT
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
RTHILM
RTLOLM
SAFEOP
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
SP
SPEUHI
SPEULO
SPFORMAT
SPHIFL
SPHILM
SPLOFL
SPLOLM
SPOPT
SPP
SPTV
$SPTOL
SPTVP
STDBYMAN
STSMSG
T1
T2
TVPROC
UNIT
USERID

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE

3.14 PID POSITION PROPORTIONAL (PIDPOSPR)


The parameters of the PID Position Proportional control algorithm are listed below in
alphabetical order.
$AUXUNIT (F)
ADVDEVFL
ADVDEVPR (F)
ADVDEVTP (F)
ADVSP (F)
ADVSPP (F)
ALENBST (F)
ARWNET
ARWOP
ASPPROC (F)
ASSOCDSP
AUTMODFL
BADCTLFL
BADCTLOP
BADCTLPR (F)
BADPVFL (F)
BADPVPR (F)
BADPVR (F)
BCAMODFL
BIAS
BSHILM
BSLOLM
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLACTN
CTLALGID
CTLEQN
CTRLINIT
CYCLETIM
DEADBAND
DEADTIME
DELCV

R610
11/99

DEV
DEVHIFL
DEVHIPR (F)
DEVHITP (F)
DEVLOFL
DEVLOPR (F)
DEVLOTP (F)
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
GAINOPT
GAPHI
GAPLO
HIGHAL (F)
HIGHALPR (F)
INITMAN
K
K1
KEXT
KEYWORD
KGAP
KLIN
KNL
LASTPV
LMSRC
LOCALMAN
LOWERTIM
LOWRDSTN
LOWRRATE
MANMODFL
MANOPCMD
MANOPTIM
MAXPULSE
MINPULSE
MODATTR

MODE
MODEAPPL
MODEPERM
MODNUM
NAME
NLFM
NLGAIN
NMODATTR
NMODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OPCMD
OPHIFL
OPHISRC
OPLOFL
OPLOSRC
OVERVAL (F)
PERIOD
PFDLYFL
PIDFORM
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PTORST

PV
PVALDB (F)
PVALDBEU (F)
PVAUTO
PVAUTOST
PVEUHI
PVEULO
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
PVTRACK
RAISDSTN
RAISETIM
RAISRATE
RAMPTIME
RARWSTS
RATIO

HPM Parameter Reference Dictionary


Honeywell Inc.

RBOPT
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
RP
RT
RTHILM
RTLOLM
SAFEOPCMD
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
SP
SPEUHI
SPEULO
SPFORMAT
SPHIFL
SPHILM
SPLOFL
SPLOLM
SPOPT
SPP
$SPTOL
SPTV
SPTVP
STDBYMAN
STSMSG
T1
T2
TVPROC
UNIT
USERID

47

3 PARAMETERS PER ALGORITHM TYPE

3.15 POSITION PROPORTIONAL (POSPROP)


The parameters of the Position Proportional control algorithm are listed below in alphabetical
order. (F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ADVDEVFL
ADVDEVPR (F)
ADVDEVTP (F)
ADVSP (F)
ADVSPP (F)
ALENBST (F)
ARWNET
ARWOP
ASPPROC (F)
ASSOCDSP
AUTMODFL
BADCTLFL
BADCTLOP
BADCTLPR (F)
BADPVFL (F)
BADPVR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLALGID
CTRLINIT
CYCLETIM
DEADBAND
DEADTIME
DEV
DEVHIFL

48

DEVHIPR (F)
DEVHITP (F)
DEVLOFL
DEVLOPR (F)
DEVLOTP (F)
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
KEYWORD
LASTPV
LMSRC
LOCALMAN
LOWERTIM
LOWRDSTN
LOWRRATE
LTIMHILM
MANMODFL
MANOPCMD
MANOPTIM
MAXPULSE
MINPULSE
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
NAME

NMODATTR
NMODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OPCMD
OPHIFL
OPHISRC
OPLOFL
OPLOSRC
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PSDLYFL
PRIMMOD (F)
PTDESC
PTEXECST
PTINAL
PTORST
PV
PVALDB (F)
PVALDBEU (F)

PVAUTO
PVAUTOST
PVEUHI
PVEULO
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
RAISDSTN
RAISETIM
RAISRATE
RAMPTIME
RARWSTS

HPM Parameter Reference Dictionary


Honeywell Inc.

RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
RP
RT
SAFOPCMD
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
SP
SPEUHI
SPEULO
SPFORMAT
SPHIFL
SPHILM
SPLOFL
SPLOLM
SPOPT
SPP
$SPTOL
SPTV
SPTVP
STDBYMAN
STSMSG
TVPROC
UNIT
USERID

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE

3.16 RAMP SOAK (RAMPSOAK)


The parameters of the Ramp Soak control algorithm are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ADVDEVFL
ADVDEVPR (F)
ADVDEVTP (F)
ADVSP (F)
ADVSPP (F)
ALENBST (F)
ARWNET
ARWOP
ASPPROC (F)
ASSOCDSP
AUTMODFL
BADCTLFL
BADCTLPR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLALGID
CTRLINIT
CURSEGID
CV
CVEUHI
CVEULO
CYCLEOPT
DEV
DEVHIPR (F)
DEVHIFL

R610
11/99

DEVHITP (F)
DEVLOFL
DEVLOPR (F)
DEVLOTP (F)
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
HOLDCMD
INITMAN
KEYWORD
LASTPV
LOCALMAN
MANMODFL
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
MXRMPDEV`
MXSOKDEV
NAME
NMODATTR
NMODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NORSSEQ

NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
NXTSOAKV
OP
OPEU
OPHIFL
OPHILM
OPLOFL
OPLOLM
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD
PSDLYFL
PTDESC
PTEXECST
PTINAL
PTORST
PV
PVEUHI
PVEULO

PVFORMAT
PVP
PVSTS
RAMPTIME
RARWSTS
RATE1
RATE2
RATE3
RATE4
RATE5
RATE6
RATE7
RATE8
RATE9
RATE10
RATE11
RATE12
REDTAG (F)
REMSOAKT
RINITREQ
RINITVAL
S1
S1BGNTIM
S1ENDTIM
S1SEGID
S2
S2BGNTIM
S2ENDTIM
S2SEGID
SAFEOP
SCHSTS
SEGTYPE
SHUTDOWN

HPM Parameter Reference Dictionary


Honeywell Inc.

SLOTNUM
SOAKT1
SOAKT2
SOAKT3
SOAKT4
SOAKT5
SOAKT6
SOAKT7
SOAKT8
SOAKT9
SOAKT10
SOAKT11
SOAKT12
SOAKV1
SOAKV2
SOAKV3
SOAKV4
SOAKV5
SOAKV6
SOAKV7
SOAKV8
SOAKV9
SOAKV10
SOAKV11
SOAKV12
SP
SPP
STDBYMAN
STSMSG
TVPROC
UNIT

49

3 PARAMETERS PER ALGORITHM TYPE

3.17 RATIO CONTROL (RATIOCTL)


The parameters of the Ratio-Control control algorithm are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ADVDEVFL
ADVDEVPR (F)
ADVDEVTP (F)
ADVSP (F)
ADVSPP (F)
ALENBST (F)
ARWNET
ARWOP
ASPPROC (F)
ASSOCDSP
AUTMODFL
B
BO
B1
B2
BADCTLFL
BADCTLPR (F)
BADPVFL (F)
BADPVPR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLALGID
CTRLINIT
CV
CVEUHI
CVEULO

50

DEV
DEVHIFL
DEVHIPR
DEVHITP (F)
DEVLOFL
DEVLOPR (F)
DEVLOTP (F)
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
K1
K2
KEYWORD
LASTPV
LOCALMAN
MANMODFL
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
NAME
NMODATTR
NMODE
NOCINPTS
NOCOPTS
NODENUM
NODETYP

NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM
OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL

PTORST
PRGATRFL
PV
PVALDB (F)
PVALDBEU (F)
PVAUTO
PVAUTOST
PVEUHI
PVEULO
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
RAMPTIME

HPM Parameter Reference Dictionary


Honeywell Inc.

RARWSTS
RATE1
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
SAFEOP
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
SP
SPEUHI
SPEULO
SPFORMAT
SPHIFL
SPHILM
SPLOFL
SPLOLM
SPOPT
SPP
$SPTOL
SPTV
SPTVP
STDBYMAN
STSMSG
TVPROC
UNIT
USERID
X2
X2FILT
X2TF

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE

3.18 SUMMER (REGCTL)


The parameters of the Regulatory Control Summer algorithm are listed below in alphabetical
order. (F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ARWNET
ARWOP
ASSOCDSP
AUTMODFL
B
BADCTLFL
BADCTLOP
BADCTLPR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLALGID
CTLEQN
CTRLINIT

CV
CVEUHI
CVEULO
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
K
K1, K2, K3, K4
KEYWORD
LOCALMAN
M
MANMODFL
MODATTR
MODE
MODEAPPL
MODEPERM

MODNUM
NAME
NMODATTR
NMODE
NOCINPTS
NODENUM
NODETYP
NORMCYCL
NRMATRFL
NRMMODFL
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM

OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL
OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PSDLYFL
PRIMMOD (F)
PTDESC
PTEXECST
PTINAL
PTORST
RARWSTS

RATE1
RCASOPT
REDTAG (F)
RINITREQ
RINITVAL
SAFEOP
SCHSTS
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
STDBYMAN
STSMSG
UNIT
USERID
X1, X2, X3, X4
XEUHI
XEULO

3.19 SUMMER (REGPV)


The parameters of the Summer Regulatory PV algorithm are listed below in alphabetical order.
(F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
C
C1
C2
C3
C4
C5
C6
CNFMU
CNFPU
CONTCUT
D
EUDESC
HIGHAL (F)
HIGHALPR (F)
KEYWORD
LASTPV

R610
11/99

N
MODNUM
NAME
NODENUM
NODETYP
NOPINPTS
NORMCYCL
NTWKNUM
OVERVAL (F)
P1
P1STS
P2
P2STS
P3
P3STS
P4
P4STS
P5
P5STS
P6
P6STS

PERIOD
PFDLYFL
PISRC
PIDSTN
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC

PVCLAMP
PVEQN
PVEULO
PVEUHI
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)

HPM Parameter Reference Dictionary


Honeywell Inc.

PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL
PVROCPPR (F)
PVROCPTP (F)
PVSGCHTP (F)
PVSOURCE (F)
PVSRCOPT (F)
PVSTS
PVTV (F)
PVTVP (F)
SCHSTS
SLOTNUM
STSMSG
TF
UNIT
USERID

51

3 PARAMETERS PER ALGORITHM TYPE

3.20 SWITCH
The parameters of the Switch control algorithm are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ARWNET
ARWOP
ASSOCDSP
AUTMODFL
BADCTFL
BADCTLOP
BADCTLPR (F)
BCAMODFL
CASMODFL
CASREQ
CIDSTN
CISRC
CNFMU
CNFPU
CODSTN
CONTCUT (F)
CTLALGID
CTLEQN
CTRLINIT
CV
CVEUHI

CVEULO
ESWAUTO
ESWCAS
ESWENBST
ESWMAN
EUDESC
EXTSWOPT
HIGHAL (F)
HIGHALPR (F)
INITMAN
KEYWORD
LOCALMAN
M
MANMODFL
MODATTR
MODE
MODEAPPL
MODEPERM
MODNUM
NAME
NMODATTR
NMODE
NRMATRFL

NRMMODFL
NOCINPTS
NOCOPTS
NODENUM
NODETYP
NTWKNUM
OP
OPALDB (F)
OPEU
OPHAFL (F)
OPHIFL
OPHILM
OPHIPR (F)
OPHITP (F)
OPLAFL (F)
OPLOFL
OPLOLM
OPLOPR (F)
OPLOTP (F)
OPMCHLM
OPRATRFL
OPROCLM
$OPTOL

OVERVAL (F)
PERIOD
PFDLYFL
PNTFORM
PNTMODTY
PNTNODTY
PNTSTATE
PNTTYPE
PRGATRFL
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PTORST
RARWSTS
RCASOPT
RCASSHED
REDTAG (F)
RINITREQ
RINITVAL
S1
S2

S3
S4
SAFEOP
SCHSTS
SELXINP
SHEDMODE
SHEDTIME
SHUTDOWN
SLOTNUM
STDBYMAN
STSMSG
TRACKING
UNIT
USERID
X1
X2
X3
X4
XEUHI
XEULO

3.21 TOTALIZER (TOTALIZR)


The parameters of the Totalizer PV algorithm are listed below in alphabetical order. (F)
indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ACCTYPE
ALENBST (F)
ASSOCDSP
AVDEV1FL
AVDEV1TP
AVDEV2FL
AVDEV2TP
AVTV
AVTVFL
BADPVFL (F)
BADPVPR (F)
C
COMMAND
CONTCUT (F)
CNFMU
CNFPU
CUTOFFLM
EUDESC
HIGHAL (F)
HIGHALPR (F)

52

KEYWORD
LASTPV
MODNUM
NAME
NODENUM
NODETYP
NOPINPTS
NORMCYCL
NTWKNUM
OLDAV
OVERVAL (F)
P1
P1STS
P2
P2STS
PERIOD
PFDLYFL
PIDSTN
PISRC
PNTFORM
PNTMODTY

PNTNODTY
PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC
PVCLAMP
PVEQN
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO

PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)
PVROCPFL

HPM Parameter Reference Dictionary


Honeywell Inc.

PVROCPPR
PVROCPTP
PVSGCHTP
PVSOURCE
PVSRCOPT
PVSTS
PVTV (F)
PVTVP (F)
RESETFL
RESETVAL
SCHSTS
SLOTNUM
STARTFL
STATE
STOPFL
STSMSG
TF
TIMEBASE
UNIT
USERID

(F)
(F)
(F)
(F)
(F)

R610
11/99

3 PARAMETERS PER ALGORITHM TYPE

3.22 VARIABLE DEAD TIME WITH LEAD/LAG (VDTLDLAG)


The parameters of the Variable Dead Time with Lead/Lag PV algorithm are listed below in
alphabetical order. (F) indicates that the parameter is applicable when the PNTFORM = Full.
$AUXUNIT (F)
ALENBST (F)
ASSOCDSP
BADPVFL (F)
BADPVPR (F)
C
C1
C2
CNFMU
CNFPU
CONTCUT (F)
CUTOFFLM
D
D1
D2
EUDESC
HIGHAL (F)
HIGHALPR (F)
KEYWORD
LASTPV

R610
11/99

MODNUM
NAME
NLOC
NODENUM
NODETYP
NOPINPTS
NORMCYCL
NTWKNUM
OVERVAL (F)
P1
P1STS
P2
P2STS
PERIOD
PFDLYFL
PIDSTN
PISRC
PNTFORM
PNTMODTY
PNTNODTY

PNTSTATE
PNTTYPE
PRIMMOD (F)
PSDLYFL
PTDESC
PTEXECST
PTINAL
PV
PVALDB (F)
PVALDBEU (F)
PVALGID
PVAUTO
PVAUTOST
PVCALC
PVCLAMP
PVEQN
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO

PVEXHIFL
PVEXLOFL
PVFORMAT
PVHHFL
PVHHPR (F)
PVHHTP (F)
PVHIFL
PVHIPR (F)
PVHITP (F)
PVINIT
PVLLFL
PVLLPR (F)
PVLLTP (F)
PVLOFL
PVLOPR (F)
PVLOTP (F)
PVP
PVROCNFL
PVROCNPR (F)
PVROCNTP (F)

HPM Parameter Reference Dictionary


Honeywell Inc.

PVROCPFL
PVROCPPR
PVROCPTP
PVSGCHTP
PVSOURCE
PVSRCOPT
PVSTS
PVTV (F)
PVTVP (F)
SCHSTS
SLOTNUM
STSMSG
TD
TF
TLD
TLG1
TLG2
UNIT
USERID

(F)
(F)
(F)
(F)
(F)

53

3 PARAMETERS PER ALGORITHM TYPE

54

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

HPM PARAMETER DEFINITIONS ($ THROUGH Y)

This section contains an alphabetical list of the HPM parameters, along with their
descriptors. These parameters start with $ and end with Y.

-$$ADD (Array)
Type:
Lock:
Default:
PtRes:
Range:

Logical
PtBld
On
HPM
Off
On
Helpful Hint:

Add Point Last Parameter IndicatorThe last parameter sent to the HPM
during point build of an array point.

Do not remove $ADD from an exception build file or the point will not load properly.

$AUXUNIT
FF Parameter Source:
Type:
E:UNIT
Lock:
Oper
Default: Null
PtRes: NIM
Range:

None
Auxiliary UnitThe Auxiliary Unit of an alarmable process point. If an
Auxiliary Unit ID is specified, alarms from this point go to the Auxiliary Unit
instead of the Primary Unit. If the $AUXUNIT parameter is set to null (- -),
alarms go to the Primary Unit. Available in Release 520 and later software.

A-Z, 0-9 and Null - (Any valid unit ID as configured in the NCF)
Helpful Hint:

A Network configuration option sets the key level required to change $AUXUNIT.

$BKCLOUD (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: Bad_OOS,
NaN
PtRes: IOP
Range: N/A

R610
11/99

BKCAL_OUT_D
Back-calculated Discrete Output The discrete feedback parameter required
by an upstream block so that the block can take appropriate action under all
downstream conditions. This parameter is intended for regulatory control output
connections.

HPM Parameter Reference Dictionary


Honeywell Inc.

55

$BKCLOUT (FBCM)

$BKCLOUT (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: Bad_OOS,
NaN
PtRes: IOP
Range: N/A

BKCAL_OUT
Back-Calculated Output The feedback parameter required by an upstream
block so that the block can take appropriate action under all downstream
conditions. This parameter is intended for regulatory control output connections.

$BKCLSL1 $BKCLSL3 (FBCM)


FF Parameter Source:
Type:
Blind
Lock:
View
Default: Bad_OOS,
NaN
PtRes: IOP
Range: N/A

BKCAL_SEL1 BKCAL_SEL3
Back-Calculated Outputs associated with SEL1- SEL3 Inputs These are
three separate parameters that are intended to be used with regulatory control
output connections.

$CHKPT01 - $CHKPT27 (SECM, PECM, FBCM)


FF Parameter Source:
Type:
Not Visible
Lock:
Internal User
Default: N/A
PtRes: IOP
Range: N/A

None
Checkpoint Parameter Sets 1-27 The access level applies individually to the
member parameters of the checkpoint parameter set. $CHKPT01 through
$CHKPT27 are 27 different parameters.

$COMCFLM (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
Engineer
10
HPM
0 - 100
Helpful Hint:

56

Comm Processor CPU Free Low Limit in per cent

This parameter cannot be reset.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

$COMCUOS (HPM Box)

$COMCUOS (HPM Box)


Type:
Real
Lock:
View
Default: 0.0
PtRes: HPM
Comm Processor CPU Utilization (System) Specifies the CPU Utilization (in per cent) for the Comm
Processor operating system, device drivers, and interrupt handlers.
Range: 0 - 100
Helpful Hint: This parameter cannot be reset.

$COMCUTS(0) (99) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
0 100

Comm Processor CPU Utilization (Task) CPU Utilization (in per cent) for
each Comm Processor Task.

Helpful Hint: This parameter cannot be reset.

$CTLCFLM (HPM Box)


Type:
Lock:
Default:
PtRes:
Range

Real
Control Processor CPU Free Low Limit
Engineer
10
HPM
N/A
Helpful Hint: This parameter cannot be reset.

$CTLCUOS (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
1 - 100

Control Processor CPU Utilization (system) specifies the CPU Utilization


(in per cent) for the Control Processor operating system, device drivers, and
interrupt handlers

Helpful Hint: This parameter cannot be reset.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

57

$CTLCUTS(0) (99) (HPM Box)

$CTLCUTS(0) (99) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
0 - 100

Control Processor CPU Utilization (Task) specifies the CPU Utilization (in
per cent) for each Control Processor Task

Helpful Hint: This parameter cannot be reset.

$DBVALID (HPM Box)


Type:

E:$ACCSRC
HPM
Database Valid
Lock:
Eng
Default: DB Invalid
PtRes: HPM
Range: 0-DB_Valid (An IOP database is valid and the IOP can be started)
1-DBInvalid (An IOP database is not valid and the IOP will not start)

$IOMPADD(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

58

Integer
View

IOP AddressReturns the physical address of the IOP with (soft address)
(File-1)*16 + card + 127

HPM
0, 129 - 255

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

$OPTOL (RegCtl, AO, FBCM)

$OPTOL (RegCtl, AO, FBCM)


FF Parameter Source:
Type:
Real (%)
Lock:
Engr
Default: 0.0
PtRes: NIM
Range:

None
Output Tolerance Tolerance limit for manually entered OP. The
difference between a new OP and a current OP is compared against
$OPTOL. If the tolerance is violated in either a positive or negative
direction from the current value of OP, operator confirmation is
required before the value is stored. A value of 0.0 disables this check. A
NaN or a negative value is not allowed.

0.0 to 106.9%

$PVFLREC (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: IOP
Range: N/A

None
PV Flag Record This parameter is a parameter set that consists of parameters
BADPVFL and PVFL.

$PVSTREC (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: IOP
Range: N/A

None
PV Status Record The analog input record prefetched from the IOP.

$RBREC (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: Bad_OOS,
Off
PtRes: IOP

READBACK_D
Discrete Readback This parameter is intended for position feedback for
digital valve positioners.

Range: N/A

$RCASOUD (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: Bad_OOS,
NaN
PtRes: IOP
Range: N/A

R610
11/99

RCAS_OUT_D
RCAS Discrete OutputThe discrete feedback parameter required by a
supervisory device so that it can take appropriate action under all downstream
conditions. This parameter is intended to be used for regulatory control output
connections.

HPM Parameter Reference Dictionary


Honeywell Inc.

59

$RCASOUT (FBCM)

$RCASOUT (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: Bad_OOS,
NaN
PtRes: IOP
Range: N/A

RCAS_OUT
RCAS OutputThe feedback parameter required by a supervisory device so
that it can take appropriate action under all downstream conditions. This
parameter is intended to be used for regulatory control output connections.

$ROUTOUT (FBCM)
FF Parameter Source:
Type:
Blind
Lock:
View
Default: Bad_OOS,
NaN
PtRes: IOP
Range: N/A

60

ROUT_OUT
Feedback required by a DDC DeviceThe feedback parameter required by a
direct digital control device so that it can take appropriate action under all
downstream conditions. This parameter is intended for regulatory output
connections

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

$SPTOL (RegCtl, FBCM)

$SPTOL (RegCtl, FBCM)


FF Parameter Source:
Type:
Real (EU)
Lock:
Engr
Default: 0.0
PtRes: NIM
Range:

None
Setpoint ToleranceTolerance limit for manually entered SP in
engineering units. The difference between a new SP and a current SP is
compared against $SPTOL. If the tolerance is violated in either a
positive or negative direction from the current value of SP, operator
confirmation is required before the value is stored. A value of 0.0
disables this check. A NaN or a negative value is not allowed.

>= 0.0

$UCNLSB(1)(50)
Type:
Real
Lock:
View
Default:
PtRes: HPM
Range:

Local UCN Communications Statistics

$UCNLSB(45) (NIM)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
0
HPM, NIM
`0

Local Statistics BlockThe number of auto reconnects.

HPM Parameter Reference Dictionary


Honeywell Inc.

61

AB_DATA1 (SI - Array)

-AAB_DATA1 (SI - Array)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng
NaN
HPM
N/A

Auxiliary A-B Data 1Specifies the Allen-Bradley PLC family type: 2.0, 3.0,
or 5.0. Refer to the APM/HPM Serial Interface Options manual when
configuring for diagnostics.

Helpful Hint:
Use of this parameter is only required to configure Serial Interface mapping to/from an
Allen-Bradley programmable logic controller device. This parameter should be set to NAN if it is not being
used.

AB_DATA2 (SI - Array)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng
NaN
HPM
0 - 999, NaN

Auxiliary A-B Data 2Specifies the Allen-Bradley PLC File Number (in
decimal) from which data is read into the Array point for PLC-3 or PLC-5
controllers. Must be NaN for PLC-2.

Helpful Hint:
Use of this parameter is only required to configure Serial Interface mapping to/from an
Allen-Bradley programmable logic controller device. This parameter should be set to NAN if it is not being
used.

AB_DATA3 (SI - Array)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng
NaN
HPM
0 - 13

Auxiliary A-B Data 3Specifies the data type for Allen-Bradley PLC-2 or
PLC-5 controllers or section ID for PLC-3 controllers. Refer to the APM/HPM
Serial Interface Options manual for additional information.

Helpful Hint:
Use of this parameter is only required to configure Serial Interface mapping to/from an
Allen-Bradley programmable logic controller device. This parameter should be set to NAN if it is not being
used.

62

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

AB_DATA4 (SI - Array)

AB_DATA4 (SI - Array)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng
NaN
HPM

Auxiliary A-B Data 4Specifies the Allen-Bradley PLC scan frequency: 0


indicates that the point is to be scanned as fast as possible. 1255 indicates the
number of seconds for the polling period; 256 = scan once. Note that the report
by exception feature can work with any scan rate selection. Refer to the
APM/HPM Serial Interface Options manual for more information.

0 - 256
Helpful Hint:
Use of this parameter is only required to configure Serial Interface mapping to/from an
Allen-Bradley programmable logic controller device. This parameter should be set to NAN if it is not being
used.

ABHEMSD (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
Off
HPM
On
Off

Abnormal Handler Emergency Shutdown Enable FlagIndicates if the


Emergency Shutdown abnormal handler sequence is currently enabled.

(Emergency Shutdown abnormal handler is enabled)


(Emergency Shutdown abnormal handler not enabled)

ABHHOLD (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
Off
HPM
On
Off

Abnormal Handler Hold Enable FlagIndicates if the Hold abnormal handler


sequence is currently enabled.

(Hold abnormal handler is enabled)


(Hold abnormal handler not enabled)

ABHRSTR (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
View
Off
HPM
On
Off

Abnormal Handler Restart Enable FlagIndicates if the Restart abnormal


handler sequence is currently enabled.

(Restart abnormal handler is enabled)


(Restart abnormal handler not enabled)

HPM Parameter Reference Dictionary


Honeywell Inc.

63

ABHSHDN (ProcMod)

ABHSHDN (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
Off
HPM
On
Off

Abnormal Handler Shutdown Enable FlagIndicates if the Shutdown


abnormal handler sequence is currently enabled.

(Shutdown abnormal handler is enabled)


(Shutdown abnormal handler not enabled)

ACCELTIM (DevCtl)
Type:

Time
Acceleration TimeThe amount of time the SECVAR parameter exceeded the
SVHITP parameter while not in State0. This parameter resets to zero each time
(Duration)
the state transitions to State0.
Lock:
View
Default: 0
PtRes: HPM
Range: 0 to 4000 days (With a resolution of 1 second)

ACCTYPE (Totalizer)
Type:
Lock:
Default:
PtRes:
Range:

E:$ACCTYPE Accumulator Operation ModeSpecifies the type of input.


Eng/PB
Analog
HPM
0-Pulse
Pulse input
1-Analog
Analog input

ACP (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

64

Ent_Id
Advanced Control Point IDDefines the name of the point in the CG or CM to
which this process module is assigned. The NIM notifies the advanced control
PtBld
point when the process module sends a special sequence message.
Null
NIM
Tag name can be up to 16 characters, and the
permissible character set is as follows:
Alphabetic A-Z (uppercase only)
Numeric 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character
or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

ACTPRIM(1)(40) (HPM Box)

ACTPRIM(1)(40) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$ACTPRIM
View

Acting Primary I/O moduleSpecifies the acting primary I/O module.


nn = 140 corresponds to the 40 logical I/O modules.
Applies to primary IOP only.

HPM
0-IOM_A (The A module is the acting primary)
1-IOM_B (The B module is the acting primary)

ACTSCHVR (SECM)
FF Param. Source:
Type: Integer
Lock: View
Default: 0
PtRes: Device
Range: 0 - 65535

MIB: Network Management


ActiveScheduleVersionVersion of currently Active DL Schedule
(LAS).

ACTVSCHD (SECM)
FF Param. Source:
Type:
Integer
Lock:
Eng/PB
Default: 0
PtRes: IOP
Range: 0 - 65535

NMIB: LinkScheduleActivationVariable
Active Version ScheduleContains the Version of the DL Schedule to
be activated. Used to activate a given schedule - Schedule Version
Number.

ADVDEVFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
Advisory Deviation Alarm FlagIndicates whether an advisory alarm has been
detected.
View
Off
HPM
Off
(Alarm has not been detected)
On
(Alarm has been detected. PV - ADVSP is greater than ADVDEVTP)
Helpful Hint:

R610
11/99

ADVDEVFL is never On unless SPOPT = Asp.

HPM Parameter Reference Dictionary


Honeywell Inc.

65

ADVDEVPR

ADVDEVPR
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Advisory Deviation Alarm PriorityDetermines the priority of the advisory


deviation alarm.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint:

ADVDEVPR configuration requires SPOPT = Asp.

ADVDEVTP
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
NaN
HPM
> 0.0
NaN
Helpful Hint:

Advisory Deviation Alarm Trip PointAn alarm will be generated when the
difference between PV and ADVSP exceeds the value in this parameter.

1.
2.

ADVDEVTP change requires SPOPT = Asp .


Alarm generation requires ASPPROC = Enable and
abs(PV - ADVSP) > ADVDEVTP.
When abs(PV - ADVSP) < ADVDEVTP * .9 alarm returns to normal.

ADVSP
Type:
Lock:
Default:
PtRes:
Range:

66

Real
Advisory Setpoint in Engineering Units
Supr
N/A
HPM
SPLOLM to SPHILM
Helpful Hint: ADVSP change requires (SPOPT = Asp) + (ASPPROC = Enable).
Alarm generation requires ASPPROC = Enable and
abs(PV - ADVSP) > ADVDEVTP.
When abs(PV - ADVSP) < ADVDEVTP * .9 alarm returns to normal.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

ADVSPP

ADVSPP
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A
Helpful Hint:

Advisory Setpoint in Percent

ADVSPP cannot be viewed unless SPOPT = Asp.

AKVCRIDX (PECM)
FF Parameter Source:
Type:
Integer
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 1-63

None
Acknowledge VCR IndexThe VCR index of the client VCR that is
used for acknowledging alarts in the FBAP VFD.

ALARMLRS (FBCM)
FF Parameter Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: IOP
Range: N/A

None
Alarms Last Reported Status The last reported status for alarm
information

ALENBST
Type:
Lock:
Default:
PtRes:

E:ALENBST
Oper
Enable
NIM

Range:
Enable
Disable
Inhibit

Alarm Enable StatusDefines the alarm reporting function that is to be used


when an alarm condition is detected in this data point. Note that even when
alarms are disabled, the alarm indicators still appear on the Group and Detail
displays. With Release 510 and later software, the word DIS appears in half
height text above the tag name on the Point Detail or Group Display for a point
with ALENBEST set to Disable.

Displayed
Yes
No
No

Logged
Yes
Yes
No

Reported to EIP
Yes
Yes
No

Helpful Hint: ALENBST should not be set to Disable or Inhibit for points critical to safe
operations. For Box Flag points, this parameter applies to only slots 1
through 128.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

67

ALENBST (FBCM)

Reference:

See Engineers Reference Manual in the Alarm Management section,


for more information on what should happen under different possible alarm
actions.

NOTE
The access lock for the ALENBST parameter is configurable through System-Wide Values.

ALENBST (FBCM)
FF Param. Source:
None
Type:
E:ALENBST Alarm Enable Status
Lock:
Oper
Default: Enable
PtRes: NIM
Range: 0-ENABLE, 1-DISABLE, 2-INHIBIT

ALMOPT (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

E:$ALMOPT Alarming OptionDefines the alarming option for a digital input point whose
DITYPE is Status.
Eng/PB
None
HPM
0-None (No alarms are to be detected.)
1-Offnorml (Off Normal; alarm if current PV state is not the PVNORMAL state. PVNORMAL
is defined by the STATETXT(0) or STATETXT(1) descriptor, as configured by the user.)
2-ChngofSt (An alarm is generated when the digital input changes state in either direction. Note that IOP
firmware must support Change of State Reporting.)
Helpful Hint: ALMOPT configuration requires DITYPE = Status.

ALMINFO (FBCM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: N/A
PtRes: IOP
Range: N/A

68

None
Alarm Information

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

ALPRIOR (ProcMod)

ALPRIOR (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Alarm PriorityDefines the alarm priority for Process Module points. Note
that even when the alarm priority is Journal, the alarm indicators still appear on
Engr
the Group and Detail displays.
Low
NIM
Emergency (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: Access to ALPRIOR is by schematic or CL. ALPRIOR is retained in R500 for
compatibility with earlier software. Use SEQPR for new points.
Reference:

See Engineers Reference Manual in the Alarm Management section,


for more information on what should happen under different possible alarm
actions.

ALPRIOR (DigComp, DigIn, FL)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR
Engr
Low
NIM

Composite Alarm PriorityWhen read, returns a value equal to the highest


configured priority among all alarm parameters for the point. When written, sets
all of the points alarm priority parameters equal to the value being stored. Note
that individual parameters such as BADPVPR, etc. can be stored individually.
If a points separate alarm priorities are all set to the same priority, ALPRIOR is
compatible with R400 and earlier software.
Emergency (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: Access to ALPRIOR is by schematic or CL. No value is actually read from ALPRIOR on
a read and no value is actually stored to ALPRIOR on a write. Values are copied to and from the
separate alarm priorities.
Reference:

R610
11/99

See Engineers Reference Manual in the Alarm Management section,


for more information on what should happen under different possible alarm
actions.

HPM Parameter Reference Dictionary


Honeywell Inc.

69

ALPRIOR (FBCM)

ALPRIOR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
View
Default: Low
PtRes: NIM
Range:

None
Alarm PriorityPriority of the highest priority alarm currently
detected for this point. This value is mapped from the FF alert priority
parameter as follows: Emergency <- 12- 15; High <- 8 - 11; Low <- 5 Network management and System Management; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1
Emergency, High, Low, JnlPrint, Printer, Journal, NoAction

ALVCRIDX (PECM)
FF Parameter Source:
Type:
Integer
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 1-63

None
Alarm VCR Index The VCR list index for accessing the FBAP
alarm object.

ANAME(1)(3) (ProcMod)
Type:
Lock:
Default:
PtRes:

String_8
View
Spaces
HPM

Range:

N/A

Abnormal Sequence NameIndicates the name of the abnormal handler


currently being executed by the process module. A value of " " means that an
abnormal handler is not executing. ANAME(1) returns the abnormal handler
name, while both ANAME(2) and ANAME(3) return the names of the two
abnormal subroutine levels being executed.

AOCALIB(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

70

Logical
Eng/PB

AO Calibration In Progress FlagShows which AO modules are in the process


of calibration.

HPM
Off (No calibration in progress)
On (Calibration in progress)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

APPL (FBCM)

APPL (FBCM)
FF Parameter Source:
None
Type:
E:$DCAPPL Application This parameter indicates the device-control application
by deternining the strings that are annunciated for alarms.
Lock:
Eng/PB
Default: General
PtRes: IOP
Range: 0 General
1 Motor
2 NC Valve
3 NO Valve
4 MOV
5 2-speed motor
6 2-direction motor
7 Elevator
8 Fill
9 Thermal

APVCRIDX (PECM)
FF Parameter Source:
Type:
Integer
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 1-63

None
Application Process VCR Index The VCR list index for accessing
the FBAP data object. This is the VCR list index for the FBAP data
object (VCR list entry) that is associated with the configured devices
FBAP VFD.

ARWNET (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:WINDUP
Windup Status of the InputIndicates the windup status for the SP or another
initializable input.
View
Normal
HPM
0-Normal (Free to move in either direction)
1-Hi (Free to move in the lower direction)
2-Lo (Free to move in the higher direction)
3-HiLo (Not free to move in any direction)

HPM Parameter Reference Dictionary


Honeywell Inc.

71

ARWOP (RegCtl)

ARWOP (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:WINDUP
Windup Status of the OutputIndicates the output (OP) windup status.
View
Normal
HPM
0-Normal (Free to move in either direction)
1-Hi (Free to move in the lower direction)
2-Lo (Free to move in the higher direction)
3-HiLo (Not free to move in any direction)

ASOCSLOT(1-32) (SECM,PECM)
FF Parameter Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: IOP

None
Associated Slot Number For a SECM, this arrayed parameter
defines the CM (PECM) slot numbers associated with a given SECM (2
PECMs per device for a maximum capacity of 10 devices/SECM).
For a PECM, this arrayed parameter defines the CM (FBCM) slot
numbers associated with a given PECM for a maximum capacity of 32
FBCMs/PECM. .

Range: 1-119 for SECM and PECM.

ASSOCCM (PECM, FBCM)


FF Param. Source:
None
Type:
Integer
Associated ModulePECM: This PECM's Associated SECM slot
number. FBCM: This FBCM's Associated PECM slot number.
Lock:
PtBld
Default: NONE
PtRes: IOP
Range: 1-119 for FBCM, 120-127 for PECM

ASSOCDSP
Type:
Lock:
Default:
PtRes:
Range:

String_8
Engr
Blank
NIM
N/A

Associated DisplaySpecifies a user-configured schematic that is associated


with this point. Available on Release 510 and later software.

Helpful Hint: The specified associated display can be called from a Point Detail Display, or from any
summary display or the Group display when the point is selected.

72

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

ASSOCDSP (SECM, PECM, FBCM)

ASSOCDSP (SECM, PECM, FBCM)


FF Param. Source:
Type:
String
Lock:
Engr
Default: N/A
PtRes: NIM
Range: N/A

None
Associated Display:. Specifies a user-configured schematics that is
associated with this point.

ASPPROC (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ASPPROC
Advisory SP Processor State
Supr
Disable
HPM
0-Disable (Disallow advisory deviation alarming)
1-Enable (Allow advisory deviation alarming)
Helpful Hint: ASPPROC change requires SPOPT = Asp.

ASTEP(1)(3) (ProcMod)
Type:
Lock:
Default:
PtRes:

String_8
View
Spaces
HPM

Range:

N/A

Abnormal Step NameASTEP(1) indicates the step name of the abnormal


handler that is executing in this process module. A value of means no
abnormal handler is presently executing. Both ASTEP(2) and ASTEP(3) indicate
the step names of the first and second level subroutines called from the abnormal
handler.

ASTMT(1)(3) (ProcMod)
Type:
Lock:
Default:
PtRes:

Integer
View
Blank
HPM

Range:

0 to 255

Abnormal Statement NumberASTMT(1) indicates the statement number of


the abnormal handler that is presently executing in the process module. Both
ASTMT(2) and ASTMT(3) give statement numbers for first and second level
subroutines executing from an abnormal handler. A value of 0 indicates no
sequence is being executed.

AUTMODFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
Automatic Mode FlagIndicates whether the current mode of the point is
Automatic.
View
N/A
HPM
Off (Current mode is not Automatic)
On (Current mode is Automatic)

HPM Parameter Reference Dictionary


Honeywell Inc.

73

AUXDATA1 (SI-Array Generic Modbus)

AUXDATA1 (SI-Array Generic Modbus)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng
NaN
HPM
1 - 9999, NaN

FTA Driver Auxiliary Data 1Keep Alive Address for Modbus devices.
Specifies the address of a coil that is written to every 10 seconds (Force Single
Coil On function). NaN (dashes) = Keep Alive function is inactive.

Helpful Hint: AUXDATA1 can be configured separately for each Array point. No two Array points
should write to the same coil address. This parameter should be set to NAN if it is not being used.

AUXDATA2 (SI-Array Generic Modbus)


Type:
Lock:
Default:
PtRes:
Range:

Real
FTA Driver Auxiliary Data 2 Specifies the time interval that the FTA waits
before a message retry to the Modbus is attempted. NaN (dashes) indicates a 1.5
Eng
second timeout.
NaN
HPM
.25 - 5 Sec., NaN
Helpful Hint: After three retries, a message timeout error is displayed on the Point Detail display.
AUXDATA2 can be configured separately for each Array point. This parameter should be set to NAN if
it is not being used.

AUXDATA3 (SI-Array Generic Modbus)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng
NaN
HPM

FTA Driver Auxiliary Data 3Signaling mode.Modem support (in


integer/decimal format). Integer = 232 or 485.
(232 = EIA-232, 485 = EIA-485 Multidrop).
Decimal (EIA-232 only) = .0 or .1 (.0 = no modem control, .1 = modem control).
NaN (dashes) = 232.0 (EIA-232 without modem control).
232.0, 232.1, or 485.0
Helpful Hint: All array points that are loaded to the same FTA must have the same
settings. This parameter should be set to NAN if it is not being used.

AUXDATA3

AUXDATA4 (SI-Array Generic Modbus)


Type:
Lock:
Default:
PtRes:
Range:

74

Real
FTA Driver Auxiliary Data 4Baud Rate.Parity (in integer/decimal format).
Baud Rates = 1200, 2400, 4800, 9600, or 19200.
Eng
Parity: .0 = no parity, .1 = odd parity, .2 = even parity.
NaN
NaN (dashes) = 9600.1 = (9600 baud, odd parity).
HPM
integer = 1200, 2400, 4800, 9600, or 19200
decimal = .0, .1, or .2
Helpful Hint: All array points that are loaded to the same FTA must have the same AUXDATA4
settings. This parameter should be set to NAN if it is not being used.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

AV (DigIn)

AV (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Oper
0
HPM
0..32767

Accumulated Value in Engineering UnitsIndicates the current value


accumulated in the accumulator.

AV (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Configurable
0
APM
0..32767

Accumulated Value in Engineering UnitsIndicates the current value


accumulated in the accumulator.

AVDELTHS (PI)
Type:

Integer
The Last Halfseconds AV
Lock:
View
Default: 0
PtRes: HPM
Range: > 0

AVDEV1FL (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
N/A
HPM
Off
On

Accumulated Value; 1st Deviation FlagIndicates whether PVCALC is


greater than AVTV minus AVDEV1TP. (PVCALC > AVTV - AVDEV1TP).
This is the first "slowdown" or "near-target" flag.
(PVCALC is not > AVTV - AVDEV1TP)
(PVCALC is > AVTV - AVDEV1TP)

AVDEV1TP (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Supr
NaN
HPM
> 0.0,
NaN

Accumulated Value; 1st Deviation Trip Point (deviation from AVTV)

HPM Parameter Reference Dictionary


Honeywell Inc.

75

AVDEV2FL (Totalizr)

AVDEV2FL (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
N/A
HPM
Off
On

Accumulated Value; 2nd Deviation FlagIndicates whether PVCALC is


greater than AVTV minus AVDEV2TP. (PVCALC > AVTV - AVDEV2TP).
This is the second "slowdown" or "near-target" flag.
(PVCALC is not > AVTV - AVDEV2TP)
(PVCALC is > AVTV - AVDEV2TP)

AVDEV2TP (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
NaN
HPM
> 0.0,
NaN

Accumulated Value; 2nd Deviation Trip Point (deviation from AVTV)

AVGPU (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average PUsSpecifies the average PUs used for point processing

AVGTF (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
Average Statistics Single Lag Filter Time ConstantDefines the filter time in
the single lag filter used to calculate average values of the performance statistics.
Engineer
1.00 Minutes
HPM
0.0 - 1440.0 (0 = no filter)

AVSTS (PI)
Type:
Lock:
Default:
PtRes:
Range:

76

E:PVVALST
View
Bad
HPM
0-Bad
2-Normal

Value Status of AV

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

AVTV (DigIn)

AVTV (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Oper
0
HPM
0 to 32767

Accumulator Target ValueSpecifies the target value of the accumulator.


AVTV appears on a group or detail display as the SP value.

Helpful Hint: AVTV change requires DITYPE = Accum.

AVTV (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

Real
Oper
NaN
HPM
N/A,
NaN

Accumulator Target ValueSpecifies the target value of the totalizer. AVTV


appears on a group or detail display as the SP value.

AVTVFL
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
View
N/A
HPM
Off
On

Accumulated Value Target Reached FlagAVTVFL is the accumulated


value's "target value reached" flag. It is turned On whenever PVCALC ` AVTV.
Parameter AVTV contains the target value last entered by the operator.

HPM Parameter Reference Dictionary


Honeywell Inc.

77

B (Automan, MulDiv, RatioCtl, RegCtl Summer)

-BB (Automan, MulDiv, RatioCtl, RegCtl Summer)


Type:
Lock:
Default:
PtRes:
Range:

Real
Oper
0.0
HPM
N/A

Overall BiasDefines the overall bias, which consists of BO plus BI. Refer to
the HPM Control Functions and Algorithms manual for a detailed description.

B0 (AutoMan, MulDiv, RatioCtl, RegCtl Summer)


Type:
Lock:
Default:
PtRes:

Real
View
0.0
HPM

Last Operator-Entered Output Bias

B1 (RatioCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
N/A

Output Bias ConstantIf the Calcultr PV algorithm is being used in


conjunction with this algorithm, the value of B1 should be the same as C3.

B2 (RatioCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
N/A

Bias for Input X2If the Calcultr PV algorithm is being used in conjunction
with this algorithm, the value of B2 should be the same as C4.

B1, B2, B3 (MulDiv)


Type:
Lock:
Default:
PtRes:
Range:

78

Real
Supr
0.0
HPM

Bias for Inputs for X1, X2, and X3

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

BADCTLFL

BADCTLFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
Bad-Control Alarm FlagIndicates whether a bad control alarm has been
detected.
View
Off
HPM
Off (Bad-control alarm not present)
On (Bad-control alarm present)

BADCTLOP
Type:
E:$BADCTL

Bad Control OptionIndicates if the mode sheds to manual when bad PV or


CV occurs for regulatory control points. It also shows the value of the output.

O
Lock:
Engr
Default: No_Shed
PtRes: HPM
Range: 0-No_Shed (The point holds its output and mode, resuming control after initialization upon recovery)
1-ShedHold (The mode sheds to manual, the mode attribute goes to operator, while the output is held and external
mode switching is disabled)
2-ShedLow (The mode sheds to manual, the mode attribute goes to operator, while the output goes to -6.9% and
external mode switching is disabled)
3-ShedHigh (The mode sheds to manual, the mode attribute goes to operator, while the output goes to 106.9% and
external mode switching is disabled)
4-ShedSafe (The mode sheds to manual, the mode attribute goes to operator, while the output goes to SafeOP and
external mode switching is disabled. If SafeOP is NaN, the output is held as if the Bad
Control Option is ShedHold.

BADCTLPR
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:ALPRIOR Bad Control Alarm PriorityDefines the priority of the bad control alarm.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergency (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

HPM Parameter Reference Dictionary


Honeywell Inc.

79

BADIOLPF (ProcMod)

BADIOLPF (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Bad IOL PrefetchSet to ON, by the system if any IOL prefetch value is bad.
View
Off
HPM
Off
On (IOL prefetch value is bad)

BADOCFL (RegCtl)
Type:
Lock:
Default:
PtRes:

Logical
View
OFF
HPM

Range:

Off (Point is not in alarm)


On (Point is in alarm)

Bad Output Connection Flag (BADOC) AlarmON indicates that the RegCtl
point cannot drive at least one Analog Output point (out of 4 possible). The
alarm appears on the Alarm Summary display and in the Real Time Journal as a
BADOC alarm. If it is the highest-level alarm on the point, it appears on the
Point Detail or Group displays as BOC.

BADOC1FL
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
OFF
HPM
Off
On

Bad Output Connection Flag 1ON indicates that the RegCtl point cannot
drive Output 1 to an AO point (if configured).

BADOC2FL
Type:
Lock:
Default:
PtRes:
Range:

80

Logical
View
OFF
HPM
Off
On

Bad Output Connection Flag 2ON indicates that the RegCtl point cannot
drive Output 2 to an AO point (if configured).

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

BADOC3FL

BADOC3FL
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
OFF
HPM
Off
On

Bad Output Connection Flag 3ON indicates that the RegCtl point cannot
drive Output 3 to an AO point (if configured).

BADOC4FL
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
OFF
HPM
Off
On

Bad Output Connection Flag 4ON indicates that the RegCtl point cannot
drive Output 4 to an AO point (if configured).

BADOCPR (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR
Engr
Low
NIM
NoAction
JnlPrint
Printer
Journal
Low
High
Emergency

Bad Output Connection (BADOC) Alarm PriorityIndicates the priority of


the Bad Output Connection (BADOC) alarm

Helpful Hint: The value of this parameter can be changed on the Point Detail display with Engineering
keylevel access.

BADOCOPT (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Bad Output Connection Alarm Option (BADOC)ON indicates that the Bad
Output Connection (BADOC) alarm can be generated (or is permitted).
Eng/Pb
OFF
HPM
Off (BADOC alarms are suppressed)
On (BADOC alarms are permitted)
Helpful Hint: The value of this parameter can be changed on the Point Detail display with Engineering
keylevel access.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

81

BADPVFL

BADPVFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
Bad PV FlagIndicates that a bad PV value has been detected at this data point.
For an analog input, a bad PV is defined as a PV whose value is NaN (Not a
View
Number).
Off
HPM
Off (PV is not bad)
On (PV is bad)

BADPVFL (DI)
Type:
Lock:
Default:
PtRes:

Range:

Logical
View
On
HPM

Bad PV FlagIndicates that a bad PV value has been detected at this data point.
BADPVFL is shown on the detailed display only when PNTFORM = Full.
For a Digital Input, the Bad PV Flag is on when:

The PV source is not equal to Manual and DITYPE is set to Accumulator.


The PV source has just been switched to Substituted but the PV has not
yet been updated.
The PV source = Substitute or Auto and PTEXECST = Inactive or the
module is not in the RUN state.
PVSOURCE = Auto and there is no FTA connected or there is a Soft Fail
that is preventing this channel from working.
Off (PV is not bad)
On (PV is bad)

BADPVFL (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Bad PV FlagFor a Digital Composite or Device Control point, the Bad PV
Flag is set to ON when the PV is bad.
View
Off
HPM
Off (PV is not bad)
On (PV is bad)

BADPVFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: IOP
Range: 0-OFF, 1-ON

82

AI: Out_Status.Quality
Bad PV FlagIOP will update this flag based on FFPVSTS.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

BADPVPR

BADPVPR
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Bad PV Alarm PriorityDefines the priority of the bad PV alarm.


Engr
Low
NIM
Emergency (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

BADPVPR (FBCM)
FF Param. Source:
None
Type:
E:ALPRIOR Bad PV Priority:Defines the priority of the BadPV alarm.
Lock:
View
Default: Low
PtRes: NIM
Range: Emergency, High, Low, JnlPrint, Printer, Journal, NoAction

BADPVTXT (DevCtl, DigComp, NIM)


Type:
Lock:
Default:
PtRes:

String_8
PtBld
BAD
NIM

Range:

The permissible character set for the up to eight character descriptor is as follows:
Alphabetic A-Z (upper case only)
Numeric 0-9,
Underscore (_)

Bad PV State DescriptorDefines the state descriptor that is displayed when


the digital composite or device control point state is indeterminate or bad. The
bad state can result when the PV input signals from the process are in an
inconsistent state (e.g., for a valve, the limit switches indicating open and closed
are on at the same time). This state descriptor is configured on a per point basis
and is valid only when the PVTXTOPT parameter is On.

BADSVFL (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
Bad SV Alarm FlagIndicates a bad secondary value alarm.
View
Off
HPM
Off (Good data being read)
On (SV parameter = BAD or NaN)

HPM Parameter Reference Dictionary


Honeywell Inc.

83

BADSVPR (DevCtl)

BADSVPR (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Bad SV Alarm PriorityIndicates the alarm priority for the secondary value.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergency (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

BCAMODFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Backup Cascade Mode FlagIndicates if the mode of the point is Backup
Cascade.
View
N/A
HPM
Off - (point is not in Backup Cascade mode)
On - (point is in Backup Cascade mode)

BCOMPOPT (FlowComp)
Type:
Lock:
Default:
PtRes: HPM
Range:

Bad Compensation Input Option

Set_PVCALC_Bad
Use_Last_Goood_Comp_Term
Use_LastGood_Comp_Input

BFF (PidFf)
Type:
Lock:
Default:
PtRes:
Range:

84

Real
Supr
0.0
HPM
N/A

Feed Forward Input BiasDefines the bias value for multiplication action.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

BHALMFL1BHALMFL7

BHALMFL1BHALMFL7
Type:
Lock:
Default:
PtRes:
Range:

String_2
View

Alarm Flags

NIM
Hexadecimal characters 00 - FF

BIAS (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
BiasDefines the value which is added to the SP.
Oper
0.0
HPM
BSLOLM to BSHILM

BLKDDID (1..2) (PECM, FBCM)


FF Param. Source:
Type:
Integer
Lock:
Engr/PtBld
Default: N/A
PtRes: NIM
Range: N/A

None
Block ID Found in the block header of Function and Resource
Blocks, a unique number which identifies the function of the block.

BLKERRFL (PECM, FBCM)


FF Param. Source:
Type:
Logical
Lock:
View
Default: OFF
PtRes: IOP
Range: OFF
ON

BLOCK_ERR
Block Error Indicator This flag is turned ON when any one of the
possible 16 block errors has been detected in the corresponding fieldbus
function or resource block.

BLK_INFO
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Blind Record
View
N/A
IOP

Function Block Summary InformationProvides Function Block summary


information needed by the NIM for checkpointing

HPM Parameter Reference Dictionary


Honeywell Inc.

85

BLKODIDX (PECM, FBCM)

BLKODIDX (PECM, FBCM)


FF Param. Source:
Type:
Real
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 0 - 65535

Block OD index
Block Object Dictionary IndexStart of Block Information in Object
Dictionary. Resource/Function Block OD index.

BLKTAG (SECM, PECM, FBCM)


FF Param. Source:
Block Tag from FOUNDATION Fieldbus Block Structure
Type:
String
Block Tag This parameter defines the name of the block. The block
Lock:
PtBld
name should be a unique name in the control system because the block
Default: 32 space
tag name will be used throughout system.
characters
PtRes: IOP
Range: All characters in the ASCII character set.

BNDRESET (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Operator
Off
HPM
Off/On

Bounds (Minimum/Maximum) Statistics Reset FlagA write of ON resets


the following maximum/minimum statistics to their default values: HPM CPU
free percentage events, UCN transaction, UCN parameter statistics and UCN
average statistics.

Helpful Hint: A read of BNDRESET always returns OFF.

BNDRSTIM (NIM, HPM Box)


Type:
Lock:

Time
View

Time of Last Bounds (Minimum/Maximum) Statistics Reset.

Default: Time of HPM Startup


PtRes: HPM
Range: N/A
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

86

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

BOXCLR(0)(2) (DevCtl, DigComp)

BOXCLR(0)(2) (DevCtl, DigComp)


Type:
Lock:

E:BOXCOLOR
Eng/PB

Box Color for Digital DisplaysDefines the color of the upper, middle,
and lower boxes that are used to display the current state of the point on the
Group and Detail Displays. The lower box and its default (Red) do not
apply if NOSTATES = 2 for this point.

Default: Green [Upper-box default (State 1)]


Yellow [Middle-box default (State 0)]
Red [Lower-box default (State 2)]
PtRes: NIM
Range: Red
Green
White
Black
Cyan
Yellow
Blue
Magenta
Helpful Hint: BOXCLR has an access lock of View if PNTFORM = Component.

BOXCLR(0)(1) (DigIn, Flag)


Type:
Lock:

E:BOXCOLOR
Eng/PB

Box Color for Digital DisplaysDefines the color of the upper and
lower boxes that are used to display the current state of the point on the
Group and Detail Displays. Boxes are applicable when DITYPE is
Latched or Status.

Default: Green [Upper box default color (State 1)]


Yellow [Lower-box default color(State 0)]
PtRes: NIM
Range: Red
Green
White
Black
Cyan
Yellow
Blue
Magenta

BRDP(1-4095) (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: N/A

R610
11/99

None
Blind Record Data Pipe. This is an arrayed parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

87

BSHILM

BSHILM
Type:
Lock:
Default:
PtRes:
Range:

Real
Bias High LimitDefines the upper limit of the bias.
Supr
50.0
HPM
> BSLOLM,
NaN
Helpful Hint: Entering NaN disables the BSHILM function with NaN being stored in the
database.

BSLOLM
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
-50.0
HPM
< BSHILM,
NaN

Bias Low LimitDefines the lower limit of the bias.

Helpful Hint: Entering NaN disables the BSLOLM function with NaN being stored in the
database.

BYPASS (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Interlock BypassAllows bypassing the permissive and override interlocks
when ON. The Safety Override Interlock (SI0) is not affected. Only applies if
Oper
Override Option (OROPT) is selected.
Off
HPM
Off (Interlocks not bypassed)
On (Interlocks bypassed)

BYPASS (ORSel)
Type:
Lock:
Default:
PtRes:
Range:

88

Logical
Override Input Bypass EnableAllows the operator to select the bypass
function for the X1-X4 inputs.
Oper
Off
HPM
Off (Bypass of inputs is not allowed)
On (Bypass of inputs is allowed)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

BYPASSX1BYPASSX4 (ORSel)

BYPASSX1BYPASSX4 (ORSel)
Type:
Lock:

Bypass X1X4 InputRefer to the HPM Control Functions and Algorithms


manual for a detailed description. BYPASSXn being On does not bypass
X1X4 unless BYPASS = On.
Default: BYPASSX1 = Off
BYPASSX2X4 = On
PtRes: HPM
Range: Off
On

R610
11/99

Logical
Oper

HPM Parameter Reference Dictionary


Honeywell Inc.

89

C (FlowComp, Summer, Totalizer, and VdtLdLg)

-CC (FlowComp, Summer, Totalizer, and VdtLdLg)


Type:
Lock:
Default:
PtRes:
Range:

Real
Scale FactorValue in C is used in the calculation of PVCALC. Refer to the
HPM Control Functions and Algorithms manual for the equation.
Supr
1.0
HPM
Anything except NaN

C1C2 (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
C1 > 0.1
C2 > 0.1

Correction ConstantsValues in C1 and C2 are used in the calculation of


PVCALC, and serve as factors in compensating for assumed design conditions.
Refer to the HPM Control Functions and Algorithms manual for a detailed
description.

C1C2 (PI)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
C1 > 0
C2 > 0

Scaling ConstantsValues in C1 and C2 are used in the calculation of


PVCALC. Refer to the HPM Control Functions and Algorithms manual for a
detailed description.

C1C2 (VdtLdLg)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
> 0.0

Scaling Constant For Input P1P2Values in C1 and C2 are used in the


calculation of TD (fixed time delay) and TDNEW (calculated new delay time).

C1C4 (Calcultr)
Type:
Lock:
Default:
PtRes:
Range:

90

Real
Supr
N/A
HPM
N/A

Intermediate Results of Calculations

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

C1C6 (Summer)

C1C6 (Summer)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
N/A

Scaling Constants 1-6Defines the scaling constants to be used with the


respective inputs P1-P6.

C1C4DESC (Logic)
Type:
Lock:
Default:
PtRes:
Range:

String_8
Custom Alarm DescriptorsDefines the state for each of the four custom
alarms.
Engr
Blank
HPM
8 Character String

C1C4FL (Logic)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Custom Alarm FlagsDefines the state for each of the four custom alarms.
These flags can be written to if C1C4SRC=None.
Program
Off
HPM
Off (A custom alarm is not active)
On (A custom alarm is active)

C1C4PR (Logic)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:ALPRIOR Custom Alarm PrioritiesDefines the alarm priorities for each of the four
custom alarms.
Engr
NoAction
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergency (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

HPM Parameter Reference Dictionary


Honeywell Inc.

91

C1C4SRC (Logic)

C1C4SRC (Logic)
Type:
Lock:
Default:
PtRes:
Range:

E:$LGALSRC Custom Alarm SourceIndicates the alarm source for each of the four custom
alarms.
PtBld
None
HPM
NONE (No source configured for alarms)
L1..L12 (Alarm source is the configured input connection; they can be either On or Off)
SO1..SO24 (Alarm source is the status output (SOn) from another logic block)
FL1..FL12 (Alarm source is a local flag; they can be either On or Off)

CABLESTS (NIM)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Overall Cable Status for a UCN Node
View
N/A
NIM
0-(Both cables are OK)
1-(Cable A has failed)
2-(Cable B has failed)
3-(Both cables have failed)

CALCEXP (Calcultr)
Type:
Lock:
Default:
PtRes:
Range:

String_40
Eng/PB
blank
HPM
N/A

Calculator ExpressionAllows the user to set up an equation that can be up to


40 characters in length, which is to be solved by the Calcultr algorithm. Input
values P1-P6 and intermediate results values C1-C4 can be used in the equation.

CALIBALL (1)(168)
Type:
Lock:
Default:
PtRes:
Range:

92

Logical
Full Calibration Enable Flag
Engr
Off
HPM
Off (Card calibration is disabled)
On (Card calibration is enabled)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CALIBRJ (1)(168)

CALIBRJ (1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Reference Junction Calibration Enable Flag
Eng/PB
Off
HPM
Off (Disable Reference Junction calibration)
On (Enable Reference Junction calibration)

CASIN (FBCM)
FF Param. Source:
Cas_IN
Type:
Blind record Cascade InFF cascade Input parameter. Intended for RegCtl output
connections. only.
Lock:
Prog
Default: Bad, NaN
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text
Helpful Hint:

The data of CASIN cannot be displayed by viewing the parameter directly.


Use FFCSINVL parameter for viewing CASIN's value part and FFCSINST
parameter for viewing CASIN's status part.

CASIND (FBCM)
FF Param. Source:
Cas_IN_D
Type:
Blind
Cascade In DiscreteFF Discrete Cascade Input parameter. Intended
for DigComp and Device Control output connections only.
Lock:
Prog
Default: Bad, Off
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

Helpful Hint:

R610
11/99

The data of CASIND cannot be displayed by viewing the parameter directly.


Use FFCSIDVL parameter for viewing CASIND's value part and FFCSIDST
parameter for viewing CASIND's status part.

HPM Parameter Reference Dictionary


Honeywell Inc.

93

CASMODFL (RegCtl)

CASMODFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Cascade Mode FlagIndicates whether the current mode of the point is
Cascade.
View
N/A
HPM
On - (point is in cascade mode)
Off - (point is not in cascade mode)

CASREQ (AnalgOut, RegCtl)


Type:
Lock:
Default:
PtRes:

E:CASREQ
Prog
NotReq
HPM

Remote Cascade Request FlagDefines whether the remote cascade mode has
been requested for the data point. The remote cascade mode exists when
MODE is changed to Cas and RCASOPT is Ddc or DdcRsp. When a request to
change MODE to Cas is received from a US or a program, MODE does not
immediately change to Cas. Instead, CASREQ is set to Request and a -C
appears to the right of the mode indicator on the Group and Detail displays.
When continuous control in an AM determines that CASREQ contains Request,
it requests the mode to go to Cas, and changes CASREQ to NotReq.
Should the point shed while it is in the remote cascade mode, MODE goes to the
state defined in SHEDMODE, and CASREQ goes back to Request.

Range:

0-NotReq
1-Request

(Remote cascade mode request not made)


(Remote cascade mode request made; operator or program has requested the
cascade mode)

Helpful Hint: CASREQ does not apply for an AnalgOut point if RCASOPT = None.
CASREQ does not apply for a RegCtl point unless RCASOPT = Spc, Ddc,
or DdcRsp.
If Spc has been entered for the RCASOPT parameter, the AM writes to the setpoint.
Ddc is the only remote cascade option for an analog output point.

CFGCMD (PECM)
FF Param. Source:
Type:
E:$CFGCMD
Lock:
PtBld/Eng
Default: NULL
PtRes: IOP
Range:

94

None
Configuration CommandThese commands are used for
handshaking between the TPS Builder and the fieldbus IOP during
clear/load device configuration data sequences. These commands can
only be initiated by the TPS Builder and can only be read by the IOP.
Caution: Writing to this parameter for reasons other than
described will cause IOP/device communication failures

0 Null
1 CFG_STRT
2 CFG_DONE

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CFGSTAT (PECM)

CFGSTAT (PECM)
FF Param. Source:
None
Type:
E:$CFGSTAT Configuration Command StatusThis parameter displays the status
of a write operation to the CFGCMD parameter described above..
Lock:
View
Default: NULL
PtRes: IOP
Range: 0 Null
1 CFG_STRT
2 CFG_DONE

CFLNKSET (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: N/A

Network Management Information Block


Configured Link SettingDlmeLinkSettings.

CHPINHWY (UCN)
Type:
Lock:
Default:
PtRes:
Range:

Automatic Checkpoint Inhibit


E:CHPINDAC
Supr
Enable
NIM
0-Enable (Enable automatic checkpointing of databases on this UCN)
1-Inhibit (Inhibit automatic checkpointing)

CHPINOPR (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Automatic Checkpoint Inhibit OperationDefines whether automatic


E:CHPINDAC
database saves are to be performed for the devices connected to this NIM.
Supr
Enable
NIM
Enable (Automatic database saves are enabled)
Inhibit (Automatic database saves are inhibited)

HPM Parameter Reference Dictionary


Honeywell Inc.

95

CIDSTN(1)CIDSTN(4) (RegCtl)

CIDSTN(1)CIDSTN(4) (RegCtl)
Type:
Prm_ID
Lock:
PtBld
Default: Based on
CTLALGID,
CTLEQN, N
PtRes: HPM
Range: N/A

Control Input Connection DestinationDefines the parameter name (PV, SP,


etc.) in the RegCtl point that is to receive the value fetched using the
"Tagname.Parameter" or the hardware reference address specified in parameter
CISRC, Control Input Connection Source.

Helpful Hint: 1.
2.

CIDSTN must contain a legitimate parameter of one to eight characters.


Default to PV, SP, or some other parameter depends on parameters
CTLALGID, CTLEQN, and M.

CISRC(1)CISRC(4) (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Ent.Prm
Control Input Connection SourceDefines the "Tagname.Parameter" of the
parameter whose value is to be obtained and then stored in one of up to four
PtBld
RegCtl algorithm inputs. Refer to the HPM Control Functions and Algorithms
null.null
manual for a detailed description.
HPM
Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters, and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.

CLBACK (ProcMod)
Type:
Lock:
Default:
PtRes
Range:

96

Integer
Engr
0
HPM
(0 - 240)

Number of Backward Branches -- Specifies how many backward branches


may occur when executing GOTO WHEN ERROR, & REPEAT, before
preemption occurs. 0 = preempt every backward branch.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CLPZMXC (UCN)

CLPZMXC (UCN)
Type:
Lock:
Default:
PtRes
Range:

Logical
Overall Cable Status for UCN Cable A
View
N/A
NIM
Off (Cable A status is OK)
On (Cable A status is not OK)

CLPZMXP (UCN)
Type:
Lock:
Default:
PtRes
Range:

Logical
Overall Cable Status for UCN Cable B
View
N/A
NIM
Off (Cable B status is OK)
On (Cable B status is not OK)

CMD (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
Command Fail Alarm FlagIndicates if the PV failed to move after the output
Configurable command within the allowed command fail time. Command Fail Alarm priority
is determined by CMDDISPR.
Off
APM
Off (PV moved after the output command)
On (PV did not move after the output command)

HPM Parameter Reference Dictionary


Honeywell Inc.

97

CMDDISFL (DevCtl, DigComp)

CMDDISFL (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Command Disagree Alarm FlagIndicates whether a field device did not go
to the commanded state within the allowed feedback time.
View
Off
HPM
Off (No command disagree alarm)
On (Command disagree alarm has been detected by this point)
Helpful Hint: A slow-responding field device can cause a premature alarm. If so, adjust the
time in parameter FBTIME.

CMDDISPR (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range

E:ALPRIOR Command Disagree Alarm PriorityDefines the alarm priority of command


disagree, command fail, and uncommanded change alarms.
Engr
Low
NIM
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

CMDFALFL (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

98

Logical
Command Fail Alarm FlagIndicates if the PV failed to move after the output
command within the allowed command fail time. Command Fail Alarm priority
View
is determined by CMDDISPR.
Off
HPM
Off (PV moved after the output command)
On (PV did not move after the output command)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CMDFALTM (DevCtl, DigComp)

CMDFALTM (DevCtl, DigComp)


Type:
Lock:

Integer
Command Fail TimeoutSets the amount of time (in seconds) that the
point should wait before generating a command fail alarm, if the PV has
Supr if
not changed after changing the output. Command Fail Alarm priority is
CMDFALTM
determined by CMDDISPR.
is changed
from a nonzero value to a
zero value,
else Eng/PB
Default: 0
PtRes: HPM
Range: 0 to 999 seconds (0 indicates command fail alarming is disabled)

CMDHWREV
Type:
Lock:
Default:
PtRes:
Range:

String_2
View

HPMM Communications Daughter Card Revision

HPM
Hexadecimal characters 00 - FF

CMFLTIME (HPM BOX)


Type:
Lock:
Default:
PtRes:
Range:

Time
View
N/A
HPM

HPMM Communications Failure Time

Helpful Hint: If a value of 0 is returned for the time from the UCN, a parameter status of Parameter
Invalid is returned on the LCN.

CMIDTXT (HPM BOX)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

String_16
HPMM Communications Identification Text String
View
Blank
HPM
Hexadecimal characters 00 - FF

HPM Parameter Reference Dictionary


Honeywell Inc.

99

CMTYPE (SECM, PECM, FBCM)

CMTYPE (SECM, PECM, FBCM)


FF Param. Source:
None
Type:
E:$CMTYPE Control Module Type This parameter defines whether the control
module is a SECM, PECM, or FBCM.
Lock:
PtBld
Default: Not
Configured
PtRes: IOP
Range: 0 Null (Not Configured)
1 PECM
2 SECM
3 FBCM

CMPLTIME
Type:
Lock:
Default:
PtRes:
Range:

Time
View
0
HPM

Compile TimeSpecifies the sequence compile time (CL object header)

CNFERRFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
Off
HPM
Off
On

Configuration Error FlagThis flag is set if any configuration requirement is


violated.

CNFERRPR
Type:
Lock:
Default:
PtRes:
Range:

E: ALPRIOR Configuration Error Priority


Eng/PB
Low
HPM
Low

CNFLUA(n)
Type:
Lock:
Default:
PtRes:
Range:

100

Real
View
0.0
HPM

Configured Link Units on Link A


n = 1 - 64 for per cycle totals
n = 257 - 320 for per cycle non-SI IOP loading
n = 513 - 576 for per cycle SI array slot loading

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CNFLUB(n)

CNFLUB(n)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM

Configured Link Units on Link B


n = 1 - 64 for per cycle totals
n = 257 - 320 for per cycle non-SI IOP loading
n = 513 - 576 for per cycle SI array slot loading

CNFMU
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM

Configured Memory UnitsConfigured size of slot in Memory units.

CNFPU(1 - 64) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM

Configured Process Units Per Cycle

CNFPU
Type:
Lock:
Default:
PtRes:
Range:

Real
PtBld
2.0
HPM

Configured Process Units Per CycleProcess Units Configured as being


required to execute point processing.

Helpful Hint: Can only be written for ProcMod points.

CNFPUP (1 -64)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
0
HPM

Configured PUs PercentSpecifies the Configured Process Units in percent

HPM Parameter Reference Dictionary


Honeywell Inc.

101

CNTLLOCK

CNTLLOCK
Type:
Lock:
Default:
PtRes:

E:ACCLVL
Engr
OPERATOR
HPM

Control LockAttempts to write values in the following parameters are


subject to the access-lock value contained in CNTLLOCK. The check is
bypassed for the exceptions.
Parameter
PROCMOD
SEQEXEC
SEQMODE
OVERPHAS
OVERSTEP
OVERSTAT

Range:

Exceptions
New value = START
None
None
SEQEXEC = FAIL or ERROR
SEQEXEC = FAIL or ERROR
SEQEXEC = FAIL or ERROR

0-OPERATOR - Operator and higher keylock positions allow store access.


1-SUPERVIS - Supervisor and higher keylock positions allow store access.
2-ENGINEER - Engineer and higher keylock positions allow store access.
3-PROGRAM - Only the program has store access.

CODSTN(1)CODSTN(4) (RegCtl)
Type:

Universal
Control Output Connection DestinationDefines up to four different
"Tagname.Parameter" or hardware reference address destinations to which the
Ent.Prm
output value from RegCtl point is to be written. Refer to the HPM Control
Lock:
PtBld
Functions and Algorithms manual for a detailed description.
Default: null.null
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters, and the permissible
character set is as follows:
Alphabetic A-Z (uppercase only)
Numeric 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as AO (analog output)
mm is the IOP Card number (1-40)
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

COMCFAVG (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

102

Real
Average HPM Communication CPU Free PercentageThe average
View
percent of time the Communications Processor is not busy.
NaN
HPM
0 - 100
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

COMCFMAX (HPM Box)

COMCFMAX (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
Maximum HPM Communication CPU Free PercentageThe maximum
View
percent of time the Communications Processor is not busy.
NaN
HPM
0 - 100
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

COMCFMIN (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
0 - 100

Minimum HPM Communication CPU Free PercentageThe minimum


percent of time the Communications Processor is not busy.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

COMDAUGH
Type:
Lock:
Default:
PtRes:
Range:

Logical
View

HPMM Communications Daughter Card Present Flag.

HPM
Off (No daughter card present)
On (Daughter card present)

COMDAY
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
1 - 31

Creation Day of HPMM Communications Personality.

COMFWREV
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

String_2
View

HPMM Communications Firmware Revision.

HPM
Hexadecimal characters 00 - FF

HPM Parameter Reference Dictionary


Honeywell Inc.

103

COMDGAVG (HPM Box)

COMDGAVG (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM

Average Diagnostic cycle time (in minutes) in the Comm CPU

COMDGMAX (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM

Maximum Diagnostic cycle time (in minutes) in the Comm CPU

COMHOUR (HPM BOX)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM

HPMM Communications Personality Creation Date-Hour

COMHWREV
Type:
Lock:
Default:
PtRes:
Range:

String_2
View

HPMM Communications Hardware Revision.

HPM
Hexadecimal characters 00 - FF

COMLUAVG (1) - (2) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

104

Real
View
0.0
HPM
0 - 100

Average HPM IOL Utilization (in Percent) by the Comm CPU, per I/O
Link

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

COMLUMAX (1) - (2) (HPM Box)

COMLUMAX (1) - (2) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
0 - 100

Maximum HPM IOL Utilization (in Percent) by the Comm CPU, per I/O
Link

COMMAND (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

E:COMMAND
Accumulator CommandsAllow the operator to control the accumulator.
Oper
None
HPM
0-None (No effect on accumulator)
1-Start (Start the accumulator)
2-Stop (Stop the accumulator)
3-Reset (Reset the accumulation to zero)
Helpful Hint: COMMAND applies only when DITYPE = Accum.

COMMAND (STI)
Type:

CommandAllows the user to do database transfers between the STI point and
E:COMMAN the smart transmitter, and to calibrate the transmitter.

D
Lock:
Oper
Default: None
PtRes: HPM
NOTE
During an up-load operation, previously unseen data is read from the transmitter database
and stored in the STI database. If this data is not desired, the data can be restored by using the
checkpoint restore or load IDF functions.

Range:

0-None (A command has not been issued by the STI point)


1-DnLoadDb (Loads the transmitter parameters from the STI point data base into the transmitter)
2-UpLoadDb (Loads the transmitter data base from the transmitter into the STI point)
3-Set_LRV (Sets the Lower Range Value)
4-Set_URV (Sets the Upper Range Value)
5-Cor_LRV (Corrects the Lower Range Value)
6-Cor_URV (Corrects the Upper Range Value)
7-Cor_Inpt (Corrects the zero point for the PV value)
8-RstCor (Sets all input calibration parameters to their default values)
Helpful Hint: If PV or PV_SV has been entered for the DECONF parameter, the only command
supported is DnLoadDB.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

105

COMMAND (Timer)

COMMAND (Timer)
Type:
Lock:
Default:
PtRes:
Range:

E:COMMAND
Timer CommandsAllow the operator to control the operation of the timer
data point.
Oper
None
HPM
0-None (No effect on the timer)
1-Start (Starts the timer)
2-Stop (Stops the timer)
3-Reset (Resets the timer to zero)
4-RestStrt (Resets the timer, then starts the timer)

COMMAND (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

E:COMMAND
Totalizer CommandsAllow the operator to control the operation of the
totalizer.
Oper
None
HPM
0-None (No effect on totalizer)
1-Start (Starts the totalizer)
2-Stop (Stops the totalizer)
3-Reset (Resets the totalizer to RESETVAL)

COMMIN (HPM BOX)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM

HPMM Communications Personality Creation Date-Minute

COMMONTH
Type:
Lock:
Default:
PtRes:
Range:

106

Integer
View
N/A
HPM
1 - 12

Creation Month of HPMM Communications Personality

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

COMNAME

COMNAME
Type:
String_8
Lock:
View
Default:
PtRes: HPM
Range:

HPMM Communications Personality Name

COMPHILM (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Compensation Term High LimitDefines the upper limit of the COMPTERM
(compensation term) parameter.
Supr
1.25
HPM
COMPLOLM to 10.0,
NaN
Helpful Hint: Entering NaN disables high-limit checking by forcing its value to the extreme
(10.0).

COMPLOLM (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Compensation Term Low LimitDefines the lower limit of the COMPTERM
(compensation term) parameter.
Supr
0.8
HPM
0.0 to COMPHILM,
NaN
Helpful Hint: Entering NaN disables low-limit checking by forcing its value to the extreme
(0.0).

COMPTERM (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Compensation TermThis term differs in each of the five flow compensation
equations, A through E. Refer to the HPM Control Functions and Algorithms
View
manual for a detailed description.
1.0
HPM
COMPLOLM to COMPHILM

HPM Parameter Reference Dictionary


Honeywell Inc.

107

COMRDRRV

COMRDRRV
Type:
Integer
Lock:
View
Default:
PtRes: HPM
Range:

Rdr Revision

COMRDRVS
Type:
Integer
Lock:
View
Default:
PtRes: HPM
Range:

Rdr Version

COMREV
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
N/A

HPMM Communications Software Revision

COMVERS
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
N/A

HPMM Communications Software Version

COMYEAR
Type:
Lock:
Default:
PtRes:
Range:

108

Integer
View
N/A
HPM
0 - 99

Creation Year of HPMM Communications Personality

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CONTCUT

CONTCUT
Type:
Lock:
Default:
PtRes:

Logical
Prog
Off
HPM

Contact Cut Out Defines whether alarms detected at this data point are to be
cut out to prevent this data point's alarms from being reported to the operator.
The alarms continue to be reported to the AM or CM through the EIPPCODE
parameter.
CONTCUT can be used to cutout alarms on a point when the alarms are
generated because of specific conditions at other points which themselves have
alarms. As an example, the user could configure a logic point so that the logic
point would monitor the nuisance alarm conditions and then store the contact
cutout state of this point using an output connection. It can also be stored by the
sequence program in the HPM or the AM which could monitor the process
conditions to determine when the alarms have to be suppressed.

Range:

Off (Alarms are not cut out)


On (Alarms are cut out)
Helpful Hint: Cutout alarms behave the same as inhibited alarms; that is, when a point's
contact cutout state is true
alarms are not distributed to the US or HM
return to normal events are not distributed to the US or HM
EIP events triggered by the alarm condition are not distributed
For HPM Box Flag points, CUTOUT applies to only slots 1128.

CONTCUT (FBCM)
FF Param. Source:
Type:
Logical
Lock:
Prog
Default: Off
PtRes: IOP
Range: 0-OFF, 1-ON

R610
11/99

None
Contact Cut OutDefines whether alarms detected at this data point
are to be cut out to prevent this data point's alarms from being reported
to the operator.

HPM Parameter Reference Dictionary


Honeywell Inc.

109

COUNTDWN (DigIn)

COUNTDWN (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Eng/PB
Off
HPM
Off
On

Accumulator Count Down FlagDetermines whether the accumulator is to


count down or count up.

(Accumulator is to count up)


(Accumulator is to count down)

Helpful Hint: COUNTDWN configuration requires DITYPE = Accum.

CPMSGSEC (NIM PSDP)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
NIM
N/A

Number of Checkpoint MessagesSpecifies the Number of Checkpoint


Messages per second.

CPTIMAVG (NIM PSDP)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
NIM
N/A

Average Time to Complete a Checkpoint RequestSpecifies the Average


Time (in msec.) to Complete a Checkpoint Request.

CPTIMMAX (NIM PSDP)


Type:
Lock:
Default:
PtRes:
Range:

110

Real
View
0
NIM
N/A

Maximum Time to Complete a Checkpoint RequestSpecifies the Maximum


Time (in msec.) to Complete a Checkpoint Request.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CRIOLORN (1) - (4) (HPM Box)

CRIOLORN (1) - (4) (HPM Box)


Type:
Lock:
Default:
PtRes:

Integer
View
0
HPM

Current Hour IOL Fetch/Store Overrun CounterA counter that


accumulates and shows the number of I/O Link fetch/store time outs that have
occurred during the current hour.
In arrays 1 through 4, the counter is indexed by the cycle.
In array 0, the counter is totaled for all cycles.

Range:

>0

CRPPXORN (0 - 8) (HPM Box)


Type:
Lock:
Default:
PtRes:

Integer
View
0
HPM

Current Period Point Processing Overruns Per CycleA counter that


accumulates and shows the number of HPMM point processing overruns that
have occurred during the current hour.
In arrays 1 through 8, the counter is indexed by the cycle
In array 0, the counter is totaled for all cycles.

Range:

>0

CRUCNORN (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

Current-Hour UCN Access Overruns Indicates the number of UCN access


overruns that have occurred in the current hour. Refer to the HPM Control
Functions and Algorithms manual for a detailed description of overrun handling.

CTFLTIME (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Time
View
N/A
HPM
N/A

HPMM Control Failure Time

Helpful Hint: If a value of 0 is returned for the time from the UCN, a parameter status of Parameter
Invalid is returned on the LCN.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

111

CTIDTXT (HPM BOX)

CTIDTXT (HPM BOX)


Type:
Lock:
Default:
PtRes:
Range:

String_16
View
Blank
HPM
N/A

HPMM Control Functionality ID Text String

CTLACTN
Type:
Lock:
Default:
PtRes:
Range:

E:POLARITY Control ActionDefines the direct/reverse action of this algorithm's output.


Eng/PB
Reverse
HPM
0-Direct (As PV increases, output increases)
1-Reverse (As PV increases, output decreases)

CTLALGID (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:$PMMCTAL
Control Algorithm IdentifierDefines the algorithm that is to be used
for this RegCtl point.
PtBld
Null
HPM
0-Null (No algorithm selected)
1-Pid (Proportional, Integral, Derivative)
2-PidFf (PID with Feedforward)
3-PidErfb (PID with External Reset Feedback)
7-RatioCtl (Ratio Control)
8-RampSoak (Ramp Soak)
9-AutoMan (Auto Manual Station)
10-IncrSum (Incremental Summer)
11-Switch (Switch)
12-ORSel (Override Selector)
13-PosProp (Position Proportional)
14-PIDPosProp (PID with Position Proportional output)

CTLCFAVG (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
0 - 100

Average HPM Control Processor CPU Free PercentageThe average


percent of time the HPM Control Processor is not busy.

Helpful Hint: This statistic can be viewed on the Toolkit Displays

112

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CTLCFMAX (HPM Box)

CTLCFMAX (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
Maximum HPM Control Processor CPU Free PercentageThe maximum
percent of time the HPM Control Processor is not busy.
View
NaN
HPM
0 - 100
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

CTLCFMIN (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
0 - 100

Minimum HPM Control Processor CPU Free PercentageThe minimum


percent of time the HPM Control Processor is not busy.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

CTLDAY
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
1 - 31

Creation Day of HPMM Control Personality

CTLDGAVG (1) - (2) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
N/A

Average Diagnostic cycle time (in minutes) in the Control CPU

CTLDGMAX (1) - (2) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
0.0
HPM
N/A

Maximum Diagnostic cycle time (in minutes) in the Control CPU

HPM Parameter Reference Dictionary


Honeywell Inc.

