Professional Documents
Culture Documents
Cassette
Cassette Feeding Unit-Y1/Y2
Oct 26 2004
Application
This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and
repair of products. This manual covers all localities where the products are sold. For this reason, there may be
information in this manual that does not apply to your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products.
When changes occur in applicable products or in the contents of this manual, Canon will release technical information
as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will
issue a new edition of this manual.
The following paragraph does not apply to any countries where such provisions are inconsistent with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks of the individual companies.
Copyright
This manual is copyrighted with all rights reserved. Under the copyright laws, this manual may not be copied,
reproduced or translated into another language, in whole or in part, without the written consent of Canon Inc.
Caution
Use of this manual should be strictly supervised to avoid disclosure of confidential information.
Introduction
Symbols Used
This documentation uses the following symbols to indicate special information:
Symbol
Description
Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning.
Indicates an item requiring disconnection of the power plug from the electric outlet.
Indicates an item intended to provide notes assisting the understanding of the topic in question.
Memo
Introduction
represents the path of mechanical drive; where a signal name accompanies the symbol ,
indicates the direction of the electric signal.
The expression "turn on the power" means flipping on the power switch, closing the front door, and closing the
delivery unit door, which results in supplying the machine with power.
2. In the digital circuits, '1'is used to indicate that the voltage level of a given signal is "High", while '0' is used to
indicate "Low".(The voltage value, however, differs from circuit to circuit.) In addition, the asterisk (*) as in
"DRMD*" indicates that the DRMD signal goes on when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field. Therefore, the
operations of the microprocessors used in the machines are not discussed: they are explained in terms of from
sensors to the input of the DC controller PCB and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product improvement or other
purposes, and major changes will be communicated in the form of Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant
Service Information bulletins and be able to identify and isolate faults in the machine."
Contents
Contents
1 Installation Procedure
1.1 Unpacking and Chacking the Components ........................................................................................................... 2
1.1.1Unpacking and Checking the Components ..................................................................................................... 2
1.2 Installation Procedure............................................................................................................................................ 3
1.2.1Turning Off the Host Machine ........................................................................................................................ 3
1.2.2Installation Procedure...................................................................................................................................... 3
1.3 Making Adjustments ............................................................................................................................................. 7
1.3.1A. Adjusting the Horizontal Registration (1st side; mechanical).................................................................... 7
1.3.2B.Adjusting the Horizontal Registration (2nd side; only when installing an iR C3100 Series machine)....... 8
Contents
Chapter 1Installation
Procedure
Chapter 1
0004-5101
Open the shipping box, and check to make sure that none of the following is missing:
[1]
[2]
A3
A3
A4
A4
A4 R
A5 R
B4
B4
[3]
B5
11 17
A3B5 B11
5 17 11 17
AB
35R BLEGAL
11 17
5
305
457
mm
R
A4
B5
LEGAL
LEGAL
305 457LTR
mm
AEXEC
4
LEGAL
EXEC
R
FLSC
A4
LTR
LTR
FLSC
R
FOLIO
A5
LTR
LTR R
FOLIO
BOFICIO
4
STMT R LTR R
OFICIO
B4
12 18 STMT R
12 18
81/2 14
81/2 14
81/2 11
81/2 14
81/2 14
81/2 11
81/2 11
81/2 11
81/2 11
51/2 81/2
81/2 11
51/2
81/2
FC5-0597
FC5-0597
[4]
[5]
F-1-1
T-1-1
[1]
1 unit
[2]
2 pc.
[3]
Dial label
1 pc.
[4]
2 pc.
[5]
Fixing screw L
1 pc.
[6]
FCC/IC sheet
1 pc.
Chapter 1
switch.
3. Turn off the main power switch.
4. Disconnect the power cable (from the wall outlet).
0007-2468
[1]
ON
/OF
F
iR C3100 Series
Before starting the work, be sure to go through the
following on the host machine:
1. Turn off the control panel power switch.
2. Turn off the main power switch.
3. Disconnect the power cable (from the power
outlet).
[2]
[3]
[4]
F-1-3
0004-5111
/O
FF
[1] OFF
[2] OFF
[3] Disconnect.
F-1-2
iR2000 Series
Be sure to go through the following steps on the host
F-1-4
or more.
Chapter 1
F-1-5
F-1-6
5) Holding the 4 grips of the host machine, place it on
the machine.
[1]
F-1-7
7) Press the release button on the cassette, and take out
When placing its host machine on the machine, be
sure that the 2 positioning pins [1] found on top of the
machine are fitted into the holes in the bottom plate of
cassette 1/2.
8) Join the machine and the pedestal using the
included fixing screw [1].
F-1-8
Chapter 1
14) Attach the dial label [1] from the right side of the
[1]
[1]
F-1-9
11) Out the Lattice connector cover Fit the lattice
connector [1] of the machine into its host machine.
[3]
[1]
[1]
F-1-10
[2]
F-1-12
12) Attach the dial label to the cassette detecting dial.
(Be sure to select the AB or Inch label to suit the size
of paper to be used.)
13) Turn the size detecting dial [2] so that the position
[2]
F-1-13
[1]
F-1-11
Chapter 1
front cover.
[1]
F-1-14
18) Connect the power cable to the power outlet.
19) Turn on the main power switch.
Chapter 1
0004-5130
1) Make copies using cassette 3/4 as the source of paper; then, check to make sure that the leading edge margin is
2.5 +/-1.5 mm.
(-)
(+)
0
2
4
6
8
10
2.51.5mm
F-1-15
[1]
[2]
F-1-16
3) Slide out the cassette 3/4.
4) Check the position of the index.
Chapter 1
F-1-17
5) Fit a screwdriver through the hole [2] of the right support to reach the horizontal registration assembly [1] of the
cassette to adjust.
6) Then, loosen the fixing screw [3].
F-1-18
7) Move the horizontal registration adjusting plate [4] to the front and the rear to suit the index you checked in step 4).
8) Make copies using the cassette you have adjusted as the source of paper, and check to see that the blank (front
side) of the image (front side) is 2.5 +/- 1.5 mm.
9) Tighten the fixing screw.
10) Mount the machine's right front cover.
11) Slide in the cassette 3/4.
0004-5141
1) Start service mode, and check the adjustment value used for the horizontal registration of the 2nd size for the
cassette 1.
-COPIER>ADJUST>FEED-ADJ>ADJ-C1RE
2) Enter the adjustment value of the leading edge margin for the 2nd side of a sheet assigned to cassette 1 into the
field for the leading edge margin for the 2nd side of a sheet assigned to cassette 3/4.
-COPIER>ADJUST>FEED-ADJ>ADJ-C3RE
Chapter 1
-COPIER>ADJUST>FEED-ADJ>ADJ-C4RE
3) Make double-sided copies using cassette 3/4 as the source of paper, and check to make sure that the leading edge
margin is 2.5 +/- 2 mm.
(-)
(+)
0
2
4
6
8
10
2.52.0mm
F-1-19
-If the horizontal registration for the cassette 3 or 4 is not as indicated, make the following adjust ments:
4) Start service mode, and enter the new adjustment value:
-COPIER>ADJUST>FEED-ADJ>ADJ-C3RE
-COPIER>ADJUST>FEED-ADJ>ADJ-C4RE
If the adjustment value is in creased for 1, an image shifts to the paper feeding direction by 0.1 mm.
5) Press the Reset key twice to end service mode.
Oct 26 2004