Professional Documents
Culture Documents
For installation on adjustable handlebar, kit (P/N 219 400 408) is required.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION Indicates a hazard situation which, if not avoided, could result in minor or moderate injury.
NOTICE Indicates an instruction which, if not followed, could severely damage vehicle components or other property.
WARNING
For safety reasons, this kit must be installed by an authorized BRP dealer.
This kit is designed for specific applicable models only (authorized BRP dealers will confirm model(s)). It is not recommended for units other than the one (those) for which it was sold.
This instruction sheet MUST be given to the purchaser.
Should removal of a locking device (e.g. lock tabs, self-locking fasteners, etc.) be required when undergoing disassembly/assembly, always replace with a new one.
Torque wrench tightening specifications must strictly be adhered to.
NOTE: The illustrations in this document show typical construction of the different assemblies and may
not reproduce the full detail or exact shape of the parts; however, they represent parts that have the
same or similar function.
Installation time is approximately 1.5 hour.
ICON LEGEND
ICON
INDICATES
Parts to be discarded
1 / 17
PARTS TO BE INSTALLED
PARTS TO BE INSTALLED
ITEM
2 / 17
DESCRIPTION
PART NUMBER
GPS
NAVIGATION
SYSTEM
GPS
MOUNTING
KIT
P1
GPS Navigation
System
P1a
GPS Protective
Pouch
Not Available
Separately
P1b
Not Available
Separately
P2
P3
GPS Support
Not Available
Separately
P4
GPS Holder
Protector
P5
M10 x 70
Hexagonal
Screw
Not Available
Separately
P6
M4 x 16 Torx
Screw
P7
M4 x 25 Torx
Screw
P8
M4 Flat Washer
P9
Plastic Cap
P10
Audio Harness
(Spyder RT and
Spyder ST with
audio system)
P12
12V Feed
Harness (Spyder
RS and ST
without audio
system)
PARTS TO BE INSTALLED
PART NUMBER
GPS
NAVIGATION
SYSTEM
GPS
MOUNTING
KIT
P13
Universal Audio
Harness (for
GPS Navigation
Systems other
than BRP)
Not Available
Separately
P14
Universal
12V Feed
Harness (for
GPS Navigation
Systems other
than BRP)
Not Available
Separately
P15
M10 x 40
Hexagonal
Screw
ITEM
DESCRIPTION
3 / 17
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Vehicle Preparation
All Models
Refer to appropriate shop manual and remove:
Upper RH side panel
RH side panel.
Remove and discard center cap and handlebar rear retaining screws.
rsi2014-011-001
Spyder RT Models
INSTALLATION INSTRUCTIONS
rsi2014-011-002
1. Lift up handlebars to allow passage of [P2] harness or GPS harness from other GPS system
2. Route [P2] harness or GPS harness from other GPS system
5 / 17
INSTALLATION INSTRUCTIONS
P2
1.5 0.5 Nm
P7
P7
P9
P3
1
1.5 0.5 Nm
P7
P7
P8
P8
rsi2013-031-125_a
1. GPS holder [P2] harness or GPS harness from other GPS system
P15
P1
P5
P5
1
rsi2014-011-003
6 / 17
INSTALLATION INSTRUCTIONS
P2
1.5 0.5 Nm
P7
P7
P3
1.5 0.5 Nm
P7
P7
P8
P8
rsi2013-031-123_a
1.5 0.5 Nm
P7
P7
1
1.5 0.5 Nm
P7
P7
1
P8
P8
rsi2013-031-126_a
7 / 17
INSTALLATION INSTRUCTIONS
P2
1.5 0.5 Nm
P7
P7
1.5 0.5 Nm
P7
P7
1
2
rsi2013-031-127_a
rsi2013-031-113_a
Choose appropriate harness depending on vehicle configuration, see illustrations below for reference.
8 / 17
INSTALLATION INSTRUCTIONS
Spyder RT and Spyder ST Models with Audio System (For BRP GPS Navigation System)
2
1
3
rsi2013-031-114_a
9 / 17
INSTALLATION INSTRUCTIONS
4
2
rsi2013-031-116_a
10 / 17
INSTALLATION INSTRUCTIONS
Spyder RS and Spyder ST Models without Audio System (For BRP GPS Navigation System)
2
1
2
1
rsi2013-031-115_a
rsi2013-031-133_a
11 / 17
INSTALLATION INSTRUCTIONS
P12
rsi2013-031-134_a
LH SIDE
1. Vehicle main harness
Spyder RT and Spyder ST with Audio System (For GPS Navigation Systems other than BRP)
rsi2013-031-118_a
12 / 17
INSTALLATION INSTRUCTIONS
NOTE: If the GPS navigation system is not equipped with audio connector, simply cover the input cable
P1
P8
P7
P11
2
P7
1
P7
1 1
11
P4
P13
11
P11
R
rsi2013-031-094_a
NOTE: Make sure both harnesses overlap at the thin line to guarantee a solid bonding between wires.
Using a heat gun, heat until tin has melted and plastic has shrunk over the wires.
13 / 17
INSTALLATION INSTRUCTIONS
rsi2013-031-119_a
Spyder RS and Spyder ST without Audio System (For GPS Navigation Systems other than BRP)
rsi2013-031-120_a
14 / 17
INSTALLATION INSTRUCTIONS
P14
R
rsi2013-031-121_a
NOTE: Make sure both harnesses overlap at the thin line to guarantee a solid bonding between wires.
Using a heat gun, heat until tin has melted and plastic has shrunk over the wires.
P14
rsi2013-031-122_a
LH SIDE
1. Vehicle main harness
15 / 17
INSTALLATION INSTRUCTIONS
P1
P2
rsi2013-031-135_a
P1b
rsi2013-031-137_a
16 / 17
INSTALLATION INSTRUCTIONS
P4
P9
P1b
1
1
rsi2013-031-131_a
CAUTION The rubber boot must be installed at all times except when the GPS is installed onto
the vehicle.
17 / 17