Professional Documents
Culture Documents
High Performance
Guided Wave Radar
Level Transmitter
DESCRIPTION
The new Eclipse Model 706 High Performance Transmitter
is a loop-powered, 24 VDC level transmitter that is based
upon the proven and accepted technology of Guided
Wave Radar (GWR). Encompassing a number of significant engineering accomplishments, this leading edge level
transmitter is designed to provide measurement performance well beyond that of many of the more traditional
technologies.
APPLICATIONS
MEDIA: Liquids, solids, or slurries; hydrocarbons to waterbased media (Dielectric Constant r = 1.2100)
VESSELS: Most process or storage vessels up to rated
probe temperature and pressure.
CONDITIONS: All level measurement and control applications including process conditions exhibiting visible
vapors, foam, surface agitation, bubbling or boiling, high
fill/empty rates, low level and varying dielectric media or
specific gravity.
FEATURES
Multivariable, two-wire, 24 VDC loop-powered transmitter for level, interface, volume, or flow.
Diode switching technology offers best-in-class signal
strength and signal-to-noise ratio (SNR) resulting
in enhanced capability in difficult low dielectric
applications.
Level measurement not affected by changing media
characteristics.
No need to move levels for calibration.
Overfill Capable probes allow for true level measurement all the way up to the process seal, without
the need for special algorithms.
4-button keypad and graphic LCD display allow for
convenient viewing of configuration parameters and
echo curve.
Proactive diagnostics advise not only what is wrong,
but also offer troubleshooting tips.
Nine common tank shapes for volumetric output.
TECHNOLOGY
PRINCIPLE OF OPERATION
ECLIPSE Guided Wave Radar is based upon the technology
of TDR (Time Domain Reflectometry). TDR utilizes pulses
of electromagnetic energy transmitted down a wave guide
(probe). When a pulse reaches a surface that has a higher
dielectric constant than the air (r = 1) in which it is traveling, a portion of the pulse is reflected. The transit time
of the pulse is then measured via high speed timing
circuitry that provides an accurate measure of the liquid
(or solids) level. The amplitude of the reflection depends
on the dielectric constant of the product. The higher the
dielectric constant, the larger is the reflection.
Initial
Initial
Pulse
Initial
Initial
Pulse
Pulse
Reflected
Reflected
Pulse
Pulse
Air r =
=1
Air
r 1
Air
Air
rr==11
rr > 1,2
1.2
Reflected
Reflected
Pulse
Pulse
1.2
Liquid rr >> 1,2
Transmitted
Transmitted
Pulse
Pulse
Transmitted
Transmitted
Pulse
Pulse
INTERFACE MEASUREMENT
The ECLIPSE Model 706 is capable of measuring both an
upper liquid level and an interface liquid level. As only a
portion of the pulse is reflected from a low dielectric upper
surface, some of the transmitted energy continues down
the GWR probe through the upper liquid. The remaining
initial pulse is again reflected when it reaches the higher
dielectric lower liquid. It is required that the upper liquid
has a dielectric constant less than 10, and the lower liquid
has a dielectric constant greater than 15. A typical interface
application would be oil over water, with the upper layer
of oil being non-conductive (r 2.0), and the lower layer
of water being very conductive (r 80). The thickness of the
upper layer could be as small as 50 mm (2") while the maximum upper layer is limited to the length of the GWR probe.
2
Reference
Reference
signal
Signal
Air
Airr =r1=
Upper level
Upper level
signal
(e.g. oil, r = 2)
signal
Emulsion
layer
Emulsion
Interface
Interface
level signal
level signal
Time
Time
Interface Level
SPECIAL
APPLICATIONS
EMULSION LAYERS
OVERFILL CAPABILITY
Knowing exactly where the target is located at room temperature, and then continuously monitoring its apparent
location, the vapor space dielectric can be back-calculated.
Knowing the vapor space dielectric, accurate compensation of the actual liquid level reading is accomplished.
This is a patented technique with two US Patents
(US 6642801 and US 6867729) issued for both the mechanical target concept and the associated software algorithm.
Contact the factory for additional information relating to
saturated steam applications.
PROBE
THREE
OVERVIEW
STYLES
OF
GWR
PROBES
With one basic ECLIPSE Model 706 transmitter that operates with all probes, choosing the proper Guided Wave
Radar (GWR) probe is the most important decision in the
application process. The probe configuration establishes
fundamental performance characteristics.
All ECLIPSE Model 706 probes can be described by three
basic configurations:
Coaxial
Twin flexible cable
COAXIAL PROBES
The efficiency and overall sensitivity of a coaxial configuration yields robust signal strength, even in extremely low
dielectric (r 1.4) applications. The sensitivity of this
Figure 1
Coaxial Probe
PROBE
THREE
OVERVIEW
STYLES
OF
CONTINUED
GWR
PROBES
OPTIONAL FLUSHING
CONNECTION
The maintenance of coaxial GWR probes in applications
suffering from buildup or crystallization can be significantly improved by using an optional flushing connection.
This flushing connection is a metal extension with a port
welded above the process connection. The port allows
the user to purge the inside of the coaxial GWR probe
during routine maintenance.
Note: The best approach to eliminate the effects of
condensation or crystallization is to install
adequate insulation or heat tracing (steam or
electrical). A flushing connection is no substitute for proper maintenance, but will help
to reduce the frequency of the intervention.
Flushing Port
Shown Plugged
(14 NPT-F)
OPTIONAL ANNUNCIATOR
FITTING
High Pressure and High Temperature High Pressure
ECLIPSE Model 706 probes containing a glass ceramic
alloy process seal (Models 7yD, P, J, L, M and N) are available with an optional annunciator fitting. The use of this
fitting complies with the Dual Seal requirements of
PROBE
THREE
OVERVIEW
STYLES
OF
CONTINUED
GWR
PROBES
Figure 2 also shows that, although most of the electromagnetic field develops between the two cables, there is also
some peripheral energy that expands outward, making the
Twin Cable probe more sensitive to proximity effects of
objects located immediately around it. For that reason, it is
recommended to keep the active element of the Twin Cable
probe at least 25 mm (1") away from metal objects.
Figure 2
Twin Flexible Probe
Figure 3
Single Rod Probe
Launch Plate
PROBE
SELECTION
GUIDE
TWIN CABLE GWR PROBE
signal propagation
signal propagation
Lau
end view
GWR
Description
Probe
7yT
7yP
7yD
7yS
7yG
7yL
7yJ
7yF
7yM
7yN
Application
end view
Installation
Dielectric
Range
Temperature
Range
Max.
Overfill
Vacuum
Pressure
Safe
70 bar
(1000 psi)
431 bar
(6250 psi)
431 bar
(6250 psi)
88 bar
(1275 psi)
Standard
Temperature Level/Interface
High
Pressure Level/Interface
High Temp./ Level/Interface
High Press.
70 bar
(1000 psi)
431 bar
(6250 psi)
431 bar
(6250 psi)
Standard
Temperature
High
Pressure
High Temp./
High Press.
