You are on page 1of 17

10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes

SYSNET NOTES
MicroSoft | Cisco | PaloAlto| Networking Notes| Tips | Troubleshooting
Search

Home Cisco> Routing > Switching > PaloAlto Security Cmd Prompt More>

CCNA (200-120) Quick notes before exam


by Shabeer ibm

I prepared this notes after passing my CCNA 200-120.This last minute quick
notes are only intended to refresh your knowledge. Make sure you know
everything mentioned here before attending the CCNA 200-120 exam.For
complete and detailed CCNA notes click here

Points to Remember

By default router can break up broadcast domains.You need vlans in switches to


break broadcast domains
Both router and switch can break up collision domains
Routing occur in internet layer in DOD TCP/IP reference model
PPP perform in layer 2
FTP belongs to Application layer
When Global command that is set once and affects the entire router
LCP PPP sub protocol negotiates authentication options
PPP and DSL are valid WAN connectivity methods
Rapid Spanning Tree Protocol, an enhancement to Spanning Tree Protocol is
used to prevent loops
When using the term “frame” we can easily recognize it belongs to the Data Link
layer
When using the term “Packet” we can easily recognize it belongs to the Network
layer

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 1/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here
Show version to View and
command Download
reveals complete
the last methodCCNA
used+to
CCNP PDF Notes
powercycle a router
show ip interface command is used to verify which interfaces are affected by
the ACL
Both routers must use the same password for CHAP to authentication 

Basic notes
To check the connectivity between a host and a destination (through some networks)
we can use both “tracert” and “ping” commands. But the difference between these 2
commands is the “tracert” command can display a list of near-side router interfaces
in the path between the source and the destination. The “traceroute” command has
the same function of the “tracert” command but it is used on Cisco routers only, not
on a PC 

When powered on, the router first checks its hardware via Power-On Self Test
(POST). Then it checks the configuration register to identify where to load the IOS
image from. In the output above we learn that the Configuration register value is
0×2102 so the router will try to boot the system image from Flash memory first.

The last known good router will try to inform you that the destination cannot be
reached (with a Destination Unreachable message type) so from that information
you can learn how far your packets can travel to and where the problem is.

Each interface on a router must be in a different network. If two interfaces are in the
same network, the router will not accept it and show error when the administrator
assigns it.
When no startup configuration file is found in NVRAM, the System Configuration
Dialog will appear to ask if we want to enter the initial configuration dialog or not.

Ping command can be used from a PC to verify the connectivity between hosts that
connect through a switch in the same LAN

Organizational Unique Identifier (OUI) is the first 24 bits of a MAC address for a
network device, which indicates the specific vendor for that device as assigned by
the Institute of Electrical and Electronics Engineers, Incorporated (IEEE). This
identifier uniquely identifies a vendor, manufacturer, or an organization.

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 2/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here
The Maximum to View andUnit
Transmission Download
(MTU)complete CCNA
defines the + CCNP PDF
maximum Notes
Layer 3 packet (in
bytes) that the layer can pass onwards.

Modern Ethernet networks built with switches and full-duplex connections no


longer utilize CSMA/CD. CSMA/CD is only used in old switches

The Network layer is responsible for network addressing and routing through the
internetwork. So a ping fails, you may have an issue with the Network layer.Packets
are created when the network layer adds Layer 3 addresses and control information
to a segment.

 The transport layer divides a data stream into segments and may add reliability
and flow control information. 

Application layer in the OSI reference model is responsible for determining the
availability of the receiving program and checking to see if enough resources exist
for that communication

When upgrading new version of the IOS we need to copy the IOS to the Flash so first
we have to check if the Flash has enough memory or not. Also running the new IOS
may require more RAM than the older one so we should check the available RAM
too. We can check both with the “show version” command.

When will devices transmit in a Ethernet network ?


Ethernet network is a shared environment so all devices have the right to access to
the medium. If more than one device transmits simultaneously, the signals collide
and cannot reach the destination. If a device detects another device is sending, it will
wait for a specified amount of time before attempting to transmit. When there is no
traffic detected, a device will transmit its message. While this transmission is
occurring, the device continues to listen for traffic or collisions on the LAN. After the
message is sent, the device returns to its default listening mode.

