Professional Documents
Culture Documents
Materials are usually classified into two main groups. The most convenient way to
Study the properties and uses of engineering materials is to classify them
Into families as shown in figure below:
1. Metals
1.1 Ferrous metals
These are metals and alloys containing a high proportion of the element iron.
They are the strongest materials available and are used for applications where high
strength is required at relatively low cost and where weight is not of primary importance.
In general metals have high thermal conductivity, a high density, ductility, a relative
The ferrous metals themselves can also be classified into "families', and these are shown
in figure below:
materials.
They are mainly used with other metals to improve their strength.
Some widely used non-ferrous metals and alloys are classified as shown in figure:
These are non metallic materials that do not exist in nature, although they are
manufactured from natural substances such as oil, coal and clay. Some typical examples
are classified as shown in figure 6.
They combine good corrosion resistance with ease of manufacture by molding to shape
Plastics: A plastics consists of polymers plus various additives such as dye, fillers,
retardants, etc. Polymers have low electrical conductivity hence they are used for
electrical and thermal insulation. Compared with metals they have low densities, expand
more when there is change in temperature, and are generally more corrosion resistant,
have a lower stiffness, stretch more and are not hard. When loaded they tend to creep i.e.
the extension gradually changes with time. Their properties dependent on temperature.
Ceramic: These are produced by baking naturally occurring clays at high temperatures
after molding to shape. They are used for high voltage insulators and high
temperature resistant cutting tool tips. They are basically Brittle relatively stronger in
compression than in tension, hard, chemically inert, and bad conductors of heat and
electricity.
Composite materials (composites): These are materials made up from, or composed of,
a combination of different materials to take overall advantage of their different properties.
In man-made composites, the advantages of deliberately combining materials in order to
obtain improved or modified properties were understood by ancient civilizations. An
example of this was the reinforcement of air-dried bricks by mixing the clay with straw.
This helped to reduce cracking caused by shrinkage stresses as the clay dried out. In more
recent times, horse hair was used to reinforce the plaster used on the walls and ceiling of
buildings. Again this was to reduce the onset of drying cracks. Nowadays, especially with
the growth of the plastics industry and the development of high-strength fibers, a vast
range combination of materials is available for use in composites. For example, carbon
fiber reinforced frames for tennis rackets and shafts for golf clubs have revolutionized
these sports.
The dual phase is produced by annealing in the (+) region, followed by cooling at a rate
which ensures that the -phase transforms to martensite, although some retained austenite
is also usually present, leading to a mixed martensiteaustenite (MA) constituent. To
allow air cooling after annealing, micro alloying elements are added to low-carbon
manganesesilicon steel, particularly vanadium or molybdenum and chromium.
Vanadium in solid solution in the austenite increases the hardenability but the enhanced
hardenability is due mainly to the presence of fine carbonitride precipitates which are
unlikely to dissolve in either the austenite or the ferrite at the temperatures employed and
thus inhibit the movement of the austenite/ferrite interface during the post-anneal cooling.
The martensite structure found in dual-phase steels is characteristic of plate martensite
having internal micro twins. The retained austenite can transform to martensite during
straining, thereby contributing to the increased strength and work hardening. Interruption
of the cooling, following intercritical annealing, can lead to stabilization of the austenite
with an increased strength on subsequent deformation. The ferrite grains (5m) adjacent
to the martensite islands are generally observed to have a high dislocation density
resulting from the volume and shape change associated with the austenite to martensite
transformation. Dislocations are also usually evident around retained austenitic islands
However, a number of automotive parts requiring very high strength steels, such as sills
and door reinforcements, have simple shapes. Therefore the steel is only slightly
deformed and the strain-hardening benefits of Dual Phase steels are not achieved. For this
reason, Arcelor Mittal has developed modified (HY - High Yield Strength and HHE High Hole Expansion) versions of Dual Phase steels offering high as-delivered yield
strength and good bendability and stretch flangeability. These new versions are
equivalent to the Complex Phase grades being developed on the German market.
