Professional Documents
Culture Documents
Strength And
Durability...
Structural Fiberglass
Columns are spun from a
mixture of 45% genuine
marble particles combined
with tough polymer resins
and fiberglass. They have
the look and feel of marble.
They are hard, lightweight,
and strong. They will never
split or rot and are abso-
lutely termite-proof.
Easy
Installation...
Simple instructions included with each unit assure quick and easy installation. All Structural
Fiberglass Columns come complete with a Tuscan cap and base in polyurethane. The finish
readily accepts high quality exterior paint. Minimal surface preparation may be required. Once
painted, our columns will not deteriorate under severe long-term weathering and are extremely
resistant to fire and impact.
Advantages...
• Architecturally
Correct Tuscan Style
enhances any
structure in any
setting.
• No splitting or
rotting.
• Will not deteriorate
in heavy weathering.
• Resistant to impact
damage.
• Termite-proof.
• Fire resistant.
• Fast & easy to install.
• Maintenance-free.
• Designed to bear
structural loads.
67
ARCHITECTURAL PRODUCTS BY OUTWATER L.L.C. • Phone: 1-800-835-4400 Fax: 1-800-835-4403
RESIN CAPITALS FOR USE WITH OUR ROUND FIBERGLASS COLUMNS
• HIGH LOAD BEARING CAPACITY • WATERPROOF • EASY TO INSTALL • INSECTPROOF
LOAD BEARING CAPACITY
DIAMETER LOAD IN POUNDS
Our capitals provide both a decorative as well as structural function. The results of independently 6 Inches 8,000
operated compressive strength testing and load bearing capacities of our capitals are listed in the chart: 8 Inches 10,000
10 Inches 12,500
12 Inches 15,000
HOW TO FINISH
It's Simple: No primer coat is necessary. Be sure to use a high quality paint and follow the manufacturer's instructions for best results.
4 3
5 1
Temple of Winds Roman Corinthian Greek Erecthium Roman Ionic Scamozzi
NAME PART # FITS OUR COLUMN DIA. BOTTOM DIA. (A) HEIGHT (B) ABACUS (C) WEIGHT IN LBS. EACH
MC-6-I 6" 4-7/8" 2-1/4" 5-3/4" 4 90.00 PLEASE NOTE: All dimensions
Roman MC-8-I 8" 6-5/8" 3" 7-7/8" 5-1/2 120.00 are considered accurate at time
1 Ionic MC-10-I 10" 8-3/8" 4" 10" 12 150.00 of printing. However, there may
MC-12-I 12" 10" 5-1/8" 12-1/4" 20 185.00 be some slight differences in
the future - If dimensions are
MC-6-S 6" 5-1/8" 2-1/2" 7-5/8" 5 91.25 critical, verify when placing
MC-8-S 8" 6-1/4" 3" 9-3/4" 7-1/2 130.00 your order.
2 Scamozzi
MC-10-S 10" 8-1/4" 3-5/8" 13-3/8" 15 150.00
MC-12-S 12" 9-7/8" 4-3/4" 16-1/4" 24 185.00
WE CANNOT ASSURE A
MC-8-C 6" 4-3/8" 7" 9-3/8" 8 97.00 PROPER FIT ON USE WITH
Roman MC-8-C 8" 6-1/2" 9-3/8" 11-3/8" 14 150.00 OTHER MANUFACTURER'S
3 Corinthian MC-10-C 10" 8-1/8" 11-3/16" 14-1/4" 26 210.00 COLUMNS
MC-12-C 12" 9-1/2" 13-3/4" 19-1/2" 55 250.00
68
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards
STRUCTURAL FIBERGLASS COLUMNS
Genuine marble particles are combined with polymers and fiberglass in special molds and spun into a marble-hard column
having an architecturally true taper. Virtually maintenance-free columns must be painted to assure a lifetime of beauty and
service
LARGER SIZES AVAILABLE IN PLAIN STYLE ONLY PLEASE INQUIRE
• Ideal for exterior use.
