You are on page 1of 53

IDTECK

The Company Leads High Security

Star Icon-100
Software Manual V2.6

Software Manual

Star Icon-100 Manual V2.6 (English) -1-

IDTECK

The Company Leads High Security

Contents
1.

Installation.
1.1 Require of Hardware
1.2 Require of Software
1.3 Installation

2.

Configuration.
2.1 Run Program
2.2 Configuration 1(Setup Wizard)
2.3 Configuration 2(Manual)
2.4 Configuration 3(System Definition)

3.

Interface.
3.1 Main Window
3.2 Detail Main Window
3.3 Menu

4.

Controller

Database

Status

Report

View

About

Operation.
4.1 Controller
z

Set Communication

Set System Time

Holiday Definition

Timeschedule Definition

Input/Output Definition

Set Reader Mode

Reader Status

4.2 Database
z

Company Definition

Title(Positon) Definition

Software Manual

Star Icon-100 Manual V2.6 (English) -2-

IDTECK

The Company Leads High Security


z

Department Definition

Card Type Definition

System Definition

Access Group Definition

Card Holder

Database Backup / Restore

Login ID & Password Definition

Option

4.3 Status
z

Door Control & Status

Event Status

Alarm Status

Communication Status

4.4 Report
z

Card List Report

Event Report

Alarm Report

4.5 View
z

Vertical

Horizontal

4.6 About
z

Program Information

Software Manual

Star Icon-100 Manual V2.6 (English) -3-

IDTECK

The Company Leads High Security

Start Program
Login : admin

Log in at the administrator level

Controller -> Setup Wizard


or
Controller -> Set Communication

Password : None

Software Configuration by
Setup wizard or Manual.

Define Star Icon-100 System

Database -> System Definition

address and system


information.

Controller -> Timeschedule Definition

Database -> Company Definition.

Database -> Title(Position) Definition.

Database -> Department Definition.

Database -> Card Type Definition.

Database -> Access Group Definition.

Database -> Card Holder

Software Manual

Define Timecode.

Define Company List.

Define Title List.

Define Department List.

Define Access Card Type.


Define Access Group

(Reader + TimeCode).
Register Card No. to system.

Star Icon-100 Manual V2.6 (English) -4-

IDTECK

The Company Leads High Security

1. Program Installation
Operating environments of Star Icon-100 Program.
1.1 Require of Hardware.
O/S : Windows 98, Windows ME, Windows NT, Windows 2000
RAM : 64MB or higher
CPU : Pentium II 450 or higher
Hard disk : program installation space(50MB), data storage space(500MB or higher, free space change by
the number of data outbreak at any time
1.2 Require of Software (option)
Microsoft Office 97 or 2000 : Access 97(recommendation), Access 2000
1.3 Installation

Insert Setup/Installation CD in the CD-ROM drive. Open CD-ROM Star Icon-100 setup folder in the
Windows Explorer. Execute Setup.exe

Click Next > button.

Software Manual

Star Icon-100 Manual V2.6 (English) -5-

IDTECK

The Company Leads High Security


z

Designate directory/folder to store the program. When selecting a different location for program folder,
click Browse button. If you are installing the program in the default directory/folder, click Next >
button.

Select a folder in the Program Folder. Use the defaulted name. Click Next > button .

Software Manual

Star Icon-100 Manual V2.6 (English) -6-

IDTECK

The Company Leads High Security


Click Next > button.

Start to install the program files in Hard disk.

Setup is finished. If you restart your computer, select Yes, I want to restart my computer now and
didnt restart, select No, I will restart my computer later. Then click Finish button.

Software Manual

Star Icon-100 Manual V2.6 (English) -7-

IDTECK

The Company Leads High Security

Reference: Problems while installing program


Upon completion of installing, restart system occasionally. If restart
option is appeared, restart system.
When this program is installed at Windows NT 4.0 or Windows
2000, can be appeared caution. At this time, restart system, then
program is executed without problem.
file(s) failed to self register:
C:\WINNT\System32\Comcat.dll

Software Manual

Star Icon-100 Manual V2.6 (English) -8-

IDTECK

The Company Leads High Security

2. Configuration
To use this program, need to set some environments. Between program and Star Icon-100 system,
communication environment setting and system (reader) registration must set to communicate with between
system and program.
2.1 Run Program
z

Click StartProgram STARICON100(English Edition) STARICON100(English Edition).

