Professional Documents
Culture Documents
2.1 Introduction
Conventionally, the RNC pages a UE in idle mode for CS services in the entire location area (LA). If, at the
paging time, the UE is performing a cell reselection at an LA border, the CN cannot in time obtain the updated
LA information about the UE which causes the paging to fail. The Seamless Paging feature enables the RNC to
perform cross-LA paging for a UE in idle mode as follows:
The RNC first pages the UE in the previous LA (indicated by LAC 1) in which the UE interacted with the
network. If the paging fails, the RNC pages the UE again in both the previous LA (LAC 1) and the neighboring
cells (belonging to other LAs indicated by LAC 2) of the previous LA's border cells.
Figure 2-1 Cross-LA paging
2.2 Benefits
The Seamless Paging feature increases the paging success rate of UEs at LA borders. The increase in the
paging success rate depends on UE behaviors and LA border coverage conditions.
3 Technical Description
The Seamless Paging feature is controlled by the EXTD_LAC_PAGING_SWITCH under the
PROCESSSWITCH5(BSC6900,BSC6910) parameter.
The RNC sends the first paging message and starts a paging response waiting timer if all the following
conditions are met:
The RNC receives a paging message with the cause value of "Terminating Conversational Call" from
the CN. This message carries the paging LA.
The UE to be paged is in idle mode.
If the RNC receives an RRC CONNECTION REQUEST message with the cause value of "Terminating
Conversational Call" or "Terminating - cause unknown" from the UE before the timer expires, the RNC
considers the paging successful. If the RNC does not receive any response from the UE before the timer
expires, the RNC re-pages the UE.
NOTE:
The default value of the paging response waiting timer is 2 n x 10 ms + 360. The value of n is the smaller
one between the value of the DRXCycleLenCoef(BSC6900,BSC6910) parameter in the ADD
4 Related Features
Prerequisite Features
None
Impacted Features
WRFD-150205 Layered Paging in Idle Mode
When the WRFD-150205 Layered Paging in Idle Mode feature and the WRFD-170104 Seamless Paging
feature are both enabled, the second-layer paging area in the former is the re-paging area in the latter.
5 Network Impact
System Capacity
When paging messages for UEs in idle mode are retransmitted for a fixed number of times, this feature reduces
the paging signaling traffic of UEs in idle mode and improves the system paging capacity.
When paging messages for UEs in idle mode are not retransmitted, this feature increases the paging signaling
traffic. When the cross-Iur seamless paging function is enabled, the number of increased pagings under the
local RNC is the sum of the number of failed CS first pagings under the local RNC and the number of failed CS
first pagings under neighboring cells (belonging to other LAs under the neighboring RNC) of previous LAs'
border cells.
Network Performance
If paging messages for UEs in idle mode are not retransmitted, paging retransmission under the latest LA
improves the paging success rate of mobile-terminated CS services. The increase in the paging success rate
depends on network coverage. Better coverage results in a larger increase in the paging success rate. If paging
messages for UEs in idle mode are retransmitted for a fixed number of times, paging retransmission under the
latest LA does not improve the paging success rate of mobile-terminated CS services.
The cross-LA paging function can increase the probability of successful mobile-terminated CS service pagings
for UEs at LA borders. The increase in successful mobile-terminated CS service pagings depends on the
proportion of moving UEs in LA border cells. A higher proportion of UEs in LA border cells results in a larger
increase in successful mobile-terminated CS service pagings.
According to the live network data analysis, the paging success rate of mobile-terminated CS services for UEs
in idle mode in an LA is about 95% in typical scenarios, and the proportion of CS service UEs in LA border cells
is about 20% of the total UEs in the network. Assume that 30% (which are obtained according to the soft
handover overhead in the live network) of CS service UEs are located in the overlapping coverage area of two
LA borders. Then, there is a 50% probability of cross-LA cell reselection.
In this scenario, if the Seamless Paging feature is enabled and paging messages for UEs in idle mode are not
retransmitted, it is predicted that:
The relative value of the paging success rate of mobile-terminated CS services for UEs in LA border
cells will increase by 20% to 40%.
The relative value of the paging success rate of mobile-terminated CS services for UEs in LA center
cells will increase by 5% to 20%.
The absolute value of the paging success rate of mobile-terminated CS services will increase by 0.25%
to 1%.