Level
Level
Level
Standard
7y1 Temperature
Level
7y3 High Temp./
Level
High Press.
Standard
7y4
Temperature Level/Interface
7y6 High Temp./ Level/Interface
High Press
7y7
Standard
Temperature Level/Interface
7y2
Bulk Solids
Probe
7y5
Bulk Solids
Probe
Level
Level
Viscosity
cP (mPa.s)
Yes
Yes
500/2000
Full
Yes
500/2000
Full
Yes
500/2000
Full
No
500
Yes
Yes
10000
Full
Yes
10000
Full
Yes
10000
Yes
No
10000
Full
No
10000
Full
No
10000
Yes
No
10000
Full
No
10000
Yes
No
10000
Full
No
10000
Yes
No
1500
No
No
10000
No
No
1500
TRANSMITTER
SPECIFICATIONS
FUNCTIONAL/PHYSICAL
System Design
Measurement Principle
Input
Measured Variable
Span
Output
Type
Resolution
Analog:
Digital Display:
.003 mA
1 mm
Loop Resistance
Diagnostic Alarm
Selectable: 3.6 mA, 22 mA (meets requirements of NAMUR NE 43), or HOLD last output
Diagnostic Indication
Damping
User Interface
Keypad
Display
Digital Communication/Systems
Menu Languages
Housing
Material
Net/Gross Weight
Overall Dimensions
Cable Entry
TRANSMITTER
SPECIFICATIONS
CONTINUED
FUNCTIONAL/PHYSICAL
Environment
Operating Temperature
-40 to +80 C (-40 to +175 F); LCD viewable -20 to +70 C (-5 to +160 F)
Storage Temperature
Humidity
0 to 99 %, non-condensing
Electromagnetic Compatibility
Surge Protection
Shock/Vibration
Performance
Reference Conditions
Linearity
Coaxial/Caged Probes:
Coaxial/Caged Probes:
Interface Operation:
Resolution
0.1 mm or 1"
Repeatability
<2,5 mm (0.1")
Hysteresis
<2,5 mm (0.1")
Response Time
Approximately 1 second
Initialization Time
Approx. 0.02 % of probe length/C (for probes greater than 2,5 m (8'))
Process Dielectric
FOUNDATION fieldbus
ITK Version
6.1.1
H1 Device Class
H1 Profile Class
31PS, 32L
Function Blocks
(8) Al, (3) Transducer, (1) Resource, (1) Arithmetic, (1) Input Selector,
(1) Signal Characterizer, (2) PID, (1) Integrator
Quiescent Current
15 mA
Execution Time
COAXIAL
PROBE
MATRIX
7yT
7yP
Description
Standard Temperature
High Pressure
Application
Level/Interface
Level/Interface
Installation
Tank/Chamber
Tank/Chamber
Overfill Safe
Yes
Yes
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
Teflon TFE
Teflon TFE
Materials Probe
Process Seal
Spacers
Probe Outside Diameter
Enlarged
Basic
Process Connection
Threaded
Flanged
Available Probe Length
Standard
Enlarged
Transition Zones
Top
Bottom
0 mm (0")
0 mm (0")
Process Temperature
70 bar @ +20 C (1000 psi @ +70 F) 431 bar @ +20 C (6250 psi @ +70 F)
Dielectric Range
Vacuum Service
1.4 to 100
1.4 to 100
Negative Pressure,
but no hermetic seal
Full Vacuum
2000cP (mPa.s)
500cP (mPa.s)
2000cP (mPa.s)
500cP (mPa.s)
Filming
Filming
Viscosity
Enlarged
Basic
Media Coating
10
COAXIAL
PROBE
MATRIX
CONTINUED
7yD
7yS
Description
Steam Probe
Application
Level/Interface
Saturated Steam
Installation
Tank/Chamber
Tank/Chamber
Overfill Safe
Yes
No
Materials Probe
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Process Seal
PEEK HT/Ceramic
PEEK HT/Ceramic
N/A
22,5 mm (0.87")
Spacers
Probe Outside Diameter
Enlarged
Basic
Process Connection
Threaded
Flanged
200 mm (8")
r = 80: 50 mm (2")
Process Temperature
431 bar @ +20C (6250 psi @ +70 F) 87,9 bar @ +300C (1275 psi @ +575 F)
Top
Bottom
Dielectric Range
1.4 to 100
10 to 100
Vacuum Service
Full Vacuum
Full Vacuum
2000cP (mPa.s)
500cP (mPa.s)
N/A
500cP (mPa.s)
Filming
Filming
Viscosity
Enlarged
Basic
Media Coating
Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 %
measuring range outside of the transition zones.
Refer to chart on page 16.
ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with
glass seal are hermetically sealed to <10-8 cc/sec @ 1 atmosphere helium.
Can be reduced to 75 mm (3") when lower accuracy is acceptable.
1.2 minimum dielectric when end of probe analysis is enabled.
Consult factory for overfill applications.
