Professional Documents
Culture Documents
200605
Processes
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
Description
Wire Feeder
22A, 24A
www.MillerWelds.com
Downloaded from www.Manualslib.com manuals search engine
Mil_Thank 4/05
TABLE OF CONTENTS
SECTION 1 SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. California Proposition 65 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 CONSIGNES DE SCURIT LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symboles utiliss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Dangers relatifs au soudage larc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Dangers supplmentaires en relation avec linstallation, le fonctionnement et la maintenance . . . . . .
2-4. Proposition californienne 65 Avertissements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Principales normes de scurit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Information EMF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Site Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3. Gun Recommendation Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4. Equipment Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5. 14-Pin Plug, Shielding Gas And Optional Volt Sense Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-6. 14-Pin Plug Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7. Connecting Welding Gun And Weld Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8. Optional Meter Circuit Board Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9. Motor Start/Burnback Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-10. Installing Wire Guide And Drive Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-11. Installing And Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Optional Side Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 MAINTENANCE & TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS AND ACCESSORIES
WARRANTY
1
1
1
3
3
4
4
5
5
5
7
7
8
8
9
9
9
10
10
10
11
11
12
13
14
15
16
16
17
17
17
18
18
19
20
Y Warning: Protect yourself and others from injury read and follow these precautions.
D
D
D
D
D
D
D
D
D
D
D
D
READ INSTRUCTIONS.
D Read Owners Manual before using or servicing unit.
D Use only genuine Miller/Hobart replacement
parts.
D
D
D
D
D
D
D
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard
AWS F4.1 from Global Engineering Documents (phone:
1-877-413-5184, website: www.global.ihs.com).
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA
022699101 (phone: 6177703000, website: www.nfpa.org).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, from National Fire Protection Association,
P.O. Box 9101, 1 Battery March Park, Quincy, MA 022699101 (phone:
6177703000,website: www.nfpa.org).
OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,
and Part 1926, Subpart J, from U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250 (there
are 10 Regional Officesphone for Region 5, Chicago, is
3123532220,website: www.osha.gov).
Y Avertissement : se protger et protger les autres contre le risque de blessure lire et respecter ces consignes.
2-1.
Symboles utiliss
Symbole graphique davertissement ! Attention ! Cette procdure comporte des risques possibles ! Les dangers ventuels sont reprsents par les symboles graphiques joints.
D
D
D
D
trous.
Sisoler de la pice couper et du sol en utilisant des housses ou des
tapis assez grands afin dviter tout contact physique avec la pice
couper ou le sol.
Ne pas se servir de source lectrique courant lectrique dans les zones humides, dans les endroits confins ou l o on risque de tomber.
Se servir dune source lectrique courant lectrique UNIQUEMENT si
le procd de soudage le demande.
Si lutilisation dune source lectrique courant lectrique savre ncessaire, se servir de la fonction de tlcommande si lappareil en est
quip.
Dautres consignes de scurit sont ncessaires dans les conditions
suivantes : risques lectriques dans un environnement humide ou si lon
porte des vtements mouills ; sur des structures mtalliques telles que
sols, grilles ou chafaudages ; en position coince comme assise, genoux ou couche ; ou sil y a un risque lev de contact invitable ou
accidentel avec la pice souder ou le sol. Dans ces conditions, utiliser
les quipements suivants, dans lordre indiqu : 1) un poste souder DC
tension constante ( fil), 2) un poste souder DC manuel (lectrode)
ou 3) un poste souder AC tension vide rduite. Dans la plupart des
situations, lutilisation dun poste souder DC fil tension constante
est recommande. En outre, ne pas travailler seul !
Couper lalimentation ou arrter le moteur avant de procder
linstallation, la rparation ou lentretien de lappareil. Dverrouiller
lalimentation selon la norme OSHA 29 CFR 1910.147 (voir normes de
scurit).
Installer le poste correctement et le mettre la terre convenablement
selon les consignes du manuel de loprateur et les normes nationales,
provinciales et locales.
Toujours vrifier la terre du cordon dalimentation. Vrifier et sassurer
que le fil de terre du cordon dalimentation est bien raccord la borne
de terre du sectionneur ou que la fiche du cordon est raccorde une
prise correctement mise la terre.
En effectuant les raccordements dentre, fixer dabord le conducteur
de mise la terre appropri et contre-vrifier les connexions.
D
D
D
dcharger les condensateurs dalimentation selon les instructions indiques dans la partie Entretien avant de toucher les pices.
LES RAYONS DARC peuvent entraner des brlures aux yeux et la peau.
Le rayonnement de larc du procd de soudage
gnre des rayons visibles et invisibles intenses
(ultraviolets et infrarouges) susceptibles de provoquer des brlures dans les yeux et sur la peau.
Des tincelles sont projetes pendant le soudage.
D Porter un casque de soudage approuv muni de verres filtrants appropri pour protger visage et yeux pendant le soudage (voir ANSI
Z49.1 et Z87.1 numr dans les normes de scurit).
D Porter des lunettes de scurit avec crans latraux mme sous votre casque.
D Avoir recours des crans protecteurs ou des rideaux pour
protger les autres contre les rayonnements les blouissements et
les tincelles ; prvenir toute personne sur les lieux de ne pas
regarder larc.
D Porter des vtements confectionns avec des matires rsistantes
et ignifuges (cuir, coton lourd ou laine) et des bottes de protection.
DES
PARTICULES
VOLANTES
peuvent blesser les yeux.
D Le soudage, lcaillement, le passage de la
pice la brosse en fil de fer, et le meulage
gnrent des tincelles et des particules
mtalliques volantes. Pendant la priode de
refroidissement des soudures, elles risquent
de projeter du laitier.
D Porter des lunettes de scurit avec crans latraux ou un cran
facial.
2-3.
LE
RAYONNEMENT
HAUTE
FRQUENCE (HF) risque de provoquer
des interfrences.
SUR-
D
D
D
D
D
D
D
2-4.
2-5.
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping, American Welding Society Standard AWS
F4.1 de Global Engineering Documents (tlphone : 1-877-413-5184, site
Internet : www.global.ihs.com).
Standard for Fire Prevention During Welding, Cutting, and Other Hot
Work, NFPA Standard 51B, de National Fire Protection Association, P.O.
Box 9101, 1 Battery March Park, Quincy, MA 02269-9101 (tlphone :
617-770-3000, site Internet : www.nfpa.org).
2-6.
Information EMF
SECTION 3 INSTALLATION
3-1. Specifications
Type of Input
Power
Welding Power
Source Type
24 Volts AC Single
Phase
7 Amperes 50/60
Hz
Constant Voltage
(CV) DC With
14-Pin And
Contactor Control
Wire Feed
Speed Range
75 to 750 ipm
(1.9 To 19 mpm)
Wire
Diameter
Range
Welding
Circuit Rating
.023 To 5/64 in
(0.6 To 2 mm)
Max Spool Weight:
60 lb (27 kg)
Overall
Dimensions
Weight
Length: 23-1/2 in
(597 mm)
100 Volts,
500 Amperes,
100%
Duty Cycle
Width: 10-3/4 in
(273 mm)
35 lb (15.9 kg)
Height: 11 in
(279 mm)
5
1
Wire Feeder
Lifting Eye
Rubber Feet
Slot
Wire Spool/Reel
Gun
M25 Or M40
GA-40GL
3
4
5
6
4
6
2
115VAC
Contactor
6
3-5. 14-Pin Plug, Shielding Gas And Optional Volt Sense Lead
1
4
Connect to work.
Power Switch
1
Tools Needed:
5/8, 11/16 in
802 349-A
J
I
N
H
G
B
L
M
F
C
E
Pin Information
0 to +10 volts dc input command signal from remote control with respect to pin D.
Ref. S-0004-A
Gun Block
6
7
Tools Needed:
9/16, 5/8 in
Ref. 802 356
DIP Switch S2
2
1
Inches/Minute
Or
Or
Tools Needed:
1/4 in
Ref. 802 357 / Ref. 186 266
Remove wrapper.
1
2
Tools Needed:
Non-Conductive
1/4 in
Tools Needed:
3/8 in
801 923-C
Retaining Ring
Hub Tension Adjustment Nut
Pressure Assembly
Adjustment Knob
Tighten
WOOD
Tools Needed:
15/16 in
SECTION 4 OPERATION
4-1. Front Panel Controls
1
Jog/Purge Switch
192 503-C
Preflow Control
4
1
Postflow Control
Run-In Control
3 Months
Repair Or
Replace
Cracked
Weld Cable
Replace
Unreadable
Labels
14-Pin Cord
Gun Cable
Clean And
Tighten
Weld
Terminals
Replace
Cracked
Parts
Gas Hose
6 Months
Clean
Drive
Rolls
OR
802 349-A
5-3. Troubleshooting
Trouble
Remedy
Wire does not feed, unit completely inop- Turn Power switch On.
erative.
Check 14pin plug PLG2 connections.
Check input power.
Wire does not feed.
Readjust hub tension and drive roll pressure (see Section 3-11).
Use correct size drive roll (see Parts List).
Clean or replace dirty or worn drive roll (see Section 3-10).
