You are on page 1of 2

FR1200 Installation Guide

Version: V1.1

Warning: No operating with power on


2.Other Functions

Date: Aug, 2011


(1) Wiring Terminals: As the figure below.

1.Equipment Installation

Address

Switch Setting

Address

F12 Mounting Paper

8
4
2

In st ru ct io n fo r th e Mo un ti ng P ap er

ON

Be fo re t he d ev ic e is f as te ne d, p le as e
st ic k th e pa pe r to t he p la ce w he re y ou
wa nt t o in st al l it , th en m ak e ho le s an d
la y ca bl es a cc or di ng t o th e mo un ti ng
pa pe r.

Terminal
Resistance

Fi xi ng H ol e

(only for your reference)

Switch Setting
ON

ON

ON

ON

2
1

Fi xi ng H ol e

Dip Switch

Wi ri ng Ho le

ON

ON

(1) Post the mounting template on the (2) Remove the screw on the
wall. Drill the holes according to
bottom of device.
the marks on the template (holes
for screws and wiring).

(3) Take away the back plate.

+12V

GND

485+

GND

485-

Wiring Terminals

ON

ON

4
1

Back View

(2) Dip Switch Setting


It is adopted binary coding and little endian. Number 1-4 switches are used to set the 485
address number (device number).
The address number setting by place these 4 switches are shown as the right sheet above.
Number 5 switch is idle.
Number 6 switch is used to se tthe terminal resistance in RS485 communication: Switch
it to ON status, that is add a terminal resistance of 120 ohm between 485+ and 485-.
(3) Manual Reset
If the device does not work properly because of
misoperation or other abnormality, you can use
(4) Fix the plastic pad and the back (5) Tighten the screw on the bottom,
plate on the wall according to the
fix the device to the back plate.
mounting paper.

Reset function to restart it.


Operation: Remove the black rubber cap, then
stick the Reset button hole with a sharp tool
(the tip diameter less than 2mm).

Reset button
Bottom View

3.Connected with Control Panel

Warning: No operating with power on


Note:

(1) Connected as Wiegand Reader

wiegand

a. Please keep the distance between the device and access control or card reader less than 90 meters
(Please use Wiegand signal extender in long distance or interference environment).
b. To keep the stability of Wiegand signal, connect the device and the access control or card reader in
SWITCH

same GND in any case.


EXT
RS485

PC

STATE

PC
RS485

4. Cautions

PWR

ACT

OUT
READER1
READER2

(1)Power cable is connected after all the other wiring. If the device is working abnormally, please
shut down the power first, then make the necessary check . Kindly reminds you that any
hot-plugging may damage the device, and it is not included in the warranty.

Access Control Panel

(2)We recommend the DC 3A/12V power supply. Please contact our technical staff for details.

(2) Connected as inBIO Reader (with External 485)

(3)Please read carefully the terminal description and wiring by rule strictly. Any damage
caused by improper operations will be out of the range of our guarantee.

SWITCH

(4)Keep the exposed part of wire less than 5mm, to avoid unexpected connection.
(5)Please connect the GND before all the other wiring especially under the environment with much

EXT
RS485

PC

STATE

PC
RS485

+12V
GND
485485+
PWR

ACT

electrostatic.

OUT
READER1

(6)Do not change the cable type because of long distance between the power and the device.

READER2

(7) If the 485 communication wire is longer than100 meters, it is needed to set the number 6 dip switch of
Access Control Panel

the last reader to ON state, that is parallel a terminal resistance of 120 ohm between 485+ and 485-.

You might also like