Professional Documents
Culture Documents
General information
Material specifications
X-HVB
Carbon steel:
Zinc coating:
127.5
142.5
X-HVB 125
2.5
2.5
20.6
31
63
63
20.6
31
51
63
X-HVB 95
112.5
X-HVB 110
X-ENP-21 HVB
Carbon steel shank: HRC58
Zinc coating:
816 m
Tool
DX 76
Fastener guide
X-76-F-HVB X-76-F-HVB-PTR
Piston
X-76-P-HVB X-76-P-HVB-PTR
Cartridges
95
51
20.6
31
51
Rm = 295350 N/mm2
3 m
24.3
50
60
DX 76 PTR
50
X-HVB 40
24.3
88
X-ENP-21 HVB
43
7.4
2
52
24.3
50
60
DIBt (Germany)
MLIT / BCJ (Japan),
80
SOCOTEC (France)
X-HVB 50
X-HVB 80
TZS (Czech)
Note: technical data presented in these approvals and
design guidelines reflect specific local conditions and
may differ from those published in this handbook.
If the fastening is subject to an approval process or
where a design guideline must be used, technical
data in the approval or design guideline has precedence over data presented here. Approval copies are
available from your Hilti technical advisory service.
99
25.8
24.3
50
4.5
15
06 / 2015
111
X-HVB
Applications
Examples
Typical application of
X-HVB shear connector
with steel deck, e.g. new
construction.
C
Typical application of
X-HVB shear connector
with jack arch system
(without steel deck), e.g.
rehabilitation project.
Design data
Designation
LWC 1) / NWC 2)
X-HVB 40
LWC
X-HVB 40
NWC
X-HVB 50
X-HVB 50
X-HVB 80
X-HVB 95
X-HVB 110
X-HVB 125
X-HVB 140
1)
2)
3)
4)
5)
LWC
NWC
NWC
NWC
NWC
NWC
NWC
Characteristic shear
resistance, PRk 3)
Allowable
horizontal shear 5)
25 kN
20 kN
N.A.
25 kN
28 kN
28 kN
28 kN
35 kN
35 kN
35 kN
35 kN
20 kN
23 kN
23 kN
23 kN
28 kN
28 kN
28 kN
28 kN
N.A.
N.A.
N.A.
14 kN
17.5 kN
17.5 kN
17.5 kN
17.5 kN
112
06 / 2015
X-HVB
1 x 1,25
b0
kt = K b0 hschap
Nr
hap
hap
EN 1994-1-1 designs:
K = 0.70
Nr = X-HVBs / rib ( 2 in the calculation even if 3 are placed
in a rib)
Note: kt 1.0
for
b0
1.8 kp = 1.0
hap
for
b0
b
h h
< 1.8 kp = 0.6 x 0 sc ap
hap
hap
hap
Note: kp 1.0
06 / 2015
113
X-HVB
Engineering advice
Connector placement along the beam
The X-HVB is a flexible connector and may be uniformly distributed between critical sections.
These critical sections, where large changes in shear flow occur, may be at supporting points,
points of application of point loads or areas with extreme bending moments.
114
06 / 2015
X-HVB
Application requirements
Thickness of base material
1 x 1.25
or
or
Position the X-HVBs so that the shear force is transferred symmetrically to the beam.
X-HVB orientation parallel to the axis of the beam is preferred.
Positioning on metal decks - ribs transverse to beam
1) One, two or three X-HVBs per rib
Parallel to beam
06 / 2015
Perpendicular to beam
115
X-HVB
2a) Position in the rib : 1 X-HVB per rib leg centred in the rib or 40 mm clearance
=
40 mm
2b) With 2 or 3 X-HVBs per rib legs centred in the rib or alternated about the center
=
50 mm
m = rib spacing
4 hc
600 mm
100 mm
hc
50 mm
hc
With 1 connector per row, alternate direction of connectors from X-HVB to X-HVB.
In case of multiple rows (parallel to the beam axis), X-HVBs must be placed with the same
direction inside of each row and alternate from row to row.
116
06 / 2015
X-HVB
Corrosion information
The intended use only comprises fastenings which are not directly exposed to external
weather conditions or moist atmospheres.
Application limits
Application limits are valid only if correct cartridge and power setting are used!
Application limits X-ENP-21 HVB
>20
>20
10
10
18
16
15
14
13
17
Applicable
range of base
materials
12
11
10
9
8
7
S 235
S 275
S 355
6
350 400 450 500 550 600 650 700 750
Steel strength, Rm [N/mm2]
06 / 2015
18
17
16
15
14
Black 4
from
10 mm
Black 4
from
10 mm
13
12
11
10
9
8
Red 4
S 235
Black 3
Black 2
S 355
117
X-HVB
1 x 1,25
b0
8 mm
hap
hsc
hc
Fastener selection
b0
Connector
Designation
Item no.
X-HVB 40
2112256
X-HVB 50
56467
X-HVB 80
239357
45
45
X-HVB 95
348179
60
57
X-HVB 110
348180
75
66
X-HVB 125
348181
80
75
X-HVB 140
348321
80
80
283512
X-HVB
Metal decking
Structural steel
118
06 / 2015