Remove weld spatter around nozzle opening.
Replace contact tip or liner. See gun Owners Manual.
Have Factory Authorized Service Agent check drive motor and control board PC1.
Wire feeds when Jog switch is pressed Check gun trigger connection at wire feeder. Check gun trigger leads and trigger switch. See gun Owners
but not when gun trigger is pressed.
Manual.
Wire feeds as soon as power is applied. Check gun trigger. See gun Owners Manual.
Wire does not feed until trigger is Check for short between gun trigger leads and weld cable. Repair or replace gun trigger leads.
pressed but continues to feed after trigger is released.
Gas valve rattles loudly and wire feeds Check for short between gun trigger leads and weld cable. Repair or replace gun trigger leads.
slowly or erratically.
Gas does not flow; wire feeds.
210 430-A
Figure 6-1. Circuit Diagram For Wire Feeder With Optional Equipment
OM-193 472 Page 19
Downloaded from www.Manualslib.com manuals search engine
5
6
7
4
8
10
11
10
9
12
13
14
42
41
15
18
Figure 7-2
&
Figure 7-3
45
40
16
17
44
43
19
20
39
21
22
38
46
37
25
23
24
26
33
35
36
34
31
32
30
27
28
29
802 358-F
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 7-2. Drive Assembly, Wire (2 Drive Roll) (Fig 7-1 Item 40)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
602 009 . . .
172 075 . . .
054 263 . . .
010 224 . . .
166 072 . . .
089 562 . . .
085 244 . . .
089 477 . . .
085 243 . . .
166 071 . . .
151 828 . . .
079 634 . . .
144 172 . . .
172 391 . . .
048 449 . . .
124 778 . . .
605 308 . . .
079 625 . . .
121 271 . . .
172 076 . . .
092 865 . . .
192 874 . . .
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
9
8
10
11
12
2
1
13
14
21
20
22
15
19
17
16
18
802 019-A
Item
No.
Diagram
marking
Part
No.
Description
Quantity
Figure 7-3. Drive Assembly, Wire (4 Drive Roll) (Fig 7-1 Item 40)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
.............
602 009 . . .
172 075 . . .
166 072 . . .
054 263 . . .
010 224 . . .
089 562 . . .
085 244 . . .
089 477 . . .
085 243 . . .
166 071 . . .
079 634 . . .
151 828 . . .
166 338 . . .
605 308 . . .
187 325 . . .
144 172 . . .
166 337 . . .
168 590 . . .
072 010 . . .
124 778 . . .
079 625 . . .
092 865 . . .
172 077 . . .
121 271 . . .
192 875 . . .
10
12
11
4
4
4
2
2
2
2
2
2
1
1
2
1
1
1
1
1
2
2
1
2
1
1
1
1
13
9
14
8
7
6
25
5
3
15
4
16
2
1
21
24
22
23
20
19
18
17
802 018-A
Table 7-1. Drive Roll And Wire Guide Kits (2 Drive Roll)
NOTE
Wire Diameter
Fraction
Decimal
Metric
Kit No.
Drive Roll
Part No.
Type
Inlet
Wire Guide
.023/.025 in
.023/.025 in
0.6 mm
087 131
087 130
V-Grooved
056 192
.030 in
.030 in
0.8 mm
079 594
053 695
V-Grooved
056 192
.035 in
.035 in
0.9 mm
079 595
053 700
V-Grooved
056 192
.040 in
.040 in
1.0 mm
161 189
053 696
V-Grooved
056 192
.045 in
.045 in
1.2 mm
079 596
053 697
V-Grooved
056 193
.052 in
.052 in
1.3 mm
079 597
053 698
V-Grooved
056 193
1/16 in
.062 in
1.6 mm
079 598
053 699
V-Grooved
056 195
.035 in
.035 in
0.9 mm
044 749
072 000
U-Grooved
056 192
.045 in
.045 in
1.2 mm
079 599
053 701
U-Grooved
056 193
.052 in
.052 in
1.3 mm
079 600
053 702
U-Grooved
056 193
1/16 in
5/64 in
.062 in
.079 in
1.6 mm
2.0 mm
079 601
079 602
053 706
053 704
U-Grooved
U-Grooved
056 195
056 195
.035 in
.035 in
0.9 mm
079 606
132 958
V-Knurled
056 192
.045 in
.045 in
1.2 mm
079 607
132 957
V-Knurled
056 193
.052 in
.052 in
1.3 mm
079 608
132 956
V-Knurled
056 193
1/16 in
.062 in
1.6 mm
079 609
132 955
V-Knurled
056 195
.068-.072 in
.068-.072 in
1.8 mm
089 984
132 959
V-Knurled
056 195
5/64 in
.079 in
2.0 mm
079 610
132 960
V-Knurled
056 195
.045 in
.045 in
1.2 mm
083 318
083 489
U-Cogged
056 193
.052 in
.052 in
1.3 mm
083 317
083 490
U-Cogged
056 193
1/16 in
.062 in
1.6 mm
079 614
053 708
U-Cogged
056 195
5/64 in
.079 in
2.0 mm
079 615
053 710
U-Cogged
056 195
S-0157-C
Table 7-2. Drive Roll & Wire Guide Kits (4 Drive Roll)
NOTE
Wire Diameter
Fraction
Decimal
.023/.025 in
.023/.025 in
Metric
Kit No.
Drive Roll
Part No.
Type
Wire Guide
Inlet
Intermediate
0.6 mm
087 132
087 130
V-Grooved
056 192
056 206
.030 in
.030 in
0.8 mm
046 780
053 695
V-Grooved
056 192
056 206
.035 in
.035 in
0.9 mm
046 781
053 700
V-Grooved
056 192
056 206
.040 in
.040 in
1.0 mm
191 917
053 696
V-Grooved
056 192
056 206
.045 in
.045 in
1.2 mm
046 782
053 697
V-Grooved
056 193
056 207
.052 in
.052 in
1.3 mm
046 783
053 698
V-Grooved
056 193
056 207
1/16 in
.062 in
1.6 mm
046 784
053 699
V-Grooved
056 195
056 209
.035 in
.035 in
0.9 mm
044 750
072 000
U-Grooved
056 192
056 206
.045 in
.045 in
1.2 mm
046 785
053 701
U-Grooved
056 193
056 207
.052 in
.052 in
1.3 mm
046 786
053 702
U-Grooved
056 193
056 207
1/16 in
5/64 in
.062 in
.079 in
1.6 mm
2.0 mm
046 787
046 788
053 706
053 704
U-Grooved
U-Grooved
056 195
056 195
056 209
056 209
.035 in
.035 in
0.9 mm
046 792
132 958
V-Knurled
056 192
056 206
.045 in
.045 in
1.2 mm
046 793
132 957
V-Knurled
056 193
056 207
.052 in
.052 in
1.3 mm
046 794
132 956
V-Knurled
056 193
056 207
1/16 in
.062 in
1.6 mm
046 795
132 955
V-Knurled
056 195
056 209
1.8 mm
089 985
132 959
V-Knurled
056 195
056 209
.068-.072 in .068-.072 in
5/64 in
.079 in
2.0 mm
046 796
132 960
V-Knurled
056 195
056 209
.045 in
.045 in
1.2 mm
083 319
083 489
U-Cogged
056 193
056 207
.052 in
.052 in
1.3 mm
083 320
083 490
U-Cogged
056 193
056 207
1/16 in
.062 in
1.6 mm
046 800
053 708
U-Cogged
056 195
056 209
5/64 in
.079 in
2.0 mm
046 801
053 710
U-Cogged
056 195
056 209
Ref. S-0025-D
Call
1-800-4-A-MILLER
for your local
Miller distributor.
Your distributor also gives
you ...
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Support
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY Subject to the terms and conditions
* Induction Heating Coils and Blankets, Cables, and
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to
Non-Electronic Controls
its original retail purchaser that new Miller equipment sold after
* APT & SAF Model Plasma Cutting Torches
the effective date of this limited warranty is free of defects in
* Remote Controls
material and workmanship at the time it is shipped by Miller. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
* Accessory (Kits)
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
* Replacement Parts (No labor)
WARRANTIES OF MERCHANTABILITY AND FITNESS.
* Spoolmate Spoolguns
Within the warranty periods listed below, Miller will repair or
* Canvas Covers
replace any warranted parts or components that fail due to such
defects in material or workmanship. Miller must be notified in
writing within thirty (30) days of such defect or failure, at which
time Miller will provide instructions on the warranty claim
procedures to be followed.
2.
*
*
*
*
*
*
*
*
*
3.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
4.
6 Months Batteries
5.
90 Days Parts
2.
3.
miller_warr 200601
Owners Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
Distributor
Address
City
State
Zip
For Service
Contact a DISTRIBUTOR or SERVICE AGENCY near you.
Replacement Parts
Training (Schools, Videos, Books)
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
Welding Process Handbooks
To locate a Distributor or Service Agency visit
www.millerwelds.com or call 1-800-4-A-Miller
PRINTED IN USA
International HeadquartersUSA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
European Headquarters
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
www.MillerWelds.com