Professional Documents
Culture Documents
www.andhracolleges.com
⋆⋆⋆⋆⋆
1. The velocity distribution of flow over a plate is parabolic with vertex 30 cm from
the plate, where the velocity is 180 cm/s. If the viscosity of the fluid is 0.9 N.s/ m2
find the velocity gradient and shear stresses at distances of 0, 15 cm and 30 cm
from the plate. [16]
3. A 300mm diameter pipe carries water under a head of 20m with a velocity of 3.5m/s.
If the a axis of the pipe turn through 450 , find the magnitude and direction of the
resultant force at the bend . [16]
www.andhracolleges.com
oil of specific gravity 0.87 for the purpose of flow measurement. The differential
head is to be indicated by a U-tube manometer containing mercury (specific
gravity=13.6). If the manometer reading is not to exceed 18cm when the flow
is 17 kg/sec, what should be the diameter of the orifice? Assume Cd =0.62.
[6+10]
7. (a) Show that the momentum correction factor for laminar flow through a circular
pipe is equal to 4/3.
(b) A shaft having a diameter of 50mm rotates centrally in a journal bearing hav-
www.andhracolleges.com
ing a diameter of 50.15 mm and length 100mm. The annular space between
the shaft and the bearing is filled with oil having viscosity of 0.9 poise. Deter-
mine the power absorbed in the bearing when the speed of rotation is 60 rpm
[8+8]
⋆⋆⋆⋆⋆
www.andhracolleges.com
Seminar Topics - Scholarships - Admission/Entrance Exam Notifications
2 ofUSA-UK-Australia-Germany-France-NewZealand
2 Universities List
www.andhracolleges.com
⋆⋆⋆⋆⋆
1. (a) Calculate the specific weight, specific mass, specific volume and specific gravity
of a liquid having a volume of 6 m3 and weight of 44 kN.
(b) Distinguish between simple manometer and a differential manometer. [8+8]
2. (a) If φ=3xy, find x and y components of velocity at (1,3) and (3,3). Determine
the discharge passing between streamlines passing through these points.
(b) Define one-dimensional, two-dimensional and three-dimensional flows? [10+6]
4. (a) Define the scale ratio in distorted models and obtain the expression of scale
ratio for velocity and scale ratio for area of flow.
www.andhracolleges.com
(b) The rate of flow in a 120mm diameter pipe is measured with a venturimeter
with a 40mm diameter throat. When a mercury manometer is connected
across the converging section reads 7mm, the flow rate is 1.5kg/sec. What is
the coefficient of discharge at that flow rate and what is permanent loss of
head? (Specific gravity of mercury =13.6). [7+9]
5. (a) Explain with a neat sketch the boundary layer characteristics when a fluid is
flowing over a flat plate.
(b) A thin flat plate 0.3 m wide and 0.6 m long is suspended and exposed parallel
to air flowing with a velocity of 3 m/sec. Calculate drag force on both sides
of the plate when the 0.3 m edge is oriented parallel to free stream. Consider
flow to be laminar and assume for air kinematic viscosity is 0.18 stokes and
density is 1.2 kg/m3 . [10+6]
6. A pipeline ABC 180 m long is laid on an upward slope of 1 in 60. The length of
portion AB is 90 m and its diameter is 0.15 m. At B the pipe section suddenly
enlarges to 0.30 m diameter and remains so for the remainder of its length BC, 90
m. A flow of 50 litres per second is pumped into the pipe at its lower end A and is
discharged at the upper end C into a closed tank. The pressure at the supply end
A is 137.34 kN/m2 . Sketch [16]
Seminar Topics - Scholarships - Admission/Entrance Exam Notifications
1 ofUSA-UK-Australia-Germany-France-NewZealand
2 Universities List
7. (a) Show that the momentum correction factor for laminar flow through a circular
pipe is equal to 4/3.
(b) A shaft having a diameter of 50mm rotates centrally in a journal bearing hav-
www.andhracolleges.com
ing a diameter of 50.15 mm and length 100mm. The annular space between
the shaft and the bearing is filled with oil having viscosity of 0.9 poise. Deter-
mine the power absorbed in the bearing when the speed of rotation is 60 rpm
[8+8]
⋆⋆⋆⋆⋆
www.andhracolleges.com
Seminar Topics - Scholarships - Admission/Entrance Exam Notifications
2 ofUSA-UK-Australia-Germany-France-NewZealand
2 Universities List
www.andhracolleges.com
⋆⋆⋆⋆⋆
1. Two large fixed parallel planes are 12mm apart. The space between the surfaces
is filled with oil of viscosity 0.972Ns/ m2 . A flat thin plate 0.25 m2 area moves
through the oil at a velocity of 0.3m/s. Calculate the drag force:
(a) When the plate is equidistant from both the planes and
(b) When the thin plate is at a distance of 4mm from one of the plane surfaces.