11
CAGED
PROBE
MATRIX
7yG
7yL
7yJ
Description
Standard Temperature
High Pressure
Application
Level/Interface
Level/Interface
Level/Interface
Installation
Chamber
Chamber
Chamber
Yes
Yes
Yes
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
PEEK
PEEK
PEEK HT/Celazole
Overfill Safe
Materials Probe
Process Seal
Spacers
Probe Outside Diameter
13 mm (.5") to 19 mm (.75")
13 mm (.5") to 19 mm (.75")
13 mm (.5") to 19 mm (.75")
2" Chamber
3" Chamber 19 mm (.75") to 29 mm (1.13") 19 mm (.75") to 29 mm (1.13") 19 mm (.75") to 29 mm (1.13")
4" Chamber 27 mm (1.05") to 38 mm (1.50") 27 mm (1.05") to 38 mm (1.50") 27 mm (1.05") to 38 mm (1.50")
Process Connection
Flanged
Transition Zones
Top
Bottom
Process Temperature
Max. Process Pressure
0 mm (0")
0 mm (0")
0 mm (0")
70 bar @ +20 C (1000 psi @ +70 F) 431 bar @ +20 C (6250 psi @ +70 F) 431 bar @ +20 C (6250 psi @ +70 F)
Dielectric Range
1.4 to 100
1.4 to 100
1.4 to 100
Vacuum Service
Negative Pressure,
but no hermetic seal
Full Vacuum
Full Vacuum
10,000cP (mPa.s)
10,000cP (mPa.s)
10,000cP (mPa.s)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Viscosity
Media Coating
12
SINGLE
ROD
RIGID
PROBE
MATRIX
7yF
7yM
7yN
Description
Standard Temperature
High Pressure
Application
Level
Level
Level
Installation
Tank
Tank
Tank
No
No
No
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
PFA Insulated 316/316L rod
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
316/316L (1.4401/1.4404)
Hastelloy C (2.4819)
Monel (2.4360)
None
None
PEEK HT/Celazole
2 (NPT or BSP)
Various ANSI, EN1092, and
proprietary flanges
Overfill Safe
Materials Probe
Process Seal
Spacers
Probe Outside Diameter
Process Connection
Threaded
Flanged
Available Probe Length
Transition Zones
Top
Bottom
Process Temperature
Max. Process Pressure
Dielectric Range
Vacuum Service
Viscosity
Media Coating
Application Dependent
Application Dependent
Application Dependent
70 bar @ +20 C (1000 psi @ +70 F) 431 bar @ +20 C (6250 psi @ +70 F) 431 bar @ +20 C (6250 psi @ +70 F)
1.7 to 100
1.7 to 100
1.7 to 100
Negative Pressure,
but no hermetic seal
Full Vacuum
Full Vacuum
10,000cP (mPa.s)
10,000cP (mPa.s)
10,000cP (mPa.s)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
13
FLEXIBLE
PROBES
FOR
LIQUIDS
MATRIX
7y1
7y3 (Future)
Description
Single Flexible
Standard Temperature
Single Flexible
HTHP
Application
Level
Level
Installation
Tank
Tank
No
No
316 (1.4401)
316 (1.4401)
5 mm (0.19")
5 mm (0.19")
1 to 30 m (3 to 100')
1 to 30 m (3 to 100')
45 cm (18")
30 cm (12")
45 cm (18")
30 cm (12")
Overfill Safe
Materials Cable
Process Seal
Probe Outside Diameter
Process Connection
Threaded
Flanged
70 bar @ +20C (1000 psi @ +70 F) 431 bar @ +20 C (6250 psi @ +70 F)
Dielectric Range
1.7 to 100
1.7 to 100
Vacuum Service
Negative Pressure,
but no hermetic seal
Full Vacuum
10,000 (mPa.s)
10,000 (mPa.s)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Viscosity
Media Coating
14
FLEXIBLE
PROBES
FOR
LIQUIDS
MATRIX
CONTINUED
7y4 (Future)
7y6 (Future)
7y7
Description
Single Flexible
Standard Temperature
Single Flexible
HTHP
Twin Flexible
Standard Temperature
Application
Level
Level
Level/Interface
Installation
Chamber
Chamber
Tank/Chamber
Overfill Safe
No
No
No
316 (1.4401)
316 (1.4401)
5 mm (0.19")
5 mm (0.19")
(2) 6 mm (0.25")
1 to 30 m (3 to 100')
1 to 30 m (3 to 100')
1 to 30 m (3 to 100')
45 cm (18")
30 cm (12")
45 cm (18")
30 cm (12")
45 cm (18")
30 cm (12")
Materials Cable
Process Seal
Cable Outside Diameter
Process Connection
Threaded
Flanged
70 bar @ +20 C (1000 psi @ +70 F) 431 bar @ +20 C (6250 psi @ +70 F) 70 bar @ +20 C (1000 psi @ +70 F)
Dielectric Range
1.7 to 100
1.7 to 100
1.7 to 100
Vacuum Service
Negative Pressure,
but no hermetic seal
Full Vacuum
Negative Pressure,
but no hermetic seal
10,000 (mPa.s)
10,000 (mPa.s)
1500 (mPa.s)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Maximum Error 10 %
of coated length
( % Error is dependent on
dielectric and thickness)
Viscosity
Media Coating
15
FLEXIBLE
PROBES
FOR
SOLIDS
MATRIX
7y2
7y5
Description
Application
Level
Level
Installation
Tank
Tank
Overfill Safe
No
No
Materials Cable
316 (1.4401)
316 (1.4401)
5 mm (0.19")
(2) 6 mm (0.25")
Process Connection
2" NPT or 2" BSP
2" NPT or 2" BSP
Threaded
Flanged Various ANSI, EN1092, and proprietary flanges Various ANSI, EN1092, and proprietary flanges
1 to 30 m (3 to 100')
1 to 30 m (3 to 100')
45 cm (18")
30 cm (12")
45 cm (18")
30 cm (12"12")
Dielectric Range
4 to 100
1.9 to 100
Vacuum Service
10,000 (mPa.s)
10,000 (mPa.s)
Viscosity
Media Coating
Transition zones (areas with reduced accuracy) are dielectric dependent. It is recommended to set the 0-100 % measuring range outside of the transition zones.
1.2 minimum dielectric when end of probe analysis is enabled.
ECLIPSE probes containing o-rings can be used for vacuum (negative pressure) service, but only those probes with glass seal are hermetically sealed
(helium leak <10-8cc/sec @ 1 atmos.).
414
6000
(6000)
379
5500
(5500)
345
5000
(5000)
310
4500
(4500)
276
4000
(4000)
241
3500
(3500)
207
3000
(3000)-15
0
(0)
316/316L SST
Hastelloy C276
Monel 400
40
100
(100)
95
200
(200)
150
300
(300)
200
400
(400)
260
500
(500)
448
6500
(6500)
448
6500
(6500)
7yS steam probes are rated to 88 bar (1275 psi) up to +300 C (+575 F)
7y3, 7y6 HTHP flexible probes:
Pressure is limited by the chamber
7y2, 7y5 bulk solids probes: 3,45 bar (50 psi) to +65 C (+150 F)
High pressure probes with threaded fittings are rated as follows:
7yD, 7yN, 7yP and 7y3 probes with threaded fittings have 248 bar (3600 psi)
rating. 7yM probes with threaded fittings have 139 bar (2016 psi) rating.
16
316/316L SST
Hastelloy C276
Monel 400
414
6000
(6000)
379
5500
(5500)
345
5000
(5000)
310
4500
(4500)
276
4000
(4000)
241
3500
(3500)
207
3000
(3000)-15
0
(0)
Temperature C (F)
NOTES:
95
200
(200)
200
400
(400)
315
600
(600)
425
800
(800)
540
1000
(1000)
Temperature C (F)
82,7
(1200)0
7yF, 7yG,
7yG, 7yT,
7yF,
7yT,7y1,
7y1,7y4,
7y4,7y7
7y7
68,9
(1000)0
55,2
(800)0
41,4
(600)0
27,6
(400)0
13,8
(200)0
0
(0)0
-15
0
(0)
40
100
(100)
95
200
(200)
150
300
(300)
200
400
(400)
260
500
(500)
O-RING
(SEAL)
SELECTION
CHART
O-RING/SEAL SPECIFICATIONS
Code
O-Ring
Material
Max. Process
Temperature
Viton GFLT
200 C @ 16 bar
(400 F @ 230 psi)
-40 C
(-40 F)
EPDM
-50 C
(-60 F)
200 C @ 16 bar
(400 F @ 232 psi)
-40 C
(-40 F)
70 bar @ 20 C
(1000 psi
70 F)
-20 C
(-4 F)
NACE applications
Kalrez 4079
HSN
135 C @ 22 bar
(Highly Saturated (275 F @ 320 psi)
Nitrile)
Buna-N
135 C @ 22 bar
(275 F @ 320 psi)
-20 C
(-4 F)
Neoprene
150 C @ 20 bar
(300 F @ 290 psi)
-55 C
(-65 F)
70 bar @ 20 C
(1000 psi
70 F)
Acetaldehyde, ammonia +
lithium metal solution,
butyraldehyde, di-water,
freon, ethylene oxide,
liquors, isobutyraldehyde
Acids, Ketones,
chlorinated HCs,
Chemraz 505
200 C @ 14 bar
(400 F @ 200 psi)
-20 F
(-30 C)
70 bar @ 20 C
(1000 psi
70 F)
Polyurethane
95 C @ 29 bar
(200 F @ 420 psi)
-55 C
(-65 F)
70 bar @ 20 C
(1000 psi
70 F)
200 C @ 16 bar
(400 F @ 232 psi)
-20 C
(-4 F)
200 C @ 16 bar
(400 F @ 232 psi)
-40 C
(-40 F)
70 bar @ 20 C
(1000 psi
70 F)
-195 C
(-320 F)
431 bar @
20 C
(6250 psi
70 F)
Aegis PF128
Kalrez 6375
17
REPLACEMENT
OF
DISPLACER
TRANSMITTERS
Ease of replacement:
Proprietary and standard ANSI flanges are offered on all
ECLIPSE Model 706 probes so existing chamber/cages
can be used.
