Professional Documents
Culture Documents
The leading edge is the forwardmost point on the airfoil. In general, this does not necessarily
mean it is the first part of the shape contacting the fluid flow. However, by convention this is
true for an angle of attack of zero degrees, in which the local fluid velocity and the chordline are
parallel. The trailing edge is a similar point on the most rearward part of the airfoil. Airfoils are
commonly tapered or have a corner (in the mathematical sense) at the trailing edge. This is to
reduce the change in velocity needed for streamlines passing on the upper and lower edges to
come back together in laminar flow. The mean camber line is hallway between the upper and
lower surfaces, and the camber is the measurement of the difference from this line to the
chordline connecting the leading and trailing edges. The thickness, by American convention, is
measured perpendicular to the mean camber line, and is commonly not more than about 20% of
the chord measurement.
We define the following unit vectors for our two-dimensional surface:
All fluids have some measurable viscosity. Viscosity is the measurement of how thick a fluid
is, whether it behaves more like water or like molasses. A more viscous fluid, all things being
equal, flows more slowly. In fact, what we have on a molecular level is friction, the interaction
between fluid particles and with objects to resist motion. Air, like other gases, has very low
viscosity. In many types of airflow we can even neglect it. We call these types of flows inviscid.
Early aerodynamics focused on the behavior of potential flow, which assumes that the flow is
inviscid as well as irrotational (no local rotation or vortices). It is called a potential flow
because the resulting fluid behavior is governed by a form of Laplaces equation. Solutions to
this equation are called potential functions. They have many useful properties and are widely
studied. We can derive many useful results, including fluid flow around an airfoil, using
potential theory. However, a major problem with potential theory (known as early as the 1700s)
is that it predicts zero drag for objects in the flow. However, it was known at the time that drag
(at least as far as we have discussed it resistance to the fluid flow) was observed to occur
around boats and therefore the potential theory did not accurately describe the real world. This
discrepancy is known as dAlemberts paradox. It turns out that this paradox arises from the
inviscid assumption. We must have friction within the fluid to predict the drag forces observed
at the time around boats. We confine this viscous behavior to an extremely narrow region near
the surface, called the boundary layer. According to viscous theory, a fluid at an interface like a
wall (or an airfoil surface) has zero velocity. But, we also know that the streamlines show a
nonzero velocity away from the surface. Over the boundary layer, we see a sharp transition from
the zero velocity fluid at the surface to the local inviscid flow solution. The energy that this
transition takes is exerted on the body as a shear force (or, along the direction of the surface), as
shown:
The first term is the force due to air pressure on the body, while the second is due to friction
forces. In general, this resultant is not aligned with either axes of a coordinate system placed on
the body. As discussed before, we generally use the incoming air velocity as the horizontal of
our coordinate system for an airfoil. So, this resultant force on an airfoil at a positive angle of
attack becomes:
reference point that we use (and therefore where we locate the resulting lift and drag forces)
there will be a moment associated with that point. At some point, the resulting moment will be
zero. If we applied the lift and drag forces we calculated to the body at this point, it will exactly
match the actual loads distributed across the surface. We call this point the center of pressure. It
is not typically easy to calculate for realistic geometries, and changes with the angle of attack as
the pressure distribution changes. We therefore consider fixed points of the geometry and resign
ourselves to the existence of a moment trying to change our angle of attack. We can see this
phenomenon by sticking a piece of cardboard out the window of a moving car, or into a breeze.
What happens? In most cases, when allowed to rotate freely, the cardboard tries to flip over in
one direction or the other. The same happens to an airfoil. In fact, when allowed to rotate,
neither the cardboard or our airfoil are very useful for an extended period of time. That is what
this class is all about.
By convention, moments that tend to increase angle of attack are positive. Two points we
commonly refer to are the moment at the leading edge, MLE, and the moment at the quarterchord, or 25% from the leading edge towards the trailing edge, Mc/4. In general both of these
may change as a function of the angle of attack. In theory, there exists a single fixed point that
has a moment independent of the angle of attack, called the aerodynamic center. We will
discuss the aerodynamic center in further detail later.
