Professional Documents
Culture Documents
command
for importance of the
located inside surface 10
cell
with imp for photons of 1
can also be defined in block 3
x type of particle
Cell 20
p for photons
composed of material 1 defined in
e for electrons
block 3 (Fe) [only one material per
n for neutrons
cell]
3
z
value
of importance
with density of -7.86 g/cm
usually 1 for source
located in the space of intersection of
cells closer to tally region have
R of surface 10 and left of surface 20
high importance
with imp for photons of 1
if z=0, kill particles that enter the
cell
if z=1, track particle normally
BLOCK 2: SURFACE CARD + MACROBODIES
ID surface number
ID Mn CE
Mn mnemonic for surface type(see table)
CE card entries (eg. radius, x-coord)
eg. 10 so 30.0
20 c/z 5 5 10
Surface 10
Sphere centered at origin
R=30.0 cm
Surface 20
eg.
100 so 1000 (edge of universe)
cylinder parallel to z-axis
x & y-int = 5,5; R = 10.0 cm
BLOCK 3: DATA CARD
Mx material number (eg. M1, M20, etc.)
ZZZ atomic number (O = 008, Fe = 026)
AAA mass number
000 for elementals
AAA for isotopes (eg. 235U = 235) w/c
Mx ZZZAAA.nnX y
are usually used for neutron transport
.nnX cross section compilation identifier
(Material Specification)
y atomic abundance (eg. for H2O, H is 2
and O is 1)
x mass fraction (eg. for H2O, H is
M1 8016 1
-0.11190 and O is -0.88810)
M2 26000 1
mass fraction = mz/mtot
M3 6000 1
if g/cm3 is used (-)
no density component to allow one
material to appear at various densities
ZZZAAA.nnX
(Cross Section Specification)
SDEF
(Source Specification)
POS = x y z
MODE x
IMP:X C C C C
IMP:N 1 1 1 0
F1:X Y
F2:X Y
F4:X Y
F5:X Y
F6:X Y
F7:X Y
F8:X Y
(Tally Specification)
NPS N
(History Card)
CTME T
PHYS:P EMCPF IDES NOCOH PNINT
NODOP
PHYS:P 100 0 0 0 0 $100MeV, brems, coh
scat, no photonuc, Doppler
C, $
st
En E1 E2 E3 E4
(Tally Energy Card)
E24 1 2 3 4 (up to 4 MeV)
En E1 ni Emax $ n equispaced bins between
E1 and Emax
on/off
physics simplification for neutron
EMAX = energy in MeV above which
neutron data is not placed in memory
EMCNF = energy in MeV wherein
neutrons below EMCNF is treated by
analogue capture while above EMCNF
is treated by implicit capture
IUNR = if 1, avgd XS above resolved
XS are used; if 0, prob tables descr
interactions are sampled
DNB specifies if v(E) includes prompt
+delayed n (-1) or if only prompt n (0)
or delayed n per fission are to be used
(>0)
Comment cards which can be place
anywhere in input file
C should be followed by a space and be
found at columns 1-5
$ terminated data entry on a line
5 blanks indicate a continuation of data
from the last name card
& ending a line indicates data will
continue on the following card
When you wish to subdivide total flux
or current tally number into energy
groups
See flux as a function of energy
Results for tally 24 (type F4) are binned
in 4 energy groups
If En card is absent, only one bin over
all energies
E0 card = sets up a default energy bin
for ALL tallies
Title Card
Cell Card
Blank Line
Surface Cards
Blank Line
Mode
Source (only KCODE and ksrc if they exist)
Materials
Transformations
Importances
Other data (VOL, PWT, EXT, FCL, PD, DXC, NONU, WWN, TMP)
Data not recognized by visual editor