113

CTLEQN (AutoMan)

CTLEQN (AutoMan)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
Control Equation Type
Eng/PB
EqA
HPM
0-EqA (CV = X1 + B +BI)
1-EqB (CV = X1 + (K*X2) + BI)

CTLEQN (ORSel)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
Control Equation TypeDefines whether the highest or the lowest input is
to be selected.
PtBld
EqA
HPM
0-EqA (Selects the highest input)
1-EqB (Selects the lowest input)

CTLEQN (Pid)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
Control Equation TypeDefines how Proportional (P) or gain, Integral (I)
or reset, and Derivative (D) action is applied to a PID-type algorithm's
PtBld
calculated Error (PV - SP).
EqA
HPM
0-EqA (P, I, and D act on Error)
1-EqB (P and I act on Error, D acts on PV)
2-EqC (I acts on Error, P and D act on PV)
3-EqD (Integral-only control)

CTLEQN (Switch)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
Control Equation TypeDefines whether the operator, the user-written
program, or the logic slot controls the selection of one of the four inputs
Eng/PB
(X1-X4) as the input to this algorithm.
EqA
HPM
0-EqA (Operator controls switch position)
1-EqB (Program or logic point controls switch position)

CTLHOUR (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

114

Integer
View
0
HPM
N/A

HPMM Control Personality Creation Date-Hour

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CTLMIN (HPM Box)

CTLMIN (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
N/A

HPMM Control Personality Creation Date-Minute

CTLMONTH
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
1 - 12

Creation Month of HPMM Control Personality

CTLNAME
Type:
Lock:
Default:
PtRes:
Range:

String_8
View
N/A
HPM
N/A

HPMM Control Personality Name

CTLOPT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Logical
HPMM Control Processor Option
PtBld
On
HPM
On (All point types can be configured)
Off (DigComp, Logic, RegCtl, or RegPV points cannot be configured; only I/O points can be configured.
This usually means that the control processor hardware is missing from the HPM).

CTLREDUN
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
View
N/A
HPM
Off
On

HPMM Control Redundancy Present Flag

HPM Parameter Reference Dictionary


Honeywell Inc.

115

CTLREV

CTLREV
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
N/A

HPMM Control Personality Revision

CTLVERS
Type:
Lock:
Default:
PtRes:
Range:

Integer
View

HPMM Control Personality Version

HPM
N/A

CTLYEAR
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 - 99

Creation Year of HPMM Control Personality

CTRLINIT (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

116

Logical
Prog
Off
HPM
Off
On

Control Initialization Request FlagA user-written program or a logic slot


can cause a data point to initialize by setting the point's control initializationrequest flag to On.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CURCOMFL

CURCOMFL
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$PMMHFST
View

Current HPMM Communications Board Failure

HPM
Null (Unknown Error)
Pwrdwn (Power Down )
Lr_Par (Parity Error)
Lr_Lram (Local Ram Error)
Lr_Ck (Local Ram Check)
Lr_Exc (Local Ram Exception)
Lr_Hrev (Local Ram Hardware Revision)
Mm_Hrev (Memory Board Hardware Revision)
Lr_Tmr (Local Ram Timer Error)
Lr_Ptrn (Local Ram Pattern Check Error)
Lr_Byte (Local Ram Byte Error)
Lr_Adcd (Local Ram Address Decode Test)
Lr_Addl (Local Ram Additional Check)
Lr_Clrr (Local Ram Scrub Incomplete)
Sr_Par (Shared Ram Parity)
Sr_Ptrn (Shared Ram Pattern Check Error)
Sr_Adcd (Shared Ram Address Decode Test)
Sr_Addl (Shared Ram Additional Checks)
Gr_Par (Global Ram Parity)
Gr_Ptrn (Global Ram Pattern Check Error)
Gr_Byte (Global Ram Byte Error)
Gr_Adcd (Global Ram Address Decode Test)
Gr_Addl (Global Ram Additional Checks)
Gr_Clrr (Global Ram Scrub Incomplete)
31_Nr (IOL Processor, No Response or Failure)
31_Aliv (IOL Processor, Transmitter Not Alive)
31_Iltn (IOL Processor, Illegal Transition)
Nmi_Unk (Unknown NMI Request)
Baducnn (UCN Address Parity or Duplicate Address)
Nr (No Response From Other Processor)
Mrft (Memory Reference Table (Pattern Build Fail)
Nomtos (No MTOS Readout)
Llc_Comm (LLC Communication Fatal Error)
Ucndrv (UCN Driver, Fatal Error)
Rd_Hrev (Redundancy Card Version/Revision Mismatch)
Sw_Error (Software Error)
Md_Hrev (Modem Card Version/Revision Mismatch)
Da_Ptrn (Daughter Card Pattern Test)
Da_Byte (Daughter Card Byte Write Test)
Da_Adcd (Daughter Card Address Decode)
Da_Addl (Daughter Card Additional Test)
Da_Clrr (Daughter Card Scrub Incomplete)
Rd_Snps (Redundancy Card 96 Kw Snapshot Error)
Rd_Bslk (Redundancy Card Bus Lock Fail)

HPM Parameter Reference Dictionary


Honeywell Inc.

117

CURCTLFL

CURCTLFL
Type:
Lock:
Default:
PtRes:
Range:

118

E:$PMMHFST
View

Current HPMM Control Failure

HPM
Null (Unknown Error)
Pwrdwn (Power Down )
Lr_Par (Parity Error)
Lr_Lram (Local Ram Error)
Lr_Ck (Local Ram Check)
Lr_Exc (Local Ram Exception )
Lr_Hrev (Local Ram Hardware Revision)
Mm_Hrev (Memory Board Hardware Revision)
Lr_Tmr (Local Ram Timer Error)
Lr_Ptrn (Local Ram Pattern Check Error)
Lr_Byte (Local Ram Byte Error)
Lr_Adcd (Local Ram Address Decode Test)
Lr_Addl (Local Ram Additional Checks)
Lr_Clrr (Local Ram Scrub Incomplete)
Sr_Par (Shared Ram Parity)
Sr_Ptrn (Shared Ram Pattern Check Error)
Sr_Adcd (Shared Ram Address Decode Test)
Sr_Addl (Shared Ram Additional Checks)
Gr_Par (Global Ram Parity)
Gr_Ptrn (Global Ram Pattern Check Error)
Gr_Byte (Global Ram Byte Error)
Gr_Adcd (Global Ram Address Decode Test)
Gr_Addl (Global Ram Additional Checks)
Gr_Clrr (Global Ram Scrub Incomplete)
31_Nr (IOL Processor, No Response or Failure)
31_Aliv (IOL Processor, Transmitter Not Alive)
31_Ilatn (IOL Processor, Illegal Transition)
Nmi_Unk (Unknown NMI Request)
Baducnn (UCN Address Parity or Duplicate Address)
Nr (No Response From Other Processor)
Mrft (Memory Reference Table - Pattern Build Fail)
Nomtos (No MTOS Readout)
Llc_Comm (LLC Communication Fatal Error)
Ucndrv (UCN Driver, Fatal Error)
Rd_Hrev (Redundancy Card Version/Revision Mismatch)
Sw_Error (Software Error)
Md_Hrev (Modem Card Version/Revision Mismatch)
Da_Ptrn (Daughter Card Pattern Test )
Da_Byte (Daughter Card Byte Write Test )
Da_Adcd (Daughter Card Address Decode)
Da_Addl (Daughter Card Additional Tests)
Da_Clrr (Daughter Card Scrub Incomplete)
Rd_Snps (Redundancy Card 96 Kw Snapshot Error)
Rd_Bslk (Redundancy Card Bus Lock Fail)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CURIOLFL

CURIOLFL
Type:
Lock:
Default:
PtRes:
Range:

E:$IOMHF
View

Current HPMM IOL Interface Failure

HPM
Unknown - (Unknown Error)
Powerdwn - (Power Is Off)
Invprgex (Invalid Program Execution)
Epromerr (EPROM Error)
Ramcnter (Ram Contents Error)
Ramadrer (Ram Address Error)
Dpaerror (Device Physical Address Error)
Dsaerror (Device Soft Address Error)
Rxbufofl (Receive Buffer Overflow Error)
Ioljaber (IOL Jabber Error; Module saw or talked too much on link)
Badpgjmp (Bad Program Jump)
Adcincmp (A/D Incompatible)
Adoutovf (A/D Overflow)
Adoutudf (A/D Underflow)
Adccaler (A/D Calibration Error)
Baddcltc (Bad DC LTC)
Dmt_tmot (Deadman Time Out)
Mltoutfl (Multiple Output Failure)
Datbusfl (Data Bus Failure)
Baddarng (Bad A/D Range)
Mstrtmot (Master Timeout)
Ctrcktfl (Counter Circuit Failure)

CURPINAM (n)
Type:
Lock:
Default:
PtRes:
Range:

String_8
View
N/A
IOP
N/A

Current PI FilenameDefines the personality Image filename that


currently resides in this IOP where n is the IOP number 1 - 40.

CURSEGID (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:CURSEGID
Current Segment IDDefines the current ramp or soak segment.
Oper
Ramp1
HPM
0-Ramp1
1-Soak1
2-Ramp2
3-Soak2
:
and
:
20-Ramp11 21-Soak11
22-Ramp12 23-Soak12

HPM Parameter Reference Dictionary


Honeywell Inc.

119

CUTOFFLM (Totalizr)

CUTOFFLM (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

Real
Zero-Flow Cutoff LimitAllows the user to specify a cutoff limit such that
when the value of input parameter P1 falls below the limit specified, its value is
Supr
replaced by 0.0.
0.0
HPM
> 0.0,
NaN (Cutoff limit is not applicable)

CUTOFFLM (VdtLdLag)
Type:
Lock:
Default:
PtRes:
Range:

Real
Zero-Flow/Belt-Speed Cutoff LimitAllows the user to specify a cutoff limit
for equations C and D.
Supr
NaN
HPM
> 0.0,
NaN (Bypasses the limit check)

CV
Type:
Lock:
Default:
PtRes:
Range:

Real
Prog
NaN
HPM
N/A

Calculated VariableThe result (calculated value) of the calculation of the


control algorithm. The value can be in percent or in engineering units depending
on the control algorithm.

CVEUHI
Type:
Real
Lock:
Engr
Default: 100.0
(GPM,
PPH, etc.)
PtRes: HPM
Range: > CVEULO

Calculated Value's High Limit in Engineering Units

Helpful Hint: CV ranges track X-input ranges if CTLALGID = AutoMan, ORSel, IncrSum,
or Switch. For CTLALGID = PidErfb and RampSoak, CV ranges are configurable. For
CTLALGID = Pid, Pidff, and RatioCtl, if NOCOPTS = 0, then the CV ranges are
configurable, otherwise, the CV ranges track the ranges of the secondary output
connection.

120

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

CVEUHI (FBCM)

CVEUHI (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 100
PtRes: FF DEVICE
Range: Real

PID: OUT_SCALE.EU100
Control Variable Engineering Units HighOP High Range in
Engineering Units.

CVEULO
Type:
Real
Lock:
Engr
Default: 0.0 (GPM,
PPH, etc.)
PtRes: HPM
Range: < CVEUHI

Calculated Value's Low Limit in Engineering Units

Helpful Hint: Same as above for CVEUHI.

CVEULO (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: Real

PID: OUT_SCALE.EU0
Control Variable Engineering Units LowOP Low Range in
Engineering Units.

CYCLEOPT (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

E:$CYCLOPT
Ramp/Soak Cycle OptionDefines whether the ramp/soak cycle stops
after a single cycle, or is continuous. For detailed information, refer to the
Oper
HPM Control Functions and Algorithms manual.
Cyclic
HPM
0-Single (Stop after completing one complete cycle)
1-Cyclic (Repeat complete cycles over and over)
Helpful Hint: If Cyclic is entered, repeats complete ramp/soak cycles after Mode is changed from Man
to Auto. If Single is entered, performs one ramp/soak cycle and then stops.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

121

CYCLETIM

CYCLETIM
Type:
Lock:
Default:
PtRes:
Range:

122

Real
PosProp Output Cycle Time in SecondsDetermines the rate at which raise
or lower output pulses are going to be generated. PV - SP determines the width
Supr
of the output pulse.
10.0 seconds
HPM
0.25 to 1000.0 seconds

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

D (Summer, VdtLdLag)

-DD (Summer, VdtLdLag)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
N/A

Overall BiasDefines the overall bias used in calculating PVCALC.

D1 (VdtLdLag)
Type:
Lock:
Default:
PtRes:
Range:

Real
Fixed Deadtime in MinutesBias value for the variable time delay.
Supr
0.0 minutes
HPM
0.0 to 400.0 minutes

D1, D2 (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Digital Input 1 Status and Digital Input 2 StatusSeparately indicates
whether input 1 and input 2 are on or off.
View
Off
HPM
Off (No input present)
On (Input is present)

D1_0 (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$PVSTATS
Digital Input 1 Equal to A PV State of 0Defines the PV state that
corresponds to input D1 = Off. D1_0 = true only if INPTDIR = Direct and the
View
field contact feeding D1 is open, or INPTDIR = Reverse and contact is
PVState0
cleared.
HPM
0-PVState0 (STATETXT(0) describes D1 = 0)
1-PVState1 (STATETXT(1) describes D1 = 0)
Helpful Hint: Applies only if NODINPTS = 1. D1_0 is always the opposite state of D1_1.

HPM Parameter Reference Dictionary


Honeywell Inc.

123

D1_1 (DigComp, DevCtl)

D1_1 (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

E:$PVSTATS
Digital Input 1 Equals A PV State of 1D1_1 defines the PV state that
corresponds to D1 (Input 1 status) = On. D1_1 = true only if INPTDIR =
Eng/PB
Direct and the field contact feeding D1 is closed, or INPDIR = Reverse and
PVState1
contact is open.
HPM
0-PVState0 (STATETXT(0) describes D1 = 1)
1-PVState1 (STATETXT(1) describes D1 = 1)
Helpful Hint: D1_1, Digital Input 1 Equal To A PV State Of 1, applies only if NODINPTS =
1. D1_1 is always the opposite state of D1_0 and vice versa.

D2 (VdtLdLag)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
> 0.0

Bias for Input P2

D2D1_00 (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

E:$PVSTATS
D2_D1 Zero_Zero PV StateDefines the PV state descriptor that is to be
used and displayed when inputs D2 and D1 are both Off (00).
Eng/PB
MovPV
HPM
0-PVState0 (STATETXT(0) descriptor)
1-PVState1 (STATETXT(1) descriptor)
2-BadPV (BADPVTXT descriptor)
3-MovPV (MOVPVTXT descriptor)
4-PVState2 (STATETXT(2) descriptor)
Helpful Hint: D2D1_00 configuration requires NODINPTS = 2. Option PVState2 cannot be selected
unless NOSTATES = 3. STATETXT(02) is configured for each
DigComp or DevCtl point;
BADPVTXT and MOVPVTXT are configured
during Box Data Point configuration for all DigComp
or DevCtl points in this box.

124

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

D2D1_01 (DigComp, DevCtl)

D2D1_01 (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

E:$PVSTATS
D2D1 Zero_One PV StateDefines the PV state descriptor that is to be used
and displayed when input D2 is Off and input D1 is On (01).
Eng/PB
PVState1
HPM
0-PVState0 (STATETXT(0) descriptor)
1-PVState1 (STATETXT(1) descriptor)
2-BadPV (BADPVTXT descriptor)
3-MovPV (MOVPVTXT descriptor)
4-PVState2 (STATETXT(2) descriptor)
Helpful Hint: D2D1_01 configuration requires NODINPTS = 2. Option PVState2 cannot be
specified unless NOSTATES =3. STATETXT(02) is configured for each
DigComp or DevCtl tag name; BADPVTXT and MOVPVTXT are configured
Box Data Point configuration for all DigComp or DevCtl points in the
box.

during

D2D1_10 (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

E:$PVSTATS
D2D1 One_Zero PV StateDefines the PV state descriptor that is to be used
and displayed when input D2 is On and input D1 is Off (10).
Eng/PB
PVState0
HPM
0-PVState0 (STATETXT(0) descriptor)
1-PVState1 (STATETXT(1) descriptor)
2-BadPV (BADPVTXT descriptor)
3-MovPV (MOVPVTXT descriptor)
4-PVState2 (STATETXT(2) descriptor)
Helpful Hint: D2D1_10 configuration requires NODINPTS = 2. Option PVState2 cannot be
specified unless NOSTATES = 3. STATETXT(02) is configured for each
DigComp or DevCtl point; BADPVTXT and MOVPVTXT are configured
Box Data Point configuration for all DigComp or DevCtl points in the
box.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

during

125

D2D1_11 (DigComp, DevCtl)

D2D1_11 (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

E:$PVSTATS
D2D1 One_One PV StateDefines the PV state descriptor that is to be used
and displayed when inputs D2 and D1 are both On (11).
Eng/PB
BadPV
HPM
0-PVState0 (STATETXT(0) descriptor)
1-PVState1 (STATETXT(1) descriptor)
2-BadPV (BADPVTXT descriptor)
3-MovPV (MOVPVTXT descriptor)
4-PVState2 (STATETXT(2) descriptor)
Helpful Hint: D2D1_11 configuration requires NODINPTS = 2. Option PVState2 cannot be
specified unless NOSTATES = 3. STATETXT(02) is configured for each
DigComp or DevCtl point; BADPVTXT and MOVPVTXT are configured
during Box Data Point configuration for all DigComp or DevCtl points in the
box.

DAMPING (STI)
Type:
Lock:
Default:
PtRes:

Real
Supr/View
0.0
HPM

DampingDefines the first-order PV filtering option for the smart transmitter.


User can also implement PV filtering by using this parameter or the TF
parameter; however, DAMPING is the preferred parameter. If DAMPING has
been configured at the transmitter using the Universal Station, the STI IOP
adjusts the entered value to one of the values in the range shown below for the
appropriate transmitter type. For Multivariable transmitters with SENSRTYP =
SFM the IOP will not adjust the damping value.
Any real number in the range of damping specified by the transmitter user
manual can be used. It can be changed only when the STI point execution state
PTEXECST is Inactive.

Range:
Transmitter Type
Spt
Stt
Sfm
0.0
0.0
0.0
0.16
0.30
0.5
0.32
0.70
1.0
0.48
1.5
2.0
1.00
3.10
3.0
2.0
6.3
4.0
4.0
12.7
5.0
8.00
25.5
10.0
16.0
51.1
50.0
32.0
102.3 100
NaN
NaN
NaN

126

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DATE (HPM Box)

DATE (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Time
View
N/A
HPM
N/A

Current Date/TimeValue of the LCN date in the HPM.

DAY (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
1 to 31

Current DayValue of the LCN date in the HPM.

DB_VALID(1)(40) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$DBVALID Database ValidIndicates if the database is valid. The IOP cannot be set to
RUN unless the database is valid.
Engr
Invalid
HPM
Valid (Database is valid)
Invalid (Database is not valid)

DCFAILFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: OFF
PtRes: IOP
Range: 0 OFF
1 ON

FAIL
Device Control Fail Alarm Flag This parameter indicates that
device control has failed.

DEADBAND(1)(24) (Logic)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
> 0.0

Deadband ValueDefines the value of the deadband for the specified logic
block within the logic slot.

Helpful Hint: DEADBAND requires LOGALGID = EQ, NE, GT, GE, LT, or LE.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

127

DEADBAND (PosProp, PIDPosPr)

DEADBAND (PosProp, PIDPosPr)


Type:
Lock:
Default:
PtRes:
Range:

Deadband in Percent of Full ScaleDefines the error deadband.


Real
Supr
5.0 %
HPM
0.0 to 100.0 %

DEADTIME (PosProp, PIDPosPr)


Type:
Lock:
Default:
PtRes:
Range:

Deadtime (in seconds)Additional pulse time required to overcome the friction


in the motor when it begins to move or change direction. It is added to the
calculated pulse time except when the pulse that was issued in the last cycle time
was in the same direction (as the pulse this time), and the pulse width was equal
to CYCLETIM.
0.0 to 60.0 seconds
Real
Supr
0.0
HPM

DEBOUNCE (DigIn)
Contact Debounce Time in MillisecondsThe length of time an input must
Type:
Integer
remain in a new state for it to be declared as a valid event by the DISOE IOP.
Lock:
Engr/PB
Refer to the Absolute Delay Across parameter located in the Digital Input
Default: 10
Processor table of the HPM Specification and Technical Data.
milliseconds
PtRes: HPM
Range: 0 to 50 milliseconds

DECONF (STI)
Type:
Lock:
Default:
PtRes:
Range:

128

Digitally Enhanced Configuration ModeDefines the contents of the data that


will be sent by the smart transmitter to the STI point.
The use of Pv_Db and Pv_Sv_Db is recommended because they offer database
mismatch detection and on-process mismatch recovery.
This parameter can be changed only when the STI point execution state
PTEXECST is Inactive.
0-Analog (Not Supported)
1-Pv (Transmits only the PV; 4-byte format)
2-Pv_Sv (Transmits the PV and the secondary variable (SV); 4-byte format)
3-PV_Db (Transmits the PV and the transmitter database; 6-byte format)
4-Pv_Sv_Db (Transmits the PV, SV, and the transmitter database; 6-byte format)
Helpful Hint: For the PV_Db and Pv_Sv_Db selections, one byte of the transmitter database
is transmitted each time the PV is transmitted to the STI IOP.
E:$DECONF
Eng/View
Pv_Sv_Db
HPM

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DEFADDR(1-14) (SECM)

DEFADDR(1-14) (SECM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: IOP
Range: 0x10 0xFB

Related to System Management Information Block


Link Address of Non-Configured Devices This is an arrayed
parameter. The first four elements are reserved for devices that have
addresses in the default range (F8-FB). The last ten elements are for
the device in the operational range. This parameter is used by diplays.

DEFDEVID(1-14) (SECM)
FF Param. Source:
Type:
String
Lock:
View
Default: Null String
PtRes: IOP
Range: N/A

Related to System Management Information Block


Device Identifier of Non-Configured Devices This is an arrayed parameter.
The first four elements are reserved for devices that have addresses in the default
range (F8-FB). The last ten elements are for the device in the operational range.
This parameter is shown on diplays.

DEFPDTAG(1-14) (SECM)
FF Param. Source:
Type:
String
Lock:
View
Default: Null String
PtRes: IOP
Range: N/A

Related to System Management Information Block


PD_Tag of Non-Configured Devices This is an arrayed parameter. The
first four elements are reserved for devices that have addresses in the default
range (F8-FB). The last ten elements are for the device in the operational range.
This parameter is used by diplays.

DELCV (IncrSum)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A

Delta CV in Engineering UnitsIndicates the calculated change in the CV


output value in engineering units.

DELCV (Pid)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
N/A
HPM
N/A

Delta CV in PercentIndicates the calculated change in the CV output value in


percent.

HPM Parameter Reference Dictionary


Honeywell Inc.

129

DEV (RegCtl)

DEV (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A

DeviationIndicates the deviation (PV - SP) in engineering units.

DEVADDR (Array)
Type:
Lock:
Default:
PtRes:
Range:

Real
PtBld
NaN
HPM
N/A

Serial Link Device AddressIndicates the serial link address of the device
containing data.

DEVADDR (SECM)
FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: SECM: None
PtRes: IOP
Range: 0x14 0xFF

DlmeBasicInfo.ThisNode
Device Address The fieldbus IOPs device address on the link. TPS Builder
will always attempt to make the fieldbus IOP link address the lowest address on
the link.

DEVCLASS (PECM)
FF Param. Source:
Network Management
Type:
E:$DVCLASS Device Functional Class This parameter defines the functional class of the
device.
Lock:
PtBld
Default: Null
PtRes: IOP
Range: 0 Null
1 Basic
2 LNK_MAST
3 - BRIDGE

DEVDTLST (PECM)
FF Param. Source:
Type:
String
Lock:
View
Default: Null String
PtRes: IOP
Range: N/A

130

None
Device Detail Status This parameter contains the device FBAP VFD status
detail string. This parameter contains detailed information for the DEVSTAT
parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DEVHIFL (RegCtl)

DEVHIFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Deviation High Alarm FlagIndicates whether the DEVHITP has been
exceeded.
View
Off
HPM
Off (No DEVHI alarm)
On (DEVHITP has been exceeded)

DEVHIFL (FBCM)
FF Param. Source:
ALARM_SUM.Current
Type:
Logical
Deviation High Alarm Flag Indicates whether the DEVHITP has
been exceeded.
Lock:
View
Default: Off
PtRes: FF DEVICE
Range: 0-OFF (No DEVHI alarm)
1-ON (DEVHITP has been exceeded)

DEVHIPR (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Deviation High Alarm PriorityDefines the priority of the deviation high
alarm.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

DEVHIPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
Engr
Default: Low
PtRes: IOP
Range:

DV_HI_PRI
Deviation High PriorityPriority of the Deviation High alarm. This
value is mapped from the FF alert priority parameter as follows:
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1
Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction, No Alarm

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

131

DEVHITP (FBCM)

DEVHITP (FBCM)
FF Param. Source:
DV_HI_LIM
Type:
Real
Deviation High Alarm Trip Point Defines the upper limit for the
deviation.
Lock:
Supr
Default: +INF
PtRes: IOP
Range: 0 to PV span, +INF

DEVHITP (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
NaN
HPM
> 0.0,
NaN

Deviation High Alarm Trip PointDefines the upper limit for the deviation.

Helpful Hint: Alarm occurs when the PV is higher than SP + DEVHITP.

DEVID (SECM)
FF Param. Source:
Type:
String
Lock:
View
Default: See description
PtRes: IOP
Range:

System Management DEV_ID


Device Identifier This parameter defines the device ID of the IOP
on a given link. The default value is:
48574C0001-HWL-IOPLNK-000000000?
The last character in the default value can be 1, 2, 3, or 4 if the SECM
point that it is associated with is in slot number 120, 121, 122, or 123,
respectively.

N/A

DEVLOFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

132

Logical
Deviation Low Alarm FlagIndicates whether the DEVLOTP has been
exceeded.
View
Off
HPM
Off (DEVLOTP has not been exceeded)
On (DEVLOTP has been exceeded)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DEVLOFL (FBCM)

DEVLOFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: FF DEVICE
Range: 0-OFF, 1-ON

ALARM_SUM.Current
Deviation Low FlagPV Deviation Low Flag

DEVLOPR (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Deviation Low Alarm PriorityDefines the priority of the deviation low
alarm.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

DEVLOPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
Engr
Default: Low
PtRes: IOP
Range:

R610
11/99

DV_LO_PRI
Deviation Low PriorityPriority of the Deviation Low alarm.
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1

Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction, No Alarm

HPM Parameter Reference Dictionary


Honeywell Inc.

133

DEVLOTP (FBCM)

DEVLOTP (FBCM)
FF Param. Source:
DV_LO_LIM
Type:
Real
Deviation Low Alarm Trip PointDefines the lower limit for the
deviation alarm
Lock:
Supr
Default: -INF
PtRes: IOP
Range: -INF, -PV span to 0

DEVLOTP (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Deviation Low Alarm Trip PointDefines the lower limit for the deviation
alarm.
Supr
NaN
HPM
> 0.0,
NaN
Helpful Hint: Alarm occurs when the PV is lower than SP - DEVLOTP.

DEVSTAT (PECM)
FF Param. Source:
None
Type:
E:$DVSTATE Device StatusDevice FBAP VFD (PECM) Status. Device FBAP
VFD Status. This parameter will be used with the VIEW data as a
Lock:
View
parameter set to indicate the quality of the data for the displays. (In the
Default: NULL
case of the FBCM, CL can use this parameter to qualify.
PtRes: IOP
Range: 0-NULL, 1-OK, 2-BAD

DHTIMMAX(1) - (5) (NIM PSDP)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
NIM
N/A

Maximum Time to Complete a Data Handler RequestSpecifies the


maximum time to complete a Data Handler request in msec.

DIAGCMD (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

E: DIAGCMD Diagnostic Command


Oper
N/A
HPM
Helpful Hint: DIAGCMD resets the ProcMod overrun statistics and AVGPU and MAXPU values.

134

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DISCFL (FBCM)

DISCFL (FBCM)
FF Param. Source:
ALARM_SUM.Current
Type:
Logical
Discrete FlagThe parameter indicates whether an OFFNORMAL
alarm is active
Lock:
View
Default: OFF
PtRes: IOP
Range: 0 OFF (Off-Normal alarm is not active)
1 ON (Off-Normal alarm is active)

DISCPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
Engr
Default: NoAction
PtRes: FF Device
Range:

DISC_PRI
Discrete Alarm PriorityPriority of the discrete alarm.
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1

Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction, No Alarm

DISCST (FBCM)
FF Param. Source:
Type:
Integer
Lock:
Supr
Default: 0
PtRes: FF Device
Range: 0-255

DISC_LIM
Alarm State of Discrete Alarm

DISP_SIM (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Simulation Indicator Display Switchsee also SIM_TXT
Prog
On
HPMM
Off (Simulation indicator is not required to be displayed
On (Simulation indicator is required to be displayed

DISPTYPE (SECM, PECM, FBCM)


FF Param. Source:
None
Type:
E:DISPTYPE Display TypeDerived from FBTYPE.
Lock:
Oper
Default: N/A
PtRes: NIM
Range: CMFBCM, CMPECM, CMSECM

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

135

DISRC(1)(2) (DigComp, DevCtl)

DISRC(1)(2) (DigComp, DevCtl)


Type:

Universal
Ent.Prm
Lock:
PtBld
Default: null.null
PtRes: HPM
Range:

Digital Composite and Device Control Input-Connection SourceSpecify


the sources whose values are to be fetched and delivered to Digital Composite
data point inputs D1 and D2. The source can be specified using the
"Tagname.Parameter" format or the hardware reference address format. Refer to
the HPM Control Functions and Algorithms manual for a detailed description.

Use Tagname.Parameter format for tagged points where Tagname can be up to 16 characters and the
permissible character set is as follows:
Alphabetic A-Z (uppercase only)
Numeric 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters, and must be a legitimate parameter name.
Some possible input-connection sources are
a."DigIn slot Tagname.PVFL"
b."DigOut slot Tagname.SO"
c."Logic slot Tagname.SO(nn)" where nn = 124
d."Logic slot Tagname.Fl(nn)" where nn = 112
e."ProcMod slot Tagname.Fl(nnn)" where nnn = 1127
f."Box Flag slot Tagname.PVFL
g."!Box.FL(nnnn)" for a box flag that resides in the same box;
nnnn = 116,384
h."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the NIM UCN address, xx is the HPM box number, and
nnnn = 14095
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DI (Digital Input)
mm is the IOP Card number (140)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up-to-eight characters and must be a legitimate parameter name.

DITYPE
Type:
Lock:
Default:
PtRes:
Range:

136

E:$DITYPE
Digital Input TypeDefines the type of digital input point.
PtBld
Status
HPM
0-Status (Point is to be used for alarming and event reporting)
1-Latched (Point is to be used for event reporting)
2-Accum (Point is to be used for accumulating pulses)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DLYTIME (DigIn)

DLYTIME (DigIn)
Type:
Lock:
Default:
PtRes:

Integer
Supr
5 seconds
HPM

Delay TimeFor an off-normal alarm, defines the time (in seconds) that a point
with a previously detected alarm condition is guaranteed to remain in alarm,
even if the condition clears. If an alarm condition exists when the delay timer
expires, the point is held in alarm.
For a change of state (COS) alarm, if the PV is in the same state when the delay
timer expires, future state changes are immediately alarmed. If the PV is in the
opposite state, a second COS alarm is produced and the delay timer is restarted.

Range:

0 to 60 seconds

DLYTIME(1)(24) (Logic)
Type:
Lock:
Default:
PtRes:
Range:

Real
Alarm Delay in Seconds for Logic Block
Supr
1 second
HPM
18000 seconds
Helpful Hint: DLYTIME requires LOGALGID = Pulse, MinPulse, MaxPulse, OnDelay, OffDelay, or
Watchdog

DMNODIDX(1-2) (SECM)
FF Param. Source:
Type:
Real
Lock:
View
Default: 0
PtRes: IOP
Range:

R610
11/99

Network Management Information Block


Domain Object Dictionary IndicesThis arrayed parameter defines
the object dictionary indices of the first and second domain objects used
for the link schedule. The IOP reads the value of this arrayed parameter
from the stack when the IOP is started up.

0 - 65535

HPM Parameter Reference Dictionary


Honeywell Inc.

137

DODSTN(1)(3) (DigComp, DevCtl)

DODSTN(1)(3) (DigComp, DevCtl)


Type:

Universal
Digital Composite and Device Control Output-Connection Destination
Specifies up to three output connection destinations that are to receive the OP
Ent.Prm
output from this point. The destination can be specified using the
Lock:
PtBld
"Tagname.Parameter" format or the hardware reference address format. Refer to
Default: null.null
the HPM Control Functions and Algorithms manual for a detailed description.
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters and the permissible
character set is as follows:
Alphabetic A-Z (uppercase only)
Numeric 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters, and must be a legitimate parameter name.
Some possible output-connection destinations are
a."DigOut slot tagname.ONPULSE or OFFPULSE"
b."DigOut slot Tagname.SO"
c."Logic slot Tagname.Fl(nn)" where nn = 712
d."ProcMod Tagname.Fl(nnn)" where nnn = 1127
e."Flag slot Tagname.PVFL
f."!Box.FL(nnnn)" for a box flag that resides in the same HPM box; nnnn = 116,384.
g."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the NIM UCN address, xx is the HPM box number, and nnnn = 14095.
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DO (Digital Output)
mm is the IOP Card number (140)
The letter "S" is a constant.
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

DOTYPE (DigOut)
Type:
Lock:
Default:
PtRes:
Range:

E:$DOTYPE
Digital Output TypeDetermines the type of digital output point.
PtBld
Status
HPM
0-Status (Status output type)
1-Pwm (Pulse Width Modulated output type)

DSA
Type:
Lock:
Default:
PtRes:
Range:

138

Integer
Device Soft AddressThe logical address of an IOP: 1-40 for primary
IOPs and 129 - 168 for secondary IOPs.
View
N/A
HPM
1 - 40 for primary IOPs
129 - 168 for secondary IOPs

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

EIPPCODE

-EEIPPCODE
Type:
Lock:
Default:
PtRes:
Range:

Ent_Id
Event-Initiated Processing Point IdentifierDefines the tag name of the point
in the AM or CM that is to be notified when an event is detected by this point.
Engr
Null
NIM
Tag name of the data point can be up to 16 characters and the permissible character set is as follows:
Alphabetic A-Z (uppercase only)
Numeric 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive underscores are
not allowed.
Embedded space characters are not allowed.
Helpful Hint: EIPPCODE configuration requires PNTTYPE = DigIn, DigComp, Logic, Flag or
DevCtl and EVTOPT = Eip or Eip_Soe. For HPM Box Flag points, this
parameter applies only to
slots 1 through 128.

EQUOBJNM
Type:
Lock:
Default:
PtRes:
Range:

String
View
Blank
HPM
N/A

Equipment List Object NameSpecifies the Equipment List Object Name


(CL object header)

ERRCODE (Array)
Type:
Lock:
Default:
PtRes:

String_8
View
Spaces
HPM

Serial Interface/Serial Link Communication Error CodeWhen the


BADPVFL parameter = ON, this parameter provides additional information if
initialized by the serial interface FTA driver program.
SI Array Point Error Code Values
HPM
HPM IdleWhen the HPMM status is IDLE, Array point configuration may or
may not be loaded to the SI IOP.
Iop CommWhen the HPMM status is RUN, Array point configuration is NOT
loaded to the SI IOP.
SI IOP
No_FTAAppears when the power adapter panel is not connected to the IOP.
FTA_CommAppears when the corresponding FTA is not connected to the
power adapter panel, or when communication between the IOP and FTA has
failed.
CFG_LoadAppears when configuration data is downloaded to the FTA.
Mod_IdleAppears when configuration data is downloaded to the FTA and the

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

139

ESWAUTO (RegCtl)

IOP is in IDLE mode, or when the IOP operating state is switched from RUN to
IDLE.
SI IOP FTA Common
Dev AddrThe device address has a configuration error
Data TypeThe data type has a configuration error
StartidxThe start index has a configuration error
# ElemntA number of elements configuration error has occurred
ConfigAn application-specific configuration error has occurred
Inv RespAn invalid field device response has occurred
Parity, Checksum, MsgTmout, ChrTmoutA field device communication
error has occurred
Ex or xxAn exception or other field device error has occurred. The xx error
code is specific to the field device
Fac TestA factory test is in progress
OKNo errors exist
Range:

N/A

ESWAUTO (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

External Switching Flag for Automatic ModeWhen On, means that this
point's operating mode has been switched from some mode other than automatic
to the automatic mode by an external source.

ESWCAS (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

Eternal Switching Flag for Cascade ModeWhen On, means that this point's
operating mode has been switched from some mode other than cascade to
cascade mode, by an external source.

ESWENBST (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ENBLSTAT External Mode Switching Enable StateDefines whether external mode


switching is permitted for this point.
Oper
Disable
HPM
0-Disable (Does not allow external switching of point's mode)
1-Enable (Allows external switching of point's mode)
Helpful Hint: ESWENBST cannot be changed if parameter SHUTDOWN is On or if
parameter REDTAG is On.

140

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

ESWMAN (RegCtl)

ESWMAN (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

External Switching Flag for Manual ModeWhen On, means that this point's
operating mode has been switched from some mode other than the manual mode
to the manual mode by an external source.

EUDESC
Type:
Lock:
Default:
PtRes:

String_8
PtBld
Blank
NIM

Range:

Permissible character set consists of all characters on the Engineer' s Keyboard. Basically this set consists
of alphabetics A-Z, numerics 0-9, and the following special characters: space ! % & ' ( ) * + - / : ;
> < = ? _ , . $

Engineering Units DescriptorAn eight-character descriptor that defines the


name of the engineering units (EU) that are displayed on the Group and Detail
Displays for this point as shown in Figure N-1 (see NAME). In this figure,
LBS/SEC is the engineering unit descriptor.

EUDESC (FBCM)
FF Param. Source:
None
Type:
String
Engineering Unit DescriptorAn descriptor that defines the name of
the engineering units (EU) that are displayed on the Group and Detail
Lock:
PtBld
Displays for this point as shown in Figure N-1 (see NAME). In this
Default: Blank
figure, LBS/SEC is the engineering unit descriptor.
PtRes: NIM
Range: Permissible character set consists of all characters on the Engineer' s Keyboard. Basically this set
consists of alphabetics A-Z, numerics 0-9, and the following special characters: space ! % & '
( ) * + - / : ; > < = ? _ , . $

EUNDESC (1)(168)
Type:
Lock:
Default:
PtRes:

String_72
View
Blanks
HPM

Range:

nn = 1-40 specifies one of the 40 acting primaries.


nn = 129-168 specifies one of the 40 acting secondaries.

R610
11/99

IOP Generic DescriptorUsed as additional display text to help the operator


diagnose potential problems with the IOP. It is primarily used with diagnostic
displays.

HPM Parameter Reference Dictionary


Honeywell Inc.

141

EVRCINPG

EVRCINPG
Type:
Lock:
Default:
PtRes:
Range:

Logical
View

NIM Event Recovery in Progress Flag

HPM
Off
On

EVTOPT (DigComp)
Type:
Lock:
Default:
PtRes:
Range:

E:$EVTOPT Event Reporting OptionIf EVTOPT = Eip and the PV changes or a PV


alarm is generated, the AM or CM data point named EIPPCODE is notified and
PtBld
a "process special" on that data point takes place.
None
HPM
0-None (Event-Initiated Processing is not allowed)
1-Eip (Process special is triggered in AM/CM)
Helpful Hint: EVTOPT configuration requires NODINPTS > 0.

EVTOPT (DevCtl, DigIn)


Type:
Lock:
Default:
PtRes:

E:$EVTOPT
PtBld
None
HPM

Range:

0-None (Neither Eip nor Soe is allowed)


1-Eip (Process special is triggered in AM/CM)
2-Eip_Soe (Eip and Soe are both allowed)
3-Soe (Point notifies Sequence of Events Processing)

Event Reporting OptionIf EVTOPT = Eip and the PV changes, the AM or


CM data point named EIPPCODE is notified and a "process special" on that
data takes place. If EVTOPT = Soe and a PV change occurs, Sequence Of
Events Processing is notified. If EVTOPT = EipSoe, the actions in both apply.

Helpful Hint: EVTOPT configuration requires DITYPE = Status or Latched. If DITYPE =


Latched, EVTOPT cannot = EIPSOE or SOE.

142

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

EXTDATA (Array)

EXTDATA (Array)
Type:
E:$EXTDAT
A
Lock:
Default:
PtRes:
Range:

External Data OptionIndicates if either the Array point flags, numerics, or


strings are mapped from a serial interface.

PtBld
None
HPM
None (None of the flags, numerics, or strings are mapped from a serial interface)
IO_FL (IO flags are mapped from a serial interface)
IO_NN (IO numerics are mapped from a serial interface)
IO_STR (IO strings are mapped from a serial interface)
UCN_FL (Reserved for future use)
UCN_NN (Reserved for future use)
UCN_STR (Reserved for future use)
Helpful Hint: You can map either flags, numerics, or strings from the Serial
Interface to a single Array point.

EXTSWOPT
Type:
Lock:
Default:
PtRes:

E:EXTSWOPT
Eng/PB
None
HPM

Range:

0-None (No external mode switching is allowed)


1-Ems (External source can change point's mode)
2-Emp (Not implemented)

R610
11/99

External Mode Switching OptionExternal mode switching is typically


used to establish mode interlocks, or under certain process conditions, to
restrict the use of a mode that invokes a higher level of control. Refer to the
HPM Control Functions and Algorithms manual for a detailed description of
external mode switching.

HPM Parameter Reference Dictionary


Honeywell Inc.

143

F (FlowComp)

-F-

F (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Flow InputIndicates the value of the uncompensated flow input. This input is
a square-rooted, differential pressure input.

FAILCODE
Type:
Lock:
Default:
PtRes:
Range:

E:$IOMHF
View
I/O Processor Hard Fail Status
N/A
IOP
0-Unknown (Unknown status)
1-PowerDwn(This IOP Powered Down)
2-InvPrgEx(Invalid Program Execution)
3-EpromErr(EPROM Checksum Error)
4-RamCntEr(RAM Contents Error)
5-RamAdrEr(RAM Addressing Error)
6-DpaError(Device Physical Address Error)
7-DsaError(Device Soft Address Error)
8-RxBufOfl(I/O Link Receive Buffer Overflow)
9-IOLJaber(I/O Link Jaber Circuit Failure)
1011-BadPgJmp(Illegal Value of Case Control)
12-AdCIncmp(A to D Conversion Incomplete)
13-AdOutOvf(A to D Output Value Overflow)
14-AdOutUdf(A to D Output is less than Zero)
15-AdCCalEr(A to D Calibration is incorrect)
16-BadDcLtc(Bad DC LTC)
17-Dmt_Tmot(Dead Man Timer Timeout)
18-MLtOutFl(Multiple Output Failure)
20-BadDaRng(Bad D to A Range)
21-MstrTmot(Master 68K Timeout)

FAILOPT(1)(168) (IOP)
Type:
Lock:
Default:
PtRes:
Range:

144

E:FAILOPT Failure Option for OutputsDefines the state which an AO or DO IOP goes
into if the IOP itself, or the HPMM fails. If the IOP failure is due to power loss,
Eng/PB
outputs go to unpowered regardless of the FAILOPT value. When power is
Unpower
restored to the module, outputs are reset regardless of the FAILOPT values.
HPM
0-Hold (Hold output at last good value)
1-Unpower (Remove power from the output)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FBSCHOBJ(1-20) (SECM)

FBSCHOBJ(1-20) (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: N/A

SMIB: FB Start Entry Object


Function Block Schedule Data Objects 1-20This is an arrayed
parameter.

FBSCHVER (SECM)
FF Param. Source:
Type:
Real
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 0 - 65535

SMIB: Version of Schedule


Function Block Schedule Version Number

FBTIME (DevCtl, DigComp)


Type:
Lock:

Integer
Feedback TimeSets the amount of time (in seconds) that the point should
wait before generating a "command disagree" alarm after the operator has
Supr if
issued a start/stop-type command to a field device.
CMDFALTM
is changed from
a non-zero value
to a zero value,
else Eng/PB
Default: 0
PtRes: HPM
Range: 0 to 1000 seconds (0 indicates that command disagree alarming is disabled)
Helpful Hint: FBTIME can be increased to compensate for a slow-responding field device
that does not respond to the operators command in time to prevent a
command-disagree alarm.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

145

FBTYPE (FBCM)

FBTYPE (FBCM)
FF Param. Source:
None
Type:
E:$FBALGO Function Block TypeDefines the type of function block.
Lock:
PtBld
Default: NULL
PtRes: IOP
Range: 0-NULL (No Function)
1-AI (Analog Input)
2-ANLGALM (Analog Alarms)
3-ANLGHUM (Analog Human Interface)
4-AO (Analog Output)
5-ARITHMET (Arithmetic)
6-BIASGAIN (Bias/Gain)
7-CALCANLG (Calculate Analog)
8-CALCDISC (Calculate Discrete)
9-CHARCTZR (Signal Characterizer)
10-CMPLXAO (Complex Analog Output)
11-CMPLXDO (Complex Discrete Output)
12-CTRLSEL (Control Selector)
13-DEADTIME (Deadtime)
14-DEVCTRL (Device Control)
15-DI (Discrete Input)
16-DISCALM (Discrete Alarm)
17-DISCHUM (Discrete Human Interface)
18-DO (Discrete Output)
19-INTEGRAT (Integrator)
20-LEADLAG (Lead Lag)
21-MANLOAD (Manual Loader)
22-PD (PD Control)
23-PID (PID Control)
24-PULSEIN (Pulse Input)
25-RATIO (Ratio)
26-SNGLSEL (Signal Selector)
27-SPRAMP (Setpoint Ramp Generator)
28-SPLITTER (Splitter)
29-STEPCTRL (Step Control)
30-TIMER (Timer)
31-AICALC (Analog Input Calculator)
32-AOCTL (Analog Output Control)
33-DICALC (Discrete Input Calculator)
34-DOCTL (Digital Output Control)

FF (PidFf)
Type:
Lock:
Default:
PtRes:
Range:

146

Real
View
N/A
HPM
N/A

Feed Forward Algorithm InputFF is the feedforward input signal value that
is added to (FFOPT = Add) or multiplied by (FFOPT = Multiply) the PidFf
algorithm's incremental output, before the full-value output is accumulated. FF
is normally a parameter with a percentage value.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFALMCUR (FBCM)

FFALMCUR (FBCM)
FF Param. Source:
ALARM_SUM.Current
Type:
Integer
Foundation Fieldbus Alarms Current TypeCurrent alert status of
the alarms associated with the function block.
Lock:
View
Default: O
PtRes: FFDevice
Range: 0-Discrete alarm (LSB) The zero state is used to indicate alarm clear, acknowledged, reported,
enabled.
1-High high alarm
2-High alarm
3-Low low alarm
4-Low alarm
5-Deviation high alarm
6-Deviation low alarm
7-Block Alarm
8-15-Defined by lock profile

FFBCINST (FBCM)
FF Param. Source:
BKCAL_IN.Status
Type:
E:$FBSTATS Foundation Fieldbus Block Initialize StatusThe status from a
lower block's BKCAL_OUT that is used to prevent reset windup and to
Lock:
View
initialize the control loop.
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFBCINVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

BKCAL_IN.Value
Foundation Fieldbus Block Initialize ValueThe value from a lower
block's BKCAL_OUT that is used to prevent reset windup and to
initialize the control loop.

FFBCOPST (FBCM)
FF Param. Source:
BKCAL_OUT.Status
Type:
E:$FBSTATS Foundation Fieldbus Calculated Block Output StatusThe status
required by an upper block's BKCAL_IN.
Lock:
View
Default: Bad
PtRes:
FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

147

FFBCOPVL (FBCM)

FFBCOPVL (FBCM)
FF Param. Source:
BKCAL_OUT.Value
Type:
Real
Foundation Fieldbus Block Calculated OutputValueThe value
required by an upper block's BKCAL_IN.
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFCSIDST (FBCM)
FF Param. Source:
CAS_IN_D.Status
Type:
E:$FBSTATS Foundation Fieldbus Cascade Input StatusStatus of Remote
Setpoint of Discrete Block
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFCSIDVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: Off
PtRes: FF DEVICE
Range: 0-OFF
1-ON

CAS_IN_D.Value
Foundation Fieldbus Cascade Input ValueRemote setpoint value
of a discrete block, which must come from another FF block or the
HPM through an output connection.

FFCSINST (FBCM)
FF Param. Source:
CAS_IN.Status
Type:
E:$FBSTATS Foundation Fieldbus Cascade Input StatusStatus of the remote
setpoint value that comes from another FF block or from the HPM
Lock:
View
through an output connection.
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

148

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFCSINVL (FBCM)

FFCSINVL (FBCM)
FF Param. Source:
CAS_IN.Value
Type:
Real
Foundation Fieldbus Cascade Input ValueInput value that comes
from another FF block or from the HPM through an output connection.
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFDEVREV (SECM, PECM)


FF Param. Source:
VFD revision number
Type:
String
Foundation Fieldbus Device RevisionThe revision number of
the fieldbus device. For a SECM, it is the IOP device revision
Lock:
PtBld
number (which is not in checkpoint). For a PECM, it is the FBAP
Default: SECM = "REV
VFD information (which is in the checkpoint). Used for FBAP
0.00"
matching and display.
PECM = Null
String
PtRes: IOP
Range: N/A

FFDVHILM (FBCM)
FF Param. Source:
DV_HI_LIM
Type:
Real
Foundation Fieldbus Deviation High Alarm LimitThe value of the
high deviation alarm limit in engineering units.
Lock:
Supr
Default: +INF
PtRes: FF DEVICE
Range: 0 to PV Span, +INF

FFDVHIPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range:

R610
11/99

DV_HI_PRI
Foundation Fieldbus Deviation High Priority The priority of the
high deviation alarm.
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1
Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction

HPM Parameter Reference Dictionary


Honeywell Inc.

149

FFDVLOLM (FBCM)

FFDVLOLM (FBCM)
FF Param. Source:
DV_LO_LIM
Type:
Real
Foundation Fieldbus Deviation Low AlarmThe value of the low
deviation alarm limit in engineering units.
Lock:
Supr
Default: -INF
PtRes: FF DEVICE
Range: -INF, -PV Span to zero

FFDVLOPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range:

DV_LO_PRI
Foundation Fieldbus Deviation Low Alarm PriorityThe priority of
the low deviation alarm.
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1
Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction

FFERRMSG (SECM, PECM)


FF Param. Source:
Type:
String
Lock:
View
Default: Null String
PtRes: IOP
Range: N/A

None
Foundation Fieldbus Error MessageA string that describes the last
error encountered on the SECM or PECM. The error may be stack
related; the message is mainly for diagnotic/debug purposes.

FFFFDECP (FBCM)
FF Param. Source:
Type:
Integer
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 0-255

FF_SCALE.DecPt
Foundation Fieldbus Feed-Forward Decimal PointThe number of
digits to the right of the decimal point which is used in displaying the
specific parameter.

FFFFGAIN (FBCM)
FF Param. Source:
Type:
Real
Lock:
Supr
Default: 0
PtRes: FF DEVICE
Range: Floating Point

150

FF_GAIN
Foundation Fieldbus Feed-Forward GainThe gain that the feed
forward input is multiplied by before it is added to the calculated
output.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFFFS0 (FBCM)

FFFFS0 (FBCM)
FF Param. Source:
FF_SCALE.EU0
Type:
Real
Foundation Fieldbus Feed-Forward Scale ZeroThe feed forward
input low scale value.
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 32 BIT FLOAT

FFFFS100 (FBCM)
FF Param. Source:
FF_SCALE.EU100
Type:
Real
Foundation Fieldbus Feed-Forward Scale 100The feed forward
input high scale value.
Lock:
Engr
Default: 100
PtRes: FF DEVICE
Range: 32 BIT FLOAT

FFFFUIDX (FBCM)
FF Param. Source:
FF_SCALE.UnitIndex
Type:
E:$FFEUIDX Foundation Fieldbus Feed-Forward Unit IndexThe feed forward
input engineering units code.
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: Refer to the Appendix

FFFFVLST (FBCM)
FF Param. Source:
FF_VAL.Status
Type:
E:$FBSTATS Foundation Fieldbus Feed-Forward Value StatusThe status of the
feed-forward value.
Lock:
View
Default: Bad_OOS
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFFFVLVL (FBCM)
FF Param. Source:
FF_VAL.Value
Type:
Real
Foundation Fieldbus Feed Forward ValueThe feed forward value.
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

151

FFGAIN (FBCM)

FFGAIN (FBCM)
FF Param. Source:
GAIN
Type:
Real
Foundation Fieldbus GainThe gain that the feed-forward input is
multiplied by before it is added to the calculated control output.
Lock:
Supr
Default: 0
PtRes: FF DEVICE
Range: Floating Point

FFHHLM (FBCM)
FF Param. Source:
HI_HI_LIM
Type:
Real
Foundation Fieldbus High High AlarmThe value of the high high
alarm limit in engineering units.
Lock:
Supr
Default: +INF
PtRes: FF DEVICE
Range: PV_SCALE, +INF

FFHHPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range:

HI_HI_PRI
Foundation Fieldbus High High PriorityPriority of the high high
alarm.
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1
Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction

FFHILM (FBCM)
FF Param. Source:
HI_LIM
Type:
Real
Foundation Fieldbus High AlarmThe value of the high alarm limit
in engineering units.
Lock:
Supr
Default: +INF
PtRes: FF DEVICE
Range: PV_SCALE, +INF

FFHIPR (FBCM)
FF Param. Source:
HI_PRI
Type:
E:ALPRIOR Foundation Fieldbus High PriorityPriority of the high alarm.
This value is mapped from the FF alert priority parameter as follows:
Lock:
Engr
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
Default: 0
PtRes: FF DEVICE JnlPrint <- 3; Journal <- 2; NoAction <- 1
Range: Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction

152

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFINSTS (FBCM)

FFINSTS (FBCM)
FF Param. Source:
IN.Status
Type:
E:$FBSTATS Foundation Fieldbus Input StatusStatus of the primary input value,
required for the blocks that filter input to get PV.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFINVAL (FBCM)
FF Param. Source:
IN.Value
Type:
Real
Foundation Fieldbus Input ValueThe primary input value of the
block, required for blocks that filter the input to get the PV.
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFLLLM (FBCM)
FF Param. Source:
LO_LO_LIM
Type:
Real
Foundation Fieldbus Low Low AlarmThe value of the low low
alarm limit in engineering units.
Lock:
Supr
Default: -INF
PtRes: FF DEVICE
Range: -INF, PV_SCALE

FFLLPR (FBCM)
FF Param. Source:
LO_LO_PRI
Type:
E:ALPRIOR Foundation Fieldbus Low Low PriorityThe priority of the low low alarm.
This value is mapped from the FF alert priority parameter as follows: Emergency
Lock:
Engr
<- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4; JnlPrint <- 3; Journal <- 2;
Default: 0
NoAction <- 1
PtRes: FF Device
Range: Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction

FFLOLM (FBCM)
FF Param. Source:
LO_LIM
Type:
Real
Foundation Fieldbus Low AlarmThe value of the low alarm limit
in engineering units.
Lock:
Supr
Default: -INF
PtRes: FF DEVICE
Range: -INF, PV_SCALE

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

153

FFLOPR (FBCM)

FFLOPR (FBCM)
FF Param. Source:
LO_PRI
Type:
E:ALPRIOR Foundation Fieldbus Low PriorityPriority of the low alarm.
This value is mapped from the FF alert priority parameter as follows:
Lock:
Engr
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
Default: 0
PtRes: FF DEVICE JnlPrint <- 3; Journal <- 2; NoAction <- 1
Range: Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction

FFMODEA (PECM, FBCM)


FF Param. Source:
MODE_BLK.Actual
Type:
Integer
Mode ActualDefines the actual mode of the resource or function
block (CM points).
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: 0 to 255
(e.g., OOS=1, IMan=2, LO=4, Man=8, Auto=16, Cas=32, RCas=64, ROut=128)

FFMODEN (PECM, FBCM)


FF Param. Source:
MODE_BLK.Normal
Type:
Integer
Normal Mode Defines the normal mode of the resource or function
block (CM points).
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 0 to 255 (e.g., Man=8, Auto=16, Auto+Cas=48, Auto+RCas=80, Auto+RCas+Cas=112,)

FFMODEP (PECM, FBCM)


FF Param. Source:
Type:
Integer
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 0 to 255

MODE_BLK.Permitted
Mode PermittedDefines the permitted modes of the resource or
function block (CM point).

(e.g., OOS=1, Man=8, OOS+Man=9, Auto=16, OOS+Man+Auto=25,

FFMODET (PECM, FBCM)


FF Param. Source:
MODE_BLK.Target
Type:
Integer
Target ModeDefines the target mode of the resource or function
block. (CM points)
Lock:
Oper
Default: 0
PtRes: FF DEVICE
Range: 0 to 255 (e.g., OOS+Man=9, Man=8, Auto=16, Auto+Cas=48, Auto+RCas=80, )

154

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFOEXPST (FBCM)

FFOEXPST (FBCM)
FF Param. Source:
OUT_EXP.Status
Type:
E:$FBSTATS Foundation Fieldbus Output Expired StatusThe status of the
expired output.
Lock:
View
Default: Bad_OOS
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFOEXPVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range:

OUT_EXP.Value
Foundation Fieldbus Output Expired ValueThis is the time
expired value. Stops when TIMER_SP is reached. Reset to zero by
RESET_IN command, or at the start of next timer event if QUIES_OPT
= LAST, or when the block becomes quiescent if QUIES_OPT =
CLEAR.

Floating Point

FFOPDECP (FBCM)
FF Param. Source:
Type:
Integer
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 0-255

OUT_SCALE.DecPt
Foundation Fieldbus Output Decimal PointThe number of digits to
the right of the decimal point which is used in displaying the OUT value
and other parameters having the same scaling as the OUT value.

FFOPHILM (FBCM)
FF Param. Source:
OUT_HI_LIM
Type:
Real
Foundation Fieldbus Output High LimitThe value of the upper
limit to which the output is limited in all modes other than Manual.
Lock:
Supr
Default: 100
PtRes: FF DEVICE
Range: OUT_SCALE +/- 10%

FFOPLOLM (FBCM)
FF Param. Source:
OUT_LO_LIM
Type:
Real
Foundation Fieldbus Output Low Limit The value of the lower
limit to which the output is limited in all modes other than Manual.
Lock:
Supr
Default: 0
PtRes: FF DEVICE
Range: OUT_SCALE +/- 10%

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

155

FFOPS0 (FBCM)

FFOPS0 (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 32 bit IEEE

OUT_SCALE.EU0
Foundation Fieldbus OUT Parameter Scaling ZeroThe low scale
value of the output and other parameters having same scaling as the
output.

FFOPS100 (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 100
PtRes: FF DEVICE
Range: 32 bit IEEE

OUT_SCALE.EU100
Foundation Fieldbus OUT Parameter Scaling 100The high scale
value of the output and other parameters having same scaling as the
output.

FFOPT (PidFf)
Type:
Lock:
Default:
PtRes:
Range:

E:FFOPT
Feed Forward TypeDetermines whether a PidFf algorithm's feedforward
input signal (FF) is added to or multiplied by the incremental output, before the
Eng/PB
full-value output is accumulated.
Multiply
HPM
0-Add (Scaled Feedforward + Feedback)
1-Multiply (Feedback x Scaled, Biased Feedforward)

FFOPUIDX (FBCM)
FF Param. Source:
Type:
E:$FFEUIDX
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: Unsigned 16

OUT_SCALE.UNITiNDEX
Foundation Fieldbus Out Parameter IndexThe engineering units
code for the output and other parameters having same scaling as the
output.

FFOREMST (FBCM)
FF Param. Source:
OUTPUT REMAINING Status
Type:
E:$FBSTATS Foundation Fieldbus Output Remaining StatusStatus of the
remaining time value (FFOREMVL).
Lock:
View
Default: Bad_OOS
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

156

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFOREMVL (FBCM)

FFOREMVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

OUTPUT REMAINING Value


Foundation Fieldbus Remaining ValueThis is the time remaining if
the timer is active. Stops when event ceases (block becomes quiescent).
Resets to 0.0 if QUES_OPT = CLEAR and the timer is inactive.

FFOUT1ST (FBCM)
FF Param. Source:
OUT_1.Status
Type:
E:$FBSTATS Foundation Fieldbus Output 1 StatusThe status of the first output
(Splitter, Analog Calculate block)
Lock:
View
Default: Bad_OOS
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFOUT1VL (FBCM)
FF Param. Source:
OUT_1.Value
Type:
Real
Foundation Fieldbus Output 1 ValueThe value of the first output
(Splitter, Analog Calculate block)
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFOUT2ST (FBCM)
FF Param. Source:
OUT_2.Status
Type:
E:$FBSTATS Foundation Fieldbus Output 2 StatusThe status of the second
output (Splitter, Analog Calculate block).
Lock:
View
Default: Bad_OOS
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

157

FFOUT2VL (FBCM)

FFOUT2VL (FBCM)
FF Param. Source:
OUT_2.Value
Type:
Real
Foundation Fieldbus Output 2 ValueThe value of the second
output (Splitter, Analog Calculate block).
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFOUTAST (FBCM)
FF Param. Source:
OUT_ACCUM.Status
Type:
E:$FBSTATS Foundation Fieldbus Accumulated-Output Value StatusStatus of
the accumulated output value.
Lock:
View
Default: Bad_OOS
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFOUTAVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

OUT_ACCUM.Value
Foundation Fieldbus Out A ValueThis parameter is an
accumulated count for the Pulse Input Function Block. It is intended to
be connected to an Integrator block for totalization.

FFOUTDST (FBCM)
FF Param. Source:
OUT_D.Status
Type:
E:$FBSTATS Foundation Fieldbus Out Discrete StatusStatus of the primary
discrete value calculated as a result of the executing function.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

158

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFOUTDVL (FBCM)

FFOUTDVL (FBCM)
FF Param. Source:
OUT_D.Value
Type:
Integer
Foundation Fieldbus Out Discrete ValueThe primary discrete
value calculated as a result of the executing function.
Lock:
Oper
Default: 0
PtRes: FF DEVICE
Range: OUT_STATE

FFOUTSTS (FBCM)
FF Param. Source:
OUT.Status
Type:
E:$FBSTATS Foundation Fieldbus Out Discrete Status StatusStatus of the
primary analog value calculated as a result of the executing function.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFOUTVAL (FBCM)
FF Param. Source:
OUT.Value
Type:
Real
Foundation Fieldbus Out ValueThe primary analog value
calculated as a result of the executing function.
Lock:
Oper
Default: NaN
PtRes: FF DEVICE
Range: OUT_SCALE +/- 10 %

FFPTRPST (FBCM)
FF Param. Source:
PTRIP Output Status
Type:
E:$FBSTATS Foundation Fieldbus OUT_PTRIP StatusStatus of the second
discrete output of the integrator block.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

159

FFPTRPVL (FBCM)

FFPTRPVL (FBCM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: 0-OFF, 1-ON

OUT_PTRIP.Value
Foundation Fieldbus OUT_PTRIP ValueThe second discrete
output of the integrator block.

FFPVDECP (FBCM)
FF Param. Source:
Type:
Integer
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: Integer8

PV_SCALE.DecPt
Foundation Fieldbus PV Decimal PointThe number of digits to the
right of the decimal point which is used in displaying the PV and other
parameters having same scaling as PV.

FFPVS0 (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 32 bit IEEE

PV_SCALE.EU0
Foundation Fieldbus PV Scale ZeroThe low scale value of the PV
and other parameters having same scaling as PV.

FFPVS100 (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 100
PtRes: FF DEVICE
Range: 32 bit IEEE

PV_SCALE.EU100
Foundation Fieldbus PV Scale 100The high scale value of the PV
and other parameters having same scaling as PV.

FFPVSTS (FBCM)
FF Param. Source:
PV.Status
Type:
E:$FBSTATS Foundation Fieldbus PV StatusStatus of primary analog value for
use in executing the function. Read only.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: Unsigned8

160

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFPVUIDX (FBCM)

FFPVUIDX (FBCM)
FF Param. Source:
PV_SCALE.UnitIndex
Type:
E:$FFEUIDX Foundation Fieldbus PV IndexThe engineering units code for the
PV and other parameters having same scaling as PV.
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: Unsigned16

FFPVVAL (FBCM)
FF Param. Source:
PV.Value
Type:
Real
Foundation Fieldbus PV ValueThe primary analog value for use in
executing the function block.
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFRATE (FBCM)
FF Param. Source:
RATE
Type:
Real
Foundation Fieldbus RateDefines the derivative time constant, in
seconds.
Lock:
Supr
Default: 0
PtRes: FF DEVICE
Range: Floating Point

FFRBDST (FBCM)
FF Param. Source:
READBACK_D.Status
Type:
E:$FBSTATS Foundation Fieldbus Readback Discrete StateThis indicates the
readback value of the actual discrete valve or other actuator position.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

161

FFRBST (FBCM)

FFRBST (FBCM)
FF Param. Source:
READBACK.Status
Type:
E:$FBSTATS Foundation Fieldbus Readback StatusThis indicates the readback
status of the actual continuous valve or other actuator position.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFRCIDST (FBCM)
FF Param. Source:
Type:
E:$FBSTATS
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: Unsigned8

RCAS_IN_D.Status
Foundation Fieldbus Remote Cascade Status Status of target
setpoint provided by the supervisory host, such as an AM, to discrete
control or to the output block.

FFRCIDVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: Off
PtRes: FF DEVICE
Range: PV Units

RCAS_IN_D.Value
Foundation Fieldbus Remote Cascade Discrete ValueTarget
setpoint value provided by supervisory host, such as an AM, to discrete
control or to the output block.

FFRCINST (FBCM)
FF Param. Source:
Type:
E:$FBSTATS
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: Unsigned8

162

RCAS_IN.Status
Foundation Fieldbus Remote Cascade StatusStatus of the target
setpoint provided by the supervisory host to a analog control or output
block.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFRCINVL (FBCM)

FFRCINVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

RCAS_IN.Value
Foundation Fieldbus Remote Cascade Input ValueThe target
setpoint value provided by the supervisory host to a analog control or
output block.

FFRCOPST (FBCM)
FF Param. Source:
Type:
E:$FBSTATS
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: Unsigned8

RCAS_OUT.Status
Foundation Fieldbus Remote Cascade Output StatusStatus of the
block setpoint after ramping - provided to the supervisory host for back
calculation and to allow action to be taken under limiting conditions or
mode changes.

FFRCOPVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

RCAS_OUT.Value
Foundation Fieldbus Remote Cascade Output ValueValue of the
block setpoint after ramping - provided to the supervisory host for back
calculation and to allow action to be taken under limiting conditions or
mode changes.

FFRESET (FBCM)
FF Param. Source:
Type:
Real
Lock:
Supr
Default: +INF
PtRes: FF DEVICE
Range: Positive

RESET
Foundation Fieldbus ResetThe integral time constant in seconds per
repeat.

FFROINST (FBCM)
FF Param. Source:
Type:
E:$FBSTATS
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: Unsigned8

R610
11/99

ROUT_IN.Status
Foundation Fieldbus Remote ROUT_IN StatusStatus of the target
output provided by a Host to the control block for use as the output
(Rout mode).

HPM Parameter Reference Dictionary


Honeywell Inc.

163

FFROINVL (FBCM)

FFROINVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

ROUT_IN.Value
Foundation Fieldbus Remote ROUT_IN ValueValue of the target
output provided by a Host to the control block for use as the output
(Rout mode).

FFROOPST (FBCM)
FF Param. Source:
Type:
E:$FBSTATS
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: Unsigned8

ROUT_OUT.Status
Foundation Fieldbus Remote ROUT_OUT StatusStatus of the block output
provided by the Host for back calculation in Rout mode and to allow action to be
taken under limited conditions or mode changes.

FFROOPVL (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

164

ROUT_OUT.Value
Foundation Fieldbus Remote ROUT_OUT ValueValue of the
block output provided by the Host for back calculation in Rout mode
and to allow action to be taken under limited conditions or mode
changes.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFSEL1ST FFSEL3ST (FBCM)

FFSEL1ST FFSEL3ST (FBCM)


FF Param. Source:
SEL_1.Status SEL_3.Status
Type:
E:$FBSTATS Foundation Fieldbus Sel_1 Sel_3 StatusStatus of the respective
selected input (1-3) to the control selector.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFSEL1VL FFSEL3VL (FBCM)


FF Param. Source:
SEL_1.Value - SEL_3.Value
Type:
Real
Foundation Fieldbus Sel_1 Sel_3 Value Value of the respective
selected input (1-3) to the control selector.
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFSPHILM (FBCM)
FF Param. Source:
SP_HI_LIM
Type:
Real
Foundation Fieldbus Setpoint High LimitHighest setpoint operator
entry that can be used for the block.
Lock:
Supr
Default: 100
PtRes: FF DEVICE
Range: PV_SCALE +/- 10%

FFSPLOLM (FBCM)
FF Param. Source:
SP_LO_LIM
Type:
Real
Foundation Fieldbus Setpoint Low LimitLowest setpoint operator
entry that can be used for the block.
Lock:
Supr
Default: 0
PtRes: FF DEVICE
Range: PV_SCALE +/- 10%

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

165

FFSPRTDN (FBCM)

FFSPRTDN (FBCM)
FF Param. Source:
Type:
Real
Lock:
Supr
Default: +INF
PtRes: FF DEVICE
Range: Positive

SP_RATE_DN
Foundation Fieldbus Setpoint Rate DownRamp rate at which
downward setpoint changes are acted on in Auto mode, in PV units per
second. If ramp rate is set to zero or the block is in Auto mode, then
setpoint will be used immediately.

FFSPRTUP (FBCM)
FF Param. Source:
Type:
Real
Lock:
Supr
Default: +INF
PtRes: FF DEVICE
Range: Positive

SP_RATE_UP
Foundation Fieldbus Setpoint Rate UpRamp rate at which upward
setpoint changes are acted on in Auto mode, in PV units per second. If
ramp rate is set to zero or the block is in Auto mode, then setpoint will
be used immediately.

FFSPSTS (FBCM)
FF Param. Source:
SP.Status
Type:
E:$FBSTATS Foundation Fieldbus Setpoint StatusStatus of analog setpoint of
the block.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: Unsigned8

FFSPVAL (FBCM)
FF Param. Source:
SP.Value
Type:
Real
Foundation Fieldbus Setpoint ValueThe analog setpoint of the
block.
Lock:
Oper
Default: NaN
PtRes: FF DEVICE
Range: PV_SCALE +/- 10%

FFSTREV (PECM, FBCM)


FF Param. Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: 0-65535

166

ST_REV
Foundation Fieldbus Static RevisionStatic Revision Change.
Changes when any VIEW2 and/or VIEW4 data for the corresponding
Function/Resource Block changes.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFTRDIST (FBCM)

FFTRDIST (FBCM)
FF Param. Source:
TRK_IN_D.Status
Type:
E:$FBSTATS Foundation Fieldbus Track Input StatusStatus of the discrete input
used to initiate external tracking.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFTRDIVL (FBCM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: 0-OFF, 1-ON

TRK_IN_D.Value
Foundation Fieldbus Tracking Discrete ValueThe discrete input
that is used to initiate external tracking of the block output to the value
specified by TRK_VAL.

FFTRIPST (FBCM)
FF Param. Source:
TRIP Output Status
Type:
E:$FBSTATS Foundation Fieldbus Trip Output StatusStatus of the first discrete
output of the Integrator Block.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFTRIPVL (FBCM)
FF Param. Source:
Type:
Integer
Lock:
Supr
Default: 0
PtRes: FF DEVICE
Range: 0-OFF, 1-ON

R610
11/99

OUT_TRIP.Value
Foundation Fieldbus Trip ValueThe first discrete output of the
Integrator Block.

HPM Parameter Reference Dictionary


Honeywell Inc.

167

FFTRVLST (FBCM)

FFTRVLST (FBCM)
FF Param. Source:
TRK INPUT Status
Type:
E:$FBSTATS Foundation Fieldbus Track Input Status ValueStatus of the track
value.
Lock:
View
Default: Bad
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

FFTRVLVL (FBCM)
FF Param. Source:
TRK_VAL.Value
Type:
Real
Foundation Fieldbus Track Input ValueThis input is used as the
track value when external tracking is enabled by TRK_IN_D.
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

FFXDDECP (FBCM)
FF Param. Source:
Type:
Integer
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: Integer8

XD_SCALE.DecPt
Foundation Fieldbus Digit Decimal PointThe number of digits to
the right of the decimal point used with the value obtained from the
transducer for a specified channel.

FFXDS0 (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 0
PtRes: FF DEVICE
Range: 32 bit IEEE

168

XD_SCALE.EU0
Foundation Fieldbus Digit Scale ZeroThe low scale value used
with the value obtained from the transducer for a specified channel.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FFXDS100 (FBCM)

FFXDS100 (FBCM)
FF Param. Source:
Type:
Real
Lock:
Engr
Default: 100
PtRes: FF DEVICE
Range: 32 bit IEEE

XD_SCALE.EU100
Foundation Fieldbus Digit Scale 100The high scale value used with
the value obtained from the transducer for a specified channel.

FFXDUIDX (FBCM)
FF Param. Source:
XD_SCALE.UnitIndex
Type:
E:$FFEUIDX Foundation Fieldbus Transducer IndexThe engineering units code
used with the value obtained from the transducer for a specified
Lock:
View
Channel.
Default: 0
PtRes: FF DEVICE
Range: Unsigned16- 0-65,535

FL(i) (Array)
Type:
Lock:

Logical
Array Point Flag VariablesThe flags are mapped from either the HPM
box (defined by FLSTIX and NFLAG parameters), or from a serial
Determined by
interface IOP-connected device (when EXTDATA=IO_FL, mapping is
SPLOCK
defined by IOPNUM, FTANUM, DEVADDR, FLSTIX, and NFLAG
parameter
parameters).
Default: N/A
PtRes: HPM
Range: 1 ` i ` Array parameter NFLAG

FL(1)(12) (DevCtl, Logic)


Type:
Lock:

Logical
View; FL1-FL5
Prog; FL6
Oper; FL7-FL12
Default: FL2 = On,
rest = Off
PtRes: HPM
Range:

R610
11/99

Logic Slot FlagsTwelve flags, FL(1) to FL(12), are provided for each
logic slot. The states of flags FL(1) to FL(6) are controlled by the HPM
and cannot be changed by the user. FL(7)-FL(12) are assigned by the user
for controlling the path of the logic in the respective logic slot. Refer to the
HPM Control Functions and Algorithms manual for a detailed description
These flags are local to the logic slot and are different than the 127 flags
provided with each process module, and the 1023 flags provided in each
HPM box.

Off (Flag is off)


On (Flag is set)

HPM Parameter Reference Dictionary


Honeywell Inc.

169

FL(1)(127) (ProcMod)

FL(1)(127) (ProcMod)
Type:
Lock:

Logical
Local Flag VariablesEach process module in the HPM has 127 local flags
Determined
that can be used for implementing batch operations. These flags are local to the
by SPLOCK process module and are different than the 12 logic-slot flags, and the 1023 flags
parameter
provided in each HPM box.
Default: Off
PtRes: HPM
Range: Off (Flag is off)
On (Flag is set)

FL(1)(16,384) (HPM Box)


Type:
Lock:
Default:
PtRes:

Logical
Oper
Off
HPM

Box Flag VariablesEach HPM box has a set of 16,384 local flag variables
that can be used by process modules in this HPM to implement batch operations.
The first 2047 box flags are taggable. These flags are local to the HPM box and
are different than the 12 logic-slot flags, and the 127 flags provided in each
process module. The LCN index limit is 4095; there is no index limit for the
UCN. Array points can be used to address flags with an index greater than 4095.

Range:

Off (Flag is off)


On (Flag is set)
Helpful Hint: For the first 128 flags, the On state is alarmed.

FLDESC (Array)
Type:
Lock:
Default:
PtRes:
Range:

String_64
PtBld
Spaces
HPM
N/A

FL Array DescriptorDescribes FL data for the Array point.

FLOAT(1-16) (PECM, FBCM)


FF Param. Source:
Type:
Real
Lock:
Configurable
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

User configured
Floating Point Values 1-16Arrayed parameter of floating point
values mapped from FF parameters. The FF information depends on
the parameter to which it is mapped.

Helpful Hint: These parameters are mapped by the TPS Builder from the device manufacturers
supplied parameters or other fieldbus parameters not already mapped.

170

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FLSTIX (Array)

FLSTIX (Array)
Type:
Lock:
Default:
PtRes:
Range:

Real
Flag Array Start IndexDefines the flag array start index in Box FL variables
PtBld
or serial interface-connected devices.
0.0
HPM
0 to 99,999 (When EXTDATA = IO_FL, 0 can be a valid device index)
0 to 16,384 (When EXTDATA `IO_FL, 0 indicates that no flags are configured)

FORCE (HiLoAvg)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Forced Input Request FlagDefines whether the operator, a user-written
program, or an input connection has requested that an input be used as the forced
Oper
input for this algorithm.
Off
HPM
Off (No request to force an input)
On (Request has been made to force an input)
Helpful Hint: FORCE change requires FRCPERM = On.

FRCPERM (HiLoAvg)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Forced Input PermissiveDefines whether an operator or a user-written
program can force-select an input. FRCPERM must be On before the operator
Eng/PB
or a program can select an input to be used as a forced input to this algorithm.
Off
HPM
Off (Forced-selection function is disabled)
On (Forced- selection function is enabled)

FREQ6050(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

E:FRQ6050
Eng/PB
60Hz
HPM
0-60 Hz
1-50 Hz

Frequency 60/50HzDefines the 60/50 Hz frequency configuration needed for


a Low Level AI Mux or STI Temperature Transmitter. For the STI, if a
mismatch occurs between this parameter and the transmitter's internal 60 Hz/50
Hz frequency parameter, a database download from the STI IOP to the
transmitter will clear this condition.

FRQUTAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Average UCN Fetch Request Trip TimeThe average time in milliseconds


it takes to receive a response to this nodes UCN fetch requests.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

171

FRQUTMAX (NIM, HPM Box)

FRQUTMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Maximum UCN Fetch Request Trip TimeThe maximum time in


milliseconds it takes to receive a response to this nodes UCN fetch requests.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

FRSPTAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Average UCN Fetch Response Trip TimeThe average time in


milliseconds for this node to respond to fetch requests from other UCN nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

FRSPTMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Maximum UCN Fetch Response Trip TimeThe maximum time in


milliseconds for this node to respond to fetch requests from other UCN nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

FSELIN (HiLoAvg)
Type:
Lock:
Default:
PtRes:
Range:

E:PINP
Force Selected InputDefines the one of six inputs to be used as the forced
input to this algorithm.
Oper/PB
SelectP1
HPM
1-SelectP1 (Input P1 is the forced input)
2-SelectP2 (Input P2 is the forced input)
3-SelectP3 (Input P3 is the forced input)
4-SelectP4 (Input P4 is the forced input)
5-SelectP5 (Input P5 is the forced input)
6-SelectP6 (Input P6 is the forced input)
Helpful Hint: FSELIN change by an operator requires FRCPERM = On.

172

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FSTS (FlowComp)

FSTS (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

E:PVVALST
Flow Input Value StatusIndicates the current status of flow input F.
View
Bad
HPM
0-Bad (Value is bad and replaced with NaN)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

FTA1TYPE, FTA2TYPE (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$FTATYPE
View
None
HPM
0-None
1-TC
2-RTD

Type of FTA Connected to the LLMUX IOP or RHMUX IOPThe FTA


type applies to both FTA positions (1 and 2). The FTA supplies 16 points per
FTA for a total of 32 points.

FTACONN(1)(168) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$FTACON FTA connection to I/O module file. Indicates which FTA connector is
connected to this module. It is primarily used with the diagnostic displays.
View
nn = 140 specifies FTA connection for one of the 40 acting primaries. nn =
CONN_A
129168 specifies FTA connection for one of the 40 acting secondaries.
HPM
0-CONN_A (Module is connected to FTA connector A)
1-CONN_B (Module is connected to FTA connector B)

FTANUM (Array)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
1
HPM
1 to 10

IOP FTA NumberIndicates the FTA number of the serial interface IOP.

Helpful Hint: Only FTA Numbers 1 and 2 are presently applicable.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

173

FTAPRES(1)(168)

FTAPRES(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

174

Logical
View

IOP FTA Present FlagFor primary and secondary IOPs.

HPM
Off (FTA Missing)
On (FTA Present)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

G (FlowComp)

-GG (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
1.0
HPM
N/A

Specific Gravity InputIndicates the value of the measured or calculated


specific gravity or molecular weight.

GAINOPT (Pid)
Type:
Lock:
Default:
PtRes:
Range:

E:GAINOPT Gain (K) Option


Eng/PB
Lin
HPM
0-Lin (Applies linear gain, with overall gain (K) = KLIN)
1-Gap (Reduces the sensitivity of control action when the PV is within a narrow band around the
setpoint. If the PV is outside the gap, overall gain (K) = KLIN. If (SP - GAPLO) < PV <
(SP + GAPHI), K = KLIN times KGAP)
2-Nonlin (Makes control action proportional to the error (PV - SP) squared with overall
=KLIN times KNL, where KNL = NLFM plus (NLGAIN times PV - SP)/100)

gain (K)

3-Ext (Applies external gain. Overall gain (K) = KLIN times KEXT, where KEXT is the positive external
gain modifier)

GAPHI (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
> 0.0

Gap High LimitDefines the upper limit of the gap in the same engineering
units as the PV.

GAPLO (Pid)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Supr
0.0
HPM
> 0.0

Gap Low LimitDefines the bottom limit of the gap in the same engineering
units as the PV.

HPM Parameter Reference Dictionary


Honeywell Inc.

175

GENDESC (1)(12)

GENDESC (1)(12)
Type:
Lock:
Default:
PtRes:

Range:

String_8
PtBld
Blanks
NIM

Generic DescriptorsDefine up to 12 generic descriptors that can be assigned


to logic-slot parameters. As an example, six descriptors could be assigned to six
logic-slot inputs, two descriptors to the logic block flags which will describe the
current state of the logic slot based on the inputs, and two descriptors to the SO
outputs from the logic slot. Refer to the description of the PRMDESC
parameter, and to the HPM Control Functions and Algorithms manual for a
detailed description.
Permissible character set for the eight-character generic descriptors consists of all characters on the
Engineer' s Keyboard. Basically this set consists of alphabetics A-Z, numerics 0-9, and the following
special characters: space ! " % & ' ( ) * + - / : ; > < = ? _ , . $
Helpful Hint: Example: GENDESC(7) is the descriptor for parameter PRMDESC(7), etc.

GENDESC(nn)
Type:
Lock:
Default:
PtRes:

String_72
View
Blanks
HPM

Generic DescriptorUsed as additional display text to help the operator


diagnose potential problems with the IOP. It is primarily used with diagnostic
displays.
nn = 140 specifies one of the 40 acting primaries.
nn = 129168 specifies one of the 40 acting secondaries.

GISRC(14) (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes: HPM
Range:

General Input SourceSpecifies the Tag.Parameter source of General Input


Connection.

GIDSTN(14) (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes: HPM
Range:

Parameter Destination General Input ConnectionSpecifies the


RegPV/RegCtl parameter destination of the General Input Connection

GIENBL(14) (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes: HPM
Range:

176

General Input Connection Enable Flag

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

GOSRC(14) (RegCtl, RegPV)

GOSRC(14) (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes: HPM
Range:

Parameter Source of General Output ConnectionSpecifies the


RegPV/RegCtl parameter source of the General Output Connection

GODSTN(14) (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes: HPM
Range:

Parameter Destination General Output ConnectionSpecifies the


Tag.parameter destination of the General Output Connection

GOENBL(14) (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes: HPM
Range:

General Output Connection Enable Flag

GSTS
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:PVVALST
Gravity Input Value StatusIndicates the status of the gravity input value.
View
Normal
HPM
0-Bad (Value is bad and replaced with NaN)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

HPM Parameter Reference Dictionary


Honeywell Inc.