Historically, aerodynamics has made much of dimensionless systems. This has made it easier to
exchange information between countries but, more importantly, allows for scale testing such as
that done in a wind tunnel. As long as 2 special parameters match, the aerodynamic flows are
dynamically similar. This means that the results obtained in one case (for instance in a wind
tunnel) can be scaled and compared to another (like the real world). One of these parameters is
the local mach number, which is the ratio of the fluid velocity, V, to the speed of sound in the
fluid, a:
The second parameter that must match for two flows to be dynamically similar is the Reynolds
number, Re. The Reynolds number is also dimensionless, and relates the momentum energy of a
flow to the viscous energy of the flow. It requires us to use a characteristic size, which we
choose to be the chord length, c. Then, using the local fluid density, , and the fluid viscosity,
, we have:
We can then compare for two different problems, not the lift and drag forces directly, but
dimension coefficients that represent those forces. We first define the local dynamic pressure as
Note that dynamic pressure has the same units as pressure, or force per unit area. Given a
suitable reference area, we can then nondimensionalize our system. The commonly chosen
example is the wing planform area, S. This is the projected area of the wing onto a plane.
Our coefficient of lift is therefore computed as
Historically, we know that for most airfoils the drag coefficient is strong function of the lift
coefficient. In fact, in most cases we can express this relationship as a quadratic, using two
parameters CD,0 and K:
This relationship is often called the drag polar, and is shown in the figure below:
lift that we add to this constant is often called induced drag, because it is an effect induced by lift
production.
Similar to the lift and drag coefficients, the nondimensional measure of our airfoil moment is the
moment coefficient:
Where we typically use the chord, c, as the needed relative length measurement. Again, the value
of this moment will vary depending on the location around which it is measured. We will have
various moment coefficients possible, such as that at the leading edge, the coefficient at the
quarter chord point (why is this point important?), and the moment at the aerodynamic center.
Earlier, we discussed the concept of the aerodynamic center. This is the point on the airfoil
where the moment is independent of angle of attack. To find this point, we first need a point of
reference. For convenience, we choose the quarter chord point. Wherever it is, we can find the
moment at the aerodynamic center using a transformation of the moment from the quarter-chord
by applied the force(lift) and the distance between the two points:
Now, if we take the derivative with respect to the angle of attack, we know that it must be zero at
the aerodynamic center:
So we can then find the location of the aerodynamic center. If the lift coefficient and the
moment coefficient at the quarter-chord are linear functions of angle of attack, with slopes m0
and a0 respectively, then the location in terms of the chord is:
Thin airfoil theory predicts that the lift coefficient of a flat plate is
And that the moment at the quarter chord is zero. Therefore, the aerodynamic center is the
quarter-chord point. We can compute using the same process, but measured from the leading
edge. The same theory predicts that the coefficient of the moment at the leading edge is
From which we can calculate the distance of the aerodynamic center from the leading edge to be
From this type of data, we get our airfoil lift coefficient derivative, a0. These are often corrected
for the effects of having a finite length using the following formulas using Prandtls lifting line
theory (note that the use of a variable as a subscript has the usual meaning of differentiation):
Where e1 is an efficiency parameter usually 0.90-0.95. For low aspect ratio wings, we can use
the formula called Helmbolds relation:
References:
[1] B.N. Pamadi, Performance, Stability, Dynamics, and Control of Airplanes, AIAA, 2004.