If paging messages for UEs in idle mode are retransmitted for a fixed number of times, cross-LA paging can
improve the paging success rate of mobile-terminated CS services for UEs in LA border cells. The relative value
of the paging success rate of mobile-terminated CS services will increase by 20% to 40%, and the absolute
value of the paging success rate will increase by 0.15% to 0.6%.
For the definition of soft handover overhead, see KPI Reference.
6 Engineering Guidelines
6.1 When to Use WRFD-170104 Seamless Paging
It is recommended that this feature should not be enabled if one LA has multiple RNCs. In other scenarios, this
feature can be enabled.
6.3 Deployment
6.3.1 Requirements
Other Features
See chapter 4 Related Features.
Hardware
None
License
6.3.3 Activation
6.3.3.1 Using MML Commands
1. Enable the WRFD-170104 Seamless Paging feature for the local RNC.
Run the RNC MML command SET URRCTRLSWITCH to set the EXTD_LAC_PAGING_SWITCH
under the PROCESSSWITCH5(BSC6900,BSC6910) parameter to on.
2. (Optional) If the neighboring RNC needs to support the WRFD-170104 Seamless Paging feature,
perform the following sub-steps to enable the cross-Iur seamless paging function:
a. On the neighboring RNC, run the RNC MML command SET URRCTRLSWITCH to set the
EXTD_LAC_PAGING_SWITCH under the PROCESSSWITCH5(BSC6900,BSC6910)
parameter to on.
b. On the local RNC, run the RNC MML command MOD UNRNC to set the
EXTD_LAC_PAGING_SUPPORT_SWITCH under the
FunctionSwitch(BSC6900,BSC6910) parameter to on and set NRncId to the ID of
the neighboring RNC.
c. On the neighboring RNC, run the RNC MML command MOD UNRNC to set the
EXTD_LAC_PAGING_SUPPORT_SWITCH under the
FunctionSwitch(BSC6900,BSC6910) parameter to on and set NRncId to the ID of
the local RNC.
You must perform a single configuration for a parameter before batch modifications of the parameter. You are
advised to perform batch modifications before logging out of the parameter setting interface.
1. Configure a single object on the CME. (CME single configuration)
Set parameters on the CME configuration interface according to the operation sequence described in
Table 6-2. For the method of performing the CME single configuration, see the CME Single
Configuration Operation Guide.
2. (Optional) Modify objects in batches on the CME. (CME batch modification center)
To modify objects, such as BSCs, BTSs, cells, and TRXs, in batches, click the
icon on the CME
configuration interface to start the batch modification wizard. For the method of performing batch
modifications through the CME batch modification center, press F1 on the wizard interface to obtain
online help.
Table 6-2 Configuring parameters on the CME
SN
URRCTRLSWITCH
UNRNC
6.3.5 Deactivation
6.3.5.1 Using MML Commands
1. Disable the WRFD-170104 Seamless Paging feature for the local RNC.
Run the RNC MML command SET URRCTRLSWITCH to set the EXTD_LAC_PAGING_SWITCH
under the PROCESSSWITCH5(BSC6900,BSC6910) parameter to off.
2. (Optional) Disable the cross-Iur seamless paging function.
a. On the neighboring RNC, run the RNC MML command SET URRCTRLSWITCH to set the
EXTD_LAC_PAGING_SWITCH under the PROCESSSWITCH5(BSC6900,BSC6910)
parameter to off.
b. On the local RNC, run the RNC MML command MOD UNRNC to set the
EXTD_LAC_PAGING_SUPPORT_SWITCH under the
FunctionSwitch(BSC6900,BSC6910) parameter to off and set NRncId to the ID of
the neighboring RNC.
c. On the neighboring RNC, run the RNC MML command MOD UNRNC to set the
EXTD_LAC_PAGING_SUPPORT_SWITCH under the
URRCTRLSWITCH
2 (optional)
UNRNC
The VS.ExtdPaging1.Succ.Idle.CS counter indicates the number of times that UEs in idle mode receive crossLAC paging messages and send paging responses successfully, that is, the number of successful seamless
pagings.
PCH Congestion
If the re-paging message is delivered in the neighboring LAs but the PCH is congested, Uu resources for
transmitting the re-paging messages are preempted. Therefore, the value of the
VS.RRC.Paging1.Loss.PCHCong.Cell counter increases.
Iur Traffic
If the cross-Iur seamless paging function is enabled, Iur traffic increases, that is, the value of the
VS.SRNCIurBytesSigDCH.Tx counter increases.
