You are on page 1of 5

INSTITUTE OF AERONAUTICS & ENGG.

PAPER II
SET 7A
Q1.

Q17.

The sensitivity of voltmeter is expressed in


1. Ohm
2. Watt
3. Emf
4. Ampere 1(ohm/voly)
In inspection of bolt holes for pits and cracks is carried out
1. Before starting reaming
2. After finishing reaming
3. Before and after starting reaming
4. Done
In coolers or radiators where operating temperature is high soldering is not done but
1. Soldering can be done with approved flux
2. Inert gas welding
3. Seam welding
4. Spot welding
The function of flux in brazing operation is to
1. Minimize oxidation
2. To break the surface tension of filling material
3. To flow filler material all round
Cracks in thick material welding can be checked by
1. Eddy current
2. Dye penetrant
3. Ultrasound
Heat treatment of N-alloy is carried out by
1. Solution heat treatment
2. Solution and precipitation HT
3. Age hardening
4. All
To charge the fire in case of only one tire, the jack should be used
1. To just clear the tire from ground
2. Hydraulic jack (single base jack)
3. Chockes used with remaining wheel
4. All are correct
Mark the correct statement
1. The diametrical pitch and pitch diameter in a spur gear are same
2. If the dia. Pitch (DP) is given you can find out the addendum
3. If we divide DP by PD we can get size of teeth
4. If the DP is given you can find out the addendum
Kevalor is
1. While gliming cloth
2. 4-times more tensile strength than AL
3. It is used for primary structure
4. All of the above
A charge is moving along magnetic lines of force
1. If force will always act
2. No force will act
3. May act or may not act
4. None
With prepregs
1. Manual application no required
2. Has to be kept in freezer
3. Both 1 & 2
4. None
Weld decay can be prevent by
1. Presence of titanium and nycheum
2. Quick heating
3. Both 1 & 2
4. Low temperature
The size of the cold chisel is determined by
1. Length of cutting edge
2. Weight
3. Width of cutting edge
4. None
The term associated with warm gear is
1. Thread
2. Thread radius
3. Pitch
4. Both 1 & 2
Temperature of work in a furnace can be measured by
1. Thermistor
2. Pyrometer
3. Color of work
4. Thermocouple
The given drawing indicates
1. Cutting plane
2. Sectional view
3. Viewing plane
4. Cutting plane for complex view
The given figure indicates
2. Brass
4. None of these

Q18.

1. Cork, felt, fabric


3. Magnesium
The given figure indicates
1. Solenoid and thread batteries
3. Solenoid and one battery having three cell

2. Transformer and three batteries


4. All are correct

Q2.
Q3.
Q4.
Q5.
Q6.
Q7.
Q8.

Q9.
Q10.
Q11.
Q12.
Q13.
Q14.
Q15.
Q16.

Q19.
Q20.
Q21.

Q22.
Q23.

Q24.
Q25.

Q26.
Q27.
Q28.
Q29.
Q30.
Q31.
Q32.
Q33.
Q34.
Q35.
Q36.

Q37.
Q38.