[2] J.D. Anderson, Aircraft Performance and Design, McGraw-Hill, 1999.
axis of the aircraft, known as roll motion. By moving only one aileron, we can increase the lift
of one side of the aircraft, generating a moment about the roll axis. We can get a similar effect
by lowering one aileron and raising the other. The ailerons function changing the lift balance
between the right and left sides of the aircraft. The elevators affect rotational motion around an
axis parallel to the wings, known as the pitch axis. They work in uniform motion on both sides
of the aircraft to generate additional (or less) lift on the tail, generating a moment that allows the
aircraft to pitch down (or up). The rudder works like a conventional rudder in a boat, but we can
also think of it as an airfoil. When neutral, the rudder generates no lift. When moved to one
side, it alters the camber of the airfoil, increasing lift towards the opposite side. This causes a
moment about the vertical axis, known as yaw motion, bringing the aircraft nose around in the
direction of the rudder.
These three types of rotational motion bring the total number of system variables to 6 (including
3 translation components). We typically call this type of system 6-DOF for 6 degrees of
freedom. To set a system of notation, we choose to follow the designation in the text.
Notice we have position and velocity along 3 axes, plus angle of rotation and rate of rotation.
Even though we have 6 degrees of freedom, we typically need 12 variables to solve the 2nd order
equations of motion that result. Also note that, in this fixed body reference frame, rotations of
the craft about the x axis are roll motion, rotations about y are pitch motion, and rotations about z
are yaw motion.
In this course, we assume the Earth to be an inertial (nonaccelerating) reference system. We use
FE to denote this reference frame. The velocity of the aircraft relative to the stationary Earth is
denoted by the vector VE, called the groundspeed. The velocity of the air above the Earth (the
wind) is denoted by the vector W, while the velocity of the aircraft with respect to the air is the
vector V, known as the airspeed. Clearly, the airspeed is responsible for the aerodynamic forces
generated by the aircraft. The relationship between these reference frames is
Unless otherwise noted, we can assume that W = 0 for most derivations since we are interested
in the behavior of the aircraft, not its position relative to the ground. The reference frame fixed
to the body is denoted by FB. In this frame, the air approaches the fixed center of gravity for the
airplane with a velocity of V. Consider motion in the two coordinate planes shown in the
figure below:
References:
[1] J.D. Andersen, Introduction to Flight, McGraw-Hill, 2012.
[2] B. Etkin and L.D. Reid, Dynamics of Flight: Stability and Control, John Wiley & Sons, 1996.
Which are our basic relationships for steady, level flight. Steady implies that the conditions are
unchanging, since both components of velocity, parallel and perpendicular to the current
direction, are not being changed. In this case, the thrust required of our engine must exactly
match the drag produced, and the lift produced must exact balance the weight of the aircraft.
With these met, the velocity remains unchanged and the aircraft does not change elevation.
We can find out some things about this case. Since lift depends on angle of attack, we assume
the following relationship
Where 0 is the angle of attack producing zero lift. We then have, from the balance with weight:
Since a typical maximum angle of attack before stall is approximately 10 degrees, we naturally
have a limit to the weight of the aircraft. Similarly, thrust required is
We can then note that there is a minimum thrust required for each velocity, and that thus thrust
increases relative to the square of the aircraft weight. Another type of performance condition is
steady, gliding flight. This condition would have a nonzero and zero thrust. In this case, we
start with the same equations
Assuming T = 0 results in
So to minimize the glide angle (and therefore our time in the air from a fixed height) we need a
maximum L/D ratio (small D/L). The problem is exactly the same for a steady climb, except
now we add thrust to the equations (assuming = 0):
before, for steady level flight, we had T = D. Now, we have a certain amount of thrust above
and beyond that amount. From trigonometry, we know that the rate of climb will be V sin ,
resulting in:
Since force times velocity is power, the rate of climb is the ratio of excess power (that available
above and beyond the amount needed to balance drag) to weight. Note that, for the case of T=0
and negative flight path angle, this reduces to the same result for a steady glide.
Consider the sketch of the next scenario, in which an aircraft undergoes a steady turn:
Where R is the radius of curvature, as shown. Considering the fact that we must maintain a
constant velocity, we now have a balance of forces of: