Professional Documents
Culture Documents
SLR-UM
56
Seat
No.
ilililt
il1il
lilltll llllllll
lllllill
lll lllll
Centre
Seat No.
Code No.
Seat No. in words
ll) Examination,2014
27'5'2014
Time
II
Language of Answer
Examination
Paper No.
Subject
Out of
Marks -
Signature of
Examination
(Paper
Code No.
Examiner
lnstructions:
P.T.O.
ilfl
IilI
-68*
*s*$u**
/\\
h-\LJ-
Q*'"
MCQ/Objective Type euestion paper
Duration :30 Minutes
1. Write the correct option
in the box given
I:
1) ln case of 2-way slab, the limiting
defrection of srab
a) Primarily a function of long span
Marks:20
is
n
I
span
is greater
than 1/12 0t crear span or 600
mm whichever is ress for end
span
with one end free and other
continuous shall
t
t
a) crear span +
be--
d/2
b) Clear span + d
c)
c)
b) Short spans
spans
d) None of these
?-
ililril
il]t
5)
SLR.UM
-3-
times width.
a)
b) 3t4
1lB
c) 114
d)
112
section is
a) Above N.A.
c)
b) Below N.A.
below
d) Entire section
7) For two way slab for max. B.M. per unit width in a slab in longer
direction is
a) crrWl*2
c) u*wlf
b) crrw(
d) cr*Wlfr
9)
c)
Both of above
a) 2 Md +Mll2p
b) Md + 2Mll2p
c) 2 Md +2Mllp
d) Noneoftheabove
a) 0.3
b) 0.4
c)
d) 0.6
0.5
a)
c)
d)
fck
- 56
SLR-UM
- 56
rilIililillll lllllIllllllllllllllllllllllll
a) 9 kN-m
b) 9 kNm/m
c)
d) 13.2 kNm/m
13.2 kNm
is
a) Axial stress
b) Bending stress
14) From limiting deflection point of view, use of high strength steel
in RC beam results in
a) Reduction
c)
in dePth
lncrease in dePth
b) No change in depth
d) lncrease in width
b) Relaxation
c)
of steelcan be ignored
,:l
- 56
SLR-UM
-5-
Seat
No.
II
Marks :80
lnstructions
ll. Design an open well type stair for a college building using the following data
floor levels.
Thickness of wall = 300 m
Use M20 concrete and Fe-500
v-
steel.
13
ilt. Design a reinforced concrete slab for a room of clear dimension 3.65 m x 5.0 m.
The slab is supported all around on walls of width 300 mm. The slab has to carry
a live load of 4 kN/m2 and floor finish 1 kN/m2. Use M20 concrete and Fe-500
steel. Assume corners are held down. Sketch the details of
reinforcement.
13
lv. Design the stem slab of a counterfort retaining wall, if the height of wall above
the ground level is 5 m. SBC of soil is 200 kN/m2, angle of internal friction is 30'
steel.
14
SLR.UM
V.
56
ililil1
ililililililililililil ililililililt
Design a three span continuous rectangular beam of span 6.50 m each to catry a
dead load of 15 kN/m and live load of 9.5 kN/m. The beam is supported by
columns. Use M20 mix and Fe 500 grade of steel. Sketch the reinforcement
details.
13
SECTION _
II
Vl. A P.S.C. rectangular beam 400 mm x 600 mm carries a UDL of 35 kN/m with
span 6 m. The beam is applied with a prestressing force of 1000 kN along a
:-
tendon having parabolic profile with eccentricity 100 mm at center and zero at
supports. Calculate the extreme stresses for the mid span section by using
strength concept, stress concept and load balancing
concept.
13
Vll. A PSC beam 230 mm wide and 450 mm deep has a span of 10 m. The beam is
prestressed by steel wires of area 350 mm2 provided at a uniform eccentricity of
75 mm with an initial prestress of 1250 N/mm2. Determine the percentage loss of
tr
ts-a-ox1O5N/mm2
tr
- e.5 x 105 N/mm2
-c-o
. Relaxation
-_
13
:
14
rf
ll
ll
SLR.UM
lX. Figure 1 shows a PSC beam 400 mm wide and 800 mm deep. Determine the
horizontal, vertical and shear stresses at the point Q in the end block. Find also
the principal stresses at Q. The tendons are placed at an eccentricity of 100 mm.
The anchor plate is 300 mm wide and 200 mm deep. Prestressing force in
!$$mm
trI
tt0*nr
,L
I
,
?!0$n1
t
I
P{6arm
J-
-.{-600rnrr
(;)
Kq
- 0.251,Kr=-2.47.
56