Professional Documents
Culture Documents
http://www.lincolnelectric.com/en-us/support/welding-how-to/Pages/pre...
Live Chat
Login/Register
EQUIPMENT
CONSUMABLES
ONLINE STORE
AUTOMATION
INDUSTRIES
EDUCATION
SUPPORT
Arc blow can cause a number of welding problems, including excessive spatter, incomplete fusion, porosity and lower
prevented? In this article, we will examine arc blow and discuss ways to troubleshoot and eliminate this phenomenon
Welding How-To's
Arc blow occurs in DC arc welding when the arc stream does not follow the shortest path between the electrode and t
backward from the direction of travel or, less frequently, to one side.
Welding Projects
First, let's examine some of the terms associated with arc blow. Back blow occurs when welding toward the workpiece
corner. Forward blow is encountered when welding away from the workpiece connection, or at the starting end of the
troublesome with SMAW iron-powder electrodes, or other electrodes that produce large slag coverings, where the effe
forward and under the arc.
Welding Solutions
Magnetic arc blow is caused by an unbalanced condition in the magnetic field surrounding the arc. This unbalanced c
times, the arc will be farther from one end of the joint than another and will be at varying distances from the workpiece
because of the change in direction of the current as it flows from the electrode, through the arc, and into and through
The concentric flux fields will remain circular when they can stay in one medium expansive enough to contain them un
if the medium changes (such as from steel plate to air), the circular lines of force are distorted and tend to concentrate
resistance. At a boundary between the edges of a steel plate and air, there is a squeezing of the magnetic flux lines, c
force. This squeezing can result in a heavy concentration of flux behind or ahead of a welding arc. The arc then tends
the squeezing and restore the magnetic field balance. It veers away from the side of magnetic flux concentration. This
1 de 6
http://www.lincolnelectric.com/en-us/support/welding-how-to/Pages/pre...
Figure 3-38 illustrates the squeezing and distortion of flux fields at the start and finish of a seam weld. At the start, the magnetic flux lines are concentrated
behind the electrode. The arc tries to compensate for this imbalance by moving forward which creates forward arc blow. As the electrode approaches the en
the seam, the squeezing is ahead of the arc, with a resultant movement of the arc backwards, and the development of back blow. At the middle of a seam in
members of the same width, the magnetic field would be symmetrical, and there would not be any back or forward arc blow. But, if one member should be w
and the other narrow, side blow could occur at the midpoint of the weld.
In Figure 3-40(a), the workpiece cable is connected to the starting end of the seam, and the flux resulting from the returning welding current in the work is
behind the arc. The resulting arc movement would be forward. Near the end of the seam, however, the forward arc movement would diminish the total arc b
by canceling some of the back blow resulting from concentration of the flux from the arc at the end of the workpiece, see Figure 3-41(a). In Figure 3-40(b)
work cable is connected to the finish end of the seam, which results in back blow. Here, it would increase the back blow of the arc flux at the finish of the we
2 de 6
http://www.lincolnelectric.com/en-us/support/welding-how-to/Pages/pre...
The combination of "squeezed" magnetic fluxes is illustrated in Figure 3-41(b). A workpiece connection at the finish of the weld, however, may be what the
welder needs to reduce excessive forward blow at the start of the weld.
Because the effect of welding current returning through the workpiece is less forceful than concentrations of arc-derived magnetic flux at the ends of workpi
positioning of the workpiece connection is only moderately effective in controlling arc blow. Other measures must also be used to reduce the difficulties caus
by arc blow when welding.
High Currents
There is less arc blow with low current than with high. Why? Because the intensity of the magnetic field a given distance from the conductor of electric curre
proportional to the square of the welding current. Usually, serious arc blow problems do not occur when stick electrode welding with DC up to approximately
amps (but this is not an exact parameter since joint fitup and geometry could have major influence.)