6.6 Troubleshooting
None
7 Parameters
Table 7-1 Parameters
Para
mete
r ID
NE
PRO BSC6
CES 900
SSW
ITCH
5
MML
Command
Feature
ID
SET
WRFDURRCTRLS 170202
WITCH
WRFD170201
WRFD150252
WRFD150253
WRFD170104
WRFD171201
WRFD171202
WRFD150255
WRFD150254
Feature Name
Description
TCP Proxy
Seamless Crystal Voice
Video Service Rate
Adaption
VoIP Application
Management
Seamless Paging
Crystal Voice in Deep
Coverage
Ultrafast CS Call Setup
Differentiated Service
Based on Terminal
Differentiated Service
Based on Application
Resource Reservation
Meaning:
1)INTERRAT_LOAD_SINGLE_RPT_FOR_
LTE_SWITCH(RIM-based and Requestbased Load Information Sharing Switch)
Whether a UMTS cell sends its load
information to an LTE cell through the RIM
procedure after receiving a load information
sharing request from the LTE cell.
1: This switch is turned on. UMTS cells
support the RIM-based load information
sharing function. A UMTS cell sends its load
information to an LTE cell after receiving a
load information sharing request from the
LTE cell.
0: This switch is turned off. UMTS cells do
not support the RIM-based load information
sharing function. A UMTS cell does not
respond to the load information sharing
request from an LTE cell.
2)INTERRAT_LOAD_REPORT_FROM_LT
E_SWITCH(Learning LTE Load Through
RIM Switch)
Whether the RNC obtains the load
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
specified by "NonHLoadStateForP2D" or
enters a lighter state. The values of the
"ActualloadStateForP2D" and
"NonHLoadStateForP2D" parameters can
be queried by running the RNC MML
command "LST UUESTATETRANS".
(2) The Ec/N0 is greater than or equal to
"P2DEcNoThd". The value of the
"P2DEcNoThd" parameter can be queried
by running the RNC MML command "LST
UFRC".
0: Indicates that this switch is set to OFF.
The RNC triggers P2F state transitions, not
load- and Ec/N0-based P2D state
transitions.
21)PRIMOPER_NONROAM_USER_CN_S
A_SWITCH
Whether the CN-initiated service awareness
function applies only to non-roaming UEs of
the primary operator.
1: Indicates that this switch is set to ON.
The CN-initiated service awareness
function applies only to non-roaming UEs of
the primary operator.
0: Indicates that this switch is set to OFF.
The CN-initiated service awareness
function applies to all UEs.
22)PS_R99_BLER_STAT_OPT_SWITCH(O
ptimize The Measurement of PS R99
BLER)
Whether the RNC optimizes the
measurement of the block error rate (BLER)
for PS R99 services.
1: Indicates that this switch is set to ON.
The RNC identifies erroneous blocks
generated by false detections during PS
R99 D2F and F2D state transitions and
during soft handovers and does not
calculate these blocks into the PS R99
BLER.
0: Indicates that this switch is set to OFF.
The RNC calculates the preceding
erroneous blocks into the PS R99 BLER.
23)STATE_FACH_CONSISTENT_OPTI_S
WITCH(CELL_FACH UE State Consistency
Optimization Switch )
Whether to enable the state consistency
optimization algorithm for UEs in the
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
CELL_FACH state.
1: Indicates that this switch is set to ON.
The state consistency optimization
algorithm is enabled for UEs in the
CELL_FACH state. The RNC waits for a
certain period of time if it does not receive
any response from the UE in the
CELL_FACH state. This prevents state
inconsistencies between the RNC and UE
caused by UE not receiving an RRC
CONNECTION RELEASE message.
0: Indicates that this switch is set to OFF.
The state consistency optimization
algorithm is disabled for UEs in the
CELL_FACH state.
This switch is set to OFF by default.
24)D2P_RECFG_REEST_SWITCH(D2P
Reconfiguration and Reestablishment
Switch)
Whether the RNC triggers a D2P
reconfiguration and reestablishment
procedure for fast dormancy UEs that have
experienced a TRB reset or an uplink RL
synchronization failure.
1: Indicates that this switch is set to ON.
The RNC triggers a D2P reconfiguration
and reestablishment procedure for fast
dormancy UEs that have experienced a
TRB reset or uplink RL synchronization
failure.
0: Indicates that this switch is set to OFF.
The RNC does not trigger a D2P
reconfiguration and reestablishment
procedure for fast dormancy UEs in the
preceding scenario.
This switch is set to OFF by default.
GUI Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LT
E_SWITCH,
INTERRAT_LOAD_REPORT_FROM_LTE_
SWITCH, UL_EVQI_SWITCH,
DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH
, APP_GRP_RES_RSV_SWITCH,
RIM_ON_ECO_SWITCH,
PRIMOPER_NONROAM_USER_CN_SA_
SWITCH,
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
SRBCHG_DRD_FAST_RB_SETUP_SWIT
CH,
SRBNOCHG_DRD_FAST_RB_SETUP_S
WITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_
SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITC
H, EXTD_LAC_PAGING_SWITCH,
TCP_PROXY_SWITCH,
SEAMLESS_CRYSTAL_VOICE_SWITCH,
CS_RB_PRI_MC_SWITCH,
L2U_SRVCC_PS_TIMEOUT_CS_RELOC_
IN_SWITCH,
CRYSTAL_VOICE_DEEPCOVER_SWITCH
, LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWIT
CH, D2P_RECFG_REEST_SWITCH
Unit: None
Actual Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LT
E_SWITCH,
INTERRAT_LOAD_REPORT_FROM_LTE_
SWITCH,
UL_EVQI_SWITCH,
DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH
,
APP_GRP_RES_RSV_SWITCH,
RIM_ON_ECO_SWITCH,
PRIMOPER_NONROAM_USER_CN_SA_
SWITCH,
SRBCHG_DRD_FAST_RB_SETUP_SWIT
CH,
SRBNOCHG_DRD_FAST_RB_SETUP_S
WITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_
SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITC
H,
EXTD_LAC_PAGING_SWITCH,
TCP_PROXY_SWITCH,
SEAMLESS_CRYSTAL_VOICE_SWITCH,
CS_RB_PRI_MC_SWITCH,
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
L2U_SRVCC_PS_TIMEOUT_CS_RELOC_
IN_SWITCH,
CRYSTAL_VOICE_DEEPCOVER_SWITCH
,
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWIT
CH,
D2P_RECFG_REEST_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT_FOR_LT
E_SWITCH:0,INTERRAT_LOAD_REPORT
_FROM_LTE_SWITCH:0,UL_EVQI_SWITC
H:0,DL_EVQI_SWITCH:0,VIDEO_RATE_A
DAPTION_SWITCH:0,VOIP_MANAGE_SW
ITCH:0,DIFF_SERVICE_ON_TERMINAL_S
WITCH:0,APP_GRP_RES_RSV_SWITCH:
0,RIM_ON_ECO_SWITCH:0,PRIMOPER_
NONROAM_USER_CN_SA_SWITCH:0,SR
BCHG_DRD_FAST_RB_SETUP_SWITCH:
0,SRBNOCHG_DRD_FAST_RB_SETUP_S
WITCH:0,FACH_RB_RECFG_FAIL_SPEC_
CAUSE_SWITCH:0,WBAMR_HHO_FAIL_
ROLLBACK_SWITCH:0,EXTD_LAC_PAGI
NG_SWITCH:0,TCP_PROXY_SWITCH:0,S
EAMLESS_CRYSTAL_VOICE_SWITCH:0,
CS_RB_PRI_MC_SWITCH:0,L2U_SRVCC
_PS_TIMEOUT_CS_RELOC_IN_SWITCH:
0,CRYSTAL_VOICE_DEEPCOVER_SWIT
CH:0,LOAD_BASED_P2D_SWITCH:0,PS_
R99_BLER_STAT_OPT_SWITCH:0,STATE
_FACH_CONSISTENT_OPTI_SWITCH:0,D
2P_RECFG_REEST_SWITCH:0
PRO BSC6
CES 910
SSW
ITCH
5
SET
WRFDURRCTRLS 170202
WITCH
WRFD170201
WRFD150252
WRFD150253
WRFD170104
WRFD171201
WRFD171202
TCP Proxy
Seamless Crystal Voice
Video Service Rate
Adaption
VoIP Application
Management
Seamless Paging
Crystal Voice in Deep
Coverage
Ultrafast CS Call Setup
Differentiated Service
Based on Terminal
Differentiated Service
Meaning:
1)INTERRAT_LOAD_SINGLE_RPT_FOR_
LTE_SWITCH(RIM-based and Requestbased Load Information Sharing Switch)
Whether a UMTS cell sends its load
information to an LTE cell through the RIM
procedure after receiving a load information
sharing request from the LTE cell.