177

HBRDP (SECM)

-HHBRDP (SECM)
FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: 0-32767

None
Handle for Blind Record Data Pipe Communication

HIGHAL (AnalgIn, RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:

Range:

178

E:ALMTYPE
View
NoAlarm
NIM

Highest Alarm DetectedIndicates the highest alarm currently detected at


the data point. This parameter is used by the system to ensure that when two
or more different types of alarms occur on a point at the same time, the most
important or highest level alarm appears on the point's Group, Detail, and
Alarm Summary displays. For example, if both the PV High High and PV
High alarm priorities are set to Emergency, and both are in alarm, HIGHAL
contains the PVHH value.
NoAlarm (No alarm existslowest level alarm)
AdvDev (Advisory Deviation)
DevHi (Deviation High)
DevLo (Deviation Low)
PVRocN (PV Rate Of Change Negative)
PVRocP (PV Rate Of Change Positive)
PVHi (PV High)
PVHH (PV High High)
PVLo (PV Low)
PVLL (PV Low Low)
BadCtl (Bad Control)
BadPV (Bad PVhighest level alarm)
BOC (Bad Output alarm)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

HIGHAL (DevCtl, DigComp, DigIn, Flag, Logic)

HIGHAL (DevCtl, DigComp, DigIn, Flag, Logic)


Type:
Lock:
Default:
PtRes:
Range:

E:ALMTYPE
View
NoAlarm
NIM

Highest Alarm DetectedIndicates the highest alarm currently detected at


the data point. This parameter is used by the system to ensure that when two
or more different types of alarms occur on a point at the same time, the most
important or highest level alarm appears on the point's Group, Detail, and
Alarm Summary displays.
NoAlarm (No alarm has been detected)
OffNorm (Current PV state is not the configured PVNORMAL state. For a flag point, the
off-normal state (STATE1) is the alarmed state.)
UnCEvt (Uncertain event was detected. Does not apply to a flag point.)
CmdDis (Command Disagree; field device did not respond to commanded output state. Does not
apply to a flag point.)
BadPV (PV is bad)
C1 - C4ALM (1 to 4 custom logic alarms)
Chngofst (State has changed)
Cmdfail (PV failed to change after OP changed)
SVHI (SECVAR>SVHITP)
SVHH (SECVAR>SVHHTP)
BadSV (SECVAR is Bad)
OVRDI2 (Override Interlock I2)
OVRDI1 (Override Interlock I1)
OVRDI0 (Override Interlock I0)
OVRDSI0 (Safety Override Interlock)
BadCtl (Bad Control) (DevCtl and DigComp only)

HIGHAL (FBCM)
FF Param. Source:
None
Type:
E:ALMTYPE High AlarmHighest Alarm Detected. When two or more alarms
occur on a point at the same time, the most important of the highest
Lock:
View
alarm appears on the point's Group, Detail, and Alarm Summary
Default: NoAlarm
displays.
PtRes: NIM
Range: 0-NOALARM, 1-OFFNORM, 5-DEVLO,
6-DEVHI, 9-PVLO, 10-PVHI, 11-PVLL,
12-PVHH, 14-BADPV

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

179

HIGHALPR (AnalgIn, RegCtl, RegPV)

HIGHALPR (AnalgIn, RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Highest Level Alarm's PriorityDefines the priority of the highest alarm
currently detected at the data point. Associated with HIGHAL.
View
NoAction
NIM
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

HIGHALPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
View
Default: NoAction
PtRes: NIM

Range:

None
High Alarm PriorityPriority of the highest priority alarm currently
detected for this point. This value is mapped from the FF alert priority
parameter as follows:
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1
Emergncy, High, Low, JnlPrint, Printer, Journal, NoAction
Emergncy, High, Low, JnlPrint, Printer,
Journal, NoAction

HISVPEAK (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
>0

Highest Peak SECVAR ValueThe highest peak value of the SECVAR


parameter since the most recent reset of maintenance statistics.

HLCALIB(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

180

Logical
Eng/Pb

HLAI in Calibration FlagShows which HLAIs are presently in calibration

HPM
Off - Calibration is not in progress
On - Calibration is in progress

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

HOLDCMD (RampSoak)

HOLDCMD (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

Hold Command FlagIf On, allows users to hold the ramp or soak segment at
its current position to customize the guaranteed ramp and soak function.

HOUR (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 to 23

Current HourThe value of the LCN time in the HPM.

Only full array access is supported.

HWYCTLST (UCN)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$NODFSTA UCN Network Functional State


Supr
Basic
NIM
Full (All LCN devices can do read/write operations to this UCN)
Basic (AM and CM cannot write to this UCN)

HPM Parameter Reference Dictionary


Honeywell Inc.

181

I02 (DevCtl, DigComp)

-II02 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Engr
Off
HPM

Override Interlocks for Output States 0-2Override interlocks force the


commanded output to a specific state regardless of the condition of the
permissive interlocks or the previous point state. The operator and user program
cannot change the output state when any override interlock is On. An override
interlock is provided for each of the three states. Refer to the HPM Control
Functions and Algorithms manual for a detailed description.
Off (Override interlock has no effect on the point state)
On (Override interlock sets the point to the respective state)
Helpful Hint: 1.
2.
3.
4.

When I0 is On, forces the output to STATE0, regardless of the permissives


or any other overrides.
When I1 is On and I0 is Off, forces the output to a STATE1, regardless
of the permissives or any other overrides.
When I2 is On and I0 and I1 are both Off, forces the output to STATE2
regardless of the permissives or any other overrides.
I0-I2 change by the engineer, requires PTEXECST = InActive
or PNTSTATE = Idle for each interlock.

I0CONF (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Oper
Off
HPM
N/A

Override Interlock 0 Alarm Confirmation FlagIndicates that the Override


Interlock 0 Alarm needs to be confirmed.

I0DESC-I2DESC (DigComp)
Type:
Lock:
Default:
PtRes:

String_8
Engr
Blank
HPM

Range:

8 Character String

I0-I2 Alarm DescriptorThe override Interlock for States 0, 1, or 2 indicating


which text should be copied into the OVRDDESC parameter when an override
alarm occurs. The text appears in the Alarm Display and can be configured to
indicate the cause for the alarm.

I1CONF (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

182

Logical
Oper
Off
HPM
N/A

Override Interlock 1 Alarm Confirmation FlagIndicates that the Override


Interlock 1 Alarm needs to be confirmed.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

I2CONF (DigComp, DevCtl)

I2CONF (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Oper
Off
HPM
N/A

Override Interlock 2 Alarm Confirmation FlagIndicates that the Override


Interlock 2 Alarm needs to be confirmed.

IDXFLOAT (1-16) (PECM, FBCM)


FF Param. Source:
None
Type:
Blind
Index To NumericThis is an arrayed parameter that contains the
object dictionary index of the FF parameter that is mapped to this
Lock:
PtBld
generic numeric parameter.
Default: 0
PtRes: IOP
Range: Object dictionary index valid range.

IDXUS16 (1-16) (PECM, FBCM)


FF Param. Source:
None
Type:
Blind
Index to IntegerThis is an arrayed parameter that contains the object
dictionary indexes of the FF parameter that is mapped to this generic
Lock:
PtBld
integer parameter.
Default: 0
PtRes: IOP
Range: Object dictionary index valid range.

IDXUS32 (1-16) (PECM, FBCM)


FF Param. Source:
None
Type:
Blind
Index to IntegerThis is an arrayed parameter that contains the object
dictionary indexes of the FF parameter that is mapped to this generic
Lock:
PtBld
32-bit integer parameter.
Default: 0
PtRes: IOP
Range: Object dictionary index valid range.

IDXUS8 (1-16) (PECM, FBCM)


FF Param. Source:
None
Type:
Blind
Index to FlagThis is an arrayed parameter that contains the object
dictionary index of the FF parameter that is mapped to this generic flag
Lock:
PtBld
parameter.
Default: 0
PtRes: IOP
Range: Object dictionary index valid range.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

183

IDXVS (1-16) (PECM, FBCM)

IDXVS (1-16) (PECM, FBCM)


FF Param. Source:
None
Type:
Blind
Index to StringThis is an arrayed parameter that contains the object
dictionary index of the FF parameter that is mapped to this generic
Lock:
PtBld
string parameter.
Default: 0
PtRes: IOP
Range: Object dictionary index valid range.

IN (1-8) (FBCM)
FF Param. Source:
Configurable through link object
Type:
Real
INThe value of an analog point for output connections from TPSN to
the subscriber input connections on the fieldbus network.
Lock:
Prog
Default: NaN
PtRes: IOP
Range: Floating Point

IN012 (GenLin)
Type:
Lock:
Default:
PtRes:
Range:

Real
Input Coordinates 012Define the input value at the respective coordinate.
IN0 <IN1 <IN2 ......., <IN12
Supr
NaN
HPM
> prev. coord.
< next coord.

IND(1-8) (FBCM)
FF Param. Source:
Type:
Integer
Lock:
Prog
Default: OFF
PtRes: IOP
Range: 0-OFF
1-ON

184

Configurable through link object


High Alarm PriorityThis is an arrayed parameter. It contains the
value of a discrete point for non-control output connections from TPSN
to the subscriber input connection on the fieldbus network.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INITMAN

INITMAN
Type:
Lock:
Default:
PtRes:

Logical
View
Off
HPM

Initialization Manual FlagWhen On, indicates that this point is in


Initialization Manual. The mode of the point does not change; however, INIT
appears on the points detail or group display to indicate that the point is in
Initialization Manual. While the point is in Initialization Manual, an operator,
supervisor, or engineer cannot change the points output. The output is
indisposable because initialization is being requested from downstream. Upon
leaving Initialization Manual, the points output is initialized from the points
secondary as determined by the points output connection.

Range:

Off (Mode ` Initialization Manual)


On (Mode = Initialization Manual)
Helpful Hint: OP changes with Operator, Supervisor, or Engineer access level, requires MODE = Man
and INITMAN = Off. SP changes with Operator, Supervisor, or Engineer access level, for non-PID
algorithms requires MODE = Auto and INITMAN = Off, while for PID algorithms requires that MODE
= Auto, and also that INITMAN = Off and PTEXECST = Active if PVTRACK = Track.

INITMAN (DigComp, DevCtl, RegCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Initialization Manual FlagOn, indicates that an output is storing to a DO
point that has its INITREQ flag set and the point is forced into initialization.
View
When the DO point becomes available, the initialization state is cleared.
On
HPM
Off (Mode ` Initialization Manual)
On (Mode = Initialization Manual)

INITREQ(1)(4) (RegCtl)
Type:
Lock:
Default:
PtRes:

Range:

R610
11/99

Logical
View
Off
HPM

Initialization Request Flags (14)Indicates whether an initialization request


has been made. Each flag represents a request to the primary point pushing to
the corresponding input to be initialized as follows:
Flag 1: SP or X1
Flag 2: RATIO or X2
Flag 3: X3
Flag 4: X4
Off (No initialization request)
On (Initialization request)

HPM Parameter Reference Dictionary


Honeywell Inc.

185

INITREQ (Array)

INITREQ (Array)
Type:
Lock:

Logical
View

Initialization Request FlagIndicates whether a Serial Interface-connected


device can be written to, where OFF = yes, or ON = no. The flag is always OFF
if EXTDATA = None.

Default: On when EXTDATA = IO_FL, IO_NN, or IO_STR


Off when EXTDATA = None
PtRes: HPM
Range: Off (EXTDATA=None, or Serial interface-connected device can be written to)
On (Serial interface-connected device cannot be written to)

INITREQ (AO, DO)


Type:
Lock:
Default:
PtRes:

Range:

Logical
View
On
HPM

Initialization Request FlagWhen On, indicates that control strategies in the


HPM cannot manipulate the output to the field. It is set to ON when:

the PWM type output is configured


the point is inactive
the module is idle
there is a soft failure such that the channel is not working
The output is connected to standby-manual device
Off (No initialization request)
On (Initialization request)

INITREQ(0)(2) (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:

Logical
View
On
HPM

Range:

Off
On

Initialization Request FlagWhen On, indicates that CL programs or logic can


not change the output to State(i), where i = 0, 1, or 2.

INITREQ (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: IOP
Range: 0-OFF
1-ON

186

None
Initialization RequestInitialization Request. Derived from status
member of feedback parameters (BKCAL_OUT, RCAS_OUT,
ROUT_OUT, etc).

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

INITVAL

INITVAL
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A

Initialization ValueIndicates the value to which the primary point is to be


initialized.

STATE 1
BOX
(Upper)
STATETXT (1)

STATE 0
BOX
(Lower)
STATETXT (0)

PVRAW
State

INPTDIR =
Direct

INPTDIR =
Reverse

ON

PV = ON.
State 1 Box is
lighted.
State 0 Box is
extinguished.

PV = OFF.
State 0 Box is
lighted.
State 1 Box is
extinguished.

OFF

PV = OFF.
State 0 Box is
lighted.
State 1 Box is
extinguished.

PV = ON.
State 1 Box is
lighted.
State 0 Box is
extinguished.

2065

Figure I -1 INPTDIR vs. Display Indicators

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

187

INPCONCT

INPCONCT
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

None
This parameter has been added to provide compatibility with fieldbus
requirements

INPTDIR (FBCM)
FF Param. Source:
Type:
E:POLARITY
Lock:
Engr
Default: Direct
PtRes: IOP
Range: 0-Direct
1-Reverse

Bit 0 of IO_OPTS (Invert)


Digital Input DirectionDefines the contact conditions required to
light the upeer or lower boxes on a group or detail display for a digital
input point.

INPTDIR (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

E:POLARITY Digital Input DirectionDefines the contact conditions required to light the
upper or lower boxes on a Group or Detail Display for a digital input point.
Eng/PB
See Figure I-1.
Direct
HPM
0-Direct
State 0 (lower) box lighted =>PVRAW = Off
State 1 (upper) box lighted =>PVRAW = On
1-Reverse
State 0 (lower) box lighted =>PVRAW = On
State 1 (upper) box lighted =>PVRAW = Off

INPUTS (FBCM)
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

188

None
This parameter has been added for compatibility with fieldbus
requirements.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IOLASTS (HPM Box)

IOLASTS (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Logical
I/O Link Cable A Status
View
Off
HPM
Off (I/O Link cable A not in error)
On (I/O Link cable A in error)

IOLBSTS (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Logical
I/O Link Cable B Status
View
Off
HPM
Off (I/O Link cable B not in error)
On (I/O Link cable B in error)

IOLCHAER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

I/O Link Channel A Error Count

IOLCHASL (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

I/O Link Channel A Silence Count

IOLCHBER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
View
0
HPM
>0

I/O Link Channel B Error Count

HPM Parameter Reference Dictionary


Honeywell Inc.

189

IOLCHBSL (HPM Box)

IOLCHBSL (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

I/O Link Channel B Silence Count

IOLCHERT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
EngOnly
10
HPM
>0

I/O Link Channel Error ThresholdDefines the acceptable number of I/O


Link channel errors per minute before disabling the periodic I/O Link channel
swap.

IOLCMD (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$IOLCMD
I/O Link Command
EngOnly
None
HPM
0-None (No effect)
1-SelChnA (Select I/O Link Channel A)
2-SelChnB (Select I/O Link Channel B)
3-EnbPerSw (Enable periodic swapping of IOL cables)
4-DisPerSw (Disable periodic swapping of IOL cables)
5-RsIoLCom (Reset IOL communication error count to 0)

IOLHWREV (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_2
View
Blank
HPM

HPMM I/O Link Interface Processor Card Hardware Revision

IOLPERSW (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

190

I/O Link Periodic Cable Swap


View
N/A
HPM
0-Disable (Swapping of I/O Link cables A & B is disabled)
1-Enable (Swapping of I/O Link cables A & B is enabled)

E:ENBLSTAT

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IOLPSERR (ProcMod)

IOLPSERR (ProcMod)
Type:
Lock:
Default:
PtRes:

E:Pastatus
View
NoError
HPM

Range:

Helpful Hint:
NoError

I/O Link Poststore Failure Option Contains the IOL Poststore PA status
failure code, or null.

This parameter should be used with IOLPSOPT.

IOLPSOPT (ProcMod)
Type:
Lock:
Default:
PtRes:

E:$IOLPSOPT
Engr
Fail
HPM

Range:

Helpful Hint: The program should check the value of IOLPSERR if this parameter is continue.
Fail (program fails on a bad IOL store)
Continue (program continues on a bad IOL store)

I/O Link Poststore Failure Option

IOLREV (HPM Box)


Type:
Lock:
Default:
PtRes:

Integer
View
Blank
HPM

HPMM I/O Link Software Revision

Range:

IOLVERS (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
View
Blank
HPM

HPMM I/O Link Software Version

HPM Parameter Reference Dictionary


Honeywell Inc.

191

IOMACTYP(1)(168)

IOMACTYP(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

E:$PMMDTY
IOP Actual Type Actual type of IOP at module address.
This should match the configured type.
View
None
HPM
None (Not Configured)
LLAI (Low Level Analog Input)
HLAI (High Level Analog Input)
DI (Digital Input)
DO (Digital Output)
AO (Analog Output
HPMM (HPM Module)
LLMUX (Low Level Analog Input Multiplexer) Also includes RHMUX (Remote Hardened
Analog Multiplexer)
STIM (Smart Transmitter Interface Module)
PI (Pulse Input)

IOMCARD(1)(168) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
1-15

I/O module card position for the acting primary/secondary (used for
diagnostic displays).
nn = 1 - 40 correspond to card positions of the 40 acting primaries
nn = 129 - 168 correspond to card positions of the 40 acting secondaries

IOMCARDA(1)(40) (HPM Box)


Type:
Lock:

Integer
PtBld

I/O module A card position. 140 specifies one of the 40 logical I/O
modules. The corresponding IOP must be connected to FTA connector
A. Applies to the primary IOP only.

Default: 0 in IOP database;


per PKGOPT on GDF
PtRes: HPM
Range: 0 - 15 (0 specifies Not Connected)

IOMCARDB(1)(40) (HPM Box)


Type:
Lock:

Integer
PtBld

I/O module B card position. 1-40 specifies one of the 40 logical


I/O modules. The corresponding IOP must be connected to FTA
connector B. Applies to primary IOP only.

Default: 0 in IOP database;


none on GDF
PtRes: HPM
Range: 0 - 15 (0 specifies Not Connected)

192

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IOMCHAER(1)(168)

IOMCHAER(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 - 255

IOP Channel A Error Countfor a specific IOP

IOMCHASL(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 - 255

IOP Channel A Silence Countfor a specific IOP

IOMCHBER(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 - 255

IOP Channel B Error Countfor a specific IOP

IOMCHBSL(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 - 255

IOP Channel B Silence Countfor a specific IOP

IOMCMD (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$IOMCMD IOP Module CommandIndicates IO module state, or whether to swap


redundant pairs.
Oper
None
HPM
None
Run
Idle
Swap

HPM Parameter Reference Dictionary


Honeywell Inc.

193

IOMCOMER(1)(168)

IOMCOMER(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

E$:IOMCOMMIOP
IOP Communications Error Statusfor a
specific IOP
View
N/A
HPM
None - No error
Invalert - Invalid alert; message bit problem
Invdest - Invalid destination
Invchcnt - Invalid character count; message corrupted
Invsourc - Invalid source
Invcmd - Invalid command
Checksum - Checksum error
No_resp - No response
Chtimout - Channel time out
Msgovrun- Message overrun
Gaperror - Gap error; message gap too long
Lpbckerr - Loopback error
Nth_0 - Next token holder equals zero
Tknrecov - Token recovery in progress
Rplbufov - Reply buffer overflow

IOMFILE(1)(168) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
I/O Module File Position for the Acting Primary/Secondary
View
(used for diagnostic displays).
N/A
nn = 1 - 40 are file positions of the 40 acting primaries.
HPM
nn = 129 - 168 are file positions of the 40 acting secondaries.
0 - 8 (0 specifies Not Connected)

IOMFILEA(1)(40) (HPM Box)


Type:
Lock:

Integer
PtBld

I/O Module A File Position1-40 specifies one of the 40 logical I/O


modules. The corresponding IOP must be connected to FTA connector
A. Applies to the primary IOP only.

Default: 0 in IOP data base;


per PKGOPT on GDF
PtRes: HPM
Range: 0 - 8 (0 specifies Not Connected)

IOMFILEB(1)(40) (HPM Box)


Type:
Lock:

Integer
PtBld

I/O Module B File Position1-40 specifies one of the 40 logical I/O


modules. The corresponding IOP must be connected to FTA connector
B. Applies to the primary IOP only.

Default: 0 in IOP data base;


none on GDF
PtRes: HPM
194

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IOMFWREV(1)(168)

Range:

0 - 8 (0 specifies Not Connected)

IOMFWREV(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Ascii_2
IOP Card Firmware Revision Status
(This is not the same as the external letter code on the card)
View
N/A
HPM
X.Y X = Version, Y = Revision
(For Release 300, X = 3)

IOMHWREV(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Ascii_2
IOP Card Hardware Revision Status
The status of R300 boards appears as $2x, the status of R210
View
appears as $0x, where x is the version (0=A, 1=B, 2=C, etc.)
N/A
HPM
Hexadecimal characters 00FF

IOMLHFST(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$IOMHF
Input/Output Processor Last Hard Fail StatusRefer to the HPM Service
Manual for a detailed description and the recommended corrective action.
View
N/A
HPM
0-Unknown (Unknown Status)
1-PowerDwn (This IOP Powered Down)
2-InvPrgEx (Invalid Program Execution)
3-EpromErr (EPROM Checksum Error)
4-RamCntEr (RAM Contents Error)
5-RamAdrEr (RAM Addressing Error)
6-DpaError (Device Physical Address Error)
7-DsaError (Device Soft Address Error)
8-RxBufOfl (I/O-Link Receive Buffer Overflow)
9-IOLJaber (I/O-Link Jabber Circuit Failure)
11-BadPgJmp (Illegal Value of Case Control)
12-AdCIncmp (A-to-D Conversion Incomplete)
13-AdOutOvf (A-to-D Output Value Overflow)
14-AdOutUdf (A-to-D Output is less than Zero)
15-AdCCalEr (A-to-D Calibration is incorrect)
16-BadDcLtc (Bad DC LTC)
17-Dmt_Tmot (Dead Man Timer Timeout)
18-MLtOutFl (Multiple Output Failures)
20-BadDaRng (Bad D-to-A Range)
21-MstrTmot (Master 68 k Timeout)

HPM Parameter Reference Dictionary


Honeywell Inc.

195

IOMNUM

IOMNUM
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
N/A
HPM
1 to 40

IOP NumberIOMNUM specifies the IOP on the I/O Link that this point
references for its process data.

IOMOPER(1)(168) (HPM Box, IOP)


Type:
Lock:
Default:
PtRes:
Range:

E:$PRIMSEC
Input/Output Processor In Operation
View
N/A
HPM
0-Primary (Primary IOP is operating)
1- Secondry (Secondary IOP is operating)

IOMREALT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$PMMDTY
Actual Input/Output Processor Type
View
None
HPM
0-None (Not Configured)
1-LLAI
2-HLAI (High-Level Analog Input)
3-DI (Digital Input)
4-DO (Digital Output)
5-AO (Analog Output)
7-LLMUX (Low-Level Analog Input Multiplexer) also includes RHMUX (Remote Hardened
Analog Multiplexer)
14-STIM (Smart Transmitter Interface Module)
17-PI (Pulse Input)

IOMRECHN(1)(168) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

196

E:$RECCHN
View
N/A
HPM
ChannelA
ChannelB

IOP Receive Channel

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IOMSEVER(1)(168) (HPM Box)

IOMSEVER(1)(168) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$SEVERTY
View

Error Severity Based on Input/Output Processor State


nn = 1 - 40 specifies the severity of 1 of the 40 acting primaries
nn = 129 - 168 specifies the severity of 1 of the 40 acting secondaries

HPM
Ok (I/O Processor has no errors and is OK)
Fail (I/O Processor has failed)
Inform (I/O Processor should be calibrated soon)
Warning (I/O Processor is on the verge of failing)

IOMSTS(1)(168) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$IOMSTS Input/Output Module State


View
nn = 1 - 40 specifies the status of 1 of the 40 acting primaries
N/A
nn = 129 - 168 specifies the status of 1 of the 40 acting secondaries
HPM
0-PowerOn (Transient state when power is turned on)
1-Idle (In the Idle State)
2-OK (Running)
3-NoResp (No Response)
4-IdleSF (In the Idle State and has a Soft Failure)
5-SoftFail (Running and has a Soft Failure)
6-CommErr (Communication Error)
7-ConfgMis (Configuration Mismatch)
8-NotConfg (This IOP is Not Configured)
9-NonExist (This IOP does Not Exist)
UnAvail (Transient state during which status for this IOP is unavailable)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

197

IOMTYPE(1)(168) (IOP)

IOMTYPE(1)(168) (IOP)
Type:
Lock:
Default:
PtRes:

E:$PMMDTY
View
None
HPM

Input/Output Processor Type

Range:

0-None (Not Configured)


1-LLAI (Low Level Analog Input)
2-HLAI (High Level Analog Input, 16 slot)
3-DI (Digital Input, 32 slot)
4-DO (Digital Output, 32 slot)
5-AO (Analog Output, 8 slot)
7-LLMUX (Low Level Analog Input Multiplexer) also includes RHMUX (Remote Hardened
Analog Multiplexer)
10-SI (Serial Interface)
14-STIM (Smart Transmitter Interface Module)
16-DISOE (Digital Input, Sequence of Events)
17-PI (Pulse Input)
24-AO16 (Analog Output, 16 slot)
25-DO32 (Digital Output, 32 slot)

IOMTYPE (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

198

E:$PMMDTY
Configured Input/Output Processor Type
PtBld
NotConfg
HPM
0-NotConfg (Not Configured)
1-LLAI (Low-Level Analog Input)
2-HLAI (High-Level Analog Input)
3-DI (Digital Input)
4-DO (Digital Output)
5-AO (Analog Output)
7-LLMUX (Low Level Analog Input Multiplexer) also includes RHMUX (Remote Hardened
Analog Multiplexer)
10-SI (Serial Interface)
14-STIM (Smart Transmitter Interface Module)
16-DISOE (Digital Input, Sequence of Events)
17-PI (Pulse Input)
24-AO-16 (Analog Output)
25-DO-32 (Digital Output)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IONTOKEN (HPM Box)

IONTOKEN (HPM Box)


Type:
Lock:
Default:
PtRes:

Integer
View
N/A
HPM

IOP Next Token Holder

NOTE
This parameter is available to the nodes on the LCN, but cannot be accessed on the UCN, either by
HPM/CL programs or print connections.

Range:

0, or 128 to 255

IOPDESC(1 - 40)
Type:
Lock:
Default:
PtRes:

String_8
View
Spaces
HPM

Range:

Helpful Hint: An 8-character string is read from the IOP's EPROM and stored in the HPMM. The text
string appears on the IOP Detail Display. Even if the IOP fails, an operator can identify the IOP/FTA for
maintenance. Not all IOPs have this feature yet.
8 characters

IOP DescriptionProvides an 8-character description of the IOP.

IOPIDAY (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM

HPMM I/O Link Personality Creation Date- Day

IOPIMON (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
View
0
HPM
N/A

HPMM I/O Link Personality Creation Date- Month

HPM Parameter Reference Dictionary


Honeywell Inc.

199

IOPIYEAR (HPM Box)

IOPIYEAR (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
N/A

HPMM I/O Link Personality Creation Date- Year

IOPNUM (Array)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
N/A
HPM
1 to 127

Serial Interface IOP Module NumberDefines the module number of the


serial interface IOP.

IOPSTR1(1)(40) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_64
View
Spaces
SI
N/A

IOP String for FTA #1Contains user-defined string data shown in the Box
Detail display such as the FTA application name, its revision number, and date.
NN = 1-40 specifies the Serial Interface IOP module number.

IOPSTR2 (1)(40) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_64
View
Spaces
SI
N/A

IOP String for FTA #2Contains user-defined string data shown in the Box
Detail display such as the FTA application name, its revision number, and date.
NN = 1-40 specifies the Serial Interface IOP module number.

IORECCHN (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

200

E:$RECCHN I/O Link Receive CableThe cable the I/O module is currently listening on.
PtBld
None
HPM
A (I/O module is listening on Cable A)
B (I/O module is listening on Cable B)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IOREDOPT(1)(40) (HPM Box)

IOREDOPT(1)(40) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$REDOPT
PtBld
NonRedun
HPM
0-Redun
1-NonRedun

IOP Redundancy OptionIndicates if an IOP is configured for redundancy

IOSTKNDR
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 to 32767

IOP Token Drop Count

IOSCNCYC(1 40)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0.0
HPM
0 - 16

Control base cycle number


The index to this parameter specifies the IOP number for which this information
is being accessed.

IOSCNPER(1 40) (AnalgIn)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
IO data Scan Period the I/O data scan period in seconds for IO processors
that support Analog Input point types. The index to this parameter specifies the
PtBld
IOP number for which this information is being accessed.
0.0
HPM
0.0, 0.0625, 0.125, 0.25, 0.5, 1.0

HPM Parameter Reference Dictionary


Honeywell Inc.

201

K (AutoMan)

-KK (AutoMan)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
N/A

Gain Constant for X2 InputRefer to the HPM Control Functions and


Algorithms manual for a detailed description.

K (MulDiv, RegCtl Summer)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM

Overall Gain

K (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
0.0 to 240.0

Overall GainValue of K depends on the chosen gain option. Refer to the


HPM Control Functions and Algorithms manual for a detailed description.

K (PosProp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
0.0 to 10.0

Gain Constant

K1 (PidErfb)
Type:
Lock:
Default:
PtRes:
Range:

202

Real
Supr
0.0
HPM
0.0 to 1.0

External Reset Feedback Gain

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

K1 (PIDPosPr)

K1 (PIDPosPr)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
0.0 to 10.0

Gain Constant

K1K2 (RatioCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
N/A

K1 = Ratio Scale Factor; K2 = Scale Factor for X2 InputWhen used in


conjunction with the Calcultr algorithm, K1 must be equal to C1, and K2 must be
equal to C2.

K1K3 (MulDiv)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM

Gain Constants for X1X3 Inputs

K1K4 (RegCtl Summer)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM

Gain Constants for X1X4 Inputs

K1K4 (IncrSum)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
> 0.0

Gain Constants for X1X4 Inputs

KEXT(Pid)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Prog
1.0
HPM
0.0 to 240.0

External Gain ModifierDefines the external gain modification factor. It can


be entered by a user-written program, or it can be an input from another data
point.

HPM Parameter Reference Dictionary


Honeywell Inc.

203

KEYWORD

KEYWORD
FF Param. Source:
None
Type:
String -8
Keyword An eight-character descriptor that is used to describe an
important aspect of this particular data point. For example, in Figure NLock:
PtBld
1 (see NAME) the keyword for the data point is REFLUX.
Default: Blank
PtRes: NIM
Range: Alphabetics A-Z (upper case only).
Numerics 0-9 (an all numeric keyword is not allowed).
Underscore (_) cannot be used as the first character or the last character in a keyword.
Consecutive underscores are not allowed. Do not use quote marks (").

KFF (PidFf)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
> 0.0 to < 1.0

Gain for Feed Forward InputScale factor which is used in converting the FF
input value to percent.

KGAP (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
00 to 1.0

Gap Gain FactorDefines the gain-modification factor.

KLIN (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
0.0 to 240.0

Linear Gain FactorDefines the linear gain in percent per percent.

KNL (Pid)
Type:
Lock:
Default:
PtRes:
Range:

204

Real
View
N/A
HPM
N/A

Nonlinear Gain ModifierIndicates the calculated value of the nonlinear gain


modifier.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

L(1)(12) (DevCtl, Logic)

-LL(1)(12) (DevCtl, Logic)


Type:
Lock:
Default:
PtRes:
Range:

Logical, Real
View
N/A
HPM
Real

Value of the External InputL(1)L(12) are the 12 inputs to a logic slot


fetched with input connections from other points. Each input can be a Boolean,
an Integer, or a Real number. Integer input values are converted to real numbers
before being stored into the database.

Helpful Hint: L, if accessed from the LCN, must be accessed as a Logical data type.

LASTPV (FBCM)
FF Param. Source:
AI: OUT.Value; PID: PV.Value
Type:
Real
Last PVLast good value of the PV before it went bad.
Lock:
View
Default: NaN
PtRes: IOP
Range: Floating Point

LCNRECHN (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$RECCHN LCN Receive ChannelIndicates the LCN channel to which the NIM is
listening.
View
ChanneLA
HPM
0-ChanneLA (NIM is listening to LCN channel A)
1-ChanneLB (NIM is listening to LCN channel B)

LDNGNODE (HPM Box)


Type:
Integer
Lock:
View
Default:
PtRes: HPM
Range:

R610
11/99

UCN Node Performing Personality Image Load to This Node

HPM Parameter Reference Dictionary


Honeywell Inc.

205

LIBADOPT (DevCtl, Logic)

LIBADOPT (DevCtl, Logic)


Type:
Lock:
Default:
PtRes:
Range:

E:$LIBADOP
Logic Bad Input Handling OptionIf a Boolean input is not successfully
fetched for an input connection to the logic slot, its value is defaulted to one of
PtBld
the values (Off, On, Hold) selected through this parameter. Refer to the HPM
Hold
Control Functions and Algorithms manual for a detailed description.
HPM
0-On (On state is substituted for bad input)
1-Off (Off state is substituted for bad input)
2-Hold (Last good value is substituted for bad input)

LIBRYNUM
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
1
NIM
1-3

NIM Library NumberSpecifies the number of the NIM Library being


configured. For Parameter Entry Display use only.

LIBRYTXT(1)(1000)
Type:
Lock:
Default:
PtRes:
Range:

String_8
PtBld
N/A
NIM
N/A

NIM Library Text

LIDESC(1)(12) (DevCtl)
Type:

String_8
Input DescriptorExternal input descriptors.
in an Array
(1..12)
Lock:
Engr
Default: Blank
PtRes: HPM
Range: 8 Character String

LIMITS
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

206

None
This parameter has been added for compatibility with fieldbus
requirements.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LINEPERD (1)(168)

LINEPERD (1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Real
Line Period in Microseconds
View
N/A
HPM
15616.0 to 21759.0

LINKCMD (SECM)
FF Param. Source:
Type:
E:$LINKCMD
Lock:
Engr
Default: Null
PtRes: IOP
Range: 0-Null
1-Shutdown
2 -Restart

None
Link Command Provides commands by which a user can shutdown
or restart a fieldbus link. Can be used for any of the four links
connected to the fieldbus IOP/FTA

LINKSTAT (SECM)
FF Param. Source:
Type:
E:$LINKSTA
Lock:
View
Default: Null
PtRes: IOP
Range: 0-NULL
1-OK
2-BAD

R610
11/99

None
Link Status Displays the staus of a fieldbus IOP link. Additional
information on the link status is contained in the LNKDTLST
parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

207

LISRC(1)(12) (DevCtl, Logic)

LISRC(1)(12) (DevCtl, Logic)


Type:

Universal
Logic Input Connection SourceDefine the parameters whose current values
are to be supplied to one or more of up-to-12 logic slot or Device Control inputs.
Ent.Prm
The parameters can be specified using the "Tagname.Parameter" format or the
Lock:
PtBld
hardware reference address format. Refer to the HPM Control Functions and
Default: null.null
Algorithms manual for a detailed description.
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.
Some possible input-connection sources are
a. AnalgIn slot Tagname.PV
b."DigIn slot Tagname.PVFL"
c."Logic slot Tagname.SO(nn)" where nn = 124
d."Logic slot Tagname.Fl(nn)" where nn = 112
e.Logic slot Tagname.NN(nn) where nn = 1-8
f."ProcMod slot Tagname.Fl(nnn)" where nnn = 1127
g.ProcMod slot Tagname.NN(nn) where nn = 180
h.RegCtl slot Tagname.PV
i.RegPV slot Tagname.PV
j."Box Flag slot Tagname.PVFL
k.Box Numerics slot Tagname.NN where nnnnn = 1-16,384
l."!Box.FL(nnnn)" for a box flag that resides in the same box where nnnnn = 116,384
m."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the NIM UCN address, xx is the HPM box number, and
nnnn = 14095 (data access limit)
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DI (Digital Input)
mm is the IOP Card number (140)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

208

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LIVELIST (SECM)

LIVELIST (SECM)
FF Param. Source:
Type:
String
Lock:
View
Default: 0
PtRes: IOP
Range: N/A

Management Information Block: Network Management


List of Live Devices This parameter contains a bitmap of the devices
that are alive on the fieldbus link. The bit string includes one bit for
each possible device address. A value of one (1) indicates that the
device is present on the link.

LMREV (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:POLARITY Local Manual PolarityIndicates whether point processing inverts the local
manual input value.
Engr/PB
Direct
HPM
Direct (Value is not inverted)
Reverse (Value is inverted)

HPM Parameter Reference Dictionary


Honeywell Inc.

209

LMSRC (DevCtl, PosProp, PIDPosPr)

LMSRC (DevCtl, PosProp, PIDPosPr)


Type:

Universal
Local Manual SourceThe input connection for the local manual input.
Only inputs with logical data types are valid.
Ent.Prm
Lock:
PtBld
Default: Null.null
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.
Some possible input-connection sources are
a."DigIn slot Tagname.PVFL"
b."Logic slot Tagname.SO(nn)" where nn = 124
c."Logic slot Tagname.Fl(nn)" where nn = 112
d."ProcMod slot Tagname.Fl(nnn)" where nnn = 1127
e."Box Flag slot Tagname.PVFL
f."!Box.FL(nnnn)" for a box flag that resides in the same box where nnnn = 116,384
g."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the NIM UCN address, xx is the HPM box number, and
nnnn = 14095 (data access limit)
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DI (Digital Input)
mm is the IOP Card number (140)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

LNKDTLIST (SECM)
FF Param. Source:
Type:
String
Lock:
View
Default: Null String
PtRes: IOP
Range: N/A

210

None
IOP Link Staus Detail String Provides additional information about
the link status and is only used for display purposes.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LNKMASRE (SECM)

LNKMASRE (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: N/A

Network Management Information Block: DlmeLinkMasterInfoRecord


Link Master Record This parameter contains IOP stack
information.

LOADFAIL
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
N/A

Node Load Failure Information

LOADFLAG
Type:
Lock:
Default:
PtRes:
Range:

String_2
Load Flag
View
N/A
HPM
Hexadecimal characters 00 to FF

LOADPCKT
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
View
N/A
HPM
N/A

Current Personality Image Packet Being Loaded to This Node

HPM Parameter Reference Dictionary


Honeywell Inc.

211

LOADSCOP (NIM)

LOADSCOP (NIM)
Type:
Lock:
Default:
PtRes:

E:$LOADSCP
PtBld
NIMAndPm
NIM

Load ScopeDefines the scope of the point-build procedure for NIM and
HPM configuration. The point information is loaded to both the NIM and
HPM or to the NIM only. A value of NIMONLY is typically used to
configure points into the NIM only during installation of a new system without
HPMs.

NOTE
When points are built to a NIM and the NIM is restarted with no database, the points need
to be reloaded from checkpoint or the points must be reconfigured. If the database is to
be reconfigured, the HPMM must be in Idle, and the point execution state must be Inactive. This
allows the point build operation to override the database that already exists there.

NOTE
To delete active entities from the HPM database, the point must be put to the inactive state. An
alternative is to delete the entity in the NIM only by changing the LOADSCOP parameter for the NIM
to NimOnly and deleting the point. Be sure to restore LOADSCOP to NimAndPM after deleting points.

Range:

NimOnly (Configured data is to be loaded into the NIM only)


NimAndPm (Configured data is to be loaded into the NIM and HPM)

LOADSTAT
Type:
Lock:
Default:
PtRes:
Range:

212

E:LOADSTAT
View
N/A
HPM
Notload
Loaded
Loading
Unlding

Load Status

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LOBJLIST(1-20) (SECM)

LOBJLIST(1-20) (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP

FBAP VFD
Link Object List This is an arrayed parameter that contains a listing
of the link objects in the IOP FBAP VFD. The last two elements of
this record are used for mapping the fieldbus parameter to/from the
IOP database.
The default value of N/A indicates that the local index and VCR
number are equal to 0 (zero)

Range:

N/A

LOCALMAN (AnalgOut, RegCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Local Manual FlagIndicates whether the associated hardware output of this
point is being controlled by a manually operated analog display.
View
Off
HPM
Off (Output is not being controlled by an Analog Display)
On (Output is being controlled by an Analog Display)

LOCALMAN (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

Local Manual FlagWhen On, indicates that the output(s) is being locally
controlled and not by the HPM. When this flag is on, it usually indicates that the
"hand/off/auto" switch is not in the "auto" position.

LOCUTOFF (AI)
Type:
Lock:
Default:
PtRes:
Range:

Real
Low Signal Cut Off for Flow InputsDefines the low cut-off point for low
inputs.
Eng/PB
NaN
HPM
PVEULO to PVEUHI; >0
Helpful Hint: LOCUTOFF configuration applies only if PVChar = Linear or Sqrroot

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

213

LOCPRIM(1-4)

LOCPRIM(1-4)
Type:
Lock:
Default:
PtRes:

N/A
View
N/A
HPM

Range:

N/A

Local PrimaryReturns the tag name of a primary point in the same HPM that
is storing to this points parameters.
The parameter index indicates the parameter being pushed to by the primary as
follows, depending on the algorithm configured in the Regulatory Control point:
1 = SP or X1
2 = Ratio or X2
3 = X3
4 = X4

Helpful Hint: LOCPRIM returns a null entity ID if the connection is not configured or the primary point
is in a different node (such as, a peer-to-peer connection).

LODSTN(1)(12) (Logic)
Type:

Blind Record Logic Output-Connection DestinationSpecifies up to 12 destinations to


which the current values of the logic slot outputs are supplied. The destinations
in an Array
can be specified using the "Tagname.Parameter" format or the hardware
(1..12)
reference address format. Refer to the HPM Control Functions and Algorithms
Lock:
PtBld
manual for a detailed description.
Default: null.null
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters, and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters, and must be a legitimate parameter name.
Some possible output-connection destinations are
a."DigOut slot tagname.ONPULSE or OFFPULSE"
b."DigOut slot Tagname.SO"
c."Logic slot Tagname.Fl(nn)" where nn = 712
d."ProcMod Tagname.Fl(nnn)" where nnn = 1127
e."Flag slot Tagname.PVFL
f."!Box.FL(nnnn)" for a box flag that resides in the same HPM box where
nnnn = 1-16,384.
g."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the UCN number, xx is the HPM box number of the destination parameter, and nnnn = 1-4095
(data access limit).

214

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LODSTN(1)(2) (DevCtl)

Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DO (Digital Output)
mm is the IOP Card number (1-40)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

LODSTN(1)(2) (DevCtl)
Type:

Blind Record Device Control Output Connection DestinationSpecifies up to 2


in an Array
destinations to which the current values of the Device Control slot outputs are
(1..2)
supplied. The destinations can be specified using the "Tagname.Parameter"
Lock:
PtBld
format or the hardware reference address format Refer to the HPM Control
Default: Null
Functions and Algorithms manual for a detailed description.
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.
Some possible output-connection destinations are
a."DigOut slot tagname.ONPULSE or OFFPULSE"
b."DigOut slot Tagname.SO"
c."Logic slot Tagname.Fl(nn)" where nn = 712
d."ProcMod Tagname.Fl(nnn)" where nnn = 1127
e."Flag slot Tagname.PVFL
f."!Box.FL(nnnn)" for a box flag that resides in the same HPM box where
nnnn = 1-16,384.
g."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the UCN number, xx is the HPM box number of the destination parameter, and nnnn = 1-4095
(data access limit).
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DI (Digital Input)
mm is the IOP Card number (140)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

215

LOENBL(1)(2) (DevCtl)

LOENBL(1)(2) (DevCtl)
Type:

E:$PMDVPRM
in an Array
(1..2)
Lock:
PtBld
Default: FL2
PtRes: HPM
Range:

Device Control Output EnableAllows the respective output


connection defined by LODSTN to write the value of the specified
Device Control parameter to the destination. The logic output is allowed
when the enable function, selected from the list below, is On. If the FL1
parameter is specified and the output data type is logical, output occurs
only during change (normally, it is continuous).

FL1...FL12 [Local flag; either a 1 (On) or a 0 (Off)]


D1, D2 [Digital PV inputs, either a 1 (On) or a 0 (Off)]
SI0 [Safety interlocks, either a 1 (On) or a 0 (Off)]
I0, I1, I2 [Interlocks, either a 1 (On) or a 0 (Off)]
P0, P1, P2 [Permissives, either a 1 (On) or a 0 (Off)]
PISO1..PISO12 [Primary Input Gate Values (logical)]
SISO1..SISO12 [Secondary Input Gate Values (logical)]
PGSO1..PGSO4 [Primary Gate Output Values (logical)]
SGSO1, SGSO2 [Secondary Gate Output Values (logical])
L1..L12 [Logic input value to device control slot (logical)]

LOENBL(1)(12) (Logic)
Type:
Lock:
Default:
PtRes:

E:$PMMLGPM
PtBld
FL2
HPM

Range:

FL1...FL12 [Local flag; either a 1 (On) or a 0 (Off)]


SO1...SO24 [Logic-block output; either a 1 (On) or a 0 (Off]
L1...L12 [Logic input value to logic slot (logical)]

216

Logic Output EnableAllows the respective output connection defined


by LODSTN to write the value of the specified logic-slot parameter to
the destination. The logic output is allowed when the enable function,
selected from the list below, is On. If the FL1 parameter is specified
and the output data type is logical, output occurs only during change
(normally, it is continuous).

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LOGALGID(1)(24) (Logic)

LOGALGID(1)(24) (Logic)
Type:
Lock:
Default:
PtRes:

E:$PMMLGAL
PtBld
NULL
HPM

Range:

Algorithm ID
0-NULL
1-AND
2-OR
3-NOT
4-NAND
5-NOR
6-XOR
7-QOR2
8-QOR3
9-SWITCH
10-EQ
11-NE
12-GT
13-GE
14-LT
15-LE
16-CheckBad
17-Pulse
18-MinPulse
19-MaxPulse
20-Delay
21-OnDly
22-OffDly
23-WatchDog
24-FlipFlop
25-ChDetect
26-DISCREP3

Logic Block Algorithm IdentifierDefines the logic algorithm to be


used for a particular logic block. A different logic algorithm can be
specified for each logic block within a logic slot. Refer to the HPM
Control Functions and Algorithms manual for a detailed description of
each logic algorithm.
Description
Input(s)
No logic algorithm is executed
--AND Gate
*S1, S2, S3
OR Gate
*S1, S2, S3
NOT Gate
S1
NAND Gate
*S1, S2, S3
NOR Gate
*S1, S2, S3
XOR Gate
S1, S2
Qualified OR Gate with 2 Inputs On
S1, S2, S3, S4
Qualified OR Gate with 3 inputs On
S1, S2, S3, S4
Switch
S1, S2, S3
Compare equal with deadband
R1, R2, DEADBAND
Compare not equal with deadband
R1, R2, DEADBAND
Compare > than with deadband
R1, R2, DEADBAND
Compare > than or = with deadband
R1, R2, DEADBAND
Compare < than with deadband
R1, R2, DEADBAND
Compare < than or = with deadband
R1, R2, DEADBAND
Check for Bad
R1
Fixed-size Pulse
S1, DLYTIME
Pulse with minimum time limit
S1, DLYTIME
Pulse with maximum time limit
S1, DLYTIME
Either Direction
S1
Off-On Delay
S1, DLYTIME
On-Off Delay
S1, DLYTIME
Watchdog Timer
FL6
Flip Flop
S1, S2, S3
Change Detect
S1, S2 , S3
Discrepancy Gate with 3 inputs plus delay
S1, S2, S3, DLYTIME

*Inputs S1S3 can be inverted as required

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

217

LOGICSRC (DigComp, DevCtl)

LOGICSRC (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

Ent_Id
Logic SourceSpecifies the tag name of a point, usually a logic slot, that is
controlling the interlock signals.
PtBld
Null
NIM
Tag name can be up to sixteen characters and the permissible character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.

LOGMIX (Logic)
Type:
Lock:
Default:
PtRes:
Range:

E:$LOGMIX Logic MixDefines the number of input connections, logic blocks, and output
connections this logic slot contains.
PtBld
12_24_4
HPM
Input Connections
Number of
Output Connections
LISRC(1)-LISRC(12)
Logic Blocks
LOSRC(1)-LOSRC(12)
12_24_4
12
24
4
12_16_8
12
16
8
12_8_12
12
8
12

LOSRC(1)(2) (DevCtl)
Type:

E:$PMDVPRM
Device Control Output Connection SourceDefines the Device
Control parameter that is to provide its value to the output connection
in an Array
specified by parameter LODSTN(n), Device Control Output Connection
(1..2)
Destination.
Lock:
PtBld
Default: FL1
PtRes: HPM
Range: FL1...FL12 [Local flag; either a 1 (On) or a 0 (Off])
D1, D2 [Digital PV inputs, either a 1 (On) or a 0 (Off)]
SI0 [Safety interlocks, either a 1 (On) or a 0 (Off)]
I0, I1, I2 [Interlocks, either a 1 (On) or a 0 (Off)]
P0, P1, P2 [Permissives, either a 1 (On) or a 0 (Off)]
PISO1..PISO12 [Primary Input Gate Values (logical)]
SISO1..SISO12 [Secondary Input Gate Values (logical)]
PGSO1..PGSO4 [Primary Gate Output Values (logical)]
SGSO1, SGSO2 [Secondary Gate Output Values (logical)]
L1..L12 [Logic input value to device control slot (either logical or real)]
NN1..NN8 [Local numerics (real)]
PINN1..PINN12 [Numeric constant for arithmetic comparisons (real)]
SECVAR [Secondary variable input value (real)]

218

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LOSRC(1)(12) (Logic)

LOSRC(1)(12) (Logic)
Type:
Lock:
Default:
PtRes:
Range:

E:$PMMLGPM
Logic Output Connection SourceDefines the logic-slot parameter
that is to provide its value to the output connection specified by
Eng/PB
parameter
FL1
LODSTN(n), Logic Output Connection Destination.
HPM
FL1...FL12 [Local flag; either a 1 (On) or a 0 (Off)]
SO1...SO24 [Logic block output; logical 1 or 0)]
L1...L12 [Input to the logic slot (logical or real value)]
NN1...NN8 [Local numeric; data type of Real]

LOWERTIM
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A

Lower Output Pulse Time (In Seconds)Indicates the lower output pulse time
in seconds. This value is clamped to MAXPULSE or CYCLETIM, whichever is
lower. If LOWERTIM is smaller than RP*MINPULSE, no pulse is issued.

LOWRDSTN
Type:

Universal
Ent.Prm
Lock:
PtBld
Default: Null
PtRes: HPM
Range: ONPULSE
OFFPULSE

Lower OP Pulse DestinationDefines the destination of the Lower output


pulse. LOWRDSTN must point to parameter ONPULSE or parameter
OFFPULSE of a DigOut point.

LOWRRATE
Type:
Lock:
Default:
PtRes:
Range:

Real
Lower OP Stroke Rate in Percent/Second
Supr
100.0%/sec.
HPM
>0.0 percent/second

LRL (STI)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
NaN
HPM
N/A, NAN

Lower Range LimitIndicates the lower range limit of the PV at the smart
transmitter. This limit is fixed and cannot be changed. Refer to the description
of the STI_EU parameter for the LRL engineering units.

HPM Parameter Reference Dictionary


Honeywell Inc.

219

LRV (STI)

LRV (STI)
Type:
Lock:
Default:
PtRes:

Real
Supr/View
NaN
HPM

Range:

N/A, NaN

Lower Range ValueDefines the lower end of the operating range for the
PVRAW value. User entry for PVEULO is the user-entered engineering-unit
value that corresponds to LRV. Refer to description of the STI_EU parameter
for the LRV engineering units.
This parameter can be changed only when the STI point execution state
PTEXECST is Inactive.

LSEQNUMR
Type:
Lock:
Default:
PtRes:
Range:

Integer
Eng
0
IOP
?

Last Sequence NumberSpecifies the sequence number of the last personality


image file packet received by the IOP.

LSIOLORN(0) - (4) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

Last Hour's I/O Link Fetch/Store OverrunsIndicates the number of


I/O Link access overruns that have been detected in the last hour.
LSIOLORN is set equal to the contents of CRIOLORN, every hour on the hour.

LSPPXORN(0 - 8) (HPM Box)


Type:
Lock:
Default:
PtRes:

Integer
View
0
HPM

Range:

>0

Last Hour's Point Processing Overruns Per CycleIndicates the number of


point processing overruns that have been detected in the last hour.
LSPPXORN is set equal to the contents of parameter CRPPXORN, every hour
on the hour.

LSTWHNER (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

220

Integer
View
0
HPM
>0

Last When ErrorThe CL Fail/Error code masked by the When Error


clause.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

LSUCNORN (HPM Box)

LSUCNORN (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

Last Hour's UCN Access OverrunsLSUCNORN is set equal to the contents


of parameter CRUCNORN, the current hour's UCN Access Overruns, every
hour on the hour.

LVLSTIDX (SECM)
FF Param. Source:
Type:
Real
Lock:
View
Default: 0x18A
PtRes: IOP
Range: 0-65535

R610
11/99

Network Management Information Block


Live List Index This parameter contains the object dictionary index
of the livelist for this fieldbus link. The IOP will read the value for
this parameter directly from the stack during startup.

HPM Parameter Reference Dictionary


Honeywell Inc.

221

M (IncrSum, ORSel, Switch)

-MM (IncrSum, ORSel, Switch)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
2
HPM
2 to 4

Number of Inputs

MAINDAT (DevCtl, DigComp)


Type:
Time
Maintenance Reset Statistics DateThe date and time of the reset of
Lock:
Engr
maintenance statistics that can also be written by the engineer. Statistics can be
Default: Time of Point reset by the operator only when the device is red tagged, while programs can reset
Build
them at any time. Resetting is accomplished by setting the RESETFL to ON.
PtRes: HPM
Range: Time Stamp (DD MMM YY HH:MM:SS)
Helpful Hint: This parameter is reset when the RESETFL parameter = ON.

MAINTOPT (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

222

Logical
Maintenance OptionIndicates if the maintenance statistics option is used.
PtBld
Off
HPM
Off (Maintenance statistics are not available)
On (Maintenance statistics are available)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MANMODFL (RegCtl)

MANMODFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Manual Mode FlagIndicates whether the current mode of the slot is Manual.
View
N/A
HPM
Off (Current mode is other than Manual)
On (Current mode is Manual)

MANOPCMD
Type:
Lock:
Default:
PtRes:
Range:

E:$MANOPCM
Manual Output Pulse CommandDefines the output pulse command
Oper
issued by the operator for raising and lowering the output. See also,
None
MANOPTIM.
HPM
0-None (No change)
1-Raise_1 (Raise output by 1 MANOPTIM each keystroke)
2-Lower_1 (Lower output by 1 MANOPTIM each keystroke)
3-Raise_10 (Raise output by 10 MANOPTIMs each keystroke)
4-Lower_10 (Lower output by 10 MANOPTIMs each keystroke)

MANOPTIM
Type:
Lock:
Default:
PtRes:
Range:

Real
Manual Output Pulse Time (in seconds)Defines the width of the raise or
lower output pulse that is issued by the operator.
Eng/PB
1.0
HPM
0.0 to 60.0 seconds

MASKTIM (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Integer
MasktimeThe amount of time the SECVAR parameter alarms are masked
after a change in the output state.
Supr
0
HPM
0 to 1000 seconds

MAXCNFPU (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
N/A
HPM

Maximum Configurable PUsSpecifies

HPM Parameter Reference Dictionary


Honeywell Inc.

223

MAXPU (ProcMod)

MAXPU (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
0 to

Maximum PUsSpecifies the maximum PUs used for point processing.

MAXPULSE
Type:
Lock:
Default:
PtRes:
Range:

Real
Maximum Pulse Time LimitDefines the maximum pulse time limit. If the
calculated pulse time is greater than this value then a pulse of length
Supr
MAXPULSE is issued.
60
HPM
MINPULSE to 60.0 seconds
NaN

MAXSLOTS
Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
IOP
0 - 127 slots

Maximum Available SlotsReturns the maximum number of slots that can be


configured in an IOP.

Helpful Hint: Applies to the following IOP types: AO16, DI32 and DO32.

MAXTIM0H (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

224

Real
Supr
0
HPM
N/A

Maximum Time Allowed in State 0The maximum amount of time (based on


the PV) in hours allowed for state 0.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MAXTIM1H (DevCtl, DigComp)

MAXTIM1H (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0
HPM
N/A

Maximum Time Allowed in State 1The maximum amount of time (based on


the PV) in hours allowed for state 1.

MAXTIM2H (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0
HPM
N/A

Maximum Time Allowed in State 2The maximum amount of time (based on


the PV) in hours allowed for state 2.

MAXTRAN02 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Time
Maximum Number of Transitions into StateThis is the maximum number
of transitions allowed in each state, and is the target value for maintenance
Supr
statistics.
0.0
HPM
0 (There is no limit)

MDMHWREV (HPM Box, NIM)


Type:
Lock:
Default:
PtRes:
Range:

String_2
View

Modem Hardware Revision

HPM, NIM
Hexadecimal Characters 00 to FF

MEMFWREV
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

String_2
View

Memory Firmware Revision

HPM
Hexadecimal Characters 00 to FF

HPM Parameter Reference Dictionary


Honeywell Inc.

225

MEMHWREV

MEMHWREV
Type:
Lock:
Default:
PtRes:
Range:

String_2
View

Memory Hardware Revision

HPM
Hexadecimal Characters 00 to FF

METADTAF (FBCM)
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

Device Description
Metadata Information for Function Block

METADTAR (PECM)
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

Device Description
Metadata Information for Resource Block

METADTAT (FBCM)
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

Device Description
Metadata Information for Transducer Block

METAENM (PECM, FBCM)


FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

226

Device Description
Metadata Information: Fieldbus Enumerations

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MGCFGCMD(1-10) (SECM)

MGCFGCMD(1-10) (SECM)
FF Param. Source:
Type:
E:$CFGCMD
Lock:
Eng/PB
Default: NULL
PtRes: IOP
Range:

None
Configuration Command This arrayed parameter is used for
handshaking between the TPS Buider and the fieldbus IOP during
clear/load device configuration data sequences. This parameter is
written to by the TPS Builder and read by the IOP.
CAUTION: Writing to this parameter for reasons other than
described will cause IOP/device communications failures.

0-NULL
1-CFG_STRT
2-CFG_DONE
3-CFG_MATCH

MGCFGSTA(1-10) (SECM)
FF Param. Source:
Type:
E:$CFGSTAT
Lock:
View
Default: NULL
PtRes: IOP
Range: 0-NULL
1-CFG_INIT
2-CFG_STRT

None
Configuration Command Status This arrayed parameter shows the
status of a write operation to the CFGCMD parameter. This parameter
is written to by the IOP and read by the TPS Builder.

MGDEVADR(1-10) (SECM)
FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: 0
PtRes: IOP
Range:

Network Management Information Block Related


Management Device Address This arrayed parameter is the this
node parameter of a configured device. The value of this parameter is
used at runtime to match to the proper device on the fieldbus link.
Each element must be written after the its correspoding elements in the
following parameters: MGPDTAG, MGDEVID, MGDEVREV,
MGMODNAM, MGVENAME, and MGVCRIDX.

0x14 0xF7

MGDEVID(1-10) (SECM)
FF Param. Source:
Type:
String
Lock:
PtBld
Default: Null String
PtRes: IOP
Range:

R610
11/99

System Management Information Block Related


Management Device Identifier This arrayed parameter contains the
DEV_ID of a configured device. The value of this parameter is used at
runtime to match to the proper device on the fieldbus link. Each
element must be written before its corresponding element in
MGDEVADR.

N/A

HPM Parameter Reference Dictionary


Honeywell Inc.

227

MGDEVREV(1-10) (SECM)

MGDEVREV(1-10) (SECM)
FF Param. Source:
Type:
String
Lock:
PtBld
Default: Null String
PtRes: IOP
Range:

Management VFD
Management Device Revision This arrayed parameter contains the
Management VFD revision of up to 10 configured devices. The value
of this parameter is used at runtime to match to the proper device on
the fieldbus link. Each element must be written before its
corresponding element in MGDEVADR.

N/A

MGINFIDX (PECM)
FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: 0
PtRes: IOP
Range:

None
Device List Index for the FBAP VFD This parameter contains the
index within the configured device list in the SECM that is associated
with this FBAP VFD (PECM). This parameter must be the last
parameter to be written during a point load.

1-10

MGMODNAM(1-10) (SECM)
FF Param. Source:
Type:
String
Lock:
PtBld
Default: Null String
PtRes: IOP
Range:

Management VFD
Management VFD Model Name This arrayed parameter contains
the management VFD model name for up to 10 configured devices.
This parameter is used at runtime to match to he propoer device on the
link. Each element must be written before its correspoding element in
MGDEVADR.

N/A

MGPDTAG(1-10) (SECM)
FF Param. Source:
Type:
String
Lock:
PtBld
Default: Null String
PtRes: IOP
Range:

228

Device SMIB Related


Management Physical Device Tag This arrayed parameter contains
the management physical device tags for up to 10 configured devices.
This parameter is used at runtime to match to the proper device on the
link. Each element must be written before its correspoding element in
MGDEVADR.

N/A

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MGVCRIDX(1-10) (SECM)

MGVCRIDX(1-10) (SECM)
FF Param. Source:
Type:
Integer
Lock:
PtBld/Engr
Default: 0
PtRes: IOP
Range:

None
Management VCR Index This arrayed parameter contains the VCR
list index (to the management VFD VCR) of up to 10 configured
devices. This parameter is used at runtime to match to the proper
device on the link. Each element must be written before its
correspoding element in MGDEVADR.

1-63

MGVENNAME(1-10) (SECM)
FF Param. Source:
Type:
String
Lock:
PtBld
Default: Null String
PtRes: IOP
Range:

Management VFD
Management VFD Vendor Name This arrayed parameter contains
the management VFD vendor name for up to 10 configured devices.
This parameter is used at runtime to match to the proper device on the
link. Each element must be written before its correspoding element in
MGDEVADR.

N/A

MINPULSE
Type:
Lock:
Default:
PtRes:
Range:

Real
Minimum Pulse Time LimitDefines the minimum pulse time limit for the
Raise pulse. If the calculated pulse time value is smaller than this value, no
Supr
pulse is issued.
0.0
HPM
0.0 seconds to MAXPULSE
NaN

MINUTE (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
View
N/A
HPM
0 to 59

Current MinuteValue of the LCN time in the HPM.

HPM Parameter Reference Dictionary


Honeywell Inc.

229

MISC

MISC
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

None
Miscellaneous This parameter set has been added for compatibility
with fieldbus requirements.

MNFASIC (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 31

HPMM Communications Control Card ASIC Revision

MNFCCDAY (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 31

HPMM Communications Control Card Manufacturing Date-Day

MNFCCINF (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_8
View
0
HPM

HPMM Communications Control Card Manufacturing Information

MNFCCMTH (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

230

Integer
View
0
HPM
1 - 12

HPMM Communications Control Card Manufacturing Date-Month

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MNFCCSER (HPM Box)

MNFCCSER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_24
View
0
HPM

HPMM Communications Control Card Serial Number

MNFCCYR (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 99

HPMM Communications Control Card Manufacturing Date-Year

MNFFPGA (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 31

HPMM I/O Link Card FPGA Revision

MNFIODAY (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 31

HPMM I/O Link Card Manufacturing Date- Day

MNFIOINF (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

String_8
View
Blank
HPM
0 - 99

HPMM IO Link Processor Card Manufacturing Information

HPM Parameter Reference Dictionary


Honeywell Inc.

231

MNFIOMTH (HPM Box)

MNFIOMTH (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 12

HPMM IO Link Card Manufacturing Date-Month

MNFIOSER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_24
View
0
HPM

HPMM IO Link Card Serial Number

MNFIOYR (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
0 - 99

HPMM IO Link Card Manufacturing Date-Year

MNFMDDAY (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 31

HPMM UCN Interface Card Manufacturing Date-Day

MNFMDINF (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

232

String_8
View
Blank
HPM

HPMM UCN Interface Card Manufacturing Information

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MNFMDMTH (HPM Box)

MNFMDMTH (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
1 - 12

HPMM UCN Interface Card Manufacturing Date-Month

MNFMDSER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_24
View
0
HPM
N/A

HPMM UCN Interface Card Serial Number

MNFMDYR (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
0 - 99

HPMM UCN Interface Card Manufacturing Date-Year

MODATTR
Type:
Lock:
Default:
PtRes:

E:MODATTR
Oper
Operator
HPM

Range:

0-Operator (Operator can set Mode, OP, SP, Ratio, Bias)


1-Program (Program can set Mode, OP, SP, Ratio, Bias)
2-Normal
3-None (No mode attribute)

Mode AttributeDefines whether the operator or the sequence program has


the authority to change certain parameters of this data point. At the Universal
Station, the mode attribute is displayed next to the mode of the data point. If
the mode attribute is Program, a -P appears to the left of MODE. If the
attribute is operator, blanks are displayed to the left of mode.

Helpful Hint: MODATTR change requires SHUTDOWN = Off and REDTAG = Off. When
the "normal mode" button on the Operator's keyboard is pressed, MODATTR =
NMODATTR unless NMODATTR = None.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

233

MODATTR (FBCM)

MODATTR (FBCM)
FF Param. Source:
None
Type:
E:MODATTR Mode AttributeDefines whether the operator or the sequence
program has authority to change certain parameters of this data point.
Lock:
Oper
Default: Operator
PtRes: IOP
Range: 0- NONE - No mode attribute
1-OPERATOR - Operator can change mode (MODE_BLK.Target), output value (OUT),and
setpoint (SP)
2PROGRAM - Program can change the mode (MODE_BLK.Target), output value (OUT), and
setpoint SP)
3-NORMAL The value that has been specified by the NMODATTR parameter

MODE (AnalgOut)
Type:
Lock:
Default:
PtRes:
Range:

E:MODE
ModeDefines the current mode of the data point. Parameter MODATTR
determines whether operator or the sequence program provides the output value
Oper
for this point. If PNTFORM is Component, then MODE parameter is not
Man
applicable for this data point.
HPM
1-Man
(Operator or Program provides the point's output value (OP))
2-Cas
(Data point receives its output value from a primary data point.
If RCASOPT is DDC, data point receives its output value from an AM point.)
5-Normal (Parameter NMODE determines this point's mode)
Helpful Hint: 1. MODE change by a program requires MODATTR = Program and
REDTAG = Off.
2. MODE change by an operator requires MODATTR = Operator,
MODEPERM = Permit, and REDTAG = Off.

MODE (DigComp, DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

E:MODE
Mode of Digital Composite and Device Control SlotDefines the current
mode of the data point. Parameter MODATTR determines whether operator or
Oper
the sequence program provides the output value for this point. If PNTFORM is
Man
Component, then MODE parameter is not applicable for this data point.
HPM
1-Man
(Operator or Program controls slot's output (OP))
5-Normal (Parameter NMODE contains slot's mode)
Helpful Hint: 1. MODE change by a program requires MODATTR = Program,
SHUTDOWN = Off, and REDTAG = Off.
2. MODE change by an operator requires MODATTR = Operator,
MODEPERM = Permit, SHUTDOWN = Off, and REDTAG = Off.

234

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MODE (RegCtl)

MODE (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:MODE
Mode of Regulatory Control SlotDefines the mode of the RegCtl point.
Oper
Man
HPM
1-Man
(Operator or discontinuous program controls slot's output (OP), regardless of any
automatic control strategy)
2-Cas
(Upstream slot's OP is this slot's SP)
3-Auto
(OP value is computed by the configured RegCtl algorithm, and the setpoint (SP)
comes from the local setpoint (LSP) location in the RegCtl point. An operator or a
discontinuous program can change the setpoint value.
4-Bcas
(Local cascade mode where the RegCtl point receives its setpoint from the OP of a
primary data point, even though the entry for the RCASOPT parameter is Spc,
DdcRsp, or Rsp (where the AM provides the setpoint). In this way, should the AM
or the NIM fail, the control strategy will shed to the local cascade mode.)
5-Normal (Parameter NMODE determines the normal mode of this slot)
Helpful Hint: 1. MODE change by a program requires MODATTR = Program
and REDTAG = Off.
2. MODE change by an operator requires MODATTR = Operator,
MODEPERM = Permit, and REDTAG = Off.

MODE (PECM, FBCM)


FF Param. Source:
MODE_BLK.Actual (Read); MODE_BLK.Target (Write)
Type:
E:$FFMODE ModeDefines the current mode of the resource or function block (CM points).
A write to this parameter will write to the target mode.
Lock:
Oper
Default: None
PtRes: IOP
Range: 0 Man (Manual)
1 Auto (Automatic)
2 Cas (Cascade)
3 Bcas (Backup Cascade)
4 Normal
5 None
6 LM (Loop Manual)
7 IM (Initialization Manual)
11 Rcas (Remote Cascade)
12 Rout (Remote Output)
13 LO (Local Output)
14 OOS (Out of Service)
15 SPARE15 (Not Used)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

235

MODEAPPL(1)(4) (DevCtl, DigComp, RegCtl)

MODEAPPL(1)(4) (DevCtl, DigComp, RegCtl)


Type:
Logical
Lock:
View
Default: Man=On
MODEAPPL [Auto]=Off
MODEAPPL [Bcas]=Off
MODEAPPL[Cas]=Off
Static for DevCtl
and Digcomp points
PtRes: HPM
Range: N/A

Mode ApplicabilityDefines changes for Regulatory Control


points:
MODEAPPL[1] = ON if MAN mode if valid, else it is OFF
MODEAPPL[2] = ON if AUTO mode is valid, else it is OFF
MODEAPPL[3] = ON if CAS mode is valid, else it is OFF
MODEAPPL[4] = ON if BCAS mode is valid, else it is OFF

MODEAPPL (1-16) (PECM, FBCM)


FF Param. Source:
Type:
Logical
Lock:
View
Default: All OFF
PtRes: IOP

Range:

236

MODE_BLK.Permitted
Mode Applicability This is an arrayed parameter that defines valid mode changes for
resource and function blocks (CM points):
MODEAPPL[1] = ON if Man mode is valid, else it is OFF (For PECM, always OFF)
MODEAPPL[2] = ON if Auto mode is valid, else it is OFF
MODEAPPL[3] = ON if Cas mode is valid, else it is OFF (For PECM, always OFF)
MODEAPPL[4] = ON if BCas mode is valid, else it is OFF
MODEAPPL[5] = ON if Normal mode is valid, else it is OFF
MODEAPPL[6] = OFF always
MODEAPPL[7] = OFF always
MODEAPPL[8] = OFF always
MODEAPPL[9] = OFF always
MODEAPPL[10] = OFF always
MODEAPPL[11] = OFF always
MODEAPPL[12] = ON if RCas mode is valid, else it is OFF (For PECM, always OFF)
MODEAPPL[13] = ON if ROut mode is valid, else it is OFF (For PECM, always OFF)
MODEAPPL[14] = OFF always
MODEAPPL[15] = ON if OOS mode is valid, else it is OFF
MODEAPPL[16] = OFF always

0-OFF, 1-ON

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MODEBLKC (PECM, FBCM)

MODEBLKC (PECM, FBCM)


FF Param. Source:
MODE_BLK.Actual + MODE_BLK.Target
Type:
String_8
Combination Mode Defines the combined state of the actual and
target modes (CM points).
Lock:
View
Default: None
PtRes: IOP
Range: Actual mode and target mode are both the same mode.
Actual mode and target mode are not the same mode.

MODEPERM (AO)
Type:
Lock:
Default:
PtRes:
Range:

E:MODEPERM
Mode PermissiveDetermines whether the operator can change the mode
of this data point.
Eng/PB
Permit
HPM
0-Permit (Operator can change this point's mode)
1-NotPerm (Operator cannot change this point's mode)

MODEPERM (DevCtl, DigComp, RegCtl)


Type:
Lock:
Default:
PtRes:
Range:

E:MODEPERM
Mode PermissiveDetermines whether the operator can change the mode
of this data point.
Eng
Permit
HPM
0-Permit (Operator can change this point's mode)
1-NotPerm (Operator cannot change this point's mode)

MODEPERM (FBCM)
FF Param. Source:
None
E:MODEPERM Mode PermissiveDetermines whether operator can change the mode
Type:
of this data point.
Lock:
Engr
Default: Permit
PtRes: IOP
Range: 0-PERMIT (Operator can set this points mode)
1-NOTPERMIT (Operator cannot set this points mode)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

237

MODNAME (SECM, PECM)

MODNAME (SECM, PECM)


FF Param. Source:
Type:
String
Lock:
PtBld/Engr
Default: SECM = "R600
FBUS IOP".
PECM = Null
PtRes: IOP
Range: N/A

VFD Model Number


Model Name of VFD For a SECM, it is the IOP Device Model
Name (which is not in the checkpoint). For a PECM, it is the FBAP
VFD Information (which is in the checkpoint). Used for FBAP
matching and display.

MODNUM
FF Param. Source:
None
Type:
Integer
HPMM/IOP Module NumberDefines the module number in the HPM. The
HPMM is module number 0; the IOP Cards are module numbers 140.
Lock:
PtBld
Default: N/A
PtRes: NIM
Range: 0 to 40 (0 is reserved for the HPMM)

MOMSTATE (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

238

E:$MOMSTAT
Momentary Output StatesDefines which of the output states are
momentary. Refer to the HPM Control Functions and Algorithms manual for
Eng/PB
a detailed description.
None
HPM
0-None (No momentary output states)
1-Mom_1 (State 1 is momentary if NOSTATES = 2 or 3)
2-Mom_0 (State 0 is momentary if NOSTATES = 2)
3-Mom_2 (State 2 is momentary if NOSTATES = 3)
4-Mom_1_2 (State 1 and State 2 are momentary; valid if NOSTATES = 3)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

MONPER (HPM Box)

MONPER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
Monitoring PeriodSpecifies the monitoring period in seconds.
Eng
3600
HPM
4 - 3600 (must be in multiples of 4 seconds)

MONTH (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
Current MonthThe value of the LCN date in the HPM.
View
N/A
HPM
1 to 12 (January to December)

MOVPVFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
Moving PV FlagIndicates whether the PV is moving from one state to another
View
state.
Off
HPM
Off (PV is not moving)
On (PV is moving)

MOVPVTXT (HPM Box, DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:

String_8
PtBld
MOVING
NIM

Moving PV Text DescriptorDefines the state descriptor that is displayed


when the Digital Composite or Device Control point is changing states (moving
from one state to another), or is in-between states. This descriptor, defined on
the HPM box point, is displayed for all digital composite or device control points
in this HPM box if PVTXTOP, defined on the Digital Composite or Device
Control point, = OFF. This parameter contains the text for a configured moving
PV on a per point basis if the PVTXTOPT is ON.

Range:

The permissible character set for the up to eight-character descriptor is as follows:


Alphabetics A-Z (uppercase only)
Numerics 0-9,
Underscore (_)

MPCFWREV (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:
R610
11/99

String_2
View
Blank
HPM

HPMM Master Processor Card Firmware Revision

HPM Parameter Reference Dictionary


Honeywell Inc.

239

MPCHWREV (HPM Box)

MPCHWREV (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

String_2
View
Blank
HPM

HPMM Master Processor Card Hardware Revision

MSGPEND (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
None
HPM
N/A

Sequence Message PendingIndicates that a confirmable sequence message


requiring confirmation has been issued to the operator.

MSGTXT(0)(15) (NIM)
Type:

String_8
in an Array
(0..15)
Lock:
PtBld
Default: Blank
PtRes: NIM
Range: 0 to 15

Status Message TextIndicates the text for the self-defined enumeration of


STSMSG. MSGTXT(0) is always NONE, and cannot be configured. Refer to
Status Messages in the Control Functions and Algorithms Manual for more
information.

MXRMPDEV (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
NaN
HPM
> 0.0,
NaN

Maximum Ramp Deviation ValueIf the PV falls behind the SP during a


ramp segment by more than the value of MXRMPDEV, the ramping action is
stopped until the PV reaches the SP.

MXSOKDEV (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

240

Real
Supr
NaN
HPM
> 0.0,
NaN

Maximum Soak Deviation ValueIf the PV falls behind the SP during a soak
segment by more than the value of MXSOKDEV, the soak timer is stopped until
the PV reaches SP.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

N (Calcultr)

-NN (Calcultr)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
1
HPM
1 to 6

Number of InputsDefines the number of inputs to this algorithm.

N (HiLoAvg, Summer)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
2
HPM
2 to 6 inputs

Number of InputsDefines the number of inputs to this algorithm.

NAME
FF Param. Source:
Type:
String_16
Lock:
PtBld
Default: Blank
PtRes: NIM

None
Point NameIdentifies this point to the system and on displays, reports, and
logs. Figure N-1 shows examples of the Group and Detail Displays on which the
point name appears.
Digital Input, Digital Output, Analog Output, Flag, and Numeric-type data points
do not have to be configured by using the point builder (DEB or TPS Builder)
when you are using hardware reference connections. All other types of data
points have to be configured by using the DEB or TPS Builder and require that a
point name be specified during the point build process.

Range:

R610
11/99

Point name can be up to 16 characters, and the permissible character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric point name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive underscores are
not allowed.
Embedded space characters are not allowed.

HPM Parameter Reference Dictionary


Honeywell Inc.

241

NAME

GROUP DISPLAY

POINT NAME

F 3HP
FC1T1
LBS/SEC
REFLUX

E. U. DESCRIPTOR
KEYWORD

5.7
5.9U
25.9
DETH REFLUX PUMP - A CONTR

POINT DESCRIPTOR

DETAIL DISPLAY
POINT NAME

POINT DESCRIPTOR

FC1T1

DETH REFLUX PUMP A CONTR

UNIT ID

UNIT

XX

.% 75% 5% 25% % -

POINT NAME
F
3HP
FC1T1
LBS/SEC
REFLUX

SP
PV
OUT %

E. U. DESCRIPTOR
KEYWORD

5.7
5.9U
25.9
MAN

Figure N-1 Locations of Terms on Group and Detail Displays

242

HPM Parameter Reference Dictionary


Honeywell Inc.

1850

R610
11/99

NARRSLOT (HPM Box)

NARRSLOT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 500

Number of Array Slots in an HPM

NBSCHOBJ (SECM)
FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: 0
PtRes: IOP

System Management Information Block Related


Number of Scheduled Objects Defines the number of entries in the
fieldbus schedule. This parameter must be written before the
FBSCHVER parameter.

Range: 0 - 20

NCTLSLOT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 250

Number of Regulatory Control Slots in an HPMRefer to the HPM Control


Functions and Algorithms manual for a detailed description of HPM processing
capacity.

NDCSLOT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 999

Number of Digital Composite Slots in an HPMRefer to the HPM Control


Functions and Algorithms manual for a detailed description of HPM processing
capacity.

NDEVSLOT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
PtBld
0
HPM
0 to 400

Number of Device Control Points ConfiguredThe number of Device


Control points in an HPM Box point. Refer to the HPM Control Functions and
Algorithms manual for a detailed description of HPM processing capacity.

HPM Parameter Reference Dictionary


Honeywell Inc.

243

NEIPRQU (NIM PSDP)

NEIPRQU (NIM PSDP)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
NIM
N/A

Number of Event Initiated Processing RequestsThe number of Event


Initiated Processing requests sent in the last 15 seconds.

NEVTAVG (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of Events per SecondAverage number of events


generated by the HPM per second.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NEVTMAX (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Maximum number of Events per SecondMaximum number of events


generated by the HPM per second.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NFASTCTL (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
Number of Fast Regulatory Control SlotsFast slots are processed four times
per second.
PtBld
0
HPM
0 to 100, cannot exceed NCTLSLOT

NFASTDC (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

244

Integer
Number of Fast Digital Composite SlotsFast slots are processed four times
per second.
PtBld
0
HPM
0 to 999, cannot exceed NDCSLOT

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NFASTDEV (HPM Box)

NFASTDEV (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
Number of Fast Device Control Points ConfiguredThe number of fast
device control points in an HPM Box data point. Fast slots are processed four
PtBld
times per second.
0
HPM
0 to 100, cannot exceed NDEVSLOT

NFASTLOG (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
Number of Fast Logic SlotsFast slots are processed four times per second.
PtBld
0
HPM
0 to 100, cannot exceed NLOGSLOT

NFASTPV (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
Number of Fast Regulatory PV slotsFast slots are processed four times per
second.
PtBld
0
HPM
0 to 100, cannot exceed NPVSLOT

NFLAG (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
16, 384
HPM
16,384

Number of Flags in HPM Box Data PointThe HPM always provides 16, 384
box flag variables.

NFLAG (Array)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
Number of Flags in Array Point FL ArrayDefines the number of mapped
PtBld
flags from either the HPM box (EXTDATA`=IO_FL) or a serial interface IOP0
connected device (EXTDATA=IO_FL).
HPM
0 to 512 (When EXTDATA = IO_FL)
0 to 1023 (When EXTDATA `=IO_FL)

HPM Parameter Reference Dictionary


Honeywell Inc.

245

NI02 (DevCtl, DigComp)

NI02 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Inverted Interlocks ValueThe negative value of the corresponding interlock.
Engr
On
HPM
On (Interlock inactive)
Off (Interlock active)
Helpful Hint: This parameter can be changed by the engineer only if the point is inactive
or if the HPM is idle.

NIMREV (NIM)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
NIM
N/A

Revision Number of the NIM Personality

Helpful Hint: This parameter is accessed using $NTWRKuu.NIMREV (where uu = UCN Network
number).

NIMVERS (NIM)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
NIM
N/A

Version Number of the NIM Personality

Helpful Hint: This parameter is accessed using $NTWRKuu.NIMVERS (where uu = UCN Network
number).

NLFM
Type:
Lock:
Default:
PtRes:
Range:

246

Integer
Supr
1
HPM
0 or 1

Nonlinearity FormDefines the form of the nonlinear gain.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NLGAIN (Pid)

NLGAIN (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
0.0 to 240.0

Nonlinear GainDefines the value of the nonlinear gain factor KNL.

NLOC (VdtLdLag)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Eng
30
HPM
2 to 30

Number of Locations in Delay Table

NLOGSLOT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 400

Number of Logic Slots in the HPMRefer to the HPM Control Functions and
Algorithms manual for a detailed description of HPM processing capacity.

NMIN (HiLoAvg)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
Minimum Number of Good InputsDefines the minimum number of valid
inputs (PV status is good or uncertain) to this algorithm.
Supr
1
HPM
1 to N (N is the number of inputs selected by N parameter)

HPM Parameter Reference Dictionary


Honeywell Inc.

247

NMODATTR (RegCtl)

NMODATTR (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:MODATTR Normal Mode AttributeDefines whether an operator or a program can


change certain parameters such as the mode, SP, or OP of a data point when
Engr
the point is in the normal mode.
None
HPM
0-Operator (Operator has control of the point)
1-Program (Program has control of the point)
2-Normal
3-None (MODATTR is not affected by this parameter)
Helpful Hint: If NMODATTR = Operator or Program and the "normal mode" button on the
Operator's keyboard is pressed, MODATTR = NMODATTR. If NMODATTR
is to be changed, the engineer must change it.

