TOSHIBA ‘Teas101/g9102
SERIAL EPROM
Tc89101P, TC89102P
‘The TCASTO1P is 9 1024-bit sera! EPROM. The TCB9102? isa 2048-bit serial EZPROM. These are fabricate
with floating gate CMOStechnology
FEATURES PIN ASSIGNMENT (TOP VIEW)
‘@singlesv supply
Stow rower Deifation
Serta wad shew
Ssertined mogam ce @uitsin ine =
Stessyrouy surg a=: 7p sovsa
Site fate rae are ona sore ood: eons
Sete rte ele torow powers
Shogumandeh ts come sow
Siecle Cgmnsaton edtor 160
BLOCK DIAGRAM
coven SY raee LT contotsieit : a Power supply
coningn GRP] ee | | i
t
r Eaeeed | rar y | sensi
Dataingut seit Elz GND Ground
FLT enya
‘ 3
pre manevator
evar 3t howeTOSHIBA Teagrovmara7
PIN FUNCTION
exnawe | wput/ounet_| FINCTONS
s epee
(coxcinpat
S ‘The dataisatned a then eda of TR
A The ats output Hom DD at healing edge of TK
Ckisenabed when nat le
> vooa alenainoa
ons opt The West oranaaton islet whan ORG "Hee!
ror? coupe Lee soupa uring program erin erate operatin,
vee av
oxo vena
OPERATIONAL DESCRIPTION
4. INSTRUCTION SET
(0) Te09101
vans ares met —T Dae
on | ae | eee TS Tae | BETES
ee moras. | Atwas.on [1000 0000]
Poon | sowas,o | sowasw [vite weve | wow | won
ew abe = reer oesTOSHIBA Teasto1/est02
(@) Tessr02
leeweion |—aaee | ani aS. Bineme | ese
rewren | AOwa7 mowas.o [otto e000 | oiwor | powns
Cwenble[ vereneee root e008
ew osable or yet e008
2. _ OPERATION METHOD
‘Set and CK to "H* level before executing inswucion. TS changes to “L” level, then CIR is enabled
and operates es the sync signa for serial VO. The Ol data islatched a the rising edge of CLK. The data is
output rom DO at ane taling edge of CTR
Execute instruction only when ROV/BUSY status signal is “H"level, However Busy Monitor instruction can
be executed whenever
Usesonly commancs which are included in the Instruction Set listed above.
(1) Read
‘executing Head insrucion reads our she memory date atthe speed adres ar wutpulitserally
from 00.
(2 Program
[Executing Program instruction automatically stars internal rewriting of the memory date at the
specified address with the input data,
ite: Program instruction isinput & can beset oH" level ever while the intarnal ewiting process
is operating
(@) Chiperase
txecuting Chip Erase instruction automatically Starts intemal erasing of the memary data at all
adress.
[ter Chip Ete instruction is input, GS can be set to “H" level even while the intemal erating
process is operating,
(6). Busy Monitor
‘Executing Busy Monitor instruction outputs the ROVIBURY status signal from D0.
"L" level is output during Program or Chip Erate operation. "level is eutput when Program or
Chip Erase operation is completed
The ROVIBTEY status signalis output unt 5 isswitched to “level
(9) Ewerable
Executing EM Enable instruction sets EW enable mode and enables Program and Chip Erase
Instructions.
(0 EwVDisable
Executing PW Disable instruction sets the En disable mode and disables both the Program and Chip
Erase instructions, Once &MW disable mode is set, EW disable mode is held until EM Enable
inetructon is executed
3. CAUTIONS WHEN TURNING THE POWER ON AND OFF
(3). After turning the pawer on, wait ims for warm-up before executing instruction.
(2). After turning the power on, st either the EM enable made or BW disable mode.
{3}. If the power supply voltage is lower the approximately 35 V, ENV Disable instruction 1
automatically executed internally.TOSHIBA Teeat01/89102
4, TIMING DIAGRAMS
(1) Read
aTOSHIBA
Teastorms107
2) Program
;
iy =F oe tr
beyTOSHIBA ‘Teasi01g9102TOSHIBA ‘Teas101/a9102
(9) EwEnable
= my inninininnininininin
4
Ee (
{
(6) EW Disable
i a
commandTOSHIBA Tee9101/89102
ELECTRICAL CHARACTERISTICS
”
an men] ae wate
Coe one ves radwvee08 ¥
eo ae zo *
Sone Tenpesire 3 oT =
Creag Tempe re tae x
‘RECOMMENDED OPERATING CONOMIONS | (GND #0, Topr=0t070%C)
panasaeTeR [SYMBOL PINs ‘conormions | _ Mtn ex [unis
carn warage ve footie oe
Teswtowvorage | Vi veeasy @ ra
od ven L ‘ve |v
veo [eR [Fs
“ax Coe te
D.C. CHARACTERISTICS ] (GND=OV, Topr#0to70°%)
Tepstcarent " PPS [ae
Dasutiatane torent | _ bo ano FA
ae 2a ~ |v
Uapatiow varage vou ~f- Lely
Spy arene Teo | dumnaprogemorenate Ee aes
‘es _| Gi seueetrronromercnstrreooerton | — | — 1100 LanTOSHIBA Teato1e9102
Ak CHARACTERISTIC. ] (GND=0V, Vec=451055V, Top
PARANA oy Min vee] ns
— ton @ | we
Rinne ee = : ™
Tinga et ee 0 e 7
Tipasewn Tine 350 S a
= 0 a
Ding Setup ine ts Ea = a
Cine Tine * = » me
rowan Tine ® = Ey =
rseitecicle Now oo - oeTOSHIBA ‘Tegs101/g9102
‘A.C. CHARACTERISTICS TIMING DIAGRAMS
topos sooo
20
s
8
om.
royTOSHIBA TC89101/89102
INPUT /OUTPUT CIRCUITRY
manne | 1] ancuray Tana
| |
s :
| swe Hie |
of |
|
|
|
| ‘
ox | mow Hig | ptr tnt
|
Tate
vee
Z
0 JOutput oo +; Oo Initial “Hi-2"
De
op
¢ vee
ov 8057 | output ita “gh?