Log-in procedure
Defaulted User ID is admin without password. Thus, press ENTER or click Login to start.

2.2 Configuration 1 (Using Setup Wizard)


After installing the program setup, some setting to operate program is required at first. Though a manual
form is used to set it, Setup Wizard is usually used by the basic setup level.

Click Controller Setup Wizard in menu, then the following screen executes. Step 1 is company
definition. After inputting defaulted Company Code, input Company Name. Click Next >> button to move
step 2.

Software Manual

Star Icon-100 Manual V2.6 (English) -9-

IDTECK

The Company Leads High Security

Step 2 is Set Communication. Select Serial chain.

Step 3 is Set Port. If Serial Port (Com1) is used, select COM1 and Serial Port (Com2) is used, select COM2.
Click Next>> button.

Software Manual

Star Icon-100 Manual V2.6 (English) -10-

IDTECK

The Company Leads High Security

Step 4 is Set Speed. The defaulted communication speed in system (Star Icon-100) is 9600BPS. Select
9600BPS. Click Next>> button.

Step 5 is Select system address. Select Start Address and End Address in installed system (Star Icon-100)
reader. Click Next>> button.
For example, if five Star Icon100 systems are installed, reader address is set 01,02,03,04,05 or
00,01,02,03, 04 usually. Then you can select Start Address from 00 or 01 and End Address to 04 or 05.

Software Manual

Star Icon-100 Manual V2.6 (English) -11-

IDTECK

The Company Leads High Security

Step 6 is Communication status Test of selected system (Star Icon-100) reader address from Start Address to
End Address. Click Test button, then will show following screen. If communication is correct, you will see
a message Communication OK or Communication Error.

Reference: Communication Error


Indicating Communication Error, identify Communication port or
communication speed and system address whether to set correctly. If you
find no errors, need to check communication lines.

Software Manual

Star Icon-100 Manual V2.6 (English) -12-

IDTECK
z

The Company Leads High Security


Upon completion of above set up procedures, click Complete button, then following message will appear.
When the system completes the setup, you must restart program. If select message Yes, program restart or
exit setup wizard.

2.3 Configuration 2 (Set Communication)


Communication speed and communication port must be set in order to communicate with between Star
Icon-100 system and installed program in computer by serial communication (RS232C).
z

Click Controller -> Set Communication in menu.

Comm Port set communication port connected between Star Icon-100 system and computer. Defaulted
value is COM1.

Baud Rate set communication speed .between Star Icon-100 system and computer. Defaulted value is
9600bps.

Parity Bit, Data Bit, Stop Bit use defaulted value.

When communication setup is completed, click OK button to save, then Close button to exit.

Software Manual

Star Icon-100 Manual V2.6 (English) -13-

IDTECK

The Company Leads High Security


Reference: Default Button
Default Button set all value defaulted. Communication port is COM1,
Communication speed is 9600, Parity bit is NONE', Data bit is 8 BIT,
Stop bit is 1 BIT. Usually, not change a basic value, uses defaulted
value.

2.4 Configuration 3 (System Definition)


Registers information of Star Icon-100 system.
System definition is set both system address and system information in installed system. System address
must be checked because system and program communicate with each other as system address.
(Certification of system address refer to hardware (system) manual.)
z

Click Database System Definition in menu.

System Address selects the same address of Star Icon-100 system.


Usually to use one Star Icon-100 system, System Address is 00 or 01. To use several Star Icon-100
systems simultaneously, System Address is particularly set each system.

System Name is the name of Star Icon-100 system.

System Location selects location (floor in a building) of installed Star Icon-100 system.

Contact Type selects Door Contact type installed Door Lock. By the Contact type, checks the gate
status.

Enter the name of First Reader, Second Reader.


Also when a reader places the gate of coming in, it is the entry reader. Then selects IN. When a reader
places the gate of going out, it is exit reader. Then selects OUT.

Click Save button to save.

Software Manual

Star Icon-100 Manual V2.6 (English) -14-

IDTECK

The Company Leads High Security


z

Click Delete button after selecting the reader you want to delete on the right Reader (Door) List.

Reference: Restart Program


Upon completion of communication environment setting and
System Definition setting, exit program and restart program.
It is that applies setting information to Star Icon-100 system and
program again. So, after exiting, must restart program to apply to
modified value.

Reference: Problem of communication


Identify status of communication through Communication Status
after restarting program.
If setting is finished correctly, you identify communication status of
Star Icon-100 like following figure.

* Not Communicate
1.

When system isnt communicated, repeat previous procedures


(Configuration).

2.

Identify whether address of Star Icon-100 device and program


are equal.

3.

Identify whether Communication port of between Star Icon-100


system and computer are equal.

4.

Check a Converter whether to turn on or off power and to have


matters when used Converter (RS422 -> RS232).

Software Manual

Star Icon-100 Manual V2.6 (English) -15-

IDTECK

The Company Leads High Security

3. Interface
Following Figure shows the menu and functions of Star Icon-100.
3.1 Main Window
When program executes, following figure will show. The main screen will show Event Status and Alarm
Status at once.
Menu

Quick Icons

Event Status

Alarm Status

Login

3.2 Detail Main Window


z

Menu : Gather menu executed each function for program operation.

Quick Icon : Gather Icon used frequently.

Login : Shows Login ID and Login time.

Event Status : Show Access Granted, Exit events.

Alarm Status : Show Access Denied, Timeschedule error, Antipassback, sensor, contact, fire, Tamper
events.

Software Manual

Star Icon-100 Manual V2.6 (English) -16-

IDTECK

The Company Leads High Security

3.3 Menu
z

Controller
Gather menu of Star Icon-100 system control and functions related system.

Set Communication: Use to communicate with

between Star Icon-100 system and PC

(computer).
-

Set Time : Set date and time.

Holiday Definition: After inputting holiday date, transmit to Star Icon-100 system. Then apply to
a holiday.

Time Schedule Definition : Set Time Schedule by day, by holiday.

Input/Output Definition : After setting the input/output point of contact, transmit to Star Icon100 system.

Reader Mode Definition : Change Reader Mode of Star Icon-100 system. In Star Icon-100
system, use RF Only or RF + Password. Also set use keypad enable or disable.

Antipassback Definition : Decide whether to use or not a Antipassback mode. This function is
optional when to set additional reader (Second reader). Also, can use software and use global
antipassback function.

Duress Mode Definition : In emergency, after user inputs registered 2-digit password in advance,
read card. Then, Duress mode is operated, so inform alarm status according to registered setting.

Memory Definition : Set users Card ID Memory.

System Initialization : Initialize Star Icon-100 system. Initialization Option consists of Event
Clear, Card Clear, Time Schedule Clear, System Clear.

Reader Status : Certify basic information of the system (Star Icon-100). Can certify how to
register Data of day, time, Antipassback, Reader mode, communication speed, Eight Digit Input
Mode, time schedule, Holiday, etc.

Dial-Up Connection : To set a Setup step easily (after installing program first), beginners can use

Software Manual

Star Icon-100 Manual V2.6 (English) -17-

IDTECK

The Company Leads High Security


the Setup Wizard.
-

Setup Wizard : To set a Setup step easily (after installing program first), beginners can use the
Setup Wizard.

Database

Company Definition : Register, manage company.

Title(Position) Definition : Register, manage Title(position) by company.

Department Definition : Register, manage department by company.

Card Type Definition : Register, manage Card Type. Select Card Type in user registration by type
of user, visitor, etc.

System Definition : Register, manage information of Star Icon-100 system.

Access Group Definition : Register, manage access region and time by group. Set Access group
of Star Icon-100 reader.

Card Holder : Manager registration and deletion of registered user data and card, fingerprint data.

Login ID & Password Definition : Registers a new user or delete user, and changes password.
Also, allow functions by user optionally.

Database Backup/Restore : Search Event, Alarm database files by date, then backup or restore.

Option : Select serial chain or dial-up chain . And select whether to use sound by alarm event or
not. If so, select sound file.

Status

Software Manual

Star Icon-100 Manual V2.6 (English) -18-

IDTECK

The Company Leads High Security

Door Control & Status : Control the door. Can unlock or lock the doors Lock and confirm
Locks status by real time. If Contact is installed, can confirm opening and closing of door by real
time.

Event Status : See Event status in screen.

Alarm Status : See Alarm status in screen.

Communication Status : Execute a window of communication status.

Report

Card Holder Report : Search or print data and list of registered users.

Event Report : Register or print event status by period, by time, by door, by individual attendance
status.