Applications
Given their high energy absorption capacity and fatigue strength, cold rolled Dual Phase
Steels are particularly well suited for automotive structural and safety parts such as
longitudinal beams, cross members and reinforcements. Dual Phase 500 can be used to
make visible parts with 20% higher dent resistance than conventional high strength steels,
resulting in a potential weight saving of some 15%. As a result of its mechanical strength,
hot rolled Dual Phase 600 can be used to lightweight structural parts by reducing their
1.
2.
3.
4.
5.
Micro alloyed steel is a type of alloy steel that contains small amounts
of alloying elements (0.05 to 0.15%),
including niobium, vanadium, titanium, molybdenum, zirconium,boron, and rare-earth
metals. They are used to refine the grain microstructure or facilitate precipitation
hardening.
These steels lie, in terms of performance and cost, between carbon steel and low alloy
steel. Yield strength is between 500 and 750 MPa (73,000 and 109,000 psi) without heat
treatment.
Weldability is good, and can even be improved by reducing carbon content while
maintaining strength. Fatigue life and wear resistance are superior to similar heat-treated
steels. The disadvantages are that ductility and toughness are not as good as quenched
and tempered (Q&T) steels. They must also be heated hot enough for all of the alloys to
be in solution; after forming, the material must be quickly cooled to 540 to 600 C (1,004
to 1,112 F).
Cold-worked micro alloyed steels do not require as much cold working to achieve the
same strength as other carbon steel; this also leads to greater ductility. Hot-worked micro
alloyed steels can be used from the air-cooled state. If controlled cooling is used, the
material can produce mechanical properties similar to Q&T steels. Machinability is better
than Q&T steels because of their more uniform hardness and their ferritepearlite microstructure.
Because micro alloyed steels are not quenched and tempered, they are not susceptible
to quench cracking, nor do they need to be straightened or stress relieved. However,
because of this, they are through-hardened and do not have a softer and tougher core like
quench and tempered steels.
The requirement for structural steels to be welded satisfactorily has led to steels with
lower C (<0.1%) content. Unfortunately, lowering the C content reduces the strength and
this has to be compensated for by refining the grain size. This is difficult to achieve with
plain C-steels rolled in the austenite range, but the addition of small amounts of strong
carbide-forming elements (e.g. <0.1% Nb) causes the austenite boundaries to be pinned
by second-phase particles and fine grain sizes (<10m) to be produced by controlled
rolling.
Nitrides and carbonitrides as well as carbides, predominantly fcc and mutually soluble in
each other, may feature as suitable grain refiners in HSLA steels; examples include AlN,
Nb(CN), V(CN), (NbV)CN, TiC and Ti(CN). The solubility of these particles in the
austenite decreases in the order VC, TiC, NbC while the nitrides, with generally lower
solubility, decrease in solubility in the order VN, AlN, TiN and NbN. Because of the low
solubility of NbC, Nb is perhaps the most effective grain size controller. However, Al,V
andTi are effective in high-nitrogen steels, Al because it forms only a nitride, V and Ti by
forming V(CN) and Ti(CN), which are less soluble in austenite than either VC or TiC.
The major strengthening mechanism in HSLA steels is grain refinement, but the required
strength level is usually obtained by additional precipitation strengthening in the ferrite.
VC, for example, is more soluble in austenite than NbC, so if V and Nb are used in
combination, then on transformation of the austenite to ferrite, NbC provides the grain
TRIP steels
TRIP steels offer an outstanding combination of strength and ductility as a result of their
microstructure. They are thus suitable for structural and reinforcement parts of complex
shape. The microstructure of these steels is composed of islands of hard residual austenite
and carbide free bainite dispersed in a soft ferritic matrix. Austenite is transformed into
martensite during plastic deformation (TRIP: Transformation Induced Plasticity effect),
making it possible to achieve greater elongations and lending these steels their excellent
High strain hardening capacity and high mechanical strength lend these steels excellent
energy absorption capacity. TRIP steels also exhibit a strong bake hardening (BH) effect
Applications
As a result of their high energy absorption capacity and fatigue strength, TRIP steels are
particularly well suited for automotive structural and safety parts such as cross members,
longitudinal beams, B- pillar reinforcements, sills and bumper reinforcements.
