You are on page 1of 18

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

16 Common 3D Printing Problems and


Solutions
November 12, 2015 Franz Grieser 3D Printing Tutorial

Filament

Looking for a 3D printer troubleshooting guide to avoid common 3D printing


issues? These are the 16 most common 3D printing problems and their solutions.
Read how and when they occur and what you can do to avoid them in the future.

3D Printing Problems #1: Warping

Warping: The front corner of this pyramid has lifted up.

Whats the problem? At the base of the model, one or more corners lift up so they
are no more level with the print platform. This can also result in horizontal cracks in
upper parts.

1 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

Whats the cause? Warping is a common 3D printing problem, it happens when


the plastic of the first layers cools down and thus starts to shrink. This causes the
edges of the model to bend up.
What to do about it? There are several things you can do:
1.

Use a heated print bed to keep the plastic at a temperature just below the
point where it gets solid this is called the glass transition temperature.
This way, the first layer stays flat on the print bed.

2.

Increase adhesion of the first layer to the print bed by spreading a tiny film
of glue evenly on the bed.

3.

Make sure the print bed is levelled perfectly.

4.

You may consider adding a raft or pads to increase platform adhesion.

Even if your printer has a heated bed, we recommend you use glue and level the
bed.
Image source: Rudor on Flickr

3D Printing Problems #2: Elephant Foot

Not easy to spot in the photo: the bulges at the base.

Whats the problem? The base of the model (i.e., the first layers) is wider than
wanted.

2 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

Whats the cause? To avoid warping, users often increase first layer squish. This
may result in the base bulging out thats why this effect is called elephant foot.
This ungainly effect can also be caused by the weight of the rest of the model
pressing down the first layers, when the lower layers havent had time to get solid
in particularly, when your printer has a heated bed.
What to do about it? In 3D printing troubleshooting guides, this is probably the
most-discussed 3D printing problem. Its not easy to find the right balance between
getting rid of warping and avoiding the elephant foot effect. To minimize bulges at
the base of your model we recommend levelling the printer bed and moving the
nozzle a little further away from the bed (but not too far, otherwise the print will not
stick); additionally, lower the bed temperature slightly.
If you create the 3D model yourself, put a small chamfer at the bottom of the model.
Start with a 5mm and 45 chamfer and experiment to get the best result.
Image source: Walter Gordy at Flickr

3D Printing Problems #3: More First Layer Problems

3 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

Right: Uneven first layer; left: warping because of the small footprint.

Whats the problem?


The first layer does not stick properly; as a result some parts come loose.
There are unwanted lines at the bottom.
Whats the cause? These 3D printing problems are typical signs that the print bed
has not been levelled properly. If the nozzle is too far away from the bed, the
bottom surface often shows unwanted lines, and/or the first layer does not stick. If
the nozzle is too close, blobs may be the result.
Also, the print bed has to be as clean as possible: Finger prints on the plate can
prevent the first layer to stick to the plate.
What to do about it?
1.

Use your printer software to re-level the print bed.

2.

Clean the bed of finger prints.

3.

Apply a fine film of glue before printing.

Image source: Richard H on Flickr

3D Printing Problems #4: Lower Parts Shrink


Whats the problem? The lower part of the model caves in.
Whats the cause? This happens when the temperature of the heat bed is too
high.
Plastic being heated and extruded behaves like a rubber band: First, it expands,
when cooling down, it shrinks. The heat from the bed only rises to a certain height
(depending on the temperature). Up to this height, the extruded plastic stays warm

4 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

and malleable longer than the plastic layers above the height. This way it may
yield under the weight of the upper layers and cave in.
What to do about it? Heres 3D printing troubleshooting 101: Reduce bed heat! In
some printers, the default bed temperature is 75C, the recommended temperature
for PLA, however is 50-60C. Additionally, set the fan in the printer to fully blow at
the lowest height.
When printing small models, we recommend you print two copies or two differenct
objects. This way the print head will take more time to print one layer after the
other.
When printing models with a large footprint, do not reduce bed temperature
otherwise the edges may warp.

3D Printing Problems #5: Skewed Prints Shifted Layers


Leaning

Shifted layers in Fred Kahls 3D printer hangover

5 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

Whats the problem? The upper layers are shifted.


Whats the cause? This is caused by the printer:
The head does not move easily on the X or Y rods.
The rods are not aligned correctly, i.e., they are not 100% square.
One of the pulleys is not fixed properly to the axis.
What to do about it?
1.

Turn the printer off and check whether you can move the head easily along
the rods with your hands. If the head moves stiffly or it moves more easily in
one direction, apply a drop of sewing machine oil to the rod (or the rod along
the head moves more stiffly).

2.