NMODATTR (FBCM)
FF Param. Source:
None
Type:
E:MODATTR Normal Mode AttributeDefines whether the operator or the
Lock:
Engr
sequence program has the authority to change certain parameters of a
point when the a point is in its normal mode.
Default: None
PtRes: IOP
Range: 0-Operator (Operator has control of the point)
1-Program (Program has control of the point)
2-Normal
3-None (MODATTR is not affected by this parameter)
Helpful Hint: If NMODATTR = Operator or Program and the "normal mode" button on the
Operator's keyboard is pressed, MODATTR = NMODATTR. If NMODATTR
is to be changed, the engineer must change it.

NMODE (AnalgOut)
Type:
Lock:
Default:
PtRes:

E:MODE
Engr/PB
None
HPM

Range:

0-None (No configured "normal" operating mode)


1-Man (Manual is configured "normal" mode)
2-Cas (Cascade is configured "normal" mode)

Normal ModeAllows user to define the normal mode for this data point.

Helpful Hint: NMODE configuration for the Cas option requires RCASOPT = Ddc.

248

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NMODE (DevCtl, DigComp)

NMODE (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Normal ModeAllows user to define the normal mode for this data point.
E:MODE
View
Man
HPM
1-Man (Manual is the "normal" operating mode)

NMODE (FBCM,PECM)
FF Param. Source:
MODE_BLK.Normal
Type:
E:$FFMODE Normal ModeDefines the normal mode of the resource or function block (CM
points).
Lock:
Engr
Default: None
PtRes: IOP
Range: 0 Man (Manual)
1 Auto (Automatic)
2 Cas (Cascade)
3 Bcas (Backup Cascade)
4 Normal
5 None
6 LM (Loop Manual)
7 IM (Initialization Manual)
11 Rcas (Remote Cascade)
12 Rout (Remote Output)
13 LO (Local Output)
14 OOS (Out of Service)
15 SPARE15 (Not Used)

NMODE (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Normal ModeAllows user to define the normal mode for this data point.
E:MODE
Engr
None
HPM
0-None (No configured "normal" operating mode)
1-Man (Manual is the "normal" operating mode)
2-Cas (Cascade is the "normal" operating mode)
3-Auto (Automatic is the "normal" operating mode)
4-Bcas (Backup Cascade is the "normal" operating mode)
Helpful Hint: Mode. If NMODATTR = None and the "normal mode" button on the Operators
keyboard is pressed, MODE is set to the contents of NMODE.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

249

NMODETRK (HPM Box)

NMODETRK (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$NMODETR Normal Mode Tracking Suppression Enable/disable Normal Mode and


PtBld
Normal Mode attribute from tracking mode and mode attribute changes.
Enable
HPM
Enable
Disable

NMSGTXT (NIM)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
NIM
0 to 15

Number of Message Text ItemsDefines the number of message text items


that you can enter. See MSGTXT.

NN(i) (Array)
Type:
Lock:

Real
Array Point Numeric VariablesNumerics are mapped from either the HPM
Determined by box (defined by NNUMERIC and NNSTIX parameters) or from a serial
SPLOCK
interface IOP-connected device (when EXTDATA=IO_NN, mapping is defined
parameter
by the IOPNUM, FTANUM, DEVADDR, NNSTIX, and NNUMERIC
Default: N/A
parameters).
PtRes: HPM
Range: 1 i Array parameter NNUMERIC

NN(1)(8) (DevCtl, Logic)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
NaN
HPM
N/A

Numerics 1-8Eight numerics are provided with each device control and logic
slot. The numerics can be used as reference values for the comparison logic
algorithms, or they can be used as source parameters for the output connections
when writing predefined analog constants to other points. The values of the
numerics can be changed from the Universal Station, by other device control
logic slots, or by user-written programs.

NN(1)(80) (ProcMod)
Type:
Lock:

Real
Determined
by SPLOCK
parameter
Default: NaN
PtRes: HPM
Range: N/A

250

Numeric VariablesEach process module in the HPM has 80 numerics that


can be used for implementing batch operations.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NN(1)(16,384) (HPM Box)

NN(1)(16,384) (HPM Box)


Type:
Lock:
Default:
PtRes:

Real
Oper
NaN
HPM

Range:

N/A

Numeric ValueThis is an array of up to 16,384 numeric variables. The upper


bound of this array is determined by the NNUMERIC parameter. Numerics
NN(1) to NN (2047) are taggable. Numerics NN(1) to NN (4095) are accessible
from the LCN by using hardware form [!Box.NN( )]. Numerics 4096 through
16,384 are accessible only through Array points.

NNDESC (Array)
Type:
Lock:
Default:
PtRes:
Range:

String_64
PtBld
Spaces
HPM
N/A

NN Array DescriptorDescribes NN data for the Array point.

NNINSET(1)(10) (DevCtl)
Type:

Integer
in an Array
(1..10)
Lock:
Supr
Default: 0
PtRes: HPM
Range: 0 to 32767

Numeric 1 - 10A set of 10 integers that are used by the primary input gate
IN_SET algorithm.

NNSTIX (Array)
Type:
Lock:
Default:
PtRes:
Range:

Real
Numeric Array Start IndexDefines the start index in Box NN variables, or a
serial interface-connected device.
PtBld
0
HPM
0 to 99,999 (When EXTDATA=IO_NN, 0 can be valid device index)
0 to Box parameter NNUMERIC (When EXTDATA`IO_NN, 0 indicates no numerics are
configured)

NNUMERIC (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
PtBld
0
HPM
0 to 16,384

Number of Numerics in HPM Box Data PointThe number of box numerics


is determined in intervals of 16 numerics.

HPM Parameter Reference Dictionary


Honeywell Inc.

251

NNUMERIC (Array)

NNUMERIC (Array)
Type:
Lock:
Default:
PtRes:

Integer
PtBld
0
HPM

Range:

0 - 16 (Floats), 0 - 32 (Integers), 0 - 64 (Byte Integers) When EXTDATA = IO_NN


0 to 240 When EXTDATA `=IO_NN

Number of Numerics in Array Point NN ArrayDefines the number of


numerics mapped from either the HPM box (EXTDATA`=IO_NN), or a serial
interface IOP-connected device (EXTDATA=IO_NN). For external data, the
valid range depends on how numeric data is organized in the device.

NOASOC (PECM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: IOP
Range: 0 - 32

None
Number of Associated FBCMsThis parameter shows the number of
FBCMs associated with this PECM.

NOCINPTS (RegCtl)
Type:
Integer
Lock:
PtBld
Default: Based on
CTLALGID,
CTLEQN, M
PtRes: HPM
Range: 0 to 4

Number of Control Input ConnectionsDefines the number of control input


connections for this algorithm.

NOCOPTS (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
1
HPM
0 to 4

Number of Control Output ConnectionsDefines the number of control


output connections from this RegCtl point.

Helpful Hint: Control output engineering ranges (CVEULO, CVEUHI) must be entered
for CTLALGID = PidErfb and Rampsoak, and must be entered for
CTLALGID = Pid, PidFf, and RatioCtl when NOCOPTS = 0. For
CTLALGID = Pid, PidFf, and RatioCtl, with NOCOPTS > 0, the CV
ranges are obtained from a secondary output connection.

252

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NODEASSN (HPM Box)

NODEASSN (HPM Box)


Type:
E:$NODEAS
N
Lock:
Default:
PtRes:
Range:

Node AssignmentDefines whether the NIM on this logical UCN or a NIM


on another logical UCN is the primary NIM for this UCN node.

PtBld
ThisNIM
NIM
ThisNIM (The NIM on this logical UCN is responsible for parameter fetch/stores,
alarming, AM control strategy and checkpointing for this UCN node.)
RemotNIM (A NIM on another logical UCN is responsible for configuring, checkpointing, and
restoring the database through this UCN node.)

NODECMD (HPM Box)


Type:
Lock:
Default:
PtRes:

E: $PMCMD
Eng
None
HPM

Range:

0-None (No request made to the HPM)


1-Run (HPM requested to go to the Run state)
2-Idle (HPM requested to go to an Idle state)
3-Warmstrt (Warm Start requested )
4-Coldstrt (Cold Start requested )
5-Pause (HPM requested to go to the Simul_Pause state)
6-Resume (HPM requested to go to the Simul_Run state)

Node CommandDefines the command issued to the HPM.

NODECONF (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$PMCONF Node Configuration for the HPMCurrently not used. This parameter must
always be set to manual.
View
Manual
HPM
Manual
Auto

HPM Parameter Reference Dictionary


Honeywell Inc.

253

NODENUM (NIM)

NODENUM (NIM)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
N/A
NIM
1 to 64

Node NumberDefines the address of the NIM on the UCN.

Note
The node number assigned to the NIM should be the lowest node number on the UCN (see Timesync).

NODENUM (FBCM, HPM Box, PECM, SECM)


FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: N/A
PtRes: NIM
Range: 1 to 64

None
Node NumberDefines the address of the HPMs on the UCN. NODENUM
assigned for any HPM must be odd whether PKGOPT equals
Option 1 (nonredundant) or Option 2 (redundant). Because of this restriction
and because the NIM takes up one odd address and the next even address, the
maximum number of HPM's that can be on the UCN is 31. The primary HPMM
is assigned an odd address, the associated secondary (redundant) HPMM is
assigned the next (even) address.

NODEOPER
Type:
Lock:
Default:
PtRes:
Range:

E:$PRIMSEC Node Operating Mode


View
NIM
Primary (HPM/NIM is the acting primary node)
Secndry (HPM/NIM is the acting secondary)

NODESC (Logic)
Type:
Lock:
Default:
PtRes:
Range:

254

Integer
PTBLD
0
NIM
0 to 12

Number of Generic DescriptorsDefines the number of user-defined generic


descriptors that are to be used on this logic slot. For each descriptor, the
parameter in the logic slot to which the generic descriptor is attached is defined
by the PRMDESC(n) parameter, and the corresponding descriptors are defined
by the GENDESC(n) parameters. This allows the user to customize the
descriptors used for displaying the logic slot on the Universal Station displays.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NODESTAT (HPM Box)

NODESTAT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$NODESTA HPM Node Status


View
N/A
HPM
OffNet (HPM is not running on UCN)
OK (HPM is configured and running)

NODESTAT (NIM)
Type:
Lock:
Default:
PtRes:
Range:

E:$NODESTA NIM's Node Status


View
N/A
NIM
OffNet (NIM is not running on UCN)
OK (NIM is configured and running)

NODESTS (NIM)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$DSPSTAT
NIM Node Summary StatusIndicates the current overall status of the NIM.
View
N/A
NIM
OffNet (NIM cannot communicate with HPMM)
OK (NIM is performing normally)

HPM Parameter Reference Dictionary


Honeywell Inc.

255

NODESTS (HPM Box)

NODESTS (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$DSPSTAT
HPM Node Summary StatusIndicates the current overall status of the
HPM on the UCN.
View
N/A
HPM
0-OK (HPM is performing normally)
1-IOIDL (At least one IOP has entered the idle state)
2-IDLE (HPMM has entered the idle state)
3-PF_IOIDL (Partial failure in one or more idle IOPs)
4-PF_IDLE (Partial failure in HPMM that is in idle state)
5-PartFail (Partial failure in HPMM that is in run state)
6-Fail (HPMM has sent a "failed" message to the NIM)
7-Alive (No event reports or point processing)
8-Loading (HPMM's personality or database is loading)
9-PowerOn (Transitional state when power applied to HPMM)
10-OffNet (NIM cannot communicate with HPMM)
12-NotConf (HPMM cannot be found on the UCN)
13-ConfgMis (IOP mismatch in NIM Box point)
19-Standby
20-S_OK (OK in I/O simulation mode)
21-S_IOIDL (IOIDL in I/O simulation mode)
22-S_IDLE (IDLE in I/O simulation mode)
23-S_PFIOIL (PF_IOIDL in I/O simulation mode)
24-S_PFIDLE (PF_IDLE in I/O simulation mode)
25-S_PtFail (PartFail in I/O simulation mode)
26-S_Pause (HPM is in the simulation pause state)
27-StandbySF
28-Upgrade
29-UpgradeSF

Helpful Hint: Loading the HPMM's operating personality requires NODESTS = Alive.

NODETYP (NIM)
Type:
Lock:
Default:
PtRes:
Range:

256

E:$UCNNDTY
UCN Node TypeDefines the node type of this UCN node.
PtBld
NIM
NIM
NIM (Network Interface Module)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NODETYP (HPM Box)

NODETYP (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$UCNNDTY
UCN Node TypeDefines the node type of this UCN node.
PtBld
HPM
NIM
HPM (High-Performance Process Manager)

NODETYP (HPM Points)


FF Param. Source:
None
Type:
E:$UCNNDTY UCN Node TypeDefines which node type supports this point.
Lock:
PtBld
Default: HPM
PtRes: NIM
Range: HPM (High-Performance Process Manager)

NODFSTAT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$NODFSTA Node's Functional StatusDefines the status of the UCN node.


Supr
Basic
NIM
Full (All LCN devices can read/write from/to this node)
Basic (AM and CM cannot write to this node)

NODINPTS (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
Number of Digital InputsDefines the number of digital input connections to
this data point.
PtBld
1
HPM
0 (No inputs)
1 (One input)
2 (Two inputs)

HPM Parameter Reference Dictionary


Honeywell Inc.

257

NODOPTS (DevCtl, DigComp)

NODOPTS (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Integer
Number of Digital OutputsDefines the number of digital output connections
from this data point.
PtBld
1
HPM
0 (No outputs)
1 (One output)
2 (Two outputs)
3 (Three outputs)

NOGINPTS (RegPV, RegCtl)


Type:
Lock:
Default:
PtRes: HPM
Range: 0 - 4

Number of General Input Connections

Helpful Hint: NOGINPTS + NOGOPTS cannot exceed four.

258

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NOGOPTS (RegPV, RegCtl)

NOGOPTS (RegPV, RegCtl)


Type:
Lock:
Default:
PtRes: HPM
Range: 0 - 4

Number of General Ouptut Connections

Helpful Hint: NOGINPTS + NOGOPTS cannot exceed four.

NOLINPTS (DevCtl, Logic)


Type:
Lock:

Integer
View (Logic),
PtBld

Number of Logic InputsIndicates the number of logic inputs to this logic or


Device Control slot.

(DevCtl)
Default: 12 (Logic)
0 (DevCtl)
PtRes: HPM
Range: 0 to 12

NOLOGBLK (Logic)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 to 24

Number of Logic BlocksIndicates the number of logic blocks that have been
configured for a particular logic slot.

NOLOPTS (DevCtl, Logic)


Type:
Lock:

Integer
View (Logic)
PtBld

Number of Logic Output ConnectionsIndicates the number of output


connections from this logic slot.

(DevCtl)
Default: N/A
PtRes: HPM
Range: 0 to 12 (Logic), 0 to 2 (DevCtl)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

259

NOOVRRUN (ProcMOD)

NOOVRRUN (ProcMOD)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM

Number of OverrunsIndicates the number of times the point has overrun its
CNFPU allocation since the last reset.

Helpful Hint: NOOVRRUN is reset along with AVGPU and MAXPU

NOOVRRUN (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
0-4

Number of OverrunsSpecifies the number of times the point has overrun its
CNFPU allocation since the last reset

NOPGATE (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 4

Number of Primary GatesIndicates the number of primary gates configured


for a particular Device Control slot.

Helpful Hint: All configured primary gates must have at least one input.

NOPINPTS (RegPV)
Type:
Integer
Lock:
View
Default: Based on
PVALGID,
PVEQN, N
PtRes: HPM
Range: 0 to 6

260

Number of PV Input ConnectionsDefines the number of PV input


connections to this algorithm.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NOPTS(0 - 64)

NOPTS(0 - 64)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM

Number of Points Per CycleDefines ...


Index = 0 used for total count
Index = 1 - 64 used for per cycle count

Helpful Hint: The total count may not be equal to the sum of all cycles because most points are in more
than one cycle.

NORMCYCL
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
HPM
1 - 64
1 - 32
1 - 16
1-8
1-4
1-2
1

Normal Execution CycleSpecifies the normal execution cycle.

for points with PERIOD = 4 seconds


for points with PERIOD = 2 seconds
for points with PERIOD = 1 seconds
for points with PERIOD = 0.5 seconds
for points with PERIOD = 0.25 seconds
for points with PERIOD = 0.125 seconds
for points with PERIOD = 0.625 seconds

NORQUAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of Nodes to which UCN Requests are madeIndicates


the average number of UCN nodes per second that this node is requesting
communications with.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NORQUMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Maximum number of Nodes to which UCN Requests are madeIndicates


the maximum number of UCN nodes per second that this node is requesting
communications with.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

261

NORSPAVG (NIM, HPM Box)

NORSPAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
Average number of Nodes to which UCN Responses are madeIndicates
the average number of UCN nodes per second that this node is responding to.
View
0
HPM
N/A
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NORSPMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
Maximum number of Nodes to which UCN Responses are made
Indicates the maximum number of UCN nodes per second that this node is
View
responding to.
0
HPM
N/A
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NORSSEQ (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Eng/PB
2
HPM
2 to 12

Number of Ramp/Soak Pairs in the Sequence

NOSGATE (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 2

Number of Secondary GatesIndicates the number of secondary gates


configured for a particular Device Control slot.

Helpful Hint: All configured secondary gates must have at least one input.

NOSIOVRD (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

262

Real
View
0.0
HPM
0 (No limit)

Number of Safety Interlock OverridesThe number of safety interlock


overrides that have accumulated since the most recent reset of maintenance
statistics.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NOSTATES (DevCtl, DigComp)

NOSTATES (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
2
HPM

Number of Digital StatesDefines the number of states in this point.


State 1 is the first active state
State 0 is the inactive (middle) state
State 2 is the second active state
Refer to the HPM Control Functions and Algorithms manual for a detailed
description.
2 (Two states can be configured: STATE 0 and STATE 1)
3 (Three states can be configured: STATE 0, STATE 1, and STATE 2)

NOTRAAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of Nodes to which UCN Transactions are made. This


value indicates the average number of UCN nodes (per second) that this node
is communicating with (both requests and responses).

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NOTRAMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Maximum number of Nodes to which UCN Transactions are made. This


value indicates the maximum number of UCN nodes (per second) that this
node is communicating with (both requests and responses).

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NOTRANS02 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:

Real
View
0.0
HPM

Range:

0 (No limit)

R610
11/99

Accumulated TransitionsThe number of transitions to each state of the


OPFINAL parameter since the most recent reset of maintenance statistics. The
MAXTRAN parameter does not limit the number of transactions unless the user
writes a program to read MAXTRAN, comparing it to NOTRANS, and thereby
causing it to stop.

HPM Parameter Reference Dictionary


Honeywell Inc.

263

NPARAVG (NIM, HPM Box)

NPARAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of UCN Parameter Accesses per SecondAverage


number of UCN parameter accesses per second between this node and all other
nodes, including both requests and responses.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NPARMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Maximum number of UCN Parameter Accesses per SecondMaximum


number of UCN parameter accesses per second between this node and all other
nodes, including both requests and responses.

Real
View
0
HPM
N/A

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NPMSLOT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 250

Number of Process Module SlotsRefer to the HPM Control Functions and


Algorithms manual for a detailed description of HPM processing capacity.

NPRQUAVG(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of UCN Parameter RequestsAverage number of UCN


parameter requests per second issued from this node to node n.

NOTE
The node address (n) is an odd number (1, 3, 5,...63). Using an even number results in a
Parameter_Invalid error. Using n = 0 returns average total number of parameter requests
to all other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

264

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NPRQUMAX(0-64) (NIM, HPM Box)

NPRQUMAX(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Maximum number of UCN Parameter RequestsMaximum number of


UCN parameter requests per second issued from this node to node n.

NOTE
The node address (n) is an odd number (1, 3, 5,...63). Using an even number results in a
Parameter_Invalid error. Using n = 0 returns maximum total number of parameter
requests to all other nodes.
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NPRSPAVG(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of UCN Parameter ResponsesAverage number of UCN


parameter responses per second issued from this node to node n.

NOTE
The node address (n) is an odd number (1, 3, 5,...63). Using an even number results in a
Parameter_Invalid error. Using n = 0 returns average total number of parameter
responses to all other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NPRSPMAX(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Maximum number of UCN Parameter ResponsesMaximum number of


UCN parameter responses per second issued from this node to node n.

NOTE
The node address (n) is an odd number (1, 3, 5,...63). Using an even number results in a
Parameter_Invalid error. Using n = 0 returns maximum total number of parameter
responses to all other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

265

NPVSLOT (HPM Box)

NPVSLOT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 125

Number of Regulatory PV SlotsRefer to the HPM Control Functions and


Algorithms manual for a detailed description of HPM processing capacity.

NRMATRFL (DigComp, DevCtl, RegCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Normal Mode Attribute Flagindicates if this point is in the configured
Normal Mode attribute.
View
N/A
HPM
ON - (point is in the configured Normal mode attribute )
Off - (point is not in the configured Normal Mode attribute or Normal Mode attribute is
not configured)
Helpful Hint: If Normal mode attribute is not configured then the value returns to OFF.

NRMMODFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Normal Mode Flagindicates if the mode for this point is normal mode.
View
N/A
HPM
On - (Point is in configured normal mode)
Off - (Point is not in the configured normal mode or normal mode is not configured)

NSCANITM (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

266

Integer
View
0
HPM
0 - 50

Number of Scan Items in HPM Scan Table.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NSI0 (DevCtl, DigComp)

NSI0 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Inverted Interlocks ValueThe negative value of the corresponding interlock.
Engr
On
HPM
On (Safety interlock inactive)
Off (Safety interlock active)
Helpful Hint: This parameter can be changed by the engineer only if the point is inactive, or if the
HPM is idle.

NSTRING (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 16,384

Number of Strings in HPM Box Data Point

NSTRING (Array)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Number of Strings in Array Point String ArrayDefines the number of
strings (length specified by the STRLEN parameter) mapped to the Array point
PtBld
from either the HPM box (EXTDATA` IO_STR), or a serial interface IOP0
connected device (EXTDATA=IO_STR).
HPM
0 to 8 (When EXTDATA=IO_STR)
0 to 240 (When EXTDATA` IO_STR)
Helpful Hint: When EXTDATA` IO_STR, the range for this parameter applies regardless
of the value of the STRLEN parameter (up to 240 strings, either 8, 16, 32, or
64 characters in length can be mapped to the Array point from the HPM box).
When EXTDATA=IO_STR, only 64 characters of string data are available
(i.e., one 64-character string, two 32-character strings, four 16-character
strings, or eight 8-character strings).

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

267

NTIME (HPM Box)

NTIME (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 4,096

Number of Times in HPM Box Data Point

NTIME (Array)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
0 to 240

Number of Times in Array Point Time ArrayDefines the number of Times


the Array point has mapped from the HPM box.

NTIMER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
64
HPM
64

Number of Timer Points in the HPM Box Data Point

NTRAAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Average number of UCN Transactions Average number of UCN


Real
transactions (requests and responses) per second between this node and all
View
other nodes.
0
HPM
N/A
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NTRAMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

268

Maximum number of UCN Transactions Maximum number of UCN


Real
transactions (requests and responses) per second between this node and all
View
other nodes.
0
HPM
N/A
Helpful Hint: This statistic can be viewed on the Toolkit Displays.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NTRQUAVG(0-64) (NIM, HPM Box)

NTRQUAVG(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of UCN Transaction RequestsAverage number of UCN


transaction requests per second issued from this node to node n.

NOTE
The node address (n) is typically an odd number (1, 3, 5,...63). Using an even number
results in a Parameter_Invalid error. Using n = 0 returns average total number of
transaction requests to all other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NTRQUMAX(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Maximum number of UCN Transaction RequestsMaximum number of


UCN transaction requests per second issued from this node to node n.

NOTE
The node address (n) is an odd number (1, 3, 5,...63). Using an even number results in a
Parameter_Invalid error. Using n = 0 returns maximum total number of transaction
requests to all other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NTRSPAVG(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0
HPM
N/A

Average number of UCN Transaction ResponsesAverage number of


UCN transaction responses per second issued from this node to node n.

NOTE
The node address (n) is an odd number (1, 3, 5,...63). Using an even number results in a
Parameter_Invalid error. Using n = 0 returns average total number of transaction
responses to all other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

269

NTRSPMAX(0-64) (NIM, HPM Box)

NTRSPMAX(0-64) (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Maximum number of UCN Transaction ResponsesMaximum number of


UCN transaction responses per second issued from this node to node n.

Real
View
0
HPM
N/A

NOTE
The node address (n) is an odd number (1, 3, 5,...63). Using an even number results in a
Parameter_Invalid error. Using n = 0 returns maximum total number of transaction
responses to all other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

NTWKNUM
FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: N/A`
PtRes: NIM
Range: 1 to 20

None
Network NumberDefines on which UCN the NIM and HPMs reside.

NUMPECMS(1-10) (SECM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: IOP
Range: 0 to 2

None
Number of PECMsThis is an arrayed parameter that displays the number of
FBAP VFDs (PECMs) configured for a given device. The current limit is two
FBAP VFDs (PECM) for a given device

NUMSCHD (SECM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: 0
PtRes: IOP
Range: 0 - 2

270

Network Management Information Block


Number of SchedulesThis parameter displays the number of
schedules loaded into the stack. Currently the stack that the IOP uses
can handle up to a maximum of two schedules.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NUMVW(3)-(4) (FBCM, PECM)

NUMVW(3)-(4) (FBCM, PECM)


FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: 1
PtRes: IOP
Range: 1-2

Number of VIEW_3, Number of VIEW_4


Number of VIEW ObjectsThese parameters define the number of
View-3 or View-4 objects, respectively, in the resource/function block.

NXTPINAM
Type:
Lock:
Default:
PtRes:
Range:

String_8
Eng
N/A
IOP
?

Next Personality Image FileDefines the personality Image file that will be
loaded on the next personality load request for this IOP.

NXTSOAKV (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
N/A
HPM
> 0.0

Next Soak Value

HPM Parameter Reference Dictionary


Honeywell Inc.

271

OFFNRMFL

-OOFFNRMFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
Off-Normal Alarm FlagIndicates whether an off-normal alarm has been
detected at this data point.
View
Off
HPM
Off (No alarm)
On (Current PV state is not the same as the configured PVNORMAL state.)

OFFNRMPR
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Offnormal Alarm PriorityIndicates priority of the off normal or change of


state alarms.
ENGR
Low
NIM
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

OFFNRMPR (FBCM)
FF Param. Source:
DISC_PRI
Type:
E:ALPRIOR Offnormal Alarm PriorityIndicates priority of the off normal or change of
state alarms.
Lock:
View
Default: Low
PtRes: NIM
Range: This value is mapped from the fieldbus alert priority parameter as follows:
15 - Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
10-14 - High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
5-9 - Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
4 - JnlPrint (Alarm is historized and reported to the printer but not annunciated)
3 - Printer (Alarm is reported to the printer but not historized and not annunciated)
2 - Journal (Alarm is historized but not reported to the US/GUS and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

272

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OFFPULSE (DigOut)

OFFPULSE (DigOut)
Type:
Lock:
Default:
PtRes:
Range:

Real
Off Pulse CommandCommand that sets output SO to Off for the specified
number of seconds. At the end of the pulse time, SO is set to On. If 0.0 is
Oper
entered for OFFPULSE, SO is immediately set to On.
N/A
HPM
0.0 to 60.0 seconds
Helpful Hint: OFFPULSE can be written to by only those entities that possess the
HPMM Cont_Ctl (continuous control) access level. These are Digital
Composite points, Logic points, and Regulatory Control Position
Proportional points.

OLDAV (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
>0

Old Accumulated ValueThe value of parameter AV (accumulated value) just


before the accumulator was reset. This parameter makes the previous
accumulated value available for those functions that need it.

OLDAV (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
> 0.0

Old Accumulated ValueThe value of parameter PVCALC (calculated PV)


just before it is reset. This parameter makes the previous total available to those
functions that need it.

ONPULSE (DigOut)
Type:
Lock:
Default:
PtRes:
Range:

Real
On Pulse CommandCommand that sets output SO to On for the specified
number of seconds. At the end of the pulse time, SO is set to Off. If 0.0 is
Oper
entered for ONPULSE, SO is immediately set to Off.
N/A
HPM
0.0 to 60.0 seconds
Helpful Hint: ONPULSE can be written to by only those entities that possess the HPMM
Cont_Ctl (continuous control) access level. These are Digital Composite
points, Logic points, and Regulatory Control Position Proportional points.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

273

OP (AnalgOut)

OP (AnalgOut)
Type:
Lock:
Default:
scale
PtRes:
Range:

Real
Oper
-6.9% of full

Output in PercentDefines the output value from this point in percent.

HPM
-6.9 to 106.9%
Helpful Hint: To manually change the output value requires MODE = Man and
REDTAG = Off.

OP (DevCtl, DigComp)
Type:
E:SDDigital State OutputIndicates the last commanded output
state. See also OPFINAL. For Status Outputs, use SO.
ENM:STATETXT
Lock:
Oper
Default: STATETXT(0)
PtRes: HPM
Range: STATETXT(0) Descriptor
STATETXT(1) Descriptor
STATETXT(2) Descriptor (internally set to $NULL for two-state devices)
STATETXT(3) None (Not configurable)
Helpful Hint: OP indicates text for the last commanded output state (i.e., On, Run, etc.).
Output state change requires MODE = Man, SHUTDOWN = Off, and
REDTAG = Off.

OP (DigOut)
Type:
Lock:
Default:
PtRes:
Range:

Real
Prog
0.0%
HPM
0.0 to 100.0%

Pulsed Digital OutputOP is the percent on-time for the pulsed output. It can
be written to by only the controlling slot in the HPMM, such as from the PosProp
RegCtl algorithm. Output change requires DOTYPE = Pwm. OP (DigOut) has
the same access-level requirement as OFFPULSE and ONPULSE; the writing
entity must have an HPMM access level of Cont_Ctrl (continuous
control). For Status Outputs, use SO.
For direct action, pulse-on time is calculated as follows:
Pulse On-Time = OP% * PERIOD
100
For reverse action:
Pulse On-Time = 100% - OP% * PERIOD
100
Refer to PERIOD parameter for length of period.

274

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OP (FBCM)

OP (FBCM)
FF Param. Source:
Type:
Real
Lock:
Oper
Default: NaN
PtRes: FF DEVICE

AO, PID: OUT.Value


OutputDefines output value in percent.

Range: OUT_SCALE +/- 10 %

OP (RegCtl)
Type:
Lock:
Default:
scale
PtRes:
Range:

Real
Oper
-6.9% of full
HPM
-6.9 to 106.9%

Regulatory Control OutputOP is derived from CV, the variable


calculated by the control algorithm. OP is checked for minimum output
change, output rate-of-change, and output high and low limits. If any of
the limits is exceeded, OP is adjusted or clamped as applicable. OP
remains in percent of full scale if it is going to a final control element
through an IOP Card. If OP is going to a secondary data point, its value
is converted to the engineering units of the receiving data
point's setpoint (SP).

Helpful Hint: OP change requires MODE = Man, SHUTDOWN = Off, and REDTAG = Off.
If the OP is manually set above or below the OP limits and the mode is then
changed to automatic or cascade, a process bump may occur.

OPALDB (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:
Units

Real
EngPB
5 Output Units
HPM
0 to 25 Output

Output Alarm Dead BandThe deadband for the Regulatory Control


OP alarm. It is used to prevent excessive recurrence of alarms by
adjusting the range of the output at which the alarm "returns to normal."
Available on Release 510 and later software.

Helpful Hint: The value of OPALDB must be less than or equal to (OPHITP - OPLOTP)/2.

OPCHAR
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
PtBld
Off
HPM

Output Characterization OptionDefines whether the output


characterization option is to be used for this data point. If this option is
to be implemented, the user must supply the values for the input
coordinates (OPIN 14) and output coordinates (OPOUT 14). Refer to
the HPM Control Functions and Algorithms manual for a detailed
description of output characterization.
On (Output characterization is to be used)
Off (Output characterization is not to be used)

HPM Parameter Reference Dictionary


Honeywell Inc.

275

OPCMD (DevCtl, DigComp)

OPCMD (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Output Command
Prog
Off
HPM
Off (Commands the output state to State0)
On (Commands the output state to State1)
Helpful Hint: If state change did not occur, OPCMD has to be set to the current state,
and then to the desired state.

OPCMD
Type:
Lock:
Default:
PtRes:
Range:

E:$OPCMD
Output CommandIndicates the current output command.
View
NA
HPM
0-Idle (Output is not being affected by Output Command)
1-Lower (Output is being lowered)
2-Raise (Output is being raised)

OPEU
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A

Output Value in Engineering Units

OPFINAL (AO)
Type:
Real
Lock:
View
Default: -6.9% of
full scale
PtRes: HPM
Range: N/A

276

Final Percent Output Sent to Control ElementOutput value after


direct or reverse control action and output characterization have all been
applied. If output has been configured for direct action (OPTDIR),
0.0% represents 4 mA to the control element and 100% represents 20
mA. If configured for reverse action, 0.0% represents 20 mA, and
100% represents 4 mA.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OPFINAL (DevCtl, DigComp)

OPFINAL (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

E:STATETXT
Oper
Statetxt(0)
Final Output Sent to Control ElementThe output value that was last stored.
This value can differ from the OP parameter if a sealin has occurred, state
HPM
change is active, or the Array/SI read-back check evaluates OPFINAL to be
NONE. If LOCALMAN = ON, then OP and OPFINAL follow the PV.
Statetxt(0) (Self-defining enumeration)
Statetxt(1) (Self-defining enumeration)
Statetxt(2) (Self-defining enumeration)internally set to $NULL for two-state devices.
Statetxt(3) NONE (not configurable)

OPHAFL (RegCtl)
Type:
Lock:
Default:
PtRes:

Logical
View
Off
HPM

Range:

Off (OP High alarm is off)


On (OP High alarm is on)

Output High Alarm FlagIndicates when a Regulatory Control Output High


alarm has been detected at this data point. This flag is set when the output value
(OP) exceeds OPHITP and is reset when OP is below OPHITP minus the
deadband. Available on Release 510 and later software.

Helpful Hint: Refer to the diagram with OPLAFL.

OPHIFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Output High Limit FlagIndicates whether the OP value has reached its upper
limit specified by OPHILM. If this parameter is set by a program, it will inhibit
Prog
raise commands.
Off
HPM
Off
On (OP value has reached its upper limit)

OPHILM
Type:
Lock:
Default:
PtRes:
Range:

Real
Output High Limit in Percent
Supr
105.0%
HPM
OPLOLM to 106.9%,
NaN
Helpful Hint: Entering NaN disables limit checking by forcing OPHILM to its extreme value
(106.9%).

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

277

OPHIPR (RegCtl)

OPHIPR (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:Alprior
Output High Alarm PrioritySpecifies the priority of the Regulatory Control
Output High alarm. Available on Release 510 and later software.
EngPB
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

OPHISRC
Type:

Universal
Output High Flag Input SourceDefines the input connection that fetches the
Ent.Prm
OPHIFL parameter to determine windup state.
Lock:
PtBld
Default: Null
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.
Some possible input-connection sources are
a."DigIn slot Tagname.PVFL"
b."Logic slot Tagname.SO(nn)" where nn = 124
c."Logic slot Tagname.Fl(nn)" where nn = 112
d."ProcMod slot Tagname.Fl(nnn)" where nnn = 1127
e."Box Flag slot Tagname.PVFL
f."!Box.FL(nnnn)" for a box flag that resides in the same box where nnnn = 116, 384
g."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the NIM UCN address, xx is the HPM box number, and
nnnn = 14095 (Data access limit)
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DI (Digital Input)
mm is the IOP Card number (140)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

278

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OPHITP (RegCtl)

OPHITP (RegCtl)
Type:
Lock:
Default:
PtRes:

Real
Supr
NaN
HPM

Output High Alarm Trip PointThe Regulatory Control Output High alarm is
set when the output value (OP) exceeds the high alarm limit specified by
OPHITP. The alarm is removed when OP returns to normal. A suitable dead
band is provided by OPALDB. See also OPHIPR and the drawing with
OPLAFL. Available on Release 510 and later software.

Range:

OPLOTP to OPHILM, NaN


Helpful Hint: The Regulatory Control Output High alarm is only available for points configured as full.
The alarm is disabled if OPHITP is not configured.

OPIN0
Type:
Lock:
Default:
PtRes:
Range:

Real
View
-6.9%
HPM
N/A

Input Coordinate Number 0 in PercentDefines the OPIN0 coordinate when


output characterization has been selected (OPCHAR is On). This coordinate is
fixed at -6.9%.

OPIN14
Type:
Lock:
Default:
PtRes:
Range:

Real
Input Coordinate Number 1, 2, 3, or 4 in PercentDefine the OPIN1OPIN4
coordinates when output characterization has been selected (OPCHAR is On).
Supr
N/A
HPM
` previous coordinate
` next coordinate

OPIN5
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
106.9%
HPM
N/A

Input Coordinate Number 5 in PercentDefines the OPIN5 coordinate when


output characterization has been selected (OPCHAR is On). This coordinate is
fixed at 106.9%.

HPM Parameter Reference Dictionary


Honeywell Inc.

279

OPLAFL (RegCtl)

OPLAFL (RegCtl)
Type:
Lock:
Default:
PtRes:

Logical
View
Off
HPM

Output Low Alarm FlagIndicates if a Regulatory Control Output Low alarm


has been detected at this data point. This flag is set when the output value (OP)
is less than OPLOTP and is reset when OP is above OPLOTP plus the deadband.
Available on Release 510 and later software.

Range:

Off (OP Low alarm is off).


On (OP Low alarm is on).

The drawing below illustrates the relationship of the output high/low alarm flags, the low alarm
trip point OPLOTP, and the deadband OPALDB.
OP

OPHITP
OPALDB

OPHAFL is turned off


if OP is below this point

OPLAFL is turned off


if OP is above this point
OPHITP - OPALDB
OPALDB

OPLOTP + OPALDB
OPLOTP
0

OPLOFL
Type:
Lock:
Default:
PtRes:
Range:

280

Logical
Output Low Limit FlagIndicates whether the output value OP has reached
the low limit. This parameter must be set by a program or logic point. It will
Prog
inhibit "raise" commands.
Off
HPM
Off (OP is above the low limit)
On (OP has reached the low limit)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OPLOLM

OPLOLM
Type:
Lock:
Default:
PtRes:
Range:

Real
Output Low Limit in Percent
Supr
-5.0%
HPM
-6.9% to OPHILM,
NaN
Helpful Hint: Entering NaN disables limit checking by forcing OPLOLM to its extreme
value (-6.9%).

OPLOPR (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:Alprior
Output Low Alarm PrioritySpecifies the priority of the Regulatory Control
Output Low alarm. Available on Release 510 and later software.
EngPB
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

HPM Parameter Reference Dictionary


Honeywell Inc.

281

OPLOSRC

OPLOSRC
Type:

Universal
Output Low Flag Input SourceIndicates which input connection fetches the
OPLOFL parameter to determine the windup state.
Ent.Prm
Lock:
HPM
Default: PtBld
PtRes: Null
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.
Some possible input-connection sources are
a."DigIn slot Tagname.PVFL"
b."Logic slot Tagname.SO(nn)" where nn = 124
c."Logic slot Tagname.Fl(nn)" where nn = 112
d."ProcMod slot Tagname.Fl(nnn)" where nnn = 1127
e."Box Flag slot Tagname.PVFL
f."!Box.FL(nnnn)" for a box flag that resides in the same box where nnnn = 14095
g."$NMhhBxx.FL(nnnn)" for a box flag that resides in a different HPM box on the same UCN; hh
is the NIM UCN address, xx is the HPM box number, and
nnnn = 14095 (Data access limit)
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as DI (Digital Input)
mm is the IOP Card number (140)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

OPLOTP (RegCtl)
Type:
Lock:
Default:
PtRes:

Real
Supr
NaN
HPM

Range:

OPLOLM to OPHITP, NaN

Output Low Alarm Trip PointThe Regulatory Control Output Low alarm is
set when the output value (OP) drops below the low alarm limit specified by
OPLOTP. The alarm is removed when OP returns to normal. A suitable dead
band is provided by OPALDB. See also OPLOPR. Available on Release 510
and later software.

Helpful Hint: The Regulatory Control Output Low alarm is only available for points configured as full.
The alarm is disabled if OPLOTP is not configured.

282

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OPMCHLM

OPMCHLM
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
> 0.0,
NaN

Output Minimum Change in Percent

Helpful Hint: OP changes only if new output % - old output % is greater than the percentage
in parameter OPMCHLM. Entering NaN disables limit checking by forcing
OPMCHLM to its extreme value (0.0).

OPOUT0
Type:
Lock:
Default:
PtRes:
Range:

Real
View
-6.9%
HPM
N/A

Output Coordinate Number 0 in PercentDefines the OPOUT0 coordinate


when output characterization has been selected. (OPCHAR = On) This
coordinate is fixed at a value of -6.9%.

OPOUT14
Type:
Lock:
Default:
PtRes:
Range:

Real
Output Coordinates Number 1, 2, 3, or 4 in PercentDefine the OPOUT1
OPOUT4 coordinates when output characterization has been selected (OPCHAR
Supr
is On).
N/A
HPM
` previous coordinate
` next coordinate

OPOUT5
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
View
106.9%
HPM
N/A

Output Coordinate Number 5 in PercentDefines the OPOUT5 coordinate


when output characterization has been selected. (OPCHAR = On) This
coordinate is fixed at a value of 106.9%.

HPM Parameter Reference Dictionary


Honeywell Inc.

283

OPRATRFL (DevCtl, DigComp, RegCtl)

OPRATRFL (DevCtl, DigComp, RegCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Operator Mode Attribute FlagIndicates whether the current mode attribute
is Operator.
View
N/A
HPM
Off (Current mode attribute is Program or None)
On (Current mode attribute is Operator)

OPRINPUT (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Real
Oper
0.0
HPM
N/A

Operator InputDefines the value entered by the operator in response to the last
sequence message.

OPROCLM
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
NaN
HPM
> 0.1
NaN

Output Rate of Change Limit in Percent Per Minute

Helpful Hint: Entering NaN disables limit checking.

OPTDIR (AO)
Type:
Lock:
Default:
PtRes:
Range:

284

E:POLARITY Analog Output Direct/Reverse ActionDefines the output action of the


OPFINAL value of the data point.
Eng/PB
Direct
HPM
0-Direct (For final OP: 0% = 4 mA; 100% = 20 mA)
1-Reverse (For final OP: 0% = 20 mA; 100% = 4 mA)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OPTDIR (DigOut)

OPTDIR (DigOut)
Type:
Lock:
Default:
PtRes:
Range:

E:POLARITY Output DirectionDefines the direct/reverse action of the PWM digital


output.
Eng/PB
Direct
HPM
0-Direct (OP is the % On time)
1-Reverse (OP is the % Off time)

OROFFSET (ORSel)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Override OffsetWhen OROFFSET is On, override initialization of Pid-type
algorithm points connected to this ORSel algorithm applies an override offset
Eng/PB
equal to Gain times Error (PV - SP).
On
HPM
Off (No override offset is applied)
On (Offset of Gain times Error is applied)

OROPT (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
Override OptionAllows the operator to bypass permissive and override
interlocks by setting BYPASS On.
Eng/PB
Off
HPM
On (Override option enabled)
Off (Override option disabled)

HPM Parameter Reference Dictionary


Honeywell Inc.

285

OROPT (ORSel)

OROPT (ORSel)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Eng/PB
Off
HPM

Override OptionDefines whether the operator can put the point in a bypass
state where any of the X1-X4 inputs can be bypassed. Also, when on, the
feedback value is propagated to nonselected primaries of the override selector
algorithm. Refer to the HPM Control Functions and Algorithms manual for a
detailed description.
Off (No override)
On (Inputs can be overridden)

OUT(0)(12) (GenLin)
Type:
Lock:
Default:
PtRes:
Range:

Real
Output Coordinates 0 -12Define the output value at the respective
coordinates.
Supr
NaN
HPM
Any value but NaN

OUT(1-8) (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: IOP
Range: Floating Point

Configurable through Link Object


OutThis is an arrayed parameter. It contains the analog-point values
that are used for non-control input connections to TPSN from the
published output connection of the fieldbus network.

OUTCONCT
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

None
This parameter set has been added for compatibility with fieldbus
requirements.

OUTD(1)-(8) (FBCM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: Off
PtRes: FF DEVICE
Range: 0-Off
1-On

286

Configurable through Link Object


Out DiscreteThis is an arrayed parameter. It contains the discretepoint values that can be used for non-control input connections to the
TPSN from the published output connection of the fieldbus network.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OUTDST(1-8) (FBCM)

OUTDST(1-8) (FBCM)
FF Param. Source:
Configurable through Link Object
Type:
E:$FBSTATS Out Discrete StatusThis is an arrayed parameter. It contains the
status of a discrete point that can be used for non-control input
Lock:
View
connections to the TPSN from the published output connection of the
Default: Bad_OOS
fieldbus network.
PtRes: IOP
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

OUTST(1-8) (FBCM)
FF Param. Source:
Configurable through Link Object
Type:
E:$FBSTATS Out StatusThis is an arrayed parameter. It contains the status of an
analog point that can be used for
Lock:
View
non-control input connections to the TPSN from the published output
Default: Bad_OOS
connection of the fieldbus network.
PtRes: IOP
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

OVERFLOW
Type:
Lock:
Default:
PtRes:
Range:

Logical
Accumulation Overflow FlagIndicates whether the accumulated value has
overflowed.
View
Off
HPM
Off (No overflow)
On (Overflow)

OVERLAP (Array)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
Overlapping Array Slot NumberIndicates the Array slot number containing
the data being referenced by the slot currently being built.
View
0
HPM
0 through the number of Array slots (NARRSLOT)

HPM Parameter Reference Dictionary


Honeywell Inc.

287

OVERPHAS (ProcMod)

OVERPHAS (ProcMod)
Type:
Lock:

E:JUMPDIR Override Current PhaseAllows the operator to override the current phase of
ONPROC and the sequence by skipping forward to the next phase, or backward to the previous
CNTLLOCK phase. A phase can be overridden in this manner only when the sequence
execution state is PAUSE, FAIL, or ERROR.
parameters
Default: Blank
PtRes: HPM
Range: 0-Forward (Skip to next phase)
1-Backward (Go back to previous phase)

OVERSTAT (ProcMod)
Type:
Lock:

E:JUMPDIR Override Current StatementAllows the operator to override the current


ONPROC and statement of the sequence by skipping forward to the next statement, or
CNTLLOCK backward to the previous statement. A statement can be overridden in this
manner only when the sequence execution state is PAUSE, FAIL, or ERROR.
parameters
Default: Blank
PtRes: HPM
Range: 0-Forward (Skip to next statement)
1-Backward (Go back to previous statement)

OVERSTEP (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

288

E:JUMPDIR Override Current StepAllows the operator to override the current step of the
sequence by skipping forward to the next step, or backward to the previous step.
ONPROC
A step can be overridden in this manner only when the sequence execution state
Blank
is PAUSE, FAIL, or ERROR.
HPM
0-Forward (Skip to next step)
1-Backward (Go back to previous step)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OVERVAL

OVERVAL
Type:
Lock:
Default:
PtRes:
Range:

Integer
Eng/PB
25
NIM

Overview Value in PercentDefines the amount of deviation (PV - SP, in


percent) that causes the PV to reach the overview limit. For digital points, the
display shows the current state of the point.
As shown in Figure O-1, The baseline shows the normal operating value for this
PV.
0 to 100 (Entering a 0 suppresses the value; value is not shown on the display)

OVERVIEW LIMIT

DEVIATION TO REACH
OVERVIEW LIMIT

BASELINE
(Normal Value)

Figure O-1 Overview Limit

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

1302

289

OVRCTIM (DevCtl)

OVRCTIM (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Time Over High Trip LimitThe amount of time the SECVAR parameter is
Time
continuously greater than the SECVAR high trip limit.
View
0
HPM
Duration (0 to 9999 days, with a resolution to 1 second)

OVRDALOP (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Override Alarm OptionThe override alarm option for I0, I1, and I2
E:$OVRALOP
parameters.
Eng/PB
None
HPM
0-None (No override alarming)
1-Auto_Rtn (Return to normal when override is cleared)
2-Cnfm_Rqd (Confirm to clear, after interlock is cleared)

OVRDALPR (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Override Alarm PriorityDefines the priority of an override alarm.


E:ALPRIOR
Engr
Low
HPM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

OVRDCONF (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

290

Override Confirmation FlagIndicates one of the four override alarms


Logical
SI0CONF or I0CONF-I2CONF has not yet been confirmed. This flag is also
Oper
used to confirm the alarm.
Off
HPM
Off (An alarm is not waiting for confirmation)
On (An alarm is waiting for confirmation)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

OVRDDESC (DevCtl, DigComp)

OVRDDESC (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:

String_8
View
Blank
HPM

Override Alarm DescriptorInput connections and logic gating are examined


in order to determine which input was the source of change for the interlock. For
the Device Control point, descriptor text for this parameter is taken from
LIDESC (1-12). Descriptive text for the Digital Composite point is taken from
SI0 DESC or I0-I2 DESC parameters.

Range:

SI0 Desc (Current interlock or input descriptor)


I0 - I2 Desc (Current interlock or input descriptor)
L1 - L12 Desc (Current interlock or input descriptor, Device Control only)

OVRDI0FL, OVRDI1FL, OVRDI2FL, OVRDSIFL


(DevCtl, DigComp)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
Override and Safety Override Alarm FlagIndicates that an override is
active, or that a confirmable override was cleared, but not yet confirmed.
View
Off
HPM
Off (Override flag is not active)
On (Override flag is active)

HPM Parameter Reference Dictionary


Honeywell Inc.

291

P (FlowComp)

-PP (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
1.0
HPM
> 0.0

Pressure InputIndicates the measured actual gage pressure.

P0 (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
N/A

Zero Reference for PressureP0 is the zero reference pressure input and is in
the same engineering units as the P input. P0 is typically 14.696 if P is in psig or
101.325 if P is in kiloPascals. Enter the absolute value of the number.

P0P2 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:

Logical
Engr
On
HPM

Range:

Off (Respective state is locked out)


On (Respective state is permitted to be used)

Permissive Interlocks for Output States 0, 1, & 2Permissive interlocks are


controlled by logic slot outputs, and each interlock determines whether the
operator and user program are allowed to use the respective state, or are locked
out from that state. A permissive interlock (P0-P2) is provided for each state
(STATE0-STATE2). The permissive interlocks themselves never cause the
outputs to change. P0-P2 can be changed by a logic block or a program when
the point is active and the mode attribute is Program. Refer to the HPM Control
Functions and Algorithms manual for a detailed description.

Helpful Hint: P0P2 configuration requires PTEXECST = InActive or PNTSTATE = Idle.

P1P6 (RegPV)
Type:
Lock:
Default:
PtRes:
Range:

292

Real
View
NaN
HPM
N/A,
NaN

PV Inputs 1-6Indicates the current values at the inputs to the RegPV


algorithm. For Totalizers, P2 is the floating point input of AV.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

P1STSP6STS

P1STSP6STS
Type:
Lock:
Default:
PtRes:
Range:

E:PVVALST
P1P6 StatusIndicate the status of the up to six inputs at the RegPV
View
algorithm.
Bad
HPM
0-Bad (Value is bad and replaced with NaN)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

PAGE
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

None
This parameter set provides for compatibility with fieldbus
requirements.

PAGE01
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

None
This parameter set provides for compatibility with fieldbus
requirements.

PAUSETIM (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Integer
State 0 Pause TimeThe amount of time to pause in State 0 on an OP state
Supr
change, if the STCHGOPT parameter equals STATE0.
0
HPM
0 to 1000 seconds

PDDTLST(1-10) (SECM)
FF Param. Source:
Type:
String
Lock:
View
Default: Null String
PtRes: IOP
Range: N/A

R610
11/99

None
Device Management VFD Detailed Status This arrayed parameter
shows the detailed status for a management VFD of a configured
device. Each entry in this array has a corresponding entry (same index)
in the PDSTAT parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

293

PDSTAT(1)-(10) (SECM)

PDSTAT(1)-(10) (SECM)
FF Param. Source:
Type:
E:$PDSTAT
Lock:
View
Default: Null
PtRes: IOP

Range:

None
Device Management VFD Status This arrayed parameter shows the
detailed status for a management VFD of a configured device. Each
entry in this array has a corresponding entry (same index) in the
PDSTAT parameter.
The associated PECMs status parameter (DEVSTAT) will be set to
BAD when states 0, 1, 2, or 4 of PDSTAT are set.
Each element of this array has a corresponding element in PDDTLST.

0 Null
1 OffNet
2 Mismatch
3 OnLn_OK
4 OnLn_BAD

PDTAG (SECM)
FF Param. Source:
Type:
String
Lock:
View
Default: FBUS IOP
LINK?
PtRes: IOP
Range: N/A

System Management Information Block


Physical Device Tag This parameter shows the IOP physical device
tag and it is used for display purposes only. The last character in the
default value (the question mark) for this parameter can be 1, 2, 3, or
4 if the SECM point that the parameter is associated with has an
fieldbus IOP slot number that is 120, 121, 122, or 123, respectively.

PERIOD (ProcMod, Timer)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
1 seconds
HPM
1 seconds

PeriodDefines the processing period in seconds.

PERIOD (DevCtl, DigComp, Logic, RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

294

Real
PeriodDefines the processing period in seconds.
View
1 second
HPM
0.25, 0.5, or 1.0 seconds

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PERIOD

PERIOD
Type:
Lock:

Real
PtBld

Periodspecifies the scan period in seconds.

Default: .25 sec for Logic, DigComp, & DevCtl


.50 sec for RegPv and RegCtl
1.00 sec for ProcMod
PtRes: HPM
Range: 0.0625, 0.125, 0.25, 0.5, 1.0, 2.0, and 4.0 seconds

PERIOD (DigOut)
Type:
Lock:
Default:
PtRes:
Range:

Real
PeriodDefines length of period for an SO output from DigOut point that has
Eng/PB
been configured for a PWM output.
10.0 seconds
HPM
1.0 to 120.0 seconds

PFDLYFL (RegCtl, RegPV, DevCtl, DigComp, Logic,


ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
PreFetch Delayed FlagSet when prefetch data is not available for slot
View
execution.
Off
HPM
Off (prefetch data is available for slot execution.)
On (prefetch data is not available for slot execution.)

PGALGID(1)(4) (DevCtl)
Type:

E:$GTALGID Primary Gate Algorithm IDDefines the algorithm IDs for primary gates.
in an Array
The Boolean logic gates beginning with P have a user-defined pulse size.
(1..4)
Lock:
PtBld
Default: Null
PtRes: HPM
Range: NULL (No algorithm)
AND (And Gate algorithm)
OR (Or Gate algorithm)
NAND (Nand Gate algorithm)
NOR (Nor Gate algorithm)
XOR (Exclusive Or Gate algorithm)
PAND (Pulse Nand Gate algorithm)
POR (Pulse Or Gate algorithm)
PNAND (Pulse Nand Gate algorithm)
PNOR (Pulse Nor Gate algorithm)
PXOR (Pulse Exclusive-Or Gate algorithm)
R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

295

PGDSTN(1)(4) (DevCtl)

PGDSTN(1)(4) (DevCtl)
Type:

E:$GATDSTN Primary Gate DestinationDefines the output destination of the primary gate.
in an Array
(1..4)
Lock:
PtBld
Default: None
PtRes: HPM
Range: None (No destination)
SI0 (Output goes to Safety Interlock)
I0, I1, I2 (Output goes to Interlock)
P0, P1, P2 (Output goes to Permissives)
SOCMD0, SOCMD1, SOCMD2 (Output is commanded to go to SOCMD0, 1 or 2)
OPCMD (Output is commanded to go to OPCMD parameter)
SG1, SG2 (Output goes to Secondary gates 1 or 2)

PGPLSWTH(1)(4) (DevCtl)
Type:

Integer
Primary Gate Pulse WidthIndicates the pulse width for primary gates whose
in an Array
algorithm starts with a P.
(1..4)
Lock:
Supr
Default: 0
PtRes: HPM
Range: 0 to 8000 seconds

PGSO(1)(4) (DevCtl)
Type:

Logical
in an Array
(1..4)
Lock:
View
Default: Off
PtRes: HPM
Range: Off
On

Primary Gate Status OutputIndicates the output value of the primary gate.

PHASE (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

296

String_8
View
Spaces
HPM
N/A

Phase NameIndicates the current phase of the sequence executing in the


process module.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PHASEAL (ProcMod)

PHASEAL (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Phase AlarmIndicates whether the current phase of the sequence has been
completed within the specified time.
View
Off
HPM
On (Phase has not been completed in the specified time)
Off (No phase alarm)

PHASETIM (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Phase Time Indicates the time remaining in minutes in the current phase
before a phase alarm is generated. The maximum time allowed for the phase is
View
defined by the phase statement.
0 seconds
HPM
0 to 9999 minutes

PHREMTIM (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Time
View
0 seconds
HPM
N/A

Phase Time RemainingIndicates the time remaining in time duration before a


phase alarm is generated. This value is displayed in the HPM Detail display.

PIALGID (1)(12) (DevCtl)


Type:

E:$I1ALGID Primary Input Gate Algorithm IDThe XX algorithms compare this input to
in an Array
the PINN (1)-(12) parameter, and the IN_SET algorithm compares it to the range
of 10 values in the NNINSET (1)-(10) parameter. The XX2 algorithms compare
(1..12)
this input defined by the PISRC(1)-(12) parameter.
Lock:
PtBld
Default: Null
PtRes: HPM
Range: NULL (No algorithm)
INVERT (Invert Logical algorithm)
GT (Greater Than algorithm)
GE (Greater Than or Equal To algorithm)
LT (Less Than algorithm)
LE (Less Than or Equal To algorithm)
EQ (Equal To algorithm)
NE (Not Equal To algorithm)
GT2 (Greater Than algorithm)
GE2 (Greater Than or Equal To algorithm)
LT2 (Less Than algorithm)
LE2 (Less Than or Equal To algorithm)
EQ2 (Equal To algorithm)
NE2 (Not Equal To algorithm)
IN_SET (Compares the input to values in the INSET array)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

297

PIDEADBD(1)(12) (DevCtl)

PIDEADBD(1)(12) (DevCtl)
Type:

Real
in an Array
(1..12)
Lock:
Supr
Default: 1.0
PtRes: HPM
Range: >0

Primary Input Gate DeadbandThe deadband for primary input gates that
is configured for an arithmetic algorithm.

PIDFORM
Type:
Lock:
Default:
PtRes:
Range:

E:PIDFORM
PID Controller FormDefines the type of Pid controller form. Refer to the
Eng/PB
HPM Control Functions and Algorithms manual for a detailed description.
Interact
HPM
0-Interact [(Proportional + Integral) x Derivative]
1-Ideal (Proportional + Integral + Derivative)

PIDSTN(1)-(6)
Type:
Ent.Prm
PV Input Connection DestinationDefines the parameter in the data point that
is to receive the value provided by the respective input connection. There can be
Lock:
View
up to six input-connection destinations for a RegPV point.
Default: Based on
PVALGID,
PVEQN, & N
PtRes: HPM
Range: 18 character valid parameter name

PINN (1)(12) (DevCtl)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
<> NaN

Primary Input Constants NumericThe numeric constant for arithmetic


comparisons of primary input gates using XX algorithms.

PISO (1)(12) (DevCtl)


Type:

Logical
in an Array
(1..12)
Lock:
View
Default: Off
PtRes: HPM
Range: Off
On

298

Primary Input Gate Output ValueIndicates the output value of the primary
input gate.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PISRC(1)(12) (DevCtl)

PISRC(1)(12) (DevCtl)
Type:

E:$GATESRC Primary Input SourceThe source for the second input of primary input gates
for arithmetic comparison algorithms that use a second external input (i.e., XX2
in an Array
algorithms).
(1..12)
Lock:
PtBld
Default: Null
PtRes: HPM
Range: NULL (No source for input)
L1..L12 (These values correspond with the LISRC(1)(12) parameter)

PISRC(1)PISRC(6)
Type:
Lock:
Default:
PtRes:
Range:

Ent.Prm
PtBld
null.null
HPM

PV Input Connection SourceDefine the parameters whose current values are


to be fetched and then written to the up to six RegPV algorithm inputs. The
source parameter name can be specified using the "Tagname.Parameter" format.
Refer to the HPM Control Functions and Algorithms manual for a detailed
description.
Use Tagname.Parameter for tagged points where Tag name can be up to 16 characters and the
permissible character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters, and must be a legitimate parameter name.

PIUOTDCF (STI, LLMUX, RHMUX)


Type:
Lock:
Default:
PtRes:

Logical
Eng/View
On
HPM

Open Thermocouple Detection EnableDefines whether the point is to detect


an open thermocouple condition. This parameter is configurable for each STI
point that is connected to a smart temperature transmitter and for each LLMUX
point.
NOTE: There is no special point type for RHMUX. The LLMUX point type
also applies to the RHMUX IOP.
This parameter is a view-only parameter when the point execution state
PTEXECST is Active.

Range:

R610
11/99

On (Detect an open thermocouple condition)


Off (Do not detect an open thermocouple)

HPM Parameter Reference Dictionary


Honeywell Inc.

299

PIUOTDCF(1)(168) (LLAI)

PIUOTDCF(1)(168) (LLAI)
Type:
Lock:
Default:
PtRes:
Range:

Logical
LLAI Open Sensor Detection EnableDefines whether an
open-sensor condition is to be detected for all eight LLAI points.
Supr
On
HPM
On (Detect open-sensor conditions)
Off (Do not detect open-sensor conditions)

PKGOPT (HPM Box)


Type:
Lock:
Default:
PtRes:

E:$PKGOPT
PtBld
REDUN_2F
HPM

Range:

1-REDUN (HPMMs in two 7-slot files/can have up to 40 IOPs)


2-REDUN_2F (HPMMs in two 15-slot files/can have up to 40 IOPs)
3-REDUN_IO (HPMMs/two separate 15-slot files/can have full redundant IOPs)
4-NODEFALT (Sets file/card positions of IOPs to 0. Used to bypass all defaults for IOP
File/Card positions).

HPMM Hardware Packaging Option. The tables below show the default
hardware location for each choice.

Helpful Hints: Parameter NODENUM must be equal to an odd number no matter which option is
selected for PKGOPT.
During Node Specific configuration, if you choose Redun_IO, you must type in file and card numbers for
the IOP cards. Refer to the tables below or the HPM Node Specific Configuration Form if necessary.
An HPMM can be operated as a non-redundant node independent of the PKGOPT selected.

The options are illustrated or discussed further in the following pages:

300

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PKGOPT (HPM Box)

REDUN
Right File

Left File
H
P
M IOP Cards
M
1&2

H
P
M IOP Cards
M

3 - 7

9&10

11 - 15

The Primary and Secondary HPMM Cards must be in Left File Card slots 1 & 2
and Right Card File, Card slots 9 & 10.
File 2

File 3

IOP Cards

IOP Cards

1 - 15

1 - 15

The File and Card position of the IOPs are defaulted as follows:
Hardware
IOM-A 1-5
IOM-A 6-10

File
1
1

Card Slot
3-7
11 - 15

Hardware
IOM-A 11- 25
IOM-A 26-40

File
2
3

Card Slot
1 - 15
1 - 15

NOTE
To operate the HPMM as non-redundant, configure PKGOPT = REDUN as above but install only one
of the HPMM card sets above. The backplane slot positions vacated by the second HPMM cards can
be used to house IOP cards if necessary.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

301

PKGOPT (HPM Box)

REDUN_2F
File 1
H
P
M
M
1&2

File 2

File 3

IOP Cards

H
P
M
M

IOP Cards

IOP Cards

3 - 15

1&2

3 - 15

1 - 14

The Primary and Secondary HPMMs must be in File 1, Card slots 1 & 2 and in File 2, Card Slots
1 & 2.
File and Card positions of the IOPs are defaulted as follows:
Hardware
IOM-A 1 - 13
IOM-A 14 - 26
IOM-A 27 - 40

File
1
2
3

Card Slot
3 - 15
14 - 26
1 - 14

NOTE
To operate the HPMM as non-redundant, configure PKGOPT = REDUN_2F as above but install only
one of the HPMM card sets above. The backplane slot positions vacated by the second HPMM cards
can be used to house IOP cards if necessary.

302

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PKGOPT (HPM Box)

REDUN_IO
File 1
H
P
M
M
1&2

File 3

File 2

IOP Cards

H
P
M
M

IOP Cards

IOP Cards

3 - 15

1&2

3 - 15

1 - 15

File 4

File 5

File 6

IOP Cards

IOP Cards

IOP Cards

1 - 15

1 - 12

1 - 12

The Primary and Secondary HPMMs must be in File 1, Card Slots 1 & 2 and in File 2, Card
Slots 1 & 2.
The File and Card position of the IOPs are defaulted as follows:
Hardware
IOM-A 1-13
IOM-A 14-28
IOM-A 29-40

File
1
3
5

Card Slot
3 - 15
1 - 15
1 - 12

Hardware
IOM-B 1 - 13
IOM-B 14 - 28
IOM-B 29 - 40

File
2
4
6

Card Slot
3 - 15
1 - 15
1 - 12

Note that on download of this configuration to the HPM, the PKGOPT is changed back to
REDUN_2F.

NODEFALT
The HPMM File(s) may be like any of the previous three configurations and up to 40 IOPs are
allowed. The IOP file/Card positions must be configured by the user. Note that on download to
the HPM, PKGOPT changes to REDUN, or REDUN_2F based on the actual hardware.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

303

PMEVOVFL

I/O Simulator Option


The optional I/O Simulator can be used to build points for this (the host) HPM or another HPM.
When using the I/O Simulator personality you may choose a packaging option (PKGOPT) that is
different from the physical backplane/hardware configuration of the host HPMM. The intent is
to let you choose a PKGOPT based on either the host's hardware configuration or that of another
HPMM. This allows you to create databases for other HPMs using a single HPM I/O Simulator
independent of its actual physical configuration. The following rules apply:
Host HPM
Configuratio
n
Any
Any

Other HPM
Configuration
7 - Slot
15 - Slot

PKGOPT
Selection
REDUN or NODEFALT
REDUN_2F, REDUN_IO, or NODEFALT

PMEVOVFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
View

HPMM Event Overflow Flag

HPM
Off (No overflow)
On (Overflow has occurred)

PMMCHAER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

HPMM I/O Link Channel A Error Count

PMMCHASL (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

304

Integer
View
0
HPM
>0

HPMM I/O Link Channel A Silence Count

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PMMCHBER (HPM Box)

PMMCHBER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

HPMM I/O Link Channel B Error Count

PMMCHBSL (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

HPMM I/O Link Channel B Silence Count

PMMCMD (HPM Box)


Type:
Lock:
Default:
PtRes:

E:$PMMCMD
OnProc
None
HPM

HPMM Command

NOTE
When points are built to a NIM and the NIM is restarted with no database, the points need
to be reloaded from checkpoint or the points must be reconfigured. If the database is to
be reconfigured, the HPMM must be in Idle, and the point execution state must be Inactive. This
allows the point build operation to override the database that already exists there.

Range:

R610
11/99

0-None (No command request has been issued)


1-Run (To "Run" state for processing points)
2-Idle (To "Idle" state for reloading the database)
3-RsIoLCom (Reset I/O Link communication error count = 0)
4-ShutDown (To "Alive" state for reloading personality)
5-RsUcnLsb (Reset the Local Statistics Block to zeroes)
6-SelChnA (Select Input/Output Link Channel A)
7-SelChnB (Select Input/Output Link Channel B)
8-Warmstrt (Warm Start)
9-Coldstrt (Cold Start)
10-SwapPri (Switchover to the redundant HPMM)

HPM Parameter Reference Dictionary


Honeywell Inc.

305

PMMCOMER (HPM Box)

PMMCOMER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$IOMCOMM
HPMM I/O Link Communication Error Status
View
N/A
HPM
0-None (No communication errors)
1-InvAlert (Invalid Alertmessage bit problem)
2-InvDest (Invalid Destination)
3-InvChCnt (Invalid Character Count)
4-InvSourc (Invalid Source)
5-InvCmd (Invalid Command)
6-Checksum (Data record Checksum Error)
7-No_Resp (No Response)
8-ChTimOut (Channel Time Out)
9-MsgOvRun (Message Overrun)
10-GapError (Message gap is too long)
11-LpBckErr (Loop Back Error)
12-NTH_0 (Next Token Holder equals zero)
13-TknRecov (Token Recovery in progress)
14-RplBufOv (Reply Buffer Overflow)

PMMCTLST (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Logical
HPMM Control Processor Status
View
Off
HPM
Off (Control processor has not failed)
On (Control processor has failed)

PMMIOLST (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

306

E:$IOMSTS
View
HPM
Notconfg (IOP not configured)
Confgmis (Configuration mismatch detected)
OK (Module is running with no soft fail errors)
Idle (Module is idle with no soft fail errors)
Softfail (Module is running with soft fail error(s) present)
Idlesf (Module is idle with soft failure error(s) present)
Nonexist (Module does not exist at this address)
Noresp (No response from module)
Poweron (Module state is Power On)
Commerr (Communication error to IOP)
Unavail (Module is unavailable for communication)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PMMOPER (HPM Box)

PMMOPER (HPM Box)


Type:
Lock:

E:$OPERATE
View

Process Manager Module OperationIndicates the type of HPMM.

Default: N/A
PtRes: HPM
Range: 0-NonRedun (This HPMM has no redundant HPMM to back it up)
1-Primary (This HPMM is the primary point processor)
2-Secondry (This HPMM is the secondary HPMM that backs up the primary HPMM)

PMMRECCH (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$RECCHN
HPMM I/O Link Current Receive Channel
View
N/A
HPM
0-ChannelA (Channel A is channel currently receiving)
1-ChannelB (Channel B is channel currently receiving)

PMMRECHN
Type:
Lock:
Default:
PtRes:
Range:

E:$RECCHN
View
N/A
HPM
ChannelA
ChannelB

HPMM Active Receive Channel

PMMSFST(1)(96)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
View

HPMM Soft Failure

HPM
Off
On

HPM Parameter Reference Dictionary


Honeywell Inc.

307

PMMSTS (HPM Box)

PMMSTS (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$NODESTA HPMM Primary Status


View
N/A
HPM
0-OffNet (NIM cannot communicate with the HPMM)
1-ConfgMs (Configuration mismatch detected)
2-Idle (Event reports but no point processing)
3-IdleSF (Soft failure occurred in Idle state)
4-OK (HPMM is operating normally)
5-SoftFail (Soft failure while HPMM is running)
6-Fail (HPMM can be accessed but CPU is halted; box hard failure has been detected )
10-Alive (No event reports or point processing)
11-AliveSF (Soft failure during Idle state)
12-Test (HPMM is in the test mode)
13-TestSF (Soft failure has been detected while the HPMM is in the test mode)
15-Loading (Personality or data base is loading)
16 S_Idle (Idle in Simulation Mode)
17 S_IdleSf (IdleSF in Simulation Mode)
18 S_OK (OK in Simulation Mode)
19 S_SFFail (SoftFail in Simulation Mode)
20 S_Pause (HPM is in the Simulation Pause state)
Standby
StandbySF
Upgrade
UpgradeSF
Helpful Hint: Loading the HPMM's operating personality software requires PMMSTS = Alive.
Loading the HPMM's database requires PMMSTS = Idle. Use parameter
PMMCMD's "Shutdown" and "Idle" command requests, respectively.

PNAMIOPA
Type:
Lock:
Default:
PtRes:
Range:

308

String_16
View
Parameter_Invalid
IOP

Physical Node Name Assigned to IOP A Returns the fieldbus


physical node name assigned to IOPA.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PNAMIOPB

PNAMIOPB
Type:
Lock:
Default:
PtRes:
Range:

String_16
View
Parameter_Invalid
IOP

Physical Node Name Assigned to IOP B Returns the fieldbus


physical node name assigned to IOPB.

PNTFORM
Type:
Lock:
Default:
PtRes:
Range:

E:$PNTFORM
Point FormDefines the form of the data point that is implemented.
Refer to the HPM Control Functions and Algorithms manual for a detailed
View/PB
description of this function.
Full
HPM
0-Full (Point is fully displayed and alarmed)
1-Componnt (Point is partially displayed but not alarmed)
Helpful Hint: This parameter is not applicable to DigOut points. For unconfigured DigIn and
AnalogOut points (used for Hardware Reference Addressing, the default value is
Component.

PNTFORM (FBCM, PECM, SECM)


FF Param. Source:
None
Type:
E:$PNTFORM
Point FormDefines the form of the data point that is implemented.
Lock:
PtBld
Default: Full
PtRes: IOP
Range: 0-Full (Point is fully displayed and alarmed. PNTFORM is always Full for SECM and PECM.)
1-Componnt (Point is partially displayed but not alarmed)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

309

PNTMODTY

PNTMODTY
Type:
Lock:
Default:
PTRes:
Range:

E:$UPCDTY
Point's Module TypeDefines where the data point resides. Control points
such as DigComp, RegPV, RegCtl, Logic, Process Module, Array, Box
View
Flags, Box Numerics, and Box Timers reside in the HPMM.
N/A
NIM
AO (Analog Output)
AO_16 (Analog Output/high density)
DI (Digital Input)
DO (Digital Output)
DO_32 (Digital Output/high density)
FBUS (Fieldbus)
HLAI (High-Level Analog Input)
LLAI (Low-Level Analog Input)
STIM(Smart Transmitter Interface)
NotConfg (Not Configured)
PI (Pulse Input)
HPMM (High-Performance Process Manager Module)
LLMUX (Low-Level Analog Input Multiplexer) All references to LLMUX also apply to
RHMUX, except that RHMUX does not support SENSRTYP of RTD.
DISOE (Sequence of Events)
SI (Serial Interface)
AO_16 (Analog Output 16)
DO_32 (Digital Output 32)

PNTNODTY
Type:
Lock:
Default:
PtRes:
Range:

E:$UCNNDTY Point's Node TypeDefines the type of node on the UCN


View
N/A
NIM
NIM (Network Interface Module)
HPM (High-Performance Process Manager)
NotConfg (Node not configured)

PNTSTATE
Type:
Lock:
Default:
PtRes:
Range:

310

E:PNTSTATE Point's Overall StateDefines the state of the data point, which is based on
the state of the HPMM and the IOP Card in which it resides.
View
N/A
NIM
Failed (NIM cannot communicate with point's HPMM/IOP)
Idle (Point's HPMM or IOP is in the Idle State)
OK (Point's HPMM or IOP is the Run State and is OK)
UNCERTN (Point's HPMM or IOP state is uncertain)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PNTTYPE

PNTTYPE
Type:
Lock:
Default:
PtRes:
Range:

E:PNTTYPE
Point TypeDefines the type of point in the HPM.
PtBld
Null
HPM
0-Null (Not configured)
1-AnalgIn (Analog Input)
2-AnalgOut (Analog Output)
4-DigIn (Digital Input)
5-DigOut (Digital Output)
6-DigCom (Digital Composite)
8-RegPV (Regulatory PV)
9-RegCtl (Regulatory Control)
10-Logic (Logic)
11-Array (Array)
12-Flag (Flag)
13-Numeric (Numeric)
14-ProcModl (Process Module)
22-Timer (Timer)
28-DevCtl (Device Control)
51-CM (Control Module)

Helpful Hint: PNTTYPE of DigOut has a restriction that PNTFORM cannot be = Full.

POSITION (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$POSITIN
HPMM File Position
View
N/A
HPM
0-Right (HPMM cards are in card file slots 610)
1-Left (HPMM cards are in card file slots 15)
2-File_1 (HPMM cards are in card file 1)
3-File_2 (HPMM cards are in card file 2)
4-Pref
5-Non_Pref
6-None
7-Unknown (Not able to determine file position from hardware)

HPM Parameter Reference Dictionary


Honeywell Inc.

311

PR2PREFF (HPM Box)

PR2PREFF (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
100
HPM
0 - 100

Peer-to-Peer Communication Efficiency (in percent)Indicates the rate of


successful and on time UCN transactions from this node.

Helpful Hint: This statistic is displayed on the Control Configuration page of the HPM
Diagnostic Display.

PRGATRFL (DigComp, DevCtl, RegCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Program Mode Attribute Flag indicates if the point is in Program Mode
attribute.
View
N/A
HPM
On - (point is in Program mode attribute)
Off - (point is not in Program mode attribute)

PRILNKMS (SECM)
FF Param. Source:
NMIB: PrimaryLinkMasterFlagVariable
Type:
Logical
PrimaryLinkMasterTRUE = IOP Device will be the Primary Link
master. The configuration tool (TPSB) MUST make sure that ONLY
Lock:
PtBld/Engr
one device per link should have this.
Default: FALSE
PtRes: IOP
Range: TRUE / FALSE

312

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PRIMMOD

PRIMMOD
Type:
Lock:
Default:
PtRes:

Ent_Id
Engr
Null
NIM

Primary Module Point IdentifierTypically used in Batch Processing, this


parameter contains the tag name of an HPM point to which this data point is
assigned. Other points that belong to the Batch equipment unit should have their
PRIMMOD set to this same point. Primmod is used to collect alarms and events
from this point along with others related to the specified Primary Module point.
Information is collected into a common file, accessible from the Event History
Menu.

Range:

Tag name of the process module point can be up to 16 characters, and the permissible character set is as
follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive underscores are
not allowed.
Embedded space characters are not allowed.
Helpful Hint: For Box Flag points, this parameter applies to only slots 1 through 128.
TPS network entities that can be stored to PRIMMOD in NIM points are restricted to local NIM points.

PRMDESC(1)(12) (Logic)
Type:
Lock:
Default:
PtRes:
Range:

E:$PMMLGPM
Parameter Descriptor AssignmentDefines up to 12 logic-slot
parameters to which custom generic descriptors entered through
Eng/PB
parameters GENDESC(1-12) are to be assigned.
N/A
NIM
L1...L12 (Logic-slot inputs)
FL1...FL12 (Logic-slot flags)
NN1...NN8 (Logic-slot numerics)
SO1...SO24 (Logic-slot outputs)

PROCMOD (ProcMod)
Type:
Lock:

E:PROCMOD
Process Module Operating StateRepresents the operational condition
of a process module. Refer to the HPM Control Functions and
Determined by
Algorithms manual for a state diagram.
CNTLLOCK
parameter
Default: Off
PtRes: HPM
Range: 0-Off (Off)
2-Norm (Normal)
4-Hold (Hold)
5-Shdn (Shutdown)
6-Emsd (Emergency Shutdown)
7-Strt (Start)
8-Stop (Stop)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

313

PRPMMSTS

PRPMMSTS
Type:
E:$NODESTA
Lock:
View
Default:
PtRes: HPM
Range:

314

Previous HPMM Status

Offnet (HPMM is offnet with no communications possible)


Confgmis (HPMM is in configuration mismatch)
Idle (HPMM is idle)
Idlesf (HPMM is idle with soft failure(s))
OK (HPMM is running with no errors)
Softfail (HPMM is running with soft failure(s))
Fail (HPMM has failed)
Poweron (HPMM is in Power On state-startup condition from power loss)
Alive (HPMM has passed self diagnostics and is ready to accept personality)
Alivesf (HPMM diagnostics have soft failure)
Loading (HPMM is loading personality)
Notconfg (HPMM is not configured on network)
Unavail (HPMM is unavailable on network for communications)
Test (HPMM is in Test mode)
Testsf (HPMM is in Test mode with a soft failure(s))
Standby
StandbySF
Upgrade
UpgradeSF

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PRVCOMFL

PRVCOMFL
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$PMMHFST
View

Previous HPMM Communications Board Failure

HPM
NULL (Unknown Error)
PWRDWN (Power is Off)
LR_PAR (Local Ram Parity Error)
LR_LRAM (Local Ram Error)
LR_CK (Local Ram Check)
LR_EXC (Local Ram Exception )
LR_HREV (Local Ram Hardware Revision)
MM_HREV (Memory Board Hardware Revision)
LR_TMR (Local Ram Timer Error)
LR_PTRN (Local Ram Pattern Check Error)
LR_BYTE (Local Ram Byte Error)
LR_ADCD (Local Ram Address Decode Test)
LR_ADDL (Local Ram Additional Checks)
LR_CLRR (Local Ram Scrub Incomplete)
SR_PAR (Shared Ram Parity)
SR_PTRN (Shared Ram Pattern)
SR_ADCD (Shared Ram Address Decode Test)
SR_ADDL (Shared Ram Additional Checks)
GR_PAR (Global Ram Parity)
GR_PTRN (Global Ram Pattern Check Error)
GR_BYTE (Global Ram Byte Error)
GR_ADCD (Global Ram Address Decode Test)
GR_ADDL (Global Ram Additional Checks)
GR_CLRR (Global Ram Scrub Incomplete)
31_NR (IOL Processor, No Response or Failure)
31_ALIV (IOL Processor, Transmitter Not Alive)
31_ILTN (IOL Processor, Illegal Transition)
NMI_UNK (Unknown NMI Request)
BADUCNN (UCN Address Parity or Duplicate Address)
NR (No Response From Other Processor)
MRFT (Memory Reference Table - Pattern Build Fail)
NOMTOS (No MTOS Readout)
LLC_COMM (LLC Communication Fatal Error)
UCNDRV (UCN Driver, Fatal Error)
RD_HREV (Redundancy Card Version/Revision Mismatch)
SW_ERROR (Software Error)
MD_HREV (Modem Card Version/Revision Mismatch)
DA_PTRN (Daughter Card Pattern Test)
DA_BYTE (Daughter Card Byte Write Test)
DA_ADCD (Daughter Card Address Decode)
DA_ADDL (Daughter Card Additional Tests)
DA_CLRR (Daughter Card Scrub Incomplete)
RD_SNPS (Redundancy Card 96 Kw Snapshot Error)
RD_BSLK (Redundancy Card Bus Lock Fail)

HPM Parameter Reference Dictionary


Honeywell Inc.

315

PRVCTLFL

PRVCTLFL
Type:
E:$PMMHFST
Lock:
View
Default:
PtRes: HPM
Range:

316

Previous HPMM Control Failure

NULL (Unknown Error)


PWRDWN (Power is Off)
LR_PAR (Local Ram Parity Error)
LR_LRAM (Local Ram Error)
LR_CK (Local Ram Check)
LR_EXC (Local Ram Exception )
LR_HREV (Local Ram Hardware Revision)
MM_HREV (Memory Board Hardware Revision)
LR_TMR (Local Ram Timer Error)
LR_PTRN (Local Ram Pattern Check Error)
LR_BYTE (Local Ram Byte Error)
LR_ADCD (Local Ram Address Decode Test)
LR_ADDL (Local Ram Additional Checks)
LR_CLRR (Local Ram Scrub Incomplete)
SR_PAR (Shared Ram Parity)
SR_PTRN (Shared Ram Pattern)
SR_ADCD (Shared Ram Address Decode Test)
SR_ADDL (Shared Ram Additional Checks)
GR_PAR (Global Ram Parity)
GR_PTRN (Global Ram Pattern Check Error)
GR_BYTE (Global Ram Byte Error)
GR_ADCD (Global Ram Address Decode Test)
GR_ADDL (Global Ram Additional Checks)
GR_CLRR (Global Ram Scrub Incomplete)
31_NR (IOL Processor, No Response or Failure)
31_ALIV (IOL Processor, Transmitter Not Alive)
31_ILTN (IOL Processor, Illegal Transition)
NMI_UNK (Unknown NMI Request)
BADUCNN (UCN Address Parity or Duplicate Address)
NR (No Response From Other Processor)
MRFT (Memory Reference Table - Pattern Build Fail)
NOMTOS (No MTOS Readout)
LLC_COMM (LLC Communication Fatal Error)
UCNDRV (UCN Driver, Fatal Error)
RD_HREV (Redundancy Card Version/Revision Mismatch)
SW_ERROR (Software Error)
MD_HREV (Modem Card Version/Revision Mismatch)
DA_PTRN (Daughter Card Pattern Test)
DA_BYTE (Daughter Card Byte Write Test)
DA_ADCD (Daughter Card Address Decode)
DA_ADDL (Daughter Card Additional Tests)
DA_CLRR (Daughter Card Scrub Incomplete)
RD_SNPS (Redundancy Card 96 Kw Snapshot Error)
RD_BSLK (Redundancy Card Bus Lock Fail)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PRVIOLFL

PRVIOLFL
Type:
Lock:
Default:
PtRes:
Range:

E:$IOMHF
View

Previous IOL Failure

HPM
UNKNOWN (Unknown Error)
POWERDWN (Power is Off)
INVPRGEX (Invalid Program Execution)
EPROMERR (EPROM Error)
RAMCNTER (Ram Contents Error)
RAMADRER (Ram Address Error)
DPAERROR (Physical Address Error)
DSAERROR (Soft Address Error)
RXBUFOFL (Receive Buffer Overflow)
IOLJABER (IOL Jabber Circuit - saw too much traffic)
BADPGJMP (Bad Program Jump)
ADCINCMP (A/D Incomplete)
ADOUTOVF (A/D Output Overflow)
ADOUTUDF (A/D Output Underflow)
ADCCALER (A/D Calibration Error)
BADDCLTC (Bad DC LTC)
DMT_TMOT (Dead Man Time Out)
MLTOUTFL (Multiple Output Failure)
DATBUSFL (Data Bus Failure)
BADDARNG (Bad D/A Range)
MSTRTMOT (Master Time Out 68 K)
CTRCKTFL (Counter Circuit Failure)

PSDLYFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
Poststore Delayed FlagSet when poststore data is older than 1 second.
View
Off
HPM
Off
On (poststore data is older than 1 second.)