In order to match the proper ECLIPSE transmitter with the
proper external cage, consider the following:
Type of application:
Use the proper GWR probe for the application, see
pages 7 and 10 through 16.
Overfill proof:
For optimum performance, use an Overfill-safe probe
in all chamber applications.
Note: Overfill occurs when the level rises above
the maximum range of operation. Some
GWR probes may provide erroneous output
in this zone unless an optimal, impedancematched design is used.
Minimum Cage Size:
Coaxial or Caged Coaxial probes: 2" minimum
Enlarged Coaxial probes: 3" minimum
Twin Cable probes: 4" minimum
Before
Body connection
20 mA / 100 %
Measuring range:
min 30 cm (12")
max 570 cm (224")
Displacer
length
After
4 mA / 0 %
F
min 25 mm (1")
Type
Process Connection
MAGNETROL
EZ & PN Modulevel
Masoneilan
Series 1200
Fisher series
2300 & 2500
Eckardt
Tokyo Keiso
FST-3000
ANSI/EN flange
Proprietary flange
ANSI/EN flange
Proprietary flange
ANSI flange
ANSI/EN flange
ANSI/EN flange
ANSI/EN flange
18
Displacer Length
mm (inches)
356 (14)
356 (14)
406 (16)
356 (14)
356 (14)
356 (14)
H = 300 (11.8)
H = 500 (19.7)
Probe Length
mm (inches)
Displacer + 178 (7)
Displacer + 203 (8)
Displacer + 203 (8)
Displacer + 254 (10)
consult factory
consult factory
Displacer + 229 (9)
Displacer + 229 (9)
PROPRIETARY
mm
FLANGES
(INCHES)
184 (7.25)
229 (9)
143 (5.62)
191 (7.50)
121 (4.75)
45
45
22
(0.87)
45
11
(0.43)
22
(0.87)
32
(1.25)
133
(5.23)
29
(1.12)
86
(3.37)
6
(0.22)
MAGNETROL
149 (5.875)
32
(1.25)
102
(4)
5
(0.188)
6
(0.25)
CHAMBERS
A brief description of the MAGNETROL chamber offering follows. For more details, refer to
MAGNETROL Sales Bulletin BE57-140.
MAGNETROL has a long tradition in offering cost-effective chambers. The MAGNETROL external
chamber is a self-contained cage designed for use with our top mounting level transmitters or
switches. Quality construction and a wide selection of configurations make this cage an ideal means
of utilizing the power of Guided Wave Radar without mounting directly into the process vessel.
MAGNETROL chambers are available with a wide variety
of options, and can be manufactured to comply with various regulations such as:
Commercial Design
ASME B31.1 Design Code
ASME B31.3 Design Code
NACE Design Code
PED
Some Model 706 probes can be installed into chambers
as small as 2". When a new chamber is required, it can be
Measuring
Measuring
Range
Range
Measuring
Measuring
Range
Range
Measuring
Measuring
Range
Range
NPT drain
1"1"NPT
drain
NPT drain
1"1"NPT
drain
Sealed Chamber
PACTware
PC
SOFTWARE
20
AGENCY
APPROVALS
AGENCY
MODEL APPROVED
APPROVAL CATEGORY
APPROVAL CLASSES
FM
706-5XXX-1XX
Intrinsically Safe
706-5XXX-3XX
Explosion-proof
(with Intrinsically Safe probe)
Dust Ignition-proof
CSA
ATEX
IEC
706-5XXX-XXX
706-5XXX-1XX
Intrinsically Safe
706-5XXX-3XX
Explosion-proof
(with Intrinsically Safe probe)
Dust Ignition-proof
706-5XXX-XXX
Non-Incendive
Suitable for:
706-5XXX-AXX
Intrinsically Safe
706-5XXX-CXX
Non-sparking
706-5XXX-DXX
Dust Ex
706-5XXX-BXX
Flame Proof
706-5XXX-AXX
Intrinsically Safe
Ex ia IIC T4 Ga
706-5XXX-CXX
Non-sparking
706-5XXX-BXX
Flame Proof
21
MODEL
NUMBER
TRANSMITTER
Models available for quick shipment, usually within 4 weeks after factory receipt of a complete purchase order, through the Expedite Ship Plan (ESP).
4 | POWER
5
24 VDC, Two-Wire
5 | SIGNAL OUTPUT
1
6 | SAFETY OPTIONS
0
7 | ACCESSORIES/MOUNTING
0
8 | CLASSIFICATION
0
9 | HOUSING
1
10 | CONDUIT CONNECTION
22
M20
10
2" NPT
2" NPT with sunshade
DIMENSIONS
mm
(inches)
86
(3.38)
106
(4.18)
96
(3.77)
212
(8.34)
86
(3.38)
236
(9.30)
106
(4.18)
129
(5.09)
96
(3.77)
2 cable
entries
102
(4.03)
45
Integral Electronics
Eclipse Housing
(45 View)
2 cable
entries
60
(2.37)
45
76
(3.00)
51
(2.00)
89
(3.50)
838 or 3650
(33 or 144)
95
(3.75)
2 holes
10 (0.38)
105
(4.15)
ELECTRICAL
WIRING
Power
Power supply:
supply:
GP
GP //intrinsically
intrinsically safe
safe //explosion-proof:
explosion-proof:min
min11
11VDC
VDC
HART
modem
HART modem
0% 100%
Standard
Standard shielded
shielded twisted pair cable
twisted
cable but not needed
recommended
(recommended
but NAMUR
not needed
when wired as per
NE when
21
wired
as per
NAMUR
field
(for field
strengths
upNE
to 21
10 for
V/m)
strenghts up to 10 V/m).