Alarm Report : Register or print Alarm status by period, by time, by door.

.
z

View

Vertical : Windows in the main screen align vertically.

Horizontal: Windows in the main screen align horizontally.

About

Program Information : Show this program information.

4. Operation
Software Manual

Star Icon-100 Manual V2.6 (English) -19-

IDTECK

The Company Leads High Security

4.1 Controller
z

Set Communication
Set communication environments.

Comm Port set communication port connected between Star Icon-100 system and computer.
Defaulted value is COM1
Baud Rate set communication speed between Star Icon-100 system and computer. Defaulted
value is 9600bps.
Parity Bit, Data Bit, Stop Bit use defaulted value.
When communication setup is completed, Click OK button to save, then Close button to
exit.

Set System Time


Apply to the transmitted date and time of Star Icon-100.

Software Manual

Star Icon-100 Manual V2.6 (English) -20-

IDTECK

The Company Leads High Security

Date, Week, Day, Time is entered computers date, time automatically. If entered value is
incorrect, you can also make direct input by typing in each field.
Select a Star Icon-100 systems address to want to change data and time in Select(Check)
Reader(Door) Address. (Multi-selection is possible.)
To transmit data, click Transmit button.
If Success message is showed, this procedure is finished. Click Close button to exit.

Reference: Transmit Button


A dialogue box will appear when above procedure is successfully
completed when transmit to Star Icon-100 system after clicking
Transmit button.

If not so, adopt proper method as message or refer to a manager.

Holiday Definition
Register and transmit a holiday. (Refer to the Timeshedule registration)

Software Manual

Star Icon-100 Manual V2.6 (English) -21-

IDTECK

The Company Leads High Security

Holiday Code is used from 01 to 10 and one code can register 32 holidays the maximum.
Input a Holiday Name and Holiday Date.
Click Save button to save.
Select a Star Icon-100 systems address to register in Select(Check) the Reader(Door)
Address.(Multi-selection is possible.)
Click Transmit button to transmit.
If Success message is showed, this procedure is finished. Click Close button to exit.
When want to change a holiday, you select code to change in Holiday Code. Then change the
holiday. Click Save button to save. (Click Transmit button to transmit again after
modifying.)
Click Delete button after selecting Holiday Code to want to delete.
z

Timeschedule Definition
Register and transmit group by day.
Timeschedule can be set 5 time ranges on each day. When attendance is allowed always, Timeschedule
is set 00:00-24:00 from Sunday to Saturday including holiday.
Also, if you allow attendance as time range on specific day, input Timeschedule

by Schedule One,

Schedule Two, Schedule Three, Schedule Four, Schedule Five in time field.
For example, if you allow from 09:00 to 18:00 except from 12:01 to 13:00 on Sunday, input as
following step.

Software Manual

Star Icon-100 Manual V2.6 (English) -22-

IDTECK

The Company Leads High Security

Input 09:00 and 12:00 in Schedule One field, 13:01 and 18:00 in Schedule Two field on Sunday.

TimeSchedule Code can be used from 01 to 10 and input attendance time by related code.
Input a TimeSchedule Name.
Input a time by day.
Select a Holiday Code to apply to a TimeSchedule Code which is inputting presently. If
Holiday is not applied, select None or select a suitable Holiday Code.
If select Holiday Code, appear Holiday Name and TimeSchedule which is applied holiday on
the right side as following figure

Click Save button to save.

Software Manual

Star Icon-100 Manual V2.6 (English) -23-

IDTECK

The Company Leads High Security


Select a Star Icon-100 systems address in Select(Check) the Reader (Door)
Address.(Multi-selection is possible.)
Click Transmit button to transmit to a selected system.
If Success message is showed, this procedure is finished. Click Close button to exit.
Change a stored time in TimeSchedule after selecting TimeSchedule Code. Click Save
button to save. (If you modified a stored time in TimeSchedule, click Transmit button to
transmit again.)
Select TimeSchedule Code to want to delete. Then, click Delete button.
z

Input/Output Definition
Set Input/Output signal of Star Icon-100 system, transmit set values to the system. An Input/Output
point decides which Output Signal is activated when the Star Icon-100 system gets an Input Signal (for
example, Exit, Contact, Fire, Sensor, Tamper, etc). Also, Input/Output Signal can control Operating
time of Input Signal with TimeSchedule.