PSTS (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:PVVALST
Pressure Input Value StatusStatus of the P input value.
View
Normal
HPM
0-Bad (Value is bad and replaced with NaN)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

HPM Parameter Reference Dictionary


Honeywell Inc.

317

PTDATA

PTDATA
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: NIM
Range: N/A

None
This parameter set has been added for compatibility with fieldbus requirements.

PTDESC
Type:
Lock:
Default:
PtRes:
Range:

String_24
Point DescriptorA 24-character descriptor which is used to describe the point
and appears on the Group and Detail Displays for the point. Refer to
PtBld
Figure N-1.
Blank
NIM
Permissible character set consists of all characters on the Engineer' s Keyboard. Basically this set consists
of alphabetics A-Z, numerics 0-9, and the following special characters:
space ! % & ' ( ) * + - / : ; > < = ? _ , . $

PTEXECST
Type:
Lock:
Default:
PtRes:
Range:

E:PTEXECST Point Execution StateDefines the current execution state of the point.
Supr
Inactive
HPM
0-Inactive (Point is not scanned or processed)
1-Active (Point is scanned and processed)

PTINAL (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

318

Logical
Point in Alarm IndicatorIndicates when an alarm condition has been
detected at this point.
View
Off
HPM
Off (Point is not in alarm)
On (Point is in alarm)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PTORST (RegCtl)

PTORST (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ORSTATUS
Point Override StatusIndicates the override status of the point.
Prog
NotCon
HPM
0-NotCon (Not connected to ORSel algorithm. Also indicates that point has been returned from inactive
to active status, or it is undergoing a cold restart, or it is being initialized.)
1-Sel (Selected as a part of ORSel strategy)
2-NotSel (Not selected as a part of ORSel strategy)

PTSTSIOL
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$NODESTA Redundant Partner Status as Seen From the IOL


View
HPM
OffNet (NIM cannot communicate with the HPMM)
ConfgMis (Configuration mismatch detected)
Idle (Event reports but no point processing)
Idlesf (Soft failure occurred in Idle state)
Ok (HPMM is operating normally)
SoftFail (Soft failure while HPMM is running)
Fail (HPMM can be accessed but CPU is halted; box hard failure has been detected)
Powron (Power is on)
Alive (No event reports or point processing)
Alivesf (Soft failure during Idle state)
Test (HPMM is in the Test mode)
TestSF (Soft failure has been detected while the HPMM is in the Test mode)
Loading (Personality or database is loading)
Notconfg
Nosynch
Unavail
Standby
StandbySF
Upgrade
UpgradeSF

HPM Parameter Reference Dictionary


Honeywell Inc.

319

PTSTSUCN

PTSTSUCN
Type:
Lock:
Default:
PtRes:
Range:

E:$NODESTA Redundant Partner Status as Seen From the UCN


View
HPM
Offnet (NIM cannot communicate with the HPMM)
Confgms (Configuration mismatch detected)
Idle (Event reports but no point processing)
Idlesf (Soft failure occurred in Idle state)
Ok (HPMM is operating normally)
Softfail (Soft failure while HPMM is running)
Fail (HPMM can be accessed but CPU is halted; box hard failure has been detected)
Powron (Power is on)
Alive (No event reports or point processing)
Alivesf (Soft failure during Idle state)
Test (HPMM is in the Test mode)
Testsf (Soft failure has been detected while the HPMM is in the Test mode)
Loading (Personality or database is loading)
Notconfg
Nosynch
Unavail
Standby
StandbySF
Upgrade
UpgradeSF

PULSEWTH (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Pulse Width for Point Outputs


Real
Supr
1.0 second
HPM
0.0 to 60.0 seconds
Helpful Hint: PULSEWTH change requires DODSTN= "Tagname.ONPULSE" or OFFPULSE. When
On is to be written to the DigOut module, a pulse of the specified width is generated. When Off is to be
written, no pulse is generated.

PV (AnalgIn, PI)
Type:
Lock:
Default:
PtRes:
Range:

Process VariablePV is the PV's current value after the PV is selected from
Real
one of the following possible sources: a field device, an operator, or a program.
Oper
See PVSRCOPT and PVSOURCE.
NaN
HPM
PVEXEUHI to PVEXEULO,
NaN
Helpful Hint: PV change by a program requires PVSRCOPT = All and PVSOURCE = Sub.
PV change by an operator requires PVSRCOPT = All and PVSOURCE = Man.

320

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PV (DevCtl, DigComp)

PV (DevCtl, DigComp)
Current StatePV is the PV's current state after the PV is
E:SD_ENM:P
selected from one of the following possible sources: a field device,
VSTATES
an operator, a program, or the output of the PV's data point. See
Lock: Oper
PVSRCOPT and PVSOURCE.
Default: BADPVTXT
PtRes: HPM
Range: 0-PVSTATES (0) (Defined by STATETXT (0))
1-PVSTATES (1) (Defined by STATETXT (1))
2-PVSTATES (2) (Defined by BADPVTXT)
3-PVSTATES (3) (Defined by MOVPVTXT)
4-PVSTATES (4) (Defined by STATETXT(2))
Type:

Helpful Hint: PV change by a program requires PVSRCOPT = All and PVSOURCE = Sub.
PV change by an operator requires PVSRCOPT = All and PVSOURCE = Man.

PV (DigIn)
Current StateIndicates the current state of the PV input to
this data point. Not appropriate if DITYPE = ACCUM.
E:SD_ENM:S
TATETXT
Lock:
Oper
Default: Off
PtRes: HPM
Range: STATETXT(0) or STATETXT(1)
Type:

Helpful Hint: PV is derived from the open or closed state of field contacts and from the
configured direct or reverse input direction (INPTDIR).
PV change by a program requires DITYPE = Latched or status,
PVSRCOPT = All, and PVSOURCE = Sub.
PV change by an operator requires DITYPE = Latched or status,
PVSRCOPT = All, and PVSOURCE = Man.

PV (Flag)
Type:
Lock:
Default:
PtRes:
Range:

E:SD_ENM:STATETXT
Current StateIndicates the current state of the flag
Oper
data point, and it is derived from PVFL. STATETXT(1)
Blank
is the alarmed state.
HPM
STATETXT(0) or STATETXT(1)

PV (Numeric)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Oper
NaN
HPM
N/A

Process VariableIndicates the value of the numeric. This value maps into
parameter NN(n) in the HPM box where n = SLOTNUM.

HPM Parameter Reference Dictionary


Honeywell Inc.

321

PV (RegCtl, RegPV)

PV (RegCtl, RegPV)
Type:
Lock:

Real
View for
RegCtl,
Oper for
RegPV
Default: NaN
PtRes: HPM
Range: N/A

Process VariableIndicates the current value of the PV after the PV is selected


from one of the following possible sources: a field device, an operator, or a
program. See PVSRCOPT and PVSOURCE.

Helpful Hint: PV change by a program requires PVSRCOPT = All and PVSOURCE = Sub.
PV change by an operator requires PVSRCOPT = All and PVSOURCE = Man.

PV (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
0 to 32000

Current ValueIndicates the current time in seconds or minutes. The timer


starts at 0 and is incremented towards the preset time established by the SP
parameter.

PV (FBCM)
FF Param. Source:
Type:
Real
Lock:
Oper
Default: NaN
PtRes: IOP
Range: Floating Point
0-Off
1-On

AI: OUT.Value; DI: OUT_D.Value; PD: PV.Value; PID: PV.Value


Process VariableThe value of this parameter appears as a real number in the
FB IOP and on the UCN. For a DI CMTYPE, the value is translated to a logical
value by the NIM.

PVALDB (FBCM)
FF Param. Source:
Type:
E:PVALDB
Lock:
View
Default: 6-EU
PtRes: IOP
Range: None

322

None
PV Alarm DeadbandAlarm deadband is used to prevent excessive recurrence
of alarms by adjusting the percent of Engineering Unit range at which the alarm
"returns to normal." Value of this parameter is fixed to enumerated member to
force the use of PVALDBEU.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVALDB (RegCtl, RegPV)

PVALDB (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:PVALDB
PV Alarm DeadbandAlarm deadband is used to prevent excessive recurrence
Eng/PB
of alarms by adjusting the percent of Engineering Unit range at which the alarm
One
"returns to normal."
HPM
0-Half (1/2 of 1% of Engineering Unit range)
1-One (1% of Engineering Unit range)
2-Two (2% of Engineering Unit range)
3-Three (3% of Engineering Unit range)
4-Four (4% of Engineering Unit range)
5-Five (5% of Engineering Unit range)
6-EU (Specify deadband in Engineering Units)

PVALDBEU (FBCM)
FF Param. Source:
ALARM_HYS
EU Value of PV Alarm DeadbandAlarm deadband in engineering units.
Type:
Real
Lock:
Engr/PB
Default: NaN
PtRes: IOP
Range: 0 to 50% of range (range is PVEUHI minus PVEULO)

PVALDBEU (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng/PB
NaN
HPM
> 0.0

EU Value of PV Alarm deadbandAlarm deadband in engineering units.

PVALGID
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$PMMPVAG
PV Algorithm IdentifierDefines which PV algorithm is to be used for a
PtBld
RegPV point.
Null
HPM
0-Null (No algorithm configured)
1-DataAcq (Data Acquisition)
2-FlowComp (Flow Compensation)
3-MidOf3 (Middle-Of-3 Selector)
4-HiLoAvg (High Low Average Selector)
5-Summer (Summer)
6-VdtLdLag (Variable Dead Time with Lead Lag)
7-TotaLizr (Totalizer)
8-GenLin (General Linearization)
9-Calcultr (Calculator)

HPM Parameter Reference Dictionary


Honeywell Inc.

323

PVAUTO (AnalgIn, PI)

PVAUTO (AnalgIn, PI)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

PV Auto ValueValue of the PV after PVCALC is range checked, filtered, and


clamped.

PVAUTO (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

E:PVSTATES
Current PV StateIndicates the current PV state, based on the states of the
View
inputs to the point.
BADPVTXT
HPM
0-STATETXT(0)
1-STATETXT(1)
2-BADPVTXT
3-MOVPVTXT
4-STATETXT(2) (only if NOSTATES is 3)

PVAUTO (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

E:STATETXT Current PV StateIndicates the current PV state that corresponds to the


View
field contact input after direct/reverse correction.
N/A
HPM
STATETXT(0) or STATETXT(1)

PVAUTO (FBCM)
FF Param. Source:
AI: OUT.Value; DI: OUT_D.Value
Type:
Real
PV AutoValue of the PV after the OUT value is status-checked and
clamped. This value appears as a real number in the IOP and on the
Lock:
View
UCN. For the DI CMTYPE, the value is translated to a logical by the
Default: NaN, Off
NIM.
PtRes: IOP
Range: NaN
0-Off
1-On
PVEUHI plus 10% of span, PVEULO minus 10% of span (where span is absolute value of the
difference of (PVEUHI-PVEULO)

324

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVAUTO (RegCtl)

PVAUTO (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

PV Auto Value Fetched Using Control Input ConnectionIndicates the


current value of the PV when the RegCtl point is in the Auto mode.

PVAUTO (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

PV Auto ValueIndicates the current value of the PV after the algorithm


calculation is performed, the range is checked, and the PV is filtered and
clamped.

PVAUTOST (FBCM)
FF Param. Source:
AI: OUT_STATUS.Quality
Type:
E:PVVALST PVAUTO StatusStatus of PVAUTO parameter.
Lock:
View
Default: Bad
PtRes: IOP
Range: 0-BAD
1-UNCERTAIN
2-NORMAL

PVAUTOST (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:PVVALST
PV Auto Value StatusIndicates the current status of the PVAUTO value.
View
Bad
HPM
0-Bad (All inputs, or result in PVCALC is bad)
1-Uncertn (Final result in PVCALC is an uncertain value)
2-Normal (Final result in PVCALC is a normal value)

HPM Parameter Reference Dictionary


Honeywell Inc.

325

PVCALC (AnalgIn, PI)

PVCALC (AnalgIn, PI)


Type:
Lock:
Default:
PtRes:
Range:

Real
Calculated PVPVCALC is the PV value in Engineering Units after the raw
PV (PVRAW) input to this data point has been characterized. The value of
View
PVRAW is the PV value provided by the Field Termination Assembly (FTA).
NaN
HPM
PVEXEUHI to PVEXEULO,
NaN

PVCALC (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: IOP
Range: Floating Point

AI: FIELD_VAL.Value
PV Calculation PV value in EU after the field value has been
processed (converted, clamped, and filtered) by the function block. This
parameter is identical to the OUT.Value parameter.

PVCALC (RegPV)
Type:
Lock:
Default:
PtRes:
Range:

326

Real
View
NaN
HPM
N/A,
NaN

Calculated PVIndicates the value of the PV after the PV has been calculated
by the PV algorithm.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVCHAR

PVCHAR
Type:
Lock:
Default:
PtRes:

E:VALCHAR
PtBld
Linear
HPM

PV Characterization OptionDefines the display characterization to be


used for characterizing the input PV value. Characterization is based on the
field sensor type.

HLAI, LLMUX, RHMUX, & LLAI PV Characterization

Range

PNT
MODTY
(NOTE
1)

X = Allowable Sensor Type (SENSRTYP)


pt42V

02V

15V

0-100
mV

T
C

Slide
wire

R
T
D

Valid normal
range
(PVEULO
PVEUHI)
in Degrees C
(when TCRNGOPT
= Normal for
SENSRTYP =
Thermcpl

Valid extended
range
(PVEXEULO
PVEXEUHI)
in Degrees C
(when TCRNGOPT
= Extended for
SENSRTYP =
Thermcpl)

HLAI
X
X
X
-200 to 1200
N/A
LLAI
X
-100 to 750
-200 to 1200
LLMUX
X
-100 to 750
-200 to 1200
HLAI
X
X
X
0 to 1100
-200 to 1370
1-Ktherm
LLAI
X
0 to 1100
-200 to 1370
LLMUX
X
0 to 1100
-200 to 1370
HLAI
X
X
X
-200 to 1000
N/A
2-Etherm
LLAI
X
-150 to 500
-200 to 1000
LLMUX
X
-150 to 500
-200 to 1000
HLAI
X
X
X
-230 to 400
N/A
3-Ttherm
LLAI
X
-200 to 300
-230 to 400
LLMUX
X
-200 to 300
-230 to 400
HLAI
X
X
X
100 to 1820
N/A
4-Btherm
LLAI
X
600 to 1650
100 to 1820
LLMUX
X
600 to 1650
100 to 1820
HLAI
X
X
X
0 to 1700
N/A
5-Stherm
LLAI
X
550 to 1500
0 to 1700
LLMUX
X
550 to 1500
0 to 1700
HLAI
X
X
X
0 to 1700
N/A
6-Rtherm
LLAI
X
550 to 1500
0 to 1700
LLMUX
X
550 to 1500
0 to 1700
HLAI
X
X
X
0 to 1700
N/A
7-RPtherm
LLAI
X
550 to 1500
0 to 1700
LLMUX
X
550 to 1500
0 to 1700
HLAI
X
X
X
-180 to 800
N/A
8-DinRtd
LLAI
X
-200 to 850
N/A
LLMUX
X
-200 to 850
N/A
HLAI
X
X
X
-180 to 650
N/A
9-JisRtd
LLAI
X
-200 to 650
N/A
LLMUX
X
-200 to 650
N/A
HLAI
X
X
X
-45 to 315
N/A
10-NicklRtd
LLAI
X
-45 to 315
N/A
LLMUX
X
-45 to 315
N/A
X
X
X
-20 to 250
N/A
11-CopprRtd HLAI
LLAI
X
-20 to 250
N/A
LLMUX
X
-20 to 250
N/A
HLAI
X
X
X
X
N/A
N/A
12-Linear
LLAI
X
X
X
N/A
N/A
LLMUX
X
N/A
N/A
HLAI
X
X
X
N/A
N/A
13-Sqrroot
LLAI
X
X
N/A
N/A
N/A = Not Applicable
NOTE 1: PNTMODTY LLMUX includes RHMUX for all thermocouple types except RTD; RTD type is not supported
by RHMUX IOP.
0-Jtherm

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

327

PVCHAR

STI PV Characterization
(Pressure and Magnetic Flow Transmitters)
Range

Spt_Dp

Spt_Gp

Spt_Ap

Sfm

Linear

Sqrroot

--

--

--

X = Allowable Sensor Type

STI PV Characterization (Temperature Transmitters)

Range

Normal Range
(PVEULO to PVEUHI)
in Degrees C (except
where noted)

Linear
1000 mV

Maximum Range
(PVEXEULO to PVEXEUHI)
in Degrees C (except
where noted)

-50 to 220 mV

-1000 to

Thermocouples
Btherm

400 to 1820

200 to 1820

Etherm
Jtherm
Ktherm
NiNiMoTC
Ntherm
Rtherm
Stherm
Ttherm
W3W25TC
W5W26TC

-100 to 1000
-180 to 1200
-170 to 1250
600 to 1300
-100 to 1300
0 to 1760
0 to 1760
-120 to 400
0 to 2300
0 to 2300

-200 to 1000
-200 to 1200
-200 to 1370
600 to 1300
-200 to 1300
-50 to 1760
-50 to 1760
-250 to 400
0 to 2300
0 to 2300

-20 to 250
-20 to 250
-200 to 450
-200 to 450
-200 to 450
-200 to 450
420 to 1800

-20 to 250
-20 to 250
-200 to 850
-200 to 640
-200 to 850
-200 to 850
700 to 1800

0 to 4K`

0 to 4K`

RTDs
Cu10RTD
Cu25RTD
Pt100 DinRtd
Pt100 JisRtd
Pt200 RTD
Pt500 RTD
RH Rad
RTD Ohms

328

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVCHAR (FlowComp)

PVCHAR (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

E:VALCHAR
PV Characterization OptionDefines the display characterization to be
PtBld
used for characterizing the input PV value of Regulatory PV point configuring
SqRoot
with Flow Compensation.
HPM
12-Linear (The COMPTERM compensation is not square rooted)
13 SqRoot (The COMPTERM compensation is square rooted)

PVCHGDLY
Type:
Lock:
Default:
PtRes:

Integer
Supr
0 seconds
HPM

Range:

0 to 60 seconds

PV Change Delay time in SecondsDefines the time(in seconds) that a


point with a previously detected PV change event is guaranteed to remain at
the new value even if the PV returns to its original value. If the point remains
at its new value when the delay timer expires, the point is held at the new
value.

Helpful Hint: PVCHGDLY requires that EVTOPT = EIP, SOE, or EIPSOE.

PVCLAMP
Type:
Lock:
Default:
PtRes:

E:PVCLAMP
Eng/PB
NoClamp
HPM

PV Clamping OptionDefines whether PV clamping is to be used for this


data point. If PVCLAMP = Clamp and the PV extended range is exceeded,
PV value status PVSTS is marked Uncertain and the PV is set equal to the
extended limit that was violated.

Range:

0-NoClamp (No clamping of the PV value)


1-Clamp (Clamp PV value at range extension limit)

PVEQN (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
PV Equation TypeDefines the equation type (EqA-EqE) to be used for this
PtBld
PV algorithm. Refer to the HPM Control Functions and Algorithms manual
EqA
for more information.
HPM
Comp. Inputs
Type of Compensation
0-EqA
G
Mass/Volumetric flow of liquid
1-EqB
P and T
Mass flow of gases and vapors
2-EqC
G, P, and T
Mass flow of gases and vapors w/specific gravity
3-EqD
G, P, and T
Volumetric flow of gases and vapors
4-EqE
P, T, X, and Q
Mass flow of steam

G = measured or calculated specific gravity or molecular weight, P = measured actual gage pressure, T = measured
actual temperature, X = measured actual steam compressibility and Q = measured actual steam quality.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

329

PVEQN (HiLoAvg)

PVEQN (HiLoAvg)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN PV Equation TypeDefines the equation type (EqA-EqC) to be used for this
Eng/PB
PV algorithm. Refer to the HPM Control Functions and Algorithms manual
EqA
for more information.
HPM
0-EqA (Select and identify highest of up to six inputs)
1-EqB (Select and identify lowest of up to six inputs)
2-EqC (Calculate the average of up to six inputs)

PVEQN (MidOf3)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
PV Equation TypeDefines the equation type (EqA-EqC) to be used for this
PV algorithm. Refer to the HPM Control Functions and Algorithms manual
Eng/PB
for more information.
EqA
HPM
0-EqA (Highest good input when one or two are bad)
1-EqB (Lowest good input when one or two are bad)
2-EqC (Average of all good inputs)

PVEQN (Summer)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
PV Equation TypeDefines the equation type (EqA or EqB) to be used for
this PV algorithm. Refer to the HPM Control Functions and Algorithms
PtBld
manual for more information.
EqA
HPM
0-EqA (P1 input is scaled and biased)
1-EqB (Up to six inputs are scaled and summed with an overall bias applied)

PVEQN (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

330

E:ALGOEQN
PV Equation TypeDefines the equation type (EqA-EqF) to be used for this
PV algorithm. Refer to the HPM Control Functions and Algorithms manual
Eng/PB
for more information.
EqA
HPM
Option
Warm Restart Action
Bad Input Handling
0-EqA
Continue
Use zero
1-EqB
Continue
Use last good value
2-EqC
Continue
Set Bad and stop
3-EqD
Set Bad, and stop
Use zero
4-EqE
Set Bad, and stop
Use last good value
5-EqF
Set Bad, and stop
Set Bad and stop

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVEQN (VdtLdLag)

PVEQN (VdtLdLag)
Type:
Lock:
Default:
PtRes:
Range:

E:ALGOEQN
PV Equation TypeDefines the equation type (EqA-EqD) to be used for this
PV algorithm. Refer to the HPM Control Functions and Algorithms manual
PtBld
for more information.
EqA
HPM
0-EqA (Lead-Lag)
1-EqB (Fixed dead time)
2-EqC (Variable dead time)
3-EqD (Variable dead time with two lags)
Helpful Hint: For Equations C and D, the dead time is changed in steps of NLOC*NRATE*TS
where NLOC is configurable from 2 to 30, for better resolution of dead time.

PVEUHI
Type:
Lock:
Default:
PtRes:
Range:

Real
PV High Range in Engineering UnitsNote that PVEUHI cannot be written
with NaN. NaN is the default value only.
Eng
NaN
HPM
PVEULO to PVEXEUHI, NaN
Helpful Hint: For Smartline transmitters, refer to Table A-3 in the PM/APM Smartline Transmitter
Integration Manual.

PVEUHI (FBCM)
FF Param. Source:
AI: OUT_SCALE.EU100; PID: PV_SCALE.EU100
Type:
Real
PV High Range in Engineering Units
Lock:
Engr
Default: 100
PtRes: IOP
Range: PVEULO to PVEXEUHI, NaN

PVEULO
Type:
Lock:
Default:
PtRes:
Range:

Real
PV Low Range in Engineering UnitsNote that PVEULO cannot be written
with NaN. NaN is the default value only.
Eng
NaN
HPM
PVEXEULO to PVEUHI, NaN
Helpful Hint: For Smartline transmitters, refer to Table A-3 in the PM/APM Smartline Transmitter
Integration Manual.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

331

PVEULO (FBCM)

PVEULO (FBCM)
FF Param. Source:
AI: OUT_SCALE.EU0; PID: PV_SCALE.EU0
Type:
Real
PV Low Range in Engineering Units PV Low Range in
Engineering Units.
Lock:
Engr
Default: 0
PtRes: IOP
Range: PVEXEULO to PVEUHI, NaN

PVEXEUHI
Type:
Lock:
Default:
PtRes:
Range:

Real
PV Extended Engineering Unit Range HighBoth PVEXEUHI and
PVEXEULO are used to clamp or detect a bad PV value. Refer to parameter
Engr
PVEXEULO. Note that PVEXEUHI cannot be written with NaN. NaN is the
NaN
default value only.
HPM
> PVEUHI, NaN

PVEXEUHI (FBCM)
FF Param. Source:
None
Type:
Real
PV Extended Engineering Unit Range High.
Lock:
Engr
Default: NaN
PtRes: IOP
Range: >= PVEUHI, NaN

PVEXEULO
Type:
Lock:
Default:
PtRes:

Range

Real
Engr
NaN
HPM

PV Extended Engineering Unit Low RangeFor the LLAI IOP with


Thermocouple and RTD sensor types, extended PV range parameters are VIEW
ONLY. Their values are defaulted based on the sensor types, the thermocouple
range option, and temperature scale. The tables below show the default values in
degrees C. For other engineering units, these values are appropriately converted.
Note that PVEXEULO cannot be written with NaN. NaN is the default value
only.
< PVEULO, NaN

Defaults for Extended Range PV Parameters When SENSRTYP = THERMCPL, PVTEMP = Degrees C

PVCHAR
Btherm
Etherm
Jtherm
Ktherm
Rtherm
RPtherm
Stherm
Ttherm

332

TCRNGOPT = NORMAL
PVEXEULO
PVEXEUHI
600
1650
-150
500
-100
750
0
1100
550
1500
550
1500
550
1500
-200
300

TCRNGOPT = EXTENDED
PVEXEULO
PVEXEUHI
100
1820
-200
1000
-200
1200
-100
1370
0
1700
0
1770
0
1700
-230
400

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVEXEULO (continued)

PVEXEULO (continued)
Defaults for Extended Range PV Parameters When SENSRTYP = RTD, PVTEMP = Degrees C

PVCHAR

PVEXEULO

PVEXEUHI

PtDinRTD
PtJisRTD
NicklRTD
CopprRTD

-180
-180
-45
-20

800
650
315
250

PVEXEULO (FBCM)
FF Param. Source:
None
Type:
Real
PV Extended Engineering Units Low Range
Lock:
Engr
Default: NaN
PtRes: IOP
Range: <= PVEULO, NaN

PVEXHIFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
PV Extended High Range Violation FlagIndicates that the PV has exceeded
the extended-high range alarm trip point.
View
Off
HPM
Off (Extended high range not exceeded)
On (Extended high range exceeded)

PVEXHIFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: IOP
Range: 0-Off
1-On

R610
11/99

None
PV Extended High Range Violation FlagIndicates that the PV has
exceeded the extended-high range alarm trip point

HPM Parameter Reference Dictionary


Honeywell Inc.

333

PVEXLOFL

PVEXLOFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
PV Extended Low Range Violation FlagIndicates that the PV has exceeded
the extended-low range alarm trip point.
View
Off
HPM
Off (Extended low range not exceeded)
On (Extended low range exceeded)

PVEXLOFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: IOP
Range: 0-Off
1-On

None
PV Extended Low Range Violation FlagIndicates that the PV has
exceeded the extended-low range alarm trip point.

PVFL(0)(2) (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
PV FlagIndicates the current PV state as three separate Boolean parameters.
PVFL(n) is On when the PV is in state "n" where n is 0, 1, or 2.
View
Off
HPM
Off (PV is not in the respective state)
On (PV is in the respective state)

PVFL (DigIn, Flag)


Type:
Lock:
Default:
PtRes:
Range:

334

Logical
PV FlagRepresents the current PV state as a Boolean value.
Oper
Off
HPM
Off [PV = STATETXT(0)]
On [PV = STATETXT(1)]

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVFL (FBCM)

PVFL (FBCM)
FF Param. Source:
DI: OUT_D.Value
Type:
Logical
PV Flag
Lock:
Oper
Default: Off
PtRes: FF DEVICE
Range: 0-Off [PV = STATETXT(0)]
1-On [PV = STATETXT(1)]

PVFORMAT (FBCM)
FF Param. Source:
AI: OUT_SCALE.DecPt; PID: PV_SCALE.DecPt
Type:
E:VALFORMT PV FormatPV Decimal Format. Defines the decimal format to be
Lock:
View
used to display PV and SP values. It contains up to eight characters
including the minus sign and the decimal point.
Default: 1
PtRes: IOP
Range: 0-D0(0 decimal places)
1-D1(1 decimal place)
2-D2(2 decimal places)
3-D3(3 decimal places)

PVFORMAT (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:VALFORMT
Engr (/PB )
D1
HPM
0-D0 (-XXXXXX.)
1-D1 (-XXXXX.X)
2-D2 (-XXXX.XX)
3-D3 (-XXX.XXX)

PV Decimal Point FormatDefines the decimal format that is to be used


to display the PV and SP values. It contains up to eight characters
including the minus sign and decimal point.

HPM Parameter Reference Dictionary


Honeywell Inc.

335

PVHHFL (FBCM)

PVHHFL (FBCM)
FF Param. Source:
ALARM_SUM.Current
Type:
Logical
PV High High Alarm FlagIndicates whether the PV has exceeded
the alarm trip point established by the PVHHTP parameter.
Lock:
View
Default: Off
PtRes: IOP
Range: Off (High High limit not exceeded)
On (High High limit exceeded)

PVHHFL (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Logical
PV High High Alarm FlagIndicates whether the PV has exceeded the alarm
trip point established by the PVHHTP parameter.
View
Off
HPM
Off (High High limit not exceeded)
On (High High limit exceeded)

PVHHPR (FBCM)
FF Param. Source:
Type:
E:ALPRIOR
Lock:
Engr
Default: Low
PtRes: NIM
Range:

336

HI_HI_PRI
PV High High Alarm PriorityPriority of the PV High High alarm.
This value is mapped from the FF alert priority parameter as follows:
Emergency <- 12- 15; High <- 8 - 11; Low <- 5 - 7; Printer <- 4;
JnlPrint <- 3; Journal <- 2; NoAction <- 1

Emergncy
High
Low
JnlPrint
Printer
Journal
NoAction

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVHHPR (RegCtl, RegPV)

PVHHPR (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR PV High High Alarm PriorityDefines the priority of the PV high high alarm.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: PVHHPR configuration requires PVHHTP ` NaN.

PVHHTP (AnalgIn, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Real
PV High High Alarm Trip PointDefines the PV high high alarm trip point
for this point.
Supr
NaN
HPM
PVHITP to PVEXEUHI, NaN
Helpful Hint: PVHHTP configuration requires PVHITP ` NaN.

PVHHTP (FBCM)
FF Param. Source:
HI_HI_LIM
Type:
Real
PV High High Alarm Trip Point Defines the PV high high alarm
trip point for this point.
Lock:
Supr
Default: +INF
PtRes: IOP
Range: PV_SCALE, +INF

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

337

PVHHTP (RegCtl, RegPV)

PVHHTP (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Real
PV High High Alarm Trip PointDefines the PV high high alarm trip point
Supr
for this point.
NaN
HPM
PVHITP to PVEUHI, NaN
Helpful Hint: PVHHTP configuration requires PVHITP` NaN.

PVHIFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: IOP
Range: 0-Off
1-On

ALARM_SUM.Current
PV High Alarm FlagIndicates that the PV has exceeded the alarm
trip point established by parameter PVHITP.

PVHIFL (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Logical
PV High Alarm FlagIndicates that the PV has exceeded the alarm trip point
View
established by parameter PVHITP.
Off
HPM
Off (No PV High alarm)
On (High PV alarm)

PVHIPR (FBCM)
FF Param. Source:
HI_PRI
Type:
E:ALPRIOR PV High PriorityPriority of the PV High alarm.
This value is mapped from the FF alert priority parameter as follows:
Lock:
Engr
Emergency <- 15; High <- 10 - 14; Low <- 5 - 9; JnlPrint <- 2-4;
Default: NoAction
NoAction <- 1
PtRes: NIM
Range: Emergncy, High, Low, JnlPrint, NoAction

338

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVHIPR (RegCtl, RegPV)

PVHIPR (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR PV High Alarm PriorityDefines the priority of the PV high alarm for this
Engr
point.
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: PVHIPR configuration requires PVHITP ` NaN.

PVHITP
Type:
Lock:
Default:
PtRes:
Range:

Real
PV High Alarm Trip PointDefines the trip point for the PV high alarm for
Supr
this point.
NaN
HPM
PVLOTP to PVHHTP, NaN

PVHITP (FBCM)
FF Param. Source:
HI_LIM
Type:
Real
PV High Alarm Trip PointDefines the trip point for the PV high
alarm for this point.
Lock:
Supr
Default: +INF
PtRes: IOP
Range: PV_SCALE, +INF

PVINIT
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
PV Initialization Request FlagIndicates that an initialization request has
Prog
been made for this point.
Off
HPM
Off (No 1-shot initialization)
On (Initializes the PV filter and the algorithm for a 1-shot single sample time).

HPM Parameter Reference Dictionary


Honeywell Inc.

339

PVLLFL (FBCM)

PVLLFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: IOP
Range: 0-Off
1-On

ALARM_SUM.Current
PV Low Low Alarm Flag Indicates that the PV has exceeded the
alarm trip point established by the PVLLTP parameter.

PVLLFL (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Logical
PV Low Low Alarm FlagIndicates that the PV has exceeded the alarm trip
View
point established by the PVLLTP parameter.
Off
HPM
Off (PV > Low Low alarm trip point)
On (PV < Low Low alarm trip point)

PVLLPR (FBCM)
FF Param. Source:
LO_LO_PRI
Type:
E:ALPRIOR PV Low Low Alarm PriorityPriority of the PV Low Low alarm.
This value is mapped from the FF alert priority parameter as follows:
Lock:
Engr
Emergency <- 15; High <- 10 - 14; Low <- 5 - 9; JnlPrint <- 2-4;
Default: NoAction
NoAction <- 1
PtRes: IOP
Range: Emergncy, High, Low, JnlPrint, NoAction

PVLLPR (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR PV Low Low Alarm PriorityDetermines the priority of the PV low low
Engr
alarm for this data point.
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: PVLLPR configuration requires PVLLTP ` NaN.

340

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVLLTP (AnalgIn, RegPV, PI)

PVLLTP (AnalgIn, RegPV, PI)


Type:
Lock:
Default:
PtRes:
Range:

Real
PV Low Low Alarm Trip PointDefines the trip point for the PV low low
Supr
alarm for this point.
NaN
HPM
PVEXEULO to PVLOTP, NaN
Helpful Hint: PVLLTP configuration requires PVLOTP ` NaN.

PVLLTP (FBCM)
FF Param. Source:
LO_LO_LIM
Type:
Real
PV Low Low Alarm Trip PointDefines the trip point for the PV
low low alarm for this point.
Lock:
Supr
Default: -INF
PtRes: IOP
Range: -INF, PV_SCALE

PVLLTP (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
PV Low Low Alarm Trip PointDefines the trip point for the PV low low
Supr
alarm for this point.
NaN
HPM
PVEULO to PVLOTP, NaN
Helpful Hint: PVLLTP configuration requires PVLOTP ` NaN.

PVLOFL (FBCM)
FF Param. Source:
Type:
Logical
Lock:
View
Default: Off
PtRes: IOP
Range: 0-Off
1-On

ALARM_SUM.Current
PV Low FlagPV Low Limit Flag.

PVLOFL (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
PV Low Alarm FlagIndicates that the PV has exceeded the alarm trip point
View
established by parameter PVLOTP.
Off
HPM
Off (PV > Low alarm trip point)
On (PV < Low alarm trip point)

HPM Parameter Reference Dictionary


Honeywell Inc.

341

PVLOPR (FBCM)

PVLOPR (FBCM)
FF Param. Source:
LO_PRI
Type:
E:ALPRIOR PV Low Alarm PriorityPriority of the PV Low alarm.
This value is mapped from the FF alert priority parameter as follows:
Lock:
Engr
Emergency <- 15; High <- 10 - 14; Low <- 5 - 9; JnlPrint <- 2-4;
Default: NoAction
NoAction <- 1
PtRes: NIM
Range: Emergncy, High, Low, JnlPrint, NoAction

PVLOPR (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR PV Low Alarm PriorityDefines the priority of the PV low alarm for this
Engr
point.
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: PVLOPR configuration requires PVLOTP ` NaN.

PVLOTP (FBCM)
FF Param. Source:
LO_ LIM
Type:
Real
PV Low Alarm Trip PointDefines the trip point for the PV low low
alarm for this point.
Lock:
Supr
Default: -INF
PtRes: IOP
Range: -INF, PV_SCALE

342

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVLOTP (RegCtl, RegPV)

PVLOTP (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Real
PV Low Alarm Trip PointDefines the trip point for the PV low alarm for
this point.
Supr
NaN
HPM
PVLLTP to PVHITP,
NaN

PVNORMAL (DevCtl, DigIn, DigComp)


Type:
Lock:

E:STATETXT
Supr
(Engr to

PV Normal StateDefines the normal state of the PV using the appropriate


STATETXT descriptor.

change
to/from
NONE)
Default: N/A
PtRes: HPM
Range: STATETXT(0) descriptor (Defaulted to Off for PV State 0)
STATETXT(1) descriptor (Defaulted to On for PV State 1)
STATETXT(2) descriptor (Defaulted to State2 for PV State 2; internally set to $NULL for twostate devices; does not apply to DigIn point)
NONE (No off normal checking)
Helpful Hint: PV normal state text descriptor describes the normal (desired) state,
such as Run, Stop, Open, Closed.

PVNORMFL (DevCtl, DigIn, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
PV Normal State FlagIndicates whether the normal state of the PV is active.
Supr
Off
HPM
Off (Point is in a state other than the normal state)
On (Normal state is active)
Helpful Hint: PVNORMFL change requires ALMOPT = Offnorm for Digital Input points,
or that PVNORMAL ` None for Digital Composite or Device Control points.
If set to On, causes text in STATETXT (1) to be used to describe the normal
state of the PV, otherwise text in STATETXT (0) is used.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

343

PVP (FBCM)

PVP (FBCM)
FF Param. Source:
AI: OUT.Value; PID: PV.Value
Type:
Real
PV in PercentDefines the PV as a percentage.
Lock:
View
Default: NaN
PtRes: IOP
Range: 0.0 =< x <= 100.0, NaN

PVP (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

PV in PercentDefines the PV as a percentage.

PVRAW (AnalgIn)
Type:
Lock:
Default:
PtRes:
Range:

Real
Operator
NaN
HPM
N/A

PV Raw ValueIndicates the raw input value of the PV from the Field
Termination Assembly (FTA) before PV characterization is performed. The
units of value for the PV are determined by the field sensor type as described
below.

Helpful Hint: If sensor type is 0.42 V, 1- 5 V, 0 - 5 V, PVRAW is in percent; if sensor type


is T/C, PVRAW is in microvolts; if sensor type is in RTD, PVRAW is in
milliohms; if sensor type is slidewire, PVRAW is in ratio; if sensor type is
0100 mV, PVRAW is in millivolts.

PVRAW (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View
Off
HPM
Off
On

344

Raw State of Field ContactsIndicates the current state of the field contacts.

Open contacts
Closed contacts

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVRAW (FBCM)

PVRAW (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN, Off
PtRes: IOP
Range:

AI: FIELD_VAL.Value; DI: FIELD_VAL_D.Value


PV RawIndicates the field value of the PV (for the AI, it is defined
in % of span as defined in XD_SCALE) as it comes from the transducer
block.
This value appears as a real number in the IOP and on the UCN. For
the DI CMTYPE, it is translated to a logical by the NIM.

Floating Point
0 Off
1 - On

PVRAW (PI)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

PV Raw ValueIndicates the raw input value of the PV in pulses per second.

PVRAW (STI)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

PV Raw ValueIndicates the raw input value of the PV in % of span based on


the transmitter PV after PV characterization (PVCHAR) and DAMPING have
been performed. The span of the PV is determined by using LRV as a 0%-point
and URV as a 100%-point.

PVRAWHI
Type:
Lock:
Default:
PtRes:
Range:

Real
PV Raw High RangeDefines the high end of the normal operating range for
the raw PV value (PVRAW). For a slidewire input, the units are ratio, for a
Eng/PB
0_100_MV input, the units are in millivolts.
NaN
HPM
PVRAWLO to 100 for a 0_100_mv input (microvolts)
PVRAWLO to 1 for a slidewire input (ratio)

PVRAWLO
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
PV Raw Low RangeDefines the low end of the normal operating range for
the raw PV value (PVRAW).
Eng/PB
NaN
HPM
0PVRAWHI (0 to 100 microvolts for a 0_100 mv input, or 0 to 1 ratio for a slidewire input)

HPM Parameter Reference Dictionary


Honeywell Inc.

345

PVROCNFL (RegCtl, RegPV)

PVROCNFL (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Logical
PV Negative Rate-of-Change Alarm FlagIndicates that the PV negative
rate-of-change has exceeded the value established by the PVROCNTP
View
parameter.
Off
HPM
Off (No PV negative rate-of-change alarm)
On (PV negative rate-of-change alarm)

PVROCNPR (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR PV Negative Rate-of-Change Alarm PriorityDefines the priority of the PV


negative rate-of-change alarm for this point.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: PVROCNPR configuration requires PVROCNTP ` NaN.

PVROCNTP (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:

Real
Supr
NaN
HPM

PV Negative Rate-of-Change Trip PointDefines the trip point for the PV


negative rate-of-change alarm for this point. Operation is the same as for
PVROCPTP except for the direction of change.
The maximum rate of change value must be less than the absolute value of:
60
(PVEUHI-PVEULO) * 8 .

Range:

> 0.0,
NaN
Helpful Hint: For RegPV points, RegCtl points, and points in a HLAI or LLAI, the
maximum rate of change is one step away from PVEXEUHI to PVEXEULO
in eight seconds; therefore, the maximum rate of change is
(PVEXEUHI - PVEXEULO) * 7.5 units/minute. For SENSRTYP = RTD, the
maximum is [800 - (-180)] * 7.5, which is 7350.
The value of PVROCNTP saved in the data base is the value entered.

346

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVROCPFL (RegCtl, RegPV)

PVROCPFL (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Logical
PV Positive Rate-of-Change Alarm FlagIndicates that the positive
rate-of-change of the PV has exceeded the value established by the PVROCPTP
View
parameter.
Off
HPM
Off (No PV positive rate-of-change alarm)
On (PV positive rate-of-change alarm)

PVROCPPR (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR PV Positive Rate-of-Change Alarm PriorityDefines the priority of the


positive rate-of-change PV alarm for this point.
Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)
Helpful Hint: PVROCPPR configuration requires PVROCPTP ` NaN.

PVROCPTP (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:

Real
Supr
NaN
HPM

PV Positive Rate-of-Change Trip PointDefines the positive PV rate-ofchange limit in engineering units/minute for this point; for example 25 degrees
per minute. The PV value is checked every four seconds. The rate of change
alarm trips if the PV rate-of-change value is exceeded for two successive scans.
The alarm is reset if the PV rate-of-change falls below the rate of change value
for two successive scans.
The maximum rate of change value must be less than the absolute value of:
60
(PVEUHI-PVEULO) * 8 .

Range:

> 0.0,
NaN
Helpful Hint: For RegPV points, RegCtl points, and points in HLAI or LLAI, the maximum
rate of change is one step away from PVEXEUHI to PVEXEULO in eight
seconds; therefore, the maximum rate of change is:
(PVEXEUHI - PVEXEULO) * 7.5 units/minute.
Example: for SENSRTYP = RTD, the maximum is: [800 - (-180)] *7.5, which = 7350.
The value of PVROCPTP saved in the data base is the value entered.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

347

PVSGCHTP (RegCtl, RegPV)

PVSGCHTP (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
NaN
HPM
> 0.0,
NaN

PV Significant Change Alarm Trip PointDefines the alarm trip point for an
increment of change that occurs between configured PVHITP and PVHHTP or
PVLOTP and PVLLTP alarms. For example, consider a temperature point with
limits of PVHITP = 800 degrees, PVHHTP = 850, and PVSGCHTP = 10. When
the temperature rises to 800 degrees, the PVHITP alarm is annunciated, and
should the temperature continue to increase, the alarm is annunciated again when
the temperature reaches 810 degrees, 820 degrees, and so on. This allows the
alarm to be reannunciated to remind the operator of the existence of an alarm
condition.

PVSOURCE (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:PVSOURCE
PV SourceDefines the source of the PV input to this data point. The PV
goes to bad when PVSOURCE is switched from Man to Sub.
Oper
Auto
HPM
0-Sub (Value is provided by a sequence program)
1-Man (PV is supplied by operator or program)
2-Auto (Field wiring or memory fetch supplies PV)
3-Track (PV tracks OP (DigComp points only))
Helpful Hint: PVSOURCE change by an operator requires PVSRCOPT = All and DITYPE =
Latched if PNTTYPE = DigIn.

PVSRCOPT (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

E:PVSRCOPT
PV Source OptionDefines the PV source options available in this data
point.
Eng/PB
OnlyAuto
HPM
0-OnlyAuto (PV source selection is not available and field wiring or memory fetch supplies PV)
1-All (PV is provided by an operator, by a sequence program, or by field wiring)
Helpful Hint: PVSRCOPT change by an operator requires DITYPE = Latched if
PNTTYPE= DigIn.

348

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVSTATES(0)(4) (DevCtl, DigComp)

PVSTATES(0)(4) (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

String_8
View
N/A
NIM
N/A

PV State DescriptorsThe PV state descriptors contain the text that describes


the five (0-4) possible states of a DigComp or DevCtl PV. The descriptors are
set equal to whatever is configured in BADPVTXT and MOVPVTXT during
HPM Box configuration and in STATETXT(0), STATETXT(1), and
STATETXT(2) during point configuration (if PVTXTOPT = ON).

Helpful Hint: PVSTATES, if accessed by Control Language programs, obey the


following rules:
a. PVSTATES (0) = STATETXT (0)
b. PVSTATES (1) = STATETXT (1)
c. PVSTATES (2) = BADPVTXT
d. PVSTATES (3) = MOVPVTXT
e. PVSTATES (4) = STATETXT (2); does not apply unless
NOSTATES = 3

PVSTS (FBCM)
FF Param. Source:
AI: OUT_STATUS.Quality; PID: PV_STATUS.Quality
Type:
E:$FBSTATS PV StatusStatus of PV parameter.
FFPVSTS will have to be mapped into this parameter.
Lock:
View
Default: Bad
PtRes: IOP
Range: 0-BAD
1-UNCERTAIN
2-NORMAL

PVSTS (RegCtl, RegPV)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:PVVALST
Status Of PV Input ValueDefines the current status of the PV value.
View
Bad
HPM
0-Bad (Value is bad and replaced with NaN. For an STI point, value can be set to Bad based on
transmitter gross status.)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

HPM Parameter Reference Dictionary


Honeywell Inc.

349

PVTEMP

PVTEMP
Type:
Lock:
Default:
PtRes:
Range:

E:TEMPTURE
PV Temperature ScaleDefines the temperature scale to be used in
characterizing the PV input.
PtBld
Degrees C
HPM
0-Degrees C (Celsius)
1-Degrees F (Fahrenheit)
2-Degrees R (Rankin)
3-Degrees K (Kelvin)

Helpful Hint: PVTEMP is to be configured when PVCHAR = TC or RTD.

PVTRACK (Pid)
Type:
Lock:
Default:
PtRes:
Range:

E:TRACKING
PV Tracking OptionDefines whether SP is to be set equal to PV.
Eng/PB
NoTrack
HPM
0-NoTrack (SP is never set equal to PV)
1-Track (Man mode or initialization causes SP to track PV)
Helpful Hint: SP is set equal to PV if PVTRACK = Track and the point is:
a. in manual mode
b. being initialized from a secondary
c. undergoing 1-shot initialization during the first sample time after
becoming active.

PVTV
Type:
Lock:
Default:
PtRes:
Range:

Real
PV Target Value in Engineering UnitsDefines the target value of the PV in
Configurable engineering units.
NaN
HPM
PVEXEULO to PVEXEUHI,

PVTV (FBCM)
FF Param. Source:
None
Type:
Real
PV Target ValuePV target value in engineering units
Lock:
Oper
Default: NaN
PtRes: IOP
Range: PVEXEULO to PVEXEUHI

350

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PVTVP

PVTVP
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
> 0.0%, NaN

PV Target Value in PercentIndicates the target value of the PV in percent.

PVTVP (FBCM)
FF Param. Source:
None
Type:
Real
PV Target Value PercentIndicates the target value of the PV in
percent.
Lock:
View
Default: NaN
PtRes: IOP
Range: 0.0 =< x <= 100.0, NaN

PVTXTOPT (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
PV Text OptionIndicates whether the BADPVTXT and MOVPVTXT
parameters are configured for this point, or if the default from the box data point
PtBld
should be used.
Off
NIM
Off (The parameters are not configured for this point)
On (The parameters are configured for this point)

HPM Parameter Reference Dictionary


Honeywell Inc.

351

-QQ
Type:
Lock:
Default:
PtRes:
Range:

Real
View
1.0
HPM
> 0.0,
NaN

Steam Quality Factor InputIndicates the measured actual steam quality


factor.

QSTS (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

E:PVVALST
Q Input Value StatusIndicates the status of the steam quality-factor input.
View
Normal
HPM
0-Bad (Value is bad and replaced by NaN)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

QUBODIDX (FBCM)
FF Param. Source:
None
Blind record of the object dictionary index of the parameter that must
Type:
Blind
be read periodically using QUB and its parameter identifier. This
Lock:
PtBld
parameter is typically the contained feedback parameter of a remote
Default: 0
cascade input.
PtRes: IOP
Range: Object dictionary index valid range, Parameter ID valid range

QUBRATE (FBCM)
FF Param. Source:
Type:
Real
Lock:
PtBld
Default: 1000
PtRes: IOP
Range: 0 to 65535

352

None
Rate at which the non-view client-server requests are made to the
device by each FBCM in milliseconds.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

R1(1)(24), R2(1)(24) (Logic)

-RR1(1)(24), R2(1)(24) (Logic)


Type:
Lock:
Default:
PtRes:
Range:

E:$PMMLGPM
Real Inputs 1 & 2Defines the sources that provide the input values for
PtBld
the R1 and R2 inputs of certain logic blocks.
L1
HPM
32..47-L1...L12 (Values from Input Connections)
48..51-NN1...NN8 (Local Numerics)
Helpful Hint: R1 configuration requires LOCALGID = EQ, NE, GT, GE, LT, LE, or
CHECKBAD.

RAISDSTN
Type:

Universal
Ent.Prm
Lock:
PtBld
Default: Null
PtRes: HPM
Range: ONPULSE
OFFPULSE

Raise Output Pulse DestinationDefines the destination of the Raise output


pulse. RAISDSTN must point to parameters ONPULSE or OFFPULSE of a
DigOut data point.

RAISETIM
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A,
NaN

Raise Output Pulse TimeIndicates the Raise output pulse time in seconds. It
is clamped to MAXPULSE or CYCLETIM, whichever is lower. If the value of
RAISETIM is smaller than MINPULSE, no pulse is issued.

RAISRATE
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Raise OP Stroke Rate in Percent/Second
Supr
100.0% per sec.
HPM
> 0.0% per second

HPM Parameter Reference Dictionary


Honeywell Inc.

353

RAMPTIME

RAMPTIME
Type:
Lock:
Default:
PtRes:
Range:

Real
Oper
0.0
HPM
> 0.0

Ramp Time in Minutes

Helpful Hint: RAMPTIME change by an operator requires SPOPT = Tv. The minimum value
is clamped to TS, the point sample time in minutes, while the maximum value
is clamped to 32767*TS. To change the RAMPTIME from a logic point requires
Node=Auto and Mode Attribute=Program.

RANGES
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: N/A
Range: N/A

None
This parameter set has been added for compatibility with fieldbus
requirements.

RARWSTS (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:WINDUP
Remote Anti-Reset Windup Status
View
Normal
HPM
0-Normal (Free to move in either direction)
1-Hi (Free to move lower)
2-Lo (Free to move higher)
3-HiLo (Not free to move in any direction)
Helpful Hint: RARWSTS applies only if RCASOPT = Spc, Ddc, or DdcRsp.

RATE1 (AutoMan, MulDiv, RegCtl Summer)


Type:
Lock:
Default:
PtRes:

Real
Supr
0.0
HPM

Range:

> 0.0 EUs per minute, NaN

354

Rate at Which Bias Ramps DownRate at which the bias (B) ramps down
from the initialization value to the last value entered by the operator. If a
positive value is entered, Rate1 determines the ramp down rate of the internal
bias value (BI). If 0 is entered, the ramp down of B is disabled. If NaN is
entered, the internal bias does not decay, but instantaneously changes to 0 and
will cause a bump in the output.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

RATE1 (RatioCtl)

RATE1 (RatioCtl)
Type:
Lock:
Default:
PtRes:

Real
Supr
NaN
HPM

Range:

> 0.0, NaN

Internal Bias Ramps Down RateRate in EUs per minute at which the
internal bias (BI) ramps down from the initialization value to the last value
entered by the operator. If BIAS = NaN, initialization for the primary is
determined through back calculation. If 0 is entered, the ramp down of B is
disabled.

RATE112 (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

Real
Ramp Rate for Ramp Soak Segments 112
Supr
NaN
HPM
Negative values are accepted to allow ramping down.

RATIO (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
RatioDefines the ratio value by which the SP is multiplied.
Oper
1.0
HPM
RTLOLM to RTHILM

RBOPT (Pid)
Type:
Lock:
Default:
PtRes:
Range:

E:RBOPT
Ratio/Bias OptionDefines the type of ratio/bias option to be used for this
algorithm. Refer to the HPM Control Functions and Algorithms manual for a
Eng/PB
detailed description of bias and ratio options.
NoRatBi
HPM
0-NoRatBi (No ratio/bias is used to calculate the SP)
1-FixRatBi (Fixed ratio (R) and fixed bias (B) are used)
2-AutoRat (R is back-calculated during initialization)
3-AutoBi (B is back-calculated during initialization)
Helpful Hint: RBOPT applies to only PID-type RegCtl algorithms.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

355

RCASIN (FBCM)

RCASIN (FBCM)
FF Param. Source:
RCAS_IN
Type:
Blind
Remote Cascade InputFF remote cascade input parameter
Lock:
Prog
(supervisory control). Intended for regulatory-control output
Default: Bad_OOS,
connections only.
Nan
PtRes: IOP
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text
Helpful Hint:

The data of RCASIN cannot be displayed by viewing the parameter directly.


Use FFRCINVL parameter for viewing RCASIN's value part and FFRCINST
parameter for viewing RCASIN's status part.

RCASIND (FBCM)
FF Param. Source:
RCAS_IN_D
Type:
Blind
Remote Cascade Input DiscreteFF discrete remote cascade input
parameter (supervisory control). Intended for digital composite and
Lock:
Prog
Default: Bad_OOS, Off device control output connections only.
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text
Helpful Hint:

The data of RCASIND cannot be displayed by viewing the parameter directly.


Use FFRCIDVL parameter for viewing RCASIND's value part and
FFRCIDST parameter for viewing RCASIND's status part.

RCASOPT (AnalgOut)
Type:
Lock:
Default:
PtRes:
Range:

356

Remote Cascade OptionDefines whether the AM is to provide the output


Eng/PB
value for this data point. This option is available only when the point has been
configured as a Full point.
None
HPM
0-None (No cascade mode of any type is allowed)
2-Ddc (Direct Digital Control; in cascade mode, AM point controls this point's OP)

E:$RCASOPT

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

RCASOPT (AutoMan, IncrSum, ORSel, Switch)

RCASOPT (AutoMan, IncrSum, ORSel, Switch)


Type:
Lock:
Default:
PtRes:
Range:

E:$RCASOPT Remote Cascade OptionDefines the type of remote cascade mode to be


used. Refer to the HPM Control Functions and Algorithms manual for a
Eng/PB
detailed description.
None
HPM
0-None (Only local cascade mode is allowed)
2-Ddc (In cascade mode, AM point provides the output OP for this data point)

RCASOPT (Pid)
Type:
Lock:
Default:
PtRes:
Range:

E:$RCASOPT Remote Cascade OptionDefines the type of remote cascade mode to be


used. Refer to the HPM Control Functions and Algorithms manual for a
Eng/PB
detailed description.
None
HPM
0-None (Local cascade is the only valid cascade)
1-Spc (AM writes to SP within SP limits)
2-Ddc (AM writes to OP. No OP limits)
3-Rsp (AM writes to SP when this point is in Auto and is being initialized by its secondary. SP
limits are applied)
4-DdcRsp (AM does Ddc and Rsp functions)
Helpful Hint: MODE for a point cannot be changed to Cascade by the operator or program if
a. parameter RCASOPT is configured to Ddc, Spc, or DdcRsp
b. the AM strategy has not yet stored to MODE, SP, or OP.
Even if PVTRACK = Track, PV tracking is not performed in auto mode with
INITMAN = On if RCASOPT = Rsp.

RCASOPT (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$RCASOPT Remote Cascade OptionDefines the type of remote cascade mode to be


Eng/PB
used. Refer to the HPM Control Functions and Algorithms manual for a
None
detailed description.
HPM
0-None (Only local cascade mode is allowed)
1-Spc (In cascade mode, AM point provides the SP for this point)
2-DDC (In cascade mode, AM point provides the OP for this point)
3-Rsp (In Auto mode with INITMAN = ON, the AM point provides the SP for this point)
4-DDCRsp (In cascade mode, AM point provides the OP for this point)

HPM Parameter Reference Dictionary


Honeywell Inc.

357

RCASSHED (RegCtl)

RCASSHED (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Remote Cascade ShedIndicates whether the mode has shed from the Cas
View
mode to the preconfigured backup mode.
Off
HPM
Off (No mode shed)
On (Mode has shed to the preconfigured backup mode)
Helpful Hint: RCASSHED applies only if RCASOPT = Spc, Ddc, or DdcRsp.

RDNHWREV
Type:
Lock:
Default:
PtRes:
Range:

String_2
View

HPMM Control Daughter Card Revision

HPM
Hexadecimal Characters 00 to FF

READBACK (FBCM)
FF Param. Source:
Type:
Real
Lock:
View
Default: NaN
PtRes: FF DEVICE
Range: Floating Point

READBACK.Value
Foundation Fieldbus Readback ValueThis indicates the readback
value of the actual continuous valve or other actuator position (in
transducer units).

READBAKD (FBCM)
FF Param. Source:
Type:
Integer
Lock:
View
Default: OFF
PtRes: FF DEVICE
Range: 0-OFF
1 - ON

358

READBACK_D.Value
Foundation Fieldbus Readback Discrete ValueThis indicates the
readback value of the actual discrete valve position or other actuator
position (in transducer units).

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

REDTAG (FBCM)

REDTAG (FBCM)
FF Param. Source:
Type:
E:REDTAG
Lock:
Supr
Default: Off
PtRes: IOP
Range: 0-Off
1-On

None
Red TagRed Tag State. Allows users to set the point in the out of
service condition, indicating that this point or the associated control
loop needs repair or is being repaired. Output is frozen while in red tag
condition.

REDTAG (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:REDTAG Red Tag StateAllows the user to set the point as being "out of service,"
Sup
indicating that this point or the associated control loop needs repair or is being
Off
repaired. Once this point is put in the red tag condition, the output OP is frozen
HPM
at the last value or state.
0-Off (Data point is in service. Point's OP is not frozen)
1-On (Data point is out of service = point's OP is frozen)
Helpful Hint: REDTAG change requires MODE = Man and MODATTR = Oper. Once a
point is red tagged, parameters MODE, MODATTR, and OP (output) cannot
be changed. In addition, for a RegCtl point, ESWENBST cannot be changed.

RELREV (HPM)
Type:
Lock:
Default:
PtRes:
Range:

String_1
View
00 (Hex.)
HPM
N/A

Overall Software Release Revision Code

RELVERS (HPM)
Type:
Lock:
Default:
PtRes:

String_1
View
00 (Hex.)
HPM

Range:

N/A

R610
11/99

Overall Software Release Version Code

HPM Parameter Reference Dictionary


Honeywell Inc.

359

REMDOPT (FBCM)

REMDOPT (FBCM)
FF Param. Source:
None
Type:
E:$REMDOPT Remote Display Option - Indicates what should be displayed for the
remote FF modes, RCas and ROUT.
Lock:
Eng/PB
If the user chose SHOWBCAS, the user would lose the distinction
Default: 0
between RCAS and ROUT. It would be decided internally by the
PtRes: IOP
connection to the FBCM).
If the user chose SHOWCAS, the user would lose distiction between
CAS, RCAS, and ROUT.
Therefore, if the connection information is outside the scope of the TPS
system, the user may not be able to chose the mode that makes the
connection outside of the TPS system.
Range: 0 - SHOWTRUE
1 SHOWBCAS
2 SHOWCAS

REMSOAKT (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

Real
Remaining Soak TimeIndicates the amount of time remaining in the current
soak segment.
Oper
0.0
HPM
0.0 to 120.0 minutes

RESETFL (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Reset Maintenance Statistics FlagUsed to reset maintenance statistics.
Oper
Off
HPM
Off
On (Storing to this parameter resets maintenance statistics)
Helpful Hint: This parameter can be reset by the operator only while it is red tagged. A
program may reset at anytime.

RESETFL (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Reset FlagResets the accumulator to zero when the command flag transitions
from the Off to the On state.
Prog
Off
HPM
Off (No Reset command)
On (Reset command is issued to the accumulator)
Helpful Hint: RESETFL change requires DITYPE = Accum

360

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

RESETFL (Timer)

RESETFL (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

Reset Timer Command FlagResets the total when this flag changes from
Off to On.

RESETFL (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

Reset Totalizer Command FlagResets the total RESETVAL when this flag
changes from Off to On.

RESETVAL (DigIn)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Oper
0
HPM
032767

Accumulator Reset ValueValue that is preset in the accumulator. Value can


then be incremented or decremented depending on the COUNTDWN parameter.

RESETVAL (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Oper
0.0
HPM
N/A

Reset ValueValue used for presetting the value to be totaled.

HPM Parameter Reference Dictionary


Honeywell Inc.

361

RESTART (ProcMod)

RESTART (ProcMod)
Type:
Lock:
Default:
PtRes:

E:RESTART
View
None
HPM

Process Module Restart StateIndicates the type of restart last performed


by the process module. This value will be set to a value other than None
until the first preemption point.

Helpful Hint: RESTART can be used to determine if the startup was caused by failover.
Following failover, RESTART takes on the value Failover. This value remains until
the first preemption point after which it returns to None.
Range:

0-None (Has not been restarted)


1-Failover (Running for the first time after a failover)
3-Warm (Running for the first cycle after a warm start)
4-Cold (Running for the first cycle after a cold start, or a power up to Run)
5-PTACTVN (Running for the first cycle following the transition from Off state to Run
state)

RETCAS (FBCM)
FF Param. Source:
Type:
Logical
Lock:
Eng/PB
Default: Off
PtRes: IOP
Range: 0-Off
1-On

None
Retain Cascade OptionIndicates whether the Cas target should be set or not
automatically every time that the operator enters either Rcas or Rout as the
requested target mode, or when either of these modes are the normal mode.

RFB (PidErfb)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
> 0.0

Reset Feedback Input in PercentIndicates the PV value of another data


point that is receiving its setpoint from this data point.

RG (FlowComp)
Type:
Real
Lock:
Supr
Default: 1.0(molecular
weight)
PtRes: HPM
Range: N/A

362

Reference Specific GravityDefines the reference specific gravity or


reference molecular weight, in the same engineering units as G (measured or
calculated specific gravity or molecular weight).

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

RINITREQ (RegCtl)

RINITREQ (RegCtl)
Type:
Logical
Remote Initialization RequestIndicates whether an initialization request
has been made.
Lock:
View
Default: On for
AnalgOut,
Off for
RegCtl
PtRes: HPM
Range: Off (No request)
On (Request has been made)
Helpful Hint: RINITREQ does not apply if RCASOPT = None.

RINITVAL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Remote Initialization Value
View
NaN
HPM
N/A,
NaN
Helpful Hint: RINITVAL does not apply if RCASOPT = None.

RJRAW(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Reference Junction's Raw Count in Volts

RJTEMP (LLAI)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Reference Junction TemperatureDisplays the current temperatures (C) of


the reference junction sensor. This value is updated only if the thermocouple
input is configured.

RNGCODE3 (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Blind Record
Oper
N/A
HPM

RNGCODE3

HPM Parameter Reference Dictionary


Honeywell Inc.

363

ROUTIN (FBCM)

ROUTIN (FBCM)
FF Param. Source:
ROUT_IN
Type:
Blind
Remote Output InputFF Remote Output Input parameter Intended
for regulatory control output connections.
Lock:
Prog
Default: Bad_OOS,
Nan
PtRes: IOP
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text
Helpful Hint: The data of ROUTIN cannot be displayed by viewing the parameter directly. Use
FFROINVL parameter for viewing ROUTIN's value part and FFROINST parameter for
viewing ROUTIN's status part

RP (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
N/A

Reference PressureRP is the reference pressure input and it is in the same


Engineering Unit as the P (measured or actual gage pressure) input.

Real
Supr
1.0
HPM
0.01 to 100.0

Minimum Pulse Time Ratio

RP
Type:
Lock:
Default:
PtRes:
Range:

RQ (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
N/A

Reference Steam Quality FactorDefines the reference steam quality factor


which is in the same units as the Q (measured actual steam quality) input.

RSPBGP$$ (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:
364

Real
View
N/A
HPM
> 0.0

Ramp/Soak Percent Bar Graph ParameterIf in a ramp sequence, the value


of the next soak percent is displayed. If in a soak sequence, the value of
parameter REMSOAKT as a percent of total soak time is displayed.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

RSSTATE (PECM)

RSSTATE (PECM)
FF Param. Source:
Resource block: RS_STATE
Type:
E:$RSSTATE Resource StateState of the resource block.
Lock:
View
Default: INVALID
PtRes: FF DEVICE
Range: 0-INVALID
1-START
2-INIT
3-ONL_LINK
4-ONLINE
5-STANDBY
6-FAILURE

RSTROPT (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

E:$RSTROPT Restart OptionDefines how the sequence program is to be started


Eng
following an Idle to Run, or power up to Run transition or a warm restart.
Off
HPM
0-Off (Sequence is waiting for the operator command to start)
1-Restart (Sequence is to be restarted from the beginning)
2-Stop (Sequence positions to beginning of the last preemption following a Warm, Cold, or
Power Up Restart and waits for the operator to start

RT (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
1.0
HPM
N/A

Reference TemperatureRT is the reference temperature input and is in the


same Engineering Unit as the T (measured actual temperature) input.

Real
Supr
1.0
HPM
0.01 to 100.0

Deadtime Ratio

RT
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

365

RTHILM (Pid)

RTHILM (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
Ratio High Limit
Supr
100.0
HPM
RTLOLM to 100.0,
NaN
Helpful Hint: Entering NaN forces RTHILM to its extreme value (100.0%).

RTLOLM (Pid)
Type:
Lock:
Default:
PtRes:
Range:

Real
Ratio Low Limit
Supr
0.01
HPM
0.01 to RTHILM,
NaN
Helpful Hint: Entering NaN forces RTLOLM to its extreme value (0.01).

RUNSTATE (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Run StateIndicates that the point is in the RUN sequence execution state.
View
Off
HPM
Off (Process Module point is not in the RUN state)
On (Process Module point is in the RUN state)

RV (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

Remaining TimeIndicates the amount of time remaining (in seconds or


minutes) that the timer is to run.

Helpful Hint: RV represents remaining time computed as SP - PV. If SP = 0, RV


is always 0.

366

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

RX (FlowComp)

RX (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Reference Steam CompressibilityDefines the reference steam
compressibility, and is in the same engineering units as the X (measured actual
Supr
steam compressibility).
1.0
HPM
Anything except NaN

HPM Parameter Reference Dictionary


Honeywell Inc.

367

S0BOXCLR, S1BOXCLR, S2BOXCLR

-SS0BOXCLR, S1BOXCLR, S2BOXCLR


Type:
Lock:
Default:
PtRes:
Range:

E:BOXCOLOR State Box ColorUsed only for US displays; corresponds to the box colors
configured using S0BOXCLR - BOXCLR(0), S1BOXCLR - BOXCLR(1),
View
S2BOXCLR - BOXCLR(2).
N/A
NIM
Red
Green
White
Black
Cyan
Yellow
Blue
Magenta

S1 (PidErfb)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Tracking SwitchDetermines whether the CV value of this data point is
Prog
replaced by the tracking value.
Off
HPM
Off (CV value is not replaced)
On (CV value is replaced by the tracking value)

S1 (STI)
Type:
Lock:
Default:
PtRes:
Range:

String_127
View
Blank
HPM
N/A, Blank

Transmitter StatusIndicates the current status of the smart transmitter


associated with this STI point. Transmitter status consists of
- Transmitter scratch pads 1, 2, 3 & 4
- Detailed transmitter status
- List of parameters whose values are not the same in both the STI IOP database
and the transmitter's database. (Parameters are mismatched.)

S1, S2 (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

368

Logical
View
Off
HPM
Off
On

Mark 1 and Mark 2 FlagsThese flags are used to indicate to other data points
that a specified time has elapsed from the beginning of a specified ramp or soak
segment. Refer to the HPM Control Functions and Algorithms manual for
detailed information.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

S1(1)(24) through S4(1)(24) (Logic)

S1(1)(24) through S4(1)(24) (Logic)


Type:
Lock:
Default:
PtRes:
Range:

E:$PMMLGPM
Status Inputs 1-4Defines the input source for each of the S1-S4 inputs to
the logic block.
PtBld
L1
HPM
FL1...FL12 (Input source is a local flag; they can be either On or Off)
SO1...SO24 (Input source is the status output (SOn) from another logic block.)
L1...L12 (Input source is the configured input connection; they can be either On or Off)

S1S4 (Switch)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Select X1-X4 Request FlagIndicate whether the respective input (X1-X4) has
been selected as the input to this algorithm.
Oper
On
HPM
Off
On (Respective input has been selected)

S1BGNTIM, S2BGNTIM (RampSoak)


Type:
Lock:
Default:
PtRes:
Range:

Real
Mark 1 and Mark 2 Begin TimesTimes at which Mark Function Flag S1 or
S2 is turned on. Refer to the HPM Control Functions and Algorithms manual
Supr
for detailed information.
0.0
HPM
> 0.0 to 120 minutes

S1ENDTIM, S2ENDTIM (RampSoak)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Mark 1 and Mark 2 End TimeTimes at which Mark Function Flags S1 and
S2 are turned Off. Refer to the HPM Control Functions and Algorithms manual
Supr
for detailed information.
0.0
HPM
> 0.0 to 120 minutes

HPM Parameter Reference Dictionary


Honeywell Inc.

369

S1REV(1)(24) through S3REV(1)(24) (Logic)

S1REV(1)(24) through S3REV(1)(24) (Logic)


Type:
Lock:
Default:
PtRes:
Range:

Logical
S1, S2, S3 Inputs ReversedAllows the user to selectively reverse (invert) any
of the inputs to a logic block.
PtBld
Off
HPM
Off (Input is direct)
On (Input is reversed)
Helpful Hint: Reversed (inverted) inputs apply only to LOGALGID = And, Or, Nand, and Nor.

S1SEGID, S2SEGID (RampSoak)


Type:
Lock:
Default:
PtRes:
Range:

E:CURSEGID
Supr
Ramp1
HPM
0-Ramp1
2-Ramp2
:
and
20-Ramp11
22-Ramp12

Mark 1 and Mark 2 Segment IdentifiersRefer to the HPM Control


Functions and Algorithms manual for detailed information.

1-Soak1
3-Soak2

:
21-Soak11
23-Soak12

SAFEOP
Type:
Lock:
Default:
PtRes:
Range:

Real
Safe Operation For Safety ShutdownDefines the safe output value (OP) for
a point when the SHUTDOWN parameter is set to On.
Engr
N/A
HPM
-6.9 to 106.9%,
NaN

SAFOPCMD (PosProp, PIDPosPr)


Type:
E:$SFOPCM
D
Lock:
Default:
PtRes:
Range:

370

Safe OP CommandDefines the Safe OP state for position proportional and


PID position proportional.

Engr
Idle
HPM
0-IDLE (Output does not change)
1-RAISE (Output is raised)
2-LOWER (Output is lowered)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SCANPER (HPM Box)

SCANPER (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
PtBld
1.0
HPM
.25 seconds
.5 seconds
1.0 seconds

SI Data Scan PeriodDefines the period that the HPMM Control Processor
scans serial interface data that is mapped to the Array point.

SCANPRI (Array)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$SCANPRI SI Data FTA Scan PriorityIndicates which scan priority the serial interface
FTA is using when reading data from the serial link.
PtBld
Low
HPM
Low (Scan at low priority)
High (Scan at high priority)

HPM Parameter Reference Dictionary


Honeywell Inc.

371

SCANRATE (HPM Box)

SCANRATE (HPM Box)


Type:
E:$PMMSNR
T
Lock:
PtBld
Default: Reg1Log1
PtRes: HPM
Range:
0-Null
1-Reg1Log1
2-Reg1Log2
3-Reg1Log4
5-Reg2Log2
6-Reg2Log4
8-Reg4Log4

Scan RateDefines the number of times that all slots of a particular type are
scanned and processed. Refer to the HPM Control Functions and Algorithms
manual for information on how to determine the processing capacity of the
HPM. During the load of the HPM Box Data point, the point mix (number of
points and box variables) and the scan rate are written to the HPMM by the
store of the SCANRATE parameter.

RegCtl & RegPV


Scan Freq
---1 second
1 second
1 second
1/2 second
1/2 second
1/4 second

Logic, DigComp & DevCtl


Scan Freq
---1 second
1/2 second
1/4 second
1/2 second
1/4 second
1/4 second

ProcMod
Scan Freq
---1 second
1 second
1 second
1 second
1 second
1 second

CAUTION
If a new point mix or a new SCANRATE is loaded from the DEB, the following items should be noted:
a. Before making changes to the point mix or SCANRATE, any configured points being removed due
to a reduction in the point mix should first be deleted from the system.
b. Any other currently configured points are preserved in the new point mix (the point database is not
defaulted).
c. If the SCANRATE or any part of the point mix is rejected by the HPMM then the HPMM database
remains unchanged; the SCANRATE and the point mix also remain unchanged.
d. If the SCANRATE and the point mix are equivalent to the previous values, then the HPMM
database remains unchanged.

SCHDATA1 (1-2), SCHDATA2 (1-2) (SECM)


FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range:

372

Network Management Information Block


Schedule 1 Data and Schedule 2 DataIOP link schedule 1 and
schedule 2 data, respectively.
IOP link schedule 1 data must be written before the first element of
SCHDSIZE.
IOP link schedule 2 data must be written before the second element of
SCHDSIZE.

N/A

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SCHDSIZE(1-2) (SECM)

SCHDSIZE(1-2) (SECM)
FF Param. Source:
Network Management Information Block related
Type:
Real
IOP Link Schedule SizeOne size per schedule. The first element is
for schedule 1 and the second element is for schedule 2.
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 0 32767 (Must be greater than a schedule with at least one sub-schedule with one sequence, that
is: 28 + 16 +11 = 55 octets.)

SCHDVER(1-2) (SECM)
FF Param. Source:
Type:
Real
Lock:
View
Default: 0
PtRes: IOP
Range: 0 - 65535

Network Management Information Block


Schedule VersionVersions of the schedules that have been loaded.

SCHSTS
Type:
Lock:
Default:
PtRes:
Range:

Logical
Schedule StatusIndicates the status of the schedule configuration option
processing (for example, before/after relationship).
View
OK
HPM
OK (the point is correctly assigned to the desired scan cycle or before/after another point with the
same status)
Incomplete (the point did not complete loading to the point where the proper scan cycle or the
before/after point could be determined. )
Error (the point could not be placed on the desired scan cycle or before/after the desired point)
Alarm (the schedule configuration of the point was violated after the configuration of the point
was complete and its status was Ok.)
Helpful Hint: The point cannot be made active if SCHSTS = Incomplete or Error.

SEALOPT (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$SEALOPT Seal-in Circuit OptionConfigures the seal-in circuit option.


Eng/PB
None
HPM
0-None (Sealin is not configured)
1-Sealin (Sealin is configured)

HPM Parameter Reference Dictionary


Honeywell Inc.

373

SECOND (HPM Box)

SECOND (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
0 to 59

Current Second

SECSYNC
Type:
Lock:
Default:
PtRes:
Range:

E:$SECSYNC Secondary Synchronization Status


View
HPM
Synched (Modules are synchronized)
NoSynch (Modules are out of synchronization)

SECVAR (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Secondary VariableThe analog feedback, normally the motor current or flow.
View
0.0
HPM
Real Numbers including NaN

SECVAR (STI)
Type:
Lock:
Default:
PtRes:

Real
View
NaN
HPM

Range:

N/A, NaN

Secondary VariableDisplays the value of the secondary variable of the smart


transmitter as follows:
Pressure transmittertemperature of the transmitter
Temperature transmittercold junction temperature
Flow transmittertotalized value.

SEGTOT (GenLin)
Type:
Lock:
Default:
PtRes:
Range:

374

Integer
Supr
1
HPM
1 to 12

Total Number of SegmentsDefines the total number of segments in the


curve.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SEGTYPE (RampSoak)

SEGTYPE (RampSoak)
Type:
Lock:
Default:
PtRes:
Range:

E:SEGTYPE
Segment TypeIndicates the current segment being executed by the RegCtl
point.
View
N/A
HPM
0-Ramp (Ramp segment)
1-Soak (Soak segment)

SEL1 (FBCM)
FF Param. Source:
SEL_1
Type:
Real
Selector 1The first input value to the control selector. Intended for
regulatory control output connections only
Lock:
Prog
Default: Bad, NaN
PtRes: IOP
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text
Helpful Hint:

The data of SEL1 cannot be displayed by viewing the parameter directly. Use
FFSEL1VL parameter for viewing the value part of SEL1 and use the
FFSEL1ST parameter for viewing the status part of SEL1.

SEL2 (FBCM)
FF Param. Source:
SEL_2
Type:
Real
Selector 2 The second input value to the control selector. Intended
for RegCtl output connections only.
Lock:
Prog
Default: Bad, NaN
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text
Helpful Hint:

R610
11/99

The data of SEL2 cannot be displayed by viewing the parameter directly. Use
FFSEL2VL parameter for viewing the value part of SEL2 and use the
FFSEL2ST parameter for viewing the status part of SEL2.

HPM Parameter Reference Dictionary


Honeywell Inc.

375

SEL3 (FBCM)

SEL3 (FBCM)
FF Param. Source:
SEL_3
Type:
Real
Selector 3The third input value to the control selector. Intended for
RegCtl output connections only.
Lock:
Prog
Default: Bad, NaN
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text
Helpful Hint:

The data of SEL3 cannot be displayed by viewing the parameter directly. Use
FFSEL3VL parameter for viewing the value part of SEL3 and use the
FFSEL3ST parameter for viewing the status part of SEL3.

SELINP (HiLoAvg, MidOf3)


Type:
Lock:
Default:
PtRes:
Range:

E:PINP
Selected InputIndicates the selected input for the algorithm.
View
SelectP1
HPM
1-SelectP1 (HiLoAvg and MidOf3 algorithms)
2-SelectP2 (HiLoAvg and MidOf3 algorithms)
3-SelectP3 (HiLoAvg and MidOf3 algorithms)
4-SelectP4 (Only HiLoAvg algorithm)
5-SelectP5 (Only HiLoAvg algorithm)
6-SelectP6 (Only HiLoAvg algorithm)

SELXINP (ORSel, Switch)


Type:
Lock:

E:XINP
View
(for ORSel)
Oper
(for Switch)
Default: SelectX1
PtRes: HPM
Range: 1-SelectX1
2-SelectX2
3-SelectX3
4-SelectX4

376

Selected X InputFor the ORSel algorithm, this parameter indicates the


inputs to the algorithm that have not been bypassed by the BYPASS1BYPASS4 parameters. For the Switch algorithm, this parameter allows the
operator to specify the input (X1-X4) to the algorithm. Refer to the HPM
Control Functions and Algorithms manual for a detailed description.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SENSRTYP (HLAI & LLAI)

SENSRTYP (HLAI & LLAI)


Type:
Lock:
Default:
PtRes:
Range:

E:$SENSRTY
Sensor TypeDefines the type of field sensor connected to the Field
Termination Assembly (FTA). 0_100_mV, Thermocouple, and RTD sensor
PtBld
types do not apply for HLAI. P4_2_V and slidewire sensor types do not apply
1_5_V
for LLAI. Refer to PVCHAR for more information.
HPM
0-1_5_V (1 to 5 volts)
1-0_5_V (0 to 5 volts)
2-0_100_mV (0 to 100 millivolts)
3-Thermcpl (Thermocouple)
4-RTD (Resistance Temperature Device)
5-P4_2_V (0.4 to 2 volts)
6-Slidwire (Slidewire Resistance Device)

SENSRTYP (LLMUX, RHMUX)


Type:
Lock:
Default:
PtRes:
Range:

E:$SENSRTY
Sensor TypeDefines the type of field sensor connected to the Field
Termination Assembly (FTA). Refer to PVCHAR for more information.
PtBld
0 - 100 mV
HPM
2-0_100_mV (0 to 100 millivolts)
3-Thermcpl (Thermocouple)
4-RTD (Resistance Temperature Device) NOTE: RTD is not supported by RHMUX.