To see, if the rods are correctly aligned: Moving the head to the left and the
right side of the printer and check that the distance between the sliding
blocks and the pulleys are equal on both sides. Repeat this for the
front/back of the printer. If you notice misalignment, loosen the screws on
the two pulleys of the rod in question. Nudge the sliding block a bit until the
rod is aligned again, then tighten the screws. Repeat for the other rod.

3.

Check to see if the screws that hold the pulleys in place are tight. If
necessary, tighten them.

Image source: Fred Kahl on Flickr

3D Printing Problems #6: Layer Misalignment

6 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

Flawed layer alignment.

Whats the problem? Some layers in the middle of the objects have shifted.
Whats the cause?
The printer belts are not well tightened.
The top plate is not fastened and wobbles around independent of the
bottom plate.
One of the rods in the Z axis is not perfectly straight.
What to do about it?
This is our 3D printing troubleshooting suggestion:
1.

Check the belts and re-tighten them, if necessary.

2.

Check the top plate and fasten it, if necessary.

3.

Check the Z axis rods and replace those that are not 100% straight.

Image source: Sladuuch on Flickr

3D Printing Problems #7: Missing Layers


Whats the problem? There are gaps, since some layers have been skipped (in

7 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

part or completely).
Whats the cause?
For some reasons the printer failed to provide the amount of plastic
required for printing the skipped layers. This is called (temporary)
underextrusion. There may have been a problem with the filament (e.g. the
diameter varies), the filament spool, the feeder wheel or a clogged nozzle.
Friction caused the bed to temporarily get stuck. The cause: The vertical
rods are not perfectly aligned with the linear bearings.
There is a problem with one of the Z axis rods or bearings: The rod could
be distorted, dirty or had been oiled excessively.
What to do about it?
1.

Check the rods and bearing for problems and fix them. If there is too much
oil, for example, remove it.

2.

If you suspect misalignment of rods and bearings, consult your printers


documentation to see how to correct that.

3.

Finding the cause for underextrusion is more cumbersome. See 3D Printing


Problems #11.

3D Printing Problems #8: Cracks In Tall Objects


Whats the problem? There are cracks on the sides, especially on tall models.
Whats the cause? In higher layers, the material cools faster because the heat of
the heat bed does not reach that high. This way, adhesion in the upper layers is
lower.
What to do about it? Increase the extruder temperature a good start is
increasing it by 10C. Also increase the bed temperature by 5-10C.

8 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

3D Printing Problems #9: Pillowing

Pillowing: The top surface shows bumps and/or holes.

Whats the problem? The top surface shows bumps or even holes.
Whats the cause?
The typical cause for this 3D printing problem is improper cooling.
The top surface is not thick enough.
What to do about it?
1.

Set the cooling fans to top speed when the top surfaces are printed.

2.

Make sure the top surfaces are at least 6 layers thick.

Image source: Ultimaker

3D Printing Problems #10: Stringing

9 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

Stringing: Unwanted strings of plastic between the parts of the object.

Whats the problem? There are unwanted thin strings of plastic between parts of
the model.
Whats the cause? When the print head moved over an open part (so-called travel
move), some filament dripped from the nozzle.
What to do about it? Most printers have a feature called retraction. When
retraction has been enabled, the printer retracts the filament in the nozzle before
travel moves. This way, no surplus plastic can drip from the nozzle and produce
strings. So: Make sure you enable retraction in the slicing software for your printer.
One of the easier 3D printing problems.
Image source: Ultimaker

3D Printing Problems #11:Underextrusion


Whats the problem? Underextrusion means that the printer cannot supply the
material needed (or as fast as needed). Underextrusion results in thin layers, in
layers with unwanted holes, or in missing layers (see 3D Printing Problems #7).
Whats the cause? There are several possible causes:

10 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

The diameter of the filament used does not match the diameter set in the
slicing software.
The amount of material that is extruded is too low because of faulty slicer
software settings.
The flow of the material through the extruder is restricted by dirt in the
nozzle.
What to do about it?

In Simplify3D, you set the filament diameter in the Edit Process Settings dialog.

1.

Check the filament diameter and the diameter setting in the slicing software
correct the software setting, if necessary. The filament diameter is printed
on the spool or on the package: if not, measure it using calipers.

2.

If there is no mismatch between actual filament diameter and the software


setting, the extrusion multiplier (or flow rate or flow compensation) setting
may be too low. Increase the setting in 5% steps and restart printing. In
Simplify3D open the Edit Process Settings dialog and go to the Extruder tab
the Extrusion multiplier setting of 1.0 corresponds to 100%; in Cura
open the Material tab and increase the Flow setting (you may need to
enable the Flow setting through the Preferences dialog).

3.
11 di 18

Check to see if there is a partial blockage in the nozzle and remove it.
12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

3D Printing Problems #12: Overextrusion

A Flow setting way over 100% in Cura may result in overextrusion; the Flow setting (right) is only visible when you
check the Flow option in the Preferences (left).