Two purposes does the Ethernet protocol use physical addresses


Physical addresses or MAC addresses are used to identify devices at layer 2
To allow communication between different devices on the same network

The following locations can be configured as a source for the IOS image:
Flash (the default location)

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 3/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

TFTPClick here to View and Download complete CCNA + CCNP PDF Notes
server
ROM (used if no other source is found)

What is the difference between a CSU/DSU and a modem?


A CSU/DSU converts digital signals from a router to a leased line; a modem
converts digital signals from a router to a phone line.

Router boot process:


The Power-On Self Test (POST) checks the router’s hardware. When the POST
completes successfully, the System OK LED indicator comes on.
The router checks the configuration register to identify where to load the IOS image
from. A setting of 0×2102 means that the router will use information in the startup-
config file to locate the IOS image. If the startup-config file is missing or does not
specify a location, it will check the following locations for the IOS image:
1. Flash (the default location)
2. TFTP server
3. ROM (used if no other source is found)

Basic IOS notes


service password-encryption command, all the (current and future) passwords are
encrypted. This command is primarily useful for keeping unauthorized individuals
from viewing your password in your configuration file.

How to secure the virtual terminal interfaces on a router?


Configure a virtual terminal password and login process.
Enter an access list and apply it to the virtual terminal interfaces using the
access-class command.

Commands
Router(config)# service password-encryption command encrypts all plaintext
passwords.

Router (config-if)# ppp authentication chap pap command is used to enable CHAP


authentication with PAP as the fallback method on a serial interface 

Router#show vlan command only displays access ports, the trunk ports are not
showed in this command

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 4/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click herelmi”
"Show frame-relay to View and Download
command allows complete CCNAthe
you to verify + CCNP PDF Notes type
encapsulation
(CISCO or IETF) for a frame relay link

 show ip ospf database -  command is used to display the collection of OSPF link
states

 Below lists popular modes in Cisco switch/router:


Router> User mode

Router# Privileged mode

Router(config)# Configuration mode

Router(config-if)# Interface level (within configuration mode)

Router(config-router)# Routing engine level (within configuration mode)

Router(config-line)# Line level (vty, tty, async) within configuration mode

Trunking Notes:
Valid Vlan Trunk Modes
Desirable
Auto
ON

Dynamic Trunking Protocol (DTP) is a Cisco proprietary protocol for negotiating


trunking on a link between two devices and for negotiating the type of trunking
encapsulation (802.1Q) to be used.

IEEE 802.1Q is the networking standard that supports Virtual LANs (VLANs) on an
Ethernet network. It is a protocol that allows VLANs to communicate with one
another using a router. 802.1Q trunks support tagged and untagged frames.If a
switch receives untagged frames on a trunk port, it believes that frame is a part of
the native VLAN. Also, frames from a native VLAN are not tagged when exiting the
switch via a trunk port.

Three elements must be used when you configure a router interface for vlan
trunking? 
one IP network or subnetwork for each subinterface 
subinterface encapsulation identifiers that match vlan tags
one subinterface per vlan

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 5/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes
Cisco switches support two trunking protocols 802.1q & ISL. 802.1q is an open
standard and is thus compatible between most vendors’ equipment while Inter-
Switch Link (ISL) is Cisco proprietary.

Click here for detailed VTP notes

STP Notes

Only non-root bridge can have root port. 

The path cost to the root bridge is the most important value to determine which port
will become the root port on each non-root switch. In particular, the port with lowest
cost to the root bridge will become root port (on non-root switch).

Per VLAN Spanning Tree (PVST) maintains a spanning tree instance for each VLAN
configured in the network. It means a switch can be the root bridge of a VLAN while
another switch can be the root bridge of other VLANs in a common topology. For
example, Switch 1 can be the root bridge for Voice data while Switch 2 can be the
root bridge for Video data. If designed correctly, it can optimize the network traffic.