SENSRTYP (STI)
Type:
Lock:
Default:
PtRes:
Range:

E:$SENSRTY
Sensor TypeDefines the Smart Transmitter type. Refer to PVCHAR for
more information. Note that SENSRTYP must match the FTA. The point
PtBld
status is set to SOFTFAIL if a mismatch occurs.
Spt_Dp
HPM
8-SPT_DP (ST3000differential pressure)
9-SPT_GP (ST3000gauge pressure)
10-SPT_AP (ST3000absolute pressure)
11-STT (STT3000temperature)
12-SFM (MagneW 3000magnetic flow and most Multivariable transmitters)
Helpful Hint: For multivariable transmitters, refer to the transmitter manual for the default value of the
specific device.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

377

SEQERR (ProcMod)

SEQERR (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Sequence ErrorIndicates that a sequence error or failure was detected. A
View
code is displayed to indicate the nature of the error or failure. When an error is
0
detected, the sequence execution state is changed to ERROR; when a failure is
HPM
detected, the execution state is changed to FAIL.
0 (No error)
1-100 (Not used)
Error Codes
101 (Not used)
102 (Array index error)
103 (Illegal IMD code)
104 (Illegal variable/operator code)
105 (Interpreter stack overflow)
106 (GOTO destination error)
107 (Key level error)
108 (Configuration mismatch error)
109 (I/O Link prefetch overflow)
110 (Subroutine nesting level error)
111 (Illegal value error)
112 (Fail statement)
113 (IOL-Prefetch buffer full)
114 (IOL-Poststore buffer full)
115 (UCN-Prefetch buffer full)
116 ((UCN-Postore buffer full)
117-164 (Not used)
Failure Codes
165 (Sequence has been halted by the operator)
166 (Sequence jumped to an abnormal condition handler which was not enabled)
167 (Not used)
168 (Timeout condition occurred on WAIT statement)
169 (An attempt was made to start a sequence that has not been loaded)
170 (Communication error in READ/WRITE statement)
171 (Communication error detected during I/O Link access. This error is also generated for all
post-store problems)
172 (Range Error)
173 (An attempt was made to write to a point that was not in the proper mode)
174 (Interlock error)
175-255 (Not used)

378

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SEQEXEC (ProcMod)

SEQEXEC (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

E:SEQEXEC
Sequence Execution StateIndicates the current execution state of the
View
sequence program that is executing in the process module. Refer to the HPM
NL
Control Functions and Algorithms manual for a detailed description of the
HPM
execution states.
0-NL (Not Loaded)
1-DLL (Down-line loading is in progress)
2-Loaded (Sequence has been loaded into the process module)
3-End (Sequence has stopped because it has run to completion)
4-Pause (Sequence has stopped because of a PAUSE statement, or after each step is executed while in the
SnglStep sequence execution mode.)
5-Fail (Sequence has stopped because a sequence failure was detected)
6-Error (Sequence has stopped because a sequence error was detected)
7-Run (Sequence is running in the process module)

SEQMODE (ProcMod)
Type:
Lock:

E:SEQMODE
Sequence Execution ModeDefines the manner in which the sequence is
Determined by
executed.
CNTLLOCK
parameter
Default: Auto
PtRes: HPM
Range: 0-Auto (Normal mode of sequence operation. Sequence runs from beginning to end without operator
intervention.)
1-SemiAuto (Sequence stops at all PAUSE statements in the sequence. Operator action is required to
restart the sequence.)
2-SnglStep (Sequence is executed one step at a time, and operator action is required to resume execution.
This mode is normally used for debugging.)

SEQNAME (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

String_8
View
Blank
HPM
N/A

Sequence NameDefines the name of the CL sequence that currently resides in


the process module.

SEQOBJSZ (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
View
0
HPM
>0

Sequence Program SizeIndicates the number of memory blocks used by the


sequence currently loaded in this process module.

HPM Parameter Reference Dictionary


Honeywell Inc.

379

SEQPR (ProcMod)

SEQPR (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR Sequence PriorityDefines the alarm priority for Process Module points. Note
Engr
that even when the Sequence priority is Journal, the alarm indicators still appear
Low
on the Group and Detail displays.
NIM
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

SEQPRGSZ (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
N/A
HPM
N/A

Sequence Program SizeGives total HPM memory available for sequence


program, in blocks.

SEQPROC (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

E:$SEQPROC
Sequence Processing RateSpecifies the number of processing units per
Process Module data points that can be processed each quarter second cycle.
PtBld
1_PU
HPM
1_PU One PU per Process Module point allocated per scan (200 points can be processed per scan)
2_PU Two PUs per Process Module point allocated per scan (100 points can be processed per scan)

SEQSLTSZ (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
0
HPM
>0

Sequence Slot SizeDefines the size of the program memory allocated for this
process module in terms of blocks. Each block is 32 words long. The actual size
is limited by the available memory.

SERIALNO (STI)
Type:
Lock:
Default:
PtRes:
Range:

380

String_8
View
Blank
HPM
N/A

Serial Number/PROM Number of the Smart Transmitter

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SGALGID(1)(2) (DevCtl)

SGALGID(1)(2) (DevCtl)
Type:

E:$GTALGID Secondary Gate IDDefines the algorithm IDs for secondary gates.
in an Array
(1..2)
Lock:
PtBld
Default: None
PtRes: HPM
Range: NULL (No algorithm)
AND (And Gate algorithm)
OR (Or Gate algorithm)
NAND (Nand Gate algorithm)
NOR (Nor Gate algorithm)
XOR (Exclusive Or Gate algorithm)
PAND (Pulse Nand Gate algorithm)
POR (Pulse or Gate algorithm)
PNAND (Pulse Nand Gate algorithm)
PNOR (Pulse Nor Gate algorithm)
PXOR (Pulse Exclusive or Gate algorithm)

SGDSTN(1)(2) (DevCtl)
Type:

E:$GATDSTN Secondary Gate DestinationDefines the output destination for the secondary
gates.
in an Array
(1..2)
Lock:
PtBld
Default: None
PtRes: HPM
Range: None (No destination)
SI0 (Output goes to Safety Interlock)
I0, I1, I2 (Output goes to Interlocks)
P0, P1, P2 (Output goes to Permissives)
SOCMD0, SOCMD1, SOCMD2 (Output is commanded to go to SOCMD0, 1 or 2)
OPCMD (Output is commanded to go to OPCMD parameter)

SGPLSWTH(1)(2) (DevCtl)
Type:

Integer
in an Array
(1..2)
Lock:
Supr
Default: 0
PtRes: HPM
Range: 0 to 8000

R610
11/99

Pulse Width for Secondary GateIndicates the pulse width for gates whose
algorithms begin with P.

HPM Parameter Reference Dictionary


Honeywell Inc.

381

SGSO(1)(2) (DevCtl)

SGSO(1)(2) (DevCtl)
Type:

Logical
in an Array
(1..2)
Lock:
View
Default: Off
PtRes: HPM
Range: Off
On

Status Output for Secondary Gates

SHEDMODE (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:MODE
ShedmodeDefines the mode to which this point sheds when it sheds from the
Cas mode.
Engr
Man
HPM
1-Man (Manual)
3-Auto (Automatic; applies to only Pid, PosProp, and RatioCtl algorithms)
4-Bcas (Backup Cascade)
Helpful Hint: 1. SHEDMODE configuration requires RCASOPT = Spc or Ddc for Pid
algorithm.
2. SHEDMODE configuration requires RCASOPT = Ddc for the following
algorithms:
AutoMan
IncrSum
ORSel
Switch
3. SHEDMODE configuration requires RCASOPT = Spc for the following
algorithms:
PosProp
RatioCtl

SHEDTIME (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Eng/PB
0
HPM

Remote Cascade Shed TimeDefines the amount of time between successive


updates of the SP or OP value from the AM. If the update is not received within
the specified time, the AM or the NIM is assumed to have failed, and the backup
control strategy is substituted by means of changing the mode to a preconfigured
backup mode.
0 to 1000 seconds
Helpful Hint: SHEDTIME configuration requires RCASOPT = Spc, Ddc, or DdcRsp, which indicates
that the SP or OP value is provided by the AM. To disable mode shed, use the default value of 0 for this
parameter.

382

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SHUTDOWN (RegCtl)

SHUTDOWN (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Prog
Off
HPM
Off
On

Shutdown Command FlagThis optional parameter allows the user to


implement safety interlocks that can effectively shutdown a single control loop.
When the SHUTDOWN flag is set to On by a user-written program or logic
block, the mode and mode attribute are changed to Man and Oper, respectively,
and the OP output is set equal to a predefined safe output value (SAFEOP). As
long as the SHUTDOWN flag is On, the MODE, MODATTR, ESWENBST,
and OP parameter values cannot be changed. When the SHUTDOWN flag is set
to Off, the control loop must be manually restarted.

Helpful Hint: Before a program sets this flag to the On state, it should write into parameter
SAFEOP a safe shutdown value of 0%, 100%, or NaN (which causes the
last good OP value to be used).
A Logic Point or CL program must be used to reset the Shutdown Flag.

SI0 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Safety Override Interlock Flag
Engr
Off
HPM
Off (Override is not active)
On (Override is active)
Helpful Hint: This parameter can be changed by the engineer only when the point is
inactive or when the HPM is idle.

SI0ALOPT (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:$OVRALOP
SI0 Safety Override AlarmIndicates the required action to be performed
when a safety interlock occurs.
Eng/PB
None
HPM
None (No override alarming)
Auto_Rtn (Return to normal when override is cleared)
Cnfm_Rqd (Confirm to clear, after interlock is cleared)

HPM Parameter Reference Dictionary


Honeywell Inc.

383

SI0ALPR (DevCtl, DigComp)

SI0ALPR (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

E:ALPIROR
Override SI0 Alarm PriorityIndicates the alarm priority for the safety
override.
Engr
NoAction
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

SIALGID(1)(12) (DevCtl)
Type:

E:$I2ALGID Secondary Input Gate Algorithm IDIndicates the algorithm IDs for
secondary input gates.
in an Array
(1..12)
Lock:
PtBld
Default: Null
PtRes: HPM
Range: NULL (No algorithm)
DLY (Input is Delayed algorithm)
ONDLY (On Delay algorithm, transition to ON is delayed)
OFFDLY (Off Delay algorithm, transition to OFF is delayed)
PULSE (Input is Pulsed algorithm)
MAXPULSE (Maximum Pulse Width algorithm)
MINPULSE (Minimum Pulse Width algorithm)

SIDLYTIM(1)(12) (DevCtl)
Type:

Integer
Secondary Input Gate Delay/Pulse WidthIndicates the delay or pulse width
for secondary input gates.
in an Array
(1..12)
Lock:
Supr
Default: 0
PtRes: HPM
Range: 0 to 8000 seconds

384

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SIDSTN(1)(12) (DevCtl)

SIDSTN(1)(12) (DevCtl)
Type:

Destination for Secondary Input GatesDefines the output destination of the


in an Array
secondary gate.
(1..12)
Lock:
PtBld
Default: None
PtRes: HPM
Range: None (No destination)
SI0 (Output goes to Safety Interlock)
I0, I1, I2 (Output goes to Interlocks)
P0, P1, P2 (Output goes to Permissives)
SOCMD0, SOCMD1, SOCMD2 (Output is commanded to go to SOCMD0, 1 or 2)
OPCMD (Output is commanded to go to OPCMD)
SG1, SG2 (Output goes to Secondary gates 1 or 2)
PG1, PG2, PG3, PG4 (Output goes to Primary gates 1, 2, 3 or 4)
E:$GATDSTN

SIMDST (FBCM)
FF Parameter Source:
SIMULATE.Simulate Status
Type:
E:$FBSTATS
Simulate Descrete StatusStatus of the function blocks discrete
Lock:
Eng
simulation variable.
Default: 0
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

SIMDVL (FBCM)
FF Parameter Source:
Type:
Integer
Lock:
Eng
Default: 0
PtRes: IOP
Range: 0-OFF
1-ON

R610
11/99

SIMULATE.Simulate Value
Simulate Discrete VariableValue of the function blocks discrete
simulation variable.

HPM Parameter Reference Dictionary


Honeywell Inc.

385

SIMDXST (FBCM)

SIMDXST (FBCM)
FF Parameter Source:
SIMULATE.Transducer Status
E:$FBSTATS
Type:
Simulate Discrete Transducer StatusStatus of the transducer
blocks discrete simulation variable.
Lock:
Eng
Default: 0
PtRes: LCN
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

SIMDXVL (FBCM)
FF Parameter Source:
Type:
Real
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: 0-Off
1-On

SIMULATE.Transducer Value
Simulate Discrete Transducer ValueValue of the transducer
blocks discrete simulation variable.

SIMENBL (FBCM)
FF Parameter Source:
SIMULATE.Simulate Enable/Disable
Type:
E:$SIMENBL Simulate Enable/DisableSimulation enable/disable flag of the
simulation variable.
Lock:
Eng
Default: Disabled
PtRes: FF DEVICE
Range: 0-Not initialized
1-Disabled
2-Active

SIMSTAT (FBCM)
FF Parameter Source:
SIMULATE.Simulate Status
E:$FBSTATS
Type:
Simulate StatusStatus of the function blocks analog simulation
variable.
Lock:
Eng
Default: 0
PtRes: FF DEVICE
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

386

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SIMVAL (FBCM)

SIMVAL (FBCM)
FF Parameter Source:
SIMULATE.Simulate Value
Simulate StatusValue of the function blocks analog simulation
Type:
Real
variable.
Lock:
Eng
Default: 0
PtRes: IOP
Range: Floating Point

SIMXSTAT (FBCM)
FF Parameter Source:
SIMULATE.Transducer Status
Type:
E:$FBSTATS Simulate Transducer StatusStatus of the transducer blocks analog
simulation variable.
Lock:
View
Default: 0
PtRes: IOP
Range: 0-False/Off/Close or State 0
1-True/On/Open or State 1
2-255-Profile groups will define states 2-255 and corresponding engineering text

SIMXVAL (FBCM)
FF Parameter Source:
SIMULATE.Transducer Value
Simulate Transducer ValueValue of the transducer blocks analog
Type:
Real
simulation variable.
Lock:
View
Default: 0
PtRes: FF DEVICE
Range: Floating Point

SI0CONF (DigComp,DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Oper
Off
HPM
N/A

Safety Override Interlock Alarm Confirmation FlagIndicates that the


safety override interlock alarm needs to be confirmed.

SISO(1)(12) (DevCtl)
Type:

Logical
in an Array
(1..12)
Lock:
View
Default: Off
PtRes: HPM
Range: Off
On

R610
11/99

Status Output for Secondary Input GatesIndicates the output value of the
secondary input gate.

HPM Parameter Reference Dictionary


Honeywell Inc.

387

SLOTNUM

SLOTNUM
Type:
Lock:
Default:
PtRes:

Integer
PtBld
N/A
NIM

Slot NumberDefines the slot number where this point resides. For IOP point
types (AnalgIn, AnalgOut, DigIn, DigOut), it defines the hardware subslot on the
module (IOP card) in which the point resides; refer to description of MODNUM
parameter. For control points (DigComp, DevCtl, Array, Logic, RegPV, RegCtl,
Flag, Numeric, Timer and ProcMod) it defines the software slot in the PMM.
The processing capacity of the HPM depends on the number and mix of
configured control points. Refer to the HPM Control Functions and Algorithms
manual for a detailed description of how to determine the processing capacity of
the HPM, based on the number of control points being used.
For multivariable Smartline transmitters, note that although the transmitter is
connected to only one slot, you must allocate adjacent slots for the other PVs.

Range:

AnalgIn (1-16 for HLAI and STI; 132 for LLMUX and RHMUX)
AnalgIn (1-8 for LLAI)
Array (1-500, but ` the value of NARRSLOT)
DevCtl (1-400, but ` the value of NDEVSLOT)
DigComp (1-999, but ` the value of NDCSLOT)
DigIn (1-32)
DigOut (1-16 or 1-32)
Flag (HPM Box Flag 1-2047)
LLMUX (1-32)
Logic (1-400, but ` the value of NLOGSLOT)
Numeric (HPM Box Numeric 1-2047)
ProcMod (1-250, but ` the value of NPMSLOT)
PI (1-8)
RegCtl (1-250, but ` the value of NCTLSLOT)
RegPV (1-125, ` the value of NPVSLOT)
Timer (HPM box Timer 1-64)
AnalgOut (1-8 or 1-16)
Helpful Hint: SLOTNUM configuration for Digcomp, DevCtl, Array, Flag, Numeric, Timer,
ProcMod,Logic, RegCtl, and RegPV points require CTLOPT = On.

388

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SLOTNUM (FBCM, PECM, SECM)

SLOTNUM (FBCM, PECM, SECM)


FF Param. Source:
None
Type:
Integer
Slot NumberControl Module slot number.
Lock:
PtBld
Default: Blank
PtRes: NIM
Range: 1-119 for FBCM & PECM
120-123 for SECM

SLOT0SF(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

String_96
View

Slot 0 Soft FailuresReturns blind record of box soft failures present at a


module address.

HPM
Hexadecimal Characters 00 to FF

SLOTSFBT (FBCM, PECM, SECM)


FF Param. Source:
Type:
Integer
Lock:
View
Default: All Off
PtRes: IOP
Range: N/A

None
Slot Soft Failure Bits

SLWSRCID (AnalgIn)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Eng/PB
1
HPM
116

Slidewire Voltage Source IdentifierDefines the slot number of the voltage


source for the slidewire.

Helpful Hint: SLWSRCID configuration requires SENSRTYP = Slidewire.

SMCONFIG (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: N/A

R610
11/99

System Management Information Block


System Management Configuration Parameters

HPM Parameter Reference Dictionary


Honeywell Inc.

389

SMODIDX(1-5) (PECM)

SMODIDX(1-5) (PECM)
FF Param. Source:
Type:
Real
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 0 - 65535

System Management Information Block


System Management Information Block Directory Objects Indices

SMODOBJS(1-5) (PECM)
FF Param. Source:
Type:
Real
Lock:
PtBld
Default: 0
PtRes: IOP
Range: 0 - 65535

System Management Information Block


Number of Objects in each System Management Information Block
Directory Entry

SNAME(1)(2) (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

String_8
View
Spaces
HPM
N/A

Subroutine NameIndicates the name of the subroutine currently used by the


process module. A value of means that no subroutine is executing.
SNAME(1) and SNAME(2) display the name of the first and second level
subroutines called from the main sequence.

SO (DigOut)
Type:
Lock:
Default:
PtRes:
Range:

Status OutputThe output from a digital output point.


Logical
Oper
Off
HPM
Off (Field contact is to be de-energized.)
On (Field contact is to be energized.)
Helpful Hint: Only the HPMM Cont_Ctl access level can write to this parameter.

SO (FBCM)
FF Param. Source:
Type:
Logical
Lock:
Oper
Default: Off
PtRes: IOP
Range: 0-Off
1-On

390

DO: OUT_D.Value
Status OutputThe output from a discrete output point

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SO (Timer)

SO (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Status Output of TimerIndicates whether the PV (elapsed time) has reached
View
the SP (preset time).
Off
HPM
On (PV has reached the SP)
Off (PV has not reached the SP)

SO(1)(24) (Logic)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Logic Block Status OutputIndicates the output state of the logic block.
View
Off
HPM
Off (Output is false)
On (Output is true)

SO(0)(2) (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
View
Off
HPM
Off
On

Status output arrayIndicates the current output state of a device control


point or a digital composite slot.
s = (0) for state 0
s = (1) for state 1
s = (2) for state 2

SOAKT112
Type:
Lock:
Default:
PtRes:
Range:

Real
Soak Time for Soak Segments 112Define the soak time in minutes for each
Supr
soak segment.
0.0
HPM
0.0 to 120.0 minutes

SOAKV112
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Supr
NaN
HPM
N/A

Soak Value for R/S Segments 112 Defines the soak values in engineering
units for each soak segment.

HPM Parameter Reference Dictionary


Honeywell Inc.

391

SOCMD(0)(2) (DevCtl, DigComp)

SOCMD(0)(2) (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Output Status CommandWhen commanding an OFF to ON write, the OP is
Prog
commanded to the state corresponding to the array element written on an off-toOFF
on transition.
HPM
On (The OP is commanded to the state corresponding to i. 0=State 0, 1=State 1, 2=State 2 if
SOCMD (i) was previously OFF)
Off (No action)

SP (FBCM)
FF Param. Source:
AO, PID: SP.Value
Type:
Real
Setpoint of the PV in Engineering Units
Lock:
Oper
Default: NaN
PtRes: IOP
Range: PV_SCALE +/- 10%

SP (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Setpoint of the PV in Engineering Units
Oper
0.0
HPM
SPLOLM to SPHILM
Helpful Hint: SP usually does not require a control input connection. If a cascade
connection to SP is required, it is typically configured by specifying a control
output connection on the primary point.

SP (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Oper
0
HPM
0 to 32000

Preset TimeDefines the amount of time in seconds or minutes that the timer
is to run.

SPEUHI (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

392

Real
View
N/A
HPM
> SPEULO

Setpoint Engineering Unit High Range

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SPEULO (RegCtl)

SPEULO (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
< SPEUHI

Setpoint Engineering Unit Low Range

SPFORMAT (FBCM)
FF Param. Source:
AO, PID: PV_SCALE.DecPt
Type: E:VALFORMT Setpoint Decimal Point FormatIndicates the format of the SP
Lock:
View
value.
Default: 1
PtRes: FF DEVICE
Range: 0-D0 (XXXX.)
1-D1(XXX.X)
2-D2 (XX.XX)
3-D3 (X.XXX)

SPFORMAT (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:VALFORMT
View
N/A
HPM
0-D0 (XXXX.)
1-D1 (XXX.X)
2-D2 (XX.XX)
3-D3 (X.XXX)

Setpoint Decimal Point FormatIndicates the format of the SP value.


SPFORMAT tracks with the selected PVFORMAT.

SPHIFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Logical
Setpoint High Limit Violation FlagIndicates the SP has exceeded the upper
View
limit established by SPHILM.
Off
HPM
Off (High limit not exceeded)
On (High limit exceeded)

HPM Parameter Reference Dictionary


Honeywell Inc.

393

SPHILM (RegCtl)

SPHILM (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Setpoint High LimitDefines the upper limit for the SP.
Supr
NaN
HPM
SPLOLM to SPEUHI,
NaN
Helpful Hint: 1. Entering NaN disables limit checking by forcing SPHILM to its extreme
value (SPEUHI).
2. SPHILM does not apply for the RampSoak algorithm.

SPLOCK (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

E:ACCLVL
Setpoint LockStores to the process module points own flags, numeric,
strings, and time parameters, and are checked against the access lock specified
Engr
by SPLOCK.
Operator
HPM
0-Operator (Operator and higher keylock positions allow store access.)
1-Supervis (Supervisor and higher keylock positions allow store access.)
2-Engineer (Engineer and higher keylock positions allow store access.)
3-Program(Only the program has store access.)

SPLOCK (Array)
Type:
Lock:
Default:
PtRes:
Range:

E:ACCLVL
Setpoint LockIndicates the access lock for array point parameters FL, NN,
STRn and TIME.
Engr
Operator
HPM
0-Operator (Operator and higher keylock positions allow store access.)
1-Supervis (Supervisor and higher keylock positions allow store access.)
2-Engineer (Engineer and higher keylock positions allow store access.)
3-Program(Only the program has store access.)

SPLOCK (Totalizer)
Type:
Setpoint LockStores to AVTV/PVTV parameters, are checked against the
Lock:
Engr
access lock specified by SPLOCK.
Default:
PtRes: HPM
Range: 0-Operator (Operator and higher keylock positions allow store access.)
1-Supervis (Supervisor and higher keylock positions allow store access.)
2-Engineer (Engineer and higher keylock positions allow store access.)
3-Program(Only the program has store access.)

394

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SPLOFL (RegCtl)

SPLOFL (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Setpoint Low Limit Violation FlagIndicates that the SP has exceeded the
View
lower limit established by SPLOLM.
Off
HPM
Off (Low limit is not exceeded)
On (Low limit is exceeded)

SPLOLM (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Setpoint Low LimitDefines the lower limit for the SP.
Supr
NaN
HPM
SPEULO to SPHILM,
NaN
Helpful Hint: 1. Entering NaN disables limit checking by forcing SPLOLM to its extreme
value (SPEULO).
2. SPLOLM does not apply for the RampSoak algorithm.

SPOPT (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:SPOPT
Setpoint Option
Eng/PB
None
HPM
0-None (No specialized options are available)
1-TV (Target Value processing; provides a smooth transition from an existing setpoint to a desired
setpoint)
2-Asp (Advisory setpoint processing for Advisory Deviation Alarming)
Helpful Hint: 1. If component has been entered for the PNTFORM parameter, the Asp option
cannot be configured.
2. SPOPT does not apply for the RampSoak algorithm.

SPP (FBCM)
FF Param. Source:
PID: SP.Value
Type:
Real
Setpoint in PercentThe value of the current setpoint in percent.
Lock:
Prog
Default: NaN
PtRes: IOP
Range: 0.0 =< x <= 100.0, NaN

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

395

SPP (RegCtl)

SPP (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
N/A

Setpoint in Percent

SPTV (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Setpoint Target Value in Engineering Units
Oper
N/A
HPM
SPLOLM to SPHILM,
NaN
Helpful Hint: SPTV change requires SPOPT = TV.

SPTVP (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
N/A
HPM
> 0.0

Setpoint Target Value in Percent

Helpful Hint: SPTVP change requires SPOPT = TV.

SRQUTAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Average UCN Store Request Trip TimeThe average time in milliseconds


that it takes to receive a response to this nodes UCN store request.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

396

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SRQUTMAX (NIM, HPM Box)

SRQUTMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Maximum UCN Store Request Trip TimeThe maximum time in


milliseconds that it takes to receive a response to this nodes UCN store
request.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

SRSPTAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Average UCN Store Response Trip TimeThe average time in


milliseconds that it takes this node to respond to UCN store requests from
other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

SRSPTMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Maximum UCN Store Response Trip TimeThe maximum time in


milliseconds that it takes this node to respond to UCN store requests from
other nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

SSTEP(1)(2) (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

String_8
View
Spaces
HPM
N/A

Subroutine Step NameIndicates the current step of the subroutine executing


in this Process Module. A value of means that no subroutine is executing.
SSTEP(1) and SSTEP(2) display the step name of the first and second level
subroutines called from the main sequence.

SSTMT(1)(2) (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Integer
View
0
HPM
0 to 255

Subroutine Statement NumberThis parameter points to the statement


number (in the NIM sequence library) of the current subroutine. A value of 0
indicates that no subroutine is executing. The array index indicates nesting level.

HPM Parameter Reference Dictionary


Honeywell Inc.

397

ST0_OP13 (DevCtl, Digcomp)

ST0_OP13 (DevCtl, Digcomp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Eng/PB
Off
HPM
Off
On

State 0, Outputs 1 through 3Defines the value (On or Off) that is to be


written to output number 1, 2, and 3 when the OP is in State 0.

ST1_OP13 (DevCtl, Digcomp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Eng/PB
Off
HPM
Off
On

State 1, Outputs 1, 2, and 3Defines the value (On or Off) that is to be


written to output number 1, 2, and 3 when the OP is in State 1.

ST2_OP13 (DevCtl, Digcomp)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Eng/PB
Off
HPM
Off
On

State 2Outputs 1, 2, and 3Defines the value (On or Off) that is to be


written to output number 1, 2, and 3 when the OP is in State 2.

STARTFL
Type:
Lock:
Default:
PtRes:
Range:

398

Logical
Start Command FlagStarts DigIn accumulator, RegPV totalizer, or Box
Prog
Timer when flag transitions from Off to On.
Off
HPM
Off (No effect on accumulator/totalizer)
On (Allows the accumulator/totalizer to begin counting up/down)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

STATE (STI)

STATE (STI)
Type:
Lock:
Default:
PtRes:
Range:

E:STATE
Current StateIndicates the current state of the STI point.
View
N/A
HPM
2-Loading (Indicates that database loading between the STI point and the transmitter is occurring.)
3-Loadcomp (Indicates that the database transfer between the STI point and the transmitter has been
successfully completed)
4-Loadfail (Indicates that the parameter transfer between the STI point and the transmitter has not been
successfully completed)
5-Calib (Indicates that certain parameters are being calibrated at the transmitter by the STI point)
6-Calcomp (Indicates that the calibration has been successfully completed)
7-Calfail (Indicates that the calibration has not been successfully completed)
8-OK (Normal state; indicates that the STI point and the transmitter are OK. Transmitter is updating the
PV value at the STI point. STATE remains OK when the point is made inactive.)
9-DBChange (Indicates that a database mismatch between the STI point and the transmitter has been
detected. Transmitter is not updating the PV value at the STI point. STATE remains DBChange when
the point is made inactive.)

STATE (Timer, DigIn)


Type:
Lock:
Default:
PtRes:
Range:

E:STATE
View
Stopped
HPM
0-Stopped
1-Running

Timer StateIndicates the current state of the timer data point.

STATE (Totalizr)
Type:
Lock:
Default:
PtRes:
Range:

E:STATE
Accumulator StateIndicates the current state of the totalizer.
View
Stopped
HPM
0-Stopped (Stopped)
1-Running (Accumulating)

STATE02
Type:
String_8
Lock:
View
Default: 1 = On
0 = Off
2 = State 2
PtRes: NIM
Range:

R610
11/99

Current StateThese parameters represent the state text (STATETXT)


descriptors as follows:
STATE0 = STATETXT(0)
STATE1 = STATETXT(1)
STATE2 = STATETXT(2); Digital Composite and DevCtl points.
Refer to the HPM Control Functions and Algorithms manual for a detailed
description of the Digital Composite point states.

N/A

HPM Parameter Reference Dictionary


Honeywell Inc.

399

STATETXT(0)(3) (DevCtl, DigIn, DigComp, Flag)

STATETXT(0)(3) (DevCtl, DigIn, DigComp, Flag)


Type:
String_8
Lock:
PtBld
Default: 0 = Off
1 = On
2 = State 2
3 = None
PtRes: NIM

State Descriptor TextDefine the states of the point using descriptors


which can have up to eight characters.
STATETXT (1) corresponds to the first ACTIVE state, or the state
corresponding to PVFL = On (direct acting) or PVFL = Off (reverse acting).
On the Group or Detail Display, it is in the upper box.
STATETXT (0) corresponds to the INACTIVE state, or the state
corresponding to PVFL = Off (direct acting) or On (reverse acting). On the
Group or Detail Display, it is the middle box for a Digital Composite or
DevCtl point. For a Digital Input point, it is the lower box.
STATETXT (2) corresponds to the second ACTIVE state. On the Group or
Detail Display for a Digital Composite or DevCtl point, it is in the lower box.
STATETXT(2) does not apply to Digital Input and Flag points. When a twostate device is configured, STATETXT(2) is internally set to $NULL.
STATETXT (3) NONE (not configurable).
STATETXT(3) does not apply to Digital Input and Flag points.

Range:

N/A
Helpful Hint: STATETXT has an access lock of View if PNTFORM = Componnt.
STATETXT (2) for State 2 applies only if NOSTATES = 3 for digital composite or
device control points.

STATETXT(0)-(2) (FBCM)
FF Param. Source:
Type:
String
Lock:
PtBld
Default: 0-Off
1-On
2-State2
PtRes: NIM
Range: N/A

None
State Descriptor TextDefine the states of the point using descriptors
which can have up to eight characters.

STATMENT (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

400

Integer
View
0
HPM
1 to 255

StatementIndicates the current statement of the sequence executing in this


process module. A statement number of 0 indicates that no statement is being
executed.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

STATTIM(0)(2) (DevCtl, DigComp)

STATTIM(0)(2) (DevCtl, DigComp)


Time
State TimeThe amount of time based on the PV that has accumulated for
(Duration)
States 0, 1, and 2 since the most recent reset of maintenance statistics.
Lock:
View
Default: 0
PtRes: HPM
Range: 0 - 4000 Days (1 second resolution)
Type:

STDBYMAN (AnalgOut, DigOut, RegCtl)


Type:
Lock:
Default:
PtRes:
Range:

Logical
Standby Manual FlagIndicates whether the associated hardware output is
View
connected to a standby manual device. It is not an indication of whether or not
Off
the output is isolated from the process.
HPM
Off (Output is not connected to standby-manual device)
On (Output is connected to standby-manual device)

STDBYSTS(1)(168)
Type:
Lock:
Default:
PtRes:
Range:

Logical
View

Standby Status FlagReturns blind record of STDBYMAN status

HPM
Off (No Standby Manual present)
On (Standby Manual is activated)

STCHGOPT (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

State Change OptionState0 passed through before entering a new state. If


command disagree alarming is not configured, the point will wait for the
number of seconds designated in the PAUSETIM parameter after State0 is
commanded. If alarming is configured, the system will wait for the PV to go
to State0 (or when the feedback timer expires) before starting the pause timer.
None (State change option is not configured)
State0 (State change option is configured)
E:$STCHGOP
Engr/PB
0-None
1-HPM

STEP (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

String_8
View
Spaces
HPM
N/A

Step NameIndicates the step name of the sequence executing in this process
module.

HPM Parameter Reference Dictionary


Honeywell Inc.

401

STKCAPRE (SECM)

STKCAPRE (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: N/A

StackCapabilitiesRecord
Stack Capabilities RecordIOP stack configuration information.
MaxDlsapAddressesSupported and MaxDlcepAddressedSupported

STI_EU (STI)
Type:
Lock:
Default:
PtRes:

E:STI_EU
Eng
InH20
HPM

Smart Transmitter Engineering UnitsSpecifies the units of measurement for


parameters LRL, LRV, URL, and URV. These units are used for display only.
For multivariable Smart Transmitters with a SENSRTYP of SFM, choose
BLANK. For multivariable slots with a SENSRTYP of SPT_DP, SPT_AP,
SPT_GP, or STT, choose the preferred STI_EU (engineering units). When
BLANK is selected the limit values URL, LRL, URV and LRV are displayed in
the base engineering units specified in the transmitter user manual.

Helpful Hint: Loading an invalid STI_EU type causes an error. An attempt to correct it from the Detail
Display is rejected as CONFIG MISMATCH. To recover, load the correct STI_EU parameter from the
PED or perform an UPLOAD from the point Detail Display.
Range:
0-InH20 (Pressure transmitterInches of water)
1-MMHG (Pressure transmitterMillimeters of mercury)
2-PSI (Pressure transmitterPounds per square inch)
3-KPA (Pressure flow transmitterKilopascals)
4-MPA (Pressure transmitterMillipascals)
5-MBar (Pressure transmitterMillibars)
6-Bar (Pressure transmitterBars)
7-G_SQCM (Pressure transmitterGrams per square centimeter)
8-KG_SQCM (Pressure flow transmitterKilograms per square centimeter)
9-MMH20 (Pressure transmitterMillimeters of water)
10-INHG (Pressure transmitterInches of mercury)
11-Deg_C (Temperature transmitterDegrees Centigrade)
12-Deg_F (Temperature transmitterDegrees Fahrenheit)
13-Deg_K (Temperature transmitterDegrees Kelvin)
14-Deg_R (Temperature transmitterDegrees Rankine)
15-MV (Temperature transmitterMillivolts)
16-V (Temperature transmitterVolts)
17-Ohms (Temperature transmitterRTD Ohms)
18-CM_HR (Magnetic flow transmitter (volume)Cubic Meters per hour)
19-Gal_HR (Magnetic flow transmitter (volume)Gallons per hour)
20-LIT_HR (Magnetic flow transmitter (volume)Liters per hour)
21-CC_HR (Magnetic flow transmitter (volume)Cubic Centimeters per hour)
22-CM_Min (Magnetic flow transmitter (volume)Cubic Meters per hour)
23-Gal_Min (Magnetic flow transmitter (volume)Gallons per minute)
24-Lit_Min (Magnetic flow transmitter (volume)Liters per minute)
25-CC_Min (Magnetic flow transmitter (volume)Cubic centimeters per minute)
26-CM_Day (Magnetic flow transmitter (volume)Cubic meters per day)
27-Gal_Day (Magnetic flow transmitter (volume)Gallons per day)
28-KGal_Day (Magnetic flow transmitter (volume)Thousands of gallons per day)
402

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

STI_EU (STI) (continued)

STI_EU (STI)

(continued)

29-BRL_Day (Magnetic flow transmitter (volume)Barrels per day)


30-CM_Sec (Magnetic flow transmitter (volume)Centimeters per second)
31-KG_HR* (Magnetic flow transmitter (mass)Kilograms per hour)
32-LBS_HR* (Magnetic flow transmitter (mass)Pounds per hour)
33-Ft_Sec (Magnetic flow transmitter (velocity)Feet per second)
34-M_Sec (Magnetic flow transmitter (velocity)Meters per second)
35-KG_Min* (Magnetic flow transmitter (mass)Kilograms per minute)
36-KG_Sec* (Magnetic flow transmitter (mass)Kilograms per second)
37-LBS_Min* (Magnetic flow transmitter (mass)Pounds per minute)
38-LBS_Sec* (Magnetic flow transmitter (mass)Pounds per second)
39-PRCNT (Percent)
40-BLANK (Blank) - Multivariable transmitter with SFM SENSRTYP
41-LBS (Pounds)
42-KG (Kilograms)
43-TONS (Tons)
44-GRAMS (Grams)
45-OZ (Ounces)
46-GAL (Gallons)
47-BRL (Barrels)
48-CUB_M (Cubic Meters)
49-LITERS (Liters)
50-MLITRES (Milliliters)
51-FL_OZ (Fluid ounce)
52-FEET (Feet)
53-METERS (Meters)
54-MM (Millimeters)
55-INCHES (Inches)
56-KG_CUM (Kilograms per cubic meter)
57-G_CUM (Grams per cubic Meter)
58-LBS_CUFT (Pounds per cubic foot)
59-LBS_CUIN (Pounds per cubic inch)
* Not implemented

STISWVER (STI)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

String_8
View
Blank
HPM
N/A

Software Revision Level of the Smart Transmitter

HPM Parameter Reference Dictionary


Honeywell Inc.

403

STITAG (STI)

STITAG (STI)
Type:
Lock:
Default:
PtRes:

String_8
Eng/PB
All Spaces
HPM

Transmitter Tag NameIdentifies the name of the Smart Transmitter to the


system and on displays, reports, and logs.

Helpful Hint: For multivariable transmitters, an identical STITAG must be entered for each active slot
related to that transmitter. The IOP uses the number of identical STITAG names to calculate the number
of PVs associated with a given transmitter.
Range:

Tag name can be up to 8 characters, and the permissible character set is as follows:
Alphabetics A-Z (uppercase or lowercase)
Numerics 0-9
Embedded space characters are allowed.

STOPFL
Type:
Lock:
Default:
PtRes:
Range:

Logical
Stop Command FlagStops the DigIn accumulator, RegPV totalizer, or Box
Prog
Timer when flag transitions from Off to On.
Off
HPM
Off (No effect on the accumulator/totalizer)
On (Stops the accumulator/totalizer from counting up/down)

STR8(1)(16,384) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

404

String_8
Oper
Spaces
HPM
N/A

Box String VariablesThe upper bound limit of this array is determined by the
NSTRING Box parameter. The LCN index limit is 4095, while no limit exists
for the UCN. Array points may be used to address strings with an index greater
than 4095.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

STR8(1)(16) (ProcMod)

STR8(1)(16) (ProcMod)
Type:
Lock:

String_8
Determined by
SPLOCK
parameter
Default: Spaces
PtRes: HPM
Range: N/A

Local String VariablesEach Process Module point has 16 local STR8


variables that are different from the HPM Box STR8 variables.

STR16(1)(8) (ProcMod)
Type:
Lock:

String_16
Determined by
SPLOCK
parameter
Default: Spaces
PtRes: HPM
Range: N/A

Local String VariablesEach Process Module point has 8 local STR16


variables that overlay the local STR8 variables [for example,
STR16(1)=STR8(1) concatenated with STR8(2)].

STR32(1)(4) (ProcMod)
Type:
Lock:

String_32
Determined by
SPLOCK
parameter
Default: Spaces
PtRes: HPM
Range: N/A

Local String VariablesEach Process Module point has four local STR32
variables that overlay the local STR8 variables.

STR64(1)(2) (ProcMod)
Type:
Lock:

String_64
Determined by
SPLOCK
parameter
Default: Spaces
PtRes: HPM
Range: N/A

R610
11/99

Local String VariablesEach Process Module point has two local STR64
variables that overlay the local STR8 variables [for example,
STR64(1)=STR8(1-8)].

HPM Parameter Reference Dictionary


Honeywell Inc.

405

STR8(i) (Array)

STR8(i) (Array)
Type:
Lock:

String_8
Array Point String Variables8-character string variables that are mapped to
Determined by the Array point. The number of variables is dependent on the NSTRING and
STRLEN variables.
SPLOCK
parameter
Default: N/A
PtRes: HPM
Range: 1 ` i ` (Array parameter NSTRING)/(8/STRLEN)

STR16(i) (Array)
Type:
Lock:

String_16
Array Point String Array Variables16-character string variables that are
Determined by mapped to the Array point. These variables overlay the STR8 variables.
SPLOCK
parameter
Default: N/A
PtRes: HPM
Range: 1 ` i ` (Array parameter NSTRING)/(16/STRLEN)

STR32(i) (Array)
Type:
Lock:

String_32
Array Point String Variables32-character string variables mapped to the
Determined by Array point that overlay the STR8 variables.
SPLOCK
parameter
Default: N/A
PtRes: HPM
Range: 1 ` i ` (Array parameter NSTRING)/(32/STRLEN)

STR64(i) (Array)
Type:
Lock:

String_64
Array Point String Variables64-character string variables mapped to the
Determined by Array point that overlay the STR8 variables.
SPLOCK
parameter
Default: N/A
PtRes: HPM
Range: 1 ` i ` (Array parameter NSTRING)/(64/STRLEN)

406

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

STRDESC (Array)

STRDESC (Array)
Type:
Lock:
Default:
PtRes:
Range:

String_64
PtBld
Spaces
HPM
N/A

String Array Descriptor64-character string describing the Array point string


data.

STRLEN (Array)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
8
HPM
8, 16, 32, 64

Array Point String LengthIndicates the length of the configured string (with
the STRSTIX and NSTRING parameters) displayed on the Array Point Detail
display. Strings can be accessed by STR8, STR16, STR32 or STR64 regardless
of this value.

STRLEN (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

Integer
PtBld
8
HPM
8, 16, 32, 64

Process Module String LengthIndicates the displayed string length on the


Process Module Detail display. Strings can still be accessed by STR8, STR16,
STR32, or STR64 regardless of this value.

STRSTIX (Array)
Type:
Lock:
Default:
PtRes:
Range:

Real
String Array Start IndexDefines the string array start index in Box STR8
variables, or the Serial Interface-connected device.
PtBld
0
HPM
0 to Box parameter NSTRING (When EXTDATA`IO_STR, 0 indicates no strings are configured)
0 to 99,999 (When EXTDATA=IO_STR, 0 can be a valid device index)

STRTFAIL(1)(6)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

String_2
View

Startup/Failover Information

HPM
Hexadecimal characters 00 to FF

HPM Parameter Reference Dictionary


Honeywell Inc.

407

STSMSG

STSMSG
Type:
Lock:
Default:
PtRes:
Range:

E:MSGTXT Status MessageA self-defining enumeration of the MSGTXT parameter that


Oper
provides additional descriptive information regarding the red tag, batch state, or
MSGTXT(0) device state.
HPM
MSGTXT(0) to MSGTXT(15)

SUMSLTSZ (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

Total Configured Memory for Sequence ProgramsThis parameter equals


the sum of all Process Module SEQSLTSZ parameters, and is shown on the
HPMM Control Configuration display.

SUSPSTAT (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

E:$SUSPST
View
None
HPM
0-None
2-Feedback
3-Wait
4-ConfMsg
5-InputMsg

Suspend State

SUSPTIME (ProcMod)
Type:
Lock:
Default:
PtRes:
Range:

408

Integer
Suspension TimerThe remaining time (in minutes) before the sequence
program resumes execution. This timer is started when a sequence program
View
executes a wait statement.
0
HPM
0 to 32, 767 minutes

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SVALDB (DevCtl)

SVALDB (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:PVALDB
SECVAR Alarm DeadbandThe deadband for the SECVAR alarm.
Engr/PB
One
HPM
0-Half (1/2 of 1% of Engineering Unit range)
1-One (1% of Engineering Unit range)
2-Two (2% of Engineering Unit range)
3-Three (3% of Engineering Unit range)
4-Four (4% of Engineering Unit range)
5-Five (5% of Engineering Unit range)
6-EU (Value is defined by SVALDBEU parameter)

SVALDBEU (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
SECVAR Alarm Deadband in Engineering UnitsIndicates the alarm
deadband in engineering units when the SVALDB parameter = EU.
Engr/PB
0.0
HPM
Allowable Engineering Units

SVDESC (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

String_8
SECVAR DescriptorDefines the SECVAR parameter or secondary variable
PtBld
descriptor.
Blank
HPM
8 Character String

SVEUDESC (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

String_8
SECVAR Engineering Unit DescriptorDefines the engineering unit
PtBld
descriptor for the SECVAR parameter or secondary variable descriptor.
Blank
HPM
8 Character String

SVEUHI (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Engr/PB
NaN
HPM
<> NaN

SECVAR Range HighDefines the high engineering unit range for the
SECVAR parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

409

SVEULO (DevCtl)

SVEULO (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Engr/PB
NaN
HPM
<> NaN

SECVAR Range LowDefines the low engineering unit range for the
SECVAR parameter.

SVHHFL (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
SECVAR High-High Alarm Flag
View
Off
HPM
Off (SECVAR parameter is below the SVHHTP parameter minus the deadband)
On (SECVAR parameter has exceeded the SVHHTP parameter)

SVHHPR (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPIOR
SECVAR High-High Alarm Priority
Engr
Low
NIM
JnlPrint (Alarm is historized, reported to printer, but not annunciated)
Printer (Reported to printer only)
Emergncy (Reported to all alarm summary displays)
High (Reported to Area Alarm Summary Display and Unit Alarm Summary Display)
Low (Reported to Unit Alarm Summary Display)
Journal (Logged but not reported to Universal Stations)
NoAction (Alarm is not reported to the system)

SVHHTP (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
SECVAR High-High Alarm Trip PointNo alarms are generated when this
parameter is set to NaN.
Supr
NaN
HPM
> SVHITP or NaN

SVHHTPP (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

410

Real
Supr
NaN
HPM
0 to 100

SECVAR High-High Trip Point PercentThe SECVAR High-High Trip


Point in terms of engineering units in percent.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SVHIFL (DevCtl)

SVHIFL (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Logical
SECVAR High Alarm FlagThis flag is set when the SECVAR exceeds
SVHITP and is reset when SECVAR is below SVHIFL minus deadband.
View
Off
HPM
Off (SECVAR parameter is below SVHIFL minus the deadband)
On (SECVAR parameter has exceeded SVHIFL)

SVHIPR (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:ALPRIOR SECVAR High Alarm Priority


Engr
Low
NIM
JnlPrint (Alarm is historized and reported to the printer but not annunciated)
Printer (Alarm is reported to the printer but not historized and not annunciated)
Emergncy (Alarm is historized, annunciated, and reported to all alarm summary displays)
High (Alarm is historized, reported to Area Alarm Summary Display and Unit Alarm Summary
Display)
Low (Alarm is historized, reported to the Unit Alarm Summary Display, and annunciated)
Journal (Alarm is historized but not reported to Universal Stations and not annunciated)
NoAction (Alarm is not reported to the system and not annunciated)

SVHITP (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
SECVAR High Alarm Trip PointWhen this parameter is set to NaN, no
alarms are generated.
Supr
NaN
HPM
> SVEULO or NaN

SVHITPP (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Real
Supr
NaN
HPM
0 to 100

SECVAR High Alarm Trip Point PercentThe SECVAR High Trip Point in
terms of engineering units percent.

HPM Parameter Reference Dictionary


Honeywell Inc.

411

SVP (DevCtl)

SVP (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
0 to 100

SECVAR in Percent of Engineering RangeThe percentage for this


parameter is calculated from the SECVAR parameter, using both the SVEVHI
and SVELVO parameters.

SVPEAK (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
Real or NaN

Peak Value of SECVARIndicates the highest value of the SECVAR


parameter since the device changed from state 0.

SVSRC (DevCtl)
Type:

Universal
SECVAR Input ConnectionSpecifies input connection to which the current
values of Device Control inputs are supplied. The connection can be specified
Ent.Prm
using the "Tagname.Parameter" format or the hardware reference address
Lock:
PtBld
format Refer to the HPM Control Functions and Algorithms manual for a
Default: Null
detailed description.
PtRes: HPM
Range: Use Tagname.Parameter for tagged points where Tagname can be up to 16 characters and the permissible
character set is as follows:
Alphabetics A-Z (uppercase only)
Numerics 0-9 (an all numeric tag name is not allowed)
Underscore (_) cannot be used as the first character or the last character, and consecutive
underscores are not allowed.
Embedded space characters are not allowed.
An * is used to default to this point's tag name.
Parameter name can be up to eight characters and must be a legitimate parameter name.
Some possible input-connection sources are
a."Logic slot Tagname.NN(nn)" where nn = 18
b."ProcMod slot Tagname.NN(nnn)" where nnn = 180
c."Box Numerics slot Tagname.NN where nnnnn = 1-16,384
d."!Box.FL(nnnn)" for a box flag that resides in the same box where nnnn = 116,384
Use the hardware reference address !MTmmSss.Parameter for untagged or tagged points where
MT is the IOP type, such as AI (Analog Input)
mm is the IOP Card number (140)
The letter "S" is a constant
ss is the slot number on the IOP Card (refer to SLOTNUM parameter)
Parameter name can be up to eight characters and must be a legitimate parameter name.

412

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SVTV (DevCtl)

SVTV (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Secondary Variable Target ValueIndicates the normal or operating setpoint
for the SECVAR parameter.
Oper
NaN
HPM
SVEULO to SVEUHI

SVTVP (DevCtl)
Type:
Lock:
Default:
PtRes:
Range:

Real
Oper
NaN
HPM
0 to 100

Secondary Variable Target Value in PercentIndicates the normal or


operating setpoint for the SECVAR parameter as a percent.

SWTCHACT (1)(40) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Logical
View
On
HPM
On-Active
Off-Inactive

IOP SynchronizationWhen this parameter is Off (inactive), the backup


request line from the IOP's partner is not asserted. When this parameter is On
(active), the backup request line from the IOP's partner is asserted.

SYNCHSTS(1)(40) (HPM Box)


Type:
Lock:
Default:
PtRes:

E:$SYNCHST
View
None
HPM

Range:

0-OK - (the secondary is synchronized with the


primary and can provide backup if necessary.)
1-WARNING - (database inconsistency detected
but secondary can probably provide backup).
2-FAIL - (HPMM has tried to resynchronize but
has not succeeded or, secondary has also failed).

R610
11/99

Primary/secondary Database Synchronization Status. It is set to


WARNING when a database inconsistency is first detected, but the secondary
appears capable of providing backup. It changes to FAIL when the HPMM
has tried to resync but does not succeed or a secondary failure prevents
synchronization.
nn = 140 corresponds to the 40 logical I/O modules.
Applies to primary IOP only.

HPM Parameter Reference Dictionary


Honeywell Inc.

413

T (FlowComp)

-TT (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
1.0
HPM
> 0.0

Temperature InputIndicates the measured actual temperature.

T0 (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
N/A

Zero Reference for TemperatureT0 is the zero reference temperature input


and it is in the same engineering units as the T (measured actual temperature)
input. T0 is typically -459.69 degrees F or -273.15 degrees C. Enter the
absolute value of the temperature.

T1
Type:
Lock:
Default:
PtRes:
Range:

Real
Integral Time in MinutesDefines the integral time constant in
Supr
minutes-per-repeat.
0.0 minutes
HPM
0.0 to 1440.0 minutes
Helpful Hint: Integral action can be disabled by setting T1 equal to 0.0.

T2
Type:
Lock:
Default:
PtRes:
Range:

Real
Derivative Time in MinutesDefines the derivative time constant.
Supr
0.0 minutes
HPM
0.0 to 1440.0 minutes
Helpful Hint: Derivative action can be disabled by setting T2 equal to 0.0

TBNMVW3 TBNMVW4 (FBCM)


FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: 1
PtRes: IOP
Range: 1,2

414

Number of VIEW_3, Number of VIEW_4


Transducer Block Number View3 and View4The numnber of
transducer block view3 and view4 objects

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

TBODIDX (FBCM)

TBODIDX (FBCM)
FF Param. Source:
Type:
Real
Lock:
PtBld
Default: 0
PtRes: IOP
Range:

Starting OD index of Transducer Block


Transducer Object Dictionary IndexDefines the start of the
transducer block information in the object dictionary.
PECM also uses TBODIDX for device checkpointing or during
configuration. Since PECM is configured before FBCM, FBODIDX
would probably be a PECM parameter and FBCM would access it.
OD Index Valid Range

TBTYPE (FBCM)
FF Param. Source:
None
Type:
E:$TBTYPE Transducer TypeTransducer Block Type. Represents one of the 15
standard transducer block types.
Lock:
PtBld
Default: NOTCNFG
PtRes: IOP
Range: 0-NOTCNFG (Transducer is not configured)
1-PRESBAS (Standard Pressure Basic Transducer)
2-PRESCMPLX (Standard Pressure Complex Transducer)
3-TEMPBAS (Standard Temperature Basic Transducer)
4-TEMP2SENS (Standard Temperature Two-Sensor Transducer)
5-TEMPCMPLX (Standard Temperature ComplexTransducer)
6-LVLBAS (Standard Radar Level Basic Transducer)
7-LVLCMPLX (Standard Radar Level Complex Transducer)
8-FLOWBAS (Standard Flow Basic Transducer)
9-FLOWCMPLX (Standard Flow Complex Transducer)
10-BPOSBAS (Basic Position Basic Transducer)
11-BPOSCMPLX (Basic Position Complex Transducer)
12-APOSBAS (Advanced Position Basic Transducer)
13-APOSCMPLX (Advanced Position Complex Transducer)
14-DPOSBAS (Discrete Position Basic Transducer)
15-DPOSCMPLX (Discrete Position Complex Transducer)

TCRNGOPT
Type:
Lock:
Default:
PtRes:
Range:

E:$TCRNGOP
Thermocouple Range OptionDefines the thermocouple range option.
Eng/PB
Applies only if a thermocouple (TC) sensor type is used for this data point.
Normal
HPM
0-Normal (Use PVEXEULO's normal range table)
1-Extended (Use PVEXEULO's extended range table)
Helpful Hint: TCRNGOPT configuration requires IOTYPE = LLAI, LLMUX, or RHMUX and
SENSRTYP = Thermcpl. Refer to parameter PVEXEULO.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

415

TD (VdtLdLag)

TD (VdtLdLag)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr
0.0
HPM
> 0.0 minutes

Total Dead Time in MinutesDefines the fixed delay time in minutes for
equation B, and the actual variable delay time in minutes for equations C and D.

TF
Type:
Lock:
Default:
PtRes:
Range:

Real
PV Filter Lag Time in MinutesDefines the filtering time lag to be used after
Supr
the PV range has been checked. A value of 0.0 specifies that the PV is not
0.0 minutes
delayed.
HPM
0.0 to 60.0 minutes

TIERTYPE (HPM Box)


Type:
E:$TIERTYP
Lock:
View
Default:
PtRes: HPM
Range:

HPMM Tier Type

TIME(1)(4095) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Time
Oper
0 seconds
HPM
N/A

Box Time VariablesThe upper limit of this array is determined by the


NTIME parameter. The LCN index limit is 4,095, while the limit on the UCN is
4096. Array points may be used to address Times with an index greater than
4095.

TIME(i) (Array)
Type:
Lock:

Time
Array Point Time VariablesTimes are mapped from the HPM Box defined
Determined by by the TIMESTIX and NTIME parameters.
SPLOCK
parameter
Default: N/A
PtRes: HPM
Range: 1 ` i ` Array parameter NTIME

416

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

TIME(1)(4) (ProcMod)

TIME(1)(4) (ProcMod)
Type:
Lock:

Time
Determined by
SPLOCK
parameter
Default: 0 seconds
PtRes: HPM
Range: N/A

Local Time VariablesFour local Time variables are available in each Process
Module point. These variables are different than the HPM Box Time variables.

TIMEBASE (Timer)
Type:
Lock:
Default:
PtRes:
Range:

E:TIMEBASE
Engr
Seconds
HPM
0-Seconds
1-Minutes

Time BaseDefines the time base to be used for the Timer data point.

TIMEBASE (Totalizr, PI)


Type:
Lock:
Default:
PtRes:
Range:

E:TIMEBASE
Totalizer Time BaseDefines whether time base is in seconds, minutes, or
Eng/PB
hours.
Minutes
HPM
0-Seconds (PV and Setpoint engineering units (gallons, etc.) per second)
1-Minutes (PV and Setpoint engineering units (gallons, etc.) per minute)
2-Hours (PV and Setpoint engineering units (gallons, etc.) per hour)

TIMEDESC (Array)
Type:
Lock:
Default:
PtRes:
Range:

String_64
PtBld
Spaces
HPM
N/A

Time Array DescriptorSixty four-character string describing Time data.

TIMESECS(1)(240) (Array)
Type:
Lock:

Time
Array Point Time VariablesTimes mapped from the HPM box defined by
Determined
TIMESTIX and NTIME parameters.
by SPLOCK
parameter
Default: N/A
PtRes: HPM
Range: 1 ` i ` NTIME Array parameter

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

417

TIMESTIX (Array)

TIMESTIX (Array)
Type:
Lock:
Default:
PtRes:
Range:

Real
Time Array Start IndexDefines the Time data start index in the Box
PtBld
Time variables.
0
HPM
0 to Box parameter NTIME (0 indicates there are no Times configured for this point)

TIMESYNC (UCN)
Type:
Lock:
Default:
PtRes:
Range:

E:ENBLSTAT
Timesynch ControlDefines whether SOE timesynch can be performed by
PtBld
this NIM or NIM pair. Normally, the NIM with the lowest address is
Disable
configured for this function.
NIM
Enable (This NIM or NIM pair is able to perform SOE time synchronization)
Disable (This NIM or NIM pair does not perform SOE time synchronization, but can receive and
report SOE events)

TLD (VdtLdLag)
Type:
Lock:
Default:
PtRes:
Range:

Real
Lead Time Constant in MinutesDefines the lead-compensation time
Supr
constant in minutes. A 0 (zero) entry specifies no lead compensation.
0.0 minutes
HPM
-1440.0 to 1440.0 minutes

TLG1, TLG2 (VdtLdLag)


Type:
Lock:
Default:
PtRes:
Range:

Real
Lag Time Constant
Supr
0.0 minutes
HPM
0.0 to 1440.0 minutes (0 specifies no lag compensation)

TMCMD(1)(64) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

418

E:COMMAND
Timer CommandAn array of commands issued to the 64 Timer data
Oper
points.
N/A
HPM
0-None (A command has not been issued to the timer)
1-Start (Starts the timer)
2-Stop (Stops the timer)
3-Reset (Resets the timer to 0)
4-RestStrt (Resets the timer to 0, and starts the timer)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

TMPV(1)(64) (Timer)

TMPV(1)(64) (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

Timer PVIndicates the current (elapsed) time of the Timer data point in
seconds or minutes.

TMRV(1)(64) (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Integer
View
0
HPM
>0

Timer RVIndicates the remaining time (TMSP minus TMPV) for the Timer
data point.

TMSO(1)(64) (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Logical
Timer Status OutputIndicates the current state of the timer output.
View
Off
HPM
Off (TMPV ` TMSP; elapsed time has not reached the preset time)
On (TMPV = TMSP; elapsed time has reached the preset time)

TMSP(1)(64) (Timer)
Type:
Lock:
Default:
PtRes:
Range:

Integer
Oper
0
HPM
0 to 32000

Timer SetpointDefines the preset time of the Timer data point, in seconds or
minutes.

TMST(1)(64) (Timer)
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

E:STATE
Timer StateIndicates the current state of the Timer data point.
View
Stopped
HPM
0-Stopped (Timer is currently stopped)
1-Running (Timer is currently running)

HPM Parameter Reference Dictionary


Honeywell Inc.

419

TMTB(1)(64) (Timer)

TMTB(1)(64) (Timer)
Type:
Lock:
Default:
PtRes:
Range:

E:TIMEBASE
Engr
Seconds
HPM
0-Seconds
1-Minutes

Timer Time BaseDefines the time base of the timer.

TOTLUAVG (1) - (2) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
0 - 100

Average IOL Utilization (in per cent) by the HPM, per I/O Link (total
utilization by the Comm and Control CPUs)

TOTLUMAX (1) - (2) (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
0.0
HPM
0 - 100

Maximum IOL Utilization (in per cent) by the HPM, per I/O Link (total
utilization by the Comm and Control CPUs)

TRACKING
Type:
Lock:
Default:
PtRes:
Range:

Logical
Selected Input TrackingAllows the selected input to be changed without
Eng/PB
bumping the output.
Off
HPM
Off (Tracking disabled)
On (Tracking is to be used)
Helpful Hint: If On, causes nonselected inputs to track the selected input.

TRANTIM02 (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes:
Range:

420

Time
View
0
HPM
Time Stamp

Transition TimeThe date and time of the most recent transition to each state
based on the PV.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

TRATAVG (NIM, HPM Box)

TRATAVG (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Average UCN Transaction Trip TimeThe average UCN transaction trip


time in milliseconds for both fetch and store responses from this node to other
UCN nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays

TRATMAX (NIM, HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Maximum UCN Transaction Trip TimeThe maximum UCN transaction


trip time in milliseconds for both fetch and store responses from this node to
other UCN nodes.

Helpful Hint: This statistic can be viewed on the Toolkit Displays.

TRFB (PidErfb)
Type:
Lock:
Default:
PtRes:
Range:

Real
View
NaN
HPM
N/A

Tracking Feedback Input in Engineering UnitsIndicates the value of the


PV or SP of another data point that is receiving its setpoint from this data point.

TSCOMP
Type:
Lock:
Default:
PtRes:
Range:

Time
View
0
HPM
N/A

Time Stamp, CL Source Compatibility Specifies the CL Source


compatibility time stamp (CL object header)

TSSRC
Type:
Lock:
Default:
PtRes:
Range:

R610
11/99

Time
View
0
HPM
N/A

Time Stamp, CL SourceSpecifies the CL Source time stamp (CL object


header)

HPM Parameter Reference Dictionary


Honeywell Inc.

421

TSTS (FlowComp)

TSTS (FlowComp)
Type:
Lock:
Default:
PtRes:
Range:

E:PVVALST
Temperature Input Value StatusStatus of the T input value.
View
Normal
HPM
0-Bad (Value is bad and replaced with NaN)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

TSUNICHG
Type:
Lock:
Default:
PtRes:
Range:

Time
View
0
HPM
N/A

Time Stamp, Unit ChangeSpecifies the CL Unit Change time stamp (CL
object header)

TVPROC (RegCtl)
Type:
Lock:
Default:
PtRes:
Range:

E:TVPROC
Target Value Processor State
Oper
Off
HPM
0-Off (No target value processing)
1-Preset (Set up setpoint target value and ramp time)
2-Run (Perform ramping function)
Helpful Hint: TVPROC applies only if SPOPT = TV.

422

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

UCNRECHN (HPM Box, NIM)

-UUCNRECHN (HPM Box, NIM)


Type:
Lock:
Default:
PtRes
Range:

E:$RECCHN
View
ChannelA
HPM, NIM
0-ChannelA
1-ChannelB

UCN Receive ChannelIndicates the channel to which the node is listening.

UCNSCANT (HPM Box)


Type:
Lock:
Default:
PtRes:
Range:

Real
Eng/PB
0.5
HPM
0.5, 1.0

Peer-to-Peer Scan Period in seconds

UCNSFREV
Type:
Lock:
Default:
PtRes

Integer
View
N/A
HPM

UCN Software Revision

UCNSFVER
Type:
Lock:
Default:
PtRes

R610
11/99

Integer
View
N/A
HPM

UCN Software Version

HPM Parameter Reference Dictionary


Honeywell Inc.

423

UCNWRTLK (HPM Box)

UCNWRTLK (HPM Box)


Type:
E:
HPM Write LockoutWhen HPM Write Lockout is set to On, all
Writes to the HPM (except writes to UCNWRTLK and some IOL
UCNWRTL
parameters) are locked out including peer-to-peer writes. All
Lock:
Eng
parameter reads are allowed as well as cable swaps, HPMM swaps and
Default:
WrtLkOff
IOP swaps.
PtRes:
HPM
Range: 0-WrtLkOff - (Write Lock Off, UCN node is read/write)
1-WrtLkOn - (Write Lock On, UCN node is read only)
Helpful Hint: Write Lockout must be set to Off before any changes are made to configuration, modes,
or setpoints. The state of UCNWRTLK can only be changed when the HPM is either in RUN or
RUNSOFTFAIL state.
UCNWRTL can be changed (under Engineer Key Level) from the HPM Write Lock Control display.
Refer to the HPM Implementation Guidelines for more information.

UNCMDFL (DevCtl, DigComp)


Type:
Lock:
Default:
PtRes
Range:

Logical
Uncommanded Change Alarm FlagIndicates whether an uncommanded
change has been detected in the field device. (Field device has changed its state
View
without a command.)
Off
HPM
Off (No uncommanded change alarm)
On (Uncommanded change alarm has been detected by this point)

UNIT
FF Param. Source:
Type:
String_2
Lock:
PtBld
Default: N/A
PtRes
NIM

None
Unit IdentifierDefines the process unit to which this point is assigned. The
unit identifier is originally assigned during network configuration, and it appears
in displays and listings throughout the system.
Restriction: Two characters are required; blanks are not allowed. For example,
unit 3 must be entered as 03.
CL and Picture Editor An integer is returned. This number is equivalent to
the unit position in the Unit Names configuration list.

Range: A-Z, 0-9 (up to 100 unit IDs can be configured)

UPGRADE (UCN)
Type:
Lock:
Default:
PtRes
Range:

424

E:UPGRADE NIM Upgrade Status


Oper
OK
NIM
OK (NIM has not been upgraded and is OK)
Upgrade (NIM is upgraded and is questionable)

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

URL (STI)

URL (STI)
Type:
Lock:
Default:
PtRes:

Real
Eng/View
NaN
HPM

Upper Range LimitIndicates the upper range limit of the PV at the Smart
Transmitter. This limit is a fixed limit and cannot be changed. Refer to the
description of the STI_EU parameter for the URL engineering units. During
configuration, the value entered for this parameter must agree with the URL
value of the transmitter. Although any value can be entered during
configuration, a database mismatch will occur when the point is put on-process
because the transmitters URL value and the STI IOPs URL value are not the
same. If the values are not the same, the STATE parameter value becomes
DBChange and PVSTS becomes Bad. Refer to URL in the PM/APM Smartline
Transmitter Integration Manual for more information.
The corresponding LRL parameter is not a configurable parameter at the
Universal Station.
The upper range limits for the Smart Transmitters are as follows:
For the ST3000 Smart Pressure Transmitters (Spt_Dp, Spt_Gp and Spt_Ap):
Xmtr Range

URL (In H2O)

400 inH2O
600 inH2O
780 mmHga
100 PSI
200 PSI
500 PSI/A
1500 PSI
2000 PSI
3000 PSI
6000 PSI
10000 PSI

400.0
600.0
400.0
2768.0
5536.13
13840.34
41521.0
55361.35
83042.02
166084.0
276806.7

For the STT3000 Smart Temperature Transmitter (STT):

R610
11/99

Sensor Type
(PVCHAR)

URL
(in Degrees C except where noted)

Linear (mV)

1000 mV

Thermocouples:
B
E
J
K
NiNiMoTC
N
R
S
T
W5W26TC
W3W25TC

1820
1000
1200
1370
1300
1300
1760
1760
400
2300
2300

HPM Parameter Reference Dictionary


Honeywell Inc.

425

URL (STI) (continued)

URL (STI) (continued)


RTDs:
Cu10RTD
Cu25RTD
DINRTD
JISRTD
NicklRTD
Pt200
Pt500
RHRad
RTD (ohms)

250
250
850
640
150
850
850
1800
4000

For the MagneW 3000 Magnetic Flowmeter (Sfm):


URL (in meters3/hour) =

pD 2
x 3600 x (N + 1)
4x106

where: D = the detector diameter in millimeters as follows: 2.5, 5, 10, 15, 25,
40, 50, 80, 100, 150, 200, 300, 350, 400, 500, 600, or 700
N = the number of dummy submerged detectors, from 0 to 9
Range:

N/A, NaN

URV (STI)
Type:
Lock:
Default:
PtRes:
Range:

Real
Supr/View
NaN
HPM
N/A, NaN

Upper Range ValueDefines the upper end of the operating range for the
PVRAW value. Refer to the description of the STI_EU parameter for the URV
engineering units.
Although the following maximum values can be entered, values greater than the
URL are not recommended and accuracy is not guaranteed in such cases.
For a pressure transmitter (Spt): URVmax = 2.0 x URL
For a temperature transmitter (Stt): URVmax = 2.0 x URL
For a magnetic flow transmitter (Sfm): URVmax = 12.0 x URL
This parameter is a view-only parameter when the STI point execution state
PTEXECST is Active (indicating that changes cannot be made in this parameter
value from the Universal Station).

426

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

US16(1-16) (FBCM, PECM)

US16(1-16) (FBCM, PECM)


FF Param. Source:
User configured
IntegersArrayed parameter of integers mapped from FF parameters.
Type:
Integer
Lock:
Configurable
Default: 0
PtRes: FF DEVICE
Range: 0 65535
Helpful Hint: These parameters are mapped by the TPS Builder from manufacturers supplied
parameters or other fieldbus parameters not already mapped.

US32(1-16) (FBCM, PECM)


FF Param. Source:
User configured
IntegersArrayed parameter of 32-bit integers mapped from FF
Type:
Integer
Lock:
Configurable parameters.
Default: 0
PtRes: FF DEVICE
32
Range: 0 4294967295 (which is equivalent to 2 1).
Helpful Hint: This value is displayed in hexadecimal form. These parameters are mapped by the TPS
Builder from manufacturers supplied parameters or other fieldbus parameters not already mapped.

US8 (1-16) (FBCM, PECM)


FF Param. Source:
Type:
Integer
Lock:
Configurable
Default: 0
PtRes: FF DEVICE
Range: 0-255

User configured
FlagArrayed parameter of booleans or bytes mapped from FF
parameters. The FF information is dependent on the parameter to
which it is mapped.

Helpful Hint: These parameters are mapped by the TPS Builder from the device manufacturers
supplied parameters or other fieldbus parameters not already mapped.

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

427

USERID (Array, DevCtl, DigComp, ProcMod, RegCtl, RegPV)

USERID (Array, DevCtl, DigComp, ProcMod, RegCtl,


RegPV)
Type:
Lock:
Default:
PtRes
Range:

String_16
Oper
Dashes
HPM

User ID ReservationThe user ID that currently has reserved this point. The
User ID can be changed by either a point, program, or operator. The operator
can overwrite the USERID parameter at anytime. A program can store a
nonblank string in this parameter only if it is blank. If the USERID string starts
with three or more dashes (- - -), only the operator can overwrite the ID.
16 Character String

USEVFDNO (PECM)
FF Param. Source:
None
Type:
Integer
Use VFD NumberFBAP VFD index into the VFD List array used
for a PECM.
Lock:
PtBld
FBAP VFD index into the VFD List array used for this PECM.
Default: 2
PtRes: IOP
Range: 2..max of VFD_Ref_Entry

UTSDRIFT (HPM Box, NIM)


Type:
Lock:
Default:
PtRes
Range:

Integer
View
N/A
HPM, NIM

UCN Node Clock DriftIndicates the current HPMM clock drift rate,
calculated by averaging the LCN clock interval and SYNCH CLOCK interval
over multiple synchs. Averaging does not occur until UCN time
synchronization is in a steady state.

UTSNODE (HPM Box, NIM)


Type:
Lock:
Default:
PtRes

Integer
View
0
HPM, NIM

Range:

0, 1 to 64 (0 specifies No Syncher Node)

Last UCN Syncher NodeDescribes which node is the synch master or


syncher. Normally, this is the primary NIM, even though the secondary NIM
can also be the syncher. The syncher function performs periodic time
synchronization on the UCN.

UTSTBCRV (HPM Box, NIM)


Type:
Lock:
Default:
PtRes
Range:

428

String_2
View
N/A
HPM, NIM
5 to 15

TBC RevisionThe token bus controller revision number in hexidecimal


format.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

UTSTIME (HPM Box, NIM)

UTSTIME (HPM Box, NIM)


Type:
Lock:
Default:
PtRes
Range:

Time
View
N/A
HPM, NIM
N/A

Current Time in LCN NodeIdentifies the current time of day for this LCN
node, and is useful if there are multiple LCNs or UCNs.

UTSTIMST (HPM Box, NIM)


Type:
Lock:
Default:
PtRes
Range:

R610
11/99

E:$UCNTMST
Timesynch State of the UCN NodeThe state of time
synchronization for each UCN node.
View
0
HPM, NIM
0-Initial (Waiting for the first complete synch operation)
1-Failed (The maximum amount of time has elapsed and no synch operation has occurred,
or the NIM does not have a functioning EPNI board)
2-Degraded (In nonsyncher NIMs and HPMMs, an excessive amount of time has elapsed without
a complete synch operation. In HPMMs, the drift limit between the LCN and HPMM clock
has been exceeded)
3-LCN_Bad (Synch operations are taking place on a regular basis, but the NIMs clock is not
synched with the LCN)
4-LCN_OK (Synch operations are occurring regularly and the NIMs clock is properly synched
with the LCN)
5-OK (Synch operations are working in an optimal manner)

HPM Parameter Reference Dictionary


Honeywell Inc.

429

VCRLIST(1-63) (SECM)

-VVCRLIST(1-63) (SECM)
FF Param. Source:
Type:
Blind
Lock:
PtBld
Default: N/A
PtRes: IOP
Range: N/A

Network Management Information Block: VCR StaticEntry


VCR ListThis arrayed parameter contains the list of stack VCR
definitions

VENNAME (PECM, SECM)


FF Param. Source:
Type:
String
Lock:
PtBld
Default: SECM =
"HONEYWELL".
PECM = Null String
PtRes: IOP
Range: N/A

VFD Vendor name


VFD Vendor NameFor a SECM, this parameter contains the IOP
Device Vendor Name (which is not in the checkpoint). For a PECM,
this parameter contains FBAP VFD information (which is in the
checkpoint). Used for FBAP matching and display.

VFDREF (PECM, SECM)


FF Param. Source:
Type:
Real
Lock:
PtBld
Default: SECM = 2,
PECM = 0
PtRes: IOP
Range: N/A

VFD Reference in VFD_Ref_Entry


VFD Reference For a PECM, this parameter contains the FBAP
VFD reference number in the array list pointed to by the USE VFDNO
(which is in the checkpoint). For a SECM, this parameter contains the
IOP FBAP VFD Reference Number (which is not in the checkpoint).
This parameter is used for display purposes.

VFDTAG (SECM, PECM)


FF Param. Source:
Type:
String
Lock:
PtBld
Default: SECM = "IOP
FBAP VFD",
PECM = Null
String
PtRes: IOP
Range: N//A

430

VFD Tag in VFD_Ref_Entry


VFD TagVFD Tag associated with the VFD Reference in VFDREF.
For a SECM, this parameter contains the IOP FBAP VFD tag
name(which is not in checkpoint). For a PECM, this parameter contains
the FBAP VFD tag name in the array list pointed to by the
USEVFDNO (which is in checkpoint). This parameter is used for
display purposes.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

VIEW2 (FBCM, PECM)

VIEW2 (FBCM, PECM)


FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: IOP
Range: N/A

Function Block View 2


View 2 for Function Block or Resource Block

VIEW3(1-10), VIEW4(1-10) (FBCM, PECM)


FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: FF DEVICE
Range: N/A

Function Block View 3, Function Block View 4


View 3 and View 4 for Function Block or Resource Block

VIEWOUT (FBCM, PECM)


FF Param. Source:
Type:
Blind
Lock:
Oper
Default: N/A
PtRes: FF DEVICE
Range: N/A

None
View OUT This parameter is written to by an operator to modify a
single device-resident parameter from a detail display.

VS(1-16) (FBCM, PECM)


FF Param. Source:
User Configured
This is an array that contains 32-character strings that are mapped from
Type:
String
FF parameters.
Lock:
Oper
Default: Blanks
PtRes: FF DEVICE
Range: ASCII character set.

VWODIDX (FBCM, PECM)


FF Param. Source:
Function/Resource Block Header
Type:
Real
View OD IndexThis parameter contains the starting object dictionary
index of function/resource block views.
Lock:
PtBld
Default: 0
PtRes: IOP
Range: OD Index Valid Range

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

431

WARMSTRT(1)(168)

-WWARMSTRT(1)(168)
Type:
Lock:
Default:
PtRes
Range:

Logical
Warm Start Flag
View
N/A
IOP
On (Warm start executed)
Off (Cold start executed)

WEEKDAY (HPPM Box)


Type:
Lock:
Default:
PtRes
Range:

Integer
Current WeekdayThe current weekday based on LCN wall clock time.
View
N/A
HPM
1 to 7 (Sunday to Saturday)

WITHBIAS(1)(40) (HPPM Box)


Type:
Lock:
Default:
PtRes

Logical
View
ON
HPM

Range:

On (The preferred primary is the acting primary)


Off (The preferred primary is not the acting primary)

432

I/O Module Physical Bias StateON Indicates that the preferred


primary is really the acting primary; OFF indicates that it is not.
For IOPs that do not have hardware bias (e.g., HLAI, DI, etc.),
the status of ON is always returned. Applies to primary IOP only.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

X (FlowComp)

-XX (FlowComp)
Type:
Lock:
Default:
PtRes
Range:

Real
View
1.0
HPM
> 0.0

Steam Compressibility InputIndicates the measured actual steam


compressibility.

X1 (AutoMan)
Type:
Lock:
Default:
PtRes
Range:

Real
Prog
NaN
HPM
NaN

X1 Input Value to be Biased

X13 (MulDiv)
Type:
Lock:
Default:
PtRes
Range:

Real
Prog
NaN
HPM
> 0.0,
NaN

Inputs 1-3Current values of the inputs to this algorithm.

X14 (IncrSum, ORSel, RegCtl Summer)


Type:
Lock:
Default:
PtRes
Range:

Real
Prog
NaN
HPM
> 0.0,
NaN

Inputs 1-4Current values of the inputs to this algorithm.

X2 (AutoMan)
Type:
Lock:
Default:
PtRes
Range:

R610
11/99

Real
View
N/A
HPM
N/A

Bias Adjustment Input

HPM Parameter Reference Dictionary


Honeywell Inc.

433

X2 (RatioCtl)

X2 (RatioCtl)
Type:
Lock:
Default:
PtRes
Range:

Real
View
N/A
HPM
N/A

Input Number 2Indicates the value of the uncontrolled process variable.


Source should be the same as for P2 of the Calcultr algorithm, if it is being used
in conjunction with the Calcultr algorithm.

X2FILT (RatioCtl)
Type:
Lock:
Default:
PtRes
Range:

Real
View
N/A
HPM
N/A

Filtered value of the X2 input

Helpful Hint: Filter time is determined by X2TF. This filter is only active if the point is in the AUTO
or CASC mode.

X2TF (RatioCtl)
Type:
Lock:
Default:
PtRes
Range:

Real
X2 input filter lag time in minutes
Supr
0.0
HPM
0 - 60 minutes

XBLKDDID(1)-(2) (FBCM)
FF Param. Source:
Type:
Integer
Lock:
PtBld
Default: N/A
PtRes: NIM
Range: N/A

Transducer Block Header


Transducer Block Device IDA unique number which identifies the
function of the block.

XEUHI (AutoMan, IncrSum, ORSel)


Type:
Real
Lock:
Engr
Default: 100.0
(equivalent
to 100%)
PtRes
HPM
Range: > XEULO

434

X Input Engineering Unit High RangeDefines the upper limit of the value
of the X input or inputs.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

XEULO (AutoMan, IncrSum, ORSel)

XEULO (AutoMan, IncrSum, ORSel)


Type:
Real
Lock:
Engr
Default: 0.0
(equivalent
to 0%)
PtRes
HPM
Range: < XEUHI

X Input Engineering Unit Low RangeDefines the lower limit of the value of
the X input or inputs.

XSTS (FlowComp)
Type:
Lock:
Default:
PtRes
Range:

E:PVVALST
X Input Value StatusStatus of the steam compressibility input.
View
Normal
HPM
0-Bad (Value is bad and replaced with NaN)
1-Uncertn (Status of the value is uncertain)
2-Normal (Value is good)

XVIEW2 (FBCM)
FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: FF DEVICE
Range: N/A

Transducer Block View 2


Transducer Block View 2

XVIEW3(1-10), XVIEW4(1-10) (FBCM)


FF Param. Source:
Type:
Blind
Lock:
View
Default: N/A
PtRes: FF DEVICE
Range: N/A

Transducer Block View 3 and Transducer Block View 4


Transducer Block View 3 and Transducer Block View 4

XVWODIDX (FBCM)
FF Param. Source:
Transducer Block Header
Type:
Real
Transducer Block Header This parameter contains the starting
object dictionary index of transducer views.
Lock:
PtBld
Default: 0
PtRes: IOP
Range: OD Index Valid Range

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

435

YEAR (HPM Box)

-YYEAR (HPM Box)


Type:
Lock:
Default:
PtRes
Range:

436

Integer
View
N/A
HPM
1979 to 2115

Current YearThe value of the LCN date in the HPM.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FIELDBUS AND TPS PARAMETER CROSS-REFERENCES

Section 5 contains two tables that provide cross-references between TPS parametrers and Fieldbus
Foundation parameters. The first table (Table 1) is an alphabetical lising of TPS parameters versus
Fieldbus Foundation parameters. The second table (Table 2) is an alphabetical listing of Fieldbus
Foundation parameters versus TPS parameters.

5.1
TPS/FIELDBUS CROSS-REFERENCE LIST
Table 1 is a cross-reference list of TPS parameters versus Fieldbus Foundation (FF) parameters.
Table 1 TPS/FF Parameter Cross-Reference List
TPS Parameter
$AUXUNIT
$OPTOL
$SPTOL
ACTSCHVR
ACTVSCHD
ALENBST
ALMINFO
ALPRIOR
APPL
ASSOCCM
ASSOCDSP
BADPVFL
BADPVPR
BLKDDID
BLKODIDX
CASIN
CASIND
CONTCUT
CVEUHI
CVEULO
DEVHIFL
DEVHIPR
DEVLOFL
DEVLOPR
DEVSTAT
DISPTYPE
EUDESC
FBTYPE
FFALMCUR
FFBCINST
FFBCINVL
FFBCOPST
FFBCOPVL
FFCSIDST
FFCSIDVL
FFCSINST
FFCSINVL

R610
11/99

FF Parameter
None
None
None
MIB: Network Management
NMIB: LinkScheduleActivationVariable
None
None
None
None
None
None
AI: OUT.Status.Quality
None
None
Block OD index
CAS_IN
CAS_IN_D
None
PID: OUT_SCALE.EU100
PID: OUT_SCALE.EU0
ALARM_SUM.Current
DV_HI_PRI
ALARM_SUM.Current
DV_LO_PRI
None
None
None
None
ALARM_SUM.Current
BKCAL_IN.Status
BKCAL_IN.Value
BKCAL_OUT.Status
BKCAL_OUT.Value
CAS_IN_D.Status
CAS_IN_D.Value
CAS_IN.Status
CAS_IN.Value

HPM Parameter Reference Dictionary


Honeywell Inc.