1: This switch is turned on. UMTS cells
support the RIM-based load information
sharing function. A UMTS cell sends its load
information to an LTE cell after receiving a
load information sharing request from the
LTE cell.
Para
mete
r ID
NE
MML
Command
Feature
ID
WRFD150255
WRFD150254
Feature Name
Based on Application
Resource Reservation
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
6) VOIP_MANAGE_SWITCH (VoIP
Application Management Switch)
Whether the VoIP application management
function is enabled.
1: This switch is turned on. VoIP application
management actions are performed on PS
UEs that are processing VoIP services.
VoIP application management actions can
either be VoIP application rate ensurance or
VoIP application speed limit.
0: This switch is turned off. the VoIP
application management function is
disabled for PS UEs.
7)
DIFF_SERVICE_ON_TERMINAL_SWITCH
(Differentiated Service Based on Terminal
Switch)
Whether the Differentiated Service Based
on Terminal feature is enabled.
1: This switch is turned on. PS UEs
processing BE services are grouped into
different terminal groups based on their type
approval codes (TACs) in IMEIs, and each
terminal group is assigned an SPI weight
for BE services, thereby achieving
differentiated services.
0: This switch is turned off. The
Differentiated Service Based on Terminal
feature is disabled for PS UEs processing
BE services.
8) APP_GRP_RES_RSV_SWITCH
(Differentiated Service Based on Application
Resource Reservation Switch)
Whether the Differentiated Service Based
on Application Resource Reservation
feature is enabled.
1: This switch is turned on. The RNC
identifies service types, maps different
service types to different resource groups,
and configure different resource reservation
policies for these resource groups. In this
way, resource reservation is performed
based on service types.
0: This switch is turned off. The RNC does
not reserve resources based on service
types or service groups.
9)RIM_ON_ECO_SWITCH(Support RIM by
eCoordinator Switch)
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
SWITCH, UL_EVQI_SWITCH,
DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH
, APP_GRP_RES_RSV_SWITCH,
RIM_ON_ECO_SWITCH,
PRIMOPER_NONROAM_USER_CN_SA_
SWITCH,
SRBCHG_DRD_FAST_RB_SETUP_SWIT
CH,
SRBNOCHG_DRD_FAST_RB_SETUP_S
WITCH,
FACH_RB_RECFG_FAIL_SPEC_CAUSE_
SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITC
H, EXTD_LAC_PAGING_SWITCH,
TCP_PROXY_SWITCH,
SEAMLESS_CRYSTAL_VOICE_SWITCH,
CS_RB_PRI_MC_SWITCH,
L2U_SRVCC_PS_TIMEOUT_CS_RELOC_
IN_SWITCH,
CRYSTAL_VOICE_DEEPCOVER_SWITCH
, LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWIT
CH, D2P_RECFG_REEST_SWITCH
Unit: None
Actual Value Range:
INTERRAT_LOAD_SINGLE_RPT_FOR_LT
E_SWITCH,
INTERRAT_LOAD_REPORT_FROM_LTE_
SWITCH,
UL_EVQI_SWITCH,
DL_EVQI_SWITCH,
VIDEO_RATE_ADAPTION_SWITCH,
VOIP_MANAGE_SWITCH,
DIFF_SERVICE_ON_TERMINAL_SWITCH
,
APP_GRP_RES_RSV_SWITCH,
RIM_ON_ECO_SWITCH,
PRIMOPER_NONROAM_USER_CN_SA_
SWITCH,
SRBCHG_DRD_FAST_RB_SETUP_SWIT
CH,
SRBNOCHG_DRD_FAST_RB_SETUP_S
WITCH,
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
FACH_RB_RECFG_FAIL_SPEC_CAUSE_
SWITCH,
WBAMR_HHO_FAIL_ROLLBACK_SWITC
H,
EXTD_LAC_PAGING_SWITCH,
TCP_PROXY_SWITCH,
SEAMLESS_CRYSTAL_VOICE_SWITCH,
CS_RB_PRI_MC_SWITCH,
L2U_SRVCC_PS_TIMEOUT_CS_RELOC_
IN_SWITCH,
CRYSTAL_VOICE_DEEPCOVER_SWITCH
,
LOAD_BASED_P2D_SWITCH,
PS_R99_BLER_STAT_OPT_SWITCH,
STATE_FACH_CONSISTENT_OPTI_SWIT
CH,
D2P_RECFG_REEST_SWITCH
Default Value:
INTERRAT_LOAD_SINGLE_RPT_FOR_LT
E_SWITCH:0,INTERRAT_LOAD_REPORT
_FROM_LTE_SWITCH:0,UL_EVQI_SWITC
H:0,DL_EVQI_SWITCH:0,VIDEO_RATE_A
DAPTION_SWITCH:0,VOIP_MANAGE_SW
ITCH:0,DIFF_SERVICE_ON_TERMINAL_S
WITCH:0,APP_GRP_RES_RSV_SWITCH:
0,RIM_ON_ECO_SWITCH:0,PRIMOPER_
NONROAM_USER_CN_SA_SWITCH:0,SR
BCHG_DRD_FAST_RB_SETUP_SWITCH:
0,SRBNOCHG_DRD_FAST_RB_SETUP_S
WITCH:0,FACH_RB_RECFG_FAIL_SPEC_
CAUSE_SWITCH:0,WBAMR_HHO_FAIL_
ROLLBACK_SWITCH:0,EXTD_LAC_PAGI
NG_SWITCH:0,TCP_PROXY_SWITCH:0,S
EAMLESS_CRYSTAL_VOICE_SWITCH:0,
CS_RB_PRI_MC_SWITCH:0,L2U_SRVCC
_PS_TIMEOUT_CS_RELOC_IN_SWITCH:
0,CRYSTAL_VOICE_DEEPCOVER_SWIT
CH:0,LOAD_BASED_P2D_SWITCH:0,PS_
R99_BLER_STAT_OPT_SWITCH:0,STATE
_FACH_CONSISTENT_OPTI_SWITCH:0,D
2P_RECFG_REEST_SWITCH:0
Func BSC6
tionS 900
witch
ADD
UNRNC
MOD
UNRNC
WRFD010615
WRFD170104
WRFD-
Multiple RAB
Package(PS RAB >= 2)
Seamless Paging
Interactive QoS Class
Background QoS Class
Meaning:
1)EXTD_LAC_PAGING_SUPPORT_SWIT
CH(Neighbor RNC Support Extended LAC
Paging Switch)
whether the neighboring RNC supports the
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
010503
WRFD010504
Func BSC6
tionS 910
witch
ADD
UNRNC
MOD
UNRNC
WRFD010615
WRFD170104
WRFD010503
WRFD010504
Description
Meaning:
1)EXTD_LAC_PAGING_SUPPORT_SWIT
CH(Neighbor RNC Support Extended LAC
Paging Switch)
whether the neighboring RNC supports the
extended LAC paging function.
1: This switch is set to on. The SRNC can
send paging messages to the neighboring
RNC.
0: This switch is set to off. The SRNC
cannot send paging messages to the
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
neighboring RNC.
2)AMBR_SUPPORT_SWITCH(NRNC
Support AMBR)
Whether the SRNC sends a neighboring
RNC an information element (IE) that
contains the aggregate maximum bit rate
(AMBR).
1: Indicates that this switch is set to ON.
The SRNC sends an IE that contains the
AMBR to the DRNC over the Iur interface
during an inter-RNC handover.
0: Indicates that this switch is set to OFF.
The SRNC does not send an IE that
contains the AMBR to the DRNC over the
Iur interface during an inter-RNC handover.
GUI Value Range:
EXTD_LAC_PAGING_SUPPORT_SWITCH
(EXTD_LAC_PAGING_SUPPORT_SWITC
H),
AMBR_SUPPORT_SWITCH(AMBR_SUPP
ORT_SWITCH)
Unit: None
Actual Value Range:
EXTD_LAC_PAGING_SUPPORT_SWITCH
,
AMBR_SUPPORT_SWITCH
Default Value:
EXTD_LAC_PAGING_SUPPORT_SWITCH
:0,AMBR_SUPPORT_SWITCH:0
Macc BSC6
Page 900
Repe
atTim
es
SET
UDPUCFG
DATA
WRFD010301
Paging UE in Idle,
CELL_PCH, URA_PCH
State (Type 1)
Macc BSC6
Page 910
Repe
atTim
es
SET
UDPUCFG
DATA
WRFD010301
Paging UE in Idle,
CELL_PCH, URA_PCH
State (Type 1)
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
BSC6
900
ADD
UCNDOMAI
N
MOD
UCNDOMAI
N
WRFD150205
WRFD010401
WRFD140206
Meaning:
Discontinuous Reception (DRX) cycle
length coefficient of the CN domain, which
is broadcast in SIB1 and used by UEs in the
idle mode.