Galvanic
GalvanicBarrier
Barrier::
max:
DC @
max:28,4
28.4VVDC
@ 94 mA for intrinsically safe units
units
max:
DC @
380 mAfor
forFFoundation
Fieldbus
units
OUNDATION fieldbus
max:17,5
17.5VVDC
@ 380mA
(not
(notneeded
neededfor
forGP,
GP,Dust
DustEx,
Ex,and
andexplosion-proof
explosion-proofmodels)
models).
250 minimum required for HART Communications
250 minimum required for HART Communications
Ex
Non Ex
23
MODEL
NUMBER
ENLARGED
COAXIAL
PROBE
Models available for quick shipment, usually within four weeks after factory
receipt of a complete purchase order, through the Expedite Ship Plan (ESP).
1 | TECHNOLOGY
7
2 | MEASUREMENT SYSTEM
A
English
Metric
3 | CONFIGURATION/STYLE (RIGID)
D
Enlarged Coaxial, High Temp/High Pressure: Overfill w/Glass Seal (+450 C/+850 F) Available only with 10th digit N or D
Enlarged Coaxial, High Pressure: Overfill w/Glass Seal (+200 C/+400 F) Available only with 10th digit N or D
Enlarged Coaxial, Overfill Standard O-Ring Seal (+200 C/+400 F) Not available with 10th digit N or D
2"
150# ANSI RF
5M
3"
44
2"
300# ANSI RF
5N
3"
45
2"
600# ANSI RF
63
4"
150# ANSI RF
4K
2"
64
4"
300# ANSI RF
53
3"
150# ANSI RF
65
4"
600# ANSI RF
54
3"
300# ANSI RF
66
4"
900# ANSI RF
55
3"
600# ANSI RF
67
4"
1500# ANSI RF
56
3"
900# ANSI RF
68
4"
2500# ANSI RF
57
3"
1500# ANSI RF
6K
4"
58
3"
2500# ANSI RF
6L
4"
5K
3"
6M
4"
5L
3"
6N
4"
EH
DN 80, PN 320
EN 1092-1 TYPE B2
EN Flanges
DA
DN 50, PN 16
EN 1092-1 TYPE A
DB
EJ
DN 80, PN 400
EN 1092-1 TYPE B2
DD
DN 50, PN 63
EN 1092-1 TYPE B2
FA
DN 100, PN 16
EN 1092-1 TYPE A
DE
DN 50, PN 100
EN 1092-1 TYPE B2
FB
DN 100, PN 25/40
EN 1092-1 TYPE A
EA
DN 80, PN 16
EN 1092-1 TYPE A
FD
DN 100, PN 63
EN 1092-1 TYPE B2
EB
DN 80, PN 25/40
EN 1092-1 TYPE A
FE
DN 100, PN 100
EN 1092-1 TYPE B2
ED
DN 80, PN 63
EN 1092-1 TYPE B2
FF
DN 100, PN 160
EN 1092-1 TYPE B2
EE
DN 80, PN 100
EN 1092-1 TYPE B2
FG
DN 100, PN 250
EN 1092-1 TYPE B2
EF
DN 80, PN 160
EN 1092-1 TYPE B2
FH
DN 100, PN 320
EN 1092-1 TYPE B2
EG
DN 80, PN 250
EN 1092-1 TYPE B2
FJ
DN 100, PN 400
EN 1092-1 TYPE B2
TU
UT
UU
7
1
24
10
11
12
13
14
15
MODEL
NUMBER
ENLARGED
COAXIAL
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
ASME B31.1
L
M
ASME B31.3
ASME B31.3 & NACE MR0175/MR0103
NACE MR0175/MR0103
7 | FLANGE OPTIONS Offset flanges are only available with small coaxial probes
0
None
R
S
T
9 | SPACER MATERIAL
1
2
3
4
5
D
N
None/Glass Ceramic Alloy (dual-seal design with annunciator fitting)Available only with 3rd digit D or P
None/Glass Ceramic Alloy Available only with 3rd digit D or P
13 14 15 | INSERTION LENGTH
cm (030 999)
inches (012 396)
XXX
7
1
10
11
12
13
14
15
25
MODEL
SMALL
NUMBER
COAXIAL
PROBE
Models available for quick shipment, usually within four weeks after factory
receipt of a complete purchase order, through the Expedite Ship Plan (ESP).
1 | TECHNOLOGY
7
2 | MEASUREMENT SYSTEM
A
C
English
Metric
3 | CONFIGURATION/STYLE (RIGID)
D
P
S
T
Small Coaxial, High Temp/High Pressure: Overfill w/Glass Seal (+450 C/+850 F) Only available with 10th digit N or D
Small Coaxial, High Pressure: Overfill w/Glass Seal (+200 C/+400 F) Only available with 10th digit N or D
Small Coaxial, Saturated Steam (+300 C/+575 F), Max. Length=610 cm (240) Only available with 10th digit N, 11th digit 2
Small Coaxial, Overfill Standard O-Ring Seal (+200 C/+400 F) Not available with 10th digit N or D
41
42
ANSI Flanges
23
24
25
2K
33
34
35
3K
37
3M
1"
1"
1"
1"
1 12"
1 12"
1 12"
1 12"
1 12"
1 12"
150# ANSI RF
38
300# ANSI RF
3N
600# ANSI RF
43
600# ANSI RTJ 4 4
150# ANSI RF
45
300# ANSI RF
47
600# ANSI RF
48
600# ANSI RTJ
4K
900/1500# ANSI RF 4 M
900/1500# ANSI RTJ 4 N
1 12"
1 12"
2"
2"
2"
2"
2"
2"
2"
2"
2500# ANSI RF
2500# ANSI RTJ
150# ANSI RF
300# ANSI RF
600# ANSI RF
900/1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900/1500# ANSI RTJ
2500# ANSI RTJ
53
54
55
56
57
58
5K
5L
5M
5N
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
63
64
65
66
67
68
6K
6L
6M
6N
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF
1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900# ANSI RTJ
1500# ANSI RTJ
2500# ANSI RTJ
4"
4"
4"
4"
4"
4"
4"
4"
4"
4"
150# ANSI RF
300# ANSI RF
600# ANSI RF
900# ANSI RF
1500# ANSI RF
2500# ANSI RF
600# ANSI RTJ
900# ANSI RTJ
1500# ANSI RTJ
2500# ANSI RTJ
EN Flanges
BB
BC
CB
CC
CF
CG
CH
CJ
DA
DB
DD
DE
DF
DG
DH
DJ
A
B2
A
B2
B2
B2
B2
B2
DN
DN
DN
DN
DN
DN
DN
DN
25,
25,
40,
40,
40,
40,
40,
40,
PN
PN
PN
PN
PN
PN
PN
PN
16/25/40 EN
63/100 EN
16/25/40 EN
63/100 EN
160
EN
250
EN
320
EN
