Professional Documents
Culture Documents
Specification
1. Product Overview
Model of SD-ZW9100 series intelligent temperature humidity controller is a special
controller designed for specially process auto-control temperature & humidity. It process
real-time collection and auto control for temperature humidity data by adopting high
performance micro-processor AVR. The humidity sensor is humicap imported from France
HUMIREL. It is with the features of high precision & long-life etc. The temperature sensor
is high accuracy digital sensor produced by MACIM company. This controller has
advantages of high precision ,long-life,easy to install etc.This controller displayed by 2
rows LED digital display.
2. Technical Parameter
1) The range of Temperature measure: -20 ~ 99.9C, measure temperature precision:
0.5C,temperature resolution:0.1
2)
humidity resolution: 1% RH
3)
4)
Power consumption: 2W
5)
Output method: 2 ways active powered output, the standard contact capacity of each way 5A,
7)
Volume: 48mm*48mm*78mm
1) Condition of Starting Heating:measured temperature less than setted lower limits value
2)Condition of Stopping Heating:measured temperature more than setted upper limits value
When measured temperature less than setted lower limits value(for example:23.6 ),the
heating will output 220V voltage.The heater begin to operate,and the heat indicate light.When
temperature up to setted value(for example 25.8 ),heating output will stop.By this operate,the
controller will control temperature in the setted value.
3) Condition of Starting Humidifying:measured humidity less than setted lower limits value
4) Condition of Stopping Humidifying:measured humidity more than setted upper limits value
When measured humidity less than setted lower limits value(for example:70%),the humidifying
will output 220V voltage.The humidifier begin to operate,and the humidifying indicate light.When
humidity up to setted value(for example 85%),humidifying output will stop.By this operate,the
controller will control humidity in the setted value.
[Note] When the controller in automatic control state, humidity or temperature will reach a
critical control point.Then they controller may jitter.So we added on / off delay function for the
controller.This mean that when the temperature or humidity control reached setted value,it will not
immediately start heating or Humidifying.It will delay and wait for the collected data stabilizing,
then taking on / off command.This will reduce the frequently action,get a long-life.
4. Produce Function
1) Display Temperature and Humidity
Up LED display real-time temperature,down LED display real-time humidity
2) Fault Indicate
When the temperature and humidity probe has fault,the digital tube will display
.When
5. Wiring Diagram
Please wiring according to following wiring.Sensor signal wire adopt 4-core cable.The length
can not more than 10meters.If the field interference is prevalent, use 4-core shielded cable, and
single-point ground.
In order to ensure controllers safe and reliable operation , it is recommended to control total
power of heater and humidifier in 2000W. If the total power more than 2000W, please add 220V
AC contactor.
6. Parameter Set
Press SET/DISkey for more than 1s,controller enter setting mode.Press SET once,shift to next
parameter setting.Press ,add a parameter.Press ,deduct a parameter.Windows will display
real-time parameter.
After setting values,pressSET/DISkey for more than 1s,buzzer sounding.Then controller exit
setting state and save setted value to EEPROM.Although power off,parameters will not
disappear.The controller will return to temperature display page.
If you do not operate in 20s at the setting state,system will turn back.The setted parameters will
not be saved.
Table of Humidity Controller Parameters Setting:
7.Attention
1)Sensor should be used avoid sunshine,rain,corrosive gases.Or the life and accuracy will be
deducted.
2)There is internal system hardware watchdog,can long-term reliable operation. If unusual
circumstances appear, re-power it.It will back to normal.Or contact us.
3) Do not make total power more than 2000W.If more than 2000W,connect 220V AC contactor.
8. Sales Service
We provide 1year quality guarantee.If there are problem of product quality(not produced by
personal),it has guarantee of 3 months.In this period,we can change for new one.If it is over 3
months and less than 12 months,we can repair for free.If there are technical problems,we will
provide technical support for life-long.
5