Whats the problem? Overextrusion means that the printer supplies more material
than needed. This results in excess material on the outside of the model printed.
Whats the cause? Typically, the Extrusion multiplier or Flow setting in your
slicing software is too high (see the section above)
What to do about it? Correct the Extrusion multiplier or Flow setting in your
printers software.

3D Printing Problems #13: Gaps in the Top Layers


Whats the problem? There are holes or gaps in the top layers.
Whats the cause? To save print material and to speed printing, the interior of a
model is not printed 100% solid. Instead, some kind of infill is printed, typically only
30% of the material, the rest of the model remains hollow. Only the top layers (and
the walls and the bottom) are printed 100% solid. The are gaps in the top layers can
have these causes:

12 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

There are too few solid top layers.


The infill percentage (for the interior) is too low.
Underextrusion (see 3D Printing Problems #11).
What to do about it?
1.

The first corrective measure when you notice holes or gaps in the top
surface: Increase the number of solid top layers in the slicing software.
There should be at least 0.5mm of solid layers (how many layers that means
depends on the layer height). The additional solid top layers do not add
height to your printed model. When you increase the number from 3 to 5, for
example, the last 5 layers are printed solid (instead of 3).
In Simplify3D, you increase the number of solid layers on the Layer tab in
the Edit Process Settings dialog. In Cura, use the Shell Thickness setting
on the Quality tab to increase the solid top layers (plus the solid bottom
layers and the outside walls).

2.

When the hollow gaps in the model are too wide, because the infill
percentage is only say 10 or 20% the solid layers may sag. If adding
more solid top layers does not correct the problem, increase the infill
percentage in the slicing software. This will increase the filament
consumption.
In Simplify3D, the infill options are found on the Infill tab in the Edit
Process Settings dialog. In Cura, youll find the Infill Density setting on the
Infill tab.

3.

To correct underextrusion: see 3D Printing Problems #11.

3D Printing Problems #14: Visible Lines in the Bottom


Layers
Whats the cause? The gap between the nozzle and the printbed is too big. So
what can you do for 3D printing troubleshooting?
What to do about it?

13 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

In Cura, you can increase the thickness of outer walls and the top and bottom layers.

1.

Make sure your printbed is levelled correctly.

2.

Reduce the height of the very first layer depending on your printer and the
filament used, you may go down to 0.1mm (this, however, requires that the
printbed is absolutely level).

See All3DPs guide on how to get better results in 3D printing to learn how to level
the printbed and adjust the gap between the nozzle and the printbed.

14 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

3D Printing Problems #15: Scars on the Top Surface


Whats the cause? The marks are caused by the nozzle that moved across the top
surface.
They are actual scratches as the nozzle scrapes over the surface.
These marks are plastic oozing caused when the nozzle travelled across
the surface (but did not touch the surface).

What looks like scratches is in fact oozing of the filament when the printhead travelled over the piece.

What to do about it?

15 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

For the example above the, the Retraction Vertical Lift value in Simplify3D was too low.

1.

To avoid scratches and reduce oozing: Increase the vertical lift (or Z-hop)
setting for your printer. This setting controls how far the nozzle is lifted up
above the last layer printed when travelling (without printing). In Simplify3D,
you change this setting on Extruder tab of the Edit Process Settings
dialog; make sure the Retraction option is enabled and increase the
Retraction Vertical Lift setting. In Cura, set Enable Retraction and
Retraction Distance (in the Preferences dialog) and increase the
Retraction Distance value on the Material tab.

2.

To reduce oozing more, force the printer to do a retraction before a travel


move. In Simplify3D, disable the Only retract when crossing open spaces
and Minimum travel for retraction options on the Advanced tab on the Edit
Process settings dialog. In Cura, set the Minimum Travel Distance to 1
and Minimum Extrusion to 0. Please note that this will increase print time.

3D Printing Problems #16: No Print Material is Getting Out


Of the Nozzle
Whats the cause?
The nozzle is clogged by carbonized material from previous print

16 di 18

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

processes.
There is a problem with the feeder. The feeder motor may be defective, the
pressure the feeder puts on the filament is too low or the filament has
ground.
What to do about it?
1.

If the nozzle is clogged, clean it according to the printer manufacturers


instructions.

2.

If the motor is defective, have it replaced.


Consult the printers documentation to see how and where to change the
pressure settings and check whether the settings are correct.
If the filament has ground, replace it.

The text of "16 Common 3D Printing Problems and Solutions" by All3DP is licensed under a Creative
Commons Attribution 4.0 International License.

If you enjoyed reading this story, then like our page on Facebook.

Topics
3D Printing Tutorial

17 di 18

Filament

12/03/2016 00:06

16 Common 3D Printing Problems and Solut...

https://all3dp.com/common-3d-printing-pro...

Imprint
Privacy Policy
About us
We want your feedback!

18 di 18

12/03/2016 00:06

You might also like