Maraging steels
in FeNi martensites, some strong (Ti, Be), some moderate (Al, Nb, Mn, Mo, Si, Ta, V)
carbon.
The alloys generally have good weldability, resistance to hydrogen embrittlement and
stress corrosion, but are used mainly (particularly the 18% Ni alloy) for their excellent
combination of high strength and toughness.
The heat treatment includes heating and cooling operations or the sequence of two or
more such operations applied to any material in order to modify its metallurgical structure
definite rate.
Annealing, Normalizing, Hardening and Tempering are the four widely used heat
treatment processes that affect the structure and properties, and are assigned to meet the
specific requirements from the semi-fabricated and finished components. Steels being the
most widely used materials in major engineering fabrications undergo various heat
Annealing
Annealing refers to a wide group of heat treatment processes and is performed primarily
for homogenization, recrystallization or relief of residual stress in typical cold worked or
welded components.
Few important variants of annealing are full annealing, isothermal annealing, spheroidise
annealing, recrystallization annealing, and stress relief annealing.
Full annealing process consists of three steps. First step is heating the steel
component to above A3 (upper critical temperature for ferrite) temperature for
hypoeutectoid steels and above A1 (lower critical temperature) temperature for
hypereutectoid steels by 30-500C. In Figure, the terms , and Fe3C refer to
Isothermal annealing
Isothermal annealing consists of four steps. The first step is heating the steel components
similar as in the case of full annealing.
The second step is slightly fast cooling from the usual austenitizing temperature to a
constant temperature just below A1.
The third step is to hold at this reduced temperature for sufficient soaking period for the
completion of transformation and the final step involves cooling the steel component to
room temperature in air.
Figure depicts the heat treatment cycles of full annealing and isothermal annealing. The
terms , , P, PS and PFrefer to ferrite, austenite, pearlite, pearlite starting and pearlite
finish, respectively.
Isothermal annealing has distinct advantages over full annealing which are given below.
1. Reduced annealing time, especially for alloy steels which need very slow cooling to obtain
the required reduction in hardness by the full annealing.
2. More homogeneity in structure is obtained as the transformation occurs at the same time
throughout the cross section.
3. Improved machinability and surface finish is obtained after machining as compared to that
of the full annealed components.
Isothermal annealing is primarily used for medium carbon, high carbon and some of the
alloy steels to improve their machinability.
Spheroidise annealing
Spheroidise annealing is one of the variant of the annealing process that produces typical
microstructure consisting of the globules (spheroid) of cementite or carbides in the matrix
of ferrite. The following methods are used for spheroidise annealing
Holding at just below A1 Holding the steel component at just below the lower critical
temperature (A1) transforms the pearlite to globular cementite particles. But this process
is very slow and requires more time for obtaining spheroidised structure.
Thermal cycling around A1 In this method, the thermal cycling in the narrow temperature
range around A1 transforms cementite lamellae from pearlite to spheroidal. Figure
depicts a typical heat treatment cycle to produce spheroidised structure.
During heating above A1, cementite or carbides try to dissolve and during cooling they
try to re-form. This repeated action spheroidises the carbide particles.
Spheroidised structures are softer than the fully annealed structures and have excellent
machinability.
This heat treatment is utilized to high carbon and air hardened alloy steels to soften them
and to increase machinability, and to reduce the decarburization while hardening of thin
sections such as safety razor blades and needles.
Figure
depicts a typical heat treatment cycle to produce spheroidised structure.
Recrystallization annealing
The cold worked ferrite recrystallizes and cementite tries to spheroidise during this
annealing process.
Recrystallization annealing relieves the internal stresses in the cold worked steels and
weldments, and improves the ductility and softness of the steel. Refinement in grain size
is also possible by the control of degree of cold work prior to annealing or by control of
annealing temperature and time.