If we connect two switches via 2 or more links and do not enable STP on these
switches then a loop (which creates multiple copies of the same unicast frame) will
occur. It is an example of an improperly implemented redundant topology.

PVST+ is based on IEEE802.1D Spanning Tree Protocol (STP). But PVST+ has only 3
port states (discarding, learning and forwarding) while STP has 5 port states
(blocking, listening, learning, forwarding and disabled). So discarding is a new port
state in PVST+.

RSTP only has 3 port states that are discarding, learning and forwarding. When RSTP
has converged there are only 2 port states left: discarding and forwarding

A BPDU is superior than another if it has:


1. A lower Root Bridge ID
2. A lower path cost to the Root
3. A lower Sending Bridge ID
4. A lower Sending Port ID

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 6/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes
Click here for detailed STP Notes

ACL  Notes
The standard access lists are ranged from 1 to 99 and from 1300 to 1999 

We can have only 1 access list per protocol, per direction and per interface. It
means:
We can not have 2 inbound access lists on an interface
We can have 1 inbound and 1 outbound access list on an interface

We can use a dynamic access list to authenticate a remote user with a specific
username and password. The authentication process is done by the router or a
central access server such as a TACACS+ or RADIUS server.

Click here for detailed ACL notes

NAT Notes
With static NAT, translations exist in the NAT translation table as soon as you
configure static NAT command(s), and they remain in the translation table until you
delete the static NAT command(s).Because static NAT translations are always present
in the NAT table so outside hosts can initiate the connection without being dropped

With dynamic NAT, translations do not exist in the NAT table until the router
receives traffic that requires translation. Dynamic translations have a timeout
period after which they are purged from the translation table.

By not reveal the internal Ip addresses, NAT adds some security to the inside
network

By allocating specific public IP addresses to inside hosts, NAT eliminates the need to
re-address the inside hosts

VLAN Notes
A “native VLAN mismatch” error will appear by CDP if there is a native VLAN
mismatch on an 802.1Q link. “VLAN mismatch” can cause traffic from one vlan to
leak into another vlan.

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 7/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click
VLANs allow here tousers
to group View by
andfunction,
Download complete
not CCNAor
by location + geography
CCNP PDF Notes
VLANs help minimize the incorrect configuration of VLANs so it enhances the
security of the network

VLANs increase the number of broadcast domains while decreasing the size of the
broadcast domains which increase the utilization of the links. It is also a big
advantage of VLAN

Advantages of VLANs
VLANs establish broadcast domains in switched networks.
VLANs allow access to network services based on department, not physical
location.
VLANs can greatly simplify adding, moving, or changing hosts on the network.

For 802.1q encapsulation, the native VLAN must matched at both side; otherwise the
link will not work.

VLAN 1 is the default VLAN on Cisco switch. It always exists and can not be added,
modified or removed.
VLANs 1002-1005 are default VLANs for FDDI & Token Ring and they can’t be deleted
or used for Ethernet.

Click here for detailed VLAN notes

Frame Relay Notes


To configure subinterface for Frame Relay, first we have to remove the IP address
from the physical interface and choose a Frame Relay encapsulation.

The PVC STATUS displays the status of the PVC. The DCE device creates and sends the
report to the DTE devices. There are 4 statuses:
ACTIVE: the PVC is operational and can transmit data
 INACTIVE: the connection from the local router to the switch is working, but the
connection to the remote router is not available
DELETED: the PVC is not present and no LMI information is being received from the
Frame Relay switch
STATIC: the Local Management Interface (LMI) mechanism on the interface is
disabled (by using the “no keepalive” command). This status is rarely seen so it is
ignored in some books.

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 8/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes
DLCI: DLCI stands for Data Link Connection Identifier. DLCI values are used on
Frame Relay interfaces to distinguish between different virtual circuits. DLCIs have
local significance because the identifier references the point between the local
router and the local Frame Relay switch to which the DLCI is connected.