400
EN
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
16
25/40
63
100
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
160
250
320
400
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
EA
EB
ED
EE
EF
EG
EH
E J
FA
FB
FD
FE
FF
FG
FH
FJ
A
A
B2
B2
B2
B2
B2
B2
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
80, PN 16
80, PN 25/40
80, PN 63
80, PN 100
80, PN 160
80, PN 250
80, PN 320
80, PN 400
100, PN 16
100, PN 25/40
100, PN 63
100, PN 100
100, PN 160
100, PN 250
100, PN 320
100, PN 400
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
A
A
B2
B2
B2
B2
B2
B2
A
A
B2
B2
B2
B2
B2
B2
600#
600#
600#
600#
7
1
26
10
11
12
13
14
15
MODEL
SMALL
NUMBER
COAXIAL
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
K
L
M
N
Industrial
ASME B31.1
ASME B31.3
ASME B31.3 & NACE MR0175/MR0103
NACE MR0175/MR0103
7 | FLANGE OPTIONS Offset flanges are only available with small coaxial probes
0
1
2
3
None
Offset (For use with AURORA) 4 Only available with 3rd digit P, S or T
Offset with 12" NPT Vent (For use with AURORA) 4 Only available with 3rd digit P, S or T
Offset with 34" NPT Vent (For use with AURORA) 4 Only available with 3rd digit P, S or T
316 SS/316L SS
Hastelloy C
Monel Not available with 3rd Digit S
316 SS/316L SS with Carbon Steel Flange
Hastelloy C with Carbon Steel Flange
Monel with Carbon Steel Flange Not available with 3rd Digit S
9 | SPACER MATERIAL
1
2
3
5
12 | SPECIAL OPTIONS
0
13 14 15 | INSERTION LENGTH
cm (030 610)
inches (012 240)
XXX
7
1
2
2
10
11
12
13
14
15
27
MODEL
CAGED
NUMBER
PROBE
1 | TECHNOLOGY
7
2 | MEASUREMENT SYSTEM
A
English
Metric
3 | CONFIGURATION/STYLE (RIGID)
G
Overfill Caged Rigid Probe for use in chambers +200 C (+400 F) (Only available with 2", 3", and 4" flanges)
Overfill Caged High Temp/High Pressure Probe with Glass Seal for use in chambers +450 C (+850 F)
(Only available with 2", 3", and 4" flanges)
Overfill Caged High Pressure Probe with Glass Seal for use in chambers +200 C (+400 F)
(Only available with 2", 3", and 4" flanges)
2"
150# ANSI RF
54
3"
300# ANSI RF
63
4"
150# ANSI RF
44
2"
300# ANSI RF
55
3"
600# ANSI RF
64
4"
300# ANSI RF
45
2"
600# ANSI RF
56
3"
900# ANSI RF
65
4"
600# ANSI RF
47
2"
900/1500# ANSI RF
57
3"
1500# ANSI RF
66
4"
900# ANSI RF
48
2"
2500# ANSI RF
58
3"
2500# ANSI RF
67
4"
1500# ANSI RF
4K
2"
5K
3"
68
4"
2500# ANSI RF
4M
2"
5L
3"
6K
4"
4N
2"
5M
3"
6L
4"
53
3"
150# ANSI RF
5N
3"
6M
4"
6N
4"
EN Flanges
DA
DN 50, PN 16
EN 1092-1 TYPE A
EF
DN 80, PN 160
EN 1092-1 TYPE B2
DB
DN 50, PN 25/40
EN 1092-1 TYPE A
EG
DN 80, PN 250
EN 1092-1 TYPE B2
DD
DN 50, PN 63
EN 1092-1 TYPE B2
EH
DN 80, PN 320
EN 1092-1 TYPE B2
DE
DN 50, PN 100
EN 1092-1 TYPE B2
E J
DN 80, PN 400
EN 1092-1 TYPE B2
DF
DN 50, PN 160
EN 1092-1 TYPE B2
FA
DN 100, PN 16
EN 1092-1 TYPE A
DG
DN 50, PN 250
EN 1092-1 TYPE B2
FB
DN 100, PN 25/40
EN 1092-1 TYPE A
DH
DN 50, PN 320
EN 1092-1 TYPE B2
FD
DN 100, PN 63
EN 1092-1 TYPE B2
DJ
DN 50, PN 400
EN 1092-1 TYPE B2
FE
DN 100, PN 100
EN 1092-1 TYPE B2
EA
DN 80, PN 16
EN 1092-1 TYPE A
FF
DN 100, PN 160
EN 1092-1 TYPE B2
EB
DN 80, PN 25/40
EN 1092-1 TYPE A
FG
DN 100, PN 250
EN 1092-1 TYPE B2
ED
DN 80, PN 63
EN 1092-1 TYPE B2
FH
DN 100, PN 320
EN 1092-1 TYPE B2
EE
DN 80, PN 100
EN 1092-1 TYPE B2
FJ
DN 100, PN 400
EN 1092-1 TYPE B2
TU
UT
UU
7
1
28
10
11
12
13
14
15
MODEL
CAGED
NUMBER
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
ASME B31.1
ASME B31.3
NACE MR0175/MR0103
7 | FLANGE OPTIONS
0
None
Offset (For use with AURORA)4 Only available with 3rd digit G and 4th digit 6
Offset with 12" NPT Vent (For use with AURORA)4 Only available with 3rd digit G and 4th digit 6
Offset with 34" NPT Vent (For use with AURORA)4 Only available with 3rd digit G and 4th digit 6
316 SS/316L SS
Hastelloy C
Monel
9 | SPACER MATERIAL
2
D
N
None
13 14 15 | INSERTION LENGTH
inches (012 288)
cm (030 732)
XXX
7
1
0
2
10
11
12
13
14
15
29
MODEL
SINGLE
NUMBER
ROD
RIGID
PROBE
1 | TECHNOLOGY
7
2 | MEASUREMENT SYSTEM
A
C
English
Metric
3 | CONFIGURATION/STYLE (RIGID)
F
M
N
42
ANSI Flanges
33
34
35
43
44
45
47
48
4K
4M
4N
53
54
55
56
57
58
5K
5L
5M
2"
3"
3"
3"
3"
3"
3"
3"
3"
3"
5N
63
64
65
66
67
68
6K
6L
6M
6N
3"
4"
4"
4"
4"
4"
4"
4"
4"
4"
4"
EN Flanges
CB
CC
CF
CG
DA
DB
DD
DE
DF
DG
DH
DJ
EA
EB
EN
EN
EN
EN
40,
40,
40,
40,
PN
PN
PN
PN
16/25/40
63/100
160
250
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
16
EN 1092-1 TYPE A
25/40 EN 1092-1 TYPE A
63
EN 1092-1 TYPE B2
100
EN 1092-1 TYPE B2
DN
DN
DN
DN
50,
50,
50,
50,
PN
PN
PN
PN
160
250