For reaming holes should be under size


1. About 0.003 to 0.007
2. About 0.007 to 0.010
3. Not necessary
4. None of the above
Convert 29 into binary system
1. 111102
2. 101112
3. 110112
4. None of these
The radiographic inspection
1. Low wave length signal travel with velocity of light
2. High wave length signal travel with velocity of light
3. Both 1 & 2
In ATA 100 systems marking on the cable as per
1. Prefix and strefix
2. Prefix and suffix
3. Number and letter
4. 1 & 3 are correct
The given figure indicates
1. Universal head
2. Brazier head
3. Round head
4. Any one of the above
In an alto meter if there is absence of barometer is pressure the pitot line is checked by
1. Vacuum chamber
2. Micro meter
3.
4.
The given figure indicates
1. Shake proof washer
2. Internal star washer
3. Both 1 & 2
4. None of these
In pitot static system the static vent to of the flat plate tube any where in the a/c structure to prevent
1. Position error
2. Instrument error
3. Protection against ice formation
4. Both 1 & 3 are correct
The purpose of annealing is to
1. Soften the metal
2. Relive internal stresses
3. Both 1 & 2 are correct
4. None of these
The given tool is used for
1. Counter sinking
2. Counter boring
3. Drilling
4. Any one of the above
Aviation ship is used for cutting
1. Heat treated Al-alloy and stainless steel
2. Cu and its alloy
3. Any soft metal
4. All the above
The micrometer reading is showing
1. Positive zero error
2. Negative zero error
3. No error
4. None of these
The given reading shown
1. Positive zero error
2. Negative zero error
3. No error
4. None of these
In silver soldering the temperature ranges between
1. 200 deg. C 400 deg. C
2. 400 deg. C 600 deg. C
3. 505 deg. C 805 deg. C
4. 800 deg. C 1000 deg. C
The A.S.I. instrument consists of
1. One capsule
2. Two set of capsules
3. Three set of aneroid capsules
4. There is no aneroid used of A.S.I
The given figure in computer indicates
1. Entry-ON, exit-OFF
2. Entry- OFF, exit ON
3. Data is not available
4. All are wrong
Hydrogen gas emits in the battery during servicing
1. During the process of charging
2. Is Ni-cd battery when charging is completed
3. When battery is over charged
4. When connection on their terminal is versed
The given fault (as per figure) found in spot welding is
1. Porosity crack
2. Slashing
3. Deforming of weld
4. None of these
A screw having no head flush with the structure can be turned by
1. Allean key
2. Screw extractor
3. Simple crew driver
4. Both 1 if have hex grove head and 2
As per figure it is
1. Sector gear
2. As in 1 and when used with external gear- it gives the intermittent rotary motion
3. Spur gear having few teeth broken
4. Both 1 & 2 are correct

Q39.

Q40.
Q41.
Q42.
Q43.
Q44.

Q45.
Q46.
Q47.
Q48.
Q49.
Q50.

Q51.

Q52.
Q53.
Q54.
Q55.
Q56.
Q57.
Q58.
Q59.

In oxyacetylene welding to extinguish the flame it is good practice to


1. First close oxygen and then acetylene regulator
2. First close acetylene and then oxygen regulator
3. Close oxygen and acetylene regulators at a time
4. None of these
For welding cracks which type of joints should be preferred
1. Butt joining
2. Lap joining
3. Edge joining
4. None of these
In brazing which type of flame is used
1. Carburizing
2. Neutral
3. Oxidizing
4. Any one can be used
The given tool is used for making spot facing to seal the washer nut bolt head is
1. Counter sink
2. Counter bore
3. Reamer
4. Any one of them
The extended round portion which is indicated by letter A in the above figure is known as
1. Pilot straightner
2. Straighter
3. Guide
4. All the above are wrong
For making neat and clean welding
1. After welding remove the excess metal with file
2. The filler material should be properly filled and evenly spaced
3. Fill the gap with Cu of brass
4. All are wrong
The thermo-plastic material can be
1. Harden after cooling and soften after heating 2. Harden after cooling but can not be soften after heating
3. Used for making wind shield
4. Both 1 & 3 are correct
Mg-alloy has no more used in a/c because
1. Suspectable to corrosion
2. Chances of cracking
3. Highly resistance to corrosion
4. Both 1 & 2 are correct
Rockwell hardness test is carried on specimen to
1. Measure depth
2. Measure resistance to penetration
3. Both 1 & 2 are correct
4. Measure the diameter of impression
In oxyacetylene, the amount of oxygen and acetylene gases are in equal proportion as indicated in figure is the
1. Neutral flame
2. Oxidizing flame
3. Reducing flame
4. No flame will be- produced in this manner
Y & W indicates
1. Annealed
2. Solution heat treatment and quenched but not aged
3. Solution heat treatment & cold work
4. Stabilized
Triode valve consists of
1. Heater, cathode, plate and meshing wire screen (grid) between plate cathode
2. Heater, cathode and plate
3. Heater, cathode, control grid, screen, grid and plate
2. Heater, cathode, control grid, screen suppressor grid and plate
For converting galvanometer into voltmeter connect
1. High resistance wire in series with meter for increase range
2. Low resistance wire in series with meter
3. High resistance wire in parallel with meter
4. Low resistance wire in parallel with meter
Inductance depends on
1. No. of turns of the coil
2. Core material of the coil
3. Cross-section area
4. All the above are correct
Transformer is an electrical device with is used
1. For carrying high voltage to ling distance
2. In radio set
3. Both 1 & 2 are correct
4. None of these
In silicon control rectifier, there is
1. Three junction
2. Two terminals are forward based and two are reversed based
3. Four junction
4. None of these
This figure indicates
1. Delta connection alternator
2. Three phase alternator
3. Wire connection alternator
4. Both 1 & 2 are correct
The given figure indicating
1. Porosity
2. Pitting
3. Tight crack
4. Partially welded lap or tight crack
The drill size dia can be classified satisfactory
1. 1 to 80
2. A to Z
3. Both 1 and 2 are correct
4. None of the above
Red brass is used
1. For fuel and oil line fittings
2. As in 1 and also called bronze
3. As in 2 and has poor casting and forming quality
4. None
Nickel in steel increases