437

5 Fieldbus And TPS Parameter Cross-references

Table 1 TPS/FF Parameter Cross-Reference List, continued


TPS Parameter
FF Parameter
FFDEVREV
FFDVHILM
FFDVHIPR
FFDVLOLM
FFDVLOPR
FFFFDECP
FFFFGAIN
FFFFS0
FFFFS100
FFFFUIDX
FFFFVLST
FFFFVLVL
FFGAIN
FFHHLM
FFHHPR
FFHILM
FFHIPR
FFINSTS
FFINVAL
FFLLLM
FFLLPR
FFLOLM
FFLOPR
FFMODEA
FFMODEN
FFMODEP
FFMODET
FFOEXPST
FFOEXPVL
FFOPDECP
FFOPHILM
FFOPLOLM
FFOPS0
FFOPS100
FFOPUIDX
FFOREMST
FFOREMVL
FFOUT1ST
FFOUT1VL
FFOUT2ST
FFOUT2VL
FFOUTAST
FFOUTAVL
FFOUTDST
FFOUTDVL
FFOUTSTS
FFOUTVAL
FFPTRPST
FFPTRPVL

438

VFD revision number


DV_HI_LIM
DV_HI_PRI
DV_LO_LIM
DV_LO_PRI
FF_SCALE.DecPt
FF_GAIN
FF_SCALE.EU0
FF_SCALE.EU100
FF_SCALE.UnitIndex
FF_VAL.Status
FF_VAL.Value
GAIN
HI_HI_LIM
HI_HI_PRI
HI_LIM
HI_PRI
IN.Status
IN.Value
LO_LO_LIM
LO_LO_PRI
LO_LIM
LO_PRI
MODE_BLK.Actual
MODE_BLK.Normal
MODE_BLK.Permitted
MODE_BLK.Target
OUT_EXP.Status
OUT_EXP.Value
OUT_SCALE.DecPt
OUT_HI_LIM
OUT_LO_LIM
OUT_SCALE.EU0
OUT_SCALE.EU100
OUT_SCALE.UnitIndex
OUT_REM.Status
OUT_REM.Value
OUT_1.Status
OUT_1.Value
OUT_2.Status
OUT_2.Value
OUT_ACCUM.Status
OUT_ACCUM.Value
OUT_D.Status
OUT_D.Value
OUT.Status
OUT.Value
OUT_PTRIP.Status
OUT_PTRIP.Value

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

5 Fieldbus And TPS Parameter Cross-references

Table 1 TPS/FF Parameter Cross-Reference List, continued


TPS Parameter
FF Parameter
FFPVDECP
FFPVS0
FFPVS100
FFPVSTS
FFPVUIDX
FFPVVAL
FFRATE
FFRBDST
FFRBDVL
FFRBST
FFRBVL
FFRCIDST
FFRCIDVL
FFRCINST
FFRCINVL
FFRCOPST
FFRCOPVL
FFRESET
FFROINST
FFROINVL
FFROOPST
FFROOPVL
FFSEL1ST
FFSEL1VL
FFSEL2ST
FFSEL2VL
FFSEL3ST
FFSEL3VL
FFSPHILM
FFSPLOLM
FFSPRTDN
FFSPRTUP
FFSPSTS
FFSPVAL
FFSTREV
FFTRDIST
FFTRDIVL
FFTRIPST
FFTRIPVL
FFTRVLST
FFTRVLVL
FFXDDECP
FFXDS0
FFXDS100
FFXDUIDX
FLOAT
HIGHAL
HIGHALPR
IN
IND

R610
11/99

PV_SCALE.DecPt
PV_SCALE.EU0
PV_SCALE.EU100
PV.Status
PV_SCALE.UnitIndex
PV.Value
RATE
READBACK_D.Status
READBACK_D.Value
READBACK.Status
READBACK.Value
RCAS_IN_D.Status
RCAS_IN_D.Value
RCAS_IN.Status
RCAS_IN.Value
RCAS_OUT.Status
RCAS_OUT.Value
RESET
ROUT_IN.Status
ROUT_IN.Value
ROUT_OUT.Status
ROUT_OUT.Value
SEL_1.Status
SEL_1.Value
SEL_2.Status
SEL_2.Value
SEL_3.Status
SEL_3.Value
SP_HI_LIM
SP_LO_LIM
SP_RATE_DN
SP_RATE_UP
SP.Status
SP.Value
ST_REV
TRK_IN_D.Status
TRK_IN_D.Value
OUT_TRIP.Status
OUT_TRIP.Value
TRK_VAL.Status
TRK_VAL.Value
XD_SCALE.DecPt
XD_SCALE.EU0
XD_SCALE.EU100
XD_SCALE.UnitIndex
User configured
None
None
Configurable via link object
Configurable via link object

HPM Parameter Reference Dictionary


Honeywell Inc.

439

5 Fieldbus And TPS Parameter Cross-references

Table 1 TPS/FF Parameter Cross-Reference List, continued


TPS Parameter
FF Parameter
INITREQ
KEYWORD
LASTPV
MODATTR
MODEAPPL
MODEBLKC
MODEPERM
MODNAME
MODNUM
NAME
NMODATTR
NODENUM
NODETYP
NTWKNUM
NUMSCHD
OFFNRMFL
OFFNRMPR
OP
OUT
OUTD
OUTDST
OUTST
PNTMODTY
PNTNODTY
PNTSTATE
PRILNKMS
PRIMMOD
PTDESC
PTEXECST
PTINAL
PV
PVAUTO
PVAUTOST
PVCALC
PVCLAMP
PVEUHI
PVEULO
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVFL
PVFORMAT
PVHHFL
PVHHPR
PVHIFL
PVHIPR
PVLLFL
PVLLPR

440

None
None
AI: OUT.Value
None
MODE_BLK.Permitted
MODE_BLK.Actual + MODE_BLK.Target
None
VFD model number
None
None
None
None
None
None
MIB: Network Management
ALARM_SUM.Current
DISC_PRI
AO, PID: OUT.Value
Configurable via link object
Configurable via link object
Configurable via link object
Configurable via link object
None
None
None
NMIB: PrimaryLinkMasterFlagVariable
None
None
None
None
AI: OUT.Value; PD, PID: PV.Value
AI: OUT.Value
AI: OUT.Status.Quality
AI: FIELD_VAL.Value
None
AI: XD_SCALE.EU0; PID: PV_SCALE.EU100
AI: XD_SCALE.EU0; PID: PV_SCALE.EU0
None
None
None
None
DI: OUT_D.Value
AI: OUT_SCALE.DecPt; PID: PV_SCALE.DecPt
ALARM_SUM.Current
HI_HI_PRI
ALARM_SUM.Current
HI_PRI
ALARM_SUM.Current
LO_LO_PRI

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

5 Fieldbus And TPS Parameter Cross-references

Table 1 TPS/FF Parameter Cross-Reference List, continued


TPS Parameter
FF Parameter
PVLOFL
PVLOPR
PVP
PVRAW
PVSOURCE
PVSRCOPT
PVSTS
PVTV
PVTVP
RCASIN
RCASIND
REDTAG
ROUTIN
RSSTATE
SCHDVER
SEL1
SEL2
SEL3
SLOTNUM
SO
SP
SPFORMAT
SPP
STATETXT
TBODIDX
TBTYPE
UNIT
US16
US32
US8
USEVFDNO
VENNAME
VFDREF
VFDTAG
VWODIDX
VS
VWODIDX
XBLKDDID
XVWODIDX

R610
11/99

ALARM_SUM.Current
LO_PRI
AI: OUT.Value; PID: PV.Value
None
None
None
AI: OUT.Status.Quality
PID: PV.Status.Quality
None
None
RCAS_IN
RCAS_IN_D
None
ROUT_IN
Resource block: RS_STATE
MIB: Network Management
SEL_1
SEL_2
SEL_3
None
DO: OUT_D.Value
AO, PID: SP.Value
AO, PID: PV_SCALE.DecPt
AO, PID: SP.Value
None
Starting OD index of Transducer Block
None
None
User configured
User configured
User configured
None
VFD Vendor name
VFD Reference in VFD_Ref_Entry
VFD Tag in VFD_Ref_Entry
User configured
Function/Resource Block Header
Transducer Block Header
Transducer Block Header

HPM Parameter Reference Dictionary


Honeywell Inc.

441

5 Fieldbus And TPS Parameter Cross-references

5.2
FIELDBUS/TPS CROSS-REFERENCE LIST
Table 2 is a cross-reference list of FF parameters versus TPS parameters.
Table 2 FF/TPS Parameter Cross-Reference List
FF Parameter
AI: FIELD_VAL.Value
AI: OUT.Status.Quality
AI: OUT.Status.Quality
AI: OUT.Status.Quality
PID: OUT.Status.Quality
AI: OUT.Value
AI: OUT.Value
AI: OUT.Value; PD, PID:
AI: OUT.Value; PID:
AI: OUT_SCALE.DecPt;
AI: XD_SCALE.EU0;
AI: XD_SCALE.EU0;
ALARM_SUM.Current
ALARM_SUM.Current
ALARM_SUM.Current
ALARM_SUM.Current
ALARM_SUM.Current
ALARM_SUM.Current
ALARM_SUM.Current
ALARM_SUM.Current
AO, PID: OUT.Value
AO, PID:
AO, PID: SP.Value
AO, PID: SP.Value
BKCAL_IN.Status
BKCAL_IN.Value
BKCAL_OUT.Status
BKCAL_OUT.Value
Block OD index
CAS_IN
CAS_IN.Status
CAS_IN.Value
CAS_IN_D
CAS_IN_D.Status
CAS_IN_D.Value
Configurable via link
Configurable via link
Configurable via link
Configurable via link
Configurable via link
Configurable via link
DI: OUT_D.Value
DISC_PRI
DO: OUT_D.Value
DV_HI_LIM

442

TPS Parameter
PVCALC
PVAUTOST
BADPVFL
PVSTS
PVAUTO
LASTPV
PV
PVP
PVFORMAT
PVEULO
PVEUHI
FFALMCUR
OFFNRMFL
DEVLOFL
DEVHIFL
PVLLFL
PVHIFL
PVHHFL
PVLOFL
OP
SPFORMAT
SPP
SP
FFBCINST
FFBCINVL
FFBCOPST
FFBCOPVL
BLKODIDX
CASIN
FFCSINST
FFCSINVL
CASIND
FFCSIDST
FFCSIDVL
OUT
IND
IN
OUTDST
OUTD
OUTST
PVFL
OFFNRMPR
SO
FFDVHILM

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

5 Fieldbus And TPS Parameter Cross-references

Table 2 FF/TPS Parameter Cross-Reference List , continued


FF Parameter
TPS Parameter
DV_HI_PRI
DV_HI_PRI
DV_LO_LIM
DV_LO_PRI
DV_LO_PRI
FF_GAIN
FF_SCALE.DecPt
FF_SCALE.EU0
FF_SCALE.EU100
FF_SCALE.UnitIndex
FF_VAL.Status
FF_VAL.Value
Function/Resource Block
GAIN
HI_HI_LIM
HI_HI_PRI
HI_HI_PRI
HI_LIM
HI_PRI
HI_PRI
IN.Status
IN.Value
LO_LIM
LO_LO_LIM
LO_LO_PRI
LO_LO_PRI
LO_PRI
LO_PRI
MIB: Network
MIB: Network
MIB: Network
MODE_BLK.Actual
MODE_BLK.Actual + MODE_BLK.Target
MODE_BLK.Normal
MODE_BLK.Permitted
MODE_BLK.Permitted
MODE_BLK.Target
NMIB:
NMIB:
None
None
None
None
None
None
None
None
None

R610
11/99

FFDVHIPR
DEVHIPR
FFDVLOLM
DEVLOPR
FFDVLOPR
FFFFGAIN
FFFFDECP
FFFFS0
FFFFS100
FFFFUIDX
FFFFVLST
FFFFVLVL
VWODIDX
FFGAIN
FFHHLM
FFHHPR
PVHHPR
FFHILM
FFHIPR
PVHIPR
FFINSTS
FFINVAL
FFLOLM
FFLLLM
PVLLPR
FFLLPR
PVLOPR
FFLOPR
SCHDVER
NUMSCHD
ACTSCHVR
FFMODEA
MODEBLKC
FFMODEN
MODEAPPL
FFMODEP
FFMODET
ACTVSCHD
PRILNKMS
$OPTOL
ALENBST
APPL
INITREQ
MODNUM
NODETYP
PNTSTATE
PTDESC
PTEXECST

HPM Parameter Reference Dictionary


Honeywell Inc.

443

5 Fieldbus And TPS Parameter Cross-references

Table 2 FF/TPS Parameter Cross-Reference List, continued


FF Parameter
TPS Parameter
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
OUT.Status
OUT.Value
OUT_1.Status
OUT_1.Value
OUT_2.Status
OUT_2.Value

444

$AUXUNIT
$SPTOL
ALMINFO
ALPRIOR
ASSOCCM
ASSOCDSP
BADPVPR
BLKDDID
CONTCUT
DEVSTAT
DISPTYPE
EUDESC
FBTYPE
HIGHAL
HIGHALPR
KEYWORD
MODATTR
MODEPERM
NAME
NMODATTR
NODENUM
NTWKNUM
PNTMODTY
PNTNODTY
PRIMMOD
PTINAL
PVCLAMP
PVEXEUHI
PVEXEULO
PVEXHIFL
PVEXLOFL
PVRAW
PVSOURCE
PVSRCOPT
PVTV
PVTVP
REDTAG
SLOTNUM
STATETXT
TBTYPE
UNIT
USEVFDNO
FFOUTSTS
FFOUTVAL
FFOUT1ST
FFOUT1VL
FFOUT2ST
FFOUT2VL

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

5 Fieldbus And TPS Parameter Cross-references

Table 2 FF/TPS Parameter Cross-Reference List, continued


FF Parameter
TPS Parameter
OUT_ACCUM.Status
OUT_ACCUM.Value
OUT_D.Status
OUT_D.Value
OUT_EXP.Status
OUT_EXP.Value
OUT_HI_LIM
OUT_LO_LIM
OUT_PTRIP.Status
OUT_PTRIP.Value
OUT_REM.Status
OUT_REM.Value
OUT_SCALE.DecPt
OUT_SCALE.EU0
OUT_SCALE.EU100
OUT_SCALE.UnitIndex
OUT_TRIP.Status
OUT_TRIP.Value
PID: OUT_SCALE.EU0
PID:
PV.Status
PV.Value
PV_SCALE.DecPt
PV_SCALE.EU0
PV_SCALE.EU100
PV_SCALE.UnitIndex
RATE
RCAS_IN
RCAS_IN.Status
RCAS_IN.Value
RCAS_IN_D
RCAS_IN_D.Status
RCAS_IN_D.Value
RCAS_OUT.Status
RCAS_OUT.Value
READBACK.Status
READBACK.Value
READBACK_D.Status
READBACK_D.Value
RESET
Resource block:
ROUT_IN
ROUT_IN.Status
ROUT_IN.Value
ROUT_OUT.Status
ROUT_OUT.Value
SEL_1
SEL_1.Status
SEL_1.Value
SEL_2

R610
11/99

FFOUTAST
FFOUTAVL
FFOUTDST
FFOUTDVL
FFOEXPST
FFOEXPVL
FFOPHILM
FFOPLOLM
FFPTRPST
FFPTRPVL
FFOREMST
FFOREMVL
FFOPDECP
FFOPS0
FFOPS100
FFOPUIDX
FFTRIPST
FFTRIPVL
CVEULO
CVEUHI
FFPVSTS
FFPVVAL
FFPVDECP
FFPVS0
FFPVS100
FFPVUIDX
FFRATE
RCASIN
FFRCINST
FFRCINVL
RCASIND
FFRCIDST
FFRCIDVL
FFRCOPST
FFRCOPVL
FFRBST
FFRBVL
FFRBDST
FFRBDVL
FFRESET
RSSTATE
ROUTIN
FFROINST
FFROINVL
FFROOPST
FFROOPVL
SEL1
FFSEL1ST
FFSEL1VL
SEL2

HPM Parameter Reference Dictionary


Honeywell Inc.

445

5 Fieldbus And TPS Parameter Cross-references

Table 2 FF/TPS Parameter Cross-Reference List, continued


FF Parameter
TPS Parameter
SEL_2.Status
SEL_2.Value
SEL_3
SEL_3.Status
SEL_3.Value
SP.Status
SP.Value
SP_HI_LIM
SP_LO_LIM
SP_RATE_DN
SP_RATE_UP
ST_REV
Starting OD index of
Transducer Block Header
Transducer Block Header
TRK_IN_D.Status
TRK_IN_D.Value
TRK_VAL.Status
TRK_VAL.Value
User configured
User configured
User configured
User configured
User configured
VFD model number
VFD Reference in
VFD revision number
VFD Tag in
VFD Vendor name
XD_SCALE.DecPt
XD_SCALE.EU0
XD_SCALE.EU100
XD_SCALE.UnitIndex

446

FFSEL2ST
FFSEL2VL
SEL3
FFSEL3ST
FFSEL3VL
FFSPSTS
FFSPVAL
FFSPHILM
FFSPLOLM
FFSPRTDN
FFSPRTUP
FFSTREV
TBODIDX
XVWODIDX
XBLKDDID
FFTRDIST
FFTRDIVL
FFTRVLST
FFTRVLVL
US8
US32
US16
FLOAT
VS
MODNAME
VFDREF
FFDEVREV
VFDTAG
VENNAME
FFXDDECP
FFXDS0
FFXDS100
FFXDUIDX

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FIELDBUS PARAMETERS INTRODUCTION

This section provides an introduction to the user-visible Fieldbus Foundation parameters that exist in the
TPS Builder.

6.1

PARAMETER DEFINITION FORMAT

In Section 8 of this publication, the parameter definitions are listed in alphabetical order
according to the parameter name, which often exceeds eight characters in length. Parameters in
this publication are defined using the general format shown below in the sample Alarm_Hys
parameter.

Alarm_Hys
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Static
4
Fieldbus Device
0-50 %

Description:
Determines the amount that the PV must return within the alarm limits before
the alarm condition clears. Alarm hysteresis expressed as a percent of the span
of the PV.

HPM Parameter Reference Dictionary


Honeywell Inc.

447

6 Fieldbus Parameters Introduction

FF Data Type

This entry is the data type/structure type that defines how the parameter is viewed by the system.
Table 3 lists data types and structure types are used for the parameters defined in Section 8.
Table 3 Data Types and Structure Types
FF Object
Data Type
Dictionary Index
Logical (Boolean)
Integer8
Integer16
Integer32
Unsigned8
Unsigned16
Unsigned32
Float
Visible String
Octet String
Date
Time Of Day
Time Difference
Bit String
Time Value

1
2
3
4
5
6
7
8
9
10
11
12
13
14
21

Structure Type

FF Object
Dictionary Index

Block Header
Value & Status - Floating
Point
Value & Status - Discrete
Value & Status - Bitstring
Scaling
Mode
Access Permissions
Alarm Float
Alarm Discrete
Event Update
Alarm Summary
Alert Analog
Alert Discrete
Alert Update
Trend Float
Trend Discrete
Trend Bit String
FB Link
Simulate - Floating Point
Simulate - Discrete
Simulate - Bitstring
Test
Action
VFD Reference Entry
FB Start Entry
VCR Static Entry
DLME Link Master
Information
PLME Basic Information
DLME Link Settings

64
65

448

66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
90
91
97
104
109
111

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

6 Fieldbus Parameters Introduction

Length
Number of octets in the value.
Usage
Determines how the parameter is used, as follows :
Contained Contained parameters may be used to provide values to block algorithms.
Their initial values may be set by the fieldbus-device manufacturer or as part of
configuration, and they may be adjusted during operation. Also, they may be used to reflect
the results of block execution. Linking of input or output parameters to contained parameters
is not allowed. The first six parameters of any block are always contained parameters.
Input Input parameters may be defined for function blocks to allow their values to be
obtained through function block links to other input or output parameters. They are
structured parameters composed of a value and a status. The data type specified for input
parameters is dependent on the data type of its value field. The status field, however, is
defined to be identical for all input parameters.
Output Output parameters may be defined in function blocks for use by other function
blocks through function block links. They are structured parameters that are composed of a
value and a status. The data type specified for output parameters is dependent on the data
type of its value field. The status field, however, is defined to be identical for all output
parameters (and input or contained parameters having the status field).
Storage
This defines the data storage class of the parameter, as follows:
Dynamic
Mixed
Non-Volatile
Static

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

449

6 Fieldbus Parameters Introduction

Valid View(s)
Fieldbus Views are defined as being View 1 through View 4, and they are defined as follows:

1 = View 1 (Operation Dynamic) Information required by a plant operator to view process


control, see alarm conditions, and adjust operating targets.
2 = View 2 (Operation Static) Static information which may be required for display to an
operator with dynamic information. This information will only be read once when the
associated display is first called up, and refreshed when and if the static update code changes.
3 = View 3 (All Dynamic) Information which is changing in value and may need to be
referenced by a detail display which shows everything.
4 = View 4 (Other Static) Information that is normally referenced only during
configuration or maintenance, and that has a specific value unless changed by an operator or
instrument technician.
4b = Second View 4
4c = Third View 4

Classification
This entry determines where the parameter class, as follows:

Fieldbus Device

TPSB Only (TPS Builder Only)

CFF File

Range
This defines the range of the value that can be entered. If the range of values is an enumeration,
you may have to refer to Appendix A for additional information.

450

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

6 Fieldbus Parameters Introduction

6.2

FIELDBUS STRUCTURED DATA TYPES

This section presents the Simple Variable data types defined by the Fieldbus Foundation.
6.2.1 VALUE & STATUS - FLOATING POINT STRUCTURE
This data structure consists of the value and status of floating point parameters that are Inputs or
Outputs.
Data Type: ....... Value & Status - Floating Point
Attribute: .......... Number of Elements = 2
Attribute: .......... List of Elements
Element
1
2

Element
Name
Status
Value

Data Type
(Index)
Unsigned8 - (5)
Float - (8)

Size
1
4

6.2.2 VALUE & STATUS - DISCRETE STRUCTURE


This data structure consists of the value and status of discrete value parameters.
Data Type: ....... Value & Status - Discrete
Attribute: .......... Number of Elements = 2
Attribute: .......... List of Elements (shown below)
Element
1
2

Element Name
Status
Value

Data Type (Index)


Unsigned8 - (5)
Float - (8) (5)

Size
1
1

6.2.3 SCALING STRUCTURE


This data structure consists of the static data used to scale floating point values for display
purposes.
Data Type: ....... Scaling
Attribute: .......... Number of Elements = 4
Attribute: .......... List of Elements (shown below)
Element
1
2
3
4

R610
11/99

Element Name
EU at 100%
EU at 0%
Units Index

Data Type (Index)


Float - (8)
Float - (8)
Unsigned16 - (6)

Decimal Point

Integer8 - (2)

Size
4
4
2
1

HPM Parameter Reference Dictionary


Honeywell Inc.

451

6 Fieldbus Parameters Introduction

6.2.4 MODE STRUCTURE


This data structure consists of bit strings for target, actual, permitted, and normal modes.
Data Type:
Mode
Attribute: .......... Number of Elements = 4
Attribute: .......... List of Elements (shown below)
Element
1
2
3
4

Element Name
Target
Actual
Permitted
Normal

Data Type (Index)


Bitstring- (14)
Bitstring - (14)
Bitstring - (14)
Bitstring - (14)

Size
1
1
1
1

6.2.5 ACCESS PERMISSIONS


This data structure consists of access control flags for access to block parameters.
Data Type: ....... Access Permissions
Attribute: .......... Number of Elements = 2
Attribute: .......... List of Elements (shown below)
Element
1
2

Element Name
Grant
Deny

Data Type (Index)


Bit String - (14)
Bit String - (14)

Size
1
1

6.2.6 ALARM FLOAT STRUCTURE


This data structure consists of data that describes floating point alarms.
Data Type: ....... Alarm Float
Attribute: .......... Number of Elements = 5
Attribute: .......... List of Elements (shown below)
Element
1
2
3
4
5

Element Name
Unacknowledged
Alarm State
Time Stamp
Normal
Subcode

Data Type (Index)


Unsigned8 - (5)
Unsigned8 - (5)
Time Value - (21)
Unsigned16 - (6)
Unsigned16 - (6)

Size
1
1
8
2
4

6.2.7 EVENT UPDATE STRUCTURE


This data structure consists of data that describes a static revision alarm.
Data Type: ....... Event Update
Attribute: .......... Number of Elements = 5
Attribute: .......... List of Elements (shown below)
Element
1
2
3
4
5

452

Element Name
Unacknowledged
Update State
Time Stamp
Static Revision
Relative Index

Data Type (Index)


Unsigned8 - (5)
Unsigned8 - (5)
Time Value - (21)
Unsigned16 - (6)
Unsigned16 - (6)

Size
1
1
8
2
2

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

6 Fieldbus Parameters Introduction

6.2.8 ALARM SUMMARY STRUCTURE


This data structure consists of data that summarizes 16 alerts.
Data Type: ....... Alarm Summary
Key Attribute: ... Index = 74
Attribute: .......... Number of Elements = 4
Attribute: .......... List of Elements (shown below
Element
1
2
3
4

Element Name
Current
Unacknowledged
Unreported
Disabled

Data Type (Index)


Bit String - (14)
Bit String - (14)
Bit String - (14)
Bit String - (14)

Size
2
2
2
2

6.2.9 FB LINK STRUCTURE


This data structure consists of function block link data.
Data Type: ....... FB Link
Attribute: .......... Number of Elements = 5
Attribute: .......... List of Elements (shown below)
Element
1
2
3
4
5

Element Name
Local Index
VCR Number
Sample Type
Service Operation
Stale Count Limit

Data Type (Index)


Unsigned16 - (6)
Unsigned16 - (6)
Unsigned8 - (5)
Unsigned8 - (5)
Unsigned8 - (5)

Size
2
2
2
1
1

6.2.10 TEST STRUCTURE


This data structure consists of function block test read/write data.
Data Type: ....... Test
Attribute: .......... Number of Elements = 15
Attribute: .......... List of Elements (shown below)

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

453

6 Fieldbus Parameters Introduction

Element

Element Name

Data Type (Index)

1
2
3
4
5
6
7
8
9
10
11
12
13

Value 1
Value 2
Value 3
Value 4
Value 5
Value 6
Value 7
Value 8
Value 9
Value 10
Value 11
Value 12
Value 13

14
15

Value 14
Value 15

Boolean - (1)
Integer8 - (2)
Integer16 - (3)
Integer32 - (4)
Unsigned8 - (5)
Unsigned16 - (6)
Unsigned32 - (7)
Floating Point - (8)
VisibleString - (9)
Octet String - (10)
Date - (11)
Time of Day - (12)
Time Difference (13)
Bitstring - (14)
Time Value- (21)

Size
1
1
2
4
1
2
4
4
32
32
7
6
6
2
8

6.2.11 VFD PREFERENCE ENTRY STRUCTURE


The VFD_REF_ENTRY data type structure is used to represent an entry in the virtual field
device reference list.
Numeric Identifier:
90
Number of Elements: 2
List of Elements:
Data Type Index:
Length:
Data Type Index:
Length:

7 (Unsigned32)
4
9 (Visible String)
32

6.2.12 FB START ENTRY STRUCTURE


The FB_START_ENTRY data type structure is used to represent an entry in the function block
starting schedule. The START_TIME_OFFSET element is in the units of time maintained by
the data link layer, with each count representing 1/32 of a millisecond. A value of
FFFFFFFF(hex) for this element indicates an unused entry.
Numeric Identifier:
91
Number of Elements: 3
List of Elements:
Data Type Index:
Length:
Data Type Index:
Length:
Data Type Index:
Length:

454

7 (Unsigned32)
4
6 (Unsigned16)
2
7 (Unsigned32)
4

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SUPPORTED FUNCTION AND TRANSDUCER BLOCKS/NETWORK


MANAGEMENT AND SYSTEM MANAGEMENT PARAMETERS

7.1 PARAMETERS PER SUPPORTED FUNCTION BLOCK (AI, PID, AO)


7.1.1 ANALOG INPUT FUNCTION BLOCK PARAMETERS
ACK_OPTION
ALARM_HYS
ALARM_SUM
ALERT_KEY
BLOCK_ALM
BLOCK_ERR
CHANNEL
FIELD_VAL
GRANT_DENY
HI_ALM
HI_HI_ALM
HI_HI_LIM

HI_HI_PRI
HI_LIM
HI_PRI
IO_OPTS
L_TYPE
LO_ALM
LO_LIM
LO_LO_ALM
LO_LO_LIM
LO_LO_PRI
LO_PRI
LOW_CUT

MODE_BLK
OUT
OUT_SCALE
PV
PV_FTIME
SIMULATE
ST_REV
STATUS_OPTS
STRATEGY
TAG_DESC
UPDATE_EVT
XD_SCALE

7.1.2 PID FUNCTION BLOCK PARAMETERS


ACK_OPTION
ALARM_HYS
ALARM_SUM
ALERT_KEY
BAL_TIME
BKCAL_HYS
BKCAL_IN
BKCAL_OUT
BLOCK_ALM
BLOCK_ERR
BYPASS
CAS_IN
CONTROL_OPTS
DV_HI_ALM
DV_HI_LIM
DV_HI_PRI
DV_LO_ALM
DV_LO_LIM
DV_LO_PRI
FF_GAIN
FF_SCALE
FF_VAL

GAIN
GRANT_DENY
HI_ALM
HI_HI_ALM
HI_HI_LIM
HI_HI_PRI
HI_LIM
HI_PRI
IN
LO_ALM
LO_LIM
LO_LO_ALM
LO_LO_LIM
LO_LO_PRI
LO_PRI
MODE_BLK
OUT
OUT_HI_LIM
OUT_LO_LIM
OUT_SCALE
PV
PV_FTIME

PV_SCALE
RATE
RCAS_IN
RCAS_OUT
RESET
ROUT_IN
ROUT_OUT
SHED_OPT
SP
SP_HI_LIM
SP_LO_LIM
SP_RATE_DN
SP_RATE_UP
ST_REV
STATUS_OPTS
STRATEGY
TAG_DESC
TRK_IN_D
TRK_SCALE
TRK_VAL
UPDATE_EVT

7.1.3 ANALOG OUTPUT FUNCTION BLOCK PARAMETERS


ALERT_KEY
BKCAL_OUT
BLOCK_ALM
BLOCK_ERR
CAS_IN
CHANNEL
FSTATE_TIME
FSTATE_VAL
GRANT_DENY
IO_OPTS

R610
11/99

MODE_BLK
OUT
PV
PV_SCALE
RCAS_IN
RCAS_OUT
READBACK
SHED_OPT
SIMULATE
SP

SP_HI_LIM
SP_LO_LIM
SP_RATE_DN
SP_RATE_UP
ST_REV
STATUS_OPTS
STRATEGY
TAG_DESC
UPDATE_EVT
XD_SCALE

HPM Parameter Reference Dictionary


Honeywell Inc.

455

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.2 PARAMETERS PER SUPPORTED TRANSDUCER BLOCK PARAMETER


Transducer Block Name

Standard Pressure with Calibration Basic Access

Standard Temperature with Calibration Basic Device Access

Standard Radar Level with Calibration Basic Device Access

Standard Flow with Calibration Basic Device Access

Standard Basic Positioner Valve Basic Device Access

Standard Advanced Positioner Valve Basic Device Access

Standard Discrete Positioner Valve Basic Device Access

The following are some examples:


7.2.1 STANDARD ADVANCED POSITIONER VALVE BASIC DEVICE EXAMPLE
ACT_FAIL_ACTION
ACT_MAN_ID
ACT_MODEL_NUM
ACT_SN
ALER_KEY
BLOCK_ALM
BLOCK_ERR
COLLECTION_DIRECTORY
FINAL_POSITION_VALUE
FINAL_VALUE
FINAL_VALUE_CUTOFF_HI

FINAL_VALUE_CUTOFF_LO
FINAL_VALUE_RANGE
MODE_BLK
SERVO_GAIN
SERVO_RATE
SERVO_RESET
ST_REV
STRATEGY
TAG_DESC
TRANSDUCER_DIRECTORY
TRANSDUCER_TYPE

UPDATE_EVT
VALUE__SN
VALUE_MAN _ID
VALUE_MODEL_NUM
VALUE_TYPE
XD_CAL_DATE
XD_CAL_LOC
XD_CAL_WHO
XD_ERROR

7.2.2 STANDARD TEMPERATURE WITH CALIBRATION BASIC DEVICE ACCESS


ALERT_KEY
BLICK_ERR
BLOCK_ALM
CAL_MIN_SPAN
CAL_POINT_HI
CAL_POINT_LO
CAL_UNIT
COLLECTION_DIRECTORY
MODE_BLK
MODULE_SN

456

PRIMARY_VALUE
PRIMARY_VALUE_RANGE
PRIMARY_VALUE_TYPE
SECONDARY_VALUE
SECONDARY_VALUE_UNIT
SENSOR_CAL_DATE
SENSOR_CAL_LOC
SENSOR_CAL_METHOD
SENSOR_CAL_WHO
SENSOR_CONNECTION

HPM Parameter Reference Dictionary


Honeywell Inc.

SENSOR_RANGE
SENSOR_SN
SENSOR_TYPE
ST_REV
STRATEGY
TAG_DESC
TRANSDUCER_DIRECTORY
TRANSDUCER_TYPE
UPDATE_EVT
XD_ERROR

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.2.3 STANDARD PRESSURE WITH CALIBRATION BASIC DEVICE ACCESS


ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
BLOCK_ERR
UPDATE_EVT
BLOCK_ALM
TRANSDUCER_DIRECTORY
TRANSDUCER_TYPE

R610
11/99

XD_ERROR
COLLECTION_DIRECTORY
PRIMARY_VALUE_TYPE
PRIMARY_VALUE
PRIMARY_VALUE_RANGE
CAL_POINT_HI
CAL_POINT_LO
CAL_MIN_SPAN
CAL_UNIT
SENSOR_TYPE

HPM Parameter Reference Dictionary


Honeywell Inc.

SENSOR_RANGE
SENSOR_SN
SENSOR_CAL_METHOD
SENSOR_CAL_LOC
SENSOR_CAL_DATE
SENSOR_CAL_WHO
SENSOR_ISOLATOR_MTL
SENSOR_FILL_FLUID
SEOCNDARY_VALUE
SECONDARY_VALUE_UNIT

457

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.3

SCHEDULE PARAMETERS

Table 4 Link Active Schedule (LAS) Parameters


Octet
Index

Schedule Summary
Parameters

1
2

ScheduleHeader
ScheduleSummary

3-4

ScheduleVersionNumber

5-6

ScheduleBuilderIdentifier

NumberOfSubSchedules

MaximumSchedulingOverhead

9-10

StorageRequiredForTotalSchedule

11-12

ScheduleJitterCommitment

13-14

V_MRD_V_ST

15-16

V_TSL

17-22

T0

23-26

MacrocycleDuration

27-28

SubScheduleRecordReference(64)

Octet
Index

This is the schedule header and is encoded as 0xFF


This attribute identifies the type of schedule transfer SPDU
0x00 to 0x07. Default is a 0x01.
The schedule version number. If this field is zero it represents a
null schedule.
The valid range for this variable is 0x0100 to 0x0FFF. This is the
source of the schedule and is not used by LAS.
This attribute specifies the number of sub-schedules in the
schedule.
This attribute specifies the maximum scheduling overhead, V
(MSO), that was used in constructing the schedule. The range is
0x00 to 0x3F. The default value is 0x3F. The unit of this variable
is the transmission duration of one octet. This overhead is
included in the time allocated for each scheduled activity, and is
only used during schedule construction for determination of
whether a DLE can serve as LAS for an existing schedule.
This attribute specifies the total storage space for the schedule
summary and all of the sub-schedules in octets (bytes).
This attribute specifies the minimum resolution of the time clock
required to execute this schedule and still meet the jitter
specifications to which the schedule was constructed. The units
are 1/32 of a millisecond.
This attribute is the value of the maximum response delay slot
time multiplied by the octet duration, which was used in the
construction of the schedule.
This attribute is the link id of the source of time distribution,
which was used to specify the DL time used in this schedule.
This attribute is the DL time base as referenced from the DL time
publisher. Not used by LAS
This attribute specifies the duration of the link macrocycle. The
duration is equal to the least common multiple of periods of all
sub-schedules. The clock tick unit is 1/32 of a millisecond.
This attribute specifies the sub-schedule identifier. The identifier
st
must not be zero or equal subsequence identifiers. The 1 zero
identifier in this array terminates the Schedule Summary

Sub Schedule Parameters

1
2

SubScheduleHeader
SubSchedule

3-4

SubScheduleVersionNumber

5-6

SubScheduleIdentifier

7-10

SubSchedulePeriod

11-253

Sequences 1-n

458

Description

Description
This is the sub schedule header and is encoded as 0xFF
This attribute specifies the type of schedule transfer, subschedule. The encoding is 0x08 to 0x0F where the value of 0x09
to 0x0F represents the version number of the schedule transfer
encoding.
This is the version number of the schedule that is identical to the
ScheduleVersionNumber in the Schedule Summary.
This attribute, if non-zero, is the sub-schedule identifier as
referenced in the Schedule Summary. If zero, this is the last
octet of this SPDU and is used as an end marker for subschedules.
This attribute specifies the non-zero execution period of all
sequences in the sub-schedule. The clock tick unit is 1/32 of a
millisecond.
Octets 11 to <253 specify one or more sequences as described
in the table below. The end of a sub-schedule is indicated by 4
consecutive octets whose value is zero

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

Table 4 Link Active Schedule (LAS) Parameters (continued)


Octet
Sequence Parameters
Index

Description

1-4

ScheduleStartingTimeOffset

This attribute is used to specify a non-zero starting time offset


form the T0 attribute specified in the Schedule Summary. The
clock tic units are 1/32 of a millisecond. Since T0 is not used by
FF the calculation is as follows: DL-Time V (DLT0) = V (LST0)
+ C (NT) = N * (macrocycle-duration) + M * (sub-schedule
period) + Schedule-Starting-time offset where, N and M are nonnegative integers.

5-6

MaxComputedDurationOfSequence

7-n

Publisher Elements 1-n

This attribute is for reference and is not used by LAS. This


specifies the worst case duration of the sequence in 1/32 of a
millisecond ticks.
Octets 7 n specify 1 or more elements as specified in the table
below. The end of sequence marker is two octets whose value is
zero.

Octet
Index

Publisher Elements

ElementType

2-3

ElementVariable

R610
11/99

Description
This attribute specifies the type of transaction. For now, the TPS
Builder only provides elements for CD_Request (compel data).
The encoding of the bits shall be a CD-request short DLCEP
(1011 00PP). The PP is a priority code where: 01 = urgent, 10 =
normal, and 11 = time available.
This attribute is the short DLCEP-address. The first octet is the
node address (14-F7), the second octet is a selector (20-F7) that
indicates the published parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

459

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.4

NETWORK MANAGEMENT PARAMETERS

7.4.1 NETWORK MANAGEMENT DIRECTORY ENTRY


The directory entry (Table 5) values provide information about the number of Network
Management objects, and the address of the objects in the device. This directory is supplied by
the manufacturer and is not changeable by a user.
Table 5 Network Management Directory Entry
Directory Entry

Description

DirectoryRevisionNumber
NumberOfDirectoryObjects

This entry identifies the revision level of the NMA Directory Object.
This entry identifies the total number of directory objects in the NMA.
The directory objects are consecutively numbered in the Object
Dictionary beginning with S-OD index +1.
This entry identifies the total number of references, excluding the
directory header, in a single directory. Each reference is composed of
st
two unsigned16 array entries. The 1 reference is the Stack
Management reference.
st
This directory entry is the directory entry number of the 1 composite
list reference. Composite list references contain a directory offset and
not an OD Index. The List of MNE composites below is a composite
reference.
The number of composite list referenced by this directory.
The OD Index for the Stack management entity for the NMA.
The number of objects in the Stack management composite. Usually
1.
The starting OD Index for the composite for the list of Virtual
Communication Relationships accessible through the NMA.
st
The Number of VCR objects. The 1 object is the
nd
VCRListControlVariable. The 2 object is the
rd
VCRListCharacteristicRecord. The 3 object through MaxEntries is
the list of VCRStaticEntry objects. The list of VCRDynamicRecords
follows the static VCRs. If implemented, a list of VCRStatistic records
follow the dynamic VCRs.
The OD Index for the composite representing the BASIC classes of
devices that are accessible through the NMA.
st
The number of basic Data Link Management Entity Objects. The 1
object is the DlmeBasicCharacteristicRecord.
The OD Index for the composite representing LINK MASTER class
device accessible through the NMA. If the device is a BASIC device
this entry is set to zero.
st
The number of objects in the DlmeLinkMaster composite. The 1
object is the DlmeLinkMaster Capabilities Variable. This entry is zero
for a BASIC device.
The OD Index for the composite representing the objects for a
DlmeLinkSchedule class accessible through the NMA. If the device
is a BASIC device this entry is set to zero.
The number of objects in the DlmeLinkScheduleList. If the device is a
st
BASIC device this entry is set to zero. The 1 object is the Link
nd
Schedule Activation Variable. The 2 object is the Link Schedule
rd
Characteristic Record. The 3 set of object is the
th
ListOfScheduleDescriptorRecords and the 4 set of objects is the
ListOfScheduleDomains. Assume the starting OD Index for the
DlmeLinkSchedule is 100 and there is one schedule domain. The OD
Index for that domain is 103. If two schedule domains the OD Index
st
nd
for the 1 domain would be 104 and the 2 would be 105.

TotalNumberOfDirectoryEntries

DirectoryIndexOfFirstCompositeListReference

NumberOfCompositeListReferences
StackMgtOdIndex
NumberOfObjectsInStackManagement
VcrListOdIndex
NumberOfObjectsInVcrList

DlmeBasicOdIndex
NumberOfObjectsInDllBasic
DlmeLinkMasterOdIndex

NumberOfObjectsInDllLme

LinkScheduleListOdIndex

NumberOfObjectsInDllLinkSchedule

460

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

Table 5 Network Management Directory Entry (continued)


Directory Entry

Description

DlmeBridgeOdIndex

This OD Index represents the composite for a BRIDGE device. If the


data link layer is not a BRIDGE class device, this entry is set to zero.
The number of the object in the DlmeBridge composite.
This OD Index entry represents the address for the composite
representing the PlmeBasic object(s) (Physical layer basic
description).
Number of objects in the PlmeBasic composite.
This entry is a reference to the Media Management composite
objects (MmeWireODIndex, NumberO MmeWire objects), that are
accessible through the NMA.
This entry represents the number of consecutive MME Composite
reference in the list of MME references.
This represents the OD Index for the MmeWireOdIndex
This represents the number of MnewireObjects.

NumberOfObjectsInDllBridge
PlmeBasicOdIndex

NumberOfObjectsInPhyLme
ListOfMmeReferences

NumberOfMmeComposites
FirstMmeComposite
NumberOfObjectsInMme

Table 6 Network Management Parameters


Network Management
Parameters
DlmeLinkMasterInfo

DlmeLinkSettings
DlOperateFunctionalClass
MaxTokenHoldTimeArray
PlmeBasicInfo
VcrStaticEntry

R610
11/99

Parameter Description
Data Link Mgmt. Entity Link Master Information.
Refer to DlmeLinkMasterInfo (Table 11).
This attribute is also defined in the IEC/ISA DL Specification Part 4 9.4.1.3 (e.5.i).
Data Link Mgmt. Entity Link Settings
Refer to DlmeLinkSettings (Table 4).
Dl Operate Functional Class.
Refer to DlmeLinkMasterInfo (Table 11).
Physical Layer ME Basic Info
Refer to PlmeBasicInfo (Table 12).
Virtual Communication Resource List
Refer to VcrStaticEntry (Table 9).

HPM Parameter Reference Dictionary


Honeywell Inc.

461

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.4.3 DLMELINKSETTINGS
Table 7 lists and describes the attributes for DlmeLinkSettings (Class) of Root (subclass).
Table 7 DlmeLinkSettings
Name
SlotTime
PerDlpduPhlOverhead
MaxResponseDelay

FirstUnpolledNodeId
ThisLink

MinInterPduDelay

NumConsecUnpolledNodeId

PreambleExtension
PostTransGapExtension
MaxInterChanSignalSkew
Attribute: TimeSyncClass

Description
Defined in the IEC/ISA DL Specification Part 4 chapter
5.7.1.1.
Defined in the IEC/ISA DL Specification Part 4 chapter
5.7.1.2.
Defined in the IEC/ISA DL Specification Part 4 chapter
5.7.1.3. Attributes SlotTime and MaxResponseDelay
should be set in such a way that the product represents the
maximum response delay in octets of the device.
Defined in the IEC/ISA DL Specification Part 4, clause
5.7.5.15.
ThisLink V(TL)
Defined in the IEC/ISA DL Specification Part 4 chapter
5.7.1.9. It is the address of the link that the device is
currently connected to.
MinInterPduDelay V(MD)
Defined in the IEC/ISA DL Specification Part 4 chapter
5.7.1.12. It is the minimum inter PDU delay the device
requires to operate correctly.
NumConsecUnpolledNodeId V(NUM)
Defined in the IEC/ISA DL Specification Part 4, clause
5.7.5.16.
Defined in ISA/IEC Part 2 Chapter 6.2. It is an Unsigned8
variable whose allowable values are between 0 and 7.
Defined in ISA/IEC Part 2 Chapter 6.2. It is an Unsigned8
variable whose allowable values are between 0 and 7.
Defined in ISA/IEC Part 2 Chapter 6.2. It is an Unsigned8
variable whose allowable values are between 0 and 7.
Defined in IEC/ISA DL Specification Part 4 chapter
5.7.1.25. It represents the TimeSyncClass for the link.

7.4.4 MAXTOKENHOLDTIMEARRAY
Table 8 describes the attributes for MaxTokenHoldTimeArray (class) of Root (subclass).
Table 8 MaxTokenHoldTimeArray
Name
SlotTime

462

Description
This attribute is an array of 8 octet string elements. Each
element in the array is 64 octets long. Each 64 octet array
element contains 32 values. Each value consists of 2
octets that indicates the initial amount of local link capacity
for each active node in the LiveListStatusArrayVariable.
The order of values corresponds to the order of nodes in
the LiveListStatusArrayVariable. These values are defined
in the IEC/ISA DL Specification Part 4 chapter 5.7.5.10.
This attribute is represented in FMS as defined in the
IEC/ISA DL Specification Part 4 chapter 5.7.1.1.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.4.5 VCRSTATICENTRY
Table 9 describes the attributes for VcrStaticEntry (Class) . The TPS Builder automatically
builds these entries during building of the Link Active Schedule. The table below depicts the
binary values that are loaded into the devices.
Table 9 VcrStaticEntry
Name
FasArTypeAndRole

Description
The semantics of the elements contained in this attribute are defined in
the Fieldbus Foundation FAS specification. It is an octet string of length
1, defined as follows:
B8

B7
B6 B5
(FAS Role)

NotConfig:
Peer Initiator:
Peer Responder:
Client:
Server:
Source:
Sink:
Publisher:
Subscriber

0000 = 0
1001 = 9
0001 = 1
1010 = 10
0011 = 3
0100 = 4
0101 = 5
0110 = 6
0111 = 7

B4 B3 B2
(FAS AR Type)

B1 (lsb)
(FMS Bypass)

NotConfig: 000 = 0
QUB: 001 = 1
QUU: 010 = 2
BNU: 011 = 3

FALSE 0
TRUE: 1
When FMS Bypass is TRUE: 1TRUE,
FMS is bypassed (the user application
interacts directly with FAS).

FasArTypeAndRole Coding

FasDllLocalAddr

FasDllConfiguredRemoteA
ddr

FasDllSDAP

FasDllMaxConfirmDelayOn
Connect

R610
11/99

The FAS specification defines the valid combinations of AR Type and


Role attributes. The definition of the stack, as defined in the
StackManagement attribute FasArTypesAndRolesSupported further
restricts the values that may be assigned to this attribute. A value of
0x00 indicates that this VCR is unconfigured.
It is defined in the DLL mapping portion of the FAS specification. It
specifies a DLCEP-Address or a DL(SAP)-Address (individual or
group). If it is not a group address, then only the selector is defined.
The structure of DL-Addresses is defined in the Data Link Layer
Protocol Specification, Annex A.
NOTE: A value of zero indicates that the relationship is Free in FAS
terminology.
This element is defined in the DLL mapping portion of the FAS
specification. Depending on the FAS AR Type, it corresponds to either
the FAS QUB Remote DLCEP-Address or to the FAS QUU Remote
DL(SAP)-Address (individual or group). It is not used for Publisher
AREPs. Its value is set to zero to indicate that the FAS
RemoteAddressConfigurationType is FREE (for QUU and QUB
AREPs). The structure of DL-Addresses is defined in the Data Link
Layer Protocol Specification, Annex A.
NOTE: A value of zero for QUU and QUB AREPs indicates the
relationship endpoint is Free in FAS terminology.
The individual fields of this element are defined in the DLL mapping
portion of the FAS specification. This attribute is an octet string of
length 1 defined as follows:
B8
LAS
Scheduled

B7 B6 B5
B4 B3
B2 B1 (lsb)
DLCEP Data
DLPDU Authentication Priority
Delivery Features

FALSE 0
TRUE 1

Unordered 000
Ordered 001
Disordered 010
Classical 011

Ordinary 00
Source 10
Maximal 11

TimeAvailable 11
Normal 10
Urgent 01

It is defined in the DLL mapping portion of the FAS specification as the


MaxConfirmDelayOnDlConnect for QUB and BNU AREPs. It is not
used for QUU AREPs. It is the maximum amount of time to be used to
complete the DL Connection establishment process.

HPM Parameter Reference Dictionary


Honeywell Inc.

463

Supported Function and Transducer Blocks/Network management and System Management Parameters

Table 9 VcrStaticEntry (continued)


Name
FasDllMaxConfirmDelay
OnData

FasDllMaxDlsduSize

FasDllResidualActivitySu
pported

FasDllTimelinessClass

Description

It defined in the DLL mapping portion of the FAS specification as the


MaxConfirmDelayOnDlData for QUB AREPs and as the
MaxConfirmDelayOnUnitData for QUU AREPs. It defines the maximum
amount of time that the data link layer has to complete individual
connectionless and connection-oriented data transfers.
It is defined in the DLL mapping portion of the FAS specification as the
MaxDlsduSizeFromRequester/MaxDlsduSizeFromResponder for QUB
and BNU AREPs and as the MaxDlsduSize for QUU AREPs. It is the
maximum permitted Data Link Service Data Unit (DLSDU) size that can
be sent on this VCR.
It is defined in the DLL mapping portion of the FAS specification. It is
used for QUB VCRs only, providing the value for both the
ResidualActivityAsSender and ResidualActivityAsReceiver QUB AREP
attributes. When TRUE, this Flag indicates that residual activity
monitoring will be performed by the DLL in each direction of transfer.
The FasDllMaxConfirmDelayOnConnect indicates the inactivity time-out
interval.
It is composed of publisher and subscriber timeliness classes (defined
in the DLL mapping portion of the FAS specification) and the
subscribers Duplicate PDU Detection Supported flag (defined in the
BNU AREP attribute in the FAS specification). It is used for BNU VCRs
only. It is a OctetString of length 1 octet defined as follows:
B8
Reserved

B7 B6 B5
Publisher DL
Timeliness
Class
None: 000
Residence 001
Update 010
Synchronous 011
Transparent 100

FasDllPublisherTimeWin
dowSize
FasDllPublisherSynchron
izingDlcep

FasDllSubscriberTimeWi
ndowSize

FasDllSubscriberSynchro
nizingDlcep

FmsVfdId

464

B4
Duplicate PDU
Detection
Support
FALSE 0
TRUE 1

B3 B2 B1 (lsb)
Detection Supported
Subscriber DL
Timeliness Class
(present for subscriber
VCR only)
None: 000
Residence 001
Update 010
Synchronous 011
Transparent 100

It is defined in the DLL mapping portion of the FAS specification as the


PublisherTimeWindowSize. It is used for BNU VCRs only and then only
if the PublisherTimelinessClass of this record is not None.
It is defined in the DLL mapping portion of the FAS specification. It is
used for BNU VCRs only and then only if the PublisherTimelinessClass
(for Publisher AREPs) is Update or Synchronous. This attribute is the
DL-address of the DLCEP that is to be used for synchronization within
the DLL.
It is defined in the DLL mapping portion of the FAS specification as the
SubscriberTimeWindowSize. It is used for Subscriber BNU VCRs only
and then only if the SubscriberTimelinessClass of this record is not
None.
It is defined in the DLL mapping portion of the FAS specification as the
SubscriberSynchronizingDlcep. It is used for BNU VCRs only and then
only if the SubscriberTimelinessClass (for Subscriber AREPs) is Update
or Synchronous. This attribute is the DL-address of the DLCEP that is
to be used for synchronization within the DLL.
It is defined in the FMS specification as the FMS VFD ID Static VCR
Information attribute. It references the VFD associated with this VCR.
This value is unambiguous within the scope of the physical device, and
must be one of the values contained in the SMIB List of VFD Reference
Entry Objects. This attribute is used for QUB Server, QUB Peer, QUU
Source and BNU Publisher VCRs. Definition and handling of FMS
VFDs are described in the FOUNDATION Fieldbus Specification
System Architecture.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

Table 9 VcrStaticEntry (continued)


Name
FmsMaxOutstandingServ
icesCalling

FmsMaxOutstandingServ
icesCalled

FmsFeaturesSupported

R610
11/99

Description

It is defined in the FMS Specification as the


MaxOutstandingServicesCalling Static VCR Information attribute. It is
used only for QUB VCRs.
NOTE: This value may be used by an implementation in the
determination of DL max queue depth.
It is defined in the FMS Specification
MaxOutstandingServicesCalledStatic VCR Information attribute. It is
used only for QUB VCRs.
NOTE: This value may be used by an implementation in the
determination of DL max queue depth.
It is defined in the FMS Specification as the FmsFeaturesSupported
Static VCR Information attribute. It indicates the services that are
supported by FMS for the VCR. It is a BitString of length 8 octets. Each
VCR may be defined to support all or a subset of the services specified
by this element. The format of this element is defined in Section 3.3.2 of
the FMS Specification. This element is not used when FMS is bypassed
(see FasArTypeAndRole).

HPM Parameter Reference Dictionary


Honeywell Inc.

465

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.4.6 DLMELINKMASTERINFO
Table 10 lists and describes the attributes for DlmeLinkMasterInfo (Class)

Table 10 DlmeLinkMasterInfo
Name
DlmeLinkMasterOdIndex
DlmeLinkMasterCapabilitiesVariable

Description
This attribute specifies the first OD index in the Dlme Link Master composite
object, which is the DlmeLinkMasterCapabilitiesVariable.
This element specifies the capabilities supported by the Link Master. It is
represented in FMS as:
FMS Object Name: DlmeLinkMasterCapabilitiesVariable
Object Type:
Simple Variable
Data Type:
Octet string
Length:
1
FMS Access Right: RaWa
The table below illustrates the structure of this variable. A bit value of 1
indicates that the corresponding attribute is present in the NMIB. A bit value of
0 indicates that the corresponding attribute is not present.
B8
B7
B6
B5
B4
B3
reserved reserved reserved reserved reserved LAS
Schedule
in Non-volatile
Memory

DlmeLinkMasterInfoRecord

PrimaryLinkMasterFl
agVariable

B2
Last
Values

B1 (lsb)
Link
Master

Record
Supported

Statistics Record
Supported

This attribute specifies information of DL Link Master related management. Its


attributes are defined in the Dlme Link Master Information Class. This record is
writeable for all Link Master capable devices using FMS Write.req. The NMA
returns a positive response if no validation is done or if the validation of the
data is successful. The new values take effect immediately.
The default value of this attribute is FALSE. When this flag is set to TRUE, this
node is the primary Link Master. A write to this variable orders the receiving
Link Master to try to become the LAS. If the Link Master becomes the LAS, it
returns an FMS Write.rsp(+). If this attempt fails, it sends an FMS Write.rsp(-).
The behavior is described in the DLL portion of the specification.
NOTE: It is a configuration error to have more than one device on a link
configured as the Primary Link Master.
FMS Object Name:
Object Type:
Data Type:
Length:
FMS Access Right:

PrimaryLinkMasterFlagVariable
Simple Variable
Boolean
1
RaWa

Element = PrimaryLinkMasterFlagVariable
1. The value of this variable may be set to TRUE only through an FMS Write
or through a local interface.
2. When the value of this variable is TRUE and the device is attached to the
network at one of the default addresses, the NMA regards the value as a
configuration value and does not attempt to acquire the LAS.
3. When the value of this variable is TRUE or when an FMS Write.ind is
received to set it to TRUE by the NMA of a Link Master device that is not
the LAS and that is attached to the network at an assigned address (not
one of the default addresses), the NMA instructs the DLME to acquire the
LAS. Two outcomes are possible:
If the DLME indicates that the attempt has failed, the NMA sets the
value of this variable to FALSE. If an FMS Write response is
pending, the NMA returns a negative response.
If the request succeeds on either the first or the second attempt,
the NMA sets the value of this variable to TRUE (if not already
TRUE). If an FMS Write response is pending, the NMA returns a
positive response.

466

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

Table 10 DlmeLinkMasterInfo (continued)


Name
LiveListStatusArrayVariable

Description

This attribute is an OctetString of 32 Octets in which each bit represents a node


address on the segment. A value of "1" indicates that the device is
communicating on the segment, and a value of "0" indicates that the device is
not communicating on the segment. The first bit corresponds to node address
0x00. The last bit corresponds to node address 0xFF. The range of valid node
addresses is 0x10 ... 0xFF. It is represented in FMS as:
FMS Object Name:
Object Type:
Data Type:
Length:
FMS Access Right:

PrimaryLinkMasterFlagVariable
Simple Variable
OctetString
32
Ra

The first bit is the first bit that is transmitted and the last bit is the last bit that is
transmitted on the bus. For example, for a device with a node address of 16
(decimal) the following would be transmitted on the bus:

MaxTokenHoldTime
Array

BootOperatFunctionalClass

CurrentLinkSettings
Record
ConfiguredLinkSettingsrecord

DlmeLinkMasterStatisticsRecord

LastValuesRecord

R610
11/99

Bit Number
0-7
8 - 15
16 23
Octet String
0x00
0x00
0x80

This attribute is an array of 8 OctetString elements. Each element in the array is


64 octets long. Each 64 Octet array element contains 32 values. Each value
consists of 2 octets that indicates the initial amount of local link capacity for
each active node in the LiveListStatusArrayVariable. The order of values
corresponds to the order of nodes in the LiveListStatusArrayVariable. These
values are defined in the IEC/ISA DL Specification Part 4 chapter 5.7.5.10. This
attribute is represented in FMS as:
FMS Object Name: MaxTokenHoldTimeArray
Object Type:
Array
Data Type:
OctetString
Length:
8
FMS Access Right: RaWa
This attribute specifies how the device should function in the network the next
time it boots up. This permits the NMgr to configure a device capable of being a
Link Master as a Basic device. Also, a Bridge can be configured to be Link
Master or a Basic device. A NMgr configures this attribute using FMS write. The
NMA returns a positive response to the write if a valid value is written.
This record reflects the current settings for the link. Its attributes are defined in
the DlmeLinkSettings record. For Link Master devices that are not acting as the
LAS, this represents the settings received from the LAS.
This represents the desired configuration of DLL and PhL management
information for the link, This attribute is writeable using FMS Write.req for all
Link Master capable devices. The NMA returns a positive response to the write
request if no validation is done or if the validation is successful. If the device is
or becomes LAS, and if the values are different from the
CurrentLinkSettingsRecord, the LAS should clear its live list and reconstruct it
using the normal link maintenance procedures. The attributes of this record are
defined in the DlmeLinkSettings record.
This attribute specifies statistics information of DL Link Master related
management. Its attributes are defined in the Dlme Link Master Statistics Class
in addition to the Dlme Basic Statistics Class. This record is supported if the
Link Master Statistics Record Supported bit of the
DlmeLinkMasterCapabilitiesVariable is set to TRUE.
This attribute contains information monitored immediately before a
NumLasRoleDeleg/Claim/DelegTokenHoldTimeout occurred.

HPM Parameter Reference Dictionary


Honeywell Inc.

467

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.4.7 PLMEBASICINFO
Table 11 lists and describes the Attributes for PlmeBasicInfo (Class).
Table 11 PlmeBasicInfo
Name
InterfaceMode

Description
This element is defined in ISA/IEC Chapter 6.2, and is coded as described
below:
B8
B7
B6
B5
B4
B3
reserved reserved reserved reserved reserved reserved

B2
reserved

B1 (lsb)
Interface
Mode
Half Duplex
Full Duplex

LoopBackMode

This element is defined in ISA/IEC Part 2 Chapter 6.2. It is coded as described


below:
B8
B7
B6
B5
B4
B3
reserved reserved reserved reserved reserved reserved

B2
B1 (lsb)
reserved LoopBackMode
Diabled
MAU
MDS

XmitEnabled

B7
Chan 7

B6
Chan 6

B5
Chan 5

B4
Chan 4

B3
Chan 3

B2
Chan 2

B1 (lsb)
Chan 1

This variable indicates whether or not reception is enabled on a channel.


Transmission is enabled when value is 1.
B8
B7
Chan 8 Chan 7

PreferredReceiveChannel

00
01
10

This variable indicates when transmission is enabled on a channel.


Transmission is enabled when value is 1.
B8
Chan 8

RevEnabled

0
1

B6
Chan 6

B5
Chan 5

B4
Chan 4

B3
Chan 3

B2
Chan 2

B1 (lsb)
Chan 1

This element is defined in ISA/IEC Part 2 Chapter 6.2, and is coded as described
below:
B8
B7
B6
B5
B4
B3
B2
B1 (lsb)
reserved reserved reserved reserved - - - - - - - PreferredReciveChannel - - - None
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8

MediaTypeSelected

ReceiveSelect

468

0000 = 0
0001 = 1
0010 = 2
0011 = 3
0100 = 4
0101 = 5
0110 = 6
0111 = 7
1000 = 8

This element defines which media type is currently selected. The number
corresponds to the position of the specified medium in the
MediumAndDataRagesSupported attribute in the DlmeBasicCharacteristics
class.
This element defines the channel number that is currently supported. Its values
are the same as those defined for the PreferredReceiveChannel attribute.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.5
SYSTEM MANAGEMENT PARAMETERS
The System Management Directory Entry values provide information about the number of
System Management objects and the address of the objects in the device. This directory
(Table 12) is supplied by the manufacturer and is not changeable by a user.
Table 12 System Management Directory Entry
Directory Entry

Description

DirectoryRevisionNumber
NumberOfDirectoryObjects
TotalNumberOfDirectoryEntries

DirectoryIndexOfFirstCompositeListReference
NumberOfCompositeListReferences
SmAgentStartingOdIndex
NumberOfSmAgentObjects
SynchAndSchedulingStartingOdIndex

NumberOfSyncAndSchedulingObjects
AddressAssignmentStartingOdIndex
NumberOfAddressAssignmentObject
VfdListStartingOdIndex

NumberOfVfdListObjects

FbScheduleStartingOdIndex
NumberOfFbScheduleObjects

R610
11/99

This entry identifies the revision level of the Directory Object (1).
This entry identifies the total number of directory objects (1).
This entry identifies the total number of references, excluding the
directory header, in a single directory (5). Each reference is
st
composed of two unsigned16 array entries. The 1 reference is
the SM Agent reference.
st
This directory entry is the directory entry number of the 1
composite list reference (0). There are none currently defined.
Number of composite list references (0). None are defined.
The starting OD Index for SM Agent object. The objects are as
follows: SMSupport, T1, T2, and T3.
The number of SM Agent parameters (4).
The starting OD Index for the Synch and Scheduling Objects.
The objects are as follows: Current_Time, LocalTimeDiff,
ApClockSyncInterval, TimeLastRcvd, PrimaryApTimePublisher,
TimePublisherAddr, spare, and MacroCycleDuration.
Number of Synch and Scheduling objects (8).
The starting OD Index of the Address Assignment objects:
DeviceId (read only), PdTag, Operational_Powerup (read only).
The number of Address Assignment Objects (3).
The starting OD Index of the VFD list. This is a list of
VFD_REF_ENTRY object that represents the Virtual Field
Devices in the Physical device.
The number of VFD_REF_ENTRY objects in the list. For most
basic devices this is (2). One for the Management VFD and one
for the Application VFD.
The starting OD Index for the Function Block Schedule Objects.
This is a list of FB_START_ENTRY objects.
The number of Function Block Scheduling objects.

HPM Parameter Reference Dictionary


Honeywell Inc.

469

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.5.1 SYSTEM NETWORK MANAGEMENT PARAMETERS


Table 13 contains the System Network Management Parameters.
Table 13 System Network Management Parameters
System Network Management
Parameter
ApClockSyncInterval

Current_Time

FB_Start_Entry

LocalTimeDiff

MacrocycleDuration

PrimaryApTimePublisher

SMSupport

T1

T2

T3

Vfd_Ref_Entry

470

Description
AP Clock Synchronization Interval is the interval in seconds between
time messages on the link. It is set by system management during
node address assignment.
Current Time is the application clock time. It is updated by system
management, and the application clock synchronization service is used
to keep it coordinated with the application clocks of other devices on the
extended link,. Its value represents the number of 1/32 millisecond
ticks since January 1, 1972.
Function Block Schedule. It is used to represent an entry in the function
block starting schedule. The START_TIME_OFFSET element is in the
units of time maintained by the data link layer, each count representing
1/32 of a millisecond. A value of FFFFFFFF(hex) for this element
indicates an unused entry.
See FF Data Type 91.
Local Time Difference is used to calculate the local time from
CURRENT_TIME. It is specified as the number of (+/-) 1/32 millisecond
ticks to add to the clock to obtain the local time.
Macrocycle Duration is the length of the macrocycle in 1/32 of a
millisecond ticks. The maximum value represents a duration of
approximately 37 hours. The MacroCycle duration is the least common
multiple of the Function Block Schedules durations.
Primary AP Time Publisher is the node address of the primary time
publisher for the local link. It is set by system management during node
address assignment. It is a configuration error if the SM_SUPPORT
variable of the device specified by this node address does not have the
Application Clock Synchronization (Time Publisher) feature bit set.
SM Support indicates which features are supported by the System
Management Kernel in this device. The features are mapped to the bits
in the bit string.
T1 is the preset value for the SM step timer in 1/32 of a millisecond
ticks. The default value is specified by the communications profile for
the application area.
T2 is the preset value for the SM set address sequence timer in 1/32 of
a millisecond ticks. The default value is specified by the
communications profile for the application area.
T3 is the preset value for the set address wait timer in 1/32 of a
millisecond ticks. The default value is specified by the communications
profile for the application area.
There will be a number of VFD List Objects entries identifying the VFDs
in this device. This list identifies, using values local in scope, the virtual
field devices that exist in this physical device. These values are the
same as those used for the FmsVfdID attribute of the VcrStaticEntry
objects in the NMIB. The VFD tags may be assigned by the user. They
may optionally be set with the FMS write service, but the reference
values should not be changed and will be verified during the write if this
capability is supported. In addition, the server must check that the tag
is unique within this list, and that it is not blank (containing all spaces).

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Supported Function and Transducer Blocks/Network management and System Management Parameters

7.6 VFD APPLICATION PARAMETERS


Table 14 VFD Application Directory
Directory Entry
DirectoryRevisionNumber
NumberOfDirectoryObjects
TotalNumberOfDirectoryEntries
DirectoryIndexOfFirstCompositeListReference

NumberOfCompositeListReferences
OdIndexForStartingActionObject
NumberOfActionObjects
OdIndexOfTheStartingLinkObjectInTheVfd
NumberOfLinkObjectsInTheVfd
OdIndexOfTheStartingAlertObjectInTheVfd
NumberOfAlertObjectsInTheVfd
OdIndexOfTheStartingTrendObjectInTheVfd
NumberOfTrendObjectsInTheVfd
OdIndexOfTheStartingDomainObjectInTheVfd
NumberOfDomainObjectsInTheVfd
DirectoryIndexForTheResourceBlock
NumberOfResourceBlocksInTheVfd

DirectoryIndexForTheFirstTransducerBlockPointer
NumberOfTransducerBlocksInTheVfd
DirectoryIndexForTheFirstFunctionBlockPointer
NumberOfFunctionBlocksInTheVfd

R610
11/99

Description
Current revision number of the directory structure.
The number of directory object. Multiple directory objects
are contiguous in the OD. Normally 1.
The total number of references, excluding the directory
header. The first reference is for Action Objects.
This is the directory index for the composite object after the
Domain Entry (17). This is normally the Resource Block
Composite Object.
The number of Composite List References (3).
Starting OD Index for the Action Objects in this VFD.
The number of Action Objects.
Starting OD Index for the Link Objects in this VFD.
The number of Link Objects allocated to this VFD.
The starting OD Index of the Alert Objects in this VFD.
The number Alert Objects in this VFD.
The starting OD Index for the Trend Object in this VFD.
The number of Trend Objects in this VFD.
The starting OD Index for application Domain Objects in this
VFD.
The number of application Domain Objects in this VFD.
Index in this directory for the Resource Block (23).
The number of resource Blocks in the VFD (always 1).

Index in this directory for the first Transducer Block OD


Index (25).
The number of Transducer Blocks in this VFD.
Index in this directory for the first Function Block OD Index.
The number of Function Blocks in this VFD.

HPM Parameter Reference Dictionary


Honeywell Inc.

471

Supported Function and Transducer Blocks/Network management and System Management Parameters

472

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FIELDBUS PARAMETER DEFINITIONS (A THROUGH X)

This section contains descriptions of the Fieldbus Foundation parameters. The


parameter descriptions are listed in alphabetical order according to the parameter
name.

-AAccept_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Discrete
13
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Generated when the Accept_D switch is used.

Accept_D
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
Causes PV_D to become a copy of Out_D.
1
Contained
Dynamic
1,3
Fieldbus Device
0 Off
1 Accept

Accept_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Priority of accept alarm.

HPM Parameter Reference Dictionary


Honeywell Inc.

473

Ack_Option

Ack_Option
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Bit String
Defines of whether alarms associated with the function block will be
2
automatically acknowledged.
Contained
Static
4
Fieldbus Device
0 Disable/Enable Discrete Alarm
8 Disable/Enable Alarm 8
1 Disable/Enable High High Alarm
9 Disable/Enable Alarm 9
2 Disable/Enable High Alarm
10 Disable/Enable Alarm 10
3 Disable/Enable Low Low Alarm
11 Disable/Enable Alarm 11
4 Disable/Enable Low Alarm
12 Disable/Enable Alarm 12
5 Disable/Enable Deviation High Alarm 13 Disable/Enable Alarm 13
6 Disable/Enable Deviation Low Alarm 14 Disable/Enable Alarm 14
7 Disable/Enable Block Alarm
15 Disable/Enable Alarm 15

Act_Fail_Action
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
Specifies the action the actuator takes in case of failure.
1
Contained
Static
4
Fieldbus Device
0 Undefined
3 HoldLastValue
1 SelfClosing
4 MaximumValue
2 SelfOpening
255 Indeterminate
5 MinimumValue

Act_Man_Id
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

474

Unsigned16
2
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
The actuator manufacturer's identification number as defined by FOUNDATION
Fieldbus.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Act_Mod_Num

Act_Mod_Num
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
Defines the actuator's model number.

Visible String
32
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
Defines the actuators serial number.

Act_Sn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm_Hys
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
0-50 %

Description:
Determines the amount that the PV must return within the alarm limits before
the alarm condition clears. Alarm hysteresis expressed as a percent of the span
of the PV.

Alm_Rate_Dn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Description:
Float
Defines the ramp rate of change of upward alarm expansion.
4
Contained
Static
4
Fieldbus Device
Any Positive Value

HPM Parameter Reference Dictionary


Honeywell Inc.

475

Alm_Rate_Up

Alm_Rate_Up
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Defines the ramp rate of change of downward alarm expansion.

Alarm_Sum
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Summary Description:


Specifies the current alert status, unacknowledged states, unreported states, and
8
disabled states of the alarms associated with the function block.
Contained
Mixed
1, 4
Fieldbus Device
N/A

Alert_Key
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

476

Unsigned8
1
Contained
Static
4
Fieldbus Device
1-255

Description:
Defines the identification number of the plant unit. This information may be
used in the host for sorting alarms, etc.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Arith_Type

Arith_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
Specifies the ID number of the arithmetic algorithm.
1
Contained
Static
4
Fieldbus Device
FlowCompensationLinear
1
6 Average
FlowCompensationSQRoot
2
7 Summer
FlowCompensationAppx
3
8 ForthOrderPoly
BTUFlow
4
9 HTGCompensatedLevel
MultiplyDivide
5

Auto_Cycle
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned8
1
Contained
Static
2
Fieldbus Device
N/A

Description:
When true, resets time to start of first step.

HPM Parameter Reference Dictionary


Honeywell Inc.

477

Bal_Time

-BBal_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
positive

Description:
Specifies the time (in seconds) for the internal working value of bias or ratio to
return to the operator set bias or ratio. In the PID block, it may be used to
specify the time constant at which the integral term will move to obtain balance
when the output is limited and the mode is Auto, Cas, or RCas.

Float
4
Contained
Non-Volatile
1, 3
Fieldbus Device

Description:
Specifies the bias value used in computing the function block output, expressed
in engineering units.

Bias
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Reference

OUT_SCALE +/- 10%

Bias_In_1 - Bias_In_3
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
5
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies the value of the constant to be added to IN_1, IN_2, and IN_3,
respectively.

Binary_Cl
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: 0-50

478

Description:
Specifies the priority discrete setpoint that commands the actuator closed.

Reference

OUT_SCALE +/- 10%

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Binary_Op

Binary_Op
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
Specifies the priority discrete setpoint that commands the actuator open.

BkCal_Hys
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
0-50%

Description:
Specifies the amount that the block output must change away from its output
limit before the limit status is turned off, expressed as a percent of span of the
output.

BkCal_In
FF Data Type: Value & Status - Description:
Floating Point
The value and status used for backwards tracking of the output, provided by a
link to a downstream blocks back calculation output parameter.
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

BkCal_In_1 - BkCal_In_2
FF Data Type: Value & Status - Description:
Floating Point
The back-calculated input value and status required for a splitter.
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

479

BkCal_In_D

BkCal_In_D
FF Data Type: Value & Status - Description:
Discrete
The back-calculated input required for a control block.
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

BkCal_Out
FF Data Type: Value & Status - Description:
Floating Point
The output value and status provided to an upstream block for output tracking
when the loop is broken or limited, as determined by the status bits. This
Length: 5
information is used to provide bumpless transfer to closed loop control and to
Usage: Output
prevent windup under limited conditions when that becomes possible.
Storage: Dynamic
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

BkCal_Out_D
FF Data Type: Value & Status - Description:
Discrete
The output value and status provided to an upstream block output tracking
when the loop is broken, as determined by the status bits. This information is
Length: 2
used to provide bumpless transfer to closed loop control.
Usage: Output
Storage: Dynamic
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

BkCal_Sel_1 - BkCal_Sel_3
FF Data Type: Value & Status Floating Point
Length: 5
Usage: Output
Storage: Dynamic
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

480

Description:
Control selector output value and status associated with SEL_1, SEL_2, or
SEL_3 input, which is provided as the back calculation input to the upstream
block that is linked to SEL_1, SEL_2, or SEL_3, respectively.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Block_Alm

Block_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Discrete
13
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Defines the block alarm that is used for all configuration, hardware, connection
failure or system problems in the block. The cause of the alert is entered in the
subcode field. The first alert to become active will set the active status in the
Status attribute. As soon as the unreported status is cleared by the alert reporting
task, another block alert may be reported without clearing the active status, if
the subcode has changed.

Block_Execution_Sequence
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:

Integer
4
Contained
N/A
N/A
TPSB Only
0-119

Specifies the blocks execution sequence within a control loop. Used in function
block scheduling.

BlockName
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
TPSB Only
N/A

Description:
Defines the block name for Meta Data.

N/A
N/A
N/A
N/A
N/A
TPSB Only
0-100

Description:
Defines the transducer block number in a VFD or function block number in a
VFD.

BlockNo
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

481

Block_Err

Block_Err
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Bit String
Reflects the error status associated with the hardware or software components
2
that are associated with a block. It is a bit string, so that multiple errors may be
Contained
shown.
Dynamic
1, 3
Fieldbus Device
OutputFailure
0 Other
8
MemoryFailure
1 BlockConfiguration
9
2 LinkConfiguration
10 LostStaticData
3 SimulationActive
12 ReadbackCheck
4 LocalOverride
13 MaintenanceNeeded
5 DeviceFaultState
14 PowerUp
6 DeviceMaintenance
15 OutOfService
7 InputFailure

Block_Index
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Identifies the starting object dictionary index of a block.

Unsigned16
2
N/A
N/A
N/A
CFF File
0-16384

Block_Tag
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

482

Visible String
32
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
Specifies the tag name of the block. The tag name is to be unique throughout the
control system on one link.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Body_Temp

Body_Temp
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
The instruments body temperature value and status available to the function
block.

Body_Temp_Unit
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
4
Fieldbus Device
N/A

Description:
The instruments engineering units code for the body temperature.

Block_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
Contained
N/A
N/A
CFF File
N/A

Description:
Specifies one of the FF block types. For example, AI, PID, AO, and etc. The
manufacturer names custom block types.

ByPass
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
The normal control algorithm may be bypassed through this parameter. When
1
bypass is set, the setpoint value (in percent) will be directly transferred to the
Contained
output. To prevent a bump on transfer to/from bypass, the setpoint will
Static
automatically be initialized to the output value or process variable,
2
respectively, and the path-broken flag will be set for one execution.
Fieldbus Device
1 Off
2

R610
11/99

On

HPM Parameter Reference Dictionary


Honeywell Inc.

483

Cal_Min_Span

-CCal_Min_Span
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
The minimum calibration span allowed. Ensures that the two calibrated points
(high and low) are not too close.

Cal_Point_Hi
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
2
Fieldbus Device
N/A

Description:
The highest calibrated value on a tranducer block.

Cal_Point_Lo
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
2
Fieldbus Device
N/A

Description:
The lowest calibrated value on a transducer block.

Cal_Propogate_Vel
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

484

Float
4
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
The calibrated propagation velocity of the radar pulse.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Calc_Errrs

Calc_Errrs
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Bit String
Displays the types of calibration errors.
2
Contained
Dynamic
4
Fieldbus Device
Non-SpecificError
0
7 IllegalOperator
DivideByZero
1
8 JMP-OutOfList
Overflow
2
9 InvalidDataType
FunctionError
3
10 TypeConversionFailed
FunctionCallNotSupported
4
11 ST-Disallowed
FuntionCallArgumentCount
5
12 StackOverflow
FunctionCallArgumentType
6
13 INST_EX_LIM-Count

Cal_Unit
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
4
Fieldbus Device
N/A

Description:
The device-description engineering-units-code index for the calibration values.

Cas_In
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
The remote setpoint value, which must come from another fieldbus block, or
from an HPM point through an output connection.

HPM Parameter Reference Dictionary


Honeywell Inc.

485

Cas_In_D

Cas_In_D
FF Data Type: Value & Status - Description:
Discrete
The remote setpoint value, which must come from another discrete fieldbus
block, or from an HPM point through an output connection.
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Cfm_Act1_Time - Cfm_Act2_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
The maximum time allowed to confirm the first active state and second active
state, respectively.

Cfm_Pass_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
The maximum time allowed to confirm the passive state.

Unsigned16
2
Contained
Static
4
Fieldbus Device
1-to Mfg.
Limit

Description:
The number of the logical hardware channel that is connected to this I/O block.
This information defines the transducer to be used to interface with the physical
world. The I/O block may not transition from OOS mode unless a non zero
channel number is entered.

Channel
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

486

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Channel_Map

Channel_Map
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
N/A
Fieldbus Device
N/A

Description:
An optional parameter that aids in the correlation of channels in a device to
channels as defined for a plant or process.

CheckBack
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Bit String
Displays status of final control element.
2
Contained
Dynamic
1, 3
Fieldbus Device
Stat_Safeguard_OP
0
8 Stat_Rb_D_CL
Stat_Safeguard_CL
1
9 Stat_Torque_D_OP
Stat_Binary_OP
2
10 Stat_Torque_D_CL
Stat_Binary_CL
3
11 Stat_Sub_Mode
Stat_Disc
4
12 Stat_Trav_Time
Stat_Disc_D_Op
5
13 Reserved1
Stat_Disc_D_CL
6
14 Reserved2
Stat_Rb_D_OP
7

Clock_Per
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Elapsed time (in hours) of periodic reset.

HPM Parameter Reference Dictionary


Honeywell Inc.

487

Clr_Fstate

Clr_Fstate
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Dynamic
N/A
Fieldbus Device
0 Uninitialized

Description:
Writing a Clear to this parameter will clear the device faultstate state provided
the field condition, if any, has cleared.

1 Off
2 Clear

Collection_Directory
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
4
Contained
Static
N/A
Fieldbus Device
N/A

Description:
A directory that specifies the number, starting indices, and device-description
item IDs of the data collections in each transducer within a transducer block.

Comb_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

488

Description:
Unsigned8
Determines how multiple IN_D values are combined in the timer function.
1
Contained
Static
4
Fieldbus Device
0 AND
22 EXACTLY2
1 OR
23 EXACTLY3
ANY2
2
40 EVEN
3 ANY3
41 ODD
21 EXACTLY1

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Comp_Hi_Lim

Comp_Hi_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the high limit for the PV compensation term.

Comp_Lo_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the low limit for the PV compensation term.

Cond_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Length of conditioning time (in seconds).

Cond_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned8
1
Contained
Static
4
Fieldbus Device
None
0
Delay
1
Extend
2

Description:
Defines the type of conditioning applied to PV_D in the discrete alarm function.

3
4
5

Debounce
Pulse
RT_Pulse

HPM Parameter Reference Dictionary


Honeywell Inc.

489

Confirm_Time

Confirm_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
4
Contained
Static
2
Fieldbus Device
N/A

Description:
The minimum time between retries of alert reports.

Control_Opts
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Bit String
Options which the user may select to alter the calculations done in one of the
2
following control block options: CS, PD, RA, BG, PID, or ML.
Contained
Static
4
Fieldbus Device
0 Bypass_Enable
7 Track_Enable
1 SP-PV_Track_Man
8 Track_in_Manual
2 SP-PV_Track_Rout
9 PV_for_BkCal_Out
3 SP-PV_Track_LO-IMan
10 Bias_may_be_adjusted
4 SP_Track_retain
11 Use_BKCAL_OUT_with_IN
5 Direct_Acting
12 Restrict_SP_to_limits_in_Cas_and_RCas
6 Reserved
13 No_output_limits_in_Man

ControlType
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

490

N/A
N/A
N/A
N/A
N/A
TPSB Only
N/A

Description:
Defines the type of control. This parameter is used by the TPSB internally to
distinquish different types of strategies. For example, a function block, a
transducer block, a device, and a VFD application are different control types.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Crack_Time

Crack_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
The maximum time (in seconds) allowed to drop previous confirm.

Crack_Timer
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Dynamic
4
Fieldbus Device
N/A

Description:
Shows time (in seconds) taken to drop the confirm.

Float
4
Contained
Static
N/A
Fieldbus Device
N/A

Description:
Defines X coordinate of curve.

Float
4
Contained
Static
N/A
Fieldbus Device
N/A

Description:
Defines Y coordinate of curve.

Curve_X
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Curve_Y
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

491

Cycle_Sel

Cycle_Sel
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Bit String
2
Contained
Static
2
Fieldbus Device
0 Scheduled

Description:
Used to select the block execution method for this block.

1 Block_Execution
2 Manuf_Specific

Cycle_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

492

Description:
Bit String
Identifies the block execution methods available for this resource.
2
Contained
Static
4
Fieldbus Device
Scheduled
0
Block_Execution
1
Manuf_Specific
2

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DC_State

-DDC_State
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
Displays the current state of the device control function.
1
Contained
Dynamic
1, 3
Fieldbus Device
0 ConfirmedPassive
7 FailedState_1
1 ConfirmedState_1
8 FailedState_2
2 ConfirmedState_2
9 Tripped
3 GoingToPassive
10 LostInterlock
4 GoingToState_1
11 Locked
5 GoingToState_2
12 LostMCCPower
6 FailedPassive

DD_ITEM
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
4
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
A unique number which identifies the description of the object that is
developed as part of its device description.

DD_MEMBER
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned32
4
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
A unique number which identified the function of the block that is developed as
part of its device description.

HPM Parameter Reference Dictionary


Honeywell Inc.

493

DD_RESOURCE

DD_RESOURCE
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
Contained
Static
N/A
Fieldbus Device
N/A

Description:
Identifies the tag of the resource that contains the device description.

Unsigned16
2

Description:
Revision of the device description associated with the resource - used by an
interface device to locate the device description file for the resource.

DD_REV
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Static
N/A
Fieldbus Device
N/A

DD_REVIS
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
The device description revision number assigned to this block.

Dead_Band
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

494

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Interval where changes in input do not affect output

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Dead_Time

Dead_Time
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: 0-213900000

Description:
Delay time (in seconds) for the input value.

Delay_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies the time (in seconds) to delay a change in SP_D to active.

Delay_Timer
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Dynamic
4
Fieldbus Device
N/A

Description:
Shows the time (in seconds) of several delay functions.