• Sharp taper for a classical look.
PART # SIZE STYLE WEIGHT PRICE EA. STRUCTURAL LOAD LIMITS
MC-68 6" x 8' PLAIN 40 lbs. 147.00 COLUMN MAXIMUM
MC-68F 6" x 8' FLUTED 40 lbs. 183.00 DIA. LOAD
MC-856 8" x 5'6" PLAIN 29 lbs. 154.00 6" 10,000 lbs.
MC-88 8"x8' PLAIN 44 lbs. 164.85 8" 10,000 lbs.
MC-88F 8"x8' FLUTED 52 lbs. 201.60 10" 14,000 lbs.
MC-89 8"x9' PLAIN 49 lbs. 172.20 12" 18,000 lbs.
MC-89F 8"x9' FLUTED 63 lbs. 224.70
MC-810 8"x10' PLAIN 50 lbs. 190.05
MC-810F 8"x10' FLUTED 66 lbs. 242.55
MC-108 10"x8' PLAIN 54 lbs. 208.95
MC-108F 10"x8' FLUTED 76 lbs. 270.90
MC-109 10"x9' PLAIN 59 lbs. 222.60
MC-109F 10"x9' FLUTED 84 lbs. 286.65
MC-1010 10"x10' PLAIN 64 lbs. 240.45
MC-1010F 10"x10' FLUTED 82 lbs. 300.30
MC-1012 10"x12' PLAIN 76 lbs. 321.30
MC-1012F 10"x12' FLUTED 84 lbs. 373.80
MC-128 12"x8' PLAIN 66 lbs. 269.85
MC-128F 12"x8' FLUTED 76 lbs. 326.55
MC-129 12"x9' PLAIN 62 lbs. 292.95
MC-129F 12"x9' FLUTED 88 lbs. 350.70
MC-1210 12"x10' PLAIN 84 lbs. 317.10
(NOTE: Decorative Caps & Bases are
MC-1210F 12"x10' FLUTED 94 lbs. 373.80
available.)
MC-1212 12"x12' PLAIN 94 lbs. 435.75
MC1212F 12"x12' FLUTED 109 lbs. 481.95
PLEASE NOTE: PRICES ABOVE INCLUDE A STANDARD POLYURETHANE CAP AND BASE.
PLEASE NOTE: Column heights listed are overall - STANDARD caps and
bases do not add to the column height.
PRICE
SHAFT
PART # SIZE (INCLUDES CAP & BASE &
WEIGHT
ASTRAGAL/BEAD)
MC-88SQ 8" X 8' 32 lbs. 264.00
MC89SQ 8" X 9' 37 lbs. 297.00
MC810SQ 8" X 10' 40 lbs. 330.00
MC108SQ 10" X 8' 41 lbs. 352.00
MC109SQ 10" X 9' 46 lbs. 396.00
MC-1010SQ 10" X 10' 51 lbs. 439.00
MC-128SQ 12" X 8' 49 lbs. 439.00
MC-129SQ 12" X 9' 55 lbs. 502.00
MC-1210SQ 12" X 10' 61 lbs. 563.00
MC1212SQ 12" X 12' 73 lbs. 659.00
FINISHING/PAINTING
Remove all dust and dirt from surface of column as well as the cap and base with either mineral spirits or denatured alcohol prior
to painting. Use a good, high quality alkyd or latex exterior paint on columns, caps, astragals (neck moulds) and bases. At least 1
coat of primer and 2 coats of final paint should be applied. Be sure to follow paint manufacturer’s instructions concerning use
within temperature ranges for best results. DO NOT use paint or solvents containing acetone.
INSTALLATION NOTES
• Be certain that the load is evenly distributed over the bearing surface of the cap and base.
• If building code requires uplift protection, contact your distributor for recommendations.
• To preserve and protect your column outdoors, it is necessary to coat with a high quality exterior primer, followed by exterior
paint.