[16]
www.andhracolleges.com
theory of Similarity?
i. Reynolds number
ii. Froude number and
iii. Mach Number.
(b) A venturimeter its axis vertical, the inlet and throat diameters being 90 mm
and 45 mm respectively. The throat is 150 mm above inlet and Cd =0.96, oil
of specific gravity 0.8 flows up through the meter at a rate of 0.01 m3 /s. Find
the pressure difference between inlet and throat. [6+10]
5. (a) For a fluid flowing over a flat plate, draw
i. Velocity distribution in the laminar and turbulent boundary layers
ii. Shear stress distribution for the boundary layer developing on either side
of the plate.
(b) A plate 4 m x 1.5 m is held in water moving at 1 m/sec parallel to its length.
If the flow in the boundary layer is laminar at the leading edge of the plate,
find [6+10]
i. the distance from leading edge where the boundary layer flow changes
from laminar to turbulent flow
Seminar Topics - Scholarships - Admission/Entrance Exam Notifications
1 ofUSA-UK-Australia-Germany-France-NewZealand
2 Universities List
www.andhracolleges.com
Take friction factor 4f = 0.04. [8+8]
7. (a) What do you meant by viscous flow? Mention various forces to be considered
in Navier Stroke’s equation.
(b) Through a horizontal circular pipe of diameter 100 mm and of length 10m,
an oil of dynamic 0.097 poise and relative density 0.9 is flowing. Calculate
the difference of pressure at the two ends of the pipe, if 100 Kg. of the oil is
collected in a tank in 30 seconds. [10+6]
8. (a) Derive Bernoulli’s equation for compressible flow undergoing adiabatic process?
(b) Find the Mach number when an aero plane is flying at 1100Km/hr through
still air having a pressure of 7 N/ cm2 and temperature -50 C. Wind velocity
may be taken as zero. Take R=287.14J/KgK. Calculate the pressure, temp
and density of air at stagnation point on the nose of the plane. Take K=1.4.
[8+8]
⋆⋆⋆⋆⋆
www.andhracolleges.com
Seminar Topics - Scholarships - Admission/Entrance Exam Notifications
2 ofUSA-UK-Australia-Germany-France-NewZealand
2 Universities List
www.andhracolleges.com
⋆⋆⋆⋆⋆
1. (a) A lubricating oil of viscosity µ undergoes steady shear between a fixed lower
plate and an upper plate moving at speed V. The clearance between the plates
is t. Show that a linear velocity profile results if the fluid does not slip at either
plate.
(b) Describe with a neat sketch a micro-manometer used for very precise mea-
surement of small pressure difference between two points. [8+8]
www.andhracolleges.com
with oil of relative density 0.9 to a depth of 280mm, the remaining volume
containing air at atmosphere pressure. The cylinder rotates about its vertical
axis at such a speed that the oil. Just begins to uncover the base. Calculate
the speed of rotation for this condition. [6+10]
4. (a) Explain about horizontal, vertical and Inclined venturimeter by applying Bernoulli’s
equation at two sections.
(b) Water flows over a Rectangular sharp- crested weir 1m long, the head over the
sill of of the weir being 0.66m. The approach channel is 1.4 m wide and depth
of flow in the channel is 1.2m. Starting from the first principle, determine the
rate of discharge over the weir. Consider also the velocity of approach and the
effect of end contractions. Take Coefficient of discharge for the weir as 0.6.
[8+8]
5. (a) Explain with the help of a sketch the variation of drag coefficient for a circular
cylinder over wide range of Reynolds number.
(b) A cylinder of 0.5 m diameter rotates at 540 r.p.m in air stream of velocity 12
m/sec. If it develop a lift of 96 N per unit length of the cylinder, determine
the ratio of actual to theoretical lift. Take density of air as 1.236 kg/m3 .[8+8]
Seminar Topics - Scholarships - Admission/Entrance Exam Notifications
1 ofUSA-UK-Australia-Germany-France-NewZealand
2 Universities List
www.andhracolleges.com
sections of the pipe and consider minor losses. [6+10]
7. (a) What do you meant by viscous flow? Mention various forces to be considered
in Navier Stroke’s equation.
(b) Through a horizontal circular pipe of diameter 100 mm and of length 10m,
an oil of dynamic 0.097 poise and relative density 0.9 is flowing. Calculate
the difference of pressure at the two ends of the pipe, if 100 Kg. of the oil is
collected in a tank in 30 seconds. [10+6]
8. (a) What do you mean by Sub-sonic, sonic and super sonic flows?
(b) An Aeroplane is flying at an height of 20km, where the temperature is -400 C
.Find the speed of the plane corresponding to Machnumber M=1.8, K=1.4
and R=287J/Kg-K. [8+8]
⋆⋆⋆⋆⋆
www.andhracolleges.com
Seminar Topics - Scholarships - Admission/Entrance Exam Notifications
2 ofUSA-UK-Australia-Germany-France-NewZealand
2 Universities List