You are on page 1of 6

123D Design Tutorial: Alloy wheel or steering wheel

Before using these instructions, it is very helpful to watch this video screencast of the CAD drawing
actually being done in the software. Click this link for the video instructions

Start in TOP view, and


select Sketch Circle
Click on the grid to start sketching and
click on one of the large square crosses
for the centre of your circle.
Draw a circle 50mm diameter

Use Sketch Offset to draw another


circle 5mm outside the original circle,
so your sketch looks as below.

You will now start drawing the


spoke sections of the wheel so
that it looks like this

Select Sketch Three Point Arc and click


on your wheel to add to this sketch

Click to specify the start point


2 small squares to the left of
the wheel. Then the end point
make this 2 small squares to
the right of the wheel

Drag the mouse along the arc until the


mouse pointer is one square above the
centre of the circle, then left click once
to fix this point on the arc.

Page 1 of 6
Diane Burton, STEM Outreach. D.S.Burton@warwick.ac.uk

Click on the
same start and
end points to
draw the next
arc so it mirrors
the first arc.
Select the point on the arc one
square below the centre of the
circle.
Now start the next arc 2 small
squares above and below the
circle point on the arc, one
square to the side of the centre.

Sketch the final arc


Your drawing will
look like this.

Use Sketch Trim


to remove the
outer bits of the
sketch so it
looks like this

Use Sketch Circle to draw a 10mm


diameter circle in the centre square.
Your drawing should look like this.

Page 2 of 6
Diane Burton, STEM Outreach. D.S.Burton@warwick.ac.uk

Select Sketch Ellipse and click


in the centre of this section
this will be the centre point
of your ellipse shape.
Left click one square
along to show the axis
point of the ellipse.
Then drag your mouse to
specify the point on ellipse
you want this to be 2,
type 2 in the box, left click
and press enter.
Use Sketch Ellipse to put
a matching ellipse shape
on the other side
Use Sketch Circle to draw 4 circles as shown
This one is 5mm diameter and this one is 4mm diameter. Note where the centre of each circle is.
Your finished sketch should look like this.

SAVE YOUR
WORK!

Select Sketch Trim


and click on the wheel
and begin to trim the
lines you dont need
as shown.
Your finished sketch
will look like this.

Page 3 of 6
Diane Burton, STEM Outreach. D.S.Burton@warwick.ac.uk

Select the outer ring and use Construct


Extrude to extrude by 4mm height.

Do the same with the inner part of the


drawing extrude to 4mm height.

Select Modify Fillet and


then click on the outer
ring of the wheel put
4 in the fillet radius
box then press enter.

Select Modify Chamfer


and click on each of the
ellipses put 1.5 in the
chamfer distance box
then press enter.

Select Modify Chamfer


again and select each of
the circle and chamfer
by a distance of 1.

SAVE YOUR
WORK!

Page 4 of 6
Diane Burton, STEM Outreach. D.S.Burton@warwick.ac.uk

Select Modify Fillet and then left click on each of the inner
spoke edges in turn to select them. Fillet by radius of 1,
then press enter to finish.
Your
drawing
should look
like this.

Select the Pattern Mirror tool


Select the wheel as the Solid (it
highlights bright blue when selected).
Click on Mirror Plane and turn the
screen to select the underside of the
wheel.
The shape will mirror to produce a
duplicate shape press enter to finish.

Your drawing will


look like this

SAVE YOUR
WORK!

Add the centre solid piece of the wheel with a rounded top piece
Select Construct Extrude and click on the centre circle sketch extrude by 5.5mm.
Remember that you extruded the rest of the wheel by 4mm, so
the centre circle will protrude by 1.5mm (5.5 4 = 1.5).

Use Modify
Fillet to
round off the
centre piece

Page 5 of 6
Diane Burton, STEM Outreach. D.S.Burton@warwick.ac.uk

Rotate the screen to look at the underside of the wheel and you will see there is a hole
(this is because you mirrored the wheel before you extruded the centre circle.
You can extrude this
centre piece now by
selecting Construct
Extrude and clicking
on the centre circle.

Pull the yellow arrow to extrude by how much


you want. It will be a negative number as you are
extruding downwards.

-4mm will put it flush with the rest of the wheel,


-2mm will leave an indent, whereas more than
More than -4mm will leave a protruding
cylinder that could be an axle or steering
column.
SAVE YOUR
WORK!

Click the drop down on the top left of


your screen and select Export STL

Page 6 of 6
Diane Burton, STEM Outreach. D.S.Burton@warwick.ac.uk

You might also like