DC Currents
The use of AC current markedly reduces arc blow. The rapid reversal of the current induces eddy currents in the base metal, and the fields set up by the ed
currents greatly reduce the strength of the magnetic fields that cause arc blow.
We've already examined the most common form of arc blow, magnetic arc blow, but what other forms might a welder encounter? The second type is therma
blow. The physics of the electric arc require a hot spot on both the electrode and plate to maintain a continuous flow of current in the arc stream. As the elec
is advanced along the work, the arc will tend to lag behind. This natural lag of the arc is caused by the reluctance of the arc to move to the colder plate. The
space between the end of the electrode and the hot surface of the molten crater is ionized and, therefore, is a more conductive path than from the electrode
the colder plate. When the welding is done manually, the small amount of "thermal back blow" due to the arc lag is not detrimental, but it may become a pro
with the higher speeds of automatic welding or when the thermal back blow is added to magnetic back blow.
3 de 6
http://www.lincolnelectric.com/en-us/support/welding-how-to/Pages/pre...
When two arcs are close and have opposite polarities, as in Figure 3-44(a), the magnetic fields between the arcs causes them to blow away from each othe
the arcs are the same polarity, as in Figure 3-44(b), the magnetic fields between the arcs oppose each other. This results in a weaker field between the arc
causing the arcs to blow toward each other.
Usually, when two arcs are used, it is suggested that one be DC and the other AC, as shown in Figure 3-44(c). In this case, the flux field of the AC arc
completely reverses for each cycle, and the effect on the DC field is small. As a result, very little arc blow occurs.
Another commonly used arrangement is two AC arcs. Arc blow interference here is avoided to a large extent by phase-shifting the current of one arc 80 to 9
degrees from the other arc. A so-called "Scott" connection accomplishes this automatically. With the phase shift, the current and magnetic fields of one arc
a maximum when the current and magnetic fields of the other arc are at or near minimum. As a result, there is very little arc blow.
4 de 6
http://www.lincolnelectric.com/en-us/support/welding-how-to/Pages/pre...
With processes where a heavy slag is involved, a small amount of back blow may be desirable; to get this, weld toward the workpiece connection
Wrap the work cable around the workpiece so that the current returning to the power supply passes through it in such a direction that the magnetic field se
will tend to neutralize the magnetic field causing the arc blow
The direction of the arc blow can be observed with an open-arc process, but with the submerged arc process it is more difficult to diagnose and must be
determined by the type of weld defect.
Back blow is indicated by the following:
Spatter
Undercut, either continuous or intermittent
Narrow, high bead, usually with undercut
An increase in penetration
Surface porosity at the finish end of welds on sheet metal
Forward blow is indicated by:
A wide bead, irregular in width
Wavy bead
Undercut, usually intermittent
A decrease in penetration
Fixtures for welding the longitudinal seam of cylinders (see Figure 3-47) should be designed for a minimum of 1-inch clearance between the supporting be
and the work. The clamping fingers or bars that hold the work should be nonmagnetic. Do not attach the workpiece cable to the copper backup bar; make
work connection directly to the workpiece if possible
Abricate the fixture from low-carbon steel. This is to prevent the buildup of permanent magnetism in the fixture
Welding toward the closed end of "horn type" fixtures reduces back blow
Design the fixture long enough so that end tabs can be used if necessary
Do not use a copper strip inserted in a steel bar for a backing, as in Figure 3-48. The steel part of the backup bar will increase arc blow
Provide for continuous or close clamping of parts to be seam-welded. Wide, intermittent clamping may cause seams to gap between clamping points, resu
in arc blow over the gaps
Do not build into the fixture large masses of steel on one side of the seam only. Counter-balance with a similar mass on the other side
5 de 6
http://www.lincolnelectric.com/en-us/support/welding-how-to/Pages/pre...
By understanding the mechanics of arc blow and how to correctly diagnose it in the weld, operators should be able to eliminate it from their applications an
able to create welds without the problems normally associated with arc blow.
Welding Equipment
Welding Wire
GO
6 de 6