320
400
EN
EN
EN
EN
DN 80, PN 16
DN 80, PN 25/40
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
A
B2
B2
B2
DN
DN
DN
DN
TYPE
TYPE
TYPE
TYPE
B2
B2
B2
B2
EN 1092-1 TYPE A
EN 1092-1 TYPE A
ED
EE
EF
EG
EH
E J
FA
FB
FD
FE
FF
FG
FH
FJ
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
80, PN 63
80, PN 100
80, PN 160
80, PN 250
80, PN 320
80, PN 400
100, PN 16
100, PN 25/40
100, PN 63
100, PN 100
100, PN 160
100, PN 250
100, PN 320
100, PN 400
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
1092-1
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
TYPE
B2
B2
B2
B2
B2
B2
A
A
B2
B2
B2
B2
B2
B2
7
1
30
10
11
12
13
14
15
MODEL
SINGLE
NUMBER
ROD
RIGID
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
ASME B31.1
ASME B31.3
NACE MR0175/MR0103
7 | FLANGE OPTIONS
0
None
316 SS/316L SS
Hastelloy C
Monel
Faced Flange, PFA coated wetted surfaces Only available with Digit 3rd digit F
9 | SPACER MATERIAL
0
12 | SPECIAL OPTIONS
Non-Removable RodOnly available with PFA Coated
Probes(8th digit F or P)
Removable Rod Not available with PFA Coated
Probes(8th Digit F or P)
0
1
13 14 15 | INSERTION LENGTH
cm (030 732)
inches (012 288)
XXX
7
1
0
2
0
8
10
11
12
13
14
15
31
MODEL
SINGLE
NUMBER
FLEXIBLE
PROBE
1 | TECHNOLOGY
7
2 | MEASUREMENT SYSTEM
A
English
Metric
Single Cable Flexible HTHP for in-tank applications (+450 C/+850 F) (Future)
Single Cable Flexible standard for chamber applications (+200 C/+400 F) (Future)
Single Cable Flexible HTHP for chamber applications (+450 C/+850 F) (Future)
42
ANSI Flanges
43
2"
150# ANSI RF
44
2"
300# ANSI RF
45
2"
600# ANSI RF
53
3"
150# ANSI RF
54
3"
300# ANSI RF
55
3"
600# ANSI RF
63
4"
150# ANSI RF
64
4"
300# ANSI RF
65
4"
600# ANSI RF
EN Flanges
DA
DN 50, PN 16
EN 1092-1 TYPE A
DB
DN 50, PN 25/40
EN 1092-1 TYPE A
DD
DN 50, PN 63
EN 1092-1 TYPE B2
DE
DN 50, PN 100
EN 1092-1 TYPE B2
EA
DN 80, PN 16
EN 1092-1 TYPE A
EB
DN 80, PN 25/40
EN 1092-1 TYPE A
ED
DN 80, PN 63
EN 1092-1 TYPE B2
EE
DN 80, PN 100
EN 1092-1 TYPE B2
FA
DN 100, PN 16
EN 1092-1 TYPE A
FB
DN 100, PN 25/40
EN 1092-1 TYPE A
FD
DN 100, PN 63
EN 1092-1 TYPE B2
FE
DN 100, PN 100
EN 1092-1 TYPE B2
7
1
32
10
11
12
13
14
15
MODEL
SINGLE
NUMBER
FLEXIBLE
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
7 | FLANGE OPTIONS
0
None
316 SS/316L SS
9 | SPACER MATERIAL
0
None
Viton GFLT
Kalrez 4079
Kalrez 6375
12 | SPECIAL OPTIONS
Non-removable Probe Cable
(for use with 3rd digit '2' only)
Removable Single-piece Probe Cable
(for use with 3rd digit '1' only)
0
1
13 14 15 | INSERTION LENGTH
meters (001 030)
feet (003 100)
XXX
7
1
0
8
3
10
11
12
13
14
15
33
MODEL
TWIN
NUMBER
FLEXIBLE
PROBE
1 | TECHNOLOGY
7
2 | MEASUREMENT SYSTEM
A
English
Metric
42
ANSI Flanges
53
3"
54
3"
55
3"
63
4"
64
4"
65
4"
EN Flanges
EA
DN 80, PN 16
EN 1092-1 TYPE A
EB
DN 80, PN 25/40
EN 1092-1 TYPE A
ED
DN 80, PN 63
EN 1092-1 TYPE B2
EE
DN 80, PN 100
EN 1092-1 TYPE B2
FA
DN 100, PN 16
EN 1092-1 TYPE A
FB
DN 100, PN 25/40
EN 1092-1 TYPE A
FD
DN 100, PN 63
EN 1092-1 TYPE B2
FE
DN 100, PN 100
EN 1092-1 TYPE B2
Confirm mounting conditions/nozzle diameter to ensure sufficient clearance.
7
1
34
10
11
12
13
14
15
MODEL
TWIN
NUMBER
FLEXIBLE
CONTINUED
PROBE
6 | CONSTRUCTION CODES
0
Industrial
7 | FLANGE OPTIONS
0
None
316 SS/316L SS
9 | SPACER MATERIAL
0
None
Viton GFLT
12 | SPECIAL OPTIONS
0
None
13 14 15 | INSERTION LENGTH
meters (001 030)
feet (003 100)
XXX
7
1
0
8
10
11
12
13
14
15
35
SEGMENTED
PROBE
12th
MODEL
DIGIT
OF
OPTIONS
NUMBER
Probe Model
One Segment
Two Segments
Three Segments
Four Segments
Coaxial Models
7yD, 7yP and 7yT
(Enlarged versions only)
(3", DN 80 Process
Connections and larger)
60 305 cm
(24 120")
120 610 cm
(48 240")
180 914 cm
(72 360")
240 990 cm
(96 396")
Caged Models
7yG, 7yL and 7yJ
30 305 cm
(12 120")
60 610 cm
(24 240")
90 732 cm
(36 288")
120 732 cm
(48 288")
NOTE: Segments will be evenly divided over the length of the probe.
36
COAXIAL
mm
PROBE
DIMENSIONS
(INCHES)
86
(3.38)
86
(3.38)
106
(4.18)
96
(3.77)
86
(3.38)
106
(4.18)
96
(3.77)
96
(3.77)
236
(9.30)
45
2 cable
entries
106
(4.18)
236
(9.30)
236
(9.30)
45
2 cable
entries
45
2 cable
entries
113
(4.46)
197
(7.76)
Mounting
flange
265
(10.45)
Mounting
flange
Probe
insertion
length
Probe
insertion
length
Model 7yT
with flanged connection
86
(3.38)
Model 7yP
with flanged connection
Probe
insertion
length
Model 7yD
with flanged connection
106
(4.18)
96
(3.77)
C
A
E
236
(9.30)
2 cable
entries
45
mm (inches)
293
(11.55)
Mounting
flange
Probe
insertion
length
Dim.