Committed information rate (CIR): The minimum guaranteed data transfer rate
agreed to by the Frame Relay switch. Frames that are sent in excess of the CIR are
marked as discard eligible (DE) which means they can be dropped if the congestion
occurs within the Frame Relay network.
Note: In the Frame Relay frame format, there is a bit called Discard eligible (DE) bit
that is used to identify frames that are first to be dropped when the CIR is exceeded.

Local Management Interface (LMI) is a signalling standard protocol used between


your router (DTE) and the first Frame Relay switch

Inverse ARP is a technique by which dynamic mappings are constructed in a


network, allowing a device such as a router to locate the logical network address and
associate it with a permanent virtual circuit (PVC).

IP Routing Notes
When one route is advertised by more than one routing protocol, the router will
choose to use the routing protocol which has lowest Administrative Distance. 
Routers decrement the TTL by 1 every time they forward a packet; if a router
decrements the TTL to 0, it throws away the packet. This prevents packets from
rotating forever

Remember these rules:


The IP addresses (of source and destination) of a packet never change during the
transportation through the network. For example if PC-A wants to send a packet to
PC-Z then the source and destination IP addresses of the packet will be the IP
addresses of PC-A and PC-Z no matter how many devices they go through.
The MAC addresses, conversely, will change while passing the devices. The source
MAC address is the address of the last sender and the destination MAC address is the
address of the next device.

The simple syntax of static route:

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 9/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download


ip route destination-network-address complete CCNA
subnet-mask + CCNP PDF Notes
{next-hop-IP-address | exit-
interface}

Explanation
destination-network-address: destination network address of the remote network
subnet mask: subnet mask of the destination network
next-hop-IP-address: the IP address of the receiving interface on the next-hop
router
exit-interface: the local interface of this router where the packets will go out

DHCP Notes
Network or sub network IP address and broadcast address should never be
assignable to hosts. When try to assign these addresses to hosts, you will receive an
error message saying that they can’t be assignable.

An address conflict occurs when two hosts use the same IP address. During address
assignment, DHCP checks for conflicts using ping and gratuitous ARP. If a conflict is
detected, the address is removed from the pool. The address will not be assigned
until the administrator resolves the conflict.

OSPF Notes
The highest IP address of all loopback interfaces will be chosen as Router-ID
110 is the default administrative distance of OSPF

The default number of equal-cost paths that can be placed into the routing of a Cisco
OSPF router is 4. We can change this default value by using “maximum-paths”
command:
Router(config-router)#maximum-paths 2
Note: Cisco routers support up to 6 equal-cost paths

Characteristics of a link-state routing protocol


Provides common view of entire topology
Calculates shortest path
Utilizes event-triggered updates

Describe the routing protocol OSPF


It supports VLSM.
It confines network instability to one area of the network.

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 10/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Clickextensive
It allows here to View and Download
control of routingcomplete
updatesCCNA + CCNP PDF Notes

Hierarchical design of OSPF (basically means that you can separate the larger
internetwork into smaller internetworks called areas) helps us create a network
with all features listed like (decrease routing overhead, speed up convergence;
confine network instability to single areas of the network).

Hello packets and LSAs from other routers are used by router running a link-state
protocol to build and maintain its topological database

To form an adjacency (become neighbour), router A & B must have the same Hello
interval, Dead interval and AREA number.

Click here for detailed OSPF notes

EIGRP Notes
Make sure you know how to configure and troubleshoot EIGRP.

AD of EIGRP Internal Route is 90


AD of EIGRP external Route is 170
AD of EIGRP summary Route is 5

Passive Interface: In EIGRP (and OSPF) the passive interface command stops
sending outgoing hello packets, hence the router cannot form any neighbor
relationship via the passive interface. This behavior stops both outgoing and
incoming routing updates

Feasible successor is a route whose Advertised Distance is less than the Feasible
Distance of the current best path. A feasible successor is a backup route, which is not
stored in the routing table but stored in the topology table.