70
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards
CLASSIC SQUARE ALUMINUM COLUMNS
STRUCTURAL INTEGRITY. . .LIFETIME DURABILITY
AVAILABLE PRIMED OR PAINTED-WHITE
LOAD BEARING STRUCTURAL MEMBERS. . .Classic columns are self supporting. . .designed as decorative, load bearing elements for
porches, entrances, driveway over hangs, etc. Ruggedly constructed, their load bearing capabilities are certified by an independent test-
ing laboratory.
PRIMED COLUMNS. . . Are coated with a mist of vinyl wash primer containing zinc chromate, ready to be finished with any good exterior
paint except lacquer.
PAINTED COLUMNS. . . Are electrostatically coated
CAP/BASE DIMENSIONS
with a baked on high-solids polyester paint, to give a
maintenance-free, uniform finish.
PLEASE NOTE. . . In addition to the diameter and heights
shown, we are also able to fabricate custom columns
according to your specifications. Please inquire
NOMINAL
PART # ACTUAL SIZE WEIGHT PLAIN*/FLUTED*
SIZE
DS68 6" x 8' 5-1/4" x 5-1/4" x 8' 8 lbs. 85.70
DS610 6" x 10' 5-1/4" x 5-1/4" x 10' 11 lbs. 112.41
DS88 8" x 8' 7-1/4" x 7-1/4" x 8' 12 lbs. 130.22
DS810 8" x 10' 7-1/4" x 7-1/4" x 10' 15 lbs. 161.39
*FOR PLAIN COLUMNS, ADD A "P" AFTER THE PART NO.; FOR FLUTED COLUMNS, ADD AN "F"
AFTER THE PART NO. (PLAIN AND FLUTED SQUARE COLUMNS ARE THE SAME PRICE)
71
ARCHITECTURAL PRODUCTS BY OUTWATER L.L.C. • Phone: 1-800-835-4400 Fax: 1-800-835-4403
CLASSIC ROUND ALUMINUM COLUMNS
STRUCTURAL INTEGRITY. . .LIFETIME DURABILITY
AVAILABLE PRIMED OR PAINTED-WHITE, ALMOND OR SANDSTONE
LOAD BEARING STRUCTURAL MEMBERS. . .Classic columns are self supporting. . .designed as decorative, load bearing elements
for porches, entrances, driveway over hangs, etc. Ruggedly constructed, their load bearing capabilities are certified by an indepen-
dent testing laboratory.
PRIMED COLUMNS. . . Are coated with a mist of vinyl wash primer containing zinc chromate, ready to be finished with any good
exterior paint except lacquer.
PAINTED COLUMNS. . . Are electrostatically coated with a baked on high-solids polyester paint, to give a maintenance-free,
uniform finish.
PLEASE NOTE. . . In addition to the diameter and heights shown, larger sizes are also available - Please inquire
EASY TO ASSEMBLE. . . (1)Before assembly, measure opening-cut column staves 1/8" longer with hacksaw. (2)To assemble, hook staves together-
small hook joins large hook. (3)Hook all staves together except one-slide remaining stave into place. (4)Put cap & base on column set in place &
plumb with level. Let weight down on column. (5)Slide cap & base into place & tighten screws.
1 2 3 4 5
72
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards
CLASSIC ALUMINUM CAPITALS & BASES
AVAILABLE PRIMED OR PAINTED - WHITE, ALMOND OR SANDSTONE
All painted capitals are available in White. Asterisks indicates availability in Almond and Sandstone.
Please use proper codes after part no. (White=WH, Almond=AL, Sandstone = SS).
Corinthian Cap
Corinthian Capitals
COLUMN PRIMED PAINTED
PART # A B C D E F
DIA. PRICE EA. PRICE EA.