Small Diameter
Enlarged (standard)
22,5 (0.88)
45 (1.75) - SST
49 (1.92) - HC and Monel
B
C
D
E
8 (0.31)
100 (4.08)
4 (0.15)
96 (3.78)
16 (0.63)
153 (6.05)
8 (0.30)
138 (5.45)
Model 7yS
with flanged connection
37
CAGED
mm
PROBE
DIMENSIONS
(INCHES)
86
(3.38)
86
(3.38)
106
(4.18)
86
(3.38)
96
(3.77)
106
(4.18)
106
(4.18)
96
(3.77)
96
(3.77)
236
(9.30)
236
(9.30)
236
(9.30)
45
2 cable
entries
45
2 cable
entries
45
2 cable
entries
119
(4.70)
Mounting
flange
D
Mounting
flange
Probe
insertion
length
D
Probe
insertion
length
L
L
Model 7yG
with flanged connection
38
265
(10.45)
162
(6.39)
Mounting
flange
Model 7yL
with flanged connection
Probe
insertion
length
D
L
Model 7yJ
with flanged connection
Cage Size
2"
13 to 19 mm (0.5 to 0.75")
46 mm (1.82")
3"
19 to 29 mm (0.75 to 1.13")
67 mm (2.64")
4"
27 to 38 mm (1.05 to 1.50")
91 mm (3.60")
SINGLE
mm
ROD
RIGID
PROBE
DIMENSIONS
(INCHES)
86
(3.38)
86
(3.38)
86
(3.38)
106
(4.18)
106
(4.18)
106
(4.18)
96
(3.77)
96
(3.77)
96
(3.77)
236
(9.30)
236
(9.30)
236
(9.30)
45
2 cable
entries
45
2 cable
entries
45
2 cable
entries
115
(4.53)
Mounting
flange
265
(10.45)
213
(8.38)
Mounting
flange
Mounting
flange
Probe
insertion
length
9,6
(0.38)
Model 7yF
with flanged connection
9,6
(0.38)
Probe
insertion
length
Model 7yM
with flanged connection
13
(0.50)
34
(1.33)
Probe
insertion
length
Model 7yN
with flanged connection
39
SINGLE
mm
FLEXIBLE
PROBE
(INCHES)
86
(3.38)
DIMENSIONS
86
(3.38)
106
(4.18)
86
(3.38)
106
(4.18)
106
(4.18)
96
(3.77)
96
(3.77)
96
(3.77)
236
(9.30)
236
(9.30)
236
(9.30)
45
2 cable
entries
45
2 cable
entries
45
2 cable
entries
115
(4.53)
Mounting
flange
265
(10.45)
265
(10.45)
Mounting
flange
Mounting
flange
Probe
insertion
length
51 (2)
51 (2)
51 (2)
0,5 (0.19)
99
(3.88)
19 (0.75)
Model 7y3
with flanged
connection
Model 7y1
with flanged connection
Model 7y6
with flanged
connection
152
(6)
86
(3.38)
86
(3.38)
Probe
insertion
length
Probe
insertion
length
152
(6)
106
(4.18)
106
(4.18)
96
(3.77)
96
(3.77)
236
(9.30)
236
(9.30)
45
2 cable
entries
2 cable
entries
51 (2)
119
(4.70)
Mounting
flange
139
(5.46)
Mounting
flange
51 (2)
51 (2)
Probe
insertion
length
Probe
insertion
length
Model 7y4
with flanged
connection
40
152
(6)
45
152
(6)
Model 7y2
with flanged
connection
152
(6)
IN
TANK
MOUNTING
STANDARD
SINGLE
ROD
PROBE
CONSIDERATIONS
2, 4 and 6
1. Turbulence
objects in the proximity of the probe can cause erroneous readings. Please refer to the table below for
guidelines, but please contact the factory with any
questions as the distances shown can be reduced with
the use of PACTware.
Distance to probe
Acceptable objects
Correct Installation
Pipe reducers
should not be used
TWIN
mm
FLEXIBLE
PROBE
(INCHES)
DIMENSIONS
86
(3.38)
106
(4.18)
86
(3.38)
106
(4.18)
96
(3.77)
236
(9.30)
96
(3.77)
152
(6)
236
(9.30)
51 (2)
2 cable
entries
45
2 cable
entries
45
135
(5.31)
115
(4.54)
Mounting
flange
Mounting
flange
Probe
insertion
length
Probe
insertion
length
22,2 (0.875)
13 (0.50) Rods
6,3 (0.248)
Model 7y5
with flanged connection
Model 7y7
with flanged connection
IN
TANK
MOUNTING
TWIN
FLEXIBLE
CONSIDERATIONS
42
PROBE
AURORA
CHAMBER
two independent technologies provides excellent redundancy. A custom float positioned within the AURORA
chamber travels up and down following level changes.
The float contains an internal group of magnets that are
coupled with magnets in the flags of the visual indicator mounted on the outside of the chamber. As the float
moves, the flags rotate to expose the color of their opposite side. The position where the flags color changes corresponds to a point on the measuring scale indicating true
level. In addition to this external visual indicator operated by the AURORA internal float, the ECLIPSE Model 706
transmitter reflects electromagnetic radar pulses directly
off the liquid surface providing a real-time continuous
level output.
Visual
Visual
Indication
Indication
Range
Range
Center
Center
to
to
Center
Center
Visual
Visual
Indication
Indication
Range
Range
Center
Center
to
Center
Center
Visual
Visual
Indication
Indication
Range
Range
Center
Center
to
to
Center
Center
43
ESP
Expedite
Ship
Plan
dimensions apply).
PRODUCT WARRANTY
:2008
ALL MAGNETROL ELECTRONIC AND ULTRASONIC LEVEL CONTROLS ARE WARRANTED FREE OF DEFECTS IN MATERIALS AND WORKMANSHIP FOR ONE FULL YEAR FROM THE DATE OF ORIGINAL FACTORY SHIPMENT. IF RETURNED WITHIN THE WARRANTY PERIOD; AND, UPON FACTORY INSPECTION
OF THE CONTROL, THE CAUSE OF THE CLAIM IS DETERMINED TO BE COVERED UNDER THE WARRANTY; THEN, MAGNETROL INTERNATIONAL WILL REPAIR OR REPLACE THE CONTROL AT NO COST TO THE PURCHASER (OR OWNER) OTHER THAN TRANSPORTATION.
MAGNETROL SHALL NOT BE LIABLE FOR MISAPPLICATION, LABOR CLAIMS, DIRECT OR CONSEQUENTIAL DAMAGE OR EXPENSE ARISING FROM THE INSTALLATION OR
USE OF THE EQUIPMENT. THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED, EXCEPT, SPECIAL WRITTEN WARRANTIES COVERING SOME MAGNETROL
PRODUCTS.
BULLETIN N:
EFFECTIVE:
SUPERSEDES:
DEUTSCHLAND
INDIA
ITALIA
RUSSIA
U.A.E.
UNITED
KINGDOM
Unit 1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL
Tel. +44 (0)1444 871313 Fax +44 (0)1444 871317 E-Mail: sales@magnetrol.co.uk
www.magnetrol.com
BENELUX
FRANCE
BE 57-106.3
MAY 2014
JULY 2013