Professional Documents
Culture Documents
Q. 1
Q. 2
Q. 3
Q. 4
Q. 5
Q. 6
Q. 7
Q. 8
Q. 9
Q. 10
Q. 11
Q. 12
Q. 13
Q. 14
Q. 15
Q. 16
Q. 17
Q. 18
Q. 19
Q. 20
Q. 60 In a reverse current cut out relay there are two winding on the core
(a) A series winding connected across the generator and a shunt winding connected in series
with main supply
(b) A series winding in series with the main supply and shunt winding across the generator*
(c) Both winding connected in series
(d) Both winding connected across the generator
Q. 61 In a relay(a) Operating element consists of solenoid and armature
(b) Operating element consists of one or more pairs of contacts
(c) Controlling element consists of one or more pairs of contacts
(d) Both (a) & (c)*
Q. 62 Switches used for range selection of a single voltmeter to read the voltage several bus bar
(a) gang switches
(b) rotary switches*
(c) toggle switches
(d) none
Q. 63 A typical "push-in-solenoid switches" used in a turbo prop engine starting circuits are
operated
(a) unusually
(b) electro magnetically
(c) both (a) and (b)*
(d) either (a) or (b)
Q. 64 Push switches are designed as independent units for
(a) push to make operation
(b) push to break operation
(c) either (a) or (b)
(d) both (a) and (b)*
Q. 65 Several dependent circuit in the category of general purpose are operated by
(a) limit switches
(b) gang switches*
(c) relay switches
(d) thermal switches
Q. 66 Switches used for general purpose switching functions are
(a) limit switches
(b) Toggle switches*
(c) micro switches
(d) relay switches
Q. 67 Tune s/w is designed to actuate relays which in turn control
(a) the supply of dc to heating elements of de - icing
(b) the supply of ac to heating elements of de icing*
(c) either (a) or (b)
(d) both (a) and (b)
Q. 68 Fuses are to(a) Protect the wiring
(b) Protect the equipment
(c) Protect the supply source
(d) All of the above*
Q. 69 Relay is installed in electrical circuit(a) Near the source of supply
(b) Near the component*
(c) Any place in the circuit
(d) Either (a) or (b) is correct
Q. 70 The rapidity of 'make' or 'brake' of mercury switches dependents upon
(a) temperature of the mercury
(b) surface tension of mercury*
(c) difference in temperature of the mercury
(d) none
Q. 71 Thermal S/W is use to(a) Trip the circuit above preset of temperature*
(b) Below preset, temperature
(c) At preset temperature
(d) None of the above
Q. 72 In electrical circuit, circuit breakers are placed(a) Near the component
(b) Any where in the circuit
(c) Near the source of power supply*
(d) None
Q. 73 Thermal switch are connected in
(a) Series and trips on over heating *
(b) Connected in parallel
(c) Connected in series parallel
(d) Any of the above way
Q. 74 Micro switch contact move
(a) Maximum upto 1/16 inch*
(b) More than 1/16 inch
(c) Less than of inch
(d) None of the above
Q. 75 Unit of resistivity is
(a) Ohms / meter
(b) Ohms meter*
(c) Ohms
(d) mho
Q. 76 Unit of conductance is
(a) Ohms
(b) Mho*
(d) Rel
(d) Rilbert
Q. 77 A Unique features of a wire wound resistor is its
(a) Low power rating
(b) Low cost
(c) High stability*
(d) Small size
Q.
Q.
Q.
Q.
Q.
(a) 20
(b) 5 *
(c) 2.5
(d) 40
96 The r.m.s valve of A. C. is equal to its value at angle of
(a) 60 degree
(b) 45 degree *
(c) 30 degree
(d) 90 degree
97 In a series R-L circuit(a) VL leads VR by 900
(b) IL lags VR *
(c) VL lags VR by 450
(d) VL leads VR by 450
98 The power factor of an R-C circuit is
(a) zero
(b) between 0 and 1*
(c) unity
(d) none of above
99 Resonance curve of resonance circuit is a plot of frequency versus.
(a) voltage
(b) impedence
(c) current*
(d) none
100 As a Q factor of a circuit _______________ its selectivity becomes _________
(a) Increases, better*
(b) Increases, worse
(c) Decreases, better
(d) Decreases, narrower