Select a Star Icon-100 system to set an Input/Output point in System Address.


Select an Input points number to use in Input Point.
Select a type of Input point selected above in Input Type.
Select operating time of input point in TimeSchedule.
When Input point Signal is activated from Out 1, Out 2, Out 3, Out 4, Out 5, decides which
Output point Signal is used. Then select operating time of Output point by seconds.

Software Manual

Star Icon-100 Manual V2.6 (English) -24-

IDTECK

The Company Leads High Security

For example, when Input 1 is used Out 1 in Input point, selects operating second of Out 1
(defaulted value is 03 sec). Other Output points (Out 2, Out 3, Out 4, Out 5) select 00 sec.
Output point can be operated several devices simultaneously. Namely, if Out 1, Out 2 is
operated simultaneously when Input 1 is activated, Operating second of Out 1, Out 2 should
be selected other sec (except 00 sec).
Click Save button to save.
Select the address of Star Icon-100 in Select(Check) the Reader(Door) Address. (Multiselection is possible)
Click Transmit button to transmit.
z

Reader Mode Definition


Transmit how to use a reader of Star Icon-100 system. Star Icon-100 system has two or three security
mode. One is RF Mode, the other RF + Password Mode.

If RF Mode is transmitted, a Star Icon-100 is operated Card Only Mode. Then, when reads a registered
card, allows attendance.
If RF + Password is transmitted, a Star Icon-100 is operated Card + Password Mode. Then, when
inputs card reading and Password, allows attendane.
Click Mode button to change
Select a address of Star Icon-100 in Select(Check) the Reader(Door) Address.(Multi-

Software Manual

Star Icon-100 Manual V2.6 (English) -25-

IDTECK

The Company Leads High Security


selection is possible)
Click Apply button to transmit.

Reference: Reader Mode Option


When apply to Timeschedule is operated RF Card + Password mode.
But when doesnt apply to Timeschecule is operated RF Card Only.
Click RF Card + Password button, then will enable Reader Mode
Option frame. Timeschedule is 00, then is operated RF Card +
Password and 01-10, then is operated RF Card + Password when is
application time or operated RF Card Only.

Keypad Mode sets whether to permit users keypad Input when use RFK101 Reader, .

Antipassback Definition
Antipassback is that controls a cards movement through the system by knowing the cards current
location and what areas he can move to/from the location. This transmits whether to use relevant
functions or not.
If Antipassback is used, Star Icon-100 system must add additional reader. And when entry information
is equal to exit information by relevant Star Icon-100. Namely, when a user uses an entry by using card,

Software Manual

Star Icon-100 Manual V2.6 (English) -26-

IDTECK

The Company Leads High Security


must use also an exit set equal system by using card. If user doesnt use card when come in entry, cant
go out.

Click mode button to change.


Select the address of Star Icon-100 registering in Select(Check) the Reader(Door) Address.
(Multi-selection is possible.)
Click Apply button to transmit.

Software Manual

Star Icon-100 Manual V2.6 (English) -27-

IDTECK

The Company Leads High Security


* Zone Antipassback
-

Limit entrance through reader connected one system. In Icon100, one system establish two readers,
it is a match. When information of entrance and exit are equal, permits entrance.
* Global Antipassback

Limit entrance through reader connected several systems. It isnt itself function in Icon100. It is
established Global Antipassback to be possible as Software. To use Global Antipassback, Software
must be operated for 24 hours.

Duress Mode Definition


In emergency, after user inputs registered 2-digit password in advance, read card. Then, Duress mode is
operated, so inform alarm status according to registered setting.

Memory Definition
User can set memory space being saved Card ID directly. Increase or decrease of Card ID storage
number is possible by 500 units. According to Card ID memory setting, event memory storage space is
set automatically.

Software Manual

Star Icon-100 Manual V2.6 (English) -28-

IDTECK

The Company Leads High Security

Reader Status
Reader Status receives basic information of set system(Star Icon-100). Date, Identity reader
information, AntiPassBack, Reader Mode, Baud Rate, Eight Digit Input Mode, TimeSchedule, Holiday.

Software Manual

Star Icon-100 Manual V2.6 (English) -29-

IDTECK

The Company Leads High Security

Select the address of Star Icon-100 system to receive information.


Show device information of selected system when click Receive button.
Identity the registered holidays information or registered a time range of Timeschedule.

Software Manual

Star Icon-100 Manual V2.6 (English) -30-

IDTECK

The Company Leads High Security

4.2 Database
z

Company Definition
Manager Company lists.

Inputs Company Code in Company Code field.


Inputs Company name in Company field.
Click Save button to save in database.
To modify or delete, click company to modify or delete in Company List.
To modify, modifies Company name, then click Save button to save modified data. To
delete, click Delete button.
z

Title(Position) Definition
Manager title(position) and list.

Selects Company.
Inputs title(position) code in Title Code field.
Inputs title(position) name in Title field.
Click Save button to save.
To modify or delete, selects title(position) to modify or delete in Title List.
To modify, modifies title(position) name, then click Save button to save modified data. To
delete, click Delete button.

Software Manual

Star Icon-100 Manual V2.6 (English) -31-

IDTECK

The Company Leads High Security


z

Department Definition
Manager Department list.

Selects Company.
Inputs Department code in Department Code field.
Inputs Department name in Department field.
Click Save button to save.
To modify or delete, selects Department name in Department List.
To modify, modifies Department name, then click Save button to save modified data. To
delete, click Delete button
z

Card Type Definition


Register Card Types that divide type of users cards, visitors cards, temporary cards.

Inputs a Type Code in Code.


Inputs a Type Name in Card Name.
Click Save button to save.
To modify or delete, select Type Name in Card Type List.
To modify, modifies Type Name, then click Save button to save modified data. To delete,
click Delete button

Software Manual

Star Icon-100 Manual V2.6 (English) -32-

IDTECK

The Company Leads High Security

System Definition
Register information of Star Icon-100 system.

Usually to use one Star Icon-100 system, System Address is 00 or 01. To use several Star
Icon-100 systems simultaneously, System Address is particularly set each system.
System Name is the name of Star Icon-100 system.
System Location selects location (floor in a building) of installed Star Icon-100 system.
Contact Type selects Door Contact type installed Door Lock. By the Contact type, checks the
gate status.
Enter the name of First Reader, Second Reader.
Star Icon-100 is First Reader itself because a reader is included within Star Icon-100 system.
Click Delete button after selecting the reader you want to delete in right Reader (Door) List.
z

Access Group Definition


When use several Star Icon-100 systems simultaneously, entry/exit door of each system make Access
Group System. Then, integrate or limit access regions by group when register users in Card,
FingerPrint holder Screen.

Software Manual

Star Icon-100 Manual V2.6 (English) -33-

IDTECK

The Company Leads High Security

Select Group Code.


Input Group Name.
Select TimeSchedule of Star Icon-100 in Select TimeSchedule.
Double click a reader(entry/exit door) of Star Icon-100 system applied TimeSchedule in
Select Door(DblClick). And register in Selected Door & TimeSchedule.
Register a reader(entry/exit door) of Star Icon-100 that selected Group Code repeatedly step
.
To delete or modify, select a Group Code to want to modify.
To modify, double click to delete a list in Selected Door & TimeSchedule. Click Save
button to save.
Click Delete button to delete. In case, all groups are deleted because Group code is deleted.

Card Holder
Manager users information, registration and deletion.

Software Manual

Star Icon-100 Manual V2.6 (English) -34-

IDTECK

The Company Leads High Security

Input Employee Ref. by using characters and numbers, avoiding duplication. (Employee No.
is not duplicate because it is a primary key.)
Input Last Name.
Input First Name.
Input Card No.
Inputs Password. (Defaulted value: 0000) When input Password, if doesnt input Password,
enters a defaulted value automatically.
Input Tel 1and Tel 2.
Input Registration Date
Select Company (You must select Company to show registered department and title
(position) in each field.)
Select Department.
Select Title(Position).
Input information in Memo.
* Star Icon-100 system
When transmit to user by access group after selecting Star Icon-100 System, select Access
Group. Then, select Access Group transmitting or registering in list. Also when transmitting
specific reader, select each transmitting reader and Timeschedule after selecting Specify
Reader.

Software Manual

Star Icon-100 Manual V2.6 (English) -35-

IDTECK

The Company Leads High Security


Click Save button to save in a database.
Click Transmit button to transmit to a Star Icon-100 system.
Enter Enter key after selecting Employee No. or inputting Card Number then show
registered users information.
To delete users showing screen, click Delete button to delete in a database and Star Icon-100
system.

Reference : Batch Transmit Button


Batch Transmit button transmit registered users information in a database to the system by
access group, or when select specific reader, transmit only to a specific reader.
When execute Batch Transmit, identify transmit status as following figure. (Wait for finishing)

After finishing Batch FP Transmit, show results of transmission by using Notepad.

[Result] is Success when transmit correctly. If not so, adopt proper method as message or
refer to a manager

Software Manual

Star Icon-100 Manual V2.6 (English) -36-

IDTECK

The Company Leads High Security

Reference: Find
Find is used when search registered user in a database.
If you know Employee Ref. or Card Number, input Employee Ref. or Card Number
directly in a user registration screen. Then enter Enter key, show registered data
automatically in a screen. But if not so, use Find Tab.
Click Find>> button after inputting searching conditions. If data is registered, show on
the right side. Select Data to search by mouse, indicate all information in the upper input
field.
If you dont know searching condition, click Whole List button, then indicate registered
users all list at a database on the right side

Software Manual

Star Icon-100 Manual V2.6 (English) -37-

IDTECK

The Company Leads High Security


z

Database Backup/Restore
Backup/Restore search Event, Alarm database files by date, then backup or restore.

1. Backup

Select files to backup between Event and Alarm in a database


Input a period of data to backup in Back Search Condition(Date).
Click Backup button, then display a following figure. After inputting file path and file name to
register, click Open button to backup.

Upon completion of specifying the type and name of fields, a dialogue box will appear when
above procedure is successfully completed. Click the OK button.

Software Manual

Star Icon-100 Manual V2.6 (English) -38-

IDTECK

The Company Leads High Security

Reference: Backup, Restore


Backup is that registers data separately in Event, Alarm database.
So, Backup data delete in Event, Alarm database. To restore from
database file, select Restore.

2. Restore

Select files to restore between Event and Alarm in a database.


Click Restore button, then display a following figure. After inputting file path and file name
to register, click Open button to restore.

Software Manual

Star Icon-100 Manual V2.6 (English) -39-

IDTECK

The Company Leads High Security

Upon completion of specifying the type and name of fields, a dialogue box will appear when
above procedure is successfully completed. Click the OK button.

Loin ID & Password Definition


Register or delete user ID, set authority assign and change Password.
User checked Add, Del, Permission Check when register user ID registers, deletes user ID and set
authority assign only.
After installing this program, user ID is admin without password. Admin user is checked Add, Del,
Permission Check, so can use the program to register, delete user ID and set authority assign.

Software Manual

Star Icon-100 Manual V2.6 (English) -40-

IDTECK

The Company Leads High Security


* Add User ID

Click Add button.


Input New User ID.
Input Password.
Input again in Confirm Password field.
Check Add, Del, Permission Check. (Checked user can use the program to register, delete
user Id and set authority assign. Unchecked user can change only login password.)
Click OK button to save.

* Del User ID

Click Delete button.


Select User ID List to delete on the right side.
Click Delete button, then you will see a prompt message whether to delete. To delete, click
Delete button.

Software Manual

Star Icon-100 Manual V2.6 (English) -41-

IDTECK

The Company Leads High Security


* Change Password

Click Change Password button.


Input current password in Enter current password field, then enter Enter key. If current
password is correct, will appear password field to change automatically.
Input new password to change in Enter new password field.
Input new password to confirm again in a Confirm new password field
Click OK button to save.

* Permission(Detail)
Set user authority functionally. To assign all authorities to specific user ID click All Permission
button, then all functions are selected. Click Save button to save.
Also to delete all authorities click Clear Permission button, then all functions are cleared. Click
Save button to save.
To clear each authority functionally, click All or Clear button below each functions list. Then can
select or clear all function in a relevant list. Also click specific function by using mouse, can set proper
authorities as user ID because of selection or deletion.

Software Manual

Star Icon-100 Manual V2.6 (English) -42-

IDTECK

The Company Leads High Security

Reference: Login after detail authority setting


Login again by relevant user ID after authority setting. If user login again
after exiting program, the assigned function is activated at menu and icon
but others is not activated.
If all authorities arent set, user will see only status of attendance and
alarm.

Option
Manager can indicate to decide whether to use Sound function by alarm status and Alarm status to play
sound files when appear alarm to select sound file.

* Alarm Sound
Select or cancel Sound by Alarm sound whether to use or not. In case of selecting sound, click Open
button. A dialogue box will appear, then select sound file.
If you want to listen to the sound file previously, click >> button.
Upon completion of setting, click OK button to save.

Software Manual

Star Icon-100 Manual V2.6 (English) -43-

IDTECK

The Company Leads High Security

Reference : Sound file


Sound file can use a name for the file with *.wav extension only.

4.3 Status
z

Door Control & Status


Identify status of entry/exit doors Open, Close by real time when to control Lock, UnLock of
entry/exit door or to install status of entry/exit doors Lock, UnLock and Contact

Software Manual

Star Icon-100 Manual V2.6 (English) -44-

IDTECK

The Company Leads High Security

When click mouses right button in entry/exit door to Lock or UnLock, following figure will
appear.

If you select Lock, a relevant entry/exit door is locked, or unlocked. Also if select UnLock 5(sec),

Software Manual

Star Icon-100 Manual V2.6 (English) -45-

IDTECK

The Company Leads High Security


maintain Unlock for 5 sec. Then Lock again automatically.

Point : Icon Status & Button


All Door Lock : Lock all registered entry/exit doors.
All Door UnLock : Unock all registered entry/exit doors.

CloseLock : Entry/exit door is locked and Contact is closed.

CloseUnLock : Entry/exit door is unlocked and Contact is closed.

OpenLock : Entry/exit door is locked and Contact is opened.

OpenUnLock : Entry/exit door is unlocked and Contact is opened.

z Event Status
Appear event of Access granted and Fingerpirnt granted, information of Exit button. You can see
current attendances status through Event Status window by real time.

Alarm Event
Indicate information of Access Denied, Finger Error, Timeschedule error, Access door error,
Antipassback error, Contact, Sensor, Fire, Tamper alarm.

Communication Status

Software Manual

Star Icon-100 Manual V2.6 (English) -46-

IDTECK

The Company Leads High Security


Appear Communication Status of between Star Icon-100 system and program.

4.4 Report

Software Manual

Star Icon-100 Manual V2.6 (English) -47-

IDTECK

The Company Leads High Security


z

Card Holder Report


Search and print user list registered in user registration.

Select or input condition of Company, Department, Title, Employee Ref., Last Name, First
Name, Card No. as user need to search. (If you dont input condition to search at all,
registered users all lists are printed.)
Click Print button, then appear preview screen.
Click Preview button in preview screen, then print the Report.

Software Manual

Star Icon-100 Manual V2.6 (English) -48-

IDTECK

The Company Leads High Security


z

Event Report
Search and print information relevant access event status.

Must input Date, Time because of required condition.


Input or select only condition of Company, Department, Last Name, Card No., etc that user
need to search. (If you dont input condition to search, registered users all lists relevant Date
and Time are printed.)
Click Print button, then appear preview screen.
Click Print button in preview screen, then print the Report.

Reference : Export Button


Export Button change searched data to specific file, then save. Using Export
Button, you can save searched data by format of Text File or Microsoft Excel
File.

Software Manual

Star Icon-100 Manual V2.6 (English) -49-

IDTECK

The Company Leads High Security

Alarm Report
Search and print data of Access Denied, Finger Error, Timeschedule error, Access door error,
Antipassback error, Contact, Sensor, Fire, etc in alarm Event Status.

Software Manual

Star Icon-100 Manual V2.6 (English) -50-

IDTECK

The Company Leads High Security

Must input Date, Time because of required condition.


Input condition of Floor, Door, Type that user need to search. (If you dont input condition to
search, registered users all lists relevant Date and Time are printed.)
Click Print button, then appear preview screen.
Click Print button in preview screen, then print the Report.

Reference : Export Button


Export Button change searched data to specific file, then save. Using Export
Button, you can save searched data by format of Text File or Microsoft Excel
File.

Software Manual

Star Icon-100 Manual V2.6 (English) -51-

IDTECK

The Company Leads High Security

4.5 View
z

Vertical
Windows in the main screen align vertically.

Software Manual

Star Icon-100 Manual V2.6 (English) -52-

IDTECK

The Company Leads High Security


z

Horizontal
Windows in the main screen align horizontally.

4.6 About
z

Program Information
Show this program information.

Software Manual

Star Icon-100 Manual V2.6 (English) -53-

You might also like