EIGRP stub advertises summary and directly connected routes. EIGRP stub routing
feature improves network stability, reduce resources utilization and simplifies stub
router configuration. Any neighbor that receives a packet informing it of the stub
status will not query the stub router for any routes.EIGRP stub configuration
command increases scalability by limiting the
EIGRP query range

Active State: When a route (current successor) goes down, the router first checks its
topology table for a feasible successor but it can’t find one. So it goes active on the

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 11/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

that route to find


Click a new
here successor
to View by sending
and Download queries
complete out +toCCNP
CCNA its neighbors
PDF Notesrequesting
a path to the lost route.

Click here for detailed EIGRP Notes

Security Notes
We only enable PortFast feature on access ports (ports connected to end stations).
But if someone does not know he can accidentally plug that port to another switch
and a loop may occur when BPDUs are being transmitted and received on these
ports.
With BPDU Guard, when a PortFast receives a BPDU, it will be shut down to prevent
a loop

We can verify whether port security has been configured by using the “show
running-config” or “show port-security interface” for more detail

Port security is only used on access port (which connects to hosts) so we need to set
that port to “access” mode, then we need to specify the maximum number of hosts
which are allowed to connect to this port.
Note: If we want to allow a fixed MAC address to connect, use the “switchport port-
security mac-address ” command.

One of the most widely deployed network security technologies today is IPsec over
VPNs. It provides high levels of security through encryption and authentication,
protecting data from unauthorized access.

IPV6 Notes
Features of the IPv6 protocol
Autoconfiguration
No broadcasts
Plug-and-play
A single interface may be assigned multiple IPV6 addresses of any type.
Every IPV6 interface contains at least one loopback address.

With IPv6, devices can build a link-local address automatically. But notice this
address is only used for communications within the local subnetwork, routers do not
forward these addresses.
Below is the list of common kinds of IPv6 addresses:

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 12/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

LoopbackClick here to View


address ::1 and Download complete CCNA + CCNP PDF Notes

Link-local address FE80::/10

Site-local address FEC0::/10

Global address 2000::/3

Multicast address FF00::/8

Click here for Detailed IPv6 notes

SNMP protocol can cause overload on a CPU of a managed device


TRAP and INFORM are the alert message generated by SNMP agents
In a GLBP network, AVG is responsible for the arp request

Components of SNMP
MIB
SNMP Manager
SNMP Agent

3 features are added in SNMPv3 over SNMPv2


Message Integrity
Authentication
Encryption 

Popular destinations for syslog messages to be saved


The logging buffer .RAM
The console terminal
Syslog server

The benefit of using Netflow


Network, Application & User Monitoring
Security Analysis
Accounting/Billing

3 things that the Netflow uses to consider the traffic to be in a same flow
IP address
Port numbers
L3 protocol type

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 13/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes
Related articles

Gateway Redundancy Protocols (HSRP)  


Configuring Basic OSPF 
OSPF Authentication  
Cisco Discovery Protocol (CDP)  
Quick reminder about HSRP 
EIGRP Configuration and Troubleshooting commands 
Top 10 'show' Commands  

11 Comments:

Tony
October 4, 2013 at 12:29 PM

Hi Shabeer,

you are an absolute life saver for the little details that i missed studying for 640-802. I
scored 801/1000 :(

Now that i am in the process of studying for and sitting the 200-120 exam i wanted to
know what the process for getting a copy of the notes from your blog was?
REPLY

Shabeer Ibm
October 4, 2013 at 12:33 PM

You can download Complete PDF via paypal

REPLY

Anonymous
December 13, 2013 at 8:14 AM

Thanks shabeer this notes really helped me to pass CCNA in first attempt
REPLY

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 14/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes
Faarah Adam
November 23, 2014 at 5:36 AM

Hi Shabeer, I bought the notes and downloaded the Zip file, but when I tried to extract
them I get asked for a password. please help.