Q60.

Q61.

Q62.
Q63.
Q64.

Q65.
Q66.
Q67.
Q68.

Q69.
Q70.
Q71.
Q72.
Q73.

Q74.

Q75.
Q76.
Q77.

Q78.

1. Hardness
2. Yield strength
3. Elastic limit
4. All of the above
Geiger counter is used to
1. Measure the radioactive contamination of a/c flying above stratosphere
2. Check the condition of a/c after heavy landing
3. Check the penetration of a/c by ultraviolet rays above stratosphere
4. None of the above
Stalling angle critical angle of attack is the
1. Maximum life angle
2. Minimum lift angle
3. As in 1 and at which separation of airflow takes from upper surface of wing
4. As in 2 and at which separation of airflow takes from lower surface of wing
Angle of ACME thread is
1. 45o
2. 38o
o
3. 12
4. 29o
The type of compressor used in air cycle cooling machine is
1. Axial compressor
2. Inward flow compressor
3. Outward flow compressor
4. None
Mark the correct statement
1. Al-alloy bolts of dia less than mm are not used in primary structure
2. All Al-alloy nuts and bolts are used where frequent removal is required
3. Both 1 & 2 are correct
4. None of the above
Mark the correct statement
1. Lap joint is best for oxy-acetylene welding
2. Single lap joint is resistance to shearing
3. Single lap joint is resistance to bending
4. All of the above are wrong
Aircraft structural CRS is welded by
1. Butt welding
2. Spot welding and sea welding
3. Butt and spot welding
4. Spot welding
Precision wire wound resistors are wound with
1. Carbon
2. Copper
3. Maganin
4. All of the above
Corrosion of titanium and its alloys are
1. Difficult to detect
2. Easy to detect
3. As in 1 and increase with high temperature and salt
4. As in 2 and removed with Al-grid or Al-polished
If acid is spilled over skin from an a/c battery then it cleaned with
1. Water
2. Water and boric acid
3. Water and bicarbonate of soda
4. All
Ni-cad battery is rapidly charged with
1. Constant current and variable voltage
2. Constant voltage and variable current
3. Variable voltage and variable current
4. Both 1 & 2
Indication of corrosion on
1. Al and Mg as etching and pitting
2. Copper as greenish film
3. Steel as white marks
4. Both 1 & 2
Which non ferrous metal can be case hardened
1. Ni
2. Ti
3. Cu
4. Al
Jo-bolt is
1. Externally threaded two piece rivet
2. Externally threaded three piece rivet
3. Internally threaded three piece rivet
4. Can replace general bolts in compression to their strength
Jum buckle is
1. For minor adjustment in cable length and cable tension
2. Has matching left and right hand threads
3. Has internally threaded ends and externally threaded end terminals
4. All of the above
Extrusion is used for making
1. Channels
2. Angle
3. T-section
4. All
Generator frequency depends on
1. No. of poles
2. RPM
3. Both 1 & 2
4. None
For a battery to have high ampere hour capacity and high terminals voltage
1. Low internal resistance
2. High internal resistance
3. Does not depend on internal resistance 4. None
Plug gage is used for

Q79.
Q80.

1. Checking the internal dia of cylindrical shaft


2. Checking the size of plug needed for blanking
3. Checking the accuracy of holes
4. All of the above
A bolt should be installed
1. Upward and downward
2. Upward and downward
3. Downward and forward
4. Downward and rearward
In a PN function diode, holes move from P-region to N- region because of
1. Diffusion
2. Pressure difference
3. Higher concentration of holes in P- region
4. Electrons in N- region attracts holes form P-region

You might also like