This parameter is an advanced parameter
and must be modified only with the
assistance of Huawei technical support
personnel.
GUI Value Range: 6~9
Unit: None
Actual Value Range: 6~9
Default Value: 6
DRX
Cycl
eLen
Coef
BSC6
910
ADD
UCNDOMAI
N
MOD
UCNDOMAI
N
WRFD150205
WRFD010401
WRFD140206
Meaning:
Discontinuous Reception (DRX) cycle
length coefficient of the CN domain, which
is broadcast in SIB1 and used by UEs in the
idle mode.
This parameter is an advanced parameter
and must be modified only with the
assistance of Huawei technical support
personnel.
GUI Value Range: 6~9
Unit: None
Actual Value Range: 6~9
Default Value: 6
SET UFRC
WRFD010302
WRFD010301
WRFD150205
Paging UE in
CELL_FACH,
CELL_DCH State (Type
2)
Paging UE in Idle,
CELL_PCH, URA_PCH
State (Type 1)
Layered Paging in Idle
Mode
DrxC BSC6
ycleL 900
enCo
ef
Para
mete
r ID
NE
MML
Command
Feature
ID
Feature Name
Description
SET UFRC
WRFD010302
WRFD010301
WRFD150205
Paging UE in
CELL_FACH,
CELL_DCH State (Type
2)
Paging UE in Idle,
CELL_PCH, URA_PCH
State (Type 1)
Layered Paging in Idle
Mode
8 Counters
Table 8-1 Counters
Counter ID
Counter Name
Counter
Description
NE
Feature ID
Feature
Name
73429229
VS.ExtdPaging1.Att.Idle.CS
Number of
BSC6900
Extended
Paging
Attempts
Triggered by
CS
Conversationa
l Services to
Page UEs in
Idle Mode for
RNC
WRFD170104
WRFD010301
Seamless
Paging
Paging UE in
Idle,
CELL_PCH,
URA_PCH
State (Type
1)
73429229
VS.ExtdPaging1.Att.Idle.CS
Number of
BSC6910
Extended
Paging
Attempts
Triggered by
CS
Conversationa
l Services to
Page UEs in
Idle Mode for
WRFD170104
WRFD010301
Seamless
Paging
Paging UE in
Idle,
CELL_PCH,
URA_PCH
State (Type
1)
Counter ID
Counter Name
Counter
Description
NE
Feature ID
Feature
Name
RNC
73429231
VS.ExtdPaging1.Succ.Idle.CS
Number of
BSC6900
Successful
Extended
Pagings
Triggered by
CS
Conversationa
l Services to
Page UEs in
Idle Mode for
RNC
WRFD170104
WRFD010301
Seamless
Paging
Paging UE in
Idle,
CELL_PCH,
URA_PCH
State (Type
1)
73429231
VS.ExtdPaging1.Succ.Idle.CS
Number of
BSC6910
Successful
Extended
Pagings
Triggered by
CS
Conversationa
l Services to
Page UEs in
Idle Mode for
RNC
WRFD170104
WRFD010301
Seamless
Paging
Paging UE in
Idle,
CELL_PCH,
URA_PCH
State (Type
1)
73429236
VS.ExtdPaging1.Att.Idle.CS.DRN
C
Number of
BSC6900
Extended
Paging
Attempts
Triggered by
CS
Conversationa
l Services to
Page UEs in
Idle Mode
over the Iur
Interface for
DRNC
WRFD170104
WRFD010301
Seamless
Paging
Paging UE in
Idle,
CELL_PCH,
URA_PCH
State (Type
1)
73429236
VS.ExtdPaging1.Att.Idle.CS.DRN
C
Number of
BSC6910
Extended
Paging
Attempts
Triggered by
CS
Conversationa
l Services to
Page UEs in
Idle Mode
over the Iur
WRFD170104
WRFD010301
Seamless
Paging
Paging UE in
Idle,
CELL_PCH,
URA_PCH
State (Type
1)
Counter ID
Counter Name
Counter
Description
Interface for
DRNC
NE
Feature ID
Feature
Name