HPM Parameter Reference Dictionary


Honeywell Inc.

495

Description

Description
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
CFF File
N/A

Description:
Fieldbus device description used in the CFF Value File.

Visible String
32
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Device identifier that is universally unique.

Unsigned16
2
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Manufacturer revision number associated with the resource - used by an
interface device to locate the device-description file for the resource.

Dev_Id
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Dev_Rev
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Dev_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

496

Unsigned16
2
Contained
Static
4
Fieldbus Device
N/A

Description:
Manufacturers model number associated with the resource - used by interface
devices to locate the device-description file for the resource.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Device_Opts

Device_Opts
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Bit String
Options used in processing the device control function.
2
Contained
Static
4
Fieldbus Device
Interlock
Trip
0
4
TrackSPInLO
LostPower
1
5
Permissive
PassiveWhenConfigured
2
6
ResetRequired
BusRestartPassive
3
7

DeviceClass
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
Defines the device functional class. This parameter is resides only in the
1
Capabilities or Value file.
N/A
N/A
N/A
CFF File
Undefined
0
Basic
1
Linkmaster
2
Bridge
3

Disable_1 - Disable_4
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0
Use
Disable
1

R610
11/99

Description:
The disable or use input switch for the respective input selector function.

HPM Parameter Reference Dictionary


Honeywell Inc.

497

Disc_Alm

Disc_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Discrete
13
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
The status and time stamp associated with the discrete alarm.

Disc_Cond
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the condition of Out_D, the primary discrete output value.

Disc_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
PV State

Description:
Defines the state of the discrete input which will generate an alarm.

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Defines the priority of the discrete alarm.

Disc_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

498

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

DV_Hi_Alm

DV_Hi_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Float
16
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Displays the current status and time stamp associated with the high deviation
alarm.

DV_Hi_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
Defines the value of the high deviation alarm limit in engineering units.
4
Contained
Static
4
Fieldbus Device
0- to PV Span, +INF

DV_Hi_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Defines the priority of the high deviation alarm.

DV_Lo_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Alarm Float
16
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Displays the status and time stamp associated with the low deviation alarm.

HPM Parameter Reference Dictionary


Honeywell Inc.

499

DV_Lo_Lim

DV_Lo_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
Defines the value of the low deviation alarm limit in engineering units.
4
Contained
Static
4
Fieldbus Device
- PV Span to 0, -INF

DV_Lo_Pri
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range:0-15

500

Description:
Defines the priority of the low deviation alarm.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Execution_Period

-EExecution_Period
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
4
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
The time (in 1/32 milliseconds ) between initiation of block execution - for
periodic execution

ElementName
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
TPSB Only
N/A

Description:
Defines the name of the element strategy associated with the LAS Schedule.

En_Close
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
When active, allows close commands

En_Open
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
When active, allows open commands

HPM Parameter Reference Dictionary


Honeywell Inc.

501

Err_Latch

Err_Latch
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies whether error indicators are to be retained in the Calc_Errrs,
paramaters, etc.

EXECUTION_TIME
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
4
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
The total time (in 1/32 milliseconds) required for the block algorithm to
execute

Expand_Dn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Dynamic
1, 3
Fieldbus Device
N/A

Description:
Amount Lo and Lo_Lo are expanded after a change in the setpoint

Expand_Up
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

502

Float
4
Contained
Dynamic
1, 3
Fieldbus Device
N/A

Description:
Amount Hi and Hi_Hi are expanded after a setpoint change

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Fail

-FFail
FF Data Type: Unsigned16
Description:
Enumeration of the current failure condition
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 1,3
Classification: Fieldbus Device
PassiveConfirmTime
Tripped
7
Range: 1
2
3
4
5
6

State_1ConfirmTime
State_2ConfirmTime
PassiveConfirmLost
State_1ConfirmLost
State_2ConfirmLost

8
9
10
11
12

LostInterlock
LockedOut
LostPower
MultipleConfirms
MultipleConfirms

Fail_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Discrete
13
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Generated when a confirm times out or is lost

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Priority of the fail alarm

Fail_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

503

Fault_State

Fault_State
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0 Uninitialized
1

Clear

Active

Description:
Condition set by loss of communication to an output block, failure promoted to
an output block or a physical contact. When faultstate condition is set, then
output function blocks will perform their FSTATE actions.

FB_CIDST
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

N/A
N/A
N/A
N/A
N/A
TPSB Only
N/A

Description:
Function Block Control Input Destination.
Defines the input parameter within the function block that is the destination for
the value

FB_CISRC
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

504

N/A
N/A
N/A
N/A
N/A
TPSB Only
N/A

Description:
Function Block Control Input Source.
Defines the parameter that provides the value to the function block. The
parameter is normally an output parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FB_CITYPE

FB_CITYPE
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Function Block Control Input LinkageType. Linkage type may be one of the
following: Not Configurer, Local, Client or Subscriber.

N/A
N/A
N/A
N/A
N/A
TPSB Only
N/A

FB_NoCIn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Defines the number of control inputs to a function block

N/A
N/A
N/A
N/A
N/A
TPSB Only
N/A

Feature_Sel
FF Data Type: Bit String
Length: 2
Usage: Contained
Storage: Static
Valid View(s): 2
Classification: Fieldbus Device
Range: 0 Unicode

Description:
Used to select resource block options that are associated with the Features
parameter.

1 Reports
2
3
4
5
6
7

R610
11/99

Fault_State
Soft_W_Lock
Hard_W_Lock
Out_Readback
Direct_Write
ChangeBypass
InAutoMode

HPM Parameter Reference Dictionary


Honeywell Inc.

505

Features

Features
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Bit String
2
Contained
Static
4
Fieldbus Device
0
1
2
3
4
5
6
7

Description:
Used to show supported resource block options.

Unicode
Reports
Fault_State
Soft_W_Lock
Hard_W_Lock
Out_Readback
Direct_Write
ChangeBypassI
nAutoMode

FF_Gain
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
The gain that the feed forward input is multiplied by before it is added to the
calculated control output.

FF_Scale
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

506

Scaling
11
Contained
Static
4
Fieldbus Device
0-100

Description:
The feed forward input high and low scale values, engineering units code, and
number of digits to the right of the decimal point.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FF_Val

FF_Val
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
The feed forward value and status.

Field_Val
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Raw value of the field device in % of PV range, with a status reflecting the
transducer condition, before signal characterization (L_TYPE) or filtering
(PV_FTIME).

Field_Val_D
FF Data Type: Value & Status Description:
Discrete
Raw value of the field device discrete input, with a status reflecting the
transducer condition.
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

FileDate
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Visible String
32
N/A
N/A
N/A
CFF File
N/A

Description:
Capabilties file date or Value file date.

HPM Parameter Reference Dictionary


Honeywell Inc.

507

FileType

FileType
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
CFF File
N/A

Description:
Defines the file type (capability or value)

Final_Position_Value
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
The actual valve position and status. Could be used as the
READBACK_VALUE in an AO block

Final_Value
FF Data Type: Value & Status
Floating point
Length: 5
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
The proposed valve position and status written by an analog output function
block

Contained
Non-Volatile
1, 3
Fieldbus Device
N/A

Final_Value_Cutoff_Hi
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

508

Description:
Float
Defines the cutoff high limit of the porposed value position
4
Contained
Static
4
Fieldbus Device
Final_Value_Range,
+INF

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Final_Value_Cutoff_Lo

Final_Value_Cutoff_Lo
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
Defines the cutoff low limit of the proposed value position
4
Contained
Static
4
Fieldbus Device
Final_Value_Range, INF

Final_Value_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
The proposed valve position and status written by a discrete function block

Final_Value_Range
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
1, 3
Fieldbus Device
N/A

Description:
The high and low range limit values, the engineering units code and the number
of digits to the right of the decimal point to be used to display the final value

Follow
FF Data Type: Value & Status Description:
Discrete
If tracking is on, the output tracks the input
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0
Off
Follow
1

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

509

Free_Space

Free_Space
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Dynamic
2
Fieldbus Device
0-100%

Description:
Percent of memory available for further configuration. Zero in a preconfigured
device.

Free_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Dynamic
1, 3
Fieldbus Device
0-100%

Description:
Percent of the block processing time that is free to process additional blocks.

FState_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
positive

Description:
Faultstate Time. The time in seconds from detection of failure of the output
block remote setpoint to the output action of the block output if the condition
still exists.

FState_Val
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

510

Description:
Float
The preset analog SP value to use when failure occurs. This value will be used
4
if the I/O option Faultstate-to-value is selected.
Contained
Static
4
Fieldbus Device
PV_SCALE +/- 10%

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

FState_Val_D

FState_Val_D
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned8
1
Contained
Static
4
Fieldbus Device
N/A

Description:
The preset discrete (SP_D) value to use when failure occurs. This value will be
used if the I/O option Faultstate-to-value is selected.

HPM Parameter Reference Dictionary


Honeywell Inc.

511

Gain

-GGain
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Dimensionless value used by the block algorithm in calculating the block
output.

Gain_In_1 Gain_In_3
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Constant to be multiplied by (IN_n + bias)

Good_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
0-100

Description:
Sets the limit for percentage of inputs with good status (PCT_INCL)

Grant_Deny
FF Data Type: Access
Permissions
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 2
Classification: Fieldbus Device
Range: 0 Program
1 Tune

512

Description:
Options for controlling access of host computers and local control panels to
operating, tuning, and alarm parameters of the block.

Alarm

Local

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Hard_Types

-HHard_Types
FF Data Type: Bit String
Length: 2
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Scaler_Input

Description:
The types of hardware available as channel numbers.

1 Scaler_Output
2 Discrete_Input
3 Discrete_Output

Hi_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Float
16
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
The status for high alarm and its associated time stamp.

Hi_Bias
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Description:
Float
This bias is added to PSP*Hi_Gain to get Hi_Lim
4
Contained
Static
2
Fieldbus Device
Positive (Initial value is 0.0)

HPM Parameter Reference Dictionary


Honeywell Inc.

513

Hi_Gain

Hi_Gain
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
This gain multiplies the PSP (process actpoint) before addition of biases.
4
Contained
Static
2
Fieldbus Device
(Initial value is 1.1)

Hi_Hi_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Float
16
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
The status for high high alarm and its associated time stamp.

Hi_Hi_Bias
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
2
Fieldbus Device
Positive

Description:
The bias value added to PSP*Hi_Gain to get Hi_Hi_Gain

Hi_Hi_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

514

Description:
Float
The value of the high high alarm trip setting in engineering units.
4
Contained
Static
4
Fieldbus Device
PV_SCALE, +INF

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Hi_Hi_Limx

Hi_Hi_Limx
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Dynamic
1, 3
Fieldbus Device
N/A

Description:
The dynamic calculated Hi_Hi_Lim value.

Float
4
Contained
Dynamic
1, 3
Fieldbus Device

Description:
The dynamic calculated Hi_Lim

Hi_Limx
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Hi_Hi_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Specifies the priority of the high high alarm.

Hi_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Description:
Float
Specifies the value for the high alarm trip setting in engineering units.
4
Contained
Static
4
Fieldbus Device
PV_SCALE, +INF

HPM Parameter Reference Dictionary


Honeywell Inc.

515

Hi_Pri

Hi_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Specifies the priority of the high alarm.

Hysteresis
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

516

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Defines the difference between the switching points.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Ignore

-IIgnore
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Bit String
2
Contained
Dynamic
1, 3
Fieldbus
Device

Range: 0
1
2

Description:
Specifies the inputs to be ignored for the device control function.

Permissive
Interlock
Shutdown

3
4
5

PassiveConfirm
State1Confirm
State2Confirm

Ignore_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Discrete
13
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Generated when a bit in the Ignore word is set

Ignore_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Defines the priority of the Ignore alarm

HPM Parameter Reference Dictionary


Honeywell Inc.

517

Ignore_Time

Ignore_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Defines time (in seconds) allowed to ignore new alarm

In
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
Primary input value of the block. Required for blocks that filter the input to get
the PV.

IN_1 IN_4
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
Auxiliary input value to the block. Used for other values than the PV.

In_Array
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

518

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Array of input or X variables

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

In_D

In_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
Raw confirmation data

In_D1 IN_D16
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Discrete inputs for calculate block

In_Lo
FF Data Type: Value & Status
Floating point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
Defines the value of the transmitter low range. This value is in the same
engineering units as the PV.

Init_Val_1 Init_Val_4
FF Data Type: Value & Status
Floating point
Length: 5
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
Initial value and status of the corresponding interface variable (IV_1 IV_4)

HPM Parameter Reference Dictionary


Honeywell Inc.

519

Init_Val_D1 Init_Val_D4

Init_Val_D1 Init_Val_D4
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
Initial value and status of discrete inputs (IV_D1 IV_D4)

Input_Opts
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Bit String Description:


Defines the options that control the use of auxiliary inputs in the arithmetic.
2
Contained
Static
4
Fieldbus
Device

Range: 0
1
2
3

IN-UseUncertain
IN_LO-UseUncertain
IN_1-UseUncertain
IN_1-UseBad

4
5
6
7

IN_2-UseUncertain
IN_2-UseBad
INJ_3-UseUncertain
IN_3-UseBad

Inst_Err_No
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

520

Unsigned16
2
Contained
Dynamic
4
Fieldbus Device
N/A

Description:
Displays the number of the instruction that sets an error in Calc_Err

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Inst_Ex_Lim

Inst_Ex_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
4
Fieldbus Device
Positive

Description:
Specifies the instruction execution count limit.

Inst_List1
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Defines value of instruction list segment 1.

Bit String
2
Contained
Static
Fieldbus Device
N/A

Integ_Opts
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Bit String Description:


Defines the configuration of the input type and flow direction in the totalizer function.
2
Contained
Static
4
Fieldbus
Device

Range: 0
1
2
3

R610
11/99

Input1Accumulate
Input2Accumulate
FlowForward
FlowReverse

4
5
6

UseUncertain
UseBad
Carry

HPM Parameter Reference Dictionary


Honeywell Inc.

521

Integ_Type

Integ_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Unsigned8 Description:
Determines the direction of counting and type of resetting in the integrator function.
1
Contained
Static
4
Fieldbus
Device

Range: 1
2
3
4

UP_AUTO
UP_DEM
DN_AUTO
DN_DEM

5
6
7

PERIODIC
DEMAND
PER&DEM

Interlock_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Input that duplicates shutdown

Invert_Opts
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Bit String Description:


If the bit is set, the corresponding input or output is inverted (Timer or Discrete Alarm
2
Contained function)
Static
4
Fieldbus
Device

Range: 0
1
2

522

InvertIN_D1
InvertIN_D2
InvertIN_D3

3
4
5

InvertIN_D4
InvertOUT_D
InvertOut_ALM

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

IO_Opts

IO_Opts
FF Data Type: Bit String
Length: 2
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Invert
1
2
3
4

Description:
Option which the user may select to alter input and output block processing.

SP_tracks_PV_if_Man
Reserved
SP_tracks_PV_if_LO
SP_tracks_RCas_or_Cas_if_LO_or_Man

5
6
7
8
9

Increase_to_Close
FaultState_Type
FaultState_Restart
Target_to_Man
PV_for_BkCal_Out

IV_1 IV_4
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Interface variable

IV_D1 IV_D4
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Interface variable

IV_Desc_1 IV_Desc_4
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Description:
Description of interface variables IV_1 IV_4.

Octet String
64
Contained
Static
Fieldbus Device
N/A

HPM Parameter Reference Dictionary


Honeywell Inc.

523

IV_Scale_1 IV_Scale_4

IV_Scale_1 IV_Scale_4
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
2
Fieldbus Device
N/A

Description:
High and low scale values for interface values IV_1 IV_4.

IV_State_1 IV_State_4
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

524

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
Index to the text describing the states discrete interface variables IV_D1IV_D4.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Jog_Time

-JJog_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
2
Fieldbus Device
Positive

Description:
Duration of OUT_D in active state (in seconds); jog open/closed

-LLag_Time
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: positive

Description:
Specifies the lag time constant (in seconds) for the block

Lead_Time
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: positive

R610
11/99

Description:
Specifies the lead time constant (in seconds) applied to input.

HPM Parameter Reference Dictionary


Honeywell Inc.

525

L_Type

L_Type
FF Data Type: Unsigend8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Uninitialized
1

Discrete

Description:
Determines if the values passed by the transducer block to the AI block may be
used directly (Direct) or if the value is in different units and must be converted
linearly(Indirect) , or with square root (Ind Sqr Root), using the input range
defined for the transducer and the associated output range.
2 Indirect
3 Indirect_Sq_Root

Level_Offset
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range

Float
4
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
The distance from the empty calibration level to a reference point, such as the
bottom of the tank.

Lim_Notify
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
2
Fieldbus Device
0-Max_Notify

Description:
Defines the maximum number of unconfirmed alert notify messages allowed.

__Link_Object
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

526

FB Link
8
N/A
Non Volatile
N/A
Fieldbus Device
N/A

Description:
This parameter contains a null set of values that will clear the Link_Object(s) in
a device. This clear value is sent to the device at the start of configuration down
load.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Link_Object

Link_Object
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

FB Link
8
N/A
Non Volatile
N/A
Fieldbus Device
N/A

Description:
Specifies the function block VCR linkage and VCR OD Index and Service
Operation for a block parameter. This parameter is automatically built during
the creation of the LAS Schedule.

LinkScheduleActivationVariable
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Link schedule activation variable.

Lin_Type
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Undefined
1
2
3

R610
11/99

Linear-Input
Linear-Output
SquareRoot

Description:
The linearization type used to describe the behavior of the sensor output.

SquareRootThirdPower
4
SquareRootFifthPower
5
255 Other

HPM Parameter Reference Dictionary


Honeywell Inc.

527

Lo_Alm

Lo_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Float
16
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
The status of the low alarm and its associated time stamp.

Float
4
Contained
Static
2
Fieldbus Device
Positive

Description:
This bias is subtracted from PSP Lo_GainLo_Lim.

Float
4
Contained
Static
2
Fieldbus Device
N/A

Description:
This gain multiplies PSP ( ___ setpoint) before subtraction of biases

Lo_Bias
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Lo_Gain
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Lo_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

528

Description:
Float
Defines the trip setting for the low alarm in engineering units.
4
Contained
Static
4
Fieldbus Device
-INF, PV_SCALE

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Lo_Limx

Lo_Limx
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Dynamic
1, 3
Fieldbus Device
N/A

Description:
The dynamic calculated Lo_Lim.

Lo_Lo_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Float
16
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
The status of the low low alarm and its associated time

Lo_Lo_Bias
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Static
2
Fieldbus Device
Positive

Description:
Specifies the bias is subtracted from PSP*Lo_Gain->Lo_LoLim

HPM Parameter Reference Dictionary


Honeywell Inc.

529

Lo_Lo_Lim

Lo_Lo_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies the trip setting of the low low alarm in engineering units.

Lo_Lo_Limx
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Dynamic
1, 3
Fieldbus Device
N/A

Description:
The dynamic calculated Lo_Lo_Lim.

Lo_Lo_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Defines the priority of the low low alarm.

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Defines the priority of the low alarm.

Lo_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

530

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Lockval

Lockval
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
Defines the flag for holding the first output at the current value.
1
Contained
Static
4
Fieldbus Device
NoLock
1
Lock
2

Low_Cut
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the limit used in square root processing. A value of zero percent-ofscale is used in block processing if the transducer value falls below this limit,
in % of scale. This feature may be used to eliminate noise near zero from a
flow

HPM Parameter Reference Dictionary


Honeywell Inc.

531

Manufac_ID

-MManufac_ID
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
2
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Manufacturer identification number - used by an interface device to locate the
DD file for the resource.

Max_Notify
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the maximum number of possible unconfirmed alert notify messages
possible.

Memory_Size
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

532

Unsigned16
2
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the available configuration memory in the empty resource. This value
is to be checked before attempting a download.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Min_Cycle_T

Min_Cycle_T
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Time duration of the shortest cycle interval of which the resource is capable.

Min_Good
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-4

Description:
Shows the minimum number of good inputs

Mode_Blk
FF Data Type: 4 Bit Strings
Length: 4
Usage: Contained
Storage: Mixed
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0 ROut
1
2
3

RCas
Cas
Auto

Description:
The actual, target, permitted, and normal modes of the block.

4
5
6
7

Man
LO
IMan
OOS

Mode_Blk_AI_Set
FF Data Type: 4 Bit Strings
Length: 4
Usage: Contained
Storage: Mixed
Valid View(s): N/A
Classification: TPSB Only
Range: 3 Auto
4 Man

R610
11/99

Description:
Used by TPSB after configuration download to set the target mode for the AI
Block.

OOS

HPM Parameter Reference Dictionary


Honeywell Inc.

533

Mode_Blk_AO_Set

Mode_Blk_AO_Set
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

4 Bit Strings
4
Contained
Mixed
N/A
TPSB Only
1

Description:
Used by TPSB after configuration download to set the target mode for the AO
Block.

Man

OOS

RCas

Cas

Auto

Mode_Blk_PID_Set
FF Data Type: 4 Bit Strings
Length: 4
Usage: Contained
Storage: Mixed
Valid View(s): N/A
Classification: TPSB Only
Range: 0 ROut
1

RCas

Cas

Auto

Description:
Used by TPSB after configuration download to set the target mode for the PID
Block.

Man

OOS

Mode_Blk_Resource_Set
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

4 Bit Strings
4
Contained
Mixed
N/A
TPSB Only
3

534

Auto

Description:
Used by TPSB after configuration download to set the target mode for the
ResourceBlock.

OOS

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Mode_Blk_AI_OOS

Mode_Blk_AI_OOS
FF Data Type: 4 Bit Strings
Length: 4
Usage: Contained
Storage: Mixed
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 7 OOS

Description:
Used by the TPSB during configuration down load to set the AI block Out of
Service.

Mode_Blk_AO_OOS
FF Data Type: 4 Bit Strings
Length: 4
Usage: Contained
Storage: Mixed
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 7 OOS

Description:
Used by the TPSB during configuration down load to set the AO block Out of
Service.

Mode_Blk_PID_OOS
FF Data Type: 4 Bit Strings
Length: 4
Usage: Contained
Storage: Mixed
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 7 OOS

Description:
Used by the TPSB during configuration down load to set the PID block Out of
Service.

Mode_Blk_Resource_OOS
FF Data Type: 4 Bit Strings
Length: 4
Usage: Contained
Storage: Mixed
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 7 OOS

R610
11/99

Description:
Used by the TPSB during configuration down load to set the Resource block
Out of Service.

HPM Parameter Reference Dictionary


Honeywell Inc.

535

ModelName

ModelName
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
The model name of the instrument. Resides in the VFD

Module_Sn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

536

Visible String
32
Contained
Static
4
Fieldbus Device
N/A

Description:
The serial number of the electronics module in the instrument.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Next_FB_To_Execute

-NNext_FB_To_Execute
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
Specifies the object dictionary index for the block object of a block which will
be invoked to execute following the completion of execution of this block.

N_Reset
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
Displays the number of resets

HPM Parameter Reference Dictionary


Honeywell Inc.

537

N_Start

N_Start
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Dynamic
4
Fieldbus Device
N/A

Description:
Displays the number of false-to-true transitions (combined input).

NodeAddress
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Defines the node address of the fieldbus device on the link

Num_Of_Params
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
The number of parameters associated with the function block including the
block header parameter.

Number_View_3 Number_View_4
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

538

Unsigned8
1
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
Number of entries in the object dictionary for View_3 and View_4 support,
respectively.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

NV_Cycle_T

NV_Cycle_T
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned32
4
Contained
Static
2
Fieldbus Device
N/A

Description:
Interval between writing copies of non-volatile parameters to non-volatile
memory. Zero means never.

HPM Parameter Reference Dictionary


Honeywell Inc.

539

Op_Cmd_CXO

-OOp_Cmd_CXO
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Bit String
2
Contained
Dynamic
3
Fieldbus
Device

Range: 0
1
2

Description:
This command sets the discrete point into the setpoint state.

Reserved
Close
Open

3
4

Stop
Enable-1-2-3

Op_Cmd_Int
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Unsigned8 Description:
This command rests the integrator.
1
Contained
Dynamic
1, 3
Fieldbus
Device
Range: 0
OFF
1
RESET

Op_Cmd_Spg
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Unsigned8
1
Contained
Dynamic
1, 3
Fieldbus
Device

Range: 0
1

540

Description:
This operator commend enables the positions in a profile in the setpoint ramp.

UNDEFINED
RESET_IN

2
3

ADVANCED
REPEAT

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Op_Select

Op_Select
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Specifies an operator settable param to force a given input

Out
FF Data Type: Value & Status Description:
Floating Point
The primary analog value calculated as a result of executing the function block.
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: Out_Scale +/- 10%

Out_1 Out_2
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Defines the block outputs required by splitter.

Out_1_State Out_4_State
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
Units code for discrete output 1

HPM Parameter Reference Dictionary


Honeywell Inc.

541

Out_1_Units Out_4_Units

Out_1_Units Out_4_Units
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
Defines the engineering units code for discrete outputs 1-4.

Out_Accum
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Specifies the number of accumulated counts.

Out_Alm
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
The alarm summary variable of the analog block

Out_Alm_Sum
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

542

Unsigned8
1
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies the alarm conditions for a true Out_Alm in the analog alarm.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Out_Array

Out_Array
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Array of output or Y variables

Out_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: Out_State

Description:
The primary discrete value calculated as a result of executing the function
block.

Out_D1 Out_D4
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
The calculated discrete output value for this block

Out_Exp
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
Specifies the time expired. Stops at Timer_SP

HPM Parameter Reference Dictionary


Honeywell Inc.

543

Out_Hi_Lim

Out_Hi_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
Defines the maximum output hi limit value for modes other than Manual.
4
Contained
Static
2
Fieldbus Device
OUT_SCALE +/- 10%

Out_Lo_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
Defines the minimum output limit value for modes other than Manual.
4
Contained
Static
2
Fieldbus Device
OUT_SCALE +/- 10%

Out_Ptrip
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0
OFF
ON
1

Description:
Defines the state and value of the second discrete output.

Out_Rem
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

544

Description:
Specifies the time remaining if the timer is active

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Out_Scale

Out_Scale
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
2
Fieldbus Device
N/A

Description:
Defines the high and low scale values, engineering units code, and number of
digits to the right of the decimal point to be used in displaying the Out
parameter and parameters which have the same scaling as Out.

Out_State
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
Specifies the index number to the text describing the state of a discrete output.

Out_Trip
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0
Off
On
1

Description:
Specifies the alarm trip state of the first discrete output

Out_Units
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
Defines the engineering units that are to be displayed for the output.

HPM Parameter Reference Dictionary


Honeywell Inc.

545

Outage_Lim

Outage_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

546

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Defines the maximum tolerated duration for power failure

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Pause

-PPause
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
This command stops the timer when the command is set to true

Pause_Cause
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Unsigned8 Description:
Specifies the cause of a pause.
1
Contained
Dynamic
1, 3
Fieldbus
Device

Range: 0
1
2
3

NotPaused
OperatorPause
LogicPause
DeviationPause

4
5
6
7

Operator&Logic
Operator&Deviation
Logic&Deviation
Operator&Logic&Deviation

Pct_Incl
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Dynamic
1, 3
Fieldbus Device
N/A

Description:
Displays the percentage of inputs with good static's

HPM Parameter Reference Dictionary


Honeywell Inc.

547

PDTag

PDTag
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Defines the physical device tag

Permissive_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Specifies the input that prevents Out_D from going to the active state

Pre_Out
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Displays the output value and status.

Pre_Out_1 Pre_Out_2
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

548

Description:
Displays output value and status of pre-output 1 and 2

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Pre_Out_Alm

Pre_Out_Alm
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Specifies the alarm summary variable of an analog alarm block

Pre_Out_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Specifies the alarm summary variable of a discrete.

Pre_Out_D1 Pre_Out_D4
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Specifies the alarm summary variable calculated discrete variables 1-4

Pre_Trip
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Static
4
Fieldbus Device
positive

Description:
Adjusts the quantity that will set Out_Ptrip

HPM Parameter Reference Dictionary


Honeywell Inc.

549

Primary_Value

Primary_Value
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
The measured value and status available to the function block.

Primary_Value_Range
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
2, 4
Fieldbus Device
N/A

Description:
The High and Low range limit values, the engineering units code, and the
number of digits to the right of the decimal point to be used to display the
primary value.

Primary_Value_Type
FF Data Type: Unsigned16
Length: 2
Usage: Contained
Storage: Static
Valid View(s): 2, 4
Classification: Fieldbus Device
Other
Range: 1
100
101
102
103

Description:
The type of measurement represented by the primary value. For example: Mass
Flow, Absolute Pressure, Differential Temperature.

MassFlow
VolumetricFlow
AverageMassFlow
AverageVolumetricFlow

104
105
106
107
108

ProcessTemperature
Non-ProcessTemperature
DifferentialTemperature
DifferentialPressure
GaugePressure

109
110
111
112
113

AbsolutePressure
Level
pH (picohenry)
mV (millivolt)
Conductivity

PROFILE
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

550

Unsigned16
2
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
Number assigned by the FOUNDATION Fieldbus which uniquely identifies
the profile on which the block definition is based

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Profile_Revision

Profile_Revision
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
The revision number of the profile on which the block definition is based.

Prop_Lims
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 = False

Description:
Defines whether the limits are propogated to the result

1 = True

PSP
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Specifies the value of the process setpoint

Pulse_Dur
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies the pulsewidth, in seconds, of the integral pulse

HPM Parameter Reference Dictionary


Honeywell Inc.

551

Pulse_Val and Pulse_Val1 Pulse_Val2

Pulse_Val and Pulse_Val1 Pulse_Val2


FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
positive

Description:
The value of each metered pulse in engineering units.

PV
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
The primary analog value for use in executing the function, or a process value
associated with the function. May also be calculated from the READBACK
value of an AO block.

PV_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Defines the primary discrete value for use in executing the function, or a
process value associated with it. May also be calculated from the Readback_D
parameter value of a digital output.

PV_Ftime
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

552

Float
4
Contained
Static
4
Fieldbus Device
positive

Description:
Specifies the time constant (in seconds) of a single exponential filter for the
PV.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

PV_Scale

PV_Scale
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
2
Fieldbus Device
N/A

Description:
Defines the high and low scale values, engineering units code, and number of
digits to the right of the decimal point to be used in displaying the PV
parameter and parameters which have the same scaling as PV.

PV_State
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
This parameter contains the index umber of the text describing the state of a
discrete PV within the object dictionary.

PV_Units
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned16
2
Contained
Static
2
Fieldbus Device
See Units

Description:
Defines the engineering units index for the units that are to be dislayed.

HPM Parameter Reference Dictionary


Honeywell Inc.

553

Quies_Opt

-QQuies_Opt
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Unsigned8
2
Contained
Static
4
Fieldbus
Device

Range: 0
1
2

554

Description:
Options for Out_Exp and Out_Rem during quiescence

Uninitialized
Clear
Last

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

RA_Ftime

-RRA_Ftime
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the time constant (in seconds) of a single exponential filter for the
value to be ratioed..

Range_Hi
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the value of the constant used in switching to HI Range.

Range_Lo
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the value of the constant used in switching to LO Range.

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the derivative time constant in seconds.

Rate
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

555

RCas_In

RCas_In
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Non-Volatile
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
The target setpoint and status provided by a supervisory host to a analog
control or output block.

RCas_In_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Non-Volatile
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
The target setpoint and status provided by a supervisory host to a discrete
control or output block.

RCas_Out
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
The block setpoint and status after ramping - provided to a supervisory host for
back calculation and to allow action to be taken under limiting conditions or
mode change.

RCas_Out_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

556

Description:
The block setpoint and status provided to a supervisory host for back
calculation and to allow action to be taken under limiting conditions or mode
change.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

ReadBack

ReadBack
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Indicates the readback value of the actual continuous valve or other actuator
position, in transducer units.

ReadBack_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Indicates the readback state of the actual discrete valve or other actuator
position, in the transducer state.

Release
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Visible String
32
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Manufacturer release information. Resides in the VFD

HPM Parameter Reference Dictionary


Honeywell Inc.

557

Reset

Reset
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
positive, +INF

Description:
Defines the integral time constant (in seconds) per repeat.

Reset_Confirm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
Momentary discrete value which must be written by a host device to enable
1
further resets.
Contained
Dynamic
3
Fieldbus Device
Off
0
Confirm
1

Reset_D
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Dynamic
3
Fieldbus Device
Off
0
Reset
1

Description:
Momentary switch that clears the locked out condition or retries the faile state.

Reset_In
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0
Off
Reset
1

558

Description:
This command resets the timer

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Restart

Restart
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Dynamic
Valid View(s): N/A
Classification: Fieldbus Device
Range: 0 Uninitialized

Description:
Allows a manual restart to be initiated. Several degrees of restart are possible..

1 Run
2 Restart Resource

Restart with Defaults

Restart Processor

Restart_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies the maximum time required in the passive state.

Rev_Flow1 Rev_Flow2
FF Data Type: Value & Status Description:
Discrete
Indicates reverse flow when true
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0
FORWARD
REVERSE
1

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

559

ROut_In

ROut_In
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Non-Volatile
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
The target output and status provided by a host to the control block for use as
the output (ROut mode).

ROut_Out
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 3
Classification: Fieldbus Device
Range: N/A

Description:
The block output and status provided to a host for back calculation in ROut
mode and to allow action to be taken under limited conditions or mode change.

RS_State
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0 Uninitialized
1
2
3

StartRestart
Initialization
Online_Linking

Description:
The current state of the function block application-state machine.

4
6
5

Online
Failure
Standby

Rtotal
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

560

Float
4
Contained
Non-Volatile
1, 3
Fieldbus Device
N/A

Description:
Specifies the total number non-good statuses.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Safeguard_Cl

-SSafeguard_Cl
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
Defines the high-priority discrete setpoint

Safeguard_Op
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
Defines the high-priority discrete output.

SchName
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Visible String
32
N/A
N/A
N/A
TPSB Only
N/A

Description:
Defines the strategy name for the LAS Schedule.

HPM Parameter Reference Dictionary


Honeywell Inc.

561

Secondary_Value

Secondary_Value
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
The secondary value related to the sensor.

Secondary_Value_Unit
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned16
The engineering units to be used with Secondary_Value parameter value.
2
Contained
Static
2
Fieldbus Device
(see Appendix for UNITS values)

Sel_1 Sel_3
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Input value to the respective selector input (1-3).

Sel_Type
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Uninitialized
1

562

High

Description:
This parameter specifies the type of selector action.

2
3

Low
Middle

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Select_Type

Select_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:

Unsigned8 Description:
This parameter specifies the selector action type.
1
Contained
Static
4
Fieldbus
Device

Range: 0
1
2

Uninitialized
FirstGood
Min

3
4
5

Max
Mid
Avg

Selected
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
Integer indicating which input is selected

Sensor_Cal_Date
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Date
7
Contained
Static
4
Fieldbus Device
N/A

Description:
The date of the last sensor calibration.

Sensor_Cal_Loc
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Visible String
32
Contained
Static
4
Fieldbus Device
N/A

Description:
The last physical location at which the sensor was calibrated. (ex. Acme Labs)

HPM Parameter Reference Dictionary


Honeywell Inc.

563

Sensor_Cal_Method

Sensor_Cal_Method
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 100 Volumetric
101
102
103

Description:
The method of last sensor calibration. It could be one of the several standard
calibration methods defined by ISO or some other method.

StaticWeight
DynamicWeight
FactorTrimStandard

104
105
106
255

UserTrimStandard
FactoryTrimSpecial
UserTrimSpecial
Other

Sensor_Cal_Who
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
Contained
Static
N/A
Fieldbus Device
N/A

Description:
The name of the person responsible for the last sensor calibration.

Sensor_Connection
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
The number of wires for the temperature probe.
1
Contained
Static
4
Fieldbus Device
2_wire
2
3_wire
3
4_wire
4

Sensor_Fill_Fluid
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

564

Unsigned16
2
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the type of fluid used in the sensor.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Sensor_Isolator_Mtl

Sensor_Isolator_Mtl
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the construction material of the isolator

Sensor_Offset
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
The distance from the sensor reference point to the top of the tank.

Sensor_Range
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
4
Fieldbus Device
N/A

Description:
The High and Low range limit values, the engineering units code and the
number of digits to the right of the decimal point for the sensor.

Sensor_Sn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Visible String
4
Contained
Static
4
Fieldbus Device
N/A

Description:
The sensor serial number.

HPM Parameter Reference Dictionary


Honeywell Inc.

565

Sensor_Type

Sensor_Type
FF Data Type: Unsigned16
Description:
Defines the sensor type.
Length: 2
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Non-Standard
Range: -1
100
101
102
103
105
104
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121

FlowSensorUnknown
Coriolis(Gyroscopic)
Electromagnetic
mV (millivolt)
DeltaOhm
Ohm
NuclearMagneticResonance
PositiveDisplacement
Refraction
Tagging
Ultrasonic(Doppler)
Ultrasonic(TimeOfTravel)
Vortex
Target
VariableArea
LevelSensorUnknown
Radar
Capacitance
Nuclear
Ultrasonic
FloatGauge
PressureSensorUnknown

122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144

ResonantWire
VibrationBeam
StrainGague
PiezoResistive
SiliconResonant
TemperatureSensorUnknown
PT100_A_385
PT100_A_392
PT200_A_385
PT500_A_385
NI120
CU10
T/C-Type_B
T/C-Type_C
T/C-Type_E
T/C-Type_J
T/C-Type_K
T/C-Type_N
T/C-Type_R
T/C-Type_S
T/C-Type_T
T/C-Type-DIN_L
T/C-Type-DIN_U

SequenceName
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

566

Visible String
32
N/A
N/A
N/A
TPSB Only
N/A

Description:
Defines the strategy name for a sequence in the LAS Schedule

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Servo_Gain

Servo_Gain
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the servo PID gain value.

Servo_Rate
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the servo PID rate value.

Servo_Reset
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Defines the servo PID reset value.

Set_Fstate
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Dynamic
Valid View(s): N/A
Classification: Fieldbus Device
Range: 0 Uninitialized

Description:
Allows the failsafe condition to be manually initiated by selecting Set.

1 Off
2 Set

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

567

Shed_Opt

Shed_Opt
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Uninitialized
1
2
3
4

Description:
Defines the shed option for the remote control device.

NormalShed_NormalReturn
NormalShed_NoReturn
ShedToAuto_NormalReturn

ShedToManual_NormalReturn

6
7

ShedToManual_NoReturn

ShedToRetainTarget_NormalReturn
ShedToRetainTarget_NoReturn

ShedToAuto_NoReturn

Shed_Rcas
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned32
4
Contained
Static
2
Fieldbus Device
N/A

Description:
Function block will shed from Rcas to the specified shed option if a write
command has not been received within this time duration.

Shed_Rout
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

568

Unsigned32
4
Contained
Static
2
Fieldbus Device
N/A

Description:
Function block will shed from Rout to the specified shed option if a write
command has not been received within this time duration.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Shutdown_D

Shutdown_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: 0
Off
On
1

Description:
Specified the input that causes Out_D to go to the passive state

Simulate
FF Data Type: Simulate Floating Point
Length: 11
Usage: Contained
Storage: Dynamic
Valid View(s): N/A
Classification: Fieldbus Device
Range: N/A

Description:
Allows manually-entered value for transducer analog I/O.

Simulate_D
FF Data Type: Simulate Discrete
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): N/A
Classification: Fieldbus Device
Range: N/A

Description:
Allows manually-entered value for transducer discrete I/O.

Simulate_P
FF Data Type: Simulate Floating Point
Length: 11
Usage: Contained
Storage: Dynamic
Valid View(s): N/A
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
Allows manually-entered value for transducer.

HPM Parameter Reference Dictionary


Honeywell Inc.

569

Simulate_S

Simulate_S
FF Data Type: Simulate Discrete
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): N/A
Classification: Fieldbus Device
Range: N/A

Description:
Allows manually-entered value for transducer strings (PSEUDO)

SP
FF Data Type: Value & Status Description:
Floating Point
The analog setpoint value of this block.
Length: 5
Usage: Contained
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: PV_SCALE +/- 10%

SP_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: PV_State

Description:
The discrete setpoint value of this block.

Spg_State
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Dynamic
Valid View(s): 1, 3
Classification: Fieldbus Device
Undefined
Range: 0
1
2

570

Ready
Active

Description:
Defines the operating state of the block in the setpoint ramp function

3
4

Pause
AT_End

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

SP_Hi_Lim

SP_Hi_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
Defines the setpoint high limit. The setpoint high limit is the highest setpoint
4
operator entry that can be used for the block.
Contained
Static
2
Fieldbus Device
PV_SCALE +/- 10%

SP_Lo_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Float
Defines the setpoint low limit. The setpoint low limit is the lowest setpoint
4
operator entry that can be used for the block.
Contained
Static
2
Fieldbus Device
PV_SCALE +/- 10%

SP_Rate_Dn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive, +INF

Description:
Defines the ramp rate at which downward setpoint changes are acted on in
Auto mode, in PV units per second. If the ramp rate is set to zero or the block is
in a mode other than Auto, then the setpoint will be used immediately.

SP_Rate_Up
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Static
4
Fieldbus Device
positive, +INF

Description:
Ramp rate at which upward setpoint changes are acted on in Auto mode, in PV
units per second. If the ramp rate is set to zero or the block is in a mode other
than Auto, then the setpoint will be used immediately.

HPM Parameter Reference Dictionary


Honeywell Inc.

571

SRTotal

SRTotal
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
This parameter contains the snapshot of the Rtotal value just before reset

Float
4
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
The parameter contains the snapshot value of the setpoint.

Unsigned16
2
Contained
Static
1, 2, 3, 4
Fieldbus Device
N/A

Description:
This parameter contains the revision level of the static data associated with the
function block. The revision value will be incremented each time a static
parameter value in the block is changed.

SSP
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

ST_Rev
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Start
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

572

Description:
A leading edge at this input

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Start_Type

Start_Type
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Uninitialized
1

Description:
Specifies the starting point option in the setpoint ramp function.

2
3

UseCurve

UseDuration
UseRate

Start_Val
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
2
Fieldbus Device
N/A

Description:
Specified the starting point of each segment of the setpoint profile

Status_Opts
Description:
FF Data Type: Bit String
Options which the user may select in the block processing of status. Status
Length: 2
options are applicable to the following blocks: BG, PD, AI, DI, AO, ML, CS,
Usage: Contained
RA, PID, and DO
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
5 Target_to_Man_if_Bad_IN
Range: 0 IFS_if_Bad_IN
1
2
3
4

IFS_if_Bad_Cas_IN
Uncertain_as_Good
Propogate_Fault_Fwd
Propogate_Fault_Bkwd

6 Uncertain_if_Limited
7 Bad_if_Limited
9 Reserved

Step_Posn
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
This parameter specifies the current step

HPM Parameter Reference Dictionary


Honeywell Inc.

573

Stotal

Stotal
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
This parameter contains a snapshot of the total value before a reset occurs.

Unsigned16
2
Contained
Static
4
Fieldbus Device
N/A

Description:
The strategy field can be used to identify grouping of blocks.

Strategy
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

SubSchName
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
TPSB Only
N/A

Description:
Defines the strategy name of a sub-schedule in the LAS Schedule.

Swap_2
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

574

Description:
Unsigned8
This parameter swaps In_2 to Y and Out_2 to X
1
Contained
Static
4
Fieldbus Device
NoSwap
1
Swap
2

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Tag_Desc

-TTag_Desc
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Octet String
32
Contained
Static
N/A
Fieldbus Device
N/A

Description:
The user description of the block

Temp_1 Temp_4
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Contained
Storage: Dynamic
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
The parameter defines the temperatur setpoints.

Temp_D1 Temp_D8
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Contained
Storage: Dynamic
Valid View(s): 4
Classification: Fieldbus Device
Range: N/A

Description:
Defines the discrete variable for temperature

Test_RW
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Test
112
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Specifies the read/write test parameter.

HPM Parameter Reference Dictionary


Honeywell Inc.

575

Time_Posn

Time_Posn
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
This parameter determines the current step

Time_Posn_T
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Output
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
This parameter determines the current step

Time_Unit1 Time_Unit2
FF Data Type: Unsigned8
Description:
These parameters specify the units of time for display in the pulse input,
Length: 1
setpoint ramp, and timer functions.
Usage: Contained
Storage: Static
Valid View(s): 2
Classification: Fieldbus Device
3
Uninitialized
Minutes
Range: 0
1
2

Seconds
Hours

4
5

Days
[day-[hr:[min[:sec]]]]

Time_Units
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Uninitialized
1
2

576

Seconds
Hours

Description:
This parameter displays the time units for Timer_SP,Out_Exp,& Out_Rem

3
4
5

Minutes
Days
[day-[hr:[min[:sec]]]]

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Total_Sp

Total_Sp
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
1, 3
Fieldbus Device
Positive

Description:
The SP for batch totalization

Timer_Type
FF Data Type: Unsigned8
Length: 1
Usage: Contained
Storage: Static
Valid View(s): 4
Classification: Fieldbus Device
Range: 0 Measure
1
2
3

Accum
Compare
Delay

Description:
Defines the type of time processing applied to the PV in the timer function.

4
5
6
7

Extend
Debounce
Pulse
RT_Pulse

Travel_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Specifies the required time for the actuator to move final control from a to b

Travel_Timer
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Float
4
Contained
Dynamic
4
Fieldbus Device
N/A

Description:
Displays the time taken to confirm a new state

HPM Parameter Reference Dictionary


Honeywell Inc.

577

Transducer_Directory

Transducer_Directory
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Non-Volatile
N/A
Fieldbus Device
N/A

Description:
A directory that specifies the number and starting indices of the data collections
in the transducer block.

Transducer_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned16
Identifies the transducer type as shown in the following listing.
2
Contained
Non-Volatile
1, 2, 3, 4
Fieldbus Device
Other
1
104 Flow-Calibrated
100 Pressure-Calibrated
105 BasicPositonerValve
101 Temperature-Calibrated
106 AdvancedPositionerValve
DualTemperature-Calibrated
102
107 DiscreteValve
103 RadarLevel-Calibrated

Trip_Time
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

578

Float
4
Contained
Static
4
Fieldbus Device
Positive

Description:
Specifies the amount of time before the alarm enters the tripped condition.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Trk_In_D

Trk_In_D
FF Data Type: Value & Status
Discrete
Length: 2
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

Description:
This discrete input is used to initiate external tracking of the block output to the
value specified by TRL_VAL.

Trk_Scale
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
4
Fieldbus Device
N/A

Description:
The high and low scale values, engineering units code, and number of digits to
the right of the decimal point associated with TRK_VAL

Trk_Val
FF Data Type: Value & Status
Floating Point
Length: 5
Usage: Input
Storage: Non-Volatile
Valid View(s): 1, 3
Classification: Fieldbus Device
Range: N/A

R610
11/99

Description:
This input is used as the track value when external tracking is enabled by
TRK_IN_D.

HPM Parameter Reference Dictionary


Honeywell Inc.

579

Uncert_Lim

-UUncert_Lim
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
0-100

Description:
Defines the limit for Pct_Incl.

Unit_Conv
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Float
4
Contained
Static
4
Fieldbus Device
N/A

Description:
Specifies the factor to be used to convert the engineering units of Input 1 to
engineering units of Input 2.

Update_Evt
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

580

Event Update
14
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
Specifies the event that caused the update.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Valve_Man_Id

-VValve_Man_Id
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
The valve manufacturer's identification number as defined by the
FOUNDATION Fieldbus.

Valve_Model_Num
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
The valve model number as defined by the valve manufacturer.

Valve_Sn
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
Contained
Non-Volatile
4
Fieldbus Device
N/A

Description:
The valve serial number defined by the valve manufacturer..

Valve_Type
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned8
1
Contained
Static
4b
Fieldbus Device
Undefined
0
Linear
1

Description:
The type of valve as defined in FOUNDATION Fieldbus Transducer
Specifications (FF-903)..

2
255

Rotary
Other

HPM Parameter Reference Dictionary


Honeywell Inc.

581

Velocity_Unit

Velocity_Unit
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned16
The units code index for the engineering unit descriptor for the propagation
2
velocity.
Contained
Static
4
Fieldbus Device
Refer to the Appendix.

VendorName
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Defines the vendor or manufacturer name. Resides in The VFD

Unsigned16
2
N/A
N/A
N/A
TPSB Only
N/A

Description:
Specifies the relative index of the virtual field device in the
VFD_REF_ENTRY list.

Visible String
32
N/A
N/A
N/A
Fieldbus Device
N/A

Description:
Specifies the tag name for the virtual field device.

Vfd
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

VfdTag
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

582

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

VIEWS_INDEX

VIEWS_INDEX
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned16
2
Contained
N/A
N/A
Fieldbus Device
N/A

Description:
Specifies the object dictionary index for VIEW_1. Block views are listed
contiguously in the object dictionary starting with VIEW_1.

HPM Parameter Reference Dictionary


Honeywell Inc.

583

Write_Alm

-WWrite_Alm
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Alarm Discrete
13
Contained
Dynamic
N/A
Fieldbus Device
N/A

Description:
This alert is generated if an attempt is made to write to a parameer that has
been write-locked.

Write_Lock
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Description:
Unsigned8
If set, no writes from anywhere are allowed, except to clear WRITE_LOCK.
1
Block inputs will continue to be updated.
Contained
Static
2
Fieldbus Device
0 Uninitialized
1 Not_Locked
2 Locked

Write_Pri
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

584

Unsigned8
1
Contained
Static
4
Fieldbus Device
0-15

Description:
Priority of the alarm generated by clearing the write lock.

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Xd_Cal_Date

-XXd_Cal_Date
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Date
7
Contained
Static
4c
Fieldbus Device
N/A

Description:
Displays the date of the last calibration on the transducer block.

Xd_Cal_Loc
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Visible String
32
Contained
Static
4c
Fieldbus Device
N/A

Description:
The physical location at which the last calibration was performed. (ex. NIST,
AcmeLabs).

Xd_Cal_Who
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Visible String
32
Contained
Static
4c
Fieldbus Device
N/A

Description:
Specifies the name of the person responsible for the last positioner calibration.

HPM Parameter Reference Dictionary


Honeywell Inc.

585

XD_Error

XD_Error
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned8
1
Contained
Dynamic
1, 3
Fieldbus Device
0
1
2
3
4
5
6
7
8
9
10
11
12

Description:
Transducer error code as defined in the FOUNDATION Fieldbus Transducer
Specifications (Block Alarm Subcodes)..

Other
BlockConfiguration
LinkConfiguration
SimulationActive
LocalOverride
DeviceFaultState
DeviceMaintenance
InputFailure
OutputFailure
MemoryFailure
LostStaticData
LostNVData
ReadbackCheck

13
14
15
16
17
18
19
20
21
22
23
24
25

MaintenanceNeeded
PowerUp
OutOfService
UnspecifiedError
GeneralError
CalibrationError
ConfigurationError
ElectronicsFailure
MechanicalFailure
I/Ofailure
DataIntegrityError
SoftwareError
AlgorithmError

XD_Scale
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Scaling
11
Contained
Static
2
Fieldbus Device
N/A

Description:
Defines the transducers high and low scale values, engineering units code, and
number of digits to the right of the decimal point used for the value obtained
from the transducer.

XD_State
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

586

Unsigned16
2
Contained
Static
2
Fieldbus Device
11
31
67
71

Description:
Defines the index to the text describing the states of a discrete transducer.

Bad::NotConnected:Constant
Bad::OutOfService:Constant
Uncertain::NonSpecific:Constant
Uncertain::LastUsableValue: Constant

75
79
131

Uncertain::SubstituteValue: Constant
Uncertain::InitialValue: Constant
Good_NonCascade::Non Specific:Constant

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

X_Units

X_Units
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
Defines the variables engineering units x-axis when the variable sis to be
displayed in a graph.

-YY_Units
FF Data Type:
Length:
Usage:
Storage:
Valid View(s):
Classification:
Range:

R610
11/99

Unsigned16
2
Contained
Static
2
Fieldbus Device
N/A

Description:
Defines the variables y-axis engineering units when the variable is to be
displayed in a graph.

HPM Parameter Reference Dictionary


Honeywell Inc.

587

Y_Units

588

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

APPENDIX A ENUMERATIONS
This appendix contains the enumerations of the parameters described in the previous listing of fieldbus
parameters.
Table 3 Enumeration Description and Value

Enumeration

Description

ACCEPT_D
0 Off
1 Accept

Accept_D, PV copy of output switch.

ALERTORD
Order of alerts for Alarm_Sum and Ack_Option. (Is one of the structured Params said John)
0 FailAlarm
5
Reserved
1 Reserved
6
Reserved
2 Reserved
7
BlockAlarm
3 reserved
8
AcceptAlarm
4 Reserved
9
IgnoreAlarm
ALMSTATE
0
1
2

Alarm State, A discrete enumeration which gives an indication of whether the alert is active and
whether it has been activated.
Uninitialized
3 Active_Reported
Clear Reported
4 Active-Not_Reported
Clear Not_Reported

ARITHTYP
Arith_Type, The algorithm types for the Arithmetic Function.
1 FlowCompensationLinear
6 Average
2 FlowCompensationSQRoot
7 Summer
3 FlowCompensationAppx
8 ForthOrderPoly
4 BTUFlow
9 HTGCompensatedLevel
5 MultiplyDivide
AUTH_PDU
0
1

FasArTypeAndRole DLPDU.

Ordinary
Authentication

2
3

Source
Maximal

CALCERRS
Calc_Errrs, Calculation errors indications for the Calculate function.
0 Non-SpecificError
7 IllegalOperator
1 DivideByZero
8 JMP-OutOfList
2 Overflow
9 InvalidDataType
3 FunctionError
10 TypeConversionFailed
4 FunctionCallNotSupported
11 ST-Disallowed
5 FuntionCallArgumentCount
12 StackOverflow
6 FunctionCallArgumentType
13 INST_EX_LIM-Count
CHEKBACK
CheckBack, The actual status of the final control element in complex AO and DO.
0 Stat_Safeguard_OP
8 Stat_Rb_D_CL
1 Stat_Safeguard_CL
9 Stat_Torque_D_OP
2 Stat_Binary_OP
10 Stat_Torque_D_CL
3 Stat_Binary_CL
11 Stat_Sub_Mode
4 Stat_Disc
12 Stat_Trav_Time
5 Stat_Disc_D_Op
13 Reserved1
6 Stat_Disc_D_CL
14 Reserved2
7 Stat_Rb_D_OP

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

589

Appendix A Enumerations

Enumeration

Description

COMBTYPE
Comb_Type, Determines how the multiple IN_D values are combined in the Timer function.
0 AND
22 EXACTLY2
1 OR
23 EXACTLY3
2 ANY2
40 EVEN
3 ANY3
41 ODD
21 EXACTLY1
CONDTYPE
0
None
1
Delay
2
Extend

Cond_Type, The type of conditioning applied to PV_D in the Discrete Alarm function.
3
Debounce
4
Pulse
5
RT_Pulse

CONSUMER
0
NotConf
1
Local

Pseudo linkage type for the consuming input parameter.


2
Subscriber
3
Client

CURRSUM
Current, The active status of each alarm.
0
Discrete_Alarm
4
1
HiHi_Alarm
5
2
Hi_Alarm
6
3
LoLo_Alarm
7

Lo_Alarm
DevHi_Alarm
DevLo_Alarm
Block_Alarm

DATADELV
FasDLSDAP - DLCEP Data Delivery Feature.
0
Unordered
2
Disordered
1
Ordered
3
Classical
DC_STATE
DC_State, Device Control State represents the current state of the device.
0
ConfirmedPassive
7
FailedState_1
1
ConfirmedState_1
8
FailedState_2
2
ConfirmedState_2
9
Tripped
3
GoingToPassive
10
LostInterlock
4
GoingToState_1
11
Locked
5
GoingToState_2
12
LostMCCPower
6
FailedPassive
DEVCLASS
Device Class DLOpertatFunctionalClass.
0
UNDEFINDED
2
LINKMASTER
1
BASIC
3
BRIDGE
DEVOPTS
Device_Opts, Options used in processing the Device Control function.
0
Interlock
4
Trip
1
TrackSPInLO
5
LostPower
2
Permissive
6
PassiveWhenConfigured
3
ResetRequired
7
BusRestartPassive
DISABLEX
0
Use
1

Disable(I), The disable or use input switch for the Input Selector function.

Disable

DISBLSUM
Disabled, The disabled state of each.
0
Disc_Alm_Disabled
4
1
HiHi_Alm_Disabled
5
2
Hi_Alm_Disabled
6
3
LoLo_Alm_Disabled
7

590

Lo_Alm_Disabled
DevHi_Alm_Disabled
DevLo_Alm_Disabled
Block_Alm_Disabled

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Appendix A Enumerations

Enum Name

Description

DISCCOND

Disc_Cond, Defines the condition in OUT_D that will generate an alarm in the Discrete Alarm
function.
2
TRUE
3
Change

0
1

None
FALSE

DLLSDAP
FasDllSDAP - Schedule, Delivery, Authenication, Priority.
0
NotConfig
43
QUB:Acyclic,Disordered,Source,Time
1
QUU:Acyclic,NA,Source,Urgent
59
QUB:Acyclic,Clasical,Source,TimeAvai
3
QUU:Acyclic,NA,Source,TimeAvail
137
BNU:Cyclic,Unordered,Source,Urgent
41
QUB:Acyclic,Disordered,Source,Urgent
153
BNU:Cyclic,Ordered,Source,Urgent
42
QUB:Acyclic,Disordered,Source,Norm
DLLTIMEC
FasDllTimelinessClass - NotConfig or Duplicate Detection.
0
NotConfig
8

BNU:DuplicateDetection

ENBLDSBL
Enable Disable,
0
Uninitialized
1
Disabled
FAIL
1
2
3
4
5
6

Active

Fail, Enumeration of the current failure conditions in the Device Control.


PassiveConfirmTime
7
Tripped
State_1ConfirmTime
8
LostInterlock
State_2ConfirmTime
9
LockedOut
PassiveConfirmLost
10
LostPower
State_1ConfirmLost
11
MultipleConfirms
State_2ConfirmLost

FEATSUPR
FmsFeaturesSupported - FMS Services for VCR.
0
GetOD l
14
PhysRead
1
UnsolicitedStatus
15
PhysWrite
2
PutOD
16
InformationReport
3
DownLoad
17
InformationReportWithType
4
UpLoad
18
VariableList
5
RequestDomainDownLoad
19
EventNotification
6
RequestDomainUpload
20
EventNotificationWithType
7
ProgamInvocation
21
AcknowledgeEventNotification
8
StartStopResumeReset
22
AlterEventConditionMonitoring
9
Kil
23
AddressingWithName
10
Read
24
GenericInitateDownloadSequence
11
Write
25
GenericDownloadSegment
12
ReadWithType
26
GenericTerminateDownloadSequence
13
WriteWithType
FMSBYPAS
FasArTypeAndRole , FMS Bypass Switch.
0
NOBYPASS
1
BYPASS
FORWREVS
0
Forward
1
Reverse

Rev_Flow_n, Reverse flow indications in the Integrator function.

IGNORE
Ignore, Inputs to ignore for the Device Control function.
0
Permissive
3
PassiveConfirm
1
Interlock
4
State1Confirm
2
Shutdown
5
State2Confirm

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

591

Appendix A Enumerations

Enumeration

Description

INPUTOPT
Input_Opts, Options that control the use of auxiliary inputs in the Arithmetic.
0
IN-UseUncertain
4
IN_2-UseUncertain
1
IN_LO-UseUncertain
5
IN_2-UseBad
2
IN_1-UseUncertain
6
IN_3-UseUncertain
3
IN_1-UseBad
7
IN_3-UseBad
INTEGOPT
Integ_Opts, The configuration of the input type and flow direction in the Totalizer function.
0
Input1Accumulate
4
UseUncertain
1
Input2Accumulate
5
UseBad
2
FlowForward
6
Carry
3
FlowReverse
INTEGTYP
Integ_Type, Determines the direction of counting and type of resetting in the Integrator function.
1
UP_AUTO
5
PERIODIC
2
UP_DEM
6
DEMAND
3
DN_AUTO
7
PER&DEM
4
DN_DEM
INVRTOPT
0
1
2

Invert_Opts, If the bit is set the corresponding input


or output is inverted (Timer or
Discrete Alarm function).
InvertIN_D1
3
InvertIN_D4
InvertIN_D2
4
InvertOUT_D
InvertIN_D3
5
InvertOut_ALM

MESGTYPE
0
1

Undefined
EventNotification

OFFRESET
0
Off
1

MessageType - Message Type for Alerts.


2
3

AlarmClear
AlarmOccur

Reset_D, Reset_In, The off = 0 and reset = 1 state.

Reset

OPCMDCXO
OP_CMD_CXO, Operator discrete setpoint for complex AO, DO.
0
Reserved
3
Stop
1
Close
4
Enable-1-2-3
2
Open
OPCMDINT
Op_Cmd_Int, Operator Command reset in the Integrator function.
0
Undefined
1

RESET

OPCMDSPG
Op_Cmd_Spg, Operator command to enable the positions in a profile in the Setpoint Ramp
function.
0
UNDEFINED
2
ADVANCED
1
RESET_IN
3
REPEAT
OUTALMSM
Out_Alm_Sum, The alarm conditions for a true Out_alm in the Analog Alarm.
0
None
8
HI_HI
1
LO_LO
9
Level2
2
LO
10
Undefined
3
Lows
11
Undefined
4
HI
12
Highs
5
Undefined
13
Undefined
6
Level1
14
Undefined
7
Undefined
15
Any

592

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Appendix A Enumerations

Enum Name

Description

PAUSCAUS
Pause_Cause, The items that cause a pause in the Setpoint Ramp function.
0
NotPaused
4
Operator&Logic
1
OperatorPause
5
Operator&Deviation
2
LogicPause
6
Logic&Deviation
3
DeviationPause
7
Operator&Logic&Deviation
PRIORTY
1
Urgent
2
Normal

FasArTypeAndRole - Transport Priority.


3

TimeAvailable

QUIESOPT
Quies_Opt, Behavior options for Out while in quiescence in the timer function.
0
Uninitialized
2
Last
1
Clear
REASON
Reason_Code, The reasons why a Function Block service fails.
1
ParameterCheck
16
WarningDataValueSet
2
ExceedsParameterLimits
17
WarningSetToNearestValue
5
DataValueNeverWritable
18
ParameterNotImplemented
7
DeleteUnsucessfull
19
IncorrectFormat
3
WrongModeForRequest
20
InvalidDate
4
WriteProhibitedByLock
21
ModeError
6
InstantiateUnsucessfull
23
AutomaticZeroError
8
AlarmAlreadyAcked
22
ProcessOutOfRange
9
Undefined
24
DeviceBusy
10
Undefined
25
UpdateFailed
11
Undefined
26
InvalidConfigurationForRequest
12
Undefined
27
ExcessCorrection
13
Undefined
28
CalibrationFailed
14
Undefined
29
CalibrationInProcess
15
Undefined
RESACTSP
0
FALSE
255
TRUE

FasDllResidualActivitySupported.

SAMPTYPE
Sample Type - Trend Sample Type.
0
NotInitialized
2
1
SampleValue
SCHEDLAS
0
Acyclic
1

AverageValue

FasDLSDAP - Schedule LAS Acyclic, Cyclic.

Cyclic

SELECT_T
Select_Type, selector action types.
0
Uninitialized
3
1
FirstGood
4
2
Min
5

Max
Mid
Avg

SERVICE
Service Operation, Service Type for LinK Objects.
0
Undefined
4
Client
1
Local
5
Server
2
Publisher
6
AlertNotify
3
Subscriber
7
TrendReport

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

593

Appendix A Enumerations

Enum Name

Description

SMSUPORT
SM (System Management) Supported Features.
0
SET_PDTAG_AGENT
7
CLR_ADDR_MGR
1
SET_ADDR_AGENT
8
IDENTIFY_MGR
2
CLR_PDTAG_AGENT
9
LOC_FB_MGR
3
IDENTIFY_AGENT
10
FMS_SERVER
4
LOC_FB_AGENT
11
TIME_SLAVE
5
SET_PDTAG_MGR
12
SCHEDULE_FB
6
SET_ADDR_MGR
13
TIME_PLUSHER
SPGSTATE
Spg_State, Operation states of the block in the Setpoint Ramp function.
0
Undefined
3
Pause
1
Ready
4
AT_End
2
Active
STANDTYP
StandardTypes - Standard Type of Alerts.
0
Undefined
7
1
Lo
8
2
HI
9
3
LoLo
10
4
HiHi
11
5
DvLo
12
6
DvHi

Disc
Block
UpdateData
Write
UpdateLink
UpdateTrend

STRTTYPE
Start_Type, The starting point options in the Setpoint Ramp function.
0
Uninitialized
2
UseDuration
1
UseCurve
3
UseRate
TIMECLAS
DL Timeliness Class.
0
None
1
Resident
2
Update
3
Synchronous

4
5
6
7

Transparent
Reserve1
Reserve2
Reserve3

TIMEUNIT
0
1
2

Time_Units, The selector for time units for display in the Pulse Input, Setpoint ramp and
Timer functions.
Uninitialized
3
Minutes
Seconds
4
Days
Hours
5
[day-[hr:[min[:sec]]]]

TIMRTYPE
0
Measure
1
Accum
2
Compare
3
Delay

Timer_Type, The type of time processing applied to PV in the Timer function.


4
Extend
5
Debounce
6
Pulse
7
RT_Pulse

TRUFALSE
0
FALSE
1
TRUE

Boolean, The state of False = 0, True = 1.

TYPEROLE
VCR Type and Role together.
0
NotConfig
50
Server,QUB
68
Source,QUU
84
Sink,QUU

594

102
118
162

Publisher,BNU
Subscriber,BNU
Client,QUB

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Appendix A Enumerations

Enumeration

Description

UNACKNOW

0
1

UNACKNOWLEDGED, A discrete enumeration which is set to Unacknowledged when an alarm


occurs, and set to Acknowledged by a write from a human interface device or other entity which
can acknowledge that the alarm/event has been noticed.
Undefined
2
Unacknowledged
Acknowledged

UNACKSUM
Unacknowledge, The unacknowledged state of each alarm.
0
Disc_Alm_Unack
4
Lo_Alm_Unack
1
HiHi_Alm_Unack
5
DevHi_Alm_Unack
2
Hi_Alm_Unack
6
DevLo_Alm_Unack
3
LoLo_Alm_Unack
7
Block_Alm_Unack

R610
11/99

HPM Parameter Reference Dictionary


Honeywell Inc.

595

Appendix A Enumerations

Enumeration
UNITS
1000
1001
1002
1003
1004
1005
1006
1009
1010
1011
1012
1013
1014
1032
1033
1034
1040
1041
1043
1044
1045
1046
1047
1048
1049
1052
1053
1054
1055
1056
1057
1060
1061
1067
1068
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088

596

Description

The engineering units associated with a PV


K (Kelvin)
1089
g
1090
mg ( milligram )
C (Celsius)
1091
Mg ( megagram )
F (Fahrenheit)
1092
t ( metric ton )
R (Rankine)
r (radian)
1093
oz
1094
lb
(degree)
' ( minute )
1095
Ston (short ton = 2000 pounds)
rev ( revolution )
1096
Lton (long ton = 2240 pounds)
m ( meter )
1097
kg/m (kilograms per cubic meter )
km ( kilometer )
1098
Mg/m (megagrams per cubic meter)
cm ( centimeter )
1099
kg/dm (kilograms per decimeter)
mm ( millimeter )
1100
g/cm (grams per cubic centimeter)
m ( micrometer )
1101
g/m (grams per cubic meter)
yd
1103
kg/L (kilograms per liter)
mile
1104
g/ml (grams per milliliter)
m ( cubic meter )
1105
g/L (grams per liter)
ml
1106
lb/in (pounds per cubic inch)
hl ( mililiter )
1107
lb/ft (pounds per cubic foot)
ft
1108
lb/gal (pound per gallon)
yd ( cubic yard )
1110
DegTwad (degrees Twaddell = 200SGU200)
mile ( cubic mile )
1111
DegBaum hv (degrees Baume heavy = 0
for 1.842 SGU)
pint
1118
kg-m (kilogram square meter)
2
quart
1120
N (newton; 1N=1kg-m/s )
gallon
1121
MN (meganewton)
ImpGal
1122
kN (kilonewton)
bbl (liq)
1123
mN (millinewton)
SCF
1124
N (micronewton))
s
1125
kg-m/s (kilogram square meter per
second)
ks
1126
N-m (newton meter)
ms ( milisecond )
1127
MN-m (meganewton meter
s ( microsecond )
1128
kN-m (kilonewton meter
d
1129
mN-m (millinewton meter
m/s
1130
Pa (pascal)
ft/s
1131
GPa (gigapascal)
yd/s
1132
MPa (megapascal)
ft/min
1133
kPa (kilopascal)
yd/min
1134
mPa (millipascal)
in/h
1135
Pa (micropascal)
ft/h
1136
hPa (hectopascal)
yd/h
1137
bar (1 bar = 100 kPa)
MPH
1138
mbar (millibar; 1 millibar = 1 hPa)
m/s ( meter per second per second )
1139
torr (1 torr = 1mmHg)
Hz
1140
atm (atmospheres = 14.7 psia; 760 mmHg)
THz
1141
psi (pounds per square inch)
GHz
1142
psia (pounds per square inch absolute)
MHz
1143
psig (pounds per square inch guage)
kHz
1144
g/cm (grams per square centimeter)
1/s
1145
kg/cm (kilograms per sqare centimeter)
1/min
1146
inH2O (inches of water)
rev/s ( revolutions per second)
1147
inH2O (4C)
RPM
1148
inH2O (68F)
r/s ( radian per second )
1149
mmH2O (millimeters of water; 1 mmH20 =
.098 hPa)
1/s
kg

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Appendix A Enumerations

Enum Name

Description

UNITS (continued)
1150
mmH2O (4C) (millimeters of water at 4C)
1151
mmH2O (68F) (millimeters of water at
68F)
1152
ftH2O (feet of water)
1153
ftH2O (4C) (feet of water at 4C)
1154
ftH2O (68F) (feet of water at 68F)
1155
inHg (inches of mercury; 1 inHg = 13.6
inH20)
1156
inHg (0C) (inches of mercury at 0 C)
1157
mmHg (millimeters of mercury; 1 mmHg =
1.333 hPa))
1158
mmHg (0C) (millimeters of mercury at
0C)
1159
Pa-s (Pascal second)
1160
M/s (square meter per second)
1161
P (poise)
1162
cP (centipoise; 1cP=1 mPa-s absolute
viscosity)
1163
St (stokes)
2
1164
cSt (centistokes; 1cSt=1mm /s kinematic
viscosity)
1165
N/m (newton per meter)
1166
mN/m (millinewton per meter)
1167
J (joules; 1 J=1N-m)
1168
EJ (exajoules))
1169
PJ (petajoules)
1170
TJ (terajoules)
1171
GJ (gigajoules)
1172
MJ (megajoules)
1173
kJ (kilojoules)
1174
mJ (jillijoules)
1175
WH (watt hour; 1 W-h=3.6 kJ)
1176
TWH (terawatt hour)
1177
GWH (gigawatt hour)
1178
MWH (megawatt hour)
1179
KWH (kilowatt hour)
1180
cal (calorie = 4.184J)
1181
kcal (kilocalorie)
1182
Mcal (metacalorie)
1183
Btu (British thermal unit; 1 Btu=0.2519958
kcal)
1187
TW (terawatt)
1188
GW (gigawatt)
1189
MW (megawatt)
1190
KW (kilowatt)
1191
mW (milliwatt)
1192
W (microwatt)
1193
nW (nanowatt)
1194
pW (picowatt)
1195
Mcal/h (megacalorie per hour)
1196
MJ/h (megajoule per hour)
1197
Btu/h (British thermal unit per hour)

R610
11/99

1198
1199

Hp (horse power; = 746 W)


W/(m-K) (watts per meter kelvin)

1200
1201
1202
1203

W/(m-K) (watts per square meter kelvin)


m-K/W (square meter kevin per watt)
J/K (joules per kelvin)
kJ/K (kilojoule per kelvin)

1204
1205

J/(kg-K) ( joule per kilogram kelvin )


kJ/(kg-K) ( kilojoule per kilogram kelvin )

1206

J/kg ( joule per kilogram )

1207
1208
1209
1210

MJ/kg ( megajoule per kilogram )


kJ/kg ( kilojoule per kilogram )
A ( ampere )
kA ( kiloampere )

1211
1212

mA ( milliampere )
A ( microampere )

1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231

nA ( nanoampere )
pA ( picoampere )
C ( coulomb )
MC ( megacoulomb)
kC ( kilocoulomb)
C ( microcoulomb)
nC ( nanocoulomb)
pC ( picocoulomb)
A-h ( ampere hour) (1A-h = 3.6kC)
C/m (coulomb per cubic meter)
C/mm (coulomb per cubic millimeter)
C/cm (coulomb per cubic centimeter)
kC/m (kilocoulomb per cubic meter)
mC/m (millicoulomb per cubic meter)
C/m (microcoulomb per cubic meter)
C/m
C/mm
C/cm
kC/m

1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242

mC/m
mC/m
V/m (volt per meter)
MV/m (megavolt per meter)
kV/m (kilovolt per meter)
V/cm
mV/m (millivolt per meter)
V/m (microvolt per meter)
V (volt = 1 W/A)
MV (megavolt)
KV (kilovolt)

HPM Parameter Reference Dictionary


Honeywell Inc.

597

Appendix A Enumerations

Enum Name

Description

UNITS (continued)
1243
mV (millivolt)
1244
V (microvolt)
1245
F (farad = 1 C/V)
1246
mF
1247
F
1248
nF
1249
pF
1250
F/m
1251
F/m
1252
nF/m
1253
pF/m
1254
C-m (coulomb meter)
1255
A/m
1256
MA/m
1257
A/cm
1258
kA/m
1259
A/m
1260
kA/m
1261
A/cm
2
1262
T (tesia = 1 Wb/m )
1263
mT (millitesia)
1264
T
1265
nT
1266
Wb (weber = 1 V-s)
1267
mWb
1268
Wb/m
1269
kWb/m
1270
H (henry = 1 Wb/A)
1271
mH
1272
H
1273
nH
1274
pH
1275
H/m
1276
H/m
1277
nH/m
1278
A-m
1279
N-m/A (newton square meter per ampere)
1280
Wb-m (weber meter)
1281
Ohm (Ohm; 1 ohm = 1 V/A)
1282
GOhm (gigaOhm)
1283
MOhm (megaOhm)
1284
kOhm (kiloOhm)
1285
mOhm (milliOhm)
1286
Ohm (microOhm)
1287
S (siemens; 1 S = 1 /ohm2)
1288
kS
1289
mS
1290
S
1291
Ohm-m (ohm meter)
1292
GOhm-m

598

1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342

MOhm-m
kOhm-m
Ohm-cm
mOhm-m
Ohm-m
nOhm-m
S/m (siemens per meter)
MS/m
kS/m
mS/cm
S/mm
1/H (per henry)
sr (steradian)
W/sr (watt per steradian)
W/(sr-m)
W/(m)
lm (lumen; 1 lumen = 1 cd-sr)
lm-s (lumen second)
lm-h (lumen hour = 3600 lm-s)
lm/m
lm/W
2
lx (lux = 1 lm/m )
lx-s (lux second)
cd (candela; Sl)
cd/m
g/s (gram per second)
g/min (gram per minute)
g/h (gram per hour)
g/d (gram per day)
kg/s (gram per second)
kg/min (gram per minute)
kg/h (gram per hour)
kg/d (gram per day)
3
t/s (metric ton per second; 1 t = 10 kg)
t/min
t/h
t/d
lb/s
lb/min
lb/h
lb/d
STon/s (short ton per second)
STon/min
STon/h
STon/d
LTon/s (long ton per second)
LTon/min
LTon/h
LTon/d
%

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Appendix A Enumerations

Enum Name

Description

UNITS (continued)
1343
% sol/wt (percent solids per weight)
1344
% sol/vol (percent solids per volume)
1345
% stm qual (percent solids per quality)
1346
% plato (percent plato; % sugar by weight)
1347
m/s (cubic meters per second)
1348
m/min (cubic meters per minute)
1349
m/h (cubic meters per hour)
1350
m/d (cubic meters per day)
1351
L/s (liter per second)
1352
L/min (liter per minute) )
1353
L/h (liter per hour)
1354
L/d (liter per day)
1355
ML/d (megaliter per day)
1356
CFS (cubic feet per second)
1357
CFM (cubic feet per minute)
1358
CFH (cubic feet per hour)
3
1359
ft /d (cubic feet per day)
1360
SCFM (cubic feet per second)
1361
SCFH (cubic feet per hour)
1362
gal/s (US gallons per second)
1363
GPM (US gallons per minute)
1364
gal/h (US gallons per hour)

1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416

1365
1366
1367
1368
1369
1370

1417
1418
1419
1420
1421
1422

1371
1372
1373
1374
1375

gal/d (US gallons per day)


Mgal/d (mega US gallon per day)
ImpGal/s (Imperial gallon per second)
ImpGal/min (Imperial gallon per minute)
ImpGal/h (Imperial gallon per hour)
ImpGal/d (Imperial gallon per day;
1bbl=42US gallons)
bbl/s (barrel per second)
bbl/min (barrel per minute)
bbl/h (barrel per hour)
bbl/d (barrel per day)
W/m (watt per square meter)

1423
1424
1425
1426
1427

1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394

mW/m (milliwatt watt per square meter)


W/m (microwatt per square meter)
pW/m (picowatt per square meter)
Pa-s/m (pascal second per cubic meter)
N-s/m (newton second per meter)
Pa-s/m (pascal second per meter)
B (bel)
-1
dB (decibel = 10 B)
mol (mole)
kmol (kilomole)
mmol (millimole)
mol (micromole)
kg/mol (kilogram per mole)
g/mol (gram per mole)
m/mol (cubic meter per mole)
dm/mol (cubic decimeter per mole)
cm/mol (cubic centimeter per mole)
L/mol (liters per mole)
J/mol (joule per mole)

1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446

R610
11/99

kJ/mol (kilojoule per mole)


J/(mol-K) (joule per mole kelvin)
mol/m (mole per cubic meter)
mol/dm (mole per cubic decimeter)
mol/L (mole per liter)
mol/kg (mole per kilogram)
mmol/kg (millimole per kilogram)
-1
Bq (becquerel; 1 Bq = 1-s )
MBq (megabecquerel)
kBq (kilobecquerel)
Bq/kg (becquerel per kilogram)
kBq/kg (kilobecquerel per kilogram)
MBq/kg (megabecquerel per kilogram)
Gy (gray = 1 J/kg)
mGy (milligray)
-2
rad (rad = 10 Gy)
Sv (sievert; 1 Sv = 1 J/kg)
mSv (millisievert)
-2
rem (rem; 1 rem = 10 Sv)
C/kg (coulomb per kilogram)
mC/kg (millicoulomb per kilogram)
R (rntgen; 1 R = 2.58 x 10-4 C/kg)
1/J-m
e/V-m
m/C (cubic meter per coulomb)
V/K (volt per kelvin)
mV/K
pH
ppm
ppb
ppt
degBrix (degrees Brix; % sugar by weight)
degBall (degrees Balling; % sugar by
weight)
proof/vol
proof/mass
lb/ImpGal
kcal/s (kilocalorie per second)
kcal/min
kcal/h
kcal/d
Mcal/s (megacalorie per second)
Mcal/min
Mcal/d
kJ/s (kilojoules per second)
kJ/min
kJ/h
kJ/d
MJ/s (megajoules per second)
MJ/min
MJ/d
Btu/s
Btu/min

HPM Parameter Reference Dictionary


Honeywell Inc.

599

Appendix A Enumerations

Enum Name

Description

UNITS (continued)
1447
Btu/day
1448
gal/s (micro US gallon per second)
1449
mgal/s (milli US gallon per second)
1450
kgal/s
1451
Mgal/s
1452
gal/min
1453
mgal/mi
1454
kgal/min
1455
Mgal/min
1456
gal/h
1457
mgal/h
1458
kgal/h
1459
Mgal/h
1460
gal/d
1461
mgal/d
1462
kgal/d
1463
ImpGal/s (micro imperial gallon per
second)
1464
mImpGal/s
1465
kImpGal/s
1466
MImpGal/s
1467
ImpGal/min
1468
mImpGal/min
1469
kImpGal/min
1470
MImpGal/min
1471
ImpGal/h
1472
mImpGal/h
1473
kImpGal/h
1474
MImpGal/h
1475
ImpGal/d
1476
mImpGal/d
1477
kImpGal/d
1478
MImpGal/d
1479
bbl/s (microbarrel per second)
1480
mbbl/s (millibarrel per second)
1481
kbbl/s (kilobarrel per second)
1482
Mbbl/s (megabarrel per second)
1483
bbl/min
1484
mbbl/min
1485
kbbl/min
1486
Mbbl/min
1487
bbl/h
1488
mbbl/h
1489
kbbl/h
1490
Mbbl/h
1491
bbl/d
1492
mbbl/d
1493
kbbl/d
1494
Mbbl/d
1495
m/s (cubic micrometer per second)
1496
mm/s
1497
km/s
1498
Mm/s

600

1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515

m/min
mm/min
km/min
Mm/min
m/h
mm/h
km/h
Mm/h
m/d
mm/d
km/d
Mm/d
cm/s (cubic centimeter per second)
cm/min
cm/h
cm/d
kcal/kg (kilocalorie per kilogram)

1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550

Btu/lb
kL (kiloliter)
kL/min
kL/h
kL/d
unit_code1521
unit_code1522
unit_code1523
unit_code1524
unit_code1525
unit_code1526
unit_code1527
unit_code1528
unit_code1529
unit_code1530
unit_code1531
unit_code1532
unit_code1533
unit_code1534
unit_code1535
unit_code1536
unit_code1537
unit_code1538
unit_code1539
unit_code1540
unit_code1541
unit_code1542
unit_code1543
unit_code1544
unit_code1545
unit_code1546
unit_code1547
unit_code1548
unit_code1549
unit_code1550

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Appendix A Enumerations

Enum Name

Description

UNREPSUM
Unreported, The unreported status of each
0
Disc_Alm_Unrep
4
1
HiHi_Alm_Unrep
5
2
Hi_Alm_Unrep
6
3
LoLo_Alm_Unrep
7

Alarm.
Lo_Alm_Unrep
DevHi_Alm_Unrep
DevLo_Alm_Unrep
Block_Alm_Unrep

UPDSTATE
Update State, A discrete enumeration which gives an indication of whether the alert has been
reported.
0
Undefined
2
Not_Reported
1
Reported
VCRROLE
VCR send-receive Roles
0
NotConfig
1
Responder
2
Undefined
3
Server
4
Source
5
Sink
VCRTYPE
VCR Data Transport Type
0
NotConfig
1
QUB

R610
11/99

6
7
8
9
10

Publisher
Subscriber
Undefined
Initiator
Client

2
3

QUU
BNU

HPM Parameter Reference Dictionary


Honeywell Inc.

601

Appendix A Enumerations

602

HPM Parameter Reference Dictionary


Honeywell Inc.

R610
11/99

Fax Transmittal

Fax No.:

(602) 313-4842

Reader Comments
To:

Automation College

From: Name

Date:

Title:
Company:
Address:
City:
Telephone:

State:

Zip:

Fax:

HPM Parameter Reference Dictionary, Release 610, 11/99


Comments:

You may also call 800-822-7673 (available in the 48 contiguous states except Arizona; in Arizona
call 602-313-5558), email us at College.Automation@iac.honeywell.com, or write to:
Honeywell Inc.
Industrial Automation and Control
Automation College
2820 West Kelton Lane
Phoenix, AZ 85053-3028

Initiative
Knowledge Building Tools

Industrial Automation and Control


Honeywell Inc.
2820 West Kelton Lane
Phoenix, AZ 85053-3028

You might also like