*CR8COR 8" 7-3/4" 6-13/16" 12" 12-3/8" 9-1/4" 11-3/4" 248.10 250.20
*CR10COR 10" 9-1/2" 8-3/4" 14" 14-1/2" 11-1/2" 15" 368.40 371.00
CR12COR 12" 11-1/2" 10-3/4" 16-7/8" 16-7/8" 13-1/2" 18-1/2" 588.60 591.48
Scamozzi Cap
COLUMN PRIMED PAINTED
Scamozzi Cap PART #
DIA.
A B C D E F
PRICE EA. PRICE EA.
*CR8SCA 8" 7-5/8" 6-7/8" 3" 3-1/2" 8-3/4" 11-1/4" 117.70 118.70
*CR10SCA 10" 9-1/2" 8-13/16" 3-1/2" 4" 11-1/4" 14-1/4" 159.60 161.10
CR12SCA 12" 11-1/2" 10-5/8" 4" 4-3/4" 13-1/2" 18-1/2" 332.01 333.90
Decorative Base
Decorative Base COLUMN PRIMED PAINTED
PART # A B C D E
DIA. PRICE EA. PRICE EA.
*CR6DB 6" 5-3/4" 6-1/8" 8" 3" 1-5/8" 24.00 24.40
*CR8DB 8" 7-5/8" 8" 10-1/2" 4" 1-3/4" 36.60 37.10
*CR10DB 10" 9-9/16" 10-1/4" 13-1/2" 5" 2-3/8" 57.70 58.30
CR12DB 12" 11-7/16" 12-1/4" 16" 6" 3" 87.12 87.75
73
ARCHITECTURAL PRODUCTS BY OUTWATER L.L.C. • Phone: 1-800-835-4400 Fax: 1-800-835-4403
IMPORTANT NOTES REGARDING PROPER
VENTILATION & FINISHING OF WOOD COLUMNS
Prior To Storage OR Installation:
Columns must be primed twice with an oil based exterior primer and painted once with an oil based exterior
paint. The applies to shaft top, bottom, exterior and as much of interior as can be reached. Caps and bases are
polyurethane and do not require this preparatory step.
***** USE OIL BASED PRIMER & PAINTS ONLY...DO NOT USE LATEX! *****
Ventilation
Vents are cut into all bases. These allow for air to enter column interior. Do not block these vents into possible
direct water contact. Do not block these vents. It is imperative that air is allowed to escape through the capital.
This can be done in several ways. Some of the more
common methods are: A. Recessed Soffit
A. Recessed Soffit Application - (with at least a 1/2" minimum recess).
Does not require any further ventilation.
B. Flush Soffit Application - requires blocking (1/2" minimum height)
on both sides of cap vent hole, running the width of the cap.
C. Flush Ceiling - requires drilling a hole in ceiling (the same size as
and directly above cap vent hole).
Make sure the cavity that the column is exhausting into is also vented
so that air may flow freely and any condensation can dissipate.
Finishing
Fill as needed with an exterior wood putty and sand. Lightly sand between coats.
Use oil based primer and paints only...do not use latex! Prior to installation (or B. Flush Soffit
storage) prime twice (with an oil based exterior primer) shaft top, bottom,
exterior and as much of the interior that can be reached. Coat same surfaces
with one coat of an oil based exterior paint. If column is cut down, prime and
paint cut surface(s) prior to installation. After installation, column shaft, cap
and base can be finished with 1-2 coats of an oil based exterior paint.
PROPER VENTILATION AND FINISHING ARE NOT SUGGESTIONS -
THEY ARE REQUIRED FOR SUCCESSFUL INSTALLATION AND LONG
COLUMN LIFE.
Basic Column Assembly
The two most common methods of column assembly are:
1. Assembling column outside installation location
Drive several galvanized or brass screws through top of cap into top C. Flush Ceiling
of shaft, also through bottom of base into bottom of shaft. Slide
column into place and toenail/screw (using galvanized or brass fasteners)
cap and base into mounting overhead surface and floor. Plug any holes
with an exterior wood putty, sand and finish.
2. Assembling column within installation location
Drive several galvanized or brass screws through base into floor.
Do same to attach cap to overhead mounting surface. Slide shaft in
place and toenail/screw (using galvanized or brass fasteners) into
cap and base. Plug any holes with an exterior wood putty, sand and finish.
The assembly techniques shown are only the basics of installation. Location must be sound, plumb & level. Column shaft
may require to be trimmed prior to assembly. A bead of caulk/adhesive should be used on shaft ends (where shaft mounts
to cap & base) and along outside where cap, shaft & base meet. This insures a good seal between components.
74
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards
STOCK WOOD COLUMNS
Our columns are available in a kiln dried, clear, finger jointed pine or redwood. The staves are assembled using
tongue & groove joints and glued with a Type I waterproof glue, pine is dip treated with a wood preservative
and sanded. These are paint grade columns; stain grades are available as architecturally correct.
CLASSICAL
Taper 1/3 of the way up and have an architecturally correct bead moulding.
COLUMNS
COLONIAL
Taper evenly from bottom to top and have a colonial bead moulding.
COLUMNS
NON-TAPERED
Diameter does not vary, nor is there any bead moulding.
COLUMNS
All are available plain or fluted and come with a polyurethane cap
and base (unattached). Large stock columns come with a fiberglass
or polyurethane cap and base. Please check your dimensions. All
diameters are nominal. Overall height includes cap and base, all
columns require field trimming to exact height requirements.
***IMPORTANT NOTES REGARDING STOCK WOOD COLUMNS***
1. Be sure to follow all finishing and ventilation instructions, this
will insure a long life and is crucial to a successful
installation.
2. Stock columns are of a commodity grade, they will require
trimming, filling and sanding. For a select furniture grade
product, we recommend the architecturally correct columns.
They are more expensive, but are among the best on the market
today and are "finish ready".
3. Architecturally correct, redwood, large stock and altered/modified stock columns are all made to order;
they will require a deposit and production lead time. SPLITTING & SPLINING CHARGES
SPLITTING SPLIT & SPLINE
FEE FEE
PART # SIZE
PRICE PER PRICE PER
SERVICES AVAILABLE COLUMN COLUMN
PRICE PER CF9 8 FT. 15.00 80.25
DESCRIPTION PART # CF10 9 FT. 16.50 90.75
COLUMN
Exteriorizing (priming outside with 1 coat oil base prime CF12 10 FT. 18.75 101.25
N/A 8% Upcharge CF13 12 FT. 21.75 121.00
& asphaltium coat inside)
Adjust column to a specified height DR-HEIGHT/ADJ $15.00 CF14 14 FT. 26.25 141.00
Cut wood column at bead for decorative cap DR-BEAD/ADJ $15.00 CF16 16 FT. 38.25 161.25
Altering flutes from standard length DR-FLUTE/ALTER $15.00 CF18 18 FT. 57.00 181.50
Splitting for pilaster (surface mount) application SEE CHART CF20 20 FT. 73.50 202.50
Splitting & splining for reassembly around a structural post SEE CHART CF22 22 FT. 89.25 221.25
75
ARCHITECTURAL PRODUCTS BY OUTWATER L.L.C. • Phone: 1-800-835-4400 Fax: 1-800-835-4403
ROUND TAPERED
COLONIAL WOOD COLUMNS WITH POLYURETHANE CAP & BASE
PAINT GRADE/FINGER JOINTED PINE (NOT RECOMMENDED FOR STAINING)
Stock columns are of a commodity grade, they will require trimming, filling and sanding.
76
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards
RESIN CAPITALS FOR USE WITH OUR TAPERED WOOD COLUMNS
• HIGH LOAD BEARING CAPACITY • WATERPROOF • EASY TO INSTALL • INSECTPROOF
LOAD BEARING CAPACITY
DIAMETER LOAD IN POUNDS
Our capitals provide both a decorative as well as structural function. The results of independently 6 Inches 8,000
operated compressive strength testing and load bearing capacities of our capitals are listed in the chart: 8 Inches 10,000
10 Inches 12,500
12 Inches 15,000
HOW TO FINISH
It's Simple: No primer coat is necessary. Be sure to use a high quality paint and follow the manufacturer's instructions for best results.