Faarah Adam (abdimayah@gmail.com)


REPLY

Shabeer Ibm
November 24, 2014 at 8:29 PM

I already forwarded the updated PDF notes to your email.Hope my notes helps in
your studies

REPLY

Jonathan
January 5, 2015 at 2:16 PM

This post is awesome.it helped me lot for last moment preparation


REPLY

Derek
January 5, 2015 at 2:18 PM

Thank you Shabeer.This post was outstanding.Really helped me prepare for the test the
last day.
REPLY

Irwin Williams
January 23, 2015 at 8:22 PM

CCNA Routing and Switching is for set of connections consultant, Network


Administrators, and Network Support Engineers with 1-3 years of knowledge. The CCNA
Routing and Switching authorize the capability to put in, put together, activate, and
troubleshoot medium-size routed and switched set of connections.
REPLY

Irwin Williams
January 23, 2015 at 8:28 PM

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 15/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes
CCNA Routing and Switching is for set of connections consultant, Network
Administrators, and Network Support Engineers with 1-3 years of knowledge. The CCNA
Routing and Switching authorize the capability to put in, put together, activate, and
troubleshoot medium-size routed and switched set of connections
REPLY

Anonymous
May 20, 2015 at 9:08 PM

Blog is awesome. Thank you


REPLY

Faryal Naaz
December 16, 2015 at 8:54 PM

Valuable information ..I am delighted to read this article..thank you for giving us this
useful information.
CCNA Routing and Switching
REPLY

Enter your comment...

Comment as:  taurai (Google) Sign out

 
Publish Preview   Notify me

Links To This Post

Create a Link

NEXT POST: Short Note on Etherchannel


PREVIOUS POST: Top 10 'show' Commands

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 16/17
10/2/2016 CCNA (200­120) Quick notes before exam ~ Sysnet Notes

Click here to View and Download complete CCNA + CCNP PDF Notes
VISITORS FACEBOOK FOLLOW BY EMAIL
Live Traffic Feed
A visitor from Harare, Sysnetnotes Email address... Submit
437 likes
Mashonaland East viewed
"CCNA (200­120) Quick notes
before exam ~ Sysnet Notes" 4 BUY PDF NOTES
A visitor from India viewed
mins ago V I A PAY PA L
Like Page Share
"Home ~ Sysnet Notes" 16 mins
CCNA + CCNP PDF
ago notes + Interview
A visitor from San Francisco, Be the first of your friends to like thisQuestions for 10$
California viewed "Passive
Interface (RIP,OSPF and
CCNA PDF notes and
EIGRP) explained with Interview questions
interview questions ~ Sysnet for 7$
A visitor from San Francisco,
Notes" 21 mins ago
California viewed "Spanning­
tree protocol Notes with
Interview Questions ~ Sysnet T O TA L PA G E V I E W S
A visitor from Bhopal, Madhya
Notes" 22 mins ago
Pradesh viewed "Home ~ SysnetLABELS 1,981,624
Notes" 22 mins ago AAA Access list Active
directory ARP ASA basic
A visitor from Mumbai,
Maharashtra viewed "OSI Basics Batch file BGP
Reference model notes with CCNA CCNP
interview questions ~ Sysnet
A visitor from Chamalières, Routing
Notes" 25 mins ago CCNP
Auvergne viewed "Sysnet Switching cisco
Notes" 25 mins ago cmd prompt
A visitor from Chicago, Illinois
viewed "How to Prepare for Commands
NETWORK ENGINEER Configuration DHCP
INTERVIEW QUESTIONS ~EIGRP error
A visitor from San Francisco,Etherchannel
Sysnet Notes" 33 mins ago FAQ
California viewed "How to pingFirewall FortiGate GPO
multiple ip addresses from cmdHSRP internet explorer
prompt ~ Sysnet Notes" 38 minsInterview IPv6 Kali
A visitor from India viewed kaspersky
ago LAB linux
"Basic Notes on OSPF (Open Lockout lotus notes
Shortest Path First) ~ Sysnet magicjack MCP MPLS MST
network monitoring
Notes" 43 mins ago
Real­time view · Get Feedjit OSPF paloalto Private
Security
VLAN Routing
short notes software
SPAN Static routing STP
Switching tips
Troubleshooting
VLAN VMware VPN
VTP windows wireless

© 2013 Sysnet Notes

http://sysnetnotes.blogspot.com/2013/10/ccna­200­120­quick­notes­before­exam.html 17/17

You might also like