Stress relief annealing process consists of three steps. The first step is heating the cold
worked steel to a temperature between 5000C and 5500C i.e. below its recrystallization
temperature. The second step involves holding the steel component at this temperature for
1-2 hours. The final step is to cool the steel component to room temperature in air.
The stress relief annealing partly relieves the internal stress in cold worked steels without
loss of strength and hardness i.e. without change in the microstructure. It reduces the risk
of distortion while machining, and increases corrosion resistance. Since only low carbon
steels can be cold worked, the process is applicable to hypoeutectoid steels containing
less than 0.4% carbon. This annealing process is also used on components to relieve
internal stresses developed from rapid cooling and phase changes.
Normalizing
Normalizing process consists of three steps. The first step involves heating the
steel component above the A3 cm temperature for hypoeutectoid steels and above
A(upper critical temperature for cementite) temperature for hypereutectoid steels
by 300C to 500C (Figure 4.7.5).
The second step involves holding the steel component long enough at this
temperature for homogeneous austenization. The final step involves cooling the
hot steel component to room temperature in still air.
Due to air cooling, normalized components show slightly different structure and
properties than annealed components.
The properties of normalized components are not much different from those of
annealed components. However, normalizing takes less time and is more
convenient and economical than annealing and hence is a more common heat
treatment in industries.
Normalizing also improves the ductility without reducing the hardness and
strength.
Hardening
Different techniques to improve the hardness of the steels are conventional hardening,
martempering and austempering.
Conventional hardening
Conventional hardening process consists of four steps. The first step involves heating the
steel to above A3 temperature for hypoeutectoid steels and above A1 temperature for
hypereutectoid steels by 500C.
The second step involves holding the steel components for sufficient socking time for
homogeneous austenization. The third step involves cooling of hot steel components at a
rate just exceeding the critical cooling rate of the steel to room temperature or below
room temperature.
The final step involves the tempering of the martensite to achieve the desired hardness.
Detailed explanation about tempering is given in the subsequent sections. In this
conventional hardening process, the austenite transforms to martensite. This martensite
structure improves the hardness.
1. Proper quenching medium should be used such that the component gets cooled at a rate
just exceeding the critical cooling rate of that steel.
2. Alloy steels have less critical cooling rate and hence some of the alloy steels can be
hardened by simple air cooling.
3. High carbon steels have slightly more critical cooling rate and has to be hardened by oil
quenching.
4. Medium carbon steels have still higher critical cooling rates and hence water or brine
quenching is necessary.
Figure depicts the conventional hardening process which involves quenching and
tempering. During quenching outer surface is cooled quicker than the center. Thinner
parts are cooled faster than the parts with greater cross-sectional areas. In other words the
transformation of the austenite is proceeding at different rates. Hence there is a limit to
the overall size of the part in this hardening process.
Martempering (marquenching)
Further cooling is continued through the martensite region, followed by the usual
tempering. In this process, the transformation of austenite to martensite takes
place at the same time throughout the structure of the metal part.
Austempering
This process is also used to overcome the limitation of the conventional hardening
process. Figure depicts the austempering process. Here the quench is interrupted at a
higher temperature than for martempering to allow the metal at the center of the part to
reach the same temperature as the surface.
By maintaining that temperature, both the center and surface are allowed to transform to
bainite and are then cooled to room temperature.
Austempering causes less distortion and cracking than that in the case of martempering
and avoids the tempering operation. Austempering also improves the impact toughness
and the ductility of the metal than that in the case of martempering and conventional
hardening.
Tempering
The hardened steel is not readily suitable for engineering applications. It possesses
following three drawbacks.
Martensite obtained after hardening is extremely brittle and will result in failure
of engineering components by cracking.
The tempering temperature is decided based on the type of steel. Highly alloyed tool
steels are tempered in the range of 500 0C - 6000C. Low alloy construction steels are
tempered above 4000C to get a good combination of strength and ductility. Spring steels
are tempered between 3000C - 4000C to get the desired properties. Figure depicts the
influence of tempering temperature on the properties of steel. It is observed that the
increase in the tempering temperature decreases the hardness and internal stresses while
increases the toughness.