4 3
5 1
Temple of Winds Roman Corinthian Greek Erecthium Roman Ionic Scamozzi
NAME PART # FITS OUR COLUMN DIA. BOTTOM DIA. (A) HEIGHT (B) ABACUS (C) WEIGHT IN LBS. EACH
CAP-6-I 6" 4-7/8" 2-1/4" 5-3/4" 4 81.90
Roman CAP-8-I 8" 6-5/8" 3" 7-7/8" 5-1/2 110.25
1 Ionic CAP-10-I 10" 8-3/8" 4" 10" 12 137.55
CAP-12-I 12" 10" 5-1/8" 12-1/4" 20 176.40
78
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards
ROUND TAPERED
CLASSICAL WOOD COLUMNS WITH POLYURETHANE CAP & BASE
PAINT GRADE/FINGER JOINTED PINE (NOT RECOMMENDED FOR STAINING)
Stock columns are of a commodity grade, they will require trimming, filling and sanding.
79
ARCHITECTURAL PRODUCTS BY OUTWATER L.L.C. • Phone: 1-800-835-4400 Fax: 1-800-835-4403
PermaPost™
SYNTHETIC PORCH POSTS
❑ Weatherproof &
Insectproof
❑ Shipped White,
Ready to Install
❑ Must Be Painted
With Latex or Oil
Based Paint
❑ Low Maintenance
80
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards
PVC POST COVER
FOR 4” x 4” or 6” x 6” POSTS
Protects & Beautifies Unsightly Wood Posts
• Covers posts up to 9 feet tall
• Simple to install
• Inexpensive
• Maintenance Free
• Strong, Resilient, Exterior Grade PVC
• Easy to clean
• Available in White
• Two trim collars with each post cover
(Trim collars come as a 4 pc. set, PVC
glue is recommended to join pcs. together).
SPECIFICATIONS
PPC-49 PPC-69
MATERIAL PVC PVC
MATERIAL THICKNESS 1/8" 1/8"
WALL THICKNESS 5/16" 5/16"
INSIDE DIMENSIONS 3-3/4" 5-5/8"
OUTSIDE DIMENSIONS 4-5/16" 6-3/16"
BEFORE AFTER
PART # FOR POST SIZE DESCRIPTION PRICE
PPC-49-WH 4" x 4" 9 Ft. Long Cover & 2 Trim Collars 43.00
PPC-TC-4-WH 4" x 4" Additional Trim Collar 4.90
PPC-69-WH 6" x 6" 9 Ft. Long Cover & 2 Trim Collars 58.00
PPC-TC6-WH 6" x 6" Additional Trim Collar 5.45
Installation Instructions:
1. Measure & cut both sides to length.
2. Wrap post with pieces and starting at the bottom, snap
pieces together. (We recommend you hold one side
against the post while tapping the other side in with a
rubber mallet).
3. Glue trim collar sides to each other and post cover. Use PVC
glue only.
TOP VIEW (4 interlocking pieces)
81
ARCHITECTURAL PRODUCTS BY OUTWATER L.L.C. • Phone: 1-800-835-4400 Fax: 1-800-835-4403
ARCHITECTURAL PRODUCTS INTRODUCES OUR NEW LINE OF
Paintable
#PCOV-PG-CB
$31.00 kit Paint Grade MDF
#PCOV-PG
Knotty Pine (Knotty Pine) $89.00 ea.
#PCOV-KP-CB
$35.00 kit
Knotty Pine
#PCOV-KP
Red Oak $149.00 ea.
#PCOV-RO-CB
$39.00 kit Red Oak
#PCOV-RO
(Cap Trim Detail)
(Red Oak) $159.00 ea.
*** Cap & Base Trim Kits Need To Be Assembled & Attached